LINKSYS LAPAC1750 AC1750 Dual Band Access Point User Manual

LINKSYS LLC AC1750 Dual Band Access Point

User Manual.pdf

LAPAC1750 AC1750 Dual Band Access Point User's Guide
i TABLE OF CONTENTS CHAPTER 1 QUICK START GUIDE ................................................................................... 1Package Contents .............................................................................................................. 1Physical Details .................................................................................................................. 1Mounting Guide ................................................................................................................. 3CHAPTER 2 ACCESS POINT SETUP .................................................................................. 4Overview ............................................................................................................................ 4Setup using a Web Browser .............................................................................................. 4Setup Wizard ..................................................................................................................... 6User Accounts .................................................................................................................... 9Time Screen ..................................................................................................................... 10Log Settings Screen ......................................................................................................... 11Management Access Screen ............................................................................................ 13SSL Certificate Screen .................................................................................................... 15Network Setup Screen ..................................................................................................... 16Advanced Screen ............................................................................................................. 18Wireless Screens .............................................................................................................. 20Basic Settings ................................................................................................................... 20Security Settings .............................................................................................................. 22Rogue AP Detection ........................................................................................................ 32Scheduler .......................................................................................................................... 34Scheduler Association ..................................................................................................... 36Connection Control ......................................................................................................... 37Rate Limit ........................................................................................................................ 38QoS ................................................................................................................................... 39Workgroup Bridge .......................................................................................................... 41Advanced Settings ........................................................................................................... 43CHAPTER 3 OPERATION AND STATUS ......................................................................... 46Operation ......................................................................................................................... 46System Summary ............................................................................................................. 46LAN Status ....................................................................................................................... 48Wireless Status ................................................................................................................. 50Wireless Clients ............................................................................................................... 52Statistics ........................................................................................................................... 53Log View........................................................................................................................... 54CHAPTER 4 ACCESS POINT MANAGEMENT ............................................................... 55Overview .......................................................................................................................... 55Firmware Upgrade .......................................................................................................... 55Configuration ................................................................................................................... 57Factory Default ................................................................................................................ 59Reboot ............................................................................................................................... 60Ping Test ........................................................................................................................... 61Packet Capture ................................................................................................................ 62Diagnostic Log ................................................................................................................. 63APPENDIX A TROUBLESHOOTING ................................................................................ 64Overview .......................................................................................................................... 64General Problems ............................................................................................................ 64APPENDIX B ABOUT WIRELESS LANS .......................................................................... 66Overview .......................................................................................................................... 66Wireless LAN Terminology ............................................................................................ 66
ii APPENDIX C PC AND SERVER CONFIGURATION .................................................... 69Overview .......................................................................................................................... 69Using WEP ....................................................................................................................... 69Using WPA2-PSK ............................................................................................................ 70Using WPA2-Enterprise ................................................................................................. 71802.1x Server Setup (Windows 2000 Server) ................................................................ 72802.1x Client Setup on Windows XP ............................................................................. 82Using 802.1x Mode (without WPA) ............................................................................... 88 REGULATORY APPROVALS ............................................................................................. 93Federal Communication Commission Interference Statement ................................... 93Radiation Exposure Statement....................................................................................... 93 Industry Canada statement ............................................................................................ 93Caution ............................................................................................................................. 94Avertissement .................................................................................................................. 94 Radiation Exposure Statement....................................................................................... 94Déclaration d'exposition aux radiations ........................................................................ 94 Copyright © 2014. All Rights Reserved. Document Version: 1.0 All trademarks and trade names are the properties of their respective owners.
1 Chapter 1 Quick Start Guide Package Contents • Linksys Wireless Access Point • Quick Start Guide • Ethernet Cable • AC Power Adapter • CD with Documentation • Mounting Bracket • Mounting Kit • Ceiling Mount Back Plate • Drilling Layout Template Physical Details There is one LED for the device. LED LED Color Activity Status Green Blinking System is booting. Solid System is normal; no wireless device connected. Blue Blinking Software upgrade in process. Solid System is normal; at least one wireless device connected. Solid Booting process or update failed; hard reset or service re-quired. Port and Button Power Port - Connect the AC power adapter to this port. NOTE: Use only the adapter that came with your access point. Ethernet Port - Connect a wired network device to this port. This port supports PoE (Power over Ethernet) with a PoE switch or PoE injector. LAPAC1750 can be powered on from an 802.3at compliance source. NOTE: When both PoE and AC power adapter are connected to access point, device will get power from PoE as higher precedence. Using Cat5e or better cable is high recommended. 1
2 Reset Button - Press and hold this button for less than 15 seconds to power cycle device. Press and hold for longer than 15 seconds to reset the device to factory default settings.
3 Mounting Guide To avoid overheating, do not install your access point if ambient temperatures exceed 104°F (40°C). Install on a flat, stable surface, near the center of your wireless coverage area making sure not to block vents on the sides of the device enclosure. Wall Installation 1. Position drilling layout template at the desired location. 2. Drill four screw holes on the mounting surface. If your Ethernet cable is routed be-hind the wall, mark Ethernet cable hole as well. 3. Secure the mounting bracket on the wall with anchors and screws. 4. If your Ethernet cable is routed behind the wall, cut or drill the Ethernet cable hole you marked in Step 2. Feed the Ethernet cable through the hole. 5. Connect the Ethernet cable and/or AC power adapter to your device. 6. Slide the device into the bracket. Turn clockwise until it locks into place. Ceiling Installation 1. Select ceiling tile for mounting and remove tile. 2. Position drilling layout template at the desired location. 3. Drill four screw holes and Ethernet cable hole on the surface of ceiling tile.. 4. Place back plate on the opposite side of ceiling tile. Secure mounting bracket to the ceiling tile with flathead screw and nut. Route the Ethernet cable through the Ethernet cable hole. 5. Replace tile in ceiling. 6. Connect the Ethernet cable and/or AC power adapter to your device 7. Slide the device into the bracket. Turn access point clockwise until it locks. IMPORTANT Improper or insecure mounting could result in damage to the device or personal injury. Linksys is not responsible for damages caused by improper mounting.
4 Chapter 2 Access Point Setup Overview This chapter describes the setup procedure to connect the wireless access point to your LAN, and configure it as an access point for your wireless stations. Wireless stations may also require configuration. For details, see Appendix C - Wireless Station Configuration. The wireless access point can be configured using a Web browser. Setup using a Web Browser Your browser must support JavaScript. The configuration program has been tested on the following browsers: • Firefox 3.5 or later, Chrome 8 or later, Safari 5 or later • Internet Explorer 7 or later Setup Procedure Before starting setup, install the wireless access point on your LAN, as described earlier. 1. Locate the wireless access point’s default name on a label on the base or rear. The default name will be lapxxxxx where xxxxx is a set of the last 5 characters of your access point MAC Address. MAC Address is available in the brown box label or product label. 2. Use a PC connected to your LAN, either by a wired connection or another access point. Until the wireless access point is configured, establishing a wireless connection to it may be not possible. If your LAN contains a router or routers, ensure the PC used for configuration is on the same LAN segment as the wireless access point. 3. Start your Web browser. 4. Enter the IP address of the wireless access point, as in this example, which uses the wireless access point's default IP address: http://192.168.1.252 At the login prompt, enter admin for the User name, and admin for the Password. These are the default values. You should change the password. 2
5 Figure 1: Password Dialog 5. From the status screen menu configure for your environment. Details of these screens and settings are described in the following sections of this chapter. 6. You may also wish to change the admin password on the User Accounts screen, accessed from the Configuration menu. 7. Wireless stations must now be set to match the wireless access point. See Chapter 4 for details. If you can't connect: It is likely that your PC’s IP address is incompatible with the wireless access point’s IP address. This can happen if your LAN does not have a DHCP Server. The default IP address of the wireless access point is 192.168.1.252, with a network mask of 255.255.255.0. If your PC’s IP address is not compatible with this, you must change your PC’s IP address to an unused value in the range 192.168.1.1 ~ 192.168.1.254, with a network mask of 255.255.255.0. See Appendix A - Windows TCP/IP for details for this procedure.
6 Setup Wizard The first time you connect to the wireless access point, run the Setup Wizard to configure the device. 1. Click the Quick Start link on the main menu Figure 2: Setup Wizard 2. On the first screen, click Launch. 3. Set the password on the Device Password screen, if desired. 4. Configure the time zone, date and time for the device on System Settings screen. Figure 3: Setup Wizard - System Settings 5. On the IPv4 Address screen (Figure 6) configure the IP address of the device then click Next. If you want to configure more than 4 SSIDs, please go to Configuration->Wireless ->Basic Settings. The access point supports up to 8 SSIDs per radio.
7 Figure 4: Setup Wizard - IPv4 6. Set the SSID information on the Wireless Network screen. Click Next. Figure 5: Setup Wizard - Wireless Network 7. On the Wireless Security Screen (Figure 8) configure the wireless security settings for the device. Click Next. If you are looking for security options that are not available in the wi-zard, go to Configuration Æ WirelessÆ Security page. The access point supports more sophisticated security options there. Figure 6: Setup Wizard - Wireless Security
8 8. On the Summary screen, check the data to make sure they are correct and then click Submit to save the changes. Figure 7: Setup Wizard - Summary 9. Click Finish to leave the wizard. Figure 8: Setup Wizard - Finish
9 User Accounts Click User Accounts on the Administration menu to manage user accounts. The access point supports up to 5 users: one administrator and four normal users. Figure 9: User Accounts Data - User Accounts Screen User Account Table User Name Enter the User Name to connect to the access point’s admin interface. User Name is effective once you save settings. User Name can include up to 63 characters. Special characters are allowed. User Level Only administrator account has Read/Write permission to the access point’s admin interface. All other accounts have Read Only permis-sion. New Password Enter the Password to connect to the access point’s admin interface. Password must be between 4 and 63 characters. Special characters are allowed. Confirm New Password Re-enter password.
10 Time Screen Click Time on the Administration menu to configure system time of the device. Figure 10: Time Screen Data - Time Screen Time Current Time Display current date and time of the system. Manually Set date and time manually. Automatically When enabled (default setting) the access point will get the current time from a public time server. Time Zone Choose the time zone for your location from the drop-down list. If your location observes daylight saving time, enable “Automatically adjust clock for daylight saving changes.” Start Time Specify the start time of daylight saving. End Time Specify the end time of daylight saving. Offset Select the adjusted time of daylight saving. NTP NTP Server 1 Enter the primary NTP server. It can be an IPv4 address or a domain name. Valid characters include alphanumeric characters, "_", "-" and ".". Maximum length is 64 characters. NTP Server 2 Enter the secondary NTP server. It can be an IPv4 address or a domain name. Valid characters include alphanumeric characters, "_", "-" and ".". Maximum length is 64 characters.
11 Log Settings Screen The logs record various types of activity on the access point. This data is useful for trouble-shooting, but enabling all logs will generate a large amount of data and adversely affect performance. Figure 11: Log Settings Screen Data - Logs Screen Log Types Log Types Select events to log. Checking all options increase the size of the log, so enable only events you believe are required. Email Alert Email Alert Enable email alert function. SMTP Server Enter the e-mail server that is used to send logs. It can be an IPv4 address or a domain name. Valid characters include alphanumeric characters, "_", "-" and ".". Maximum length is 64 characters. Data Encryption Enable if you want to use data encryption. Port Enter the port for the SMTP server. The port is a value from 1 to 65535 and default is 25. Username Enter the Username to login to your SMTP server. The Username can include up to 32 characters. Special characters are allowed. Password Enter the Password to login to your SMTP server. The Password can include up to 32 characters. Special characters are allowed.
12 Email Address for Logs Enter the email address the log messages are to be sent to. Valid characters include alphanumeric characters, "_", "-", "." and "@". Maximum length is 64 characters. Log Queue Length Enter the length of the queue: up to 500 log messages. The default is 20 messages. When messages reach the set length the queue will be sent to the specified email address. Log Time Threshold Enter the time threshold (in seconds) used to check if the queue is full. It’s a value from 1 to 600 and default is 600 seconds. Syslog Syslog Notification Enable Syslog notification. IP Type Select the IP type of the syslog server: IPv4 or IPv6. Server IP Address Enter the IPv4 or IPv6 address of syslog server here.
13 Management Access Screen You can use the Management page to configure the management methods of the access point. Figure 12: Management Access Screen Data - Management Access Screen Web Access HTTP HTTP (Hyper Text Transfer Protocol) is the standard for transferring files (text, graphic images and other multimedia files) on the World Wide Web. Enable to allow Web access by HTTP protocol. HTTP Port Specify the port for HTTP. It can be 80 (default) or from 1024 to 65535. HTTP to HTTPS Redirect Enable to redirect Web access of HTTP to HTTPS automatically. This field is available only when HTTP access is disabled. HTTPS HTTPS (Hypertext Transfer Protocol Secure) can provide more secure communication with the SSL/TLS protocol, which support data encryption to HTTP clients and servers. Enable to allow Web access by HTTPS protocol. HTTPS Port Specify the port for HTTPS. It can be 443 (default) or from 1024 to 65535. From Wireless Enable wireless devices to connect to access point’s admin page. Disabled by default. Access Control By default, no IP addresses are prohibited from accessing the device’s admin page. You can enable access control and enter specified IP addresses for access. Four IPv4 and four IPv6 ad-dresses can be specified.
14 SNMP Settings SNMP Simple Network Management Protocol (SNMP) is a network monitoring and management protocol. Enable or disable SNMP function here. Disabled by default. Contact Enter contact information for the access point. The contact includes 1 to 32 characters. Special characters are allowed. Location Enter the area or location where the access point resides. The location includes 1 to 32 characters. Special characters are allowed. SNMP v1/v2 Settings Get Community Enter the name of Get Community. Get Community is used to read data from the access point and not for writing data into the access point. Get Community includes 1 to 32 characters. Special characters are allowed. Set Community Enter the name of Set Community. Set Community is used to write data into the access point. The Set Community includes 1 to 32 characters. Special charac-ters are allowed. SNMP v3 Settings SNMP v3 Settings Configure the SNMPv3 settings if you want to use SNMPv3. • Username: Enter the username. It includes 0 to 32 charac-ters. Special characters are allowed. • Authentication Protocol: None or HMAC-MD5. • Authentication Key: 8 to 32 characters. Special characters are allowed. • Privacy Protocol: None or CBC-DES. • Privacy Key: 8 to 32 characters. Special characters are allowed. Access Control Access Control When SNMP is enabled, any IP address can connect to the access point’s admin page through SNMP. You can enable access control to allow specified IP addresses. Two IPv4 and two IPv6 addresses can be specified. SNMP Trap Trap Community Enter the Trap Community server. It includes 1 to 32 characters. Special characters are allowed. Trap Destination Two Trap Community servers are supported: can be IPv4 or IPv6.
15 SSL Certificate Screen This screen can be used to manage SSL certificate used by HTTPS. Figure 13: SSL Certificate Screen Data - SSL Certificate Screen Export/Restore to/from Local PC Export SSL Certificate Click to export the SSL certificate. Install Certificate Browse to choose the certificate file. Click Install Certificate button. Export to TFTP Server Destination File Enter the name of the destination file. TFTP Server Enter the IP address for the TFTP server. Only support IPv4 address here. Export Click to export the SSL certificate to the TFTP server. Restore from TFTP Server Source File Enter the name of the source file. TFTP Server Enter the IP address for the TFTP server. Only support IPv4 address here. Install Click to install the file to the device.
16 Network Setup Screen Use this screen to configure basic device settings, VLAN settings and settings for the LAN interface, including static or dynamic IPv4/IPv6 address assignment. Figure 14: Network Setup Screen Data - Network Setup Screen TCP/IP Host Name Assign a host name to this access point. Host name consists of 1 to 15 characters. Valid characters include A-Z, a-z, 0-9 and -. Character cannot be first and last character of hostname and hostname cannot be composed of all digits. VLAN Enables or disables VLAN function. Untagged VLAN Enables or disables VLAN tagging. If enabled (default), traffic from the LAN port is untagged when the following conditions are met: 1) VLAN ID is equal to Untagged VLAN ID and 2) untagged traffic can be accepted by LAN port. If disabled, traffic from the LAN port is always tagged and only tagged traffic can be accepted from LAN port. By default all traffic on the access point uses VLAN 1, the default untagged VLAN. All traffic will be untagged until you disable the untagged VLAN, change the untagged traffic VLAN ID, or change the VLAN ID for a SSID. Untagged VLAN ID Specifies a number between 1 and 4094 for the untagged VLAN ID. The default is 1. Traffic on the VLAN that you specify in this field is not be tagged with a VLAN ID when forwarded to the network. Untagged VLAN ID field is active only when untagged VLAN is enabled. VLAN 1 is the default for both untagged VLAN and management VLAN.
17 Management VLAN The VLAN associated with the IP address you use to connect to the access point. Provide a number between 1 and 4094 for the Manage-ment VLAN ID. The default is 1. IPv4/v6 IP Settings Select Automatic Configuration or Static IP Address. IP Address Enter an unused IP address from the address range used on your LAN. Subnet Mask Enter the subnet mask for the IP address above. Default Gateway Enter the gateway for the IP address above. Primary DNS Enter the DNS address. Secondary DNS Optional. If entered, this DNS will be used if the Primary DNS does not respond.
18 Advanced Screen Use this screen to configure advanced network settings of the access point. Figure 15: Advanced Screen Data - Advanced Screen Port Settings Auto Negotiation If enabled, Port Speed and Duplex Mode will become grey and cannot be configured. If disabled, Port Speed and Duplex Mode can be configured. Operational Auto Negotiation Current Auto Negotiation mode of the Ethernet port. Port Speed Select the speed of the Ethernet port. Available only when Auto Negotiation is disabled. The option can be 10M, 100M or 1000M (default). Operational Port Speed Displays the current port speed of the Ethernet port. Duplex Mode Select the duplex mode of the Ethernet port. Available only when Auto Negotiation is disabled. The option can be Half or Full (default). Operational Duplex Mode Displays the current duplex mode of the Ethernet port. Flow Control Enable or disable flow control of the Ethernet port. 802.1x Supplicant 802.1x Supplicant Enable if your network requires this access point to use 802.1X authentication in order to operate.
19 Authentication This feature supports following two kinds of authentication: • Authentication via MAC Address Select this if you want to use MAC Address for authentica-tion. The access point uses lowercase MAC address for Name and Password, like xxxxxxxxxxxx. • Authentication via Name and Password Select this if you want to use name and password for authentication. Name - Enter the login name. The name includes 1 to 63 characters. Special characters are allowed. Password - Enter the desired login password. The password includes 4 to 63 characters. Special characters are allowed. Discovery Settings Bonjour Enable if administrator wants the access point to be discovered by Bonjour enabled devices automatically. If VLAN is enabled, the discovery packets will be sent out via management VLAN only. The access point supports http and https services. LLDP Enable if administrator wants the access point to be discovered by switch by LLDP protocol. Information such as product name, device name, firmware version, IP address, MAC address and so on will be advertised. LLDP-MED Enable if administrator wants the access point to be discovered by switch by LLDP-MED protocol. Information such as product name, device name, firmware version, IP address, MAC address and so on will be advertised.
20 Wireless Screens There are ten configuration screens: • Basic Settings • Security • Rogue AP Detection • Scheduler • Scheduler Association • Connection Control • Rate Limit • QoS • Workgroup Bridge • Advanced Settings Basic Settings Basic Settings provides the essential configuration for your wireless radio and SSIDs. You should able to set up your wireless network with these essential parameters configured. For advanced wireless settings such as Band Steering, Channel Bandwidth etc., they will be on Configuration ÆWirelessÆ Advanced Settings screen. Click Basic Settings on the Wireless menu. Figure 16: Basic Settings Screen Data - Wireless Basic Settings Screen Basic Wireless Settings Wireless Radio Select the wireless radio from the list. Radio 1 is for 2.4 GHz, and Radio 2 is for 5 GHz.
21 Enable Radio Enable or disable the wireless radio. Wireless Mode Select the desired option for radio 1: • G only - allow connection by 802.11G wireless stations only. • N only - allow connection by 802.11N wireless stations only. • B/G-Mixed - allow connection by 802.11B and G wireless stations only. • B/G/N-Mixed (Default) - allow connections by 802.11N, 802.11B and 802.11G wireless stations. Select the desired option for radio 2: • N/A-Mixed - allow connection by 802.11A and N wireless stations only. • N only - allow connection by 802.11N wireless stations only. • AC only - allow connection by 802.11AC wireless stations only. • A/N/AC-Mixed - allow connection by 802.11A, 802.11N and 802.11AC wireless stations. Wireless Channel Select wireless channel of the radio. If Auto is selected, the access point will select the best available channel when device boots up. If you experience lost connections and/or slow data transfers, experiment with manually setting different channels to see which is the best. SSID Settings SSID Name Enter the desired SSID Name. Each SSID must have a unique name. The name includes 1 to 32 characters Broadcast Enable or disable the broadcast of the SSID. When the access point does not broadcast its SSID, the network name is not shown in the list of available networks on a client station. In-stead, you must enter the exact network name manually into the wireless connection utility on the client so that it can connect. Isolation Enable or disable isolation among clients of the SSID. If enabled, wireless clients cannot communicate with others in the same SSID. It’s disabled by default. VLAN ID Enter the VLAN ID of the SSID. Used to tag packets which are received from the wireless clients of the SSID and sent from Ethernet or Workgroup Bridge interfaces. Applicable only when VLAN function is enabled. VLAN function can be configured in Configuration -> LAN -> Network Setup screen. Max Clients Enter the number of clients that can connect to the SSID. The range is from 0 to 32, and 0 means no limit.
22 Security Settings Use this screen to configure security settings of SSIDs to provide data protection over the wireless network Figure 17: Security Settings Data - SSID Settings Screen Security Select SSID Select the desired SSID from the drop-down list. Security Mode Select the desired security method from the list. Security Settings • Disabled - No security. Anyone using the correct SSID can connect to your network. • WEP - The 802.11b standard. Data is encrypted before transmission, but the encryption system is not very strong. • WPA2-Personal - This is a further development of WPA-PSK, and offers even greater security, using the AES (Advanced Encryption Standard) method. This method, some-times called "Mixed Mode", allows clients to use either WPA-Personal (with TKIP) or WPA2-Personal (with AES). • WPA2-Enterprise - Requires a RADIUS Server on your LAN to provide the client authentication according to the 802.1x standard. Data transmissions are encrypted using the WPA2 standard. If this option is selected: • This access point must have a client login on the RADIUS Server. • Each user must authenticate on the RADIUS Server. This is usually done using digital certificates.
23 • Each user's wireless client must support 802.1x and provide the RADIUS authentica-tion data when required. • All data transmission is encrypted using the WPA2 standard. Keys are automatically generated, so no key input is required. • RADIUS - RADIUS mode utilizes RADIUS server for authentication and dynamic WEP key generation for data encryption.
24 Security Settings - WEP This is the 802.11b standard. Data is encrypted before transmission, but the encryption system is not very strong. Figure 18: WEP Wireless Security Screen Data - WEP Screen WEP Authentication Select Open System or Shared Key. All wireless stations must use the same method. Default Transmit Key Select a transmit key. WEP Encryption Select an encryption option, and ensure your wireless stations have the same setting: • 64-Bit Encryption - Keys are 10 Hex characters. • 128-Bit Encryption - Keys are 26 Hex characters. Passphrase Generate a key or keys, instead of entering them directly. Enter a word or group of printable characters in the Passphrase box and click the Generate button to automatically configure the WEP key. It consists of 1 to 30 characters. Key Value Enter a key in hexadecimal format.
25 Security Settings - WPA2-Personal This is a further development of WPA-Personal, and offers even greater security. Figure 19: WPA2-Personal Wireless Security Screen Data - WPA2-Personal Screen WPA2-Personal WPA Algorithm The encryption method is AES. Wireless stations must also use AES. Pre-shared Key Enter the key value. It is 8 to 63 ASCII characters or 64 HEX characters. Other wireless stations must use the same key. Key Renewal Specify the value of Group Key Renewal. It’s a value from 600 to 36000 and default is 3600. WPA automatically changes secret keys after a certain period of time. The group key interval is the period of time in between automatic changes of the group key, which all devices on the network share. Constantly keying the group key protects your network against intrusion, as the would-be intruder must cope with an ever-changing secret key.
26 Security Settings - WPA/WPA2-Personal This method, sometimes called Mixed Mode, allows clients to use either WPA-Personal or WPA2-Personal. Figure 20: WPA/WPA2-Personal Wireless Security Screen Data - WPA/WPA2-Personal Screen WPA/WPA2-Personal WPA Algorithm The encryption method is TKIP or AES. Pre-shared Key Enter the key value. It is 8 to 63 ASCII characters or 64 HEX characters. Other wireless stations must use the same key. Key Renewal Specify the value of Group Key Renewal. It’s a value from 600 to 36000, and default is 3600. WPA automatically changes secret keys after a certain period of time. The group key interval is the period of time in between automatic changes of the group key, which all devices on the network share. Constantly keying the group key protects your network against intrusion, as the would-be intruder must cope with an ever-changing secret key.
27 Security Settings - WPA2-Enterprise This version of WPA2-Enterprise requires a RADIUS Server on your LAN to provide the client authentication. Data transmissions are encrypted using the WPA2 standard. Figure 21: WPA2-Enterprise Wireless Security Screen Data - WPA2-Enterprise Screen WPA2-Enterprise Primary Server Enter the IP address of the RADIUS Server on your network. Primary Server Port Enter the port number used for connections to the RADIUS Server. It is a value from 1 to 65534, and default is 1812. Primary Shared Secret Enter the key value to match the RADIUS Server. It consists of 1 to 64 characters. Backup Server The Backup Authentication Server will be used when the Primary Authentication Server is not available. Backup Server Port Enter the port number used for connections to the Backup RADIUS Server. It’s a value from 1 to 65534, and default is 1812. Backup Shared Secret Enter the key value to match the Backup RADIUS Server. It consists of 1 to 64 characters. WPA Algorithm The encryption method is AES.
28 Key Renewal Timeout Specify the value of Group Key Renewal. It is a value from 600 to 36000, and default is 3600. WPA automatically changes secret keys after a certain period of time. The group key interval is the period of time in between automatic changes of the group key, which all devices on the network share. Constantly keying the group key protects your network against intrusion, as the would-be intruder must cope with an ever-changing secret key.
29 Security Settings - WPA/WPA2-Enterprise WPA/WPA2-Enterprise requires a RADIUS Server on your LAN to provide the client authen-tication. Data transmissions are encrypted using WPA2 standard. Figure 22: WPA/WPA2-Enterprise Wireless Security Screen Data - WPA/WPA2-Enterprise Screen WPA/WPA2-Enterprise Primary Server Enter the IP address of the RADIUS Server on your network. Primary Server Port Enter the port number used for connections to the RADIUS Server. It is a value from 1 to 65534, and default is 1812. Primary Shared Secret Enter the key value to match the RADIUS Server. It consists of 1 to 64 characters. Backup Server The Backup Authentication Server will be used when the Primary Authentication Server is not available. Backup Server Port Enter the port number used for connections to the Backup RADIUS Server. It is a value from 1 to 65534, and default is 1812. Backup Shared Secret Enter the key value to match the Backup RADIUS Server. It consists of 1 to 64 characters. WPA Algorithm The encryption method is TKIP or AES.
30 Key Renewal Timeout Specify the value of Group Key Renewal. It is a value from 600 to 36000, and default is 3600. WPA automatically changes secret keys after a certain period of time. The group key interval is the period of time between automatic changes of the group key, which all devices on the network share. Constantly keying the group key protects your network against intrusion, as the would-be intruder must cope with an ever-changing secret key.
31 RADIUS Use RADIUS server for authentication and dynamic WEP key generation for data encryption. Figure 23: RADIUS Settings Data - RADIUS Screen Authentication Server Primary Server Enter the IP address of the RADIUS Server on your network. Primary Server Port Enter the port number used for connections to the RADIUS Server. It is a value from 1 to 65534, and default is 1812. Primary Shared Secret Enter the key value to match the RADIUS Server. It consists of 1 to 64 characters. Backup Server The Backup Authentication Server will be used when the Primary Authentication Server is not available. Backup Server Port Enter the port number used for connections to the Backup RADIUS Server. It is a value from 1 to 65534, and default is 1812. Backup Shared Secret Enter the key value to match the Backup RADIUS Server. It consists of 1 to 64 characters.
32 Rogue AP Detection Rogue AP detection is used to detect the unexpected or unauthorized access point installed in a secure network environment. Figure 24: Rogue AP Screen Data - Rogue AP Screen Wireless Radio Select the desired radio from the list. Radio 1 is for 2.4 GHz, and Radio 2 is for 5 GHz. Rogue AP Enable or disable Rogue AP Detection on the selected radio. Detected Rogue AP List Action Click Trust to move the AP to the Trusted AP List. MAC Address The MAC address of the Rogue AP. SSID The SSID of the Rogue AP. Channel The channel of the Rogue AP. Security The security method of the Rogue AP. Signal The signal level of the Rogue AP. Trusted AP List Action Click Untrust to move the AP to the Rogue AP List. MAC Address The MAC address of the Trusted AP. SSID The SSID of the Trusted AP. Channel The channel of the Trusted AP. Security The security method of the Trusted AP. Signal The signal level of the Trusted AP.
33 New MAC Address Add one trusted AP by MAC address.
34 Scheduler Configure a rule with a specific time interval for SSIDs to be operational. Automate enabling or disabling SSIDs based on the profile definition. Support up to 16 profiles and each profile can include 4 time rules. Figure 25: Scheduler Screen Data - Scheduler Screen Wireless Scheduler Enable or disable wireless scheduler on the radio. It is disabled by default. If disabled, even if some SSIDs are associated with profiles, they will be always active. Scheduler Operational Status Status The operational status of the scheduler. Reason The detailed reason for the scheduler operational status. It includes following situations. • System time is outdated. Scheduler is inactive because system time is outdated. • Administrative Mode is disabled. Scheduler is disabled by administrator. • Active Scheduler is active. Scheduler Profile configuration New Profile Name Enter the name for new profile. Profile Name Select the desired profile from the list to configure.
35 Day of the Week Select the desired day from the list. Option None means this time rule is disabled. Start Time Choose the start time. Finish Time Choose the finish time.
36 Scheduler Association Associate defined scheduler profiles with SSIDs. Figure 26: Scheduler Association Screen Data - Scheduler Association Screen Wireless Radio Select the desired radio from the list. Radio 1 is for 2.4 GHz, and Radio 2 is for 5 GHz. Scheduler Association SSID The index of SSID. SSID Name The name of the SSID. Profile Name Choose the profile that is associated with the SSID. If the profile associated with the SSID is deleted, then the associa-tion will be removed. If "None" is selected, it means no scheduler profile is associated. Interface Status The Status of the SSID. It can be Enabled or Disabled. Scheduler only works when the SSID is enabled.
37 Connection Control Exclude or allow only listed client stations to authenticate with the access point. Figure 27: Connection Control Screen Data - Connection Control Screen SSID Select the desired SSID from the list. Connection Type Select the option from the drop-down list as desired. • Local: Choose either Allow only following MAC addresses to connect to wireless network or Prevent following MAC addresses from connection to wireless network. You can enter up to 20 MAC addresses of wireless stations or choose the MAC address. • RADIUS • Primary/Backup RADIUS Server - Enter the IP address of the RADIUS Server. • Primary/Backup RADIUS Server Port – Enter the Port number of the RADIUS Server. • Primary/Backup Shared Secret - This is shared between the wireless access point and the RADIUS Server while authenticating the device attempting to connect. • Disabled
38 Rate Limit Limit downstream and upstream rate of SSIDs. Figure 28: Rate Limit Screen Data - Rate Limit Screen Wireless Radio Select the desired radio from the list. Radio 1 is for 2.4 GHz, and Radio 2 is for 5 GHz. Rate Limit SSID The index of SSID. SSID Name The name of the SSID. Upstream Rate Enter a maximum upstream for the SSID. The range is from 0 to 300 Mbps for Radio 1 and from 0 to 800 Mbps for Radio 2; 0 means no limitation. Downstream Rate Enter a maximum downstream for the SSID. The range is from 0 to 300 Mbps for Radio 1 and from 0 to 800 Mbps for Radio 2; 0 means no limitation.
39 QoS The QoS (Quality of Service) feature allows you to specify priorities for different traffic coming from your wireless client. Lower priority traffic will be slowed down to allow greater throughput or less delay for high priority traffic. Figure 29: QoS Screen Data - QoS Screen QoS Setting Wireless Radio Select the desired radio from the list. Radio 1 is for 2.4 GHz, and Radio 2 is for 5 GHz. QoS Settings SSID The index of SSID. SSID Name The name of the SSID. VLAN ID The VLAN ID of the SSID. Priority Select the priority level from the list. The 802.1p will be included in the VLAN header of the packets which are received from the SSID and sent from Ethernet or Workgroup Bridge interface.
40 WMM Enable or disable WMM. WMM (Wi-Fi Multimedia) is a component of the IEEE 802.11e wireless LAN standard for QoS. WMM provides prioritization of wireless data packets from different applications based on four access categories: voice, video, best effort, and background. For an application to receive the benefits of WMM QoS, both it and the client running that application have to have WMM enabled. Legacy applications that do not support WMM and applica-tions that do not require QoS, are assigned to the best effort category, which receives a lower priority than voice and video. WMM is enabled by default.
41 Workgroup Bridge Workgroup Bridge feature enables the access point to extend the accessibility of a remote network. In Workgroup Bridge mode, the access point acts as a wireless station (STA) on the wireless LAN. It can bridge traffic between a remote wired network and a wireless LAN. When Workgroup Bridge is enabled, SSID configuration still works to provide wireless services to clients. All access points participating in Workgroup Bridge must have the identical settings for Radio interface, IEEE 802.11 mode, Channel Bandwidth, Channel (Auto is not recommended). Figure 30: Workgroup Bridge Data - Workgroup Bridge Screen Workgroup Bridge Radio Select the desired radio from the list. Workgroup Bridge Status Status Enable or disable Workgroup Bridge function. Before configuring Workgroup Bridge, make sure all devices in Workgroup Bridge have the following identical settings. • Radio • IEEE 802.11 Mode • Channel Bandwidth • Channel (Auto is not recommended) Infrastructure Client Interface SSID Enter the name of the SSID to which Workgroup Bridge will connect. Click Site Survey button to choose from the list. It's necessary for Workgroup Bridge to connect to remote access point.
42 Remote MAC Address Normally, Workgroup Bridge connects to a remote access point by matching SSID. When more than one remote access point have the same SSID, Workgroup Bridge can connect to different remote access points. Optional: You can specify the MAC address of the remote access point to limit Workgroup Bridge’s connection to a specific remote access point. The format is xx:xx:xx:xx:xx:xx. VLAN ID Enter the VLAN ID for Workgroup Bridge. When VLAN function is enabled, Workgroup Bridge only forwards packets with specified VLAN to remote access points. The list is only applicable when VLAN function is enabled. Security Mode Select the desired mode from the list. • Disabled • WPA-Personal • WPA2-Personal
43 Advanced Settings Configure advanced parameters of wireless radios. Figure 31: Advanced Settings Data - Advanced Settings Screen Band Steering Band Steering Enable or disable Band Steering function. Band Steering is a technology that detects whether the wireless client is dual-band capable. If it is, band steering pushes the client to connect to the less-congested 5 GHz network. It does this by actively blocking the client’s attempts to connect with the 2.4GHz network. Isolation Isolation between SSIDs Define whether to isolate traffic between SSIDs. If enabled, wireless clients in different SSIDs cannot communicate with each other. Enabled by default. Advanced Parameters Wireless Radio Select the desired radio from the list. Radio 1 is for 2.4 GHz, and Radio 2 is for 5 GHz. Worldwide Mode (802.11d) Worldwide Mode (802.11d) enables the access point to direct connected wireless devices to radio settings specific to where in the world the devices are in use.
44 Channel Bandwidth Select the designed channel bandwidth for the wireless radio. • 20MHz - Select if you are not using any 802.11n wire-less clients. • 20/40MHz - Select if you are using both 802.11n and non-802.11n wireless devices. • 20/40/80MHz - Select if you are using 802.11ac, 802.11n and non-802.11n wireless devices. Guard Interval Select the guard interval manually for Wireless-N connections. The two options are Short (400 nanoseconds) and Long (800 nanoseconds). The default is Auto. CTS Protection Mode CTS (Clear-To-Send) Protection Mode boosts the access point's ability to catch all Wireless-G transmissions, but it severely decreases performance. By default, CTS Protection Mode is disabled, but the access point will automatically enable this feature when Wireless-G devices are not able to transmit to the access point in an environment with heavy 802.11b traffic. Beacon Interval The access point transmits beacon frames at regular intervals to announce the existence of the wireless network. Enter the interval between the transmissions of beacon frames. The value range is between 40 and 1000 milliseconds and default is 100 milliseconds. DTIM Interval Enter the Delivery Traffic Information Map (DTIM) period, an integer from 1 to 255 beacons. The default is 1 beacon. The DTIM message is an element included in some beacon frames. It indicates which client stations, currently sleeping in low-power mode, have data buffered on the access point await-ing pickup. The DTIM period that you specify indicates how often the clients served by this WAP device should check for buffered data still on the access point awaiting pickup. For example, if you enter 1, clients check for buffered data on the access point at every beacon. If you enter 10, clients check on every 10th beacon.
45 RTS Threshold Enter the Request to Send (RTS) Threshold value, an integer from 1 to 2347. The default is 2347 octets. The RTS threshold indicates the number of octets in a Medium Access Control Protocol Data Unit (MPDU) below which an RTS/CTS handshake is not performed. Changing the RTS threshold can help control traffic flow through the access point, especially one with a lot of clients. If you specify a low threshold value, RTS packets are sent more frequently, which consumes more bandwidth and reduces the throughput of the packet. However, sending more RTS packets can help the network recover from interference or collisions that might occur on a busy network, or on a network experiencing electromagnetic interference. Fragmentation Threshold Enter the fragmentation threshold, an integer from 256 to 2346. The default is 2346. The fragmentation threshold is a way of limiting the size of packets (frames) transmitted over the network. If a packet exceeds the fragmentation threshold you set, the fragmentation function is activated and the packet is sent as multiple 802.11 frames. If the packet being transmitted is equal to or less than the threshold, fragmentation is not used. Setting the threshold to the largest value (2,346 bytes, which is the default) effectively disables fragmentation. Fragmentation involves more overhead because of the extra work of dividing up and reassembling of frames it requires, and because it increases message traffic on the network. However, fragmentation can help improve network performance and reliability if properly configured. Output Power Select the output power of the access point. If many access points exist, lower power can reduce the signal interference among them.
46 Chapter 3 Operation and Status Operation You may need to perform the following operations on a regular basis. • If using the Access Control feature, update the Trusted PC database as required. (See Access Control in Chapter 2 for details.) • If using 802.1x mode, update the User Login data on the Windows 2000 Server, and configure the client PCs, as required. System Summary Provide system status of the access point. Figure 32: System Summary Screen 3
47 Data - System Summary Screen System Summary Device SKU The SKU is often used to identify device model number and region. Firmware Version The version of the firmware currently installed. Firmware Checksum The checksum of the firmware running in the access point. Hardware Version The version of the hardware. Local MAC Address The MAC (physical) address of the wireless access point. Serial Number The serial number of the device. Host Name The host name assigned to the access point. System Up Time How long the system has been running since the last restart or reboot. System Time The current date and time. Power Source The power source of the access point. It can be Power over Ethernet (PoE) or Power Adapter. When two power sources are plugged in, Power Adaptor will be displayed. Buttons Refresh Click to update the data on the screen.
48 LAN Status LAN Status displays settings, and status of LAN interface. Figure 33: LAN Status Screen Data - LAN Status VLAN VLAN Enabled or disabled (default). Untagged VLAN Enabled (default) or disabled. When enabled, and if its VLAN ID is equal to Untagged VLAN ID, all traffic is untagged when sent from LAN ports. Untagged traffic can be accepted by LAN ports. If disabled, traffic is always tagged when sent from LAN port and only tagged traffic can be accept from LAN port. By default all traffic on the access point uses VLAN 1, the default untagged VLAN. This means that all traffic is untagged until you disable the untagged VLAN, change the untagged traffic VLAN ID, or change the VLAN ID for a SSID. Untagged VLAN ID Displays the untagged VLAN ID. Traffic on the VLAN that you specify in this field is not be tagged with a VLAN ID when for-warded to the network. VLAN 1 is the default ID for untagged VLAN and management VLAN.
49 Management VLAN Displays the Management VLAN ID. The VLAN associated with the IP address you use to connect to the access point. Provide a number between 1 and 4094 for the Management VLAN ID. The default is 1. This VLAN is also the default untagged VLAN. If you already have a management VLAN configured on your network with a different VLAN ID, you must change the VLAN ID of the man-agement VLAN on the access point. IPv4/v6 IP Address The IP address of the wireless access point. Subnet Mask The Network Mask (Subnet Mask) for the IP address above. Default Gateway Enter the gateway for the LAN segment to which the wireless access point is attached (the same value as the PCs on that LAN segment). Primary DNS The primary DNS address provided by the DHCP server or configured manually. Secondary DNS The secondary DNS address provided by the DHCP server or configured manually.
50 Wireless Status Wireless Status displays settings and status of wireless radios and SSIDs. Figure 34: Wireless Status Screen Data - Wireless Status Radio Status Wireless Radio Select the desired radio from the list. Radio 1 is for 2.4 GHz, and Radio 2 is for 5 GHz. Radio Status Indicates whether the radio is enabled. Mode Current 802.11mode (a/b/g/n) of the radio. Channel The channel currently in use. Channel Bandwidth Current channel bandwidth of the radio. When set to 20 MHz, only the 20 MHz channel is in use. When set to 40 MHz, Wireless-N connections will use 40 MHz channel, but Wireless-B and Wireless-G will still use 20 MHz channel. SSID Status Interface SSID index. SSID Name Name of the SSID. Status Status of the SSID, enabled or disabled. MAC Address MAC Address of the SSID. VLAN ID VLAN ID of the SSID. Priority The 802.1p priority of the SSID.
51 Scheduler State Current scheduler status of the SSID. • N/A No scheduler is enabled on the SSID, or the SSID is disabled by administrator. • Active The SSID is enabled. • Inactive The SSID is disabled. Workgroup Bridge Status Status Status of the Workgroup Bridge: enabled or disabled. Local MAC MAC address of the Workgroup Bridge. Remote SSID SSID of the destination access point on the other end of the Workgroup Bridge link to which data is sent and from which data is received. Remote MAC MAC address of the destination access point on the other end of the Workgroup Bridge link to which data is sent and from which data is received. Connection Status Status of the Workgroup Bridge: disabled, connected or not con-nected.
52 Wireless Clients Wireless Clients displays connected clients based on each wireless interface. Figure 35: Wireless Clients Screen Data - Wireless Clients Wireless Interface Select the desired interface from the list. The interfaces include 8 SSIDs per radio. SSID Name Name of the SSID to which the client connects. Client MAC The MAC address of the client. SSID MAC MAC of the SSID to which the client connects. Link Rate The link rate of the client. Unit is Mbps. RSSI The signal strength of the client. Unit is dBm. Online Time How long this client has been online. Unit is seconds.
53 Statistics Statistics provides real-time transmitted and received statistics data based on each SSID per Radio, and LAN interface. Figure 36: Statistics Screen Data - Statistics Wireless Radio Select the desired radio from the list. Radio 1 is for 2.4 GHz, and Radio 2 is for 5 GHz. Transmit/Receive • Total Packets - The total packets sent (in Transmit table) or re-ceived (in Received table) by the interface. • Total Bytes - The total bytes sent (in Transmit table) or received (in Received table) by the interface. • Total Dropped Packets - The total number of dropped packets sent (in Transmit table) or received (in Received table) by the interface. • Total Dropped Bytes - The total number of dropped bytes sent (in Transmit table) or received (in Received table) by the interface. • Errors - The total number of errors related to sending and receiving data on this interface.
54 Log View Log View shows a list of system events that are generated by each single log entry, such as login attempts and configuration changes. Figure 37: Log View Screen Data - Log View Log Messages Log Messages Show the log messages. Buttons Refresh Update the data on screen. Save Save the log to a file on your PC. Clear Delete the existing logs from device.
55 Chapter 4 Access point Management Overview This chapter covers features available on the wireless access point’s Maintenance menu. • Maintenance • Firmware Upgrade • Configuration Backup/Restore • Factory Default • Reboot • Diagnostics • Ping Test • Packet Capture • Diagnostic Log Firmware Upgrade The firmware (software) in the wireless access point can be upgraded by using HTTP/HTTPS, or TFTP. Check Linksys support website (http://www.linksys.com/business/support) and download the latest firmware release to your storage such as PC. Then, perform firmware upgrade by following the steps below. During firmware upgrade, do not power off device or disconnect Ethernet cable. Device will reboot automatically after firmware upgrade is completed. 4
56 Figure 38: Firmware Upgrade Screen To perform the firmware upgrade from local PC: 1. Click the Browse button and navigate to the location of the upgrade file. 2. Select the upgrade file. Its name will appear in the Upgrade File field. 3. Click the Upgrade button to commence the firmware upgrade. To perform the firmware upgrade from TFTP server: 1. Enter the IP address of the TFTP server and the source file. The source file is the firmware filename you stored in your TFTP server. Only support IPv4 address here. 2. Click the Upgrade button to commence the firmware upgrade. To perform the firmware upgrade from Internet: 1. Click Check for Upgrade to button to check if new firmware is available. Click the Upgrade button to commence the firmware download and upgrade if new firmware is available.
57 Configuration Configuration backup/restore allows you to download the configuration file from device to external storage, e.g., your PC, or network storage, or to upload a previously saved configura-tion file from external storage to device. It is highly recommended you save one extra copy of the configuration file to external storage after you are done with access point setup. Figure 39: Configuration Backup/Restore Screen Data - Configuration Backup/Restore Screen Backup/Restore to/from Local PC Backup Configuration Once you have the access point working properly, you should back up the settings to a file on your computer. You can later restore the access point's settings from this file, if necessary. To create a backup file of the current settings: • Click Backup. • If you don't have your browser set up to save downloaded files automatically, locate where you want to save the file, rename it if you like, and click Save. Restore Configuration To restore settings from a backup file: 1. Click Browse. 2. Locate and select the previously saved backup file. 3. Click Restore
58 Backup/Restore to/from TFTP server Backup Configuration To create a backup file of the current settings: 1. Enter the destination file name you plan to save in TFTP server. 2. Enter the IP address for the TFTP server. Only support IPv4 address here. 3. Click Backup Restore Configuration To restore settings from a backup file: 1. Enter the source file name stored in TFTP server. 2. Enter the IP address for the TFTP server. Only support IPv4 address here. 3. Click Restore
59 Factory Default It’s highly recommended you save your current configuration file before you restore to factory default settings. To save your current configuration file, click Maintenance Æ Configuration Backup/Restore. Figure 40: Factory Default Screen Data - Factory Default Screen Factory Default If Yes radio button is clicked and Save button is pressed, your current configuration file will be deleted, and the system will reboot. The access point will go back to factory default mode after reboot.
60 Reboot Reboot power cycles the device. The current configuration file will remain after reboot. Figure 41: Reboot Screen Data - Reboot Screen Device Reboot If Yes radio button is checked, device will power cycle after Save button is pressed.
61 Ping Test Ping Test is used to determine the accessibility of a host on the network. Figure 42: Ping Test Screen Data - Ping Test Screen General IP Type Enter the IP type of destination address. IP or URL Address Enter the IP address or domain name that you want to ping. Packet Size Enter the size of the packet. Times to Ping Select the desired number from the drop-list. • 5 • 10 • 15 • Unlimited
62 Packet Capture Packet Capture is used to capture and store 802.3 packets received and transmitted by the access point based on one specified network interface. Network interface can be radio, SSID or LAN. Figure 43: Packet Size Screen Data - Packet Size Screen Network Interface Select the desired network interface from the drop-down list. The interface can be Radio, SSID or Ethernet. Start Capture Click it to start the capture. You will be asked to specify a local file to store the packets. Stop Capture Click it to stop the capture.
63 Diagnostic Log Diagnostic Log provides system detail information, such as configuration file, system status and statistics data, hardware information, operational status. The information is useful in troubleshooting and working with technical support. Figure 44: Diagnostic Screen Data - Diagnostic Screen Download Click to download the device diagnostic log into a local file.
64 Appendix A Troubleshooting Overview This chapter covers some common problems encountered while using the wireless access point, and some possible solutions to them. If you follow the suggested steps and the wireless access point still does not function properly, contact your dealer for further advice. General Problems Problem 1: I can't find new access point on my network. Solution 1: Check the following. • The wireless access point is properly installed, LAN connections are OK, and it is powered ON. Check the LEDs for system and port status. • Ensure that your PC and the wireless access point are on the same network segment. (If you don't have a router, this must be the case.) • You can use the following method to determine the IP address of the wireless access point, and then try to connect using the IP address, in-stead of the name. To Find the access point's IP Address 1. Open a MS-DOS Prompt or Command Prompt Window. 2. Use the Ping command to ping the wireless access point. Enter ping followed by the default name of the wireless access point. Default name is a string with “lap” and the last 5 characters of device MAC address. e.g. ping lap964d6 3. Check the output of the ping command to determine the IP address of the wireless access point, as shown below. Figure 45: Ping If your PC uses a Fixed (Static) IP address, ensure that it is using an IP Address that is in the network segment (subnet) with the wireless access point. On Windows PCs, you can use Control Panel->Network to check the Properties for the TCP/IP protocol. A
65 If there is no DHCP Server found, the wireless access point will roll back to an IP address and mask of 192.168.1.252 and 255.255.255.0. Problem 2: My PC can't connect to the LAN via the wireless access point. Solution 2: Check the following: • The SSID and security settings on the PC match the settings on the wireless access point. • On the PC, the wireless mode is set to "Infrastructure" • If using the Access Control feature, the PC's name and address is in the Trusted Stations list. • If using 802.1x mode, ensure the PC's 802.1x software is configured correctly. See Chapter 4 for details of setup for the Windows XP 802.1x client. If using a different client, refer to the vendor's docu-mentation.
66 Appendix B About Wireless LANs Overview Wireless networks have their own terms and jargon. It is necessary to understand many of these terms in order to configure and operate a wireless LAN. Wireless LAN Terminology Modes Wireless LANs can work in either of two (2) modes: • Ad-hoc • Infrastructure Ad-hoc Mode Ad-hoc mode does not require an access point or a wired (Ethernet) LAN. Wireless stations, e.g., notebook PCs with wireless cards communicate directly with each other. Infrastructure Mode In Infrastructure Mode, one or more access points are used to connect wireless stations, e.g., notebook PCs with wireless cards to a wired (Ethernet) LAN. The wireless stations can then access all LAN resources. Access points can only function in "Infrastructure" mode, and can communicate only with wireless stations that are set to "Infrastructure" mode. SSID/ESSID BSS/SSID A group of wireless stations and a single access point, all using the same ID (SSID), form a Basic Service Set (BSS). Using the same SSID is essential. Devices with different SSIDs are unable to communi-cate with each other. ESS/ESSID A group of wireless stations, and multiple access points, all using the same ID (ESSID), form an Extended Service Set (ESS). Different access points within an ESS can use different channels. To reduce interference, it is recommended that adjacent access points SHOULD use different channels. B
67 As wireless stations are physically moved through the area covered by an ESS, they will automatically change to the access point that has the least interference or best performance. This capability is called Roaming. (Access points do not have or require roaming capabili-ties.) Channels The wireless channel sets the radio frequency used for communication. • Access points use a fixed channel. You can select the channel used. This allows you to choose a channel that provides the least interference and best performance. For USA and Canada, the following channels are available. 2.4GHz: 2.412 to 2.462 GHz; 11 channels 5GHz: • 5.180 to 5.240 GHz; 4 channels • 5.745 to 5.825 GHz; 5 channels • If using multiple access points it is better if adjacent access points use different channels to reduce interference. The recommended channel spacing between adjacent access points is five channels, e.g., use Channels 1 and 6, or 6 and 11. • In "Infrastructure" mode wireless stations normally scan all channels looking for an access point. If more than one access point can be used, the one with the strongest signal is used. (This can only happen within an ESS.) • If using "Ad-hoc" mode (no access point) all wireless stations should be set to use the same channel. However, most wireless stations will still scan all channels to see if there is an existing "Ad-hoc" group they can join. WEP WEP (Wired Equivalent Privacy) is a standard for encrypting data before it is transmitted. This is desirable because it is impossible to prevent snoopers from receiving any data which is transmitted by your wireless stations. If the data is encrypted, it is meaningless unless the receiver can decrypt it. If WEP is used, the wireless stations and the wireless access point must have the same settings. WPA-PSK In WPA-PSK, like WEP, data is encrypted before transmission. WPA is more secure than WEP. The PSK (Pre-shared Key) must be entered on each wireless station. The 256-bit encryption key is derived from the PSK, and changes frequently. WPA2-PSK This is a further development of WPA-PSK, and offers even greater security, using the AES (Advanced Encryption Standard) method of encryption. It should be used if possible.
68 WPA-Enterprise This version of WPA requires a RADIUS server on your LAN to provide the client authentica-tion according to the 802.1X standard. Data transmissions are encrypted using the WPA standard. If this option is used: • The access point must have a "client login" on the RADIUS server. • Each user must have a "user login" on the RADIUS server. • Each user's wireless client must support 802.1X and provide the login data when required. All data transmission is encrypted using the WPA standard. Keys are automatically generated, so no key input is required. WPA2-Enterprise This version of WPA2 requires a RADIUS server on your LAN to provide the client authentication according to the 802.1X standard. Data transmissions are encrypted using the WPA2 standard. If this option is used: • The access point must have a "client login" on the RADIUS server. • Each user must have a "user login" on the RADIUS server. • Each user's wireless client must support 802.1X and provide the login data when required. All data transmission is encrypted using the WPA2 standard. Keys are automatically generated, so no key input is required. 802.1x This uses the 802.1X standard for client authentication, and WEP for data encryption. If possible, you should use WPA-Enterprise instead, because WPA encryption is much stronger than WEP encryption. If this option is used: • The access point must have a "client login" on the RADIUS server. • Each user must have a "user login" on the RADIUS server. • Each user's wireless client must support 802.1X and provide the login data when required. • All data transmission is encrypted using the WEP standard. You only have to select the WEP key size; the WEP key is automatically generated.
69 Appendix C PC and Server Configuration Overview All wireless stations need to have settings that match the wireless access point. These settings depend on the mode in which the access point is being used. • If using WEP or WPA2-PSK, it is only necessary to ensure that each wireless station's settings match those of the wireless access point, as described below. • For 802.1x modes, configuration is much more complex. The RADIUS server must be configured correctly, and setup of each wireless station is also more complex. Using WEP For each of the following items, each wireless station must have the same settings as the wireless access point. Mode On each PC, the mode must be set to Infrastructure. SSID (ESSID) This must match the value used on the wireless access point. The default value is LinksysSMB24G for radio 1 and LinksysSMB5G for radio 2. Note: The SSID is case sensitive. Wireless Security • Each wireless station must be set to use WEP data encryption. • The key size (64 bit, 128 bit) must be set to match the access point. • The key values on the PC must match the key values on the access point. Note: On some systems, the key sizes may be shown as 40-bit and 104-bit instead of 64-bit, 128-bit. This is because the key input by the user is 24 bits less than the key size used for encryption. C
70 Using WPA2-PSK For each of the following items, each wireless station must have the same settings as the wireless access point. Mode On each PC, the mode must be set to Infrastructure. SSID (ESSID) This must match the value used on the wireless access point. The default value is LinksysSMB24G for radio 1 and LinksysSMB5G for radio 2. Note The SSID is case sensitive. Wireless Security On each client, wireless security must be set to WPA2-PSK. • The Pre-shared Key entered on the access point must also be entered on each wireless client. • The Encryption method (e.g. TKIP, AES) must be set to match the access point.
71 Using WPA2-Enterprise This is the most secure and most complex system. WPA-Enterprise mode provides greater security and centralized management, but it is more complex to configure. Wireless Station Configuration For each of the following items, each wireless station must have the same settings as the wireless access point. Mode On each PC, the mode must be set to Infrastructure. SSID (ESSID) This must match the value used on the wireless access point. The default value is LinksysSMB24G for radio 1 and LinksysSMB5G for radio 2. Note The SSID is case sensitive. 802.1x Authentication Each client must obtain a certificate for authentication for the RADIUS server. 802.1x Encryption Typically, EAP-TLS is used. This is a dynamic key system, so keys do NOT have to be entered on each wireless station. You can also use a static WEP key (EAP-MD5). The wireless access point supports both methods simultaneously. RADIUS Server Configuration If using WPA2-Enterprise mode, the RADIUS server on your network must be configured as follows. • It must provide and accept Certificates for user authentication. • There must be a Client Login for the wireless access point itself. The wireless access point will use its default name as its client login name. (However, your RADIUS server may ignore this and use the IP address instead.) The Shared Key, set on the Security Screen of the access point, must match the Shared Secret value on the RADIUS server. • Encryption settings must be correct.
72 802.1x Server Setup (Windows 2000 Server) This section describes using Microsoft Internet Authentication Server as the RADIUS server, since it is the most common RADIUS server available that supports the EAP-TLS authentica-tion method. The following services on the Windows 2000 Domain Controller (PDC) are also required. • dhcpd • dns • rras • webserver (IIS) • RADIUS Server (Internet Authentication Service) • Certificate Authority Windows 2000 Domain Controller Setup 1. Run dcpromo.exe from the command prompt. 2. Follow all of the default prompts, ensure that DNS is installed and enabled during installa-tion. Services Installation 1. Select the Control Panel -> Add/Remove Programs. 2. Click Add/Remove Windows Components from the left side. 3. Ensure that the following components are selected. Certificate Services. After enabling this, you will see a warning that the computer cannot be renamed and joined after installing certificate services. Select Yes to select certificate services and continue World Wide Web Server. Select World Wide Web Server on the Internet Information Services (IIS) component. From the Networking Services category, select Dynamic Host Configuration Protocol (DHCP), and Internet Authentication Service (DNS should already be selected and installed).
73 Figure 46: Components Screen 4. Click Next. 5. Select the Enterprise root CA, and click Next. Figure 47: Certification Screen 6. Enter the information for the Certificate Authority, and click Next.
74 Figure 48: CA Screen 7. Click Next if you don't want to change the CA's configuration data. 8. Installation will warn you that Internet Information Services are running, and must be stopped before continuing. Click OK, then Finish. DHCP server configuration 1. Click on Start -> Programs -> Administrative Tools -> DHCP 2. Right-click on the server entry, and select New Scope. Figure 49: DHCP Screen 3. Click Next when the New Scope Wizard Begins. 4. Enter the name and description for the scope, click Next. 5. Define the IP address range. Change the subnet mask if necessary. Click Next.
75 Figure 50: IP Address Screen 6. Add exclusions in the address fields if required. If no exclusions are required, leave it blank. Click Next. 7. Change the Lease Duration time if preferred. Click Next. 8. Select Yes, I want to configure these options now, and click Next. 9. Enter the router address for the current subnet. The router address may be left blank if there is no router. Click Next. 10. For the parent domain, enter the domain you specified for the domain controller setup, and enter the server's address for the IP address. Click Next. Figure 51: DNS Screen 11. If you don't want a WINS server, just click Next. 12. Select Yes, I want to activate this scope now. Click Next, then Finish. 13. Right-click on the server, and select Authorize. It may take a few minutes to complete.
76 Certificate Authority Setup 1. Select Start -> Programs -> Administrative Tools -> Certification Authority. 2. Right-click Policy Settings, and select New -> Certificate to Issue. Figure 52: Certificate Authority Screen 3. Select Authenticated Session and Smartcard Logon (select more than one by holding down the Ctrl key). Click OK. Figure 53: Template Screen 4. Select Start -> Programs -> Administrative Tools -> Active Directory Users and Comput-ers. 5. Right-click on your active directory domain, and select Properties.
77 Figure 54: Active Directory Screen 6. Select the Group Policy tab, choose Default Domain Policy then click Edit. Figure 55: Group Policy Tab 7. Select Computer Configuration -> Windows Settings -> Security Settings -> Public Key Policies, right-click Automatic Certificate Request Settings -> New -> Automatic Certifi-cate Request.
78 Figure 56: Group Policy Screen 8. When the Certificate Request Wizard appears, click Next. 9. Select Computer, click Next. Figure 57: Certificate Template Screen 10. Ensure that your Certificate Authority is checked, click Next. 11. Review the policy change information and click Finish. 12. Click Start -> Run, type cmd and press enter. Enter secedit /refreshpolicy machine_policy This command may take a few minutes to take effect.
79 Internet Authentication Service (RADIUS) Setup 1. Select Start -> Programs -> Administrative Tools -> Internet Authentication Service 2. Right-click on Clients, and select New Client. Figure 58: Service Screen 3. Enter a name for the access point, click Next. 4. Enter the address or name of the wireless access point, and set the shared secret, as entered on the Security Settings of the wireless access point. 5. Click Finish. 6. Right-click on Remote Access Policies, select New Remote Access Policy. 7. Assuming you are using EAP-TLS, name the policy eap-tls, and click Next. 8. Click Add... If you don't want to set any restrictions and a condition is required, select Day-And-Time-Restrictions, and click Add... Figure 59: Attribute Screen 9. Click Permitted, then OK. Select Next. 10. Select Grant remote access permission. Click Next.
80 11. Click Edit Profile... and select the Authentication tab. Enable Extensible Authentication Protocol, and select Smart Card or other Certificate. Deselect other authentication me-thods listed. Click OK. Figure 60: Authentication Screen 12. Select No if you don't want to view the help for EAP. Click Finish.
81 Remote Access Login for Users 1. Select Start -> Programs -> Administrative Tools -> Active Directory Users and Comput-ers. 2. Double click on the user who you want to enable. 3. Select the Dial-in tab, and enable Allow access. Click OK. Figure 61: Dial-in Screen
82 802.1x Client Setup on Windows XP Windows XP ships with a complete 802.1x client implementation. If using Windows 2000, you can install SP3 (Service Pack 3) to gain the same functionality. If you don't have either of these systems, you must use the 802.1x client software provided with your wireless adapter. Refer to your vendor's documentation for setup instructions. The following instructions assume that: • You are using Windows XP • You are connecting to a Windows 2000 server for authentication. • You already have a login (User-name and password) on the Windows 2000 server. Client Certificate Setup 1. Connect to a network that doesn't require port authentication. 2. Start your Web browser. In the Address box, enter the IP address of the Windows 2000 Server, followed by /certsrv e.g http://192.168.0.2/certsrv 3. You will be prompted for a user name and password. Enter the User name and Password assigned to you by your network administrator, and click OK. Figure 62: Connect Screen 4. On the first screen (below), select Request a certificate, click Next.
83 Figure 63: Wireless CA Screen 5. Select User certificate request and select User Certificate, click Next. Figure 64: Request Type Screen 6. Click Submit.
84 Figure 65: Identifying Information Screen 7. A message will be displayed and the certificate will be returned to you. Click Install this certificate. Figure 66: Certificate Issued Screen 8. You will receive a confirmation message. Click Yes.
85 Figure 67: Root Certificate Screen 9. Certificate setup is now complete. 802.1x Authentication Setup 1. Open the properties for the wireless connection, by selecting Start - Control Panel - Network Connections. 2. Right-click on the Wireless Network Connection, and select Properties. 3. Select the Authentication Tab, and ensure that Enable network access control using IEEE 802.1X is selected, and Smart Card or other Certificate is selected from the EAP type. Figure 68: Authentication Tab Encryption Settings The encryption settings must match the access point’s on the wireless network you wish to join. • Windows XP will detect any available wireless networks, and allow you to configure each network independently.
86 • Your network administrator can advise you of the correct settings for each network. 802.1x networks typically use EAP-TLS. This is a dynamic key system, so there is no need to enter key values. Enabling Encryption To enable encryption for a wireless network, follow this procedure. 1. Click on the Wireless Networks tab. Figure 69: Wireless Networks Screen 2. Select the wireless network from the Available Networks list, and click Configure. 3. Select and enter the correct values, as advised by your Network Administrator. For example, to use EAP-TLS, you would enable Data encryption, and click the checkbox for the setting The key is provided for me automatically, as shown below.
87 Figure 70: Properties Screen Setup for Windows XP and 802.1x client is now complete.
88 Using 802.1x Mode (without WPA) This is very similar to using WPA-Enterprise. The only difference is that on your client, you must NOT enable the setting The key is pro-vided for me automatically. Instead, you must enter the WEP key manually, ensuring it matches the WEP key used on the access point. Figure 71: Properties Screen Note: On some systems, the 64-bit WEP key is shown as 40-bit and the 128-bit WEP key is shown as 104-bit. This difference arises because the key input by the user is 24 bits less than the key size used for encryption.
89 Regulatory Approvals Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 25cm between the radiator & your body. Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. Industry Canada statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésira-ble.
90 Caution (i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; (ii) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled envi-ronment. This equipment should be installed and operated with minimum distance 25cm between the radiator & your body. Déclaration d'exposition aux radiations Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 25 cm de distance entre la source de rayonnement et votre corps.

Navigation menu