Kustom Signals CCBAS 900MHz Spread Spectrum Transceiver User Manual Manual Rev1

Kustom Signals Inc 900MHz Spread Spectrum Transceiver Manual Rev1

User Manual

006-0799-00 Rev 1 1 Digital Wireless Audio DSS Operating Instructions The Digital Wireless Audio DSS system is a digital frequency-agile radio designed to achieve excellent audio recording for the various Eyewitness Video systems. Transceiver Setup The Digital Wireless Audio DSS transceiver can be worn on a duty belt using the supplied pouch, or without the pouch, it can be worn/attached to an epaulet using the integrated clip. The epaulet clip remains on the transceiver even if the pouch is used – it will fit easily within the pouch. Base Station Setup The base station should be mounted according to the installation instructions (007-0798-00) found in the base station installation kit. You will need to attach the two antennas, then mount and connect the cable. For best reception, the antennas should be perpendicular to the ground. Operation Place the Transceiver (Mic) unit in the Base Unit (Base). This will “sync” the two devices. This sync will remain until the Mic is placed in a different Base or until a new Mic is placed in the Base. The last synchronization performed will override all earlier syncs. Under normal conditions, leaving the Mic in the Base will also charge the Mic, but there is no other need to place the Mic into the Base. After “syncing” is complete, the operation is very simple. The transceiver can be used with or without the supplied mic cord. There is an internal mic on the transceiver that will be used if you do not use the cord, or if the cord becomes damaged. For best results, we recommend you use the cord. When you plug it in, route the cord downward as shown, so the strap will hold the plug securely in place.
2 The Mic has a blue slide switch that is used to either 1) activate the audio system and start the video recording, or 2) to mute the audio while in the record mode. When audio is activated, you will feel a short “buzz” from the internal vibrator motor, and the LED’s will change to indicate the active mode (see LED legend below). To mute the audio, slide the switch again – this will result in two short buzzes from the internal vibrator. When you stop a Recording by pressing the Stop button on the Control Center, the Digital Wireless Audio will automatically return to the standby mode. REMOTE TRANSCEIVER LED INDICATORS LED 1 (closest to switch) LED 2 (middle) LED 3 (closest to logo) Vibrator Status OFF OFF OFF N/A Power Switch OFF RED GREEN BLUE N/A Pwr on, unit in Standby GREEN GREEN BLUE 1 Long System active, Audio recording RED GREEN BLUE 2 Short Standby or Muted RED RED BLUE N/A No Comm with Base Station OFF OFF BLUE N/A Battery Saver Mode** Normal State Normal State Slow Blink BLUE N/A Battery is low recharging required. Blink GREEN OFF OFF N/A Charging Battery GREEN OFF OFF N/A Charge Complete Flashing RED OFF OFF N/A Charge Fault ** Battery Saver Mode is entered when the Remote has lost communication with the Base for 10 or more minutes. This is to conserve battery life when an Officer is out of range for an extended amount of time. Pressing the slide switch will exit this mode or the remote will exit it automatically when the Base Station signal is received. BASE STATION LED INDICATORS LED 1 LED 2 LED 3 Status N/A N/A BLUE Power is supplied to Base unit RED GREEN BLUE Remote is in Standby or Mute GREEN GREEN BLUE Remote Active and Audio is being recorded N/A Red then Flash GREEN then Solid GREEN BLUE Remote is in Base Station and “Association” is Complete
3 Kustom Signals Inc. FCC ID: IVQCCRMT Model No. CCDSS-REM Tested To Comply with FCC Standards This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Kustom Signals Inc. FCC ID: IVQCCBAS Model No. CCDSS-BAS Tested To Comply with FCC Standards This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes not expressly approved by Kustom Signals voids the user's authority to operate the equipment. This product complies with FCC radiation exposure limits set forth for an uncontrolled environment.

Navigation menu