LINKSYS WAP54GV3 Wireless-G Access Point User Manual UserMan Q87 WAP54GV3

LINKSYS LLC Wireless-G Access Point UserMan Q87 WAP54GV3

Users Manual

A Division of Cisco Systems, Inc.®Model No.Access PointWireless-GWAP54G ver. 3User GuideWIRELESSGHz2.4802.11g
Wireless-G Access PointCopyright and TrademarksSpecifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2005 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.How to Use this User GuideThe user guide to the Wireless-G Access Point has been designed to make understanding networking with the Access Point easier than ever. Look for the following items when reading this User Guide:In addition to these symbols, there are definitions for technical terms that are presented like this:Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like this:Figure numbers and descriptions can also be found in the “List of Figures” section.This exclamation point means there is a caution or warning and is something that could damage your property or the Access Point.word: definition.This checkmark means there is a note of interest and is something you should pay special attention to while using the Access Point.This question mark provides you with a reminder about something you might need to do while using the Access Point.Figure 0-1: Sample Figure DescriptionWAP54G_V3-UG-50509NC JLWARNING: This product contains chemicals, including lead, known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.
Wireless-G Access PointTable of ContentsChapter 1: Introduction 1Welcome 1What’s in this User Guide? 2Chapter 2: Planning Your Wireless Network 4Network Topology 4Roaming 4Network Layout 5Chapter 3: Getting to Know the Wireless-G Access Point 6The Front Panel 6The Back Panel 7Chapter 4: Connecting the Wireless-G Access Point 8Overview 8Connections for Setup 8Chapter 5: Setting up the Wireless-G Access Point 9Overview 9Using the Setup Wizard 9Chapter 6: Using the Linksys Wireless Guard Service 25Client Software Installation 25Network Access 28Your Account 29Chapter 7: Configuring the Wireless-G Access Point 36Overview 36Navigating the Utility 36Accessing the Utility 38The Setup - Network Setup Tab 38The Setup - AP Mode Tab 40The Wireless - Basic Wireless Settings Tab 43The Wireless - Wireless Security Tab 45The Wireless - Wireless MAC Filter Tab 48The Wireless - Advanced Wireless Settings Tab 49The Administration - Management Tab 51The Administration - SNMP Tab 52
Wireless-G Access PointThe Administration - Log Tab 53The Administration - Factory Defaults Tab 54The Administration - Firmware Upgrade Tab 54The Status - Local Network Tab 55The Status - Wireless Network Tab 56Appendix A: Troubleshooting 57Frequently Asked Questions 57Appendix B: Wireless Security 61Security Precautions 61Security Threats Facing Wireless Networks 61Appendix C: Upgrading Firmware 64Appendix D: Windows Help 65Appendix E: Glossary 66Appendix F: Specifications 73Appendix G: Warranty Information 75Appendix H: Regulatory Information 76Appendix I: Contact Information 77
Wireless-G Access PointList of FiguresFigure 3-1: Front Panel 6Figure 3-2: Back Panel 7Figure 4-1: Connect the Ethernet Network Cable 8Figure 4-2: Connect the Power 8Figure 5-1: Welcome Screen 9Figure 5-2: Connect the Network Cable to the Router or Switch Screen 10Figure 5-3: Connect the Network Cable to the Access Point Screen 10Figure 5-4: Power on the Access Point Screen 11Figure 5-5: Check the Access Point’s Status Screen 11Figure 5-6: Select the Access Point Screen 12Figure 5-7: Password Screen 12Figure 5-8: Basic Settings Screen 13Figure 5-9: Configure Wireless Settings Screen 13Figure 5-10: SecureEasySetup Screen 14Figure 5-11: SecureEasySetup Logo 14Figure 5-12: Additional Information - Hardware Button 14Figure 5-13: Additional Information - Software Button 14Figure 5-14: Configure Wireless Settings Screen 15Figure 5-15: Confirm New Settings Screen 15Figure 5-16: Congratulations Screen 16Figure 5-17: Configure Wireless Settings Screen 17Figure 5-18: Wireless Settings Screen 17Figure 5-19: Security Settings Screen 18Figure 5-20: WEP Settings Screen 18Figure 5-21: WPA Personal Settings 19Figure 5-22: WPA2 Personal Settings Screen 19Figure 5-23: WPA2 Mixed Mode Settings Screen 20Figure 5-24: Confirm New Settings Screen 21
Wireless-G Access PointFigure 5-25: Congratulations Screen 21Figure 5-26: Attention Screen 22Figure 5-27: Linksys Wireless Guard Setup Screen 22Figure 5-28: Securing Your Access Point Screen 23Figure 5-29: Wireless Guard Password Screen 23Figure 5-30: Adding Authorized Users Screen 24Figure 5-31: Wireless Guard Congratulations Screen 24Figure 6-1: Note 25Figure 6-2: Configuring Windows Installer 25Figure 6-3: Exit Other Applications 26Figure 6-4: License Agreement 26Figure 6-5: Destination Location 27Figure 6-6: Copying Files 27Figure 6-7: Restart Your Computer 28Figure 6-8: The Network Access Screen 28Figure 6-9: Member Login 29Figure 6-10: Home 30Figure 6-11: Network Administration 30Figure 6-12: Modify Access Control 31Figure 6-13: Add Guest 31Figure 6-14: Add Member 32Figure 6-15: Welcome 32Figure 6-16: Subscriber Information 33Figure 6-17: Account Finances 33Figure 6-18: Credentials Information 34Figure 6-19: Congratulations 34Figure 7-1: Login Screen 38Figure 7-2: Setup - Automatic Configuration - DHCP Screen 38Figure 7-3: Setup - Static IP Screen 39Figure 7-4: Setup - AP Mode Screen 40
Wireless-G Access PointFigure 7-5: Site Survey Screen 40Figure 7-6: Wireless Repeater Diagram 41Figure 7-7: Wireless Bridge Diagram 42Figure 7-8: Wireless - Basic Wireless Settings Screen 43Figure 7-9: Press the SecureEasySetup Button for Your Wireless Client 43Figure 7-10: Waiting for Completion of SecureEasySetup 44Figure 7-11: SecureEasySetup Completed Screen 44Figure 7-12: Confirm Reset 44Figure 7-13: Wireless - Wireless Security (WPA-Personal) Screen 45Figure 7-14: Wireless Security - WPA2-Personal Screen 45Figure 7-15: Wireless Security - WPA2-Mixed Screen 46Figure 7-16: Wireless Security - WPA-Enterprise Screen 46Figure 7-17: Wireless Security - RADIUS Screen 47Figure 7-18: Wireless Security - WEP Screen 47Figure 7-19: Wireless - Wireless MAC Filter Screen 48Figure 7-20: Wireless - Advanced Wireless Settings Screen 49Figure 7-21: Administration - Management Screen 51Figure 7-22: Administration - SNMP Screen 52Figure 7-23: Administration - Log Screen 53Figure 7-24: View Log Screen 53Figure 7-25: Administration - Factory Defaults Screen 54Figure 7-26: Administration - Firmware Upgrade Screen 54Figure 7-27: Status - Local Network Screen 55Figure 7-28: Status - Wireless Network Screen 56Figure C-1: Firmware Upgrade 64
1Chapter 1: IntroductionWelcomeWireless-G Access PointChapter 1: IntroductionWelcomeThank you for choosing the Wireless-G Access Point. This Access Point will allow you to network wirelessly better than ever.How does the Access Point do all of this? An access point allows for greater range and mobility within your wireless network while also allowing you to connect the wireless network to a wired environment.But what does all of this mean? Networks are useful tools for sharing computer resources. You can access one printer from different computers and access data located on another computer's hard drive. Networks are even used for playing multiplayer video games. So, networks are not only useful in homes and offices, they can also be fun.PCs on a wired network create a LAN, or Local Area Network. They are connected with Ethernet cables, which is why the network is called "wired". PCs equipped with wireless cards and adapters can communicate without cumbersome cables. By sharing the same wireless settings, within their transmission radius, they form a wireless network. This is sometimes called a WLAN, or Wired Local Area Network. The Access Point bridges wireless networks of both 802.11g and 802.11b standards and wired networks.Use the instructions in this Guide to help you connect the Access Point, set it up, and configure it to bridge your different networks. These instructions should be all you need to get the most out of the Access Point.802.11b: a wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz.802.11g: a wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of 2.4GHz, and backward compatibility with 802.11b devices.adapter: a device that adds network functionality to your PC.ethernet: network protocol that specifies how data is placed on and retrieved from a common transmission medium.lan (local area network): the computers and networking products that make up your local network.network: a series of computers or devices connected together. access point: a device that allows wireless-equipped computers and other devices to communicate with a wired network. Also used to expand the range of a wireless network.
2Chapter 1: IntroductionWhat’s in this User Guide?Wireless-G Access PointWhat’s in this User Guide?This user guide covers the steps for setting up and using the Wireless-G Access Point.• Chapter 1: IntroductionThis chapter describes the Access Point’s applications and this User Guide.• Chapter 2: Planning your Wireless NetworkThis chapter describes the basics of wireless networking.• Chapter 3: Getting to Know the Wireless-G Access PointThis chapter describes the physical features of the Access Point.• Chapter 4: Connecting the Wireless-G Access PointThis chapter instructs you on how to connect the Access Point to your network.• Chapter 5: Setting Up the Wireless-G Access PointThis chapter explains how to use the Setup Wizard to configure the settings on the Access Point.• Chapter 6: Using the Linksys Wireless Guard ServiceThis chapter explains how to use the Linksys Wireless Guard service to secure your network.• Chapter 7: Configuring the Wireless-G Access PointThis chapter explains how to use the Access Point’s Web-based Utility for advanced configuration.• Appendix A: TroubleshootingThis appendix describes some frequently asked questions regarding installation and use of the Access Point.• Appendix B: Wireless SecurityThis appendix explains the risks of wireless networking and some solutions to reduce the risks.• Appendix C: Upgrading FirmwareThis appendix instructs you on how to upgrade the Access Point’s firmware.• Appendix D: Windows HelpThis appendix describes some of the ways Windows can help you with wireless networking.• Appendix E: GlossaryThis appendix gives a brief glossary of terms frequently used in networking.• Appendix F: SpecificationsThis appendix provides the Access Point’s technical specifications.
3Chapter 1: IntroductionWhat’s in this User Guide?Wireless-G Access Point• Appendix G: Warranty InformationThis appendix supplies the Access Point’s warranty information.• Appendix H: Regulatory InformationThis appendix supplies the Access Point’s regulatory information.• Appendix I: Contact InformationThis appendix provides contact information for a variety of Linksys resources, including Technical Support.
4Chapter 2: Planning Your Wireless NetworkNetwork TopologyWireless-G Access PointChapter 2: Planning Your Wireless NetworkNetwork TopologyA wireless network is a group of computers, each equipped with one wireless adapter. Computers in a wireless network must be configured to share the same radio channel. Several PCs equipped with wireless cards or adapters can communicate with one another to form an ad-hoc network.Linksys wireless adapters also provide users access to a wired network when using an access point, such as the Wireless-G Access Point, or wireless router. An integrated wireless and wired network is called an infrastructure network. Each wireless PC in an infrastructure network can talk to any computer in a wired network infrastructure via the access point or wireless router.An infrastructure configuration extends the accessibility of a wireless PC to a wired network, and may double the effective wireless transmission range for two wireless adapter PCs. Since an access point is able to forward data within a network, the effective transmission range in an infrastructure network may be doubled.RoamingInfrastructure mode also supports roaming capabilities for mobile users. Roaming means that you can move your wireless PC within your network and the access points will pick up the wireless PC's signal, providing that they both share the same channel and SSID.Before using the roaming capabilities, choose a feasible radio channel and optimum access point position. Proper access point positioning combined with a clear radio signal will greatly enhance performance.infrastructure: a wireless network that is bridged to a wired network via an access point.ad-hoc: a group of wireless devices communicating directly with each other (peer-to-peer) without the use of an access point.roaming: the ability to take a wireless device from one access point's range to another without losing the connection.ssid: your wireless network's name
5Chapter 2: Planning Your Wireless NetworkNetwork LayoutWireless-G Access PointNetwork LayoutThe Wireless-G Access Point has been designed for use with 802.11g and 802.11b products. The Access Point is compatible with 802.11g and 802.11b adapters, such as the Notebook Adapters for your laptop computers, PCI Adapters for your desktop PCs, and USB Adapters for when you want to enjoy USB connectivity. These wireless products can also communicate with a 802.11g or 802.11b Wireless PrintServer.To link your wired network with your wireless network, connect the Access Point’s Ethernet network port to any switch or router. With these, and many other, Linksys products, your networking options are limitless. Go to the Linksys website at www.linksys.com for more information about wireless products.
6Chapter 3: Getting to Know the Wireless-G Access PointThe Front PanelWireless-G Access PointChapter 3: Getting to Know the Wireless-G Access PointThe Front PanelThe Access Point's LEDs, which indicate activity and status information, are located on the front panel.(Cisco logo) Orange/White. The Cisco logo is the Access Point’s SecureEasySetup button. It lights up when the Access Point is powered on. The Cisco logo is orange when the SecureEasySetup feature is not used, while the color white indicates that the SecureEasySetup feature is being used. When the Access Point enters SecureEasySetup mode, the Cisco logo will turn white and start flashing. Then the Access Point will generate its SSID (network name) and WPA-Personal (also called WPA-PSK) key. If the Access Point successfully associates with a client using SecureEasySetup, the Cisco logo will stop flashing and stay white. If the association is unsuccessful, then the Cisco logo will stop flashing and stay orange.To clear the SSID and WPA-Personal key, press and hold down the Cisco logo for ten seconds. The Cisco logo will turn orange to indicate a successful reset.Power Red. The Power LED lights up when the Access Point is powered on.Act Green. The Act LED lights up when the Access Point is ready for wireless use. It flashes when the Access Point is transmitting or receiving data wirelessly.Link Orange. The Link LED lights up when the Access Point is successfully connected to a device through the Ethernet network port. The LED flashes when the Access Point is transmitting or receiving data through the Ethernet network port.Figure 3-1: Front PanelNOTE: SecureEasySetup is a feature that makes it easy to set up your wireless network. If you have SecureEasySetup devices, run the Setup Wizard on the Access Point’s Setup Wizard CD-ROM. Then follow the on-screen instructions.
7Chapter 3: Getting to Know the Wireless-G Access PointThe Back PanelWireless-G Access PointThe Back PanelThe Access Point's Ethernet network and power ports, as well as the Reset button, are located on the back panel.LAN Port The Ethernet network port connects to an Ethernet network device, such as a switch or router.Reset Button There are two ways to reset the Access Point's factory defaults. Either press the Reset button,for approximately ten seconds, or use the Administration - Factory Defaults screen of the Access Point's Web-based Utility.Power Port The Power port connects to the Access Point’s power adapter.Figure 3-2: Back Panelport: the connection point on a computer or networking device used for plugging in cables or adaptersIMPORTANT: Resetting the Access Point will erase all of your settings (including wireless security, IP address, and power output) and replace them with the factory defaults. Do not reset the Access Point if you want to retain these settings.
8Chapter 4: Connecting the Wireless-G Access PointOverviewWireless-G Access PointChapter 4: Connecting the Wireless-G Access PointOverviewThis chapter explains how to connect the Access Point for setup.Connections for Setup1. Connect your Ethernet network cable to your network router or switch. Then connect the other end of the network cable to the Access Point’s LAN (Ethernet network) port.2. Connect the included power adapter to the Access Point’s Power port. Then plug the power adapter into an electrical outlet. The LEDs on the front panel will light up as soon as the Access Point’s powers on.Proceed to “Chapter 5: Setting Up the Wireless-G Access Point.”Figure 4-1: Connect the Ethernet Network CableFigure 4-2: Connect the Power
9Chapter 5: Setting up the Wireless-G Access PointOverviewWireless-G Access PointChapter 5: Setting up the Wireless-G Access PointOverviewNow that you've connected the Access Point to your wired network, you are ready to begin setting it up. This Setup Wizard will take you through all the steps necessary to configure the Access Point.Using the Setup Wizard1. Insert the Setup Wizard CD-ROM into your CD-ROM drive. The Setup Wizard should run automatically, and the Welcome screen should appear. If it does not, click the Start button and choose Run. In the field that appears, enter D:\setup.exe (if “D” is the letter of your CD-ROM drive).2. On the Welcome screen, click the Click Here to Start or Setup button if this is the first time you are running the Setup Wizard. These are your other choices:Install Linksys Wireless Guard - Linksys Wireless Guard is a subscription service available to secure your network. To install the client software needed to use this service, click the Install Linksys Wireless Guardbutton, and proceed to “Chapter 6: Using the Linksys Wireless Guard Service.” User Guide - Click the User Guide button to open the PDF file of this User Guide.Exit - Click the Exit button to exit the Setup Wizard.Figure 5-1: Welcome ScreenNOTE: Before installing the client software on your computer, you should set up the Access Point and sign up for the Linksys Wireless Guard service.
10Chapter 5: Setting up the Wireless-G Access PointUsing the Setup WizardWireless-G Access Point3. Optimally, you should set up the Access Point using a PC on your wired network. Connect a network cable to your network router or switch. Then click the Next button.4. The screen shows how the Access Point should be connected as you run the Setup Wizard. Connect the other end of the network cable to the Access Point’s Ethernet network port. Then click the Next button.Figure 5-2: Connect the Network Cable to the Router or Switch ScreenFigure 5-3: Connect the Network Cable to the Access Point Screen
11Chapter 5: Setting up the Wireless-G Access PointUsing the Setup WizardWireless-G Access Point5. Connect the power adapter to the Access Point and an electrical outlet. Then click the Next button.6. Make sure the Access Point’s Power, Act, and Link LEDs are lit on its front panel. If they are not, check your cable connections. Then click the Next button to continue.Figure 5-4: Power on the Access Point ScreenFigure 5-5: Check the Access Point’s Status Screen
12Chapter 5: Setting up the Wireless-G Access PointUsing the Setup WizardWireless-G Access Point7. The Setup Wizard will run a search for the Access Point within your network and then display a list along with the status information for the selected access point. If this is the only access point on your network, it will be the only one displayed. If there are more than one displayed, select the Access Point by clicking on it. Click the Yes button to change any settings, or click the No button to keep these settings.8. You will be asked to sign onto the Access Point you have selected. Enter the default password, admin. Then, click Enter. (This user name and password can be changed from the Web-based Utility's Administration - Management tab.)Figure 5-6: Select the Access Point ScreenFigure 5-7: Password Screen
13Chapter 5: Setting up the Wireless-G Access PointUsing the Setup WizardWireless-G Access Point9. The Basic Settings screen will appear next. Enter a descriptive name in the Device Name field. Create a password that will control access to the Access Point’s Web-based Utility and Setup Wizard.If your network router will automatically assign an IP address to the Access Point, then select Automatic-DHCP.If you want to assign a static or fixed IP address to the Access Point, then select Static IP. Enter the IP Address, Subnet Mask, and Default Gateway settings. If you are not sure what changes you should make, then keep the default values.Then, click the Next button to continue or Back to return to the previous page.Device Name - Enter a descriptive name for the Access Point.Password - Enter a password that will control access to the Utility and Setup Wizard.IP Address - This IP address must be unique to your network. (The default IP address is 192.168.1.245.)Subnet Mask - The Access Point's Subnet Mask must be the same as the subnet mask of your Ethernet network.Default Gateway - Enter the IP address of your network gateway (usually your router).Click the Next button to continue or the Back button to return to the previous screen.10. There are two ways to configure the Access Point’s wireless settings, SecureEasySetup and manual configuration.If you have other SecureEasySetup devices, such as notebook adapters or printers, then you can use the Access Point’s SecureEasySetup feature to configure your wireless network. Proceed to the section, “Using the Access Point’s SecureEasySetup Feature.”If you do not have other SecureEasySetup devices, then proceed to the section, “Manually Configuring the Access Point’s Wireless Settings.”Figure 5-8: Basic Settings ScreenFigure 5-9: Configure Wireless Settings ScreenNOTE: If you have already set up your network using your router’s SecureEasySetup feature, then you cannot use the Access Point’s SecureEasySetup feature. You must manually configure the Access Point’s wireless settings to match your existing network’s settings.
14Chapter 5: Setting up the Wireless-G Access PointUsing the Setup WizardWireless-G Access PointUsing the Access Point’s SecureEasySetup FeatureRead these instructions before you press any SecureEasySetup buttons. You should locate the SecureEasySetup buttons of your devices before using the Access Point’s SecureEasySetup feature.1. Before you push any button, locate the SecureEasySetup button for each of your other SecureEasySetup devices. If you are not sure where to find this button, click Where is my other SecureEasySetup button?You will see a screen showing the SecureEasySetup logo. Click the Next button to continue or the Closebutton to return to the Configure Wireless Settings screen.You will see a screen with instructions on how to locate the SecureEasySetup hardware button. If your device does not have a hardware button, it most likely will have a software button. Click the Next button for instructions to locate the software button, or click the Close button to return to the Configure Wireless Settings screen.You will see a screen with instructions on how to locate the SecureEasySetup software button. Click the Close button to return to the Configure Wireless Settings screen.Figure 5-10: SecureEasySetup ScreenFigure 5-11: SecureEasySetup LogoNOTE: SecureEasySetup uses WPA-Personal encryption. If your current wireless devices do not support WPA-Personal security, then you cannot use SecureEasySetup on your network. You will need to manually configure your network security using the encryption supported by your existing devices.Figure 5-12: Additional Information - Hardware ButtonFigure 5-13: Additional Information - Software Button
15Chapter 5: Setting up the Wireless-G Access PointUsing the Setup WizardWireless-G Access Point2. Press the Access Point’s orange Cisco logo on its front panel. When the logo turns white and begins to flash, press the SecureEasySetup button on another device. The Access Point’s Cisco logo will stop flashing when the device has been added to the network. Then repeat this procedure for each additional SecureEasySetup device.When you have finished configuring the devices in your wireless network, click the Next button to continue.3. The Setup Wizard will ask you to review your settings before it saves them. Click the Yes button if you are satisfied with your settings, or click the No button if you do not want to save your new settings.Figure 5-14: Configure Wireless Settings ScreenFigure 5-15: Confirm New Settings ScreenNOTE: You can only add one SecureEasySetup device at a time.NOTE: Write down these settings. You may need to manually configure non-SecureEasySetup devices in the future.
16Chapter 5: Setting up the Wireless-G Access PointUsing the Setup WizardWireless-G Access Point4. The Congratulations screen will appear. Click the Online Registration button to register the Access Point, or click the Exit button to exit the Setup Wizard.Congratulations! The installation of the Wireless-G Access Point is complete.If you need to configure a non-SecureEasySetup device, proceed to the next section, “Configuring a Non-SecureEasySetup Device.”If you want to make advanced configuration changes, proceed to “Chapter 7: Configuring the Wireless-G Access Point.”Configuring a Non-SecureEasySetup DeviceIf you need to configure a non-SecureEasySetup device, then proceed with the setup of your non-SecureEasySetup device. When you have to configure its wireless settings, enter the settings you wrote down when you saw the Confirm New Settings screen at the end of the Setup Wizard.If you did not write down these settings, then you will use the Access Point’s Web-based Utility. Follow these instructions:1. Launch Internet Explorer or Netscape Navigator. In the Address field, enter the Access Point’s default IP address, 192.168.1.245, or the IP address you entered during the Setup Wizard. (Should you need to learn what IP address the Access Point presently uses, run the Setup Wizard again. It will scan the Access Point and give you its IP address.) Press the Enter key.2. The login screen will appear. Enter admin in the User Name field. The first time you open the Web-based Utility, use the default password, admin. (You can set a new password from the Administration - Management tab.) Then click the OK button.3. Click the Wireless tab. The Access Point’s Network Name (SSID) will appear on the Basic Wireless Settings screen. Write down the Network Name (SSID) for the Access Point.4. Click the Wireless Security tab. The Access Point’s WPA-Personal settings will appear on the Wireless Security screen. Write down the Passphrase for the Access Point.5. When you configure the wireless settings for your non-SecureEasySetup devices, enter the Access Point’s Network Name (SSID) and Passphrase when you are asked for them.If you want additional information about the Web-based Utility, proceed to “Chapter 7: Configuring the Wireless-G Access Point.”Figure 5-16: Congratulations ScreenNOTE: Some devices may call the Passphrase a Pre-Shared Key instead. They are different names for the same key.
17Chapter 5: Setting up the Wireless-G Access PointUsing the Setup WizardWireless-G Access PointManually Configuring the Access Point’s Wireless Settings1. If you do not have other SecureEasySetup devices, then click the Enter Wireless Settings Manually button.2. The Setup Wizard will ask you to enter the SSID, Channel, and Network Mode settings for your wireless network.SSID - Enter the name of your wireless network. The SSID must be identical for all devices in the network. The default setting is linksys (all lowercase).Channel - Select the operating channel for your wireless network. All of your wireless devices will use this channel to communicate.Network Mode - Select the wireless standards running on your network. If you have both 802.11g and 802.11b devices in your network, keep the default setting, Mixed Mode. If you have only 802.11g devices, select G-Only. If you have only 802.11b devices, select B-Only. If you want to disable your wireless network, select Disable.Click the Next button to continue or the Back button to return to the previous screen.Figure 5-17: Configure Wireless Settings ScreenFigure 5-18: Wireless Settings Screen
18Chapter 5: Setting up the Wireless-G Access PointUsing the Setup WizardWireless-G Access Point3. Select the level of security you want to use: WEP,WPA/WPA2 Personal,WPA-Enterprise, or Linksys Wireless Guard. WEP stands for Wired Equivalent Privacy, and WPA stands for Wi-Fi Protected Access. Click the Next button and proceed to step 4.If you want to use WPA-Enterprise, then you should select Disabled and use the Access Point’s Web-based Utility to configure your wireless security settings. (Refer to “Chapter 7: Configuring the Wireless-G Access Point.”) Click the Next button and proceed to step 5.If you do not want to use any wireless security method, select Disabled and then click the Next button. Proceed to step 5.4. Proceed to the appropriate section for your security method.WEP (64-Bit)To use 64-bit WEP encryption, select WEP (64-bit). Then enter a passphrase or WEP key.Passphrase - Enter a passphrase in the Passphrase field, so a WEP key is automatically generated. The passphrase is case-sensitive and should not be longer than 16 alphanumeric characters. It must match the passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If you have any non-Linksys wireless products, enter the WEP key manually on those products.)WEP Key - The WEP key you enter must match the WEP key of your wireless network. For 64-bit encryption, enter exactly 10 hexadecimal characters. Valid hexadecimal characters are “0” to “9” and “A” to “F”.Click the Next button to continue or the Back button to return to the previous screen.WEP (128-Bit)To use 128-bit WEP encryption, select WEP (128-bit). Then enter a passphrase or WEP key.Passphrase - Enter a passphrase in the Passphrase field, so a WEP key is automatically generated. The passphrase is case-sensitive and should not be longer than 16 alphanumeric characters. It must match the passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If you have any non-Linksys wireless products, enter the WEP key manually on those products.)WEP Key - The WEP key you enter must match the WEP key of your wireless network. For 128-bit encryption, enter exactly 26 hexadecimal characters. Valid hexadecimal characters are “0” to “9” and “A” to “F”.Click the Next button to continue or the Back button to return to the previous screen.Figure 5-20: WEP Settings ScreenFigure 5-19: Security Settings Screenwep (wired equivalent privacy): a method of encrypting network data transmitted on a wireless network for greater security.encryption: encoding data transmitted in a network.
19Chapter 5: Setting up the Wireless-G Access PointUsing the Setup WizardWireless-G Access PointWPA PersonalTo use WPA Personal security, select WPA Personal from the Security drop-down menu. WPA Personal offers two encryption methods, TKIP and AES, with dynamic encryption keys. Select TKIP or AES for encryption. Then enter a Passphrase that is 8-32 characters in length.Encryption - Select TKIP or AES from the Encryption drop-down menu.Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-32 characters in the Passphrase field.The longer and more complex your Passphrase is, the more secure your network will be.Click the Next button to continue or the Back button to return to the previous screen.WPA2 PersonalTo use WPA2 Personal security, select WPA2 Personal from the Security drop-down menu. WPA2 Personal uses AES encryption with dynamic keys. Enter a Passphrase that is 8-32 characters in length.Encryption - The default for WPA2 Personal, AES, is automatically selected.Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-32 characters in the Passphrase field.The longer and more complex your Passphrase is, the more secure your network will be.Click the Next button to continue or the Back button to return to the previous screen.Figure 5-21: WPA Personal SettingsFigure 5-22: WPA2 Personal Settings Screenwpa (wi-fi protected access: a wireless security protocol using TKIP (Temporal Key Integrity Protocol) encryption, which can be used in conjunction with a RADIUS server.
20Chapter 5: Setting up the Wireless-G Access PointUsing the Setup WizardWireless-G Access PointWPA2 Mixed ModeTo use WPA2 Mixed Mode security, select WPA2 Mixed Mode from the Security drop-down menu. WPA2 Mixed Mode uses TKIP and AES for encryption. Enter a Passphrase that is 8-32 characters in length.Encryption - The default for WPA2 Personal, TKIP +AES, is automatically selected.Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-32 characters in the Passphrase field.The longer and more complex your Passphrase is, the more secure your network will be.Click the Next button to continue or the Back button to return to the previous screen.WPA EnterpriseIf you want to use WPA-Enterprise, then you should select Disabled and use the Access Point’s Web-based Utility to configure your wireless security settings. (Refer to “Chapter 7: Configuring the Wireless-G Access Point.”) Click the Next button and proceed to step 5.Linksys Wireless GuardThis subscription service gives you WPA Enterprise security without the work of building your own RADIUS server. Click Learn more to visit www.linksys.com/wirelessguard.If you want to use the Linksys Wireless Guard service, select Linksys Wireless Guard. Click the Next button and proceed to the next section, “Configuring the Linksys Wireless Guard Settings.”Figure 5-23: WPA2 Mixed Mode Settings Screenradius (remote authentication dial-in user service): a protocol that uses an authentication server to control network access.
21Chapter 5: Setting up the Wireless-G Access PointUsing the Setup WizardWireless-G Access Point5. The Setup Wizard will ask you to review your settings before it saves them. Click the Yes button if you are satisfied with your settings, or click the No button if you do not want to save your new settings.6. The Congratulations screen will appear. Click the Online Registration button to register the Access Point, or click the Exit button to exit the Setup Wizard.Congratulations! The installation of the Wireless-G Access Point is complete.If you want to make advanced configuration changes, proceed to “Chapter 7: Configuring the Wireless-G Access Point.”Figure 5-24: Confirm New Settings ScreenFigure 5-25: Congratulations Screen
22Chapter 5: Setting up the Wireless-G Access PointUsing the Setup WizardWireless-G Access PointConfiguring the Linksys Wireless Guard SettingsLinksys Wireless Guard is a subscription service that gives you WPA Enterprise security without having to build your own RADIUS network. Follow the instructions below. To learn more about Linksys Wireless Guard, go to www.linksys.com/wirelessguard. If you need help with setting up Linksys Wireless Guard, send an e-mail to wirelessguard@linksys.com or call 888-231-5506.1. After selecting Linksys Wireless Guard for your security selection, this screen will appear. Before you continue with the setup, make sure your computer meets the following requirements:• Windows XP or Windows 2000 operating system• 128MB RAM• 50MB free disk space• A wireless network interface with a driver that supports WPA security• Connection to the Internet through a broadband connection (DSL, cable, or other)If you meet these requirements, click Continue to sign up for the Linksys Wireless Guard service, or click Cancel to cancel the setup.2. This screen guides you through the registration process. Enter your user name, password, first and last name, e-mail address, and a security question and answer. Then, click Next to continue or Exit if you want to quit the Setup Wizard.User Name and Password. Enter the user name you want to use in the User Name field. Then enter the Password you want to use in the Password field. Confirm Password. Enter the password again in the Confirm Password field. First and Last Name. Enter your first and last names. E-mail address. Enter your e-mail address in the field provided.Security Question and Answer. Select a security question from the Security Question drop-down menu to help identify you if you forget your password. Enter the answer to your selected question in the Security Answer field.Figure 5-26: Attention ScreenFigure 5-27: Linksys Wireless Guard Setup Screen
23Chapter 5: Setting up the Wireless-G Access PointUsing the Setup WizardWireless-G Access Point3. On the next screen, the Access Point will be automatically selected. Make sure that the correct Access Point is selected and that the name and SSID are correct. If you want to configure a different Access Point, then select it from the list of wireless networks displayed on-screen. Click Next to add this Access Point to your Wireless Guard network or click Back to return to the previous screen.4. For security reasons, the Access Point’s administrator password has been automatically changed. Please note the new password before continuing or you won’t be able to access the Access Point later. After writing down the new password, select I have noted the new password, and then click OK.Figure 5-28: Securing Your Access Point ScreenFigure 5-29: Wireless Guard Password Screen
24Chapter 5: Setting up the Wireless-G Access PointUsing the Setup WizardWireless-G Access Point5. When the next screen appears, you will specify which users you will allow access to this protected network. Enter the E-mail Address, User Name, and Password (once in the Password field and again in the Confirm Password field) for each user. Then, click Add.To remove a user from the list, select the user, and then click Remove.6. The Access Point is now configured for Linksys Wireless Guard. To finish configuring your wireless network, you will need to install the Linksys Wireless Guard client software for each PC that will have access. Click Main Menu, and then click Linksys Wireless Guard Client. (Refer to “Chapter 6: Using the Linksys Wireless Guard Service” for additional information.)To add more Access Points to your Linksys Wireless Guard network, run the Linksys Wireless Guard setup again for each Access Point.Figure 5-30: Adding Authorized Users ScreenFigure 5-31: Wireless Guard Congratulations Screen
25Chapter 6: Using the Linksys Wireless Guard ServiceClient Software InstallationWireless-G Access PointChapter 6: Using the Linksys Wireless Guard ServiceThis chapter is only for users who have signed up for Linksys Wireless Guard to secure their network and have configured the Access Point for Linksys Wireless Guard. (Refer to “Chapter 5: Setting up the Wireless-G Access Point.”)You will now install the client software needed to securely connect a PC to the Access Point that is protected by Linksys Wireless Guard. This chapter will also show you how to access your protected network and manage your account.Client Software Installation1. If you haven’t already done so, on the Welcome screen of the Setup Wizard on the CD-ROM, click LinksysWireless Guard Client. The screen in Figure 6-1 will appear. To install the software on this PC, click Continue. Click Cancel to cancel the installation.2. A screen will appear to notify you that the setup is in process. Wait until the next screen appears. If you want to end the installation process, click Cancel.Figure 6-1: NoteNOTE: Make sure that you have signed up for Linksys Wireless Guard and that you have configured the Access Point for Linksys Wireless Guard before installing the client software.Figure 6-2: Configuring Windows Installer
26Chapter 6: Using the Linksys Wireless Guard ServiceClient Software InstallationWireless-G Access Point3. The next screen will tell you to close all other applications before continuing. If no other applications are open, click Next to continue. If you want to exit to close your other applications, click Cancel.4. A license agreement will appear next. Scroll down or press PAGE DOWN to read the entire agreement. To accept the terms and continue the installation, click Yes. To quit the installation, click No.Figure 6-3: Exit Other ApplicationsFigure 6-4: License Agreement
27Chapter 6: Using the Linksys Wireless Guard ServiceClient Software InstallationWireless-G Access Point5. On this screen, you will be informed where the Linksys Wireless Guard client software will be installed. To install to this folder, click Next. If you want to choose a different location for the folder, click the Browse button and select the location.Click Back to return to the previous screen. Click Cancel to cancel the installation.6. The InstallShield Wizard will start copying program files. Click Next to continue.Click Back to return to the previous screen. Click Cancel to cancel the installation.Figure 6-5: Destination LocationFigure 6-6: Copying Files
28Chapter 6: Using the Linksys Wireless Guard ServiceNetwork AccessWireless-G Access Point7. The Linksys Wireless Guard client software is successfully installed. Before you can use the program, you must restart your computer. Select Yes to restart your computer now. Select No to restart your computer at a later time. Remove any disks that are in their drives, and then click Finish.8. After the Linksys Wireless Guard client software is installed, a key icon will be displayed on the right side of the system tray at the bottom of your screen. The color of the key will change according to the status of the network connection. The most common colors are described below.Green - Connected.Green with Red X - Connected, but waiting for authentication.Gray - Not connected.Red - Connected to a network that is not protected by Linksys Wireless Guard.Network AccessAfter Linksys Wireless Guard is installed, any time you access a Linksys Wireless Guard protected network, this screen will appear. To access your network, click Login as a Wireless Guard Member, or if you are a guest, click Login as a Wireless Guard Guest. Enter your user name and password, and then click Login.Login as a Wireless Guard Member. Select this option if you are a registered member.Login as a Wireless Guard Guest. Select this option if you are a registered guest member. The guest must first be added as a guest at the Membership and Network Administration Website. See the “Add a Guest” section, shown below.Save Password. Select this if you want the system to remember your password so you don’t have to enter it when you log in.Enable Auto Login. Select this if you want the system to bypass the login.Click Cancel to cancel the login, or if you forget your password, click Lost Password.Figure 6-7: Restart Your ComputerFigure 6-8: The Network Access Screen
29Chapter 6: Using the Linksys Wireless Guard ServiceYour AccountWireless-G Access PointYour AccountThis section explains how to access your account, how to add a guest, how to add another member to your account, and how to secure and unprotect the Linksys Wireless Guard network.For more detailed information on your account and the website, click your computer’s Start button, select theLinksys Wireless Guard folder, and then click Linksys Wireless Guard Help. For further information on Linksys Wireless Guard only, you can contact Linksys Wireless Guard Technical Support at 888 231-5506 or send an e-mail to wirelessguard@linksys.com.Accessing your AccountRight-click on the green Wireless Guard Network key icon, and then click View Membership and Network Administration Website to log in to the Linksys Wireless Guard website. You can also click on your computer’s Start button, select the Linksys Wireless Guard folder, then click Membership and Network Administration Website.1. The screen in Figure 6-9 will appear. Enter the administrator’s user name and password in the fields provided. Click Login.2. The Wireless Guard Member Website home screen will appear. Through this website, you can modify your member or billing profile, view information about your account or subscription, add or remove members, modify access privileges of members and guests, change network settings, and download updates and documentation. There is a Help tab with extensive information to help you with everything on the website. The instructions for adding a guest or member, as well as securing and unprotecting your network, are also explained below.Figure 6-9: Member Login
30Chapter 6: Using the Linksys Wireless Guard ServiceYour AccountWireless-G Access PointAdd a Guest1. On the Wireless Guard Member Website home screen, click the Network Admin tab.2. The screen in Figure 6-11 will appear. Under Network Administration, click Modify Access Control.Figure 6-10: HomeFigure 6-11: Network Administration
31Chapter 6: Using the Linksys Wireless Guard ServiceYour AccountWireless-G Access Point3. The screen in Figure 6-12 will appear. Under Guests, click Add Guest.4. The screen in Figure 6-13 will appear. Enter the Guest User Name, Guest First Name, Guest Last Name, Password, Password Verify, and Access Duration. Then click Submit.Guest User Name. Enter a user name of the guest you want to add.Guest First Name. Enter the first name of the guest you want to add.Guest Last Name. Enter the last name of the guest you want to add.Password. Enter a password that’s at least six characters long for the guest you want to add.Password Verify. Enter the password again.Access Duration. Enter the length of time (in hours) that the guest will be on the network.5. The guest will need to install the Linksys Wireless Guard Client software on his or her PC. The software can be downloaded from the Setup CD-ROM or from linksys.com/support. Refer to the “Client Software Installation” section at the beginning of this chapter. Figure 6-12: Modify Access ControlFigure 6-13: Add Guest
32Chapter 6: Using the Linksys Wireless Guard ServiceYour AccountWireless-G Access PointAdd a MemberTo add a member, follow the instructions in the “Add a Guest” section, steps 1 through 3, except in step 3, click Add Member.The screen in Figure 6-14 will appear. Registered members can enter their e-mail address in the field provided and select the duration for access from the drop-down menu. If you want this network member to have the authority to put the network in Fallback Mode in case network security is lost, select Permission to Initiate Network Fallback. When finished, click Submit.To register as a member for Linksys Wireless Guard, refer to the following instructions, and then when you are finished with the registration process, return to this screen.The member will need to install the Linksys Wireless Guard Client software on his or her PC. The software can be downloaded from the Setup CD-ROM or from linksys.com/support. Refer to the “Client Software Installation” section at the beginning of this chapter.Member Registration1. Right-click on the green Wireless Guard Network key icon, and then click Register Member.2. The Welcome screen will appear. Click Next.Figure 6-14: Add MemberFigure 6-15: Welcome
33Chapter 6: Using the Linksys Wireless Guard ServiceYour AccountWireless-G Access Point3. When the Enter subscriber information screen appears, enter the first and last names, phone number, if desired, and then e-mail address of the new member. Click Next.Click Back to return to the previous screen. Click Cancel to cancel the member registration.4. When the next screen appears, choose who will be paying for the account. If the new member will be paying for the account, click I will pay for my own subscription. I will enter my billing information on the web site later. If the administrator will be paying for the account, click Another member will be paying for my subscription. Click Next.Click Back to return to the previous screen. Click Cancel to cancel the member registration.Figure 6-17: Account FinancesFigure 6-16: Subscriber Information
34Chapter 6: Using the Linksys Wireless Guard ServiceYour AccountWireless-G Access Point5. When this screen appears, enter the information you will be using with the account. Enter a user name and password, and then enter the password again. Also select a security question and answer in case you forget your password in the future. Click Next to continue.Click Back to return to the previous screen. Click Cancel to cancel the member registration.6. When the Congratulations screen appears, you will be successfully registered for Linksys Wireless Guard. Click Finish.7. You should now ask the administrator to add you to his or her Wireless Guard Protected Network’s Access Control List. To do so, the network administrator needs to return to the Add Member screen in Figure 6-14, above.Figure 6-18: Credentials InformationFigure 6-19: Congratulations
35Chapter 6: Using the Linksys Wireless Guard ServiceYour AccountWireless-G Access PointSecuring or Unprotecting Your Wireless Guard NetworkThere may be some instances when you would want to completely unprotect your network connection so it is not using the Wireless Guard security. For example, if you take your laptop to another location to give a presentation, and connect to a network that is running 802.1x security, the Linksys Wireless Guard software on your laptop will block you from logging in to another network. You will need to manually unprotect your network connection so you can log in. When you come back to your own network, you won't have to manually re-secure the network connection. Linksys Wireless Guard will recognize it and automatically reinstate security. To unprotect a networkRight-click the green Wireless Guard Network key icon on the right-side of the system tray at the bottom of your screen. Select Unprotect this Network Connection from the menu.When the screen asks if you're sure you want to unprotect the network, click Yes.To secure an unprotected networkRight-click the green Wireless Guard Network key icon. Select Secure this Network Connection from the menu.When the screen asks if you're sure you want to secure the network, click Yes.For more detailed information on your account and the website, click your computer’s Start button, select the Linksys Wireless Guard folder, and then click Linksys Wireless Guard Help.
36Chapter 7: Configuring the Wireless-G Access PointOverviewWireless-G Access PointChapter 7: Configuring the Wireless-G Access PointOverviewThe Access Point has been designed to be functional right out of the box, with the default settings in the Setup Wizard. However, if you'd like to change these settings, the Access Point can be configured through your web browser with the Web-based Utility. This chapter explains how to use the Utility.The Utility can be accessed via Microsoft Internet Explorer or Netscape Navigator through use of a computer that is networked with the Access Point.For a basic network setup, most users only have to use the following screens of the Utility:• SetupOn the Network Setup screen, enter your basic network settings here.• ManagementClick the Administration tab and then select the Management screen. The Access Point’s default password is admin. To secure the Access Point, change the AP’s Password from its default.Navigating the UtilityThere are four main tabs: Setup, Wireless, Administration, and Status. Additional screens will be available from most of the main tabs.SetupEnter the network and AP mode settings for the Access Point.•Network Setup. Enter the settings for the Access Point and your Internet connection on this screen.•AP Mode. Set up how the Access Point will work with other access points in your network.HAVE YOU:Enabled TCP/IP on your PCs? PCs communicate over the network with this protocol. Refer to “Appendix D: Windows Help” for more information on TCP/IP.NOTE: The Access Point is designed to function properly after using the Setup Wizard. This chapter is provided solely for those who wish to perform more advanced configuration or monitoring.browser: an application that provides a way to look at and interact with all the information on the World Wide Web. tcp/ip: a set of instructions PCs use to communicate over a network.
37Chapter 7: Configuring the Wireless-G Access PointNavigating the UtilityWireless-G Access PointWirelessYou will use the Wireless tabs to enter a variety of wireless settings for the Access Point.•Basic Wireless Settings. Enter the network mode, SSID, and other basic settings on this screen.•Wireless Security. Use this screen to configure the Access Point’s wireless security settings.•Wireless MAC Filter. From this screen, you can allow or block access to your wireless network.•Advanced Wireless Settings. Configure the Access Point’s more advanced wireless settings.AdministrationYou will use the Administration tabs to manage the Access Point.•Management. This screen allows you to customize the password settings, as well as back up or restore the Access Point’s configuration file.•SNMP. Configure the Simple Network Management Protocol (SNMP) settings on this screen.•Log. Configure the Log settings for the Access Point on this screen.•Factory Defaults. Use this screen to reset the Access Point to its factory default settings.•Firmware Upgrade. Upgrade the Access Point’s firmware on this screen.StatusYou will be able to view status information for your local and wireless network.•Local Network. This screen will display current information on the Access Point and its local network.•Wireless Network. This screen will display current information on the Access Point and its wireless network.firmware: the programming code that runs a networking device.snmp: the standard e-mail protocol on the Internet.
38Chapter 7: Configuring the Wireless-G Access PointAccessing the UtilityWireless-G Access PointAccessing the UtilityTo access the Web-based Utility of the Access Point, launch Internet Explorer or Netscape Navigator. In the Address field, enter the Access Point’s default IP address, 192.168.1.245, or the IP address you entered during the Setup Wizard. (Should you need to learn what IP address the Access Point presently uses, run the Setup Wizard again. It will scan the Access Point and give you its IP address.) Press the Enter key.The login screen will appear. Enter admin in the User Name field. The first time you open the Web-based Utility, use the default password, admin. (You can set a new password from the Administration - Management tab.) Then click the OK button.The Setup - Network Setup TabThe first screen that appears is the Network Setup screen. This allows you to change the Access Point's general settings.Network SetupDevice NameYou may assign any Device Name to the Access Point. Unique, memorable names are helpful, especially if you are employing multiple access points on the same network.Configuration TypeSelect Automatic Configuration - DHCP if your network router will assign an IP address to the Access Point.The Access Point’s IP Address, Subnet Mask, and Default Gateway address are displayed here.Figure 7-1: Login ScreenFigure 7-2: Setup - Automatic Configuration - DHCP Screen
39Chapter 7: Configuring the Wireless-G Access PointThe Setup - Network Setup TabWireless-G Access PointSelect Static IP if you want to assign a static or fixed IP address to the Access Point. Then complete the following:IP Address. The IP address must be unique to your network. We suggest you use the default IP address of 192.168.1.245.Subnet Mask. The Subnet Mask must be the same as that set on your Ethernet network.Default Gateway. Enter the IP address of your network’s gateway. The gateway is the device that enables communication between your computers and the Internet. In most cases, your router acts as your gateway.Change these settings as described here and click Save Settings to apply your changes, or click CancelChanges to cancel your changes. Click Help for more information. Figure 7-3: Setup - Static IP Screenstatic ip address: a fixed address assigned to a computer or device that is connected to a network.
40Chapter 7: Configuring the Wireless-G Access PointThe Setup - AP Mode TabWireless-G Access PointThe Setup - AP Mode TabOn this screen you can change the Access Point’s mode of operation. In most cases, you can keep the default, Access Point. You may wish to change the Access Point’s mode of operation if you want to use the Access Point as a wireless repeater to extend the range of your wireless network. You may also wish to change the Access Point’s mode of operation if you want to use the Access Point as a wireless bridge; for example, you can use two Access Points in Wireless Bridge mode to connect two wired networks that are in two different buildings.AP ModeThe Access Point offers four modes of operation: Access Point, AP Client, Wireless Repeater, and Wireless Bridge. For the Repeater and Bridge modes, make sure the SSID, channel, and security settings are the same for the other wireless access points/devices.LAN MAC AddressThe MAC address of the Access Point is displayed here.Access Point. The Mode is set to Access Point by default. This connects your wireless PCs to a wired network. In most cases, no change is necessary. AP (Access Point) Client. When set to AP Client mode, the AP Client is able to talk to one remote access point within its range. This feature only works with another Wireless-G Access Point (model number: WAP54G).This mode allows the AP Client to act as a client of a remote access point. The AP Client cannot communicate directly with any wireless clients. A separate network attached to the AP Client can then be wirelessly bridged to the remote access point. To use this mode, select AP Client and enter the LAN MAC address of the remote access point in the Remote Access Point’s LAN MAC Address field. If you do not know the remote access point’s MAC address, click the Site Survey button. Select the access point you want to use and click the Close button. If you do not see the access point you want, click the Refresh button to search for access points again.IMPORTANT: For the AP Client and Wireless Bridge modes, the remote access point must be a second Linksys Wireless-G Access Point (model number: WAP54G). For the Wireless Repeater mode, the remote wireless bridge must be a second Linksys Wireless-G Access Point (model number: WAP54G) or Wireless-G Router (model number: WRT54G).Figure 7-4: Setup - AP Mode ScreenFigure 7-5: Site Survey Screen
41Chapter 7: Configuring the Wireless-G Access PointThe Setup - AP Mode TabWireless-G Access PointWireless Repeater. When set to Wireless Repeater mode, the Wireless Repeater is able to talk to up a remote access point within its range and retransmit its signal. This feature only works with the Linksys Wireless-G Router (model number: WRT54G) or another Wireless-G Access Point (model number: WAP54G).To configure a Wireless Repeater environment, select Wireless Repeater and enter the MAC address of the remote access point in the Remote Access Point’s LAN MAC Address field.Figure 7-6: Wireless Repeater Diagram
42Chapter 7: Configuring the Wireless-G Access PointThe Setup - AP Mode TabWireless-G Access PointWireless Bridge. This mode connects two physically separated wired networks using two access points (use additional access points to connect more wired networks). This feature only works with another Wireless-G Access Point (model number: WAP54G).To configure a Wireless Bridge environment, select Wireless Bridge, and enter the MAC addresses of the wireless bridges/access points in the Remote Wireless Bridge’s LAN MAC Addresses fields. You will also need to set the remote wireless bridges/access points to Wireless Bridge mode.Change these settings as described here and click Save Settings to apply your changes, or click CancelChanges to cancel your changes. Click Help for more information.IMPORTANT: In Wireless Bridge mode, the Access Point can ONLY be accessed by another access point in Wireless Bridge mode. In order for your other wireless devices to access the Access Point, you must reset it to Access Point mode. The two modes are mutually exclusive. Figure 7-7: Wireless Bridge Diagram
43Chapter 7: Configuring the Wireless-G Access PointThe Wireless - Basic Wireless Settings TabWireless-G Access PointThe Wireless - Basic Wireless Settings TabChange the wireless network settings on this screen.Basic Wireless SettingsConfigure the Access Point using the available settings.Mode. Select Mixed and both Wireless-G and Wireless-B computers will be allowed on the network, but the speed will be reduced. Select G-Only for maximum speed with Wireless-G products only. The final selection, B-Only, allows only Wireless-B products on the network. To disable wireless performance, select Disabled.Network Name (SSID). Enter the name of the Access Point’s wireless network.Channel. Select the appropriate channel from the list provided; this will be the channel that all of your wireless devices will use.SSID Broadcast. This feature allows the SSID to be broadcast by the Access Point. You may want to enable this function while configuring your network, but make sure that you disable it when you are finished. With this enabled, someone could easily obtain the SSID information with site survey software and gain unauthorized access to your main network. Click Enabled to broadcast the SSID to all wireless devices in range. Click Disabled to increase network security and block the SSID from being seen on networked PCs.Current Encryption. This shows the encryption method currently used by the Access Point.SecureEasySetup Button. The status of the Access Point’s SecureEasySetup feature is displayed here. If you want to use the Access Point’s SecureEasySetup feature, click the SecureEasySetup button.You will be asked to press the SecureEasySetup button (hardware or software) on your wireless client (computer or other network device) within two minutes to complete the SecureEasySetup process. Click the OK button to continue.Figure 7-8: Wireless - Basic Wireless Settings ScreenNOTE: SecureEasySetup uses WPA Personal encryption. If your current wireless devices do not support WPA Personal security, then you cannot use SecureEasySetup on your network. You will need to manually configure your network security using the encryption supported by your existing devices.Figure 7-9: Press the SecureEasySetup Button for Your Wireless ClientNOTE: If you have already set up your network using your router’s SecureEasySetup feature, then you cannot use the Access Point’s SecureEasySetup feature. You must manually configure the Access Point’s wireless settings to match your existing network’s settings.
44Chapter 7: Configuring the Wireless-G Access PointThe Wireless - Basic Wireless Settings TabWireless-G Access PointA new screen will be displayed while the Access Point is waiting for you to push the SecureEasySetup button on your wireless client.When the SecureEasySetup process is complete, the Basic Wireless Settings screen will appear, and the Current Encryption and Status information will be updated.Reset Security. If you already set up the network using the Access Point’s SecureEasySetup feature and you want to replace your current settings with new SecureEasySetup settings, click the Reset Security button. A new screen will appear. You will be asked to confirm that you want to reset your wireless security settings. Click the OK button to continue.The Access Point will generate a new network name (SSID) and set of keys. To configure your wireless network using SecureEasySetup, return to the previous page of this User Guide and follow the instructions for the SecureEasySetup button.Change these settings as described here and click Save Settings to apply your changes, or click CancelChanges to cancel your changes. Click Help for more information.NOTE: You can only add one SecureEasySetup device at a time. For additional devices, click the SecureEasySetup button on the Basic Wireless Settings screen and repeat the process.Figure 7-11: SecureEasySetup Completed ScreenFigure 7-12: Confirm ResetFigure 7-10: Waiting for Completion of SecureEasySetup
45Chapter 7: Configuring the Wireless-G Access PointThe Wireless - Wireless Security TabWireless-G Access PointThe Wireless - Wireless Security TabChange the Access Point’s wireless security settings on this screen.Wireless SecuritySecurity Mode. Select the security method you want to use, WPA-Personal,WPA2-Personal,WPA2-Mixed,WPA-Enterprise,RADIUS, or WEP. (WPA stands for Wi-Fi Protected Access, which is a security standard stronger than WEP encryption. WPA2 is a stronger version of WPA. WEP stands for Wired Equivalent Privacy, while RADIUS stands for Remote Authentication Dial-In User Service.) Refer to the appropriate instructions below. For detailed instructions on configuring wireless security for the Access Point, turn to “Appendix B: Wireless Security.” To disable such security, select Disabled.WPA-PersonalEncryption. WPA offers you two encryption methods, TKIP and AES, with dynamic encryption keys. Select the type of algorithm you want to use, TKIP or AES.Passphrase. Enter a Passphrase (also called a WPA Shared Key) of 8-32 characters. Key Renewal. Enter a Key Renewal timeout period, which instructs the Access Point how often it should change the encryption keys.Change these settings as described here and click Save Settings to apply your changes, or click CancelChanges to cancel your changes. Click Help for more information.WPA2-PersonalEncryption.AES is automatically selected as the encryption method.Passphrase. Enter a Passphrase (also called a WPA Shared Key) of 8-32 characters. Key Renewal. Enter a Key Renewal timeout period, which instructs the Access Point how often it should change the encryption keys.Change these settings as described here and click Save Settings to apply your changes, or click CancelChanges to cancel your changes. Click Help for more information.encryption: encoding data transmitted in a network.Figure 7-13: Wireless - Wireless Security (WPA-Personal) ScreenFigure 7-14: Wireless Security - WPA2-Personal Screen
46Chapter 7: Configuring the Wireless-G Access PointThe Wireless - Wireless Security TabWireless-G Access PointWPA2-MixedEncryption.TKIP + AES is automatically selected so both methods can be used.Passphrase. Enter a Passphrase (also called a WPA Shared Key) of 8-32 characters. Key Renewal. Enter a Key Renewal timeout period, which instructs the Access Point how often it should change the encryption keys.Change these settings as described here and click Save Settings to apply your changes, or click CancelChanges to cancel your changes. Click Help for more information.WPA-EnterpriseThis option features WPA used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Access Point.)Encryption. WPA offers you two encryption methods, TKIP and AES, with dynamic encryption keys. Select the type of algorithm you want to use, TKIP or AES.RADIUS Server. Enter the RADIUS server’s IP address.RADIUS Port. Enter the port number used by the RADIUS server.Shared Secret. Enter the Shared Secret key used by the Access Point and RADIUS server.Key Renewal. Enter a Key Renewal timeout period, which instructs the Access Point how often it should change the encryption keys.Change these settings as described here and click Save Settings to apply your changes, or click CancelChanges to cancel your changes. Click Help for more information.Figure 7-16: Wireless Security - WPA-Enterprise ScreenFigure 7-15: Wireless Security - WPA2-Mixed Screenradius: a protocol that uses an authentication server to control network access.server: any computer whose function in a network is to provide user access to files, printing, communications, and other services.
47Chapter 7: Configuring the Wireless-G Access PointThe Wireless - Wireless Security TabWireless-G Access PointRADIUSThis option features WEP used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Access Point.)RADIUS Server. Enter the RADIUS server’s IP address.RADIUS Port. Enter the port number used by the RADIUS server.Shared Secret. Enter the Shared Secret key used by the Access Point and RADIUS server.Encryption. Select a level of WEP encryption, 40/64 bits (10 hex digits) or 128 bits (26 hex digits).Passphrase. To generate WEP keys using a Passphrase, enter the Passphrase and click the Generate key.Key 1-4. If you want to manually enter WEP keys, then complete the fields provided. Each WEP key can consist of the letters “A” through “F” and the numbers “0” through “9”. It should be 10 characters in length for 64-bit encryption or 26 characters in length for 128-bit encryption.TX Key. Select which Key to use for data transmissions.Change these settings as described here and click Save Settings to apply your changes, or click CancelChanges to cancel your changes. Click Help for more information.WEPEncryption. Select a level of WEP encryption, 40/64 bits (10 hex digits) or 128 bits (26 hex digits).Passphrase. To generate WEP keys using a Passphrase, enter the Passphrase and click the Generate key.Key 1-4. If you want to manually enter WEP keys, then complete the fields provided. Each WEP key can consist of the letters “A” through “F” and the numbers “0” through “9”. It should be 10 characters in length for 64-bit encryption or 26 characters in length for 128-bit encryption.TX Key. Select which Key to use for data transmissions.Change these settings as described here and click Save Settings to apply your changes, or click CancelChanges to cancel your changes. Click Help for more information.Figure 7-17: Wireless Security - RADIUS ScreenFigure 7-18: Wireless Security - WEP Screen
48Chapter 7: Configuring the Wireless-G Access PointThe Wireless - Wireless MAC Filter TabWireless-G Access PointThe Wireless - Wireless MAC Filter TabThis screen allows you to permit or block wireless access for computers with specific MAC addresses.Wireless MAC FilterAccess RestrictionIf you want to control access to your wireless network, select Enable. If you do not wish to filter users by MAC address, select Disable.To deny access, click Prevent PCs listed below from accessing the wireless network. To permit access, click Permit PCs listed below to access the wireless network.MAC 01-25. Enter the MAC addresses of the computers whose access you want to control. If you want to list more than 25 MAC addresses, then select MAC Addresses 26~50 from the drop-down menu.Click Clear to delete the MAC addresses you have entered.Change these settings as described here and click Save Settings to apply your changes, or click CancelChanges to cancel your changes. Click Help for more information. Figure 7-19: Wireless - Wireless MAC Filter Screenmac address: the unique address that a manufacturer assigns to each networking device.
49Chapter 7: Configuring the Wireless-G Access PointThe Wireless - Advanced Wireless Settings TabWireless-G Access PointThe Wireless - Advanced Wireless Settings TabThis screen allows you to configure the advanced settings for the Access Point. In most cases, these settings do not need to be changed.Advanced WirelessYou can change the data transmission and output power settings for the Access Point.Authentication Type. Select the authentication method you want the Access Point to use, Shared Key or Open System (Default). Shared Key is when both the sender and the recipient share a WEP key for authentication. Open System is when the sender and the recipient do not share a WEP key for authentication. All devices on your network must use the same authentication type. In most cases, keep the default, Open System (Default).Basic Rates. This setting is not actually one rate of transmission but a series of rates that are advertised to the other wireless devices in your network, so they know at which rates the Access Point can transmit. At the Defaultsetting, the Access Point will advertise that it will automatically select the best rate for transmission. Other options are 1-2Mbps, for use with older wireless technology, and All, when you wish to have all rates advertised. The Basic Data Rates are not the rates transmitted; the rates transmitted can be configured through the Transmission Rates setting on this screen.Transmission Rates. The range is from 1 to 54Mbps. The rate of data transmission should be set depending on the speed of your wireless network. You can select from a range of transmission speeds, or you can keep the default setting, Auto (Default), to have the Access Point automatically use the fastest possible data rate and enable the Auto-Fallback feature. Auto-Fallback will negotiate the best possible connection speed between the Access Point and a wireless client.Transmission Power. You can adjust the output power of the Access Point to get the appropriate coverage for your wireless network. Select the level you need for your environment. If you are not sure which setting to choose, then keep the default setting, Full (Default).CTS Protection Mode. The CTS (Clear-To-Send) Protection Mode function boosts the Access Point’s ability to catch all Wireless-G transmissions but will severely decrease performance. Select Enable if you want to permanently enable this feature, or keep the default, Disable, if you want to permanently disable this feature. In most cases, CTS Protection Mode should remain disabled, unless the Wireless-G products are experiencing severe problems trying to transmit to the Access Point in an environment with heavy 802.11b traffic.Frame Burst Mode. Enabling this option should reduce overhead and enhance your network performance, depending on the manufacturer of your wireless products. If you are not sure how to use this option, keep the default, Disabled.Figure 7-20: Wireless - Advanced Wireless Settings Screencts (clear-to-send): a signal sent by a wireless device, signifying that it is ready to receive data.
50Chapter 7: Configuring the Wireless-G Access PointThe Wireless - Advanced Wireless Settings TabWireless-G Access PointAntenna Selection. This selection is for choosing which antenna transmits data, left or right. If you are not sure which antenna to use, keep the default, Diversity, to increase reception.Beacon Interval. This value indicates the frequency interval of the beacon. A beacon is a packet broadcast by the Access Point to keep the network synchronized. A beacon includes the wireless networks service area, the Access Point address, the Broadcast destination addresses, a time stamp, Delivery Traffic Indicator Maps, and the Traffic Indicator Message (TIM).DTIM Interval. This value indicates how often the Access Point sends out a Delivery Traffic Indication Message (DTIM). Lower settings result in more efficient networking, while preventing your PC from dropping into power-saving sleep mode. Higher settings allow your PC to enter sleep mode, thus saving power, but interferes with wireless transmissions.Fragmentation Threshold. This specifies the maximum size a data packet can be before splitting and creating a new packet. It should remain at its default setting of 2346. A smaller setting means smaller packets, which will create more packets for each transmission. If you have decreased this value and experience high packet error rates, you can increase it again, but it will likely decrease overall network performance. Only minor modifications of this value are recommended.RTS Threshold. This setting determines how large a packet can be before the Access Point coordinates transmission and reception to ensure efficient communication. This value should remain at its default setting of 2347. Should you encounter inconsistent data flow, only minor modifications are recommended.Change these settings as described here and click Save Settings to apply your changes, or click CancelChanges to cancel your changes. Click Help for more information.fragmentation: breaking a packet into smaller units when transmitting over a network.dtim (delivery traffic indication message): a message included in data packets that can increase wireless efficiency.beacon internal: data transmitted on your wireless network that keeps the network synchronized.packet: a unit of data sent over a network.rts (request to send): a networking method of coordinating large packets through the RTS Threshold setting.
51Chapter 7: Configuring the Wireless-G Access PointThe Administration - Management TabWireless-G Access PointThe Administration - Management TabOn this screen you can configure the password as well as back up or restore the Access Point’s configuration file.ManagementYou should change the password that controls access to the Access Point’s Web-based Utility.AP’s PasswordPassword. Create a Password for the Access Point’s Web-based Utility.Re-enter to Confirm. To confirm the new Password, enter it again in this field.Backup and RestoreOn this screen you can create a backup configuration file or save a configuration file to the Access Point.Backup Settings. To save a backup configuration file on a computer, click the Backup Settings button and follow the on-screen instructions.Restore Settings. To upload a configuration file to the Access Point, click the Restore Settings button and follow the on-screen instructions.Change these settings as described here and click Save Settings to apply your changes, or click CancelChanges to cancel your changes. Click Help for more information.Figure 7-21: Administration - Management Screen
52Chapter 7: Configuring the Wireless-G Access PointThe Administration - SNMP TabWireless-G Access PointThe Administration - SNMP TabSNMP is a popular network monitoring and management protocol. It provides network administrators with the ability to monitor the status of the Access Point and receive notification of any critical events as they occur on the Access Point.SNMP V1/V2cTo enable the SNMP support feature, select Enable. Otherwise, select Disable.Contact. Enter the name of the contact person, such as a network administrator, for the Access Point.Device Name. Enter the name you wish to give to the Access Point.Location. Enter the location of the Access Point.SNMP CommunityYou can have up to two passwords. Then select the level of access you want to assign to each password.(public.) Enter the first password that allows access to the Access Point’s SNMP information. The default is public. Then select the level of access you want to assign, Read-Only or Read/Write.(private.) Enter the second password that allows access to the Access Point’s SNMP information. The default is private. Then select the level of access you want to assign, Read-Only or Read/Write.Change these settings as described here and click Save Settings to apply your changes, or click CancelChanges to cancel your changes. Click Help for more information.Figure 7-22: Administration - SNMP Screen
53Chapter 7: Configuring the Wireless-G Access PointThe Administration - Log TabWireless-G Access PointThe Administration - Log TabOn this screen you can configure the log settings.ManagementYou can have logs that keep track of the Access Point’s activities.LogTo enable the Log support feature, select Enabled. Otherwise, select Disabled.Logviewer IP Address. If you have chosen to monitor the Access Point’s traffic, then you can designate a PC that will receive permanent log files periodically. In the field provided, enter the IP address of this PC. To view these permanent logs, you must use Logviewer software, which can be downloaded free of charge from www.linksys.com.View Log. To see a temporary log of the Access Point’s most recent activities, click this button.On the View Log screen, click the First Page button to see the first page of log entries. Click the Last Page button to see the last page of log entries. Click the Previous Page button to see the previous page of log entries, and click the Next Page button to see the next page of log entries. To delete all log entries, click the Clear Logbutton. To update the log with the most recent activities, click the Refresh button.Change these settings as described here and click Save Settings to apply your changes, or click CancelChanges to cancel your changes. Click Help for more information.Figure 7-24: View Log ScreenFigure 7-23: Administration - Log Screen
54Chapter 7: Configuring the Wireless-G Access PointThe Administration - Factory Defaults TabWireless-G Access PointThe Administration - Factory Defaults TabOn this screen you can restore the Access Point’s factory default settings.ManagementWrite down any custom settings before you restore the factory defaults. Once the Access Point is reset, you will have to re-enter all of your configuration settings.Factory DefaultsRestore Factory Defaults. To restore the Access Point's factory default settings, click this button. Then follow the on-screen instructions.Click Help for more information.The Administration - Firmware Upgrade TabOn this screen you can upgrade the Access Point’s firmware. Do not upgrade the firmware unless you are experiencing problems with the Access Point or the new firmware has a feature you want to use.Firmware UpgradeBefore you upgrade the Access Point’s firmware, write down all of your custom settings. After you upgrade its firmware, you will have to re-enter all of your configuration settings. To upgrade the Access Point’s firmware:1. Download the firmware upgrade file from the Linksys website, www.linksys.com.2. Extract the firmware upgrade file on your computer.3. On the Firmware Upgrade screen, enter the location of the firmware upgrade file in the field provided, or click the Browse button to find the file.4. Click the Upgrade button, and follow the on-screen instructions. You can also click the Cancel button to cancel the upgrade, or click the Help button for more information.Click Help for more information.Figure 7-25: Administration - Factory Defaults ScreenFigure 7-26: Administration - Firmware Upgrade Screenupgrade: to replace existing software or firmware with a newer version
55Chapter 7: Configuring the Wireless-G Access PointThe Status - Local Network TabWireless-G Access PointThe Status - Local Network TabThe Local Network screen displays the Access Point’s current status information for the local network.AP’s InformationFirmware Version. This is the version of the Access Point’s current firmware.Local NetworkMAC Address. The MAC address of the Access Point’s Local Area Network (LAN) interface is displayed here.AP’s IP Address. This shows the Access Point’s IP Address, as it appears on your local network.Subnet Mask. This shows the Access Point’s Subnet Mask.Default Gateway. Displayed here is the IP address of the Access Point’s Default Gateway.Click Help for more information.Figure 7-27: Status - Local Network Screen
56Chapter 7: Configuring the Wireless-G Access PointThe Status - Wireless Network TabWireless-G Access PointThe Status - Wireless Network TabThe Wireless Network screen displays the Access Point’s current status information for its wireless network.Wireless NetworkMAC Address. The MAC Address of the Access Point’s wireless interface is displayed here.Mode. The Access Point’s mode is displayed here.Network Name (SSID). The Access Point’s main SSID is displayed here.Channel. The Access Point’s Channel setting for wireless broadcast is shown here.Security. The wireless security setting for the Access Point is displayed here.SSID Broadcast. Shown here is the setting of the Access Point’s SSID Broadcast feature.Click Help for more information.Figure 7-28: Status - Wireless Network Screen
57Appendix A: TroubleshootingFrequently Asked QuestionsWireless-G Access PointAppendix A: TroubleshootingThis appendix provides solutions to problems that may occur during the installation and operation of the Wireless-G Access Point. Read the description below to solve your problems. If you can't find an answer here, check the Linksys website at www.linksys.com.Frequently Asked QuestionsCan the Access Point act as my DHCP server?No. The Access Point is nothing more than a wireless hub, and as such cannot be configured to handle DHCP capabilities.Can I run an application from a remote computer over the wireless network?This will depend on whether or not the application is designed to be used over a network. Consult the application’s user guide to determine if it supports operation over a network.Can I play multiplayer games with other users of the wireless network?Yes, as long as the game supports multiple players over a LAN (local area network). Refer to the game’s user guide for more information.What is the IEEE 802.11b standard?It is one of the IEEE standards for wireless networks. The 802.11b standard allows wireless networking hardware from different manufacturers to communicate, provided that the hardware complies with the 802.11b standard. The 802.11b standard states a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz.What is the IEEE 802.11g standard?It is one of the IEEE standards for wireless networks. The 802.11g standard allows wireless networking hardware from different manufacturers to communicate, provided that the hardware complies with the 802.11g standard. The 802.11g standard states a maximum data transfer rate of 54Mbps and an operating frequency of 2.4GHz.What IEEE 802.11b features are supported?The product supports the following IEEE 802.11 functions: • CSMA/CA plus Acknowledge protocol • Multi-Channel Roaming • Automatic Rate Selection • RTS/CTS feature • Fragmentation • Power Management
58Appendix A: TroubleshootingFrequently Asked QuestionsWireless-G Access PointWhat IEEE 802.11g features are supported?The product supports the following IEEE 802.11g functions: • CSMA/CA plus Acknowledge protocol • OFDM protocol• Multi-Channel Roaming • Automatic Rate Selection • RTS/CTS feature • Fragmentation• Power Management What is Ad-hoc? An Ad-hoc wireless LAN is a group of computers, each with a WLAN adapter, connected as an independent wireless LAN. An Ad-hoc wireless LAN is applicable at a departmental scale for a branch or SOHO operation.What is Infrastructure?An integrated wireless and wired LAN is called an Infrastructure configuration. Infrastructure is applicable to enterprise scale for wireless access to a central database, or wireless application for mobile workers.What is roaming?Roaming is the ability of a portable computer to communicate continuously while its user is moving freely throughout an area greater than that covered by a single Access Point. Before using the roaming function, the user must make sure that the computer is set to the same channel number as the Access Point of the dedicated coverage area. To achieve true seamless connectivity, the wireless LAN must incorporate a number of different functions. Each node and Access Point, for example, must always acknowledge receipt of each message. Each node must maintain contact with the wireless network even when not actually transmitting data. Achieving these functions simultaneously requires a dynamic RF networking technology that links Access Points and nodes. In such a system, the user’s end node undertakes a search for the best possible access to the system. First, it evaluates such factors as signal strength and quality, as well as the message load currently being carried by each Access Point and the distance of each Access Point to the wired backbone. Based on that information, the node next selects the right Access Point and registers its address. Communications between end node and host computer can then be transmitted up and down the backbone.As the user moves on, the end node’s RF transmitter regularly checks the system to determine whether it is in touch with the original Access Point or whether it should seek a new one. When a node no longer receives acknowledgment from its original Access Point, it undertakes a new search. Upon finding a new Access Point, it then re-registers, and the communication process continues.
59Appendix A: TroubleshootingFrequently Asked QuestionsWireless-G Access PointWhat is the ISM band?The FCC and their counterparts outside of the U.S. have set aside bandwidth for unlicensed use in the ISM (Industrial, Scientific and Medical) band. Spectrum in the vicinity of 2.4 GHz, in particular, is being made available worldwide. This presents a truly revolutionary opportunity to place convenient high speed wireless capabilities in the hands of users around the globe. What is Spread Spectrum?Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade-off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum (DSSS) and Frequency Hopping Spread Spectrum (FHSS).What is DSSS? What is FHSS? And what are their differences?Frequency Hopping Spread Spectrum (FHSS) uses a narrowband carrier that changes frequency in a pattern that is known to both transmitter and receiver. Properly synchronized, the net effect is to maintain a single logical channel. To an unintended receiver, FHSS appears to be short-duration impulse noise. Direct Sequence Spread Spectrum (DSSS) generates a redundant bit pattern for each bit to be transmitted. This bit pattern is called a chip (or chipping code). The longer the chip, the greater the probability that the original data can be recovered. Even if one or more bits in the chip are damaged during transmission, statistical techniques embedded in the radio can recover the original data without the need for retransmission. To an unintended receiver, DSSS appears as low power wideband noise and is rejected (ignored) by most narrowband receivers. Would the information be intercepted while transmitting on air?WLAN features two-fold protection in security. On the hardware side, as with Direct Sequence Spread Spectrum technology, it has the inherent security feature of scrambling. On the software side, the WLAN series offers a variety of wireless security methods to enhance security and access control. Users can set it up depending upon their needs.Can Linksys wireless products support file and printer sharing?Linksys wireless products perform the same function as LAN products. Therefore, Linksys wireless products can work with NetWare, Windows NT/2000, or other LAN operating systems to support printer or file sharing.What is WEP?WEP is Wired Equivalent Privacy, a data privacy mechanism based on a 40-bit shared-key algorithm, as described in the IEEE 802.11 standard.
60Appendix A: TroubleshootingFrequently Asked QuestionsWireless-G Access PointWhat is a MAC Address? The Media Access Control (MAC) address is a unique number assigned by the manufacturer to any Ethernet networking device, such as a network adapter, that allows the network to identify it at the hardware level. For all practical purposes, this number is usually permanent. Unlike IP addresses, which can change every time a computer logs on to the network, the MAC address of a device stays the same, making it a valuable identifier for the network.How do I avoid interference?Using multiple Access Points on the same channel and in close proximity to one another will generate interference. When employing multiple Access Points, make sure to operate each one on a different channel (frequency).How do I reset the Access Point?Press the Reset button on the back of the Access Point for about ten seconds. This will reset the unit to its default settings.How do I resolve issues with signal loss?There is no way to know the exact range of your wireless network without testing. Every obstacle placed between an Access Point and wireless PC will create signal loss. Leaded glass, metal, concrete floors, water, and walls will inhibit the signal and reduce range. Start with your Access Point and your wireless PC in the same room and move it away in small increments to determine the maximum range in your environment. You may also try using different channels, as this may eliminate interference affecting only one channel. Also, open the Access Point’s Web-based Utility. Click the Wireless tab and then the Advanced Wireless tab. Make sure the Output Power is set to 100%.Does the Access Point function as a firewall?No. The Access Point is only a bridge from wired Ethernet to wireless clients. I have excellent signal strength, but I cannot see my network. Wireless security, such as WEP or WPA, is probably enabled on the Access Point, but not on your wireless adapter (or vice versa). Verify that the same wireless security settings are being used on all devices in your wireless network. What is the maximum number of users the Access Point can handle?No more than 65, but this depends on the volume of data and may be fewer if many users create a large amount of network traffic.
61Appendix B: Wireless SecuritySecurity PrecautionsWireless-G Access PointAppendix B: Wireless SecurityLinksys wants to make wireless networking as safe and easy for you as possible. The current generation of Linksys products provide several network security features, but they require specific action on your part for implementation. So, keep the following in mind whenever you are setting up or using your wireless network.Security PrecautionsThe following is a complete list of security precautions to take (as shown in this User Guide) (at least steps 1 through 5 should be followed):1. Change the default SSID. 2. Disable SSID Broadcast. 3. Change the default password for the Administrator account. 4. Enable MAC Address Filtering. 5. Change the SSID periodically. 6. Use the highest encryption algorithm possible. Use WPA if it is available. Please note that this may reduce your network performance. 7. Change the WEP encryption keys periodically. To ensure network security, steps one through five should be followed, at least.Security Threats Facing Wireless Networks Wireless networks are easy to find. Hackers know that in order to join a wireless network, wireless networking products first listen for “beacon messages”. These messages can be easily decrypted and contain much of the network’s information, such as the network’s SSID (Service Set Identifier). Here are the steps you can take:Change the administrator’s password regularly. With every wireless networking device you use, keep in mind that network settings (SSID, WEP keys, etc.) are stored in its firmware. Your network administrator is the only person who can change network settings. If a hacker gets a hold of the administrator’s password, he, too, can change those settings. So, make it harder for a hacker to get that information. Change the administrator’s password regularly.NOTE: Some of these security features are available only through the network router or access point. Refer to the router or access point’s documentation for more information.
62Appendix B: Wireless SecuritySecurity Threats Facing Wireless NetworksWireless-G Access PointSSID. There are several things to keep in mind about the SSID: 1. Disable Broadcast 2. Make it unique 3. Change it often Most wireless networking devices will give you the option of broadcasting the SSID. While this option may be more convenient, it allows anyone to log into your wireless network. This includes hackers. So, don’t broadcast the SSID.Wireless networking products come with a default SSID set by the factory. (The Linksys default SSID is “linksys”.) Hackers know these defaults and can check these against your network. Change your SSID to something unique and not something related to your company or the networking products you use.Change your SSID regularly so that any hackers who have gained access to your wireless network will have to start from the beginning in trying to break in.MAC Addresses. Enable MAC Address filtering. MAC Address filtering will allow you to provide access to only those wireless nodes with certain MAC Addresses. This makes it harder for a hacker to access your network with a random MAC Address. WEP Encryption. Wired Equivalent Privacy (WEP) is often looked upon as a cure-all for wireless security concerns. This is overstating WEP’s ability. Again, this can only provide enough security to make a hacker’s job more difficult.There are several ways that WEP can be maximized:1. Use the highest level of encryption possible 2. Use “Shared Key” authentication3. Change your WEP key regularly WPA. Wi-Fi Protected Access (WPA) is the newest and best available standard in Wi-Fi security. Four modes are available: WPA-Personal, WPA2-Personal, WPA-Enterprise, and RADIUS. WPA-Personal gives you a choice of two encryption methods: TKIP (Temporal Key Integrity Protocol), which utilizes a stronger encryption method and incorporates Message Integrity Code (MIC) to provide protection against hackers, and AES (Advanced Encryption Standard), which utilizes a symmetric 128-Bit block data encryption. WPA2-Personal only uses AES encryption, which is stronger than TKIP. WPA-Enterprise offers two encryption methods, TKIP and AES, with dynamic encryption keys. RADIUS (Remote Authentication Dial-In User Service) utilizes a RADIUS server for authentication. IMPORTANT: Always remember that each device in your wireless network MUST use the same encryption method and encryption key or your wireless network will not function properly.
63Appendix B: Wireless SecuritySecurity Threats Facing Wireless NetworksWireless-G Access PointWPA-Personal. If you do not have a RADIUS server, select the type of algorithm you want to use, TKIP or AES, and enter a password in the Passphrase field of 8-63 characters.WPA2-Personal. Enter a password in the Passphrase field of 8-63 characters.WPA-Enterprise. WPA used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router or other device.) WPA-Enterprise offers two encryption methods, TKIP and AES, with dynamic encryption keys. Enter the RADIUS server’s IP Address and port number, along with a key shared between the device and the server. Last, enter a Group Key Renewal period, which instructs the device how often it should change the encryption keys.RADIUS. WEP used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router or other device.) First, enter the RADIUS server’s IP Address and port number, along with a key shared between the device and the server. Then, select a WEP key and a level of WEP encryption, and either generate a WEP key through the Passphrase or enter the WEP key manually.Implementing encryption may have a negative impact on your network’s performance, but if you are transmitting sensitive data over your network, encryption should be used. These security recommendations should help keep your mind at ease while you are enjoying the most flexible and convenient technology Linksys has to offer.
64Appendix C: Upgrading FirmwareWireless-G Access PointAppendix C: Upgrading FirmwareThe Access Point's firmware is upgraded through the Web-based Utility’s Administration - Firmware Upgrade tab. Follow these instructions:1. Download the firmware upgrade file from the Linksys website, www.linksys.com.2. Extract the firmware upgrade file on your computer.3. Open the Access Point’s Web-based Utility.4. Click the Administration tab.5. Click the Upgrade Firmware tab.6. On the Firmware Upgrade screen, enter the location of the firmware upgrade file in the field provided, or click the Browse button to find the file.7. Click the Upgrade button, and follow the on-screen instructions.Figure C-1: Firmware Upgrade
65Appendix D: Windows HelpWireless-G Access PointAppendix D: Windows HelpAlmost all wireless products require Microsoft Windows. Windows is the most used operating system in the world and comes with many features that help make networking easier. These features can be accessed through Windows Help and are described in this appendix.TCP/IPBefore a computer can communicate with the Access Point, TCP/IP must be enabled. TCP/IP is a set of instructions, or protocol, all PCs follow to communicate over a network. This is true for wireless networks as well. Your PCs will not be able to utilize wireless networking without having TCP/IP enabled. Windows Help provides complete instructions on enabling TCP/IP.Shared ResourcesIf you wish to share printers, folder, or files over your network, Windows Help provides complete instructions on utilizing shared resources.Network Neighborhood/My Network PlacesOther PCs on your network will appear under Network Neighborhood or My Network Places (depending upon the version of Windows you're running). Windows Help provides complete instructions on adding PCs to your network.
66Appendix E: GlossaryWireless-G Access PointAppendix E: Glossary802.11b - A wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz.802.11g - A wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of 2.4GHz, and backward compatibility with 802.11b devices.Access Point - A device that allows wireless-equipped computers and other devices to communicate with a wired network. Also used to expand the range of a wireless network.Adapter - A device that adds network functionality to your PC.Ad-hoc - A group of wireless devices communicating directly with each other (peer-to-peer) without the use of an access point.AES (Advanced Encryption Standard) - A security method that uses symmetric 128-bit block data encryption.Backbone - The part of a network that connects most of the systems and networks together, and handles the most data.Bandwidth - The transmission capacity of a given device or network.Beacon Interval - Data transmitted on your wireless network that keeps the network synchronized.Bit - A binary digit.Boot - To start a device and cause it to start executing instructions.Bridge - A device that connects different networks. Broadband - An always-on, fast Internet connection.Browser - An application program that provides a way to look at and interact with all the information on the World Wide Web. Buffer - A shared or assigned memory area that is used to support and coordinate different computing and networking activities so one isn't held up by the other.Byte - A unit of data that is usually eight bits long
67Appendix E: GlossaryWireless-G Access PointCable Modem - A device that connects a computer to the cable television network, which in turn connects to the Internet.CSMA/CA (Carrier SenseMultiple Access/Collision Avoidance) - A method of data transfer that is used to prevent data collisions.CTS (Clear ToSend) - A signal sent by a wireless device, signifying that it is ready to receive data.Daisy Chain - A method used to connect devices in a series, one after the other.Database - A collection of data that is organized so that its contents can easily be accessed, managed, and updated.DDNS (Dynamic Domain Name System) - Allows the hosting of a website, FTP server, or e-mail server with a fixed domain name (e.g., www.xyz.com) and a dynamic IP address.Default Gateway - A device that forwards Internet traffic from your local area network.DHCP (Dynamic Host Configuration Protocol) - A networking protocol that allows administrators to assign temporary IP addresses to network computers by “leasing” an IP address to a user for a limited amount of time, instead of assigning permanent IP addresses.DMZ (Demilitarized Zone) - Removes the Router's firewall protection from one PC, allowing it to be “seen” from the Internet.DNS (Domain Name Server) - The IP address of your ISP's server, which translates the names of websites into IP addresses.Domain - A specific name for a network of computers.Download - To receive a file transmitted over a network. DSL (Digital Subscriber Line) - An always-on broadband connection over traditional phone lines.DSSS (Direct-Sequence Spread-Spectrum) - Frequency transmission with a redundant bit pattern resulting in a lower probability of information being lost in transit.DTIM (Delivery Traffic Indication Message) - A message included in data packets that can increase wireless efficiency.Dynamic IP Address - A temporary IP address assigned by a DHCP server.
68Appendix E: GlossaryWireless-G Access PointEAP (Extensible Authentication Protocol) - A general authentication protocol used to control network access. Many specific authentication methods work within this framework.EAP-PEAP (Extensible Authentication Protocol-Protected Extensible Authentication Protocol) - A mutual authentication method that uses a combination of digital certificates and another system, such as passwords.EAP-TLS (Extensible Authentication Protocol-Transport Layer Security) - A mutual authentication method that uses digital certificates.Encryption - Encoding data transmitted in a network. Ethernet - A networking protocol that specifies how data is placed on and retrieved from a common transmission medium.Finger - A program that tells you the name associated with an e-mail address.Firewall - A set of related programs located at a network gateway server that protects the resources of a network from users from other networks.Firmware - The programming code that runs a networking device.Fragmentation -Breaking a packet into smaller units when transmitting over a network medium that cannot support the original size of the packet. FTP (File Transfer Protocol) - A protocol used to transfer files over a TCP/IP network.Full Duplex - The ability of a networking device to receive and transmit data simultaneously.Gateway - A device that interconnects networks with different, incompatible communications protocols. Half Duplex - Data transmission that can occur in two directions over a single line, but only one direction at a time.Hardware - The physical aspect of computers, telecommunications, and other information technology devices.HTTP (HyperText Transport Protocol) - The communications protocol used to connect to servers on the World Wide Web.Infrastructure - A wireless network that is bridged to a wired network via an access point.IP (Internet Protocol) - A protocol used to send data over a network.IP Address - The address used to identify a computer or device on a network.
69Appendix E: GlossaryWireless-G Access PointIPCONFIG - A Windows 2000 and XP utility that displays the IP address for a particular networking device.IPSec (Internet Protocol Security) - A VPN protocol used to implement secure exchange of packets at the IP layer.ISM band - Radio bandwidth utilized in wireless transmissions.ISP (Internet Service Provider) - A company that provides access to the Internet. LAN - The computers and networking products that make up your local network.LEAP (Lightweight Extensible Authentication Protocol) - A mutual authentication method that uses a username and password system.MAC (Media Access Control) Address - The unique address that a manufacturer assigns to each networking device. Mbps (MegaBits Per Second) - One million bits per second; a unit of measurement for data transmission.mIRC - An Internet Relay Chat program that runs under Windows.Multicasting - Sending data to a group of destinations at once.NAT (Network Address Translation) - NAT technology translates IP addresses of a local area network to a different IP address for the Internet.Network - A series of computers or devices connected for the purpose of data sharing, storage, and/or transmission between users.NNTP (Network News Transfer Protocol) - The protocol used to connect to Usenet groups on the Internet.Node - A network junction or connection point, typically a computer or work station.OFDM (Orthogonal Frequency Division Multiplexing) - Frequency transmission that separates the data stream into a number of lower-speed data streams, which are then transmitted in parallel to prevent information from being lost in transit.Packet - A unit of data sent over a network.Passphrase - Used much like a password, a passphrase simplifies the WEP encryption process by automatically generating the WEP encryption keys for Linksys products.PEAP (Protected Extensible Authentication Protocol) - A mutual authentication method that uses a combination of digital certificates and another system, such as passwords.
70Appendix E: GlossaryWireless-G Access PointPing (Packet INternet Groper) - An Internet utility used to determine whether a particular IP address is online.POP3 (Post Office Protocol 3) - A standard mail server commonly used on the Internet.Port - The connection point on a computer or networking device used for plugging in cables or adapters. Power over Ethernet (PoE) - A technology enabling an Ethernet network cable to deliver both data and power.PPPoE (Point to Point Protocol over Ethernet) - A type of broadband connection that provides authentication (username and password) in addition to data transport.PPTP (Point-to-Point Tunneling Protocol) - A VPN protocol that allows the Point to Point Protocol (PPP) to be tunneled through an IP network. This protocol is also used as a type of broadband connection in Europe.Preamble - Part of the wireless signal that synchronizes network traffic.RADIUS (Remote Authentication Dial-InUser Service) - A protocol that uses an authentication server to control network access.RJ-45 (Registered Jack-45) - An Ethernet connector that holds up to eight wires.Roaming - The ability to take a wireless device from one access point's range to another without losing the connection.Router - A networking device that connects multiple networks together.RTS (Request ToSend) - A networking method of coordinating large packets through the RTS Threshold setting.Server - Any computer whose function in a network is to provide user access to files, printing, communications, and other services. SMTP (Simple Mail Transfer Protocol) - The standard e-mail protocol on the Internet.SNMP (Simple Network Management Protocol) - A widely used network monitoring and control protocol.Software - Instructions for the computer. A series of instructions that performs a particular task is called a “program”.SOHO (Small Office/Home Office) - Market segment of professionals who work at home or in small offices.SPI (Stateful Packet Inspection) Firewall - A technology that inspects incoming packets of information before allowing them to enter the network.
71Appendix E: GlossaryWireless-G Access PointSpread Spectrum - Wideband radio frequency technique used for more reliable and secure data transmission.SSID (Service Set IDentifier) - Your wireless network's name.Static IP Address - A fixed address assigned to a computer or device that is connected to a network.Static Routing - Forwarding data in a network via a fixed path.Subnet Mask - An address code that determines the size of the network.Switch - 1. A data switch that connects computing devices to host computers, allowing a large number of devices to share a limited number of ports. 2. A device for making, breaking, or changing the connections in an electrical circuit. TCP (Transmission Control Protocol) - A network protocol for transmitting data that requires acknowledgement from the recipient of data sent.TCP/IP (Transmission Control Protocol/Internet Protocol) - A set of instructions PCs use to communicate over a network.Telnet - A user command and TCP/IP protocol used for accessing remote PCs.TFTP (Trivial File Transfer Protocol) - A version of the TCP/IP FTP protocol that has no directory or password capability.Throughput - The amount of data moved successfully from one node to another in a given time period.TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for each packet transmitted.Topology - The physical layout of a network.TX Rate - Transmission Rate.UDP (User Datagram Protocol) - A network protocol for transmitting data that does not require acknowledgement from the recipient of the data that is sent.Upgrade - To replace existing software or firmware with a newer version. Upload - To transmit a file over a network.URL (Uniform Resource Locator) - The address of a file located on the Internet.
72Appendix E: GlossaryWireless-G Access PointVPN (Virtual Private Network) - A security measure to protect data as it leaves one network and goes to another over the Internet.WAN (Wide Area Network)- The Internet.WEP (Wired Equivalent Privacy) - A method of encrypting network data transmitted on a wireless network for greater security.WINIPCFG - A Windows 98 and Me utility that displays the IP address for a particular networking device.WLAN (Wireless Local Area Network) - A group of computers and associated devices that communicate with each other wirelessly.WPA (Wi-Fi Protected Access) - a wireless security protocol using TKIP (Temporal Key Integrity Protocol) encryption, which can be used in conjunction with a RADIUS server.
73Appendix F: SpecificationsWireless-G Access PointAppendix F: SpecificationsModel WAP54GStandards IEEE 802.11g, IEEE 802.11b, IEEE 802.3, IEEE 802.3uPorts/Buttons One 10/100 Auto-Cross Over (MDI/MDI-X) port, power port, reset and SES buttonCabling Type RJ-45LEDs Power, Activity, Link, SecureEasySetupTransmit Power 802.11g: Typ. 13.5 +/- 2dBm @ Normal Temp Range802.11b: Typ: 16.5 +/- 2dBm @ Normal Temp RangeSecurity Features WPA, Linksys Wireless Guard, WEP Encryption, MAC Filtering, SSID Broadcast enable/disableWEP Key Bits 64/128-bitDimensions 7.32" x 1.89" x 6.65"(W x H x D) (186 mm x 48 mm x 169 mm)Unit Weight 16.23 oz. (0.46 kg)Power External, 12V DCCertifications FCCOperating Temp. 0ºC to 40ºC (32ºF to 150ºF)Storage Temp. 0ºC to 70ºC (-40ºF to 185ºF
74Appendix F: SpecificationsWireless-G Access PointOperating Humidity 10% to 85% Non-CondensingStorage Humidity 5% to 90% Non-CondensingLinksys declares that WAP54GP ( FCC ID: Q87-WAP54GV3 ) is limited in CH1~CH11 for 2.4 GHz by specified firmware controlled in U.S.A.
75Appendix G: Warranty InformationWireless-G Access PointAppendix G: Warranty InformationLIMITED WARRANTYLinksys warrants to You that, for a period of three years (the “Warranty Period”), your Linksys Product will be substantially free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys' entire liability under this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any rebates. This limited warranty extends only to the original purchaser. If the Product proves defective during the Warranty Period call Linksys Technical Support in order to obtain a Return Authorization Number, if applicable. BE SURE TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN CALLING. If You are requested to return the Product, mark the Return Authorization Number clearly on the outside of the package and include a copy of your original proof of purchase. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. You are responsible for shipping defective Products to Linksys. Linksys pays for UPS Ground shipping from Linksys back to You only. Customers located outside of the United States of America and Canada are responsible for all shipping and handling charges. ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to You. This warranty gives You specific legal rights, and You may also have other rights which vary by jurisdiction.This warranty does not apply if the Product (a) has been altered, except by Linksys, (b) has not been installed, operated, repaired, or maintained in accordance with instructions supplied by Linksys, or (c) has been subjected to abnormal physical or electrical stress, misuse, negligence, or accident. In addition, due to the continual development of new techniques for intruding upon and attacking networks, Linksys does not warrant that the Product will be free of vulnerability to intrusion or attack.TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT (INCLUDING ANY SOFTWARE), EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if any warranty or remedy provided under this Agreement fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You.Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623.
76Appendix H: Regulatory InformationWireless-G Access PointAppendix H: Regulatory InformationFCC StatementThis product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna• Increase the separation between the equipment or devices• Connect the equipment to an outlet other than the receiver's• Consult a dealer or an experienced radio/TV technician for assistanceFCC Radiation Exposure StatementIndustry Canada (Canada)This device complies with Canadian ICES-003 and RSS210 rules.Cet appareil est conforme aux normes NMB-003 et RSS210 d'Industry Canada.Operation is subject to the following two conditions:1) This device may not cause interference and2) This device must accept any interference, including interference that may cause undesired operation of the device.This device has been designed to operate with an antenna having a maximum gain of 2 dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
77Appendix I: Contact InformationWireless-G Access PointAppendix I: Contact InformationNeed to contact Linksys?Visit us online for information on the latest products and updates to your existing products at: http://www.linksys.com or ftp.linksys.comCan't find information about a product you want to buyon the web? Do you want to know more about networkingwith Linksys products? Give our advice line a call at: 800-546-5797 (LINKSYS)Or fax your request in to: 949-823-3002If you experience problems with any Linksys product,you can call us at: 800-326-7114Don't wish to call? You can e-mail us at: support@linksys.comIf any Linksys product proves defective during its warranty period,you can call the Linksys Return Merchandise Authorizationdepartment for obtaining a Return Authorization Number at: 949-823-3000(Details on Warranty and RMA issues can be found in the WarrantyInformation section in this Guide.)

Navigation menu