KINGTA TECHNOLOGY PB252B Bluetooth Speaker User Manual

KINGTA TECHNOLOGY CO., LTD Bluetooth Speaker

User manual

Begin Streaming Music Press ” ” to start playing musicPress and Hold ” ” 2 seconds to play the next trackPress and Hold ” ” 2 seconds to play previous trackPress either ” ” or ” ” for volume controlMaking and Receiving Phone CallsWhen the unit is connected and paired to your device,the unit allows you to make or receive phone calls with itsbuilt-in microphone.Press “ ” to accept a callTo end a call press ” ”To reject a call, press and hold ” ” for 2 secondsPlug in the supplied 3.5 mm cable into the unit. The other end isconnected to your device. the Blue LED will slow blink when in“Aux”mode.Please note music and volume can be controlled by your device.Attach the USB cable to the unit, and plug into any USB charger.If the unit is completely discharged, it will take approximately 3hours to fully charge.The Red LED will illuminate during charging, when it hascompleted, the Red LED will turn off.Note: There will be a beep when the battery is low and needs tobe recharged.Aux-In ModeCharging LED StatusBlue LED rapid blink & Blue LED solid Bluetooth ModeBlue LED slow blink Red LEDAux ModeChargingTroubleshootingUnit doesn’t connect to deviceSpeaker needs to be connected/re-paired to deviceA tone is heard every few seconds Speaker needs to be chargedUnit will not power on Speaker needs to be chargedUnit doesn’t controltrack(s)/volumeSpeaker needs to be in Bluetoothmode for full controlUnit distorts athigh volume The devices’ volume needs tobe lowered12 3456 PB252BBluetooth Speaker User’s ManualIntroduction:Description:Included:Specifications:Thank you for choosing the PB252B as your source for entertainment! you can use this item with iPads , iPhones,iPods and many types of smartphone to stream music ,and enjoy handsfree calling.In order to get the best results when using the device,please read this manual first before using.1.Speaker2.USB Micro Charging Cable3.3.5 mm Audio Cable4.User ManualSupported Profiles: A2DP, HFP, AVRCPBluetooth Range:33ft (10m)Dimensions: 185 mm x 25 mm x 82 mmBattery: Li-Ion 3.7V, 2000 mAhCharging: DC 5V @ 500 mAWeight: 320gOperation:Powering OnPress and Hold "ON/OFF" button 2 seconds to power ON, theBlue LED will start to rapid blink . If an Aux (3.5 mm) cable is connected to the unit, the Blue LEDwill slow blink, the unit is in Aux-In mode. Powering OffPaired mode:Press and Hold "ON/OFF" button 2 seconds to disconnect the Bluetooth, then Press and Hold "ON/OFF" button again to power off .Pairing/AUX mode:Press and Hold "ON/OFF" button 2 seconds to power offBluetooth ModePairingThe unit will automatically go into “Pairing Mode” when it ispowered ON.Go into your Bluetooth device settings menu and look for“PB252B”.After the unit has paired and connected, it will re-connectautomatically when the unit is powered on and the deviceis in range.Note: Bluetooth Timeout :10 minutes1.ON/OFF /Play/Pause/Phone button2.Previous/Volume –3.Next/Volume +4.Blue LED(Bluetooth) / Red LED(Charging)5.MIC6.Micro USB Charging Port / AUX in Port
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu