KING KWM1000 KWM1000 User Manual 23180 Rev B KING WiFiMax 07 17 18 indd

KING KWM1000 23180 Rev B KING WiFiMax 07 17 18 indd

user manual

Wi-Fi Extender KWM1000• KING WiFiMax• Power Supply• Antenna• Manual (this document)Attach 4th antenna.Rotate antennas into upright position.Connect to power.LET’S GET STARTED!1. Carefully open package and verify all contents are present.2. Set up and connect your KING WiFiMax as shown below.ABCAntennas must always point up.The KING WiFiMax creates your own private and secure Wi-Fi network, just like you have in your home. When in range of an available network, simply confi gure your WiFiMax to connect to that network, and it will extend the internet access from that network to your own private Wi-Fi network.
Page 21. Go to your phone, tablet or computer’s settings page and connect to the Wi-Fi Network: KING_XXXXXX_5G If your device cannot connect to KING_XXXXXX_5G, connect to KING_XXXXXX Graphics will vary.2. Open your device’s web browser. Go to: http://mykingwifi .comThis screen should appear. Tap “WiFi Settings” in the left-hand column. Back to SettingsWiFiKC1074ONKING_XXXXXX_5GKING_XXXXXXFun Lake CampgroundDad’s CampgroundChat CafeCampit HereChoose a Network...FIRST-TIME SETUPNOTE: If you have already completed fi rst-time setup, skip ahead to STANDARD OPERATION.WHICH NETWORK TO CHOOSE:KING_XXXXXX_5G is the 5GHz network and is faster than KING_XXXXXX which is the 2.4GHz network.Choose the 5GHz network when possible. NOTE: Some older devices may not have the ability to receive the 5GHz network, and therefore you may not see the 5GHz option.WiFi SettingsType exactly as written.
Page 33. This screen should appear. Tap “WiFi Name & Password.” 4. This screen should appear. Enter a custom Wi-Fi Name & Password for both your 2.4GHz and 5GHz networks. Tap “Save.” Congratulations! You have customized your router setup. Close the web page and go to STANDARD OPERATION on next page.TIP: Add “_5G” after your 5GHz network name to differentiate it from your 2.4GHz network name.TIP: KING highly recommends password protecting your name. Choose WPA/WPA2-PSK under “Encryption Mode” to enable password protection. (Passwords can be the same for both networks if you wish.)WPA/WPA2-PSKWPA/WPA2-PSKEnter password hereEnter password hereEnter name hereEnter name here_5GRECORD YOUR NAME AND PASSWORD HERE.2.4GHZ5GHZWrite your network name here: Write your password here:Write your network name here: Write your password here:
Page 41. Go to your phone, tablet or computer’s settings page and connect to the Wi-Fi Network with your customized network name. The example shown is “MyWiFiName_5G”. If your device cannot connect to your 5G network, connect to your other network. STANDARD OPERATIONBack to SettingsWiFiKC1075ONMyWiFiName_5GMyWiFiNameFun Lake CampgroundDad’s CampgroundChat CafeCampit HereChoose a Network...2. Open your device’s web browser. Go to: http://mykingwifi .comThis screen should appear. Tap “WiFi Settings” in the left-hand column. 2.4GHz: MyWiFiName5GHz: MyWiFiName_5GType exactly as written.WiFi Settings
Page 53. This screen should appear. Tap “WiFi Name & Password”. 4. This screen should appear. Tap the blue arrows to scan for networks. Select Your Network
Page 6 This screen should appear. The router is scanning for networks. 5. After the scanning process is complete, this screen should appear. Tap on the “Upstream WiFi Name” drop down menu to display a list of available networks. Camp-O-RamaDad’s CampgroundChat CafeCampit HereHot Spot InternetInternet City
Page 76. Select one of the listed networks and input the password if necessary (not pictured).Tap “Save.” 7. This popup should appear. Tap “OK.” 8. Your KING WiFiMax will reboot. Congratulations, your KING WiFiMax is now extending your network! NOTE: If your mobile device does not have internet access, you may need to go back to your settings App and ensure that you are connected to the router’s network as you will lose connection during the router’s rebooting process.
Page 8TROUBLESHOOTINGThe KING WiFiMax doesn’t power on (no blue lights on front). Make sure power supply plug is securely inserted into back of KING WiFiMax. Make sure the power supply is plugged into a known good power outlet. I can’t fi nd the network KING_XXXXXX_5G or KING_XXXXXX. Make sure your KING WiFiMax is plugged in. It may take up to a minute for these networks to appear. Some older devices may be unable to see the 5GHz network. This is completely okay; just use the KING_XXXXXX network.I can’t connect to mykingwifi .com Make sure you are connected to your KING WiFiMax’s network. Then make sure you type in the web address exactly as it appears in this manual: http://mykingwifi .com.I can’t enter a password in the designated box. Choose WPA/WPA2-PSK under “Encryption Mode” (right above the password box) to enable password protection. I don’t see the Upstream WiFi name I want to extend from my list of networks in step 4. If a network is very far away or very weak, the KING WiFiMax may not be able to see it, or may not offer it as an option. Try scanning again for networks by clicking on the blue circular arrows. If your network is still not offered as an option, try moving your KING WiFiMax to a location closer to your desired network.When my router reboots, it gets stuck at 100% and won’t fi nish rebooting. Try reloading the page. (If the page won’t load, make sure your device is still connected to the KING WiFiMax. It may have disconnected during the reboot.)The KING WiFiMax doesn’t seem to extend the range of my Wi-Fi, or has trouble picking up signal from my source. Make sure all 4 antennas are pointing up (if wall mounting, antennas must be rotated to point up as well.) Certain types of obstructions (other vehicles, buildings, or large amounts of metal) can reduce signal levels. Try relocating the KING WiFiMax.Let us help!KING Customer Service952-345-8147
Page 9Power: Included 12v power supply, requiring 110V AC plug-inWireless standards: IEEE802.11a/b/g/n/acSupported Frequencies: 2.4GHz and 5GHz (dual-band)Security: WPA/WPA2-PSKStorage Environment: Temperature -40ºF to 158ºFKING WIFIMAX SPECIFICATIONS
Page 10MANUFACTURER’S LIMITED WARRANTYEvery new KING WiFiMax is thoroughly inspected and tested before leaving the factory, and is covered by the following limited warranty from the date of original purchase: • One-year parts warranty: The customer is not responsible for the cost of replacement parts if the original part is determined to be defective under the terms of the warranty. The customer is responsible for the cost of replacement parts after one year.Only KING and certifi ed dealers may perform warranty evaluations and repairs. Depending upon the problem, KING may authorize a dealer to perform the necessary repairs. Any warranty labor outside of that performed at the factory is not covered unless 1) the product has been installed by an authorized dealer/installer or OEM manufacturer and 2) the dealer/installer receives prior authorization to perform the repair.A certifi ed dealer must not perform any repair without fi rst contacting KING for a Service Order Number. KING will advise the dealer on how to proceed with any repairs.Should any trouble develop during the warranty period, contact KING at (952) 922-6889. You must contact KING before the warranty period expires. The customer must supply proof of purchase (such as a dated sales receipt) when requesting warranty service. If the customer cannot supply proof of purchase, warranty period shall start 30 days after date of manufacture.If it is determined that the unit needs to be returned to KING, customer must return COMPLETE product, freight prepaid, to: KING, 11200 Hampshire Avenue South, Bloomington, MN 55438-2453.If inspection shows the trouble is caused by defective workmanship or material, KING will repair (or at its option, replace) without charge.When returning product, KING will supply an RMA number (Return Merchandise Authorization). This number must be clearly written on the box. Failure to clearly write RMA number on box will result in delays in processing claim. Along with product, the customer should include in the box: his/her name, address, daytime phone number, proof of purchase and description of the problem.This warranty does not cover installation and external wiring, or remanufactured units. This warranty does not cover damage caused by the use of an accessory other than a KING accessory designed for the product. This warranty is not transferable from the original owner.Due to the expanding and changing TV market, KING cannot be held responsible for changes made to satellite services. Software updates to address such issues are not covered under warranty.This warranty also does not apply where: • The product has been abused, misused, improperly installed or improperly maintained. • The product has been used with an accessory other than a KING accessory designed for the product. • Repairs have been made or attempted by others that are not certifi ed by KING to do such repairs. • Repairs are required because of normal wear and tear. • Alterations have been made to the product. • The product or any associated component has been opened without authorization or disassembled to any degree. • Damage has been caused by power washing. • Circumstances beyond the control of KING cause the product to no longer operate correctly. • Customer is not the original owner.In no event shall KING be liable for any indirect, incidental, or consequential damages from the sale or use of the product. This disclaimer applies both during and after the term of this warranty.KING disclaims liability for any implied warranties, including implied warranties of “merchantability” and “fi tness for a specifi c purpose,” after the two year term of this warranty.This warranty gives you specifi c legal rights, and you may also have other rights, which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Page 11FCC StatementThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installa-tion. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.FCC CautionAny changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.IEEE 802.11b or 802.11g operation of this product in the USA is fi rmware-limited to channels 1 through 11.The device for the band 5150-5250 MHz is only for indoor usage to reduce the potential for harmful interference to co-channel mobile satellite systems.Radiation Exposure StatementThis device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.Innovation, Science and Economic Development Canada StatementCAN ICES-3 (B)/NMB-3(B)This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is sub-ject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.For product available in the USA/Canada market, only channel 1-11 can be operated. Selection of other channels is not possible.The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology.Innovation, Science and Economic Development Canada Radiation Exposure StatementThis equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with ISED multi-transmitter product procedures.Restrictions in the 5 GHz BandThe device for the band 5150-5250 MHz is only for indoor usage to reduce the potential for harmful interference to co-channel mobile satellite systems.The maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specifi ed for point-to-point and non point-to-point operation as appropriate.Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.This radio transmitter (6873A-KWM1000) has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.Detachable antenna:• 5 dBi at 2.4 GHz, 50Ω, DipoleAdditional requirements for the band 5600-5650 MHzUntil further notice, devices subject to this Section shall not be capable of transmitting in the band 5600-5650 MHz, so that Environment Canada weather radars operating in this band are protected.Avis d’Innovation, Sciences et Développement économique CanadaCAN ICES-3 (B)/NMB-3(B)L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage; et (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.Pour les produits disponibles sur le marché aux États-Unis et au Canada, seuls les canaux de 1 à 11 peuvent être utilisés. La sélection d’autres canaux n’est pas possible.Le dispositif peut automatiquement cesser d’émettre en cas d’absence d’informations à transmettre, ou à cause d’une défaillance technique. Notez que l’objet n’est pas d’interdire la transmission des informations de contrôle ou de signalisation ou l’utilisation de codes répétitifs lorsque requis par la technologie.Avis d’Innovation, Sciences et Développement économique Canada concernant l’exposition aux radiofréquencesCe matériel est conforme aux limites établies par ISED en matière d’exposition aux radiofréquences dans un environnement non contrôlé. Ce matériel doit être installé et utilisé à une distance d’au moins 20 cm entre l’antenne et le corps de l’utilisateur.Cet appareil et son (ses) antenne(s) ne doivent pas être situés à proximité ou fonctionner en association avec une autre antenne ou un autre émetteur autre qu’en respectant les procédures d’ ISED relatives au fonctionnement des dispositifs multi-émetteurs.Restrictions dans la bande 5 GHzL’appareil pour la bande de 5150 à 5250 MHz est conçu pour usage à l’intérieur seulement afi n de réduire le potentiel d’interférences pour les systèmes mobiles par satellite qui utilisent le même canal.Le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5725-5825 MHz) doit se conformer à la limite de p.i.r.e. spécifi ée pour l’exploitation point à point et non point à point, selon le cas.De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.Le présent émetteur radio (6873A-KWM1000) a été approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d’antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué pour tout type fi gurant sur la liste, sont strictement interdits pour l’exploitation de l’émetteur.Antenne détachable:• 5 dBi à 2.4 GHz, 50Ω, DipôlePrescriptions supplémentaires pour la bande 5600-5650 MHzJusqu’à nouvel ordre, les appareils faisant l’objet de la présente section ne doivent pas transmettre dans la bande 5600-5650 MHz, afi n que les radars météorologiques d’Envi-ronnement Canada fonctionnant dans cette bande soient protégés.WIRELESS REGULATORY INFORMATION
11200 Hampshire Avenue South, Bloomington, MN 55438PH 952.922.6889 || FAX 952.922.8424 || kingconnect.com©2018 KING 23180 Rev BSimply better, by design.™All trademarks are the sole property of their respective owners.

Navigation menu