LINKSYS WMP54GR Wireless-G PCI Adapter with RangeBooster User Manual Book

LINKSYS LLC Wireless-G PCI Adapter with RangeBooster Book

Manual

A Division of Cisco Systems, Inc.®Model No.PCI Adapter Wireless-GWMP54GRUser GuideWIRELESSGHz2.4802.11gwith RangeBooster
Wireless-G PCI Adapter with RangeBoosterCopyright and TrademarksSpecifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2006 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.How to Use This User GuideThis User Guide has been designed to make understanding networking with the Wireless-G PCI Adapter with RangeBooster easier than ever. Look for the following items when reading this User Guide:In addition to these symbols, there are definitions for technical terms that are presented like this:Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like this:Figure numbers and descriptions can also be found in the “List of Figures” section in the “Table of Contents”. This exclamation point means there is a caution or warning and is something that could damage your property or the Wireless-G PCI Adapter with RangeBooster.This checkmark means there is a note of interest and is something you should pay special attention to while using the Wireless-G PCI Adapter with RangeBooster.This question mark provides you with a reminder about something you might need to do while using the Wireless-G PCI Adapter with RangeBooster.word: definition.Figure 0-1: Sample Figure DescriptionWMP54GR-UG-51219NC BWWARNING: This product contains chemicals, including lead, known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.
Wireless-G PCI Adapter with RangeBoosterTable of ContentsChapter 1: Introduction 1Welcome 1What’s in this Guide? 2Chapter 2: Planning your Wireless Network 4Network Topology 4Roaming 4Network Layout 5Chapter 3: Setting up and Connecting the Wireless-G PCI Adapter with RangeBooster 6Starting the Setup 6Connecting the Adapter 7Setting up the Adapter 7Chapter 4: Using the Wireless Network Monitor 16Accessing the Wireless Network Monitor 16Using the Wireless Network Monitor 16Link Information 16Site Survey 19Profiles 20Create a New Profile 21Appendix A: Troubleshooting 30Common Problems and Solutions 30Frequently Asked Questions 31Chapter B: Using Windows XP Wireless Configuration 34Appendix C: Wireless Security 37Security Precautions 37Security Threats Facing Wireless Networks 37Appendix D: Windows Help 40Appendix E: Glossary 41Appendix F: Specifications 44Appendix G: Warranty Information 46Appendix H: Regulatory Information 47Appendix I: Contact Information 53
Wireless-G PCI Adapter with RangeBoosterList of FiguresFigure 3-1: Setup Wizard’s Welcome Screen 6Figure 3-2: Setup Wizard’s License Agreement 6Figure 3-3: Connecting the Adapter 7Figure 3-4: Available Wireless Network 7Figure 3-5: WEP Key Needed for Connection 8Figure 3-6: WPA - Personal Needed for Connection 8Figure 3-7: PSK2 Needed for Connection 9Figure 3-8: Congratulations 9Figure 3-9: Available Wireless Network 10Figure 3-10: Network Settings 10Figure 3-11: Wireless Mode 10Figure 3-12: Ad-Hoc Mode Settings 11Figure 3-13: Wireless Security - WEP 11Figure 3-14: Wireless Security - WPA Personal 12Figure 3-1: Wireless Security - PSK2 12Figure 3-15: Wireless Security - WPA Enterprise - EAP-TLS 13Figure 3-16: Wireless Security - WPA Enterprise - PEAP 13Figure 3-17: Wireless Security - RADIUS - EAP-TLS 14Figure 3-18: Wireless Security - RADIUS - PEAP 14Figure 3-19: Confirm New Settings 15Figure 3-20: Congratulations screen 15Figure 4-1: Wireless Network Monitor Icon 16Figure 4-2: Link Information 16Figure 4-3: More Information - Wireless Network Status 17Figure 4-4: More Information-Network Statistics 18Figure 4-5: Site Survey 18Figure 4-6: WEP Key Needed for Connection 19Figure 4-7: WPA-Personal Needed for Connection 19Figure 4-8: PSK2 Needed for Connection 19Figure 4-9: Profiles 20
Wireless-G PCI Adapter with RangeBoosterFigure 4-10: Import a Profile 20Figure 4-11: Export a Profile 20Figure 4-12: Create a New Profile 21Figure 4-1: WEP Key Needed for Connection 21Figure 4-2: WPA - Personal Needed for Connection 22Figure 4-3: PSK2 Needed for Connection 22Figure 4-4: Congratulations 22Figure 4-13: Available Wireless Network 23Figure 4-14: Network Settings 23Figure 4-15: Wireless Mode 24Figure 4-16: Ad-Hoc Mode Settings 24Figure 4-17: Wireless Security - WEP 25Figure 4-18: Wireless Security - WPA Personal 25Figure 4-19: Wireless Security - PSK2 26Figure 4-20: Wireless Security - WPA Enterprise Using EAP-TLS 27Figure 4-21: Wireless Security - WPA Enterprise Using PEAP 27Figure 4-22: Wireless Security - RADIUS Using EAP-TLS 28Figure 4-23: Wireless Security - RADIUS Using PEAP 28Figure 4-24: Confirm New Settings for New Profile 29Figure 4-25: Congratulations 29Figure B-1: Wireless Network Monitor Icon 34Figure B-2: Windows XP - Use Windows XP Wireless Configuration 34Figure B-3: Windows XP Wireless Configuration Icon 34Figure B-4: Available Wireless Network 35Figure B-5: No Wireless Security 35Figure B-6: Network Connection - Wireless Security 36Figure B-7: Wireless Network Connection 36
1Chapter 1: IntroductionWelcomeWireless-G PCI Adapter with RangeBoosterChapter 1: IntroductionWelcomeThank you for choosing the Wireless-G PCI Adapter with RangeBooster. With this Adapter, your wireless networking experience will be faster and easier than ever.How does the Adapter do this? Like all wireless products, the Adapter allows for greater range and mobility within your wireless network. And with RangeBooster, the range and speed will be even greater. This adapter communicates over the 54Mbps 802.11g wireless standard, but can also communicate with the widely used 11Mbps 802.11b standard.But what does all of this mean? Networks are useful tools for sharing computer resources. You can access one printer from different computers and access data located on another computer's hard drive. Networks are even used for playing multiplayer video games. So, networks are not only useful in homes and offices, they can also be fun.PCs equipped with wireless cards and adapters can communicate without cumbersome cables. By sharing the same wireless settings, within their transmission radius, they form a wireless network. Use the instructions in this Guide to help you connect the Adapter, set it up, and configure it for your network. These instructions should be all you need to get the most out of the Adapter.802.11b: an IEEE wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHzadapter: a device that adds network functionality to your PC.network: a series of computers or devices connected for the purpose of data sharing, storage, and/or transmission between users.802.11g an IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of 2.4GHz, and backward compatibility with 802.11b devices.Mbps: one million bits per second; a unit of measurement for data transmission
2Chapter 1: IntroductionWhat’s in this Guide?Wireless-G PCI Adapter with RangeBoosterWhat’s in this Guide?This user guide covers the steps for setting up and using the Wireless-G PCI Adapter with RangeBooster.• Chapter 1: IntroductionThis chapter describes the Adapter’s applications and this User Guide.• Chapter 2: Planning Your Wireless NetworkThis chapter discusses a few of the basics about wireless networking.• Chapter 3: Setting Up and Connecting the PCI AdapterThis chapter shows you how to setup and connect the Adapter.• Chapter 4: Using the Wireless Network Monitor This chapter show you how to use the Adapter’s Wireless Network Monitor.• Appendix A: TroubleshootingThis appendix describes some problems and solutions, as well as frequently asked questions, regarding installation and use of the Adapter.• Appendix B: Windows XP Wireless Zero ConfigurationThis chapter instructs you on how to install Window XP Wireless Zero Configuration• Appendix C: Wireless SecurityThis appendix discusses security issues regarding wireless networking and measures you can take to help protect your wireless network.• Appendix D: Windows HelpThis appendix describes how you can use Windows Help for instructions about networking, such as installing the TCP/IP protocol.• Appendix E: GlossaryThis appendix gives a brief glossary of terms frequently used in networking.• Appendix F: SpecificationsThis appendix provides the Adapter’s technical specifications.• Appendix G: Warranty InformationThis appendix supplies the Adapter’s warranty information.• Appendix H: Regulatory InformationThis appendix supplies the Adapter’s regulatory information.
3Chapter 1: IntroductionWhat’s in this Guide?Wireless-G PCI Adapter with RangeBooster• Appendix I: Contact InformationThis appendix provides contact information for a variety of Linksys resources, including Technical Support.
4Chapter 2: Planning your Wireless NetworkNetwork TopologyWireless-G PCI Adapter with RangeBoosterChapter 2: Planning your Wireless NetworkNetwork TopologyA wireless network is a group of computers, each equipped with one wireless adapter. Computers in a wireless network must be configured to share the same radio channel. Several PCs equipped with wireless cards or adapters can communicate with one another to form an ad-hoc network.Linksys wireless adapters also provide users access to a wired network when using an access point or wireless router. An integrated wireless and wired network is called an infrastructure network. Each wireless PC in an infrastructure network can talk to any computer in a wired network infrastructure via the access point or wireless router.An infrastructure configuration extends the accessibility of a wireless PC to a wired network, and can double the effective wireless transmission range for two wireless adapter PCs. Since an access point is able to forward data within a network, the effective transmission range in an infrastructure network can be doubled.RoamingInfrastructure mode also supports roaming capabilities for mobile users. Roaming means that you can move your wireless PC within your network and the access points will pick up the wireless PC's signal, providing that they both share the same channel and SSID.Before enabling you consider roaming, choose a feasible radio channel and optimum access point position. Proper access point positioning combined with a clear radio signal will greatly enhance performance.infrastructure: a wireless network that is bridged to a wired network via an access point.ad-hoc: a group of wireless devices communicating directly with each other (peer-to-peer) without the use of an access point.roaming: the ability to take a wireless device from one access point's range to another without losing the connection.ssid: your wireless network's name.topology: the physical layout of a network.access point: a device that allows wireless-equipped computers and other devices to communicate with a wired network. Also used to expand the range of a wireless network
5Chapter 2: Planning your Wireless NetworkNetwork LayoutWireless-G PCI Adapter with RangeBoosterNetwork LayoutLinksys wireless access points and wireless routers have been designed for use with 802.11a, 802.11b, and 802.11g products. With 802.11g products communicating with the 802.11b standard and some products incorporating both “a” and “g”, products using these standards can communicate with each other.Access points and wireless routers are compatible with 802.11a, 802.11b and 802.11g adapters, such at the PC Cards for your laptop computers, PCI Card for your desktop PC, and USB Adapters for when you want to enjoy USB connectivity. Wireless products will also communicate with the wireless PrintServer.When you wish to connect your wired network with your wireless network, network ports on access points and wireless routers can be connected to any of Linksys's switches or routers.With these, and many other, Linksys products, your networking options are limitless. Go to the Linksys website at www.linksys.com for more information about wireless products. router: a networking device that connects multiple networks togetherswitch: a data switch that connects computing devices to host computers, allowing a large number of devices to share a limited number of ports
6Chapter 3: Setting up and Connecting the Wireless-G PCI Adapter with RangeBoosterStarting the SetupWireless-G PCI Adapter with RangeBoosterChapter 3: Setting up and Connecting the Wireless-G PCI Adapter with RangeBoosterStarting the SetupThe Wireless-G PCI Adapter Setup Wizard will guide you through the installation procedure. The Setup Wizard will install the driver and Wireless Network Monitor, as well as connect and configure the Adapter.Insert the Setup Wizard CD-ROM into your CD-ROM drive. The Setup Wizard should run automatically, and the Welcome screen should appear. If it does not, click the Start button and choose Run. In the field that appears, enter D:\setup.exe (if “D” is the letter of your CD-ROM drive). On the Welcome screen, you have the following choices:Click Here to Start- Click the Click Here to Start button to begin the software installation process. User Guide - Click the User Guide button to open the PDF file of this User Guide. Exit - Click the Exit button to exit the Setup Wizard.1. To install the Adapter, click the Click Here to Start button on the Welcome screen.2. After reading the License Agreement, click the Next button if you agree and want to continue the installation, or click the Cancel button to end the installation.3. Windows will begin copying the files onto your PC. Figure 3-1: Setup Wizard’s Welcome ScreenFigure 3-2: Setup Wizard’s License AgreementIMPORTANT: Do not connect the Adapter until you are instructed to do so or the setup will not work.
7Chapter 3: Setting up and Connecting the Wireless-G PCI Adapter with RangeBoosterConnecting the AdapterWireless-G PCI Adapter with RangeBoosterConnecting the Adapter 1. Before connecting the PCI Adapter to your PC, turn off your desktop PC and disconnect the power. 2. Open your PC case and locate an available PCI slot on the motherboard. Check with your computer manufacturer for instructions. 3. Slide the PCI Adapter into the PCI slot. Make sure that all of its pins are touching the slot's contacts. You may have to apply a bit of pressure to slide the adapter all the way in. After the adapter is firmly in place, secure its fastening tab to your PC's chassis with a mounting screw. Then, close your PC and re-connect the power. 4. Attach the external antennas to the adapter’s antenna ports. Bend the antennas up ninety degrees, then spread them apart ninety degrees, so they make a V or L shape.5. Power on your desktop PC. Setting up the AdapterThe next screen to appear will be the Available Wireless Network screen.This screen provides two options for setting up the Adapter.•Available Wireless Network. (For most users.) Use this option if you already have a network set up. The networks available to this Adapter will be listed on this screen. You can choose one of these networks and click the Connect button to connect to it. Click the Refresh button to update the Available Wireless Network list. •Manual Setup. If your network is not listed on this screen, select Manual Setup to set up the adapter manually. This method of setting up the Adapter is intended for Advanced Users only.The setup for each option is described, step by step, under the appropriate heading on the following pages.Click Exit to close the Setup Wizard, if you wish to set up the Adapter later.Figure 3-3: Connecting the AdapterFigure 3-4: Available Wireless Network
8Chapter 3: Setting up and Connecting the Wireless-G PCI Adapter with RangeBoosterSetting up the AdapterWireless-G PCI Adapter with RangeBoosterAvailable Wireless NetworkThe available networks are listed in the table on the center of the screen by SSID. Select the wireless network you wish to connect to and click the Connect button. (If you do not see your network listed, you can click the Refresh button to bring the list up again.) If the network utilizes wireless security, you will need to configure security on the Adapter. If not, you will be taken directly to the Congratulations screen.1. If you have wireless security enabled on your network, continue to step 2. If you don’t have wireless security enabled, continue to step 3. 2. Wireless Security - Your wireless security settings must match the wireless security settings on all other devices on your network.• If your network has the wireless security WEP (Wired Equivalent Privacy) enabled, this screen will appear. Select 64-bit or 128-bit.Then enter a passphrase or WEP key.Passphrase - Enter a passphrase in the Passphrase field, so a WEP key is automatically generated. The passphrase is case-sensitive and should not be longer than 16 alphanumeric characters. It must match the passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If you have any non-Linksys wireless products, enter the WEP key manually on those products.)WEP Key - The WEP key you enter must match the WEP key of your wireless network. For 64-bit encryption, enter exactly 10 hexadecimal characters. For 128-bit encryption, enter exactly 26 hexadecimal characters. Valid hexadecimal characters are “0” to “9” and “A” to “F”.Then click Connect and proceed to Step 3.• If your network has the wireless security WPA Personal (Wi-Fi Protected Access) enabled, this screen will appear. Encryption - Select the type of algorithm you want to use, TKIP or AES, from the Encryption drop-down menu.Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field. Then click Connect and proceed to Step 3.Figure 3-5: WEP Key Needed for ConnectionFigure 3-6: WPA - Personal Needed for Connectionencryption: encoding data transmitted in a network.wpa (wi-fi protected access: a wireless security protocol using TKIP (Temporal Key Integrity Protocol) encryption, which can be used in conjunction with a RADIUS server.wep (wired equivalent privacy): a method of encrypting network data transmitted on a wireless network for greater security.
9Chapter 3: Setting up and Connecting the Wireless-G PCI Adapter with RangeBoosterSetting up the AdapterWireless-G PCI Adapter with RangeBooster• If your network has the wireless security PSK2 (Pre-shared key 2) enabled, this screen will appear. Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field. Then click Connect and proceed to Step 3.3. After the software has been successfully installed, the Congratulations screen will appear. Click Connect to Network to connect to your network. For more information about the Wireless Network Monitor, refer to Chapter 4: Using the Wireless Network Monitor.Congratulations! The installation of the Wireless-G PCI Adapter is complete.To check the link information, search for available wireless networks, or make additional configuration changes, proceed to Chapter 4: Using the Wireless Network Monitor.Figure 3-7: PSK2 Needed for ConnectionFigure 3-8: Congratulations
10Chapter 3: Setting up and Connecting the Wireless-G PCI Adapter with RangeBoosterSetting up the AdapterWireless-G PCI Adapter with RangeBoosterManual SetupIf your network is not listed with the available networks, you can use Manual Setup. 1. Click Manual Setup on the Available Wireless Network screen to set up the adapter manually.2. The Network Settings screen from the Wireless Network Monitor will appear. If your network has a router or other DHCP server, click the radio button next to Obtain network settings automatically (DHCP).If your network does not have a DHCP server, click the radio button next to Specify network settings. Enter an IP Address, Subnet Mask, Default Gateway, and DNS addresses appropriate for your network. You must specify the IP Address and Subnet Mask on this screen. If you are unsure about the Default Gateway and DNS addresses, leave these fields empty. IP Address - This IP Address must be unique to your network.Subnet Mask - The Adapter’s Subnet Mask must be the same as your wired network’s Subnet Mask.Default Gateway - Enter the IP address of your network’s Gateway here. DNS 1 and DNS 2 - Enter the DNS address of your wired Ethernet network here.Click the Next button to continue, or click the Back button to return to the previous screen.3. The Wireless Mode screen shows a choice of two wireless modes. Click the Infrastructure Mode radio button if you want to connect to a wireless router or access point. Click the Ad-Hoc Mode radio button if you want to connect to another wireless device directly without using a wireless router or access point. Enter the SSID for your network.Infrastructure Mode - Use this mode if you want to connect to a wireless router or access point.Ad-Hoc Mode - Use this mode if you want to connect to another wireless device directly without using a wireless router or access point.SSID - This is the wireless network name that must be used for all the devices in your wireless network. It is case- sensitive and should be a unique name to help prevent others from entering your network.Click the Next button to continue, or click the Back button to return to the previous screen.Figure 3-9: Available Wireless NetworkFigure 3-11: Wireless ModeFigure 3-10: Network Settings
11Chapter 3: Setting up and Connecting the Wireless-G PCI Adapter with RangeBoosterSetting up the AdapterWireless-G PCI Adapter with RangeBooster4. If you chose Infrastructure Mode, go to Step 5 now. If you chose Ad-Hoc Mode, the Ad-Hoc Mode Settings screen will appear.Select the correct operating channel for your wireless network. The channel you choose should match the channel set on the other devices in your wireless network. If you are unsure about which channel to use, keep the default setting.Click the Next button. Click the Back button to change any settings.5. If your wireless network doesn’t have wireless security, select Disabled and then click the Next button to continue. Proceed to Step 6.If your wireless network has wireless security, select the method of security used by the other devices on your network: WEP, WPA-Personal, PSK2, WPA-Enterprise, or RADIUS. WEP stands for Wired Equivalent Privacy, and WPA stands for Wi-Fi Protected Access. PSK2 stands for Pre-shared Key2. WPA is a stronger security method than WEP. RADIUS stands for Remote Authentication Dial-In User Service. Click the Next button to continue or the Back button to return to the previous screen. Proceed to the appropriate section for your security method: WEP, WPA-Personal, PSK2, WPA-Enterprise, or RADIUS.WEPWEP - Select 64-bit or 128-bit encryption Passphrase - Enter a passphrase in the Passphrase field, so a WEP key is automatically generated. It is case-sensitive and should not be longer than 16 alphanumeric characters. This passphrase must match the passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If you have any non-Linksys wireless products, enter the WEP key manually on those products.)WEP Key - The WEP key you enter must match the WEP key of your wireless network. For 64-bit encryption, enter exactly 10 hexadecimal characters. For 128-bit encryption, enter exactly 26 hexadecimal characters. Valid hexadecimal characters are “0” to “9” and “A” to “F”.Advanced UsersTX Key - The default transmit key number is 1. If your network’s access point or wireless router uses transmit key number 2, 3, or 4, select the appropriate number from the TX Key drop-down box. Figure 3-13: Wireless Security - WEPFigure 3-12: Ad-Hoc Mode Settings
12Chapter 3: Setting up and Connecting the Wireless-G PCI Adapter with RangeBoosterSetting up the AdapterWireless-G PCI Adapter with RangeBoosterAuthentication -The default is set to Auto, so it will auto-detect for Shared Key or Open System authentication. For Shared Key authentication, both the sender and the recipient share a WEP key for authentication. For Open System authentication, the sender and the recipient do not share a WEP key for authentication. If you are not sure which authentication method to select, keep the default, Auto.Click the Next button to continue, or click the Back button to return to the previous screen.WPA PersonalWPA Personal offers two encryption methods, TKIP and AES, with dynamic encryption keys. Select TKIP or AES for encryption. Then enter a Passphrase that is 8-63 characters in length.Encryption - Select the type of algorithm you want to use, TKIP or AES, from the Encryption drop-down menu.Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field. Click the Next button to continue or the Back button to return to the previous screen.PSK2Enter a Passphrase that is 8-63 characters in length.Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field. Click the Next button to continue or the Back button to return to the previous screen.Figure 3-14: Wireless Security - WPA PersonalFigure 3-1: Wireless Security - PSK2
13Chapter 3: Setting up and Connecting the Wireless-G PCI Adapter with RangeBoosterSetting up the AdapterWireless-G PCI Adapter with RangeBoosterWPA EnterpriseWPA Enterprise features WPA security used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.) WPA Enterprise offers two authentication methods, EAP-TLS and PEAP, as well as two encryption methods, TKIP and AES, with dynamic encryption keys.Authentication - Select the authentication method your network is using, EAP-TLS or PEAP.EAP-TLSIf you selected EAP-TLS, enter the login name of your wireless network in the Login Name field. Enter the name of the authentication server in the Server Name field (this is optional). From the Certificate drop-down menu, select the certificate you have installed to authenticate you on your wireless network. Select the type of encryption, TKIP or AES, from the Encryption drop-down menu.Click the Next button to continue or the Back button to return to the previous screen.PEAPIf you selected PEAP, enter the login name of your wireless network in the Login Name field. Enter the password of your wireless network in the Password field. Enter the name of the authentication server in the Server Name field (this is optional). From the Certificate drop-down menu, select the certificate you have installed to authenticate you on your wireless network; if you want to use any certificate, keep the default setting, Trust Any. Then select the authentication method used inside the PEAP tunnel. Select the type of encryption, TKIP or AES, from the Encryption drop-down menu.Click the Next button to continue or the Back button to return to the previous screen.Figure 3-16: Wireless Security - WPA Enterprise - PEAPFigure 3-15: Wireless Security - WPA Enterprise - EAP-TLS
14Chapter 3: Setting up and Connecting the Wireless-G PCI Adapter with RangeBoosterSetting up the AdapterWireless-G PCI Adapter with RangeBoosterRADIUSRADIUS features use of a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.) RADIUS offers two authentication types: EAP-TLS and PEAP.Authentication - Select the authentication method your network is using, EAP-TLS or PEAP.EAP-TLSIf you selected EAP-TLS, enter the login name of your wireless network in the Login Name field. Enter the name of the authentication server in the Server Name field (this is optional). From the Certificate drop-down menu, select the certificate you have installed to authenticate you on your wireless network.Click the Next button to continue or the Back button to return to the previous screen.PEAPIf you selected PEAP, enter the login name of your wireless network in the Login Name field. Enter the password of your wireless network in the Password field. Enter the name of the authentication server in the Server Name field (this is optional). From the Certificate drop-down menu, select the certificate you have installed to authenticate you on your wireless network; if you want to use any certificate, keep the default setting, Trust Any. Then select the authentication method used inside the PEAP tunnel.Click the Next button to continue or the Back button to return to the previous screen.Figure 3-17: Wireless Security - RADIUS - EAP-TLSFigure 3-18: Wireless Security - RADIUS - PEAP
15Chapter 3: Setting up and Connecting the Wireless-G PCI Adapter with RangeBoosterSetting up the AdapterWireless-G PCI Adapter with RangeBooster6. The Confirm New Settings screen will appear next and show the new settings. To save the new settings, click the Save button. To edit the new settings, click the Back button. To exit the Manual Setup through the Wireless Network Monitor, click Exit.7. The Congratulations screen will appear next. Click Connect to Network to implement the new settings and return to the Link Information screen. Click Return to Profiles screen to return to the Profiles screen.Congratulations! Your manual setup through the Wireless Network Monitor is complete.To check the link information, search for available wireless networks, or make additional configuration changes, proceed to Chapter 4: Using the Wireless Network Monitor.Figure 3-19: Confirm New SettingsFigure 3-20: Congratulations screen
16Chapter 4: Using the Wireless Network MonitorAccessing the Wireless Network MonitorWireless-G PCI Adapter with RangeBoosterChapter 4: Using the Wireless Network MonitorUse the Wireless Network Monitor to check the link information, search for available wireless networks, or create profiles that hold different configuration settings.Accessing the Wireless Network MonitorAfter installing the Adapter, the Wireless Network Monitor icon will appear in the system tray of your computer. If the Wireless Network Monitor is enabled, then the icon will be green. If the Wireless Network Monitor is disabled or the Adapter is not connected, then the icon will be gray.Using the Wireless Network MonitorThe opening screen of the Wireless Network Monitor is the Link Information screen. From this screen, you can find out how strong the current wireless signal is and how good the connection’s quality is. You can also click the More Information button to view additional status information about the current wireless connection. To search for available wireless networks, click the Site Survey tab. To perform configuration changes or create connection profiles, click the Profiles tab.Link InformationThe Link Information screen displays network mode, signal strength, and link quality information about the current connection. It also provides a button to click for additional status information.Ad-Hoc Mode or Infrastructure Mode - The screen indicates whether the Adapter is currently working in ad-hoc or infrastructure mode.Signal Strength - The Signal Strength bar indicates signal strength. Link Quality - The Link Quality bar indicates the quality of the wireless network connection.Click the More Information button to view additional information about the wireless network connection on the Wireless Network Status screen.Figure 4-1: Wireless Network Monitor IconFigure 4-2: Link Information
17Chapter 4: Using the Wireless Network MonitorLink InformationWireless-G PCI Adapter with RangeBoosterWireless Network StatusThe Wireless Network Status screen provides information on your current network settings.Status - This shows the status of the wireless network connection.SSID - This is the unique name of the wireless network. Wireless Mode - The mode of the wireless network currently in use is displayed here.Transfer Rate - The data transfer rate of the current connection is shown here.Channel - This is the channel to which the wireless network devices are set. Security - The status of the wireless security feature is displayed here.Authentication - This is your wireless network’s authentication method.IP Address - The IP Address of the Adapter is displayed here.Subnet Mask - The Subnet Mask of the Adapter is shown here.Default Gateway - The Default Gateway address of the Adapter is displayed here.DNS - This is the DNS address of the Adapter.DHCP Client - This displays the Adapter’s status as a DHCP client.MAC Address- The MAC address of the wireless network’s access point or wireless router is shown here.Signal Strength - The Signal Strength bar indicates the signal strength. Link Quality - The Link Quality bar indicates the quality of the wireless network connection.Click the Statistics button to go to the Wireless Network Statistics screen. Click the Back button to return to the initial Link Information screen. Click the Save to Profile button to save the currently active connection settings to a profile.Figure 4-3: More Information - Wireless Network Status
18Chapter 4: Using the Wireless Network MonitorLink InformationWireless-G PCI Adapter with RangeBoosterWireless Network StatisticsThe Wireless Networks Statistics screen provides statistics on your current network settings.Transmit Rate - This is the data transfer rate of the current connection. (In Auto mode, the Adapter dynamically shifts to the fastest data transfer rate possible at any given time.)Receive Rate - This is the rate at which data is received.Packets Received - This shows the packets received by the Adapter, in real time, since connecting to the wireless network or since the Refresh Statistics button was last pressed.Packets Transmitted - This shows the packets transmitted from the Adapter, in real time, since connecting to the wireless network or since the Refresh Statistics button was last pressed.Bytes Received - This shows the bytes received by the Adapter, in real time, since connecting to the wireless network or since the Refresh Statistics button was last pressed.Bytes Transmitted - This shows the bytes transmitted by the Adapter, in real time, since connecting to the wireless network or since the Refresh Statistics button was last pressed.Driver Version - This shows the version of the Adapter’s driver.Noise Level - This shows the level of background noise affecting the wireless signal. A lower reading translates into a higher quality signal.Signal Strength - This is the intensity of the wireless signal received by the Adapter.Transmit Power - This is the power output at which the Adapter is transmitting.Up Time - This indicates the length of the most recent connection to a wireless network.Total Up Time - This indicates the cumulative total of the Adapter’s connection time.Signal Strength - The Signal Strength bar indicates the signal strength. Link Quality - The Link Quality bar indicates the quality of the wireless network connection.Click the Back button to return to the initial Link Information screen. Click the Status button to go to the Wireless Network Status screen. Click the Save to Profile button to save the currently active connection settings to a profile. Click the Refresh button to reset the statistics.Figure 4-4: More Information-Network Statistics
19Chapter 4: Using the Wireless Network MonitorSite SurveyWireless-G PCI Adapter with RangeBoosterSite SurveyThe Site Survey screen displays a list of available networks in the table on the left. The table shows each network’s SSID, Channel, and the quality of the wireless signal the Adapter is receiving. You may click SSID, CH (Channel), or Signal, to sort by that field.SSID - The SSID or unique name of the wireless network is displayed here.CH - This is the channel that the network uses.Signal - This is the percentage of signal strength, from 0 to 100%.Site InformationFor each network selected, the following settings are listed:SSID - This the SSID or unique name of the wireless network. Wireless Mode - This is the mode of the wireless network currently in use.Channel - This is the channel to which the wireless network devices are set. Security - The status of the wireless security feature is displayed here.MAC Address- The MAC address of the wireless network’s access point is displayed here.Refresh - Click the Refresh button to perform a new search for wireless devices.Connect - To connect to one of the networks on the list, select the wireless network, and click the Connect button. If the network has security enabled, then you will see one of the wireless security screens in the next paragraph.Wireless Security - Your wireless security settings must match the wireless security settings on all other devices on your network.• If your network has the wireless security WEP (Wired Equivalent Privacy) enabled, this screen will appear. Select 64-bit or 128-bit.Then enter a passphrase or WEP key.Passphrase - Enter a passphrase in the Passphrase field, so a WEP key is automatically generated. The passphrase is case-sensitive and should not be longer than 16 alphanumeric characters. It must match Figure 4-5: Site SurveyFigure 4-6: WEP Key Needed for Connection
20Chapter 4: Using the Wireless Network MonitorSite SurveyWireless-G PCI Adapter with RangeBoosterthe passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If you have any non-Linksys wireless products, enter the WEP key manually on those products.)WEP Key - The WEP key you enter must match the WEP key of your wireless network. For 64-bit encryption, enter exactly 10 hexadecimal characters. For 128-bit encryption, enter exactly 26 hexadecimal characters. Valid hexadecimal characters are “0” to “9” and “A” to “F”.Then click Connect.• If your network has the wireless security WPA Personal (Wi-Fi Protected Access) enabled, this screen will appear. Encryption - Select the type of algorithm you want to use, TKIP or AES, from the Encryption drop-down menu.Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field. Then click Connect.• If your network has the wireless security PSK2 (Pre-shared key 2) enabled, this screen will appear. Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field. Then click Connect.Figure 4-7: WPA-Personal Needed for ConnectionFigure 4-8: PSK2 Needed for Connection
21Chapter 4: Using the Wireless Network MonitorProfilesWireless-G PCI Adapter with RangeBoosterProfilesThe Profiles screen lets you save different configuration profiles for different network setups. The table on the left displays a list of available profiles with their profile names and SSIDs.Profile - The name of the profile is displayed here.SSID - The SSID or unique name of the wireless network is displayed here.Profile InformationFor each profile selected, the following are listed:Wireless Mode - This is the mode of the wireless network currently in use.Transfer Rate - The data transfer rate of the current connection is shown here.Channel - This is the channel to which the wireless network devices are set. Security - The status of the wireless security feature is displayed here.Authentication - The authentication setting for the network is shown here.Connect - To connect to a wireless network using a specific profile, select the profile, and click Connect.New - Click the New button to create a new profile. See the next section, “Creating a New Profile,” for detailed instructions.Edit - Select the profile you want to change, and then click the Edit button. Import - Click the Import button to import a profile that has been saved in another location. Select the appropriate file, and click the Open button.Export - Select the profile you want to save in a different location, and click the Export button. Direct Windows to the appropriate folder, and click the Save button.Delete - Select the profile you want to delete, and then click the Delete button. Figure 4-9: ProfilesFigure 4-10: Import a ProfileFigure 4-11: Export a ProfileNOTE: If you want to export more than one profile, you have to export them one at a time.
22Chapter 4: Using the Wireless Network MonitorCreate a New ProfileWireless-G PCI Adapter with RangeBoosterCreate a New ProfileThe next screen to appear will be the Available Wireless Network screen.This screen provides two options for setting up the Adapter.•Available Wireless Network. (For most users.) Use this option if you already have a network set up. The networks available to this Adapter will be listed on this screen. You can choose one of these networks and click the Connect button to connect to it. Click the Refresh button to update the Available Wireless Network list. •Manual Setup. If your network is not listed on this screen, select Manual Setup to set up the adapter manually. This method of setting up the Adapter is intended for Advanced Users only.The setup for each option is described, step by step, under the appropriate heading on the following pages.Click Exit to close the Setup Wizard, if you wish to set up the Adapter later.Available Wireless NetworkThe available networks are listed in the table on the center of the screen by SSID. Select the wireless network you wish to connect to and click the Connect button. (If you do not see your network listed, you can click the Refresh button to bring the list up again.) If the network utilizes wireless security, you will need to configure security on the Adapter. If not, you will be taken directly to the Congratulations screen.1. If you have wireless security enabled on your network, continue to step 2. If you don’t have wireless security enabled, continue to step 3. 2. Wireless Security - Your wireless security settings must match the wireless security settings on all other devices on your network.• If your network has the wireless security WEP (Wired Equivalent Privacy) enabled, this screen will appear. Select 64-bit or 128-bit.Then enter a passphrase or WEP key.Passphrase - Enter a passphrase in the Passphrase field, so a WEP key is automatically generated. The passphrase is case-sensitive and should not be longer than 16 alphanumeric characters. It must match the passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If you have any non-Linksys wireless products, enter the WEP key manually on those products.)Figure 4-12: Create a New ProfileFigure 4-1: WEP Key Needed for Connection
23Chapter 4: Using the Wireless Network MonitorCreate a New ProfileWireless-G PCI Adapter with RangeBoosterWEP Key - The WEP key you enter must match the WEP key of your wireless network. For 64-bit encryption, enter exactly 10 hexadecimal characters. For 128-bit encryption, enter exactly 26 hexadecimal characters. Valid hexadecimal characters are “0” to “9” and “A” to “F”.Then click Connect and proceed to Step 3.• If your network has the wireless security WPA Personal (Wi-Fi Protected Access) enabled, this screen will appear. Encryption - Select the type of algorithm you want to use, TKIP or AES, from the Encryption drop-down menu.Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field. Then click Connect and proceed to Step 3.• If your network has the wireless security PSK2 (Pre-shared key 2) enabled, this screen will appear. Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field. Then click Connect and proceed to Step 3.3. After the software has been successfully installed, the Congratulations screen will appear. Click Connect to Network to connect to your network, implement the new settings, and return to the Link Information screen. Congratulations! The profile has been successfully configured.Figure 4-2: WPA - Personal Needed for ConnectionFigure 4-3: PSK2 Needed for ConnectionFigure 4-4: Congratulations
24Chapter 4: Using the Wireless Network MonitorCreate a New ProfileWireless-G PCI Adapter with RangeBoosterManual SetupIf your network is not listed with the available networks, you can use Manual Setup. 1. Click Manual Setup on the Available Wireless Network screen to set up the adapter manually.2. The Network Settings screen from the Wireless Network Monitor will appear. If your network has a router or other DHCP server, click the radio button next to Obtain network settings automatically (DHCP).If your network does not have a DHCP server, click the radio button next to Specify network settings. Enter an IP Address, Subnet Mask, Default Gateway, and DNS addresses appropriate for your network. You must specify the IP Address and Subnet Mask on this screen. If you are unsure about the Default Gateway and DNS addresses, leave these fields empty. IP Address - This IP Address must be unique to your network.Subnet Mask - The Adapter’s Subnet Mask must be the same as your wired network’s Subnet Mask.Default Gateway - Enter the IP address of your network’s Gateway here. DNS 1 and DNS 2 - Enter the DNS address of your wired Ethernet network here.Click the Next button to continue, or click the Back button to return to the previous screen.Figure 4-13: Available Wireless NetworkFigure 4-14: Network Settings
25Chapter 4: Using the Wireless Network MonitorCreate a New ProfileWireless-G PCI Adapter with RangeBooster3. The Wireless Mode screen shows a choice of two wireless modes. Click the Infrastructure Mode radio button if you want to connect to a wireless router or access point. Click the Ad-Hoc Mode radio button if you want to connect to another wireless device directly without using a wireless router or access point. Enter the SSID for your network.Infrastructure Mode - Use this mode if you want to connect to a wireless router or access point.Ad-Hoc Mode - Use this mode if you want to connect to another wireless device directly without using a wireless router or access point.SSID - This is the wireless network name that must be used for all the devices in your wireless network. It is case- sensitive and should be a unique name to help prevent others from entering your network.Click the Next button to continue, or click the Back button to return to the previous screen.4. If you chose Infrastructure Mode, go to Step 5 now. If you chose Ad-Hoc Mode, the Ad-Hoc Mode Settings screen will appear.Select the correct operating channel for your wireless network. The channel you choose should match the channel set on the other devices in your wireless network. If you are unsure about which channel to use, keep the default setting.Click the Next button. Click the Back button to change any settings.5. If your wireless network doesn’t have wireless security, select Disabled and then click the Next button to continue. Proceed to Step 6.If your wireless network has wireless security, select the method of security used by the other devices on your network: WEP, WPA-Personal, WPA-Enterprise, PSK2, or RADIUS. WEP stands for Wired Equivalent Privacy, and WPA stands for Wi-Fi Protected Access. WPA is a stronger security method than WEP. RADIUS stands for Remote Authentication Dial-In User Service. PSK2 stands for Pre-shared Key 2. Click the Next button to continue or the Back button to return to the previous screen. Proceed to the appropriate section for your security method: WEP, WPA-Personal, PSK2, WPA-Enterprise, or RADIUS.Figure 4-15: Wireless ModeFigure 4-16: Ad-Hoc Mode Settingsencryption: encoding data transmitted in a network.wpa (wi-fi protected access: a wireless security protocol using TKIP (Temporal Key Integrity Protocol) encryption, which can be used in conjunction with a RADIUS server.wep (wired equivalent privacy): a method of encrypting network data transmitted on a wireless network for greater security.
26Chapter 4: Using the Wireless Network MonitorCreate a New ProfileWireless-G PCI Adapter with RangeBoosterWEPWEP - Select 64-bit or 128-bit encryption Passphrase - Enter a passphrase in the Passphrase field, so a WEP key is automatically generated. It is case-sensitive and should not be longer than 16 alphanumeric characters. This passphrase must match the passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If you have any non-Linksys wireless products, enter the WEP key manually on those products.)WEP Key - The WEP key you enter must match the WEP key of your wireless network. For 64-bit encryption, enter exactly 10 hexadecimal characters. For 128-bit encryption, enter exactly 26 hexadecimal characters. Valid hexadecimal characters are “0” to “9” and “A” to “F”.Advanced UsersTX Key - The default transmit key number is 1. If your network’s access point or wireless router uses transmit key number 2, 3, or 4, select the appropriate number from the TX Key drop-down box.Authentication -The default is set to Auto, so it will auto-detect for Shared Key or Open System authentication. For Shared Key authentication, both the sender and the recipient share a WEP key for authentication. For Open System authentication, the sender and the recipient do not share a WEP key for authentication. If you are not sure which authentication method to select, keep the default, Auto.Click the Next button to continue, or click the Back button to return to the previous screen.WPA PersonalWPA Personal offers two encryption methods, TKIP and AES, with dynamic encryption keys. Select TKIP or AES for encryption. Then enter a Passphrase that is 8-63 characters in length.Encryption - Select the type of algorithm you want to use, TKIP or AES, from the Encryption drop-down menu.Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field. Click the Next button to continue or the Back button to return to the previous screen. Figure 4-18: Wireless Security - WPA PersonalFigure 4-17: Wireless Security - WEP
27Chapter 4: Using the Wireless Network MonitorCreate a New ProfileWireless-G PCI Adapter with RangeBoosterPSK2Enter a Passphrase that is 8-63 characters in length.Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field. Click the Next button to continue or the Back button to return to the previous screen.Figure 4-19: Wireless Security - PSK2
28Chapter 4: Using the Wireless Network MonitorCreate a New ProfileWireless-G PCI Adapter with RangeBoosterWPA EnterpriseWPA Enterprise features WPA security used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.) WPA Enterprise offers two authentication methods, EAP-TLS and PEAP, as well as two encryption methods, TKIP and AES, with dynamic encryption keys.Authentication - Select the authentication method your network is using, EAP-TLS or PEAP.EAP-TLSIf you selected EAP-TLS, enter the login name of your wireless network in the Login Name field. Enter the name of the authentication server in the Server Name field (this is optional). From the Certificate drop-down menu, select the certificate you have installed to authenticate you on your wireless network. Select the type of encryption, TKIP or AES, from the Encryption drop-down menu.Click the Next button to continue or the Back button to return to the previous screen.PEAPIf you selected PEAP, enter the login name of your wireless network in the Login Name field. Enter the password of your wireless network in the Password field. Enter the name of the authentication server in the Server Name field (this is optional). From the Certificate drop-down menu, select the certificate you have installed to authenticate you on your wireless network; if you want to use any certificate, keep the default setting, Trust Any. Then select the authentication method used inside the PEAP tunnel. Select the type of encryption, TKIP or AES, from the Encryption drop-down menu.Click the Next button to continue or the Back button to return to the previous screen.Figure 4-20: Wireless Security - WPA Enterprise Using EAP-TLSFigure 4-21: Wireless Security - WPA Enterprise Using PEAP
29Chapter 4: Using the Wireless Network MonitorCreate a New ProfileWireless-G PCI Adapter with RangeBoosterRADIUSRADIUS features use of a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.) RADIUS offers two authentication types: EAP-TLS and PEAP.Authentication - Select the authentication method your network is using, EAP-TLS or PEAP.EAP-TLSIf you selected EAP-TLS, enter the login name of your wireless network in the Login Name field. Enter the name of the authentication server in the Server Name field (this is optional). From the Certificate drop-down menu, select the certificate you have installed to authenticate you on your wireless network.Click the Next button to continue or the Back button to return to the previous screen.PEAPIf you selected PEAP, enter the login name of your wireless network in the Login Name field. Enter the password of your wireless network in the Password field. Enter the name of the authentication server in the Server Name field (this is optional). From the Certificate drop-down menu, select the certificate you have installed to authenticate you on your wireless network; if you want to use any certificate, keep the default setting, Trust Any. Then select the authentication method used inside the PEAP tunnel.Click the Next button to continue or the Back button to return to the previous screen.Figure 4-22: Wireless Security - RADIUS Using EAP-TLS Figure 4-23: Wireless Security - RADIUS Using PEAP
30Chapter 4: Using the Wireless Network MonitorCreate a New ProfileWireless-G PCI Adapter with RangeBooster6. The Confirm New Settings screen will appear next and show the new settings. To save the new settings, click the Save button. To edit the new settings, click the Back button. To exit the Manual Setup through the Wireless Network Monitor, click Exit.7. The Congratulations screen will appear next. Click Connect to Network to implement the new settings immediately and return to the Link Information screen. Click Return to Profiles Screen to keep the current settings active and return to the Profiles screen.Congratulations! The profile has been successfully configured.Figure 4-24: Confirm New Settings for New ProfileFigure 4-25: Congratulations
30Appendix A: TroubleshootingCommon Problems and SolutionsWireless-G PCI Adapter with RangeBoosterAppendix A: TroubleshootingThis appendix consists of two parts: “Common Problems and Solutions” and “Frequently Asked Questions.” This appendix provides solutions to problems that may occur during the installation and operation of the Wireless-G PCI Adapter with RangeBooster. Read the description below to solve your problems. If you can't find an answer here, check the Linksys website at www.linksys.com.Common Problems and Solutions1. The Wireless-G PCI Adapter with RangeBooster does not work properly.• Reinsert the Wireless-G PCI Adapter with RangeBooster into your PC’s PCI slot.• Right click on My Computer and select Properties. Select the device manager and click on the Network Adapter. You will find the Wireless-G PCI Adapter with RangeBooster if it is installed successfully. If you see the yellow exclamation mark, the resources are conflicting. You will see the status of the Wireless-G PCI Adapter with RangeBooster. If there is a yellow question mark, please check the following:• Make sure that your PC has a free IRQ (Interrupt ReQuest, a hardware interrupt on a PC.) • Make sure that you have inserted the right adapter and installed the proper driver.If the Wireless-G PCI Adapter with RangeBooster does not function after attempting the above steps, remove the adapter and do the following:• Uninstall the driver software from your PC.• Restart your PC and repeat the hardware and software installation as specified in this User Guide.2. I cannot communicate with the other computers linked via Ethernet in the Infrastructure configuration.• Make sure that the PC to which the Wireless-G PCI Adapter with RangeBooster is associated is powered on.• Make sure that your Wireless-G PCI Adapter with RangeBooster is configured on the same channel and with the same security options as with the other computers in the Infrastructure configuration.
31Appendix A: TroubleshootingFrequently Asked QuestionsWireless-G PCI Adapter with RangeBoosterFrequently Asked QuestionsCan I run an application from a remote computer over the wireless network?This will depend on whether or not the application is designed to be used over a network. Consult the application’s user guide to determine if it supports operation over a network.Can I play computer games with other members of the wireless network?Yes, as long as the game supports multiple players over a LAN (local area network). Refer to the game’s user guide for more information.What is the IEEE 802.11b standard?It is one of the IEEE standards for wireless networks. The 802.11b standard allows wireless networking hardware from different manufacturers to communicate, provided that the hardware complies with the 802.11b standard. The 802.11b standard states a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz.What is the IEEE 802.11g standard?It is one of the IEEE standards for wireless networks. The 802.11g standard allows wireless networking hardware from different manufacturers to communicate, provided that the hardware complies with the 802.11g standard. The 802.11g standard states a maximum data transfer rate of 54Mbps and an operating frequency of 2.4GHz.What IEEE 802.11b features are supported?The product supports the following IEEE 802.11b functions: • CSMA/CA plus Acknowledge protocol • Multi-Channel Roaming • Automatic Rate Selection • RTS/CTS feature • Fragmentation • Power Management •What IEEE 802.11g features are supported?The product supports the following IEEE 802.11g functions: • CSMA/CA plus Acknowledge protocol • OFDM protocol• Multi-Channel Roaming • Automatic Rate Selection • RTS/CTS feature • Fragmentation• Power Management
32Appendix A: TroubleshootingFrequently Asked QuestionsWireless-G PCI Adapter with RangeBoosterWhat is ad-hoc mode?When a wireless network is set to ad-hoc mode, the wireless-equipped computers are configured to communicate directly with each other. The ad-hoc wireless network will not communicate with any wired network. What is infrastructure mode?When a wireless network is set to infrastructure mode, the wireless network is configured to communicate with a wired network through a wireless access point.What is roaming?Roaming is the ability of a portable computer user to communicate continuously while moving freely throughout an area greater than that covered by a single access point. Before using the roaming function, the workstation must make sure that it is the same channel number with the access point of dedicated coverage area. To achieve true seamless connectivity, the wireless LAN must incorporate a number of different functions. Each node and access point, for example, must always acknowledge receipt of each message. Each node must maintain contact with the wireless network even when not actually transmitting data. Achieving these functions simultaneously requires a dynamic RF networking technology that links access points and nodes. In such a system, the user’s end node undertakes a search for the best possible access to the system. First, it evaluates such factors as signal strength and quality, as well as the message load currently being carried by each access point and the distance of each access point to the wired backbone. Based on that information, the node next selects the right access point and registers its address. Communications between end node and host computer can then be transmitted up and down the backbone.As the user moves on, the end node’s RF transmitter regularly checks the system to determine whether it is in touch with the original access point or whether it should seek a new one. When a node no longer receives acknowledgment from its original access point, it undertakes a new search. Upon finding a new access point, it then re-registers, and the communication process continues.What is ISM band?The FCC and their counterparts outside of the U.S. have set aside bandwidth for unlicensed use in the ISM (Industrial, Scientific and Medical) band. Spectrum in the vicinity of 2.4 GHz, in particular, is being made available worldwide. This presents a truly revolutionary opportunity to place convenient high-speed wireless capabilities in the hands of users around the globe. What is Spread Spectrum?Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for
33Appendix A: TroubleshootingFrequently Asked QuestionsWireless-G PCI Adapter with RangeBoosterreliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade-off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum (DSSS) and Frequency Hopping Spread Spectrum (FHSS).What is DSSS? What is FHSS? And what are their differences?Frequency-Hopping Spread-Spectrum (FHSS) uses a narrowband carrier that changes frequency in a pattern that is known to both transmitter and receiver. Properly synchronized, the net effect is to maintain a single logical channel. To an unintended receiver, FHSS appears to be short-duration impulse noise. Direct-Sequence Spread-Spectrum (DSSS) generates a redundant bit pattern for each bit to be transmitted. This bit pattern is called a chip (or chipping code). The longer the chip, the greater the probability that the original data can be recovered. Even if one or more bits in the chip are damaged during transmission, statistical techniques embedded in the radio can recover the original data without the need for retransmission. To an unintended receiver, DSSS appears as low power wideband noise and is rejected (ignored) by most narrowband receivers. Would the information be intercepted while transmitting on air?The Adapter features two-fold protection in security. On the hardware side, as with Direct Sequence Spread Spectrum technology, it has the inherent security feature of scrambling. On the software side, the Adapter offers the encryption function (WEP) to enhance security and access control.What is WEP?WEP is Wired Equivalent Privacy, a data privacy mechanism based on a shared key algorithm, as described in the IEEE 802.11 standard. For more information, refer to “Appendix C: Wireless Security.”What is WPA?WPA is Wi-Fi Protected Access, a wireless security protocol that can be used in conjunction with a RADIUS server. For more information, refer to “Appendix C: Wireless Security.”What is RADIUS?RADIUS is Remote Authentication Dial-In User Service, which uses an authentication server to control network access. For more information, refer to “Appendix C: Wireless Security.”
34Appendix B: Using Windows XP Wireless ConfigurationWireless-G PCI Adapter with RangeBoosterAppendix B: Using Windows XP Wireless ConfigurationIf your computer is running Windows XP, then this choice will be available. If you want to use Windows XP Wireless Configuration to control the Adapter, instead of using the Wireless Network Monitor, then right-click on the Wireless Network Monitor and select Use Windows XP Wireless Configuration. If you want to switch back to the Wireless Network Monitor, right-click the Wireless Network Monitor icon, and select Use Linksys Wireless Network Monitor.1. After installing the Adapter, the Windows XP Wireless Configuration icon will appear in your computer’s system tray. Double-click the icon. Figure B-1: Wireless Network Monitor IconFigure B-2: Windows XP - Use Windows XP Wireless ConfigurationNOTE: For more information about Windows XP Wireless Configuration, refer to Windows Help.Figure B-3: Windows XP Wireless Configuration Icon
35Appendix B: Using Windows XP Wireless ConfigurationWireless-G PCI Adapter with RangeBooster2. The screen that appears will show any available wireless network. Select the network you want. Click the Connect button.If your network does not have wireless security enabled, go to step 3.If your network does have wireless security enabled, go to step 4.3. If your network does not have wireless security enabled, click the Connect Anyway button to connect the Adapter to your network.NOTE: Steps 2 and 3 are the instructions and screenshots for Windows XP with Service Pack 2 installed.Figure B-4: Available Wireless NetworkFigure B-5: No Wireless Security
36Appendix B: Using Windows XP Wireless ConfigurationWireless-G PCI Adapter with RangeBooster4. If your network uses wireless security WEP, enter the WEP Key used into the Network Key and Confirm network key fields. If your network uses wireless security WPA Personal, enter the Passphrase used into the Network Key and Confirm network key fields. Click the Connect button.5. Your wireless network will appear as Connected when your connection is active.For more information about wireless networking on a Windows XP computer, click the Start button, select Help, and choose Support. Enter the keyword wireless in the field provided, and press the Enter key.The installation of the Windows XP Wireless Configuration is complete.NOTE: Windows XP Wireless Configuration does not support the use of a passphrase. Enter the exact WEP key used by your wireless router or access point.Figure B-6: Network Connection - Wireless SecurityFigure B-7: Wireless Network Connection
37Appendix C: Wireless SecuritySecurity PrecautionsWireless-G PCI Adapter with RangeBoosterAppendix C: Wireless SecurityLinksys wants to make wireless networking as safe and easy for you as possible. The current generation of Linksys products provide several network security features, but they require specific action on your part for implementation. So, keep the following in mind whenever you are setting up or using your wireless network.Security PrecautionsThe following is a complete list of security precautions to take (at least steps 1 through 5 should be followed):1. Change the default SSID. 2. Disable SSID Broadcast. 3. Change the default password for the Administrator account. 4. Enable MAC Address Filtering. 5. Change the SSID periodically. 6. Use the highest encryption algorithm possible. Use WPA if it is available. Please note that this may reduce your network performance. 7. Change the WEP encryption keys periodically. Security Threats Facing Wireless Networks Wireless networks are easy to find. Hackers know that in order to join a wireless network, wireless networking products first listen for “beacon messages”. These messages can be easily decrypted and contain much of the network’s information, such as the network’s SSID (Service Set Identifier). Here are the steps you can take:Change the administrator’s password regularly. With every wireless networking device you use, keep in mind that network settings (SSID, WEP keys, etc.) are stored in its firmware. Your network administrator is the only person who can change network settings. If a hacker gets a hold of the administrator’s password, he, too, can change those settings. So, make it harder for a hacker to get that information. Change the administrator’s password regularly.SSID. There are several things to keep in mind about the SSID: Note: Some of these security features are available only through the network router or access point. Refer to the router or access point’s documentation for more information.
38Appendix C: Wireless SecuritySecurity Threats Facing Wireless NetworksWireless-G PCI Adapter with RangeBooster1. Disable Broadcast 2. Make it unique 3. Change it often Most wireless networking devices will give you the option of broadcasting the SSID. While this option may be more convenient, it allows anyone to log into your wireless network. This includes hackers. So, don’t broadcast the SSID.Wireless networking products come with a default SSID set by the factory. (The Linksys default SSID is “linksys”.) Hackers know these defaults and can check these against your network. Change your SSID to something unique and not something related to your company or the networking products you use.Change your SSID regularly so that any hackers who have gained access to your wireless network will have to start from the beginning in trying to break in.MAC Addresses. Enable MAC Address filtering. MAC Address filtering will allow you to provide access to only those wireless nodes with certain MAC Addresses. This makes it harder for a hacker to access your network with a random MAC Address. WEP Encryption. Wired Equivalent Privacy (WEP) is often looked upon as a cure-all for wireless security concerns. This is overstating WEP’s ability. Again, this can only provide enough security to make a hacker’s job more difficult.There are several ways that WEP can be maximized:1. Use the highest level of encryption possible 2. Use “Shared Key” authentication3. Change your WEP key regularly WPA. Wi-Fi Protected Access (WPA) is the newest and best available standard in Wi-Fi security. Three modes are available: WPA-Personal, WPA Radius, and Radius. Radius-PSK gives you a choice of two encryption methods: TKIP (Temporal Key Integrity Protocol), which utilizes a stronger encryption method and incorporates Message Integrity Code (MIC) to provide protection against hackers, and AES (Advanced Encryption System), which utilizes a symmetric 128-Bit block data encryption. WPA RADIUS offers two encryption methods, TKIP and AES, with dynamic encryption keys. RADIUS (Remote Authentication Dial-In User Service) utilizes a RADIUS server for authentication. Important: Always remember that each device in your wireless network MUST use the same encryption method and encryption key or your wireless network will not function properly.
39Appendix C: Wireless SecuritySecurity Threats Facing Wireless NetworksWireless-G PCI Adapter with RangeBoosterWPA-Personal. If you do not have a RADIUS server, Select the type of algorithm, TKIP or AES, and enter a password in the Passphrase field of 8-63 characters.WPA2-Personal. Enter a password in the Passphrase field of 8-63 characters.WPA-Enterprise. WPA used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router or other device.) WPA Radius offers two encryption methods, TKIP and AES, with dynamic encryption keys. RADIUS. WEP used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router or other device.) Implementing encryption may have a negative impact on your network’s performance, but if you are transmitting sensitive data over your network, encryption should be used. These security recommendations should help keep your mind at ease while you are enjoying the most flexible and convenient technology Linksys has to offer.
40Appendix D: Windows HelpWireless-G PCI Adapter with RangeBoosterAppendix D: Windows HelpAll wireless products require Microsoft Windows. Windows is the most used operating system in the world and comes with many features that help make networking easier. These features can be accessed through Windows Help and are described in this appendix.TCP/IPBefore a computer can communicate with an access point or wireless router, TCP/IP must be enabled. TCP/IP is a set of instructions, or protocol, all PCs follow to communicate over a network. This is true for wireless networks as well. Your PCs will not be able to utilize wireless networking without having TCP/IP enabled. Windows Help provides complete instructions on enabling TCP/IP.Shared ResourcesIf you wish to share printers, folder, or files over your network, Windows Help provides complete instructions on utilizing shared resources.Network Neighborhood/My Network PlacesOther PCs on your network will appear under Network Neighborhood or My Network Places (depending upon the version of Windows you're running). Windows Help provides complete instructions on adding PCs to your network.
41Appendix E: GlossaryWireless-G PCI Adapter with RangeBoosterAppendix E: Glossary802.11b - A wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz.802.11g - A wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of 2.4GHz, and backward compatibility with 802.11b devices.Access Point - A device that allows wireless-equipped computers and other devices to communicate with a wired network. Also used to expand the range of a wireless network.Adapter - A device that adds network functionality to your PC.Ad-hoc - A group of wireless devices communicating directly with each other (peer-to-peer) without the use of an access point.AES (Advanced Encryption Standard) - A method that uses up to 256-bit key encryption to secure data.Backbone - The part of a network that connects most of the systems and networks together, and handles the most data.Bandwidth - The transmission capacity of a given device or network.Bit - A binary digit.CSMA/CA (Carrier Sense Multiple Access/Collision Avoidance) - A method of data transfer that is used to prevent data collisions.CTS (Clear To Send) - A signal sent by a wireless device, signifying that it is ready to receive data.Default Gateway - A device that forwards Internet traffic from your local area network.DHCP (Dynamic Host Configuration Protocol) - A networking protocol that allows administrators to assign temporary IP addresses to network computers by "leasing" an IP address to a user for a limited amount of time, instead of assigning permanent IP addresses.DNS (Domain Name Server) - The IP address of your ISP's server, which translates the names of websites into IP addresses.Domain - A specific name for a network of computers.
42Appendix E: GlossaryWireless-G PCI Adapter with RangeBoosterDSSS (Direct-Sequence Spread-Spectrum) - Frequency transmission with a redundant bit pattern resulting in a lower probability of information being lost in transit.Encryption - Encoding data transmitted in a network. Ethernet - IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission medium.Fragmentation -Breaking a packet into smaller units when transmitting over a network medium that cannot support the original size of the packet. Gateway - A device that interconnects networks with different, incompatible communications protocols. Hardware - The physical aspect of computers, telecommunications, and other information technology devices.Infrastructure - A wireless network that is bridged to a wired network via an access point.IP (Internet Protocol) - A protocol used to send data over a network.IP Address - The address used to identify a computer or device on a network.ISM band - Radio bandwidth utilized in wireless transmissions.ISP (Internet Service Provider) - A company that provides access to the Internet. LAN - The computers and networking products that make up your local network.MAC (Media Access Control) Address - The unique address that a manufacturer assigns to each networking device. Mbps (MegaBits Per Second) - One million bits per second; a unit of measurement for data transmission.Network - A series of computers or devices connected for the purpose of data sharing, storage, and/or transmission between users.Node - A network junction or connection point, typically a computer or work station.Packet - A unit of data sent over a network.Passphrase - Used much like a password, a passphrase simplifies the WEP encryption process by automatically generating the WEP encryption keys for Linksys products.Port - The connection point on a computer or networking device used for plugging in cables or adapters.
43Appendix E: GlossaryWireless-G PCI Adapter with RangeBoosterRADIUS (Remote Authentication Dial-In User Service) - A protocol that uses an authentication server to control network access.Roaming - The ability to take a wireless device from one access point's range to another without losing the connection.Router - A networking device that connects multiple networks together.RTS (Request To Send) - A networking method of coordinating large packets through the RTS Threshold setting.Server - Any computer whose function in a network is to provide user access to files, printing, communications, and other services. Software - Instructions for the computer. A series of instructions that performs a particular task is called a "program".Spread Spectrum - Wideband radio frequency technique used for more reliable and secure data transmission.SSID (Service Set IDentifier) - Your wireless network's name.Subnet Mask - An address code that determines the size of the network.Switch - 1. A data switch that connects computing devices to host computers, allowing a large number of devices to share a limited number of ports. 2. A device for making, breaking, or changing the connections in an electrical circuit. TCP (Transmission Control Protocol) - A network protocol for transmitting data that requires acknowledgement from the recipient of data sent.TCP/IP (Transmission Control Protocol/Internet Protocol) - A set of instructions PCs use to communicate over a network.TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for each packet transmitted.Topology - The physical layout of a network.WEP (Wired Equivalent Privacy) - A method of encrypting network data transmitted on a wireless network for greater security.WPA (Wi-Fi Protected Access) - a wireless security protocol using TKIP (Temporal Key Integrity Protocol) encryption, which can be used in conjunction with a RADIUS server.
44Appendix F: SpecificationsWireless-G PCI Adapter with RangeBoosterAppendix F: SpecificationsStandards 802.11g, 802.11b, PCI 2.3Channels 802.11b / 802.11g11 Channels (US, Canada)13 Channels (Europe)14 Channels (Japan)LEDs ACTProtocols 802.11b: CCK (11 Mbps), DQPSK (2 Mbps), DBPSK (1 Mbps); 802.11g: OFDMPeak Gain of the Antenna 2dBiTransmitted Power 802.11b: 17 ± 1dBm (Typical)802.11g: 15 ± 1dBm (Typical)Receive Sensitivity 11Mbps @ -88dBm (Typical)54Mbps @ -78dBm (Typical)Security features WEP and WPA EncryptionWEP key bits 64 Bit and 128 BitDimensions 6.02" x 3.70" x 4.76" (153 mm x 94 mm x 121 mm)Unit Weight 2.68 oz. (0.076 kg.)Certifications FCC, Wi-FiOperating Temp. 0° C to 55° C (32° F to 131° F)2.48dBi
45Appendix F: SpecificationsWireless-G PCI Adapter with RangeBoosterStorage Temp. -20° C to 85° C (-4° F to 185° F)Operating Humidity Maximum 90% Non-CondensingStorage Humidity Maximum 90% Non-Condensing
46Appendix G: Warranty InformationWireless-G PCI Adapter with RangeBoosterAppendix G: Warranty InformationLIMITED WARRANTYLinksys warrants to You that, for a period of three years (the “Warranty Period”), your Linksys Product will be substantially free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys' entire liability under this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any rebates. This limited warranty extends only to the original purchaser. If the Product proves defective during the Warranty Period call Linksys Technical Support in order to obtain a Return Authorization Number, if applicable. BE SURE TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN CALLING. If You are requested to return the Product, mark the Return Authorization Number clearly on the outside of the package and include a copy of your original proof of purchase. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. You are responsible for shipping defective Products to Linksys. Linksys pays for UPS Ground shipping from Linksys back to You only. Customers located outside of the United States of America and Canada are responsible for all shipping and handling charges. ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to You. This warranty gives You specific legal rights, and You may also have other rights which vary by jurisdiction.This warranty does not apply if the Product (a) has been altered, except by Linksys, (b) has not been installed, operated, repaired, or maintained in accordance with instructions supplied by Linksys, or (c) has been subjected to abnormal physical or electrical stress, misuse, negligence, or accident. In addition, due to the continual development of new techniques for intruding upon and attacking networks, Linksys does not warrant that the Product will be free of vulnerability to intrusion or attack.TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT (INCLUDING ANY SOFTWARE), EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if any warranty or remedy provided under this Agreement fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You.Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623.
47Appendix H: Regulatory InformationWireless-G PCI Adapter with Range BoosterAppendix H: Regulatory InformationFCC StatementThis product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna• Increase the separation between the equipment or devices• Connect the equipment to an outlet other than the receiver's• Consult a dealer or an experienced radio/TV technician for assistanceFCC Radiation Exposure StatementThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.Safety NoticesCaution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord.Do not use this product near water, for example, in a wet basement or near a swimming pool.Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.Industry Canada (Canada)This device complies with Canadian ICES-003 and RSS210 rules.Cet appareil est conforme aux normes NMB-003 et RSS210 d'Industry Canada.
48Appendix H: Regulatory InformationWireless-G PCI Adapter with Range BoosterUser Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE)This document contains important information for users with regards to the proper disposal and recycling of Linksys products. Consumers are required to comply with this notice for all electronic products bearing the following symbol:
49Appendix H: Regulatory InformationWireless-G PCI Adapter with Range Booster
50Appendix H: Regulatory InformationWireless-G PCI Adapter with Range Booster
51Appendix H: Regulatory InformationWireless-G PCI Adapter with Range Booster
52Appendix H: Regulatory InformationWireless-G PCI Adapter with Range BoosterFor more information, visit www.linksys.com.
53Appendix I: Contact InformationWireless-G PCI Adapter with RangeBoosterAppendix I: Contact InformationNeed to contact Linksys?Visit us online for information on the latest products and updates to your existing products at: http://www.linksys.com or ftp.linksys.comCan't find information about a product you want to buyon the web? Do you want to know more about networkingwith Linksys products? Give our advice line a call at: 800-546-5797 (LINKSYS)Or fax your request in to: 949-823-3002If you experience problems with any Linksys product,you can call us at: 800-326-7114Don't wish to call? You can e-mail us at: support@linksys.comIf any Linksys product proves defective during its warranty period,you can call the Linksys Return Merchandise Authorizationdepartment for obtaining a Return Authorization Number at: 949-823-3000(Details on Warranty and RMA issues can be found in the WarrantyInformation section in this Guide.)
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Linksys declares that WMP54GR (FCC ID: Q87-WMP54GR ) is limited in CH1~CH11 for 2.4 GHz by specified firmware controlled in U.S.A.
IC statement Operation is subject to the following two conditions: 1) This device may not cause interference and 2) This device must accept any interference, including interference that may cause undesired operation of the device. This device has been designed to operate with an antenna having a maximum gain of 2.48 dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. IMPORTANT NOTE: IC Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with IC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Règlement d’Industry Canada Les conditions de fonctionnement sont sujettes à deux conditions: 1) Ce périphérique ne doit pas causer d’interférence et. 2) Ce périphérique doit accepter toute interférence, y compris les interférences pouvant perturber le bon fonctionnement de ce périphérique.

Navigation menu