KE2 Connect 21634 KE2-EM35 Edge Manager User Manual

KE2 Connect LLC KE2-EM35 Edge Manager Users Manual

Contents

Users Manual

WAN LANKE2-EM35Edge ManagerQ.5.56 - February 201812 Chamber Drive . Washington, MO. 63090 ke2connect.io 636.266.0140
Hardware: EM-35 Router Micro USB Power CableWAN LANEthernet PortsPower USB 2.0 RS485Serial/ModBus ConnectionRestart/Factory Reset LED IndicatorsAntenna:RP-SMA Bulkhead©Copyright 2018 KE2 Connect Inc.
Specicaons:CPU 650 MHzMemory Storage 16MB Nor + 128MB Nand Dual FlashFrequency 2.4 GHzTransmission Rate 144 MbpsMax Tx Power 18 dBmProtocol 802.11 b/g/nWAN/LAN 10/100Power Input 5V / 1APower Consumpon <2WDimension 3.15 x 2.5 x 1.5 Inches/80 x 64 x 25 mm Working Temperature 32°F - 122°F / 0°C - 50°CRestart/Factory Reset: Press & hold for 3 seconds, then release to Restart the KE2-EM35. Press & hold for 10 seconds to Reset to Factory Defaults.WAN LANRestart/Factory Reset
Connect:❶ Plug in the power cable & the Internet cable. When powered up, your KE2-EM35 will broadcast a WiFi signal with the SSID: KE2EDGE-xxxxxx Plug the Internet cable (data only) into WAN.WANLANThe Internet connects to WAN❷ Connect via WiFi. The default WiFi password is printed on the boom of the KE2-EM35 - or - ❷ Connect via LAN. Plug the cable connecng your computer into LAN. WiFi: KE2EDGE-xxxxxxWiFi PW: � � � � � � � Search the SSID and connect to it.WANLANConnect your computer to LAN
❸ Seng up the KE2-EM35. Visit hp://192.168.50.1 in your browser, to set up your KE2-EM35.http://192.168.50.1Internet Connecon: Aer you have plugged in your KE2-EM35 to the WAN, you will see the main web interface. DHCP/Stac The default protocol is DHCP. If your network needs a stac seng, you can change it to Stac later, via the System Console.WAN LANWANData InPowerUSB 2.0 RS485Serial/ModBus ConnectionRestart/Factory Reset LED IndicatorsAntenna:RP-SMA Bulkhead
Data Logging EnabledDisplays active alarmsUp to 35 devices are automatically displayed on the dashboardPublished to KE2 portalData Logging NOT EnabledAlarm Notications NOT EnabledNOTPublished to KE2 portalDownload to CSV leAccess to Management Console, where setup changes are madeGreen shaded bar indicates the device is published to the KE2 portalKE2-EM35 Management Address & Firmware VersionAlarm Notications EnabledWhen log button selected, user prompted for date range.Access the Local Dashboard: To access the KE2-EM35, connect to the same net-work as the device. Since it is an Ethernet device, speaking TCP/IP, users can connect to it by simply launching their preferred web browser, and typing in the address bar: hp://em35 -or- hp://192.168.50.1. This brings the user to their local dashboard.The Local Dashboard: Once connected to the dashboard, the user will immediately see up to 35 devices displayed. Device Access For controllers on the network, simply click the IP address of the controller, to immediately connect to that controller's home page. Access the Management Console To access the Management Con-sole, select the Manage buon in the upper right corner of the dash-board screen.
Data Logging EnabledDisplays active alarmsUp to 35 devices are automatically displayed on the dashboardPublished to KE2 portalData Logging NOT EnabledAlarm Notications NOT EnabledNOTPublished to KE2 portalDownload to CSV leAccess to Management Console, where setup changes are madeGreen shaded bar indicates the device is published to the KE2 portalKE2-EM35 Management Address & Firmware VersionAlarm Notications EnabledWhen log button selected, user prompted for date range.
Management Console: A User Name and Password are required when ac-cessing the Management Console. When logged in to the Management page, users can make changes to the following sengs: Customize Portal, Alarm No-caons, Data Logging & System Updates. A detailed look at each of these follows. Login ScreenAccess KE2- EM35 (with valid subscription) from PortalData Logging NOT EnabledDevice NOTdisplayed on DashboardNOT Published to KE2 portalCustomize your portalAllow KE2 to manage/congure EM35 and all devices remotelyData logging setup Setup alarm noticationsSystem updatesAutomatically discover and display ONLY KE2 devicesAlarm Notications NOT EnabledData Logging EnabledDevice displayed on DashboardPublished to KE2 portalAlarm Notications EnabledGlobal selection - Enable setting for all devicesManagement Console will display all* of the KE2 devices connected to the Network directly or through the KE2-EM35s.*While theoretically unlim-ited, performance speed will vary based on the number of connections / devices. Tested to 50 devices with-out noticeable loss of speed
Access KE2- EM35 (with valid subscription) from PortalData Logging NOT EnabledDevice NOTdisplayed on DashboardNOT Published to KE2 portalCustomize your portalAllow KE2 to manage/congure EM35 and all devices remotelyData logging setup Setup alarm noticationsSystem updatesAutomatically discover and display ONLY KE2 devicesAlarm Notications NOT EnabledData Logging EnabledDevice displayed on DashboardPublished to KE2 portalAlarm Notications EnabledGlobal selection - Enable setting for all devicesManagement Console will display all* of the KE2 devices connected to the Network directly or through the KE2-EM35s.*While theoretically unlim-ited, performance speed will vary based on the number of connections / devices. Tested to 50 devices with-out noticeable loss of speed
Discovered KE2 devicesEnter e-mail or text addresses for notications & preferred “Subject” line (If multiple addresses are entered, use a comma to seperate each address) Setup or change the Portal Site name and PasswordEstablish the frequency that data points are loggedUpdates & advanced congurationsManagement Console Features: AlertsDevicesAccess
LogsManagement Console Features (connued): System

Navigation menu