KYUNG JIN ELECTRON W-2400 Wireless Headset User Manual manual eng a

KYUNG JIN ELECTRON CO.,LTD Wireless Headset manual eng a

Users Manual

HeadsetTMUSER’S MANUALwirelessW-2400(V/R) Features Functions Installation Adjustment and Application Operation Precautions Troubleshooting Guide WarrantyWireless Telephone Headset2.4Ghz WIDE BAND CORDLESS HEADSETWIRELESS HEADSET FOR TELEPHONEHeadsetTMwi r ele s sW-2400KJ ambient temperature:-10℃ ℃ relative humidity:10%~95% atmospheric pressure:86~106Kpa 2.4Ghz wireless headset~+401.FeaturesConstitutionwireless telephone (main part)wireless headsetLIFTAdaptor applicable all telephone wireless connection distance:100M(max) calling time: 5h standby time:20hconnecting line LIFT Sponge cradlemanualLift connecting line2651Power Lift3478AFH MUTE
W-2400KJHeadsetTMwi r ele s s2.Functions A. B.C. Power Indicator Power Indicator (red) of Base Station will be ON when the Main Station is plugged into the electrical outlet.Call&Receive/Charge Indicator The indicator is ON when either the main station is being charged or the phone is being used.Volume adjustment of the microphone Adjust the volume of the microphone while the phone is D.E. F. G. H. I. J. being used.Select the telephone power line Select the telephone power line 1~ 4 range to match the different power.Polarity switch of MICPaging Buttonpaging button (headset signal)AdaptorHeadset connecting line (mic connecting line) jackTEL connecting line jack LIFT jackA. Receiver9V 30 0MAA C D E F G H I J B AFH MUTEHeadsetTMwi r ele s sW-2400KJB.Wireless HeadsetKLMNO.ON/OFF Battery Switch : make sure the power is ON when it is being used..Battery.MIC :(Microphone).Call / Receive : Press the Call/receive button when you either call or receive the phone..MUTE: The MUTE button on the Headset during a call to make other person not to hear your voice. To mute or un-mute during a call, press the MUTE button..indicator light.AFH: Select the optimal channel by changing the frequency..VOL: Volume adjustment for receiving .POWR OFFPQRSK L M N O P Q R S
W-2400KJHeadsetTMwi r ele s sC.LIFTTUVWXY. RING SENSOR: It can be varied due to using different type of phones (however the most of the phones will be same). LIFT INPUT: Connect to the LIFT with connecting line.. LIFT CTRL: The switch has 3 different positions to adjust the lifting level of the LIFT..RING LED: The light will be on when the LIFT is being used..RING LED: The light will be on when the.RING LED: The light will be on when theT U V WPower Lift3.InstallationHeadsetTMwi r ele s sW-2400KJPower OnLift OnXY
1. Plug Connect the DC9V adaptor on the backside of the main station.2. Unplug the handset (receiver) connection cable from the telephone and plug it in to the handset connecting jack at the bottom of W-2400 Main Station.(no need to connect with the phone without receiver)3. Connect with the provided connecting line to the unplugged jack of the handset(receiver) and the other end to jack at the bottom of the main station.4. Connect the LIFT with connecting line to the jack at the bottom of the main station and the jack of the LIFT.5. Use the Headset after it is fully charged. (The Battery ON/OFF switch must be ON when the headset is used).TEL LIFTLift inputW-2400KJHeadsetTMwi r ele s s9V 300M A1. Then the green light will be ON. Turn on the ON/OFF switch on the battery section to charge the headset. (It takes more than 6 hours to be fully charged when it is being charged the first time.)2. Make sure that the headset is properly placed on the main station. When it is properly done, the green light will be ON. Place the headset on top of the main station to charge. HeadsetTMwi r ele s sW-2400KJ4.Adjustment and ApplicationHeadset Charging1. Power switch should be ON after the headset has been separated from the main station when it is being used. (To save the battery, turn OFF the battery switch when it is not being used for a long time)2. Call/Receiving can be made by pressing the Call/Receiving switch. The LED light will be ON. Check the connection lines if either the LED light is not ON or no signal tone.3. MUTE button on the Headset may be used during a call to make other person not to hear your voice. To mute or un- mute during a call, press the MUTE button.4. Press the AFH button of the Adaptive Frequency Hopping System when several headsets are being used at the same location.Headset Application
W-2400KJHeadsetTMwi r ele s s1. Adjust A button to get the best sound.2. Change the B (1-4) switch on the headset when there is either no or abnormal signal tone.3. Use C button when the signal tone cannot be adjusted with A button.4. Use D button when you want to page the person using the headset.Main StationMIC1 2 3 4MIC1 2 3300M AABCDHeadsetTMwi r ele s sW-2400KJ5.OperationReceiving a Call1. Press the switch when the phone ringing.2. If the LIFT is connected, it will be operating automatically. If not, it can be answered by picking up the handset (receiver) of the phone or pressing the headset button.1. Press the switch then dial the number.2. Signal tone can be heard when the LIFT is operating. If the LIFT is not connected, the handset (receiver) should be picked up to hear the signal tone.Make a call
W-2400KJHeadsetTMwi r ele s s1. Keep the wireless headset dry. Precipitation, humidity and all types of liquids or moisture can contain minerals that it will corrode electronic circuits. If your device does get wet, allow it to dry completely. 2. Do not use or store the wireless headset in dusty, dirty areas. Its moving parts and electronic components can be damaged.3. Do not drop, knock, over powering when pressing buttons or shake the wireless headset. Rough handling can break internal circuit boards and fine mechanics.4. Do not attempt to open the wireless headset. If any part such as battery, adapter, headset and main station is not working properly, take it to the nearest authorized service facility for service.5. Battery life time is around 400 charging times. Make sure to make the replacement with properly certified battery with the same specifications.6. If the wireless headset will not be used for a long time, the switch for the battery should be OFF.7. If the Headset will not be used for a long time, it is recommended to charge fully then store in the original package and store it properly.6.PrecautionHeadsetTMwi r ele s sW-2400KJ7.Troubleshooting GuideLift is not functioning properly and indicator light is keeping flashingAll set up of the wireless headset is done properly but still not functioningCannot hear the other person’s voiceOther person cannot hear any soundPower supply is malfunctioning due to the connection is not properly madeFrequencies of Headset and Telephone is not matchedBattery is dead or its switch is offSound control of the Headset is not properly set upMIC volume control of the headset has not set up properlyThe jack of Automatic Lift Signal Cable to W-2400 Main Station should be removed and reconnectedPlace the Headset on the Main Station then operate while it is on the charge terminatorPut the switch ON or recharge the batteryAdjust the sound control on the HeadsetAdjust the MIC volume control on the main stationProblem Cause Solution
wirelessW-2400KJHeadsetTMwi r ele s s8.Warranty Service1. When the product is not working properly, do not attempt to repair it yourself and take it to the nearby certified service center or retail store where the product has purchased.Products cord and Number:Company name:Contact name:Email address:Address:Purchase date:Customer should fill out 1-5 and Retail store should fill out 6.This wireless headset does not guarantee the security during a call and may have some interference while in use.Warranty ServiceW-2400KJHeadsetTMH.K.OFFICE / KJ COMMUNICATION(H.K)CO., LTD.FACTORY / N-SIA COMMUNICATION(S.Z)CO., LTD.wirelessMAIN OFFICE / KYUNG JIN ELECTRON CO., LTD.www.kj-headset.co.kr2.4Ghz WIDE BAND CORDLESS HEADSETFCC Statement:This device complies with Part 15 of the FCC Rules. Operation is subject to the followingtwo conditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that maycauseundesired operation.Changes or modifications not expressly approved by the party responsible for compliancecould void the user's authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the followingmeasures:-- Reorient or relocate the receiving antenna.-- Increase the separation between the equipment and receiver.-- Connect the equipment into an outlet on a circuit different from that to which the receiveris connected.-- Consult the dealer or an experienced radio/TV technician for help.

Navigation menu