Juniper Networks 5GTADSLW NetScreen-5GT ADSL Wireless User Manual NetScreen 5GT ADSL User s Guide

Juniper Networks NetScreen-5GT ADSL Wireless NetScreen 5GT ADSL User s Guide

UserManual.wiki >

Juniper Networks >

5GTADSLW User Manual

User Manual

NETSCREEN-5GT WIRELESSUser’s GuideVersion 5.0.0 P/N 093-XXXX-000 Rev. Beta

NetScreen-5GT Wireless 1ContentsPreface........................................................................................3Organization ............................................................................................... 3WebUI Conventions .................................................................................... 4CLI Conventions .......................................................................................... 4NetScreen Publications ............................................................................... 5Chapter 1 Connecting the Device.........................................................................7Connecting the NetScreen Device to Your Networks ................................. 7Connecting the Device to an Untrusted Network............................................ 7Connecting the ADSL Port ...........................................................................7Connecting the Untrusted Port ....................................................................9Connecting the Device to Your Internal Network or Workstations.................... 9Connecting Trusted Ethernet Ports ..............................................................9Using the Wireless Interface ........................................................................9Connecting the Power .............................................................................. 10Rack Mounting (Optional) ........................................................................ 10Chapter 2 Configuring the Device.......................................................................13Accessing the Device ............................................................................... 13Using the WebUI............................................................................................. 13Using Telnet ................................................................................................... 14Using a Console Connection......................................................................... 15Required Configuration ............................................................................ 15Changing the Admin Name and Password................................................... 16Setting the Date and Time............................................................................. 16Wireless Configuration .............................................................................. 17Configuring the Wireless Network .................................................................. 18ADSL Configuration ................................................................................... 19Configuring the ADSL Interface ..................................................................... 20Adding Virtual Circuits to an ADSL Interface.................................................. 20VPI/VCI and Multiplexing Method.................................................................. 21PPPoE or PPPoA.............................................................................................. 22Annex B Mode............................................................................................... 22Static IP Address and Netmask...................................................................... 23Optional Configuration ............................................................................. 24Restricting Management............................................................................... 25Configuring Additional Policies...................................................................... 25Operational Mode ........................................................................................ 25Changing the Port Mode............................................................................... 26Configuring a Backup Untrust Zone Interface................................................ 28

Contents2User’s GuideChanging the Trust Interface Address ........................................................... 29Verifying External Connectivity ..................................................................29Resetting the Device to Factory Defaults ..................................................29Using the Reset Pinhole.................................................................................. 30Chapter 3 Hardware Descriptions.........................................................................31Port and Power Connectors ......................................................................31Status LEDs ................................................................................................32Main Status LEDs for the Device..................................................................... 33Port Status LEDs.............................................................................................. 33Specifications .................................................................................................... A-35

NetScreen-5GT Wireless 3PrefaceThe Juniper Networks NetScreen-5GT Wireless device provides IPSec VPN and firewall services for a branch office or a retail outlet that uses an integrated wireless 802.11b/g interface. The NetScreen-5GT Wireless device uses the same firewall, VPN, Antivirus, Deep Inspection, and traffic management technology as NetScreen’s high-end central site products.Juniper Networks offers three models of the NetScreen-5GT Wireless device:•The Wireless only model.•The Wireless with Annex A model supports ADSL over standard telephone lines (POTS).•The Wireless with Annex B model supports ADSL over Integrated Services Digital Network (ISDN).All models support up to four virtual Access Points (APs). Both ADSL models support ANSI TI.413 Issue 2, ITU G.992.1 (G.dmt), and ITU 992.2 (G.lite) standards.Each model supports three versions of the device:•The 10-user version supports up to 10 users.•The Plus version supports an unrestricted number of users.•The Extended version provides the same capabilities as the Plus version, with additional features: High Availability (NSRP Lite), the DMZ security zone, and additional sessions and tunnel capacity.ORGANIZATIONThis manual has three chapters and one appendix.Chapter 1, “Connecting the Device” describes how to connect the device to your network, connect the power, connect an antenna, and install the NetScreen-5GT Wireless device in a rack.Chapter 2, “Configuring the Device” describes the default settings and operation of the NetScreen-5GT Wireless (ADSL) and the configuration required to use the device.Chapter 3, “Hardware Descriptions” provides an overview of the NetScreen-5GT Wireless ports, LEDs, and power requirements.Appendix A, “Specifications” provides a list of physical specifications about the NetScreen-5GT Wireless device.

Preface4User’s GuideWEBUI CONVENTIONSThroughout this book, a chevron ( > ) is used to indicate navigation through the WebUI by selecting menu options and links.Example: Objects > Addresses > List > NewTo access the new address configuration dialog box:1. Click Objects in the menu column.The Objects menu option expands to reveal a subset of options for Objects.2. (Applet menu1) Hover the mouse over Addresses.(DHTML menu) Click Addresses.The Addresses option expands to reveal a subset of options for Addresses.3. Click List.The address book table appears.4. Click the New link in the upper right corner.The new address configuration dialog box appears.CLI CONVENTIONSThe following conventions are used when presenting the syntax of a command line interface (CLI) command:•Anything inside square brackets [ ] is optional.•Anything inside braces { } is required.•If there is more than one choice, each choice is separated by a pipe ( | ). For example,set interface { ethernet1 | ethernet2 | ethernet3 } managemeans “set the management options for the ethernet1, ethernet2, or ethernet3 interface”.•Variables appear in italic. For example:set admin user name1 password xyz1. You can choose either the applet or DHTML menu types by clicking the Toggle Menu option at the bottom of the menu column.

NetScreen PublicationsNetScreen-5GT Wireless 5When a CLI command appears within the context of a sentence, it is in bold (except for variables, which are always in italic). For example: “Use the get system command to display the serial number of a NetScreen device.”NETSCREEN PUBLICATIONSTo obtain technical documentation for any Juniper Networks NetScreen product, visit www.juniper.net/techpubs/.For technical support, open a support case using the Case Manager link at http://www.juniper.net/support/ or call 1-888-314-JTAC (within the United States) or 1-408-745-9500 (outside the United States).If you find any errors or omissions in the following content, please contact us at the e-mail address below:techpubs-comments@juniper.netNote: When typing a keyword, you only have to type enough letters to identify the word uniquely. For example, typing set adm u joe j12fmt54 is enough to enter the command set admin user joe j12fmt54. Although you can use this shortcut when entering commands, all the commands documented here are presented in their entirety.

Preface6User’s Guide

NetScreen-5GT Wireless 71Chapter 1Connecting the DeviceThis chapter describes how to connect the NetScreen-5GT Wireless device to the network, connect the power, and connect an antenna. If you are using the optional NetScreen-5GT Wireless rack mount kit, then use the rack mounting instructions that are included at the end of this chapter.CONNECTING THE NETSCREEN DEVICE TO YOUR NETWORKSThe NetScreen device provides firewall and general security for your networks when it is placed between your internal networks and the Untrusted network. This section describes the physical connections.Connecting the Device to an Untrusted NetworkDepending upon which model of the NetScreen-5GT Wireless device you have, you can connect to the Untrusted network in one of the following ways:•Through an ADSL connection from the ADSL port on the NetScreen device.•Through an Ethernet connection from the Untrusted port on the NetScreen device.Connecting the ADSL PortConnect the provided ADSL cable from the ADSL port on the NetScreen-5GT Wireless ADSL device to your telephone outlet. The ADSL port on the Annex A version of the device uses an RJ-11 connector, while the Annex B version uses an RJ-45 connector. In the case of Annex B models, the cable you connect from the ADSL port to the telephone outlet is identical in appearance and wiring to a straight-through 10 Base-T Ethernet cable.Note: For safety warnings and instructions, refer to the NetScreen Safety Guide. The instructions in this guide warn you about situations that could cause bodily injury. Before working on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.Warning: Make sure that you do not inadvertently connect the Console, Modem, or Ethernet ports on the NetScreen device to the telephone outlet.

Chapter 1 Connecting the Device8User’s GuideThe ADSL line is your primary connection to an outside network. For a backup data link to an outside network, you can either connect an Ethernet cable from the Untrusted port on the NetScreen-5GT Wireless ADSL device to an external router, DSL modem, or cable modem, or connect a serial cable from the Modem port on the device to an external modem.Connecting Splitters and MicrofiltersA signal splitter divides the telephone signal into low-frequency voice signals for voice calls and high-frequency data signals for data traffic. Your service provider usually installs the splitter as part of the equipment that connects your site’s telephone lines to the provider’s network.There are also splitters that you may be able to install yourself, depending upon your service provider equipment. If you are installing such a splitter yourself, then connect the ADSL cable from the NetScreen device and the telephone line to the appropriate connectors (for example, “data” or “voice”) on the splitter. You connect the other end of the splitter to the telephone outlet.You may need to install a microfilter on each telephone, fax machine, answering machine, or analog modem that connects to the ADSL line. The microfilter filters out high-frequency noise on the telephone line. You install the microfilter on the telephone line between the telephone, fax machine, answering machine, or analog modem and the voice connector on the splitter.The following shows an example of a microfilter and a splitter that you install on your site. (You must obtain the appropriate microfilters or splitters from your service provider.)Warning: You cannot connect both the Untrusted port and the Modem port on the device to an outside network at the same time.Telephone OutletSplitterMicrofilterADSL Cable

Connecting the NetScreen Device to Your NetworksNetScreen-5GT Wireless 9Connecting the Untrusted PortYou can establish an internet connection to an external router, DSL modem, or cable modem, and provide firewall and general security for your network. To establish a high-speed connection, connect the provided Ethernet cable from the Untrusted interface on the NetScreen-5GT Wireless device to the external router or modem. The NetScreen-5GT Wireless device autosenses the correct speed, duplex, and polarity settings.If you are using the NetScreen-5GT Wireless ADSL device, then refer to sections “Connecting the ADSL Port” on page 7 and “Connecting Splitters and Microfilters” on page 8 for ADSL connection instructions.Connecting the Device to Your Internal Network or WorkstationsYou can connect your LAN or workstation using one or both of the following ways:•Connecting through one or more of the Trusted Ethernet ports on the NetScreen device.•Using a wireless interface on the NetScreen device.Connecting Trusted Ethernet PortsThe NetScreen-5GT Wireless device contains four Trusted Ethernet ports. You can use one or more of these ports to connect to LANs via switches or hubs. You can also connect one or all of the ports directly to workstations, eliminating the need for a hub or switch. You can use either cross-over or straight-through cables to connect the Ethernet ports to other devices.Using the Wireless InterfaceIf you are using the wireless interface, you need to connect the provided antennae on the device. If you have the standard 2dB omnidirectional antennae, then screw them onto the posts marked A and B at the back of the device. Antenna A is located next to the power cord connection. Bend the antennae at their elbows, making sure not to put pressure on the bulkhead connector. If you are using the optional high-gain antenna, then follow the antenna’s connection instructions.

Chapter 1 Connecting the Device10 User’s GuideCONNECTING THE POWERTo connect the power to the NetScreen-5GT Wireless device:1. Plug the DC connector end of the power cable into the DC power receptacle on the back of the device.2. Plug the AC adapter end of the power cable into an AC power source.RACK MOUNTING (OPTIONAL)With a NetScreen-5GT Wireless rack-mount kit, you can mount one or two NetScreen-5GT Wireless devices in a standard 19-inch equipment rack. The NetScreen-5GT Wireless rack-mount kit includes installation instructions and a rack-mounting tray. The dimensions of the tray are as follows:In addition to the NetScreen-5GT Wireless device(s), rack-mount kit, and equipment rack, you also need the following:•Phillips-head screwdriver•Four screws that match the thread size of the equipment rackTo mount the device in a rack:1. Use the Phillips-head screwdriver to remove the two screws from the underside of each NetScreen-5GT Wireless device that you intend to mount. The screws are located on the underside of the NetScreen-5GT Wireless near the front panel. (Keep the screws for use in the next step.)2. Insert the NetScreen-5GT Wireless devices on the rack-mount tray and screw them to the tray with the screws that you removed in step 1.Warning: NetScreen recommends using a surge protector for the power connection.Width: 48.26 cm. 19 in. Height: 4.013 cm. 1-5/8 in. (1 rack unit)Depth: 33.655 cm. 13-1/4 in.

Rack Mounting (Optional)NetScreen-5GT Wireless 113. Screw the left and right tray plates to the equipment rack.You can run power cords and Ethernet cables through the openings in the floor of the tray or out the depressions in the back wall. You can also use the space behind the devices to hold power supplies.

Chapter 1 Connecting the Device12 User’s Guide

NetScreen-5GT Wireless 132Chapter 2Configuring the DeviceThis chapter describes how to configure a NetScreen-5GT Wireless device after you have connected it. If you are accessing the device for the first time using the ScreenOS WebUI graphical interface, then you can use the Initial Configuration Wizard to guide you through the basic configuration. To use the Initial Configuration Wizard, refer to the Juniper Networks NetScreen-5GT Wireless Getting Started Guide.Topics explained in this chapter include:•Accessing the Device•Required Configuration•Wireless Configuration•ADSL Configuration•Optional Configuration•Verifying External Connectivity•Resetting the Device to Factory DefaultsACCESSING THE DEVICEThis section describes how to access your NetScreen device using the WebUI, Telnet, or a Console connection.Using the WebUIThe ScreenOS WebUI is a graphical interface that is available through a web browser. To use the WebUI, you must be on the same subnetwork as the NetScreen device. To access the NetScreen-5GT Wireless device with the WebUI management application:1. Connect your workstation (or your LAN hub) to Trust Ethernet port labeled 1.2. Make sure that your workstation is on the same subnetwork as the NetScreen device. If there are no DHCP servers available on the LAN, then the NetScree-5GT Wireless device acts as a DHCP server. The NetScreen device provides addresses from 192.168.1.33 to 192.168.1.xx.Note: After you configure the NetScreen device and verify connectivity to the Internet, you must register your product at www.juniper.net/support/ so that certain ScreenOS services, such as internal antivirus or Deep Inspection Signature Service, can be activated on the device. After registering your product, use the WebUI to obtain the subscription for the service. For more information about registering your product and obtaining subscriptions for specific services, see the “System Parameters” chapter in the “Fundamentals” volume of the NetScreen Concepts & Examples ScreenOS Reference Guide for ScreenOS 5.0.0.

Chapter 2 Configuring the Device14 User’s Guide3. Launch your browser, enter the default IP address for the Trust interface in the URL field, and then press Enter. For example, enter the following in the URL field:192.168.1.1The NetScreen WebUI software displays the login prompt.4. If you have not yet changed the default user name and password, then enter netscreen in both the User Name and Password fields, and then click Login. (Use lowercase letters only. The User Name and Password fields are both case sensitive.)Using TelnetTelnet is an application that allows you to access devices through an IP network. To configure the device using Telnet, enter ScreenOS Command Line Interface (CLI) commands in a Telnet session from your workstation.1. Connect your workstation (or your LAN hub) to Trust Ethernet port labeled 1.2. Start a Telnet client application to the default IP address for the Trust interface. For example, enter the following:telnet 192.168.1.13. If you have not yet changed the default user name and password, then type netscreen in both the login and password prompts. (Use lowercase letters only. The login and password fields are both case sensitive.)Note: If you choose to skip the Initial Configuration Wizard, then the WebUI login prompt automatically appears.Note: You can also access NetScreen devices using Secure Shell (SSH) applications. Refer to the “Administration” chapter in the “Administration” volume of the NetScreen Concepts & Examples ScreenOS Reference Guide for ScreenOS 5.0.0 for more information.

Required ConfigurationNetScreen-5GT Wireless 15Using a Console ConnectionThe Console port on the NetScreen-5GT Wireless device allows you to access the device through a serial cable connected to your workstation or terminal. To configure the device using a console connection, enter ScreenOS CLI commands on your terminal or in a terminal emulation program on your workstation.To establish a console connection:1. Plug the female DB-9 end of the serial cable into the serial port of your computer. (Be sure that the DB-9 connector is seated properly in the port.)2. Plug the other end of the DB-9 connector into the RJ-45 DB-9 port. (Be sure that the DB-9 connector is seated properly in the RJ-45 DB-9 port.)3. Plug the male RJ-45 end of the serial cable into the Console port of the NetScreen-5GT Wireless device. (Be sure that the RJ-45 connector is seated properly in the port.) 4. Launch a serial terminal emulation program. (A commonly-used terminal program is Hilgreave HyperTerminal.) The required settings to launch a console session with your NetScreen-5GT Wireless device are as follows:– Baud Rate: 9600–Parity: No– Data Bits: 8–Stop Bit: 1– Flow Control: None5. If you have not yet changed the default user name and password, enter netscreen in both the login and password prompts. (Use lowercase letters only. The login and password fields are both case sensitive.)REQUIRED CONFIGURATIONThis section describes the configurations that you need to complete to use the NetScreen-5GT Wireless devices.Note: For the console connection, use a serial cable with a male RJ-45 connector on one end and female DB-9 connector on the other end. See Appendix A, Specifications for the connector pinouts for the serial cable.Note: If you have any problems completing a configuration and you need to restore the device to its default settings, see “Resetting the Device to Factory Defaults” on page 29.

Chapter 2 Configuring the Device16 User’s GuideChanging the Admin Name and PasswordBecause all NetScreen products use the same default admin name and password (netscreen), it is highly advisable to change your admin name and password immediately. To change the administrator name and password from “netscreen” and “netscreen” to “darwin1” and “1240jes”:WebUIConfiguration > Admin > Administrators > Edit (for the netscreen Administrator Name): Enter the following, and then click OK:Administrator Name: darwin1Old Password: netscreenNew Password: 1240jesConfirm New Password: 1240jesCLIset admin name darwin1set admin password 1240jessaveFor information on creating different levels of administrators, see the “Administration” chapter in the “Administration” volume of the NetScreen Concepts & Examples ScreenOS Reference Guide for ScreenOS 5.0.0.Setting the Date and TimeThe time set on the NetScreen device affects events such as the setup of VPN tunnels and the timing of schedules. The easiest way to set the date and time on the NetScreen device is to synchronize the system clock on the NetScreen device with the clock on your computer. To do this in the WebUI:1. Configuration > Date/Time: Click the Sync Clock with Client button.A pop-up message prompts you to specify if you have enabled the daylight saving time option on your computer clock.2. Click Yes to synchronize the system clock and adjust it according to daylight saving time or No to synchronize the system clock without adjusting it for daylight saving time.You can also use the CLI set clock command in a Telnet or Console session to manually enter the date and time.Note: Passwords do not display in the WebUI when you type them in.

Wireless ConfigurationNetScreen-5GT Wireless 17WIRELESS CONFIGURATIONThis section provides information for configuring the wireless interface on the NetScreen device. Depending on the type of license you have installed, you can configure up to four virtual Access Points on a NetScreen-5GT Wireless device. The interface to zone bindings are static, and there are no wireless interfaces assigned to the Untrust zone. You must configure at least one wireless interface on the NetScreen device to create a wireless LAN (WLAN).The figure below shows the default configuration for the NetScreen-5GT Wireless.The default wireless interface has a predefined name “wireless2”. The Trust and wireless2 interfaces are bound to the Trust zone and are configured with the subnetwork addresses 192.168.1.1/24 and 192.168.2.1/24, respectively. This means that all devices that you connect to in the Trust zone must be in the same subnetwork as either the trust or wireless2 interface and have IP addresses in one of the two subnetworks. The NetScreen device is also configured to assign IP addresses for the 192.168.1.1/24 and 192.168.2.1/24 subnetworks to your devices. For more information, refer to “Changing the Trust Interface Address” on page 29.Note: If you are operating the NetScreen-5GT Wireless device in a country other than the United States or Japan, then you must use the set wlan country-code command before a WLAN connection can be established. This command sets the selectable channel range and transmit power level.To InternetWzone1 ZoneTrust Interface192.168.1.1/24 wireless2 Interface 192.168.2.1/24 Trust ZoneHubwireless1 Interface (no IP address)External router, switch, or Hub

Chapter 2 Configuring the Device18 User’s GuideBy default, the wireless1 interface is bound to the Wzone1 zone and does not have an IP address assigned to it. If you want to use the wireless1 interface, then you must configure an IP address for it. Refer to the NetScreen-5GT Wireless New Features Guide for more information.The NetScreen device allows any type of traffic to the Internet that originates from devices in your Trust zone, but does not allow any traffic that originates in the Internet to reach your network. You can configure additional restrictions; refer to “Configuring Additional Policies” on page 25.Configuring the Wireless NetworkWireless networks consist of names referred to as Service Set Identifiers (SSIDs). Specifying an SSID allows you to have multiple wireless networks residing in the same location without interfering with each other. You can have a maximum of eight SSIDs configured on each device. Once the SSID name is set, you can configure SSID attributes.To set the SSID name netscreen open, allow wireless network connectivity, and activate the wireless2 interface:WebUIWireless > SSID > New: Enter the following, and then click OK:SSID: “netscreen open”Wireless Interface Binding: wireless2 (select)Activate Changes > click the Activate Changes buttonCLIset ssid name “netscreen open”set ssid “netscreen open” authentication open encryption noneset ssid “netscreen open” interface wireless2exec wlan reactivateOnce you have set an SSID to the wireless2 interface, you can access the device using the default wireless2 interface IP address in the steps provided with “Accessing the Device” on page 13 to configure the device. Refer to the NetScreen-5GT Wireless New Features Guide for configuration examples, SSID attributes, and CLI commands relating to wireless security configurations.Note: You cannot use the wireless2 interface to access the Initial Configuration Wizard (ICW). The ICW can only be accessed with the physical Trust interface connection.

ADSL ConfigurationNetScreen-5GT Wireless 19ADSL CONFIGURATIONThis section describes the default settings and operation of the NetScreen-5GT Wireless ADSL Annex A and B devices as they are shipped from the factory. These default settings are such that, in most cases, there are only a few items that you must configure.This section describes the following configurations for the Untrust zone interface:•Configuring the ADSL Interface•VPI/VCI and Multiplexing Method•PPPoE or PPPoA•Annex B Mode•Configuring a Backup Untrust Zone Interface•Static IP Address and NetmaskThe figure below shows the default configuration for the NetScreen-5GT Wireless ADSL.The ADSL interface has the predefined name “adsl1” and is the main connection from your network to the Internet. To allow the NetScreen device (and the devices on your network) to connect to the Internet, you must configure the adsl1 interface according to information obtained from your service provider. Refer to “Configuring the ADSL Interface” on page 20.Note: If you have any problems completing a configuration and you need to restore the device to its default settings, see “Resetting the Device to Factory Defaults” on page 29.Trust Interface192.168.1.1/24 To InternetTelephone OutletHubADSL Interface (adsl1)wireless2 Interface192.168.2.1/24 wireless1 interfaceTrust ZoneWzone1

Chapter 2 Configuring the Device20 User’s GuideThe NetScreen device allows any type of traffic to the Internet that originates from devices in your Trust zone, but does not allow any traffic that originates in the Internet to reach your network. You can configure additional restrictions; refer to “Configuring Additional Policies” on page 25.Configuring the ADSL InterfaceYour network uses the ADSL interface “adsl1” on the NetScreen device to connect to the service provider’s network through an Asynchronous Transfer Mode (ATM) virtual circuit. You can configure additional virtual circuits by creating ADSL subinterfaces (see “Adding Virtual Circuits to an ADSL Interface” on page 20 for more information).In the WebUI, navigate to the Network > Interfaces page to see a list of the current interfaces on the NetScreen device. If you are using a Telnet or Console session, enter the CLI command get interface. You should see that the adsl1 interface is bound to the Untrust zone. If you used the Initial Configuration Wizard to configure the device, then there may be an IP address and netmask already assigned to the adsl1 interface.You must configure the adsl1 interface to enable the NetScreen device to connect to the service provider’s network. To do this, you must obtain the following information from your service provider:•Virtual Path Identifier and Virtual Channel Identifier (VPI/VCI) values•Asynchronous Transfer Mode (ATM) Adaptation Layer 5 (AAL5) multiplexing method, which can be one of the following:– Virtual Circuit (VC)-based multiplexing, in which each protocol is carried over a separate ATM virtual circuit– Logical Link Control (LLC) encapsulation, which allows several protocols to be carried on the same ATM virtual circuit (this is the default multiplexing method)•User name and password assigned by the service provider for connection to the service provider’s network using either the Point-to-Point Protocol over Ethernet (PPPoE) or Point-to-Point Protocol over ATM (PPPoA)•Authentication method, if any, provided for the PPPoE or PPPoA connection•Optionally, a static IP address and netmask value for your networkAdding Virtual Circuits to an ADSL InterfaceTo add virtual circuits, you create sub-interfaces to the ADSL interface. You can create up to ten ADSL subinterfaces. For example, to create a new subinterface adsl1.1 that is bound to the user-defined zone named “Corp1”:Note: If you do not want to use the ADSL interface, then you can bind it to the Null zone with the set interface adsl1 zone null command. If you use the Initial Configuration Wizard to configure the device, you can choose to not use the ADSL interface as the default interface to the Untrust zone.

ADSL ConfigurationNetScreen-5GT Wireless 21WebUINetwork > Interfaces > New ADSL Sub-IF: Enter the following, and then click Apply:Interface Name: adsl1.1VPI/VCI: 0/35Zone Name: Corp1 (select)CLIset interface adsl1.1 pvc 0 35 zone corp1saveYou need to configure an ADSL subinterface in the same way as the main ADSL interface, including setting the VPI/VCI values, as described in “Configuring the ADSL Interface” on page 20. You configure an ADSL subinterface independently of the main ADSL interface, that is, you can configure a different multiplexing method, VPI/VCI, and PPP client on the subinterface than the main ADSL interface. You can also configure a static IP address on a subinterface, even if the main ADSL interface does not have a static IP address. Note that a subinterface and the main ADSL interface can use the same VPI/VCI values if one interface is configured for PPPoA and the other for PPPoE and they both use LLC multiplexing.VPI/VCI and Multiplexing MethodYour service provider assigns a VPI/VCI pair for each virtual circuit connection. For example, you may receive the VPI/VCI pair 1/1, which means a VPI value of 1 and a VCI value of 1. These values must match the values that the service provider has configured on the subscriber’s side of the digital subscriber line access multiplexer (DSLAM).To configure the VPI/VCI pair 1/1 on the adsl1 interface:WebUINetwork > Interfaces > Edit (for the adsl1 interface): Enter 1/1 in the VPI/VCI field, and then click Apply.CLIset interface adsl1 pvc 1 1saveBy default, the NetScreen-5GT Wireless ADSL device uses LLC-based multiplexing for each virtual circuit. To configure the VPI/VCI 1/1 on the adsl1 interface and use LLC encapsulation on the virtual circuit:WebUINetwork > Interfaces > Edit (for the adsl1 interface): Enter the following, and then click Apply:VPI/VCI: 1 / 2Multiplexing Method: LLC (selected)

Chapter 2 Configuring the Device22 User’s GuideCLIset interface adsl1 pvc 1 1 mux llcsavePPPoE or PPPoAThe NetScreen device includes both PPPoE and PPPoA clients to connect to the service provider’s network over the ADSL link. PPPoE is the most common form of ADSL encapsulation and is intended for termination on each host on your network. PPPoA is used primarily for business class service as PPP sessions can be terminated on the NetScreen device. To allow the NetScreen device to connect to the service provider’s network, you need to configure the user name and password assigned by the service provider. The configuration for PPPoA is similar to the configuration for PPPoE.To configure the user name “roswell” and password “area51” for PPPoE and bind the PPPoE configuration to the adsl1 interface:WebUINetwork > PPPoE > New: Enter the following, and then click OK:PPPoE Instance: poe1Bound to Interface: adsl1 (select)Username: roswellPassword: area51CLIset pppoe name poe1 username roswell password area51set pppoe name poe1 interface adsl1saveThere are other PPPoE or PPPoA parameters that you can configure on the NetScreen device, including method of authentication (by default, the NetScreen device supports either Challenge Handshake Authentication Protocol or Password Authentication Protocol), idle timeout (default is 30 minutes), and so on. Ask your service provider if there are additional PPPoE or PPPoA parameters that you need to configure to enable proper communications with the service provider’s server.Annex B ModeIf you connect the Annex B model of the NetScreen-5GT Wireless ADSL device to a Deutsch Telecom ADSL line, then you must configure the physical interface on the ADSL port for operation with this equipment. To do this:Note: The NetScreen device supports only one PPPoE session on each virtual circuit.

ADSL ConfigurationNetScreen-5GT Wireless 23WebUINetwork > Interfaces > Edit (for the adsl1 interface): Select DT for the Annex B Mode, and then click Apply.CLIset interface adsl1 phy annex-b-mode dtsaveYou do not need to configure this setting if you are using the Annex A model of the device or if you are connecting the device to non-Deutsch Telecom equipment.Static IP Address and NetmaskIf your ISP gave you a specific, fixed IP address and netmask for your network, then configure the IP address and netmask for the network and the IP address of the router port connected to the NetScreen device. You need to also specify that the device use the static IP address. (By default, the NetScreen device acts as a PPPoE or PPPoA client and receives an IP address for the ADSL interface through negotiations with the PPPoE or PPPoA server.) To configure the static IP address 1.1.1.1/24 for the network:WebUINetwork > Interfaces > Edit (for the adsl1 interface): Enter the following, and then click Apply:IP Address/Netmask: 1.1.1.1/24Static IP: (select)CLIset interface adsl1 ip 1.1.1.1/24set pppoe name poe1 static-ipsaveorset interface adsl1 ip 1.1.1.1/24set pppoa name poa1 static-ipsaveNote: You need to configure a PPPoE or PPPoA instance and bind it to the adsl1 interface, as described in the previous section. Make sure that you select “Obtain IP using PPPoE” or “Obtain IP using PPPoA” and the name of the PPPoE or PPPoA instance.

Chapter 2 Configuring the Device24 User’s GuideTo use Domain Name System (DNS) for domain name and address resolution, the computers in your network need to have the IP address of at least one DNS server. If the NetScreen device receives an IP address for the ADSL interface through PPPoE or PPPoA, then it also automatically receives IP addresses for the DNS server(s). If the computers in your network obtain their IP addresses from the DHCP server on the NetScreen device, then the computers also obtain these DNS server address(es). If you assign a static IP address to the ADSL interface, then the service provider must give you the IP address(es) of the DNS server(s). You can either configure the DNS server address on each computer in your network or configure the DHCP server on the Trust zone interface so that it provides the DNS server address to each computer.To configure the DHCP server on the Trust interface to provide the DNS server address 1.1.1.152 to computers in your network:WebUINetwork > DHCP > Edit (for the Trust interface) > DHCP Server: Enter 1.1.1.152 for DNS1, and then click Apply.CLIset interface trust dhcp server option dns1 1.1.1.152saveOPTIONAL CONFIGURATIONThis section describes the following features on the NetScreen-5GT Wireless devices that you may want to configure:•Restricting Management•Configuring Additional Policies•Operational Mode•Changing the Port Mode•Configuring a Backup Untrust Zone Interface•Changing the Trust Interface AddressNote: Not all of the optional configurations are described in detail in this manual. Refer to the appropriate chapters in the NetScreen Concepts & Examples ScreenOS Reference Guide for ScreenOS 5.0.0 for more information.

Optional ConfigurationNetScreen-5GT Wireless 25Restricting ManagementBy default, anyone in your network can manage the NetScreen device if they know the login and password. You can configure the NetScreen device to be managed only from one or more specific hosts on your network. (And you can choose which services — for example, WebUI, Telnet, ping — you want enabled on the NetScreen device.) Refer to the “Administration” chapter in the “Administration” volume of the NetScreen Concepts & Examples ScreenOS Reference Guide for ScreenOS 5.0.0.Configuring Additional PoliciesThe NetScreen-5GT Wireless devices are configured with a default policy that permits workstations in the Trust zone of your network to access any kind of service with outside computers, while outside computers are not allowed to access or start sessions with your workstations. You can configure policies that direct the NetScreen device to permit outside computers to start specific kinds of sessions with your computers. To create or modify policies, refer to the “Policies” chapter in the “Fundamentals” volume of the NetScreen Concepts & Examples ScreenOS Reference Guide for ScreenOS 5.0.0.Operational ModeThe operational mode is the way an interface on a NetScreen device processes traffic between zones. By default, the NetScreen-5GT Wireless devices operates in Route mode with network address translation (NAT) enabled on the Trust interface. This means that when devices in the Trust zone send traffic to the Internet, the NetScreen device replaces the original source IP addresses with the IP address of the Untrust interface. While the NetScreen device assigns “private” IP addresses to the devices in your network, these addresses remain hidden to computers outside your network.If all devices in your network have public IP addresses, then you can configure the NetScreen device for Route mode without NAT enabled. In Route mode without NAT enabled, the NetScreen device routes traffic by checking IP addresses. For more information about configuring the device for Route mode without NAT enabled, refer to the “Interface Modes” chapter in the “Fundamentals” volume of the NetScreen Concepts & Examples ScreenOS Reference Guide for ScreenOS 5.0.0.

Chapter 2 Configuring the Device26 User’s GuideChanging the Port ModeThe port mode is the binding of physical ports, logical interfaces, and zones.The following table summarizes the port, interface, and zone bindings provided by the port modes that are available on the NetScreen-5GT Wireless devices:Warning: Changing the port mode removes any existing configurations on the NetScreen device. Therefore, change the port mode before configuring the device.Port Nameaa. As labeled on the NetScreen appliance chassis.Trust-Untrust Port Modebb. Default port mode.Home-Work Port Mode Trust/Untrust/DMZ (Extended) ModeInterface Zone Interface Zone Interface Zone1trust Trust ethernet1 Work ethernet1 Trust2trust Trust ethernet1 Work ethernet1 Trust3trust Trust ethernet2 Home ethernet2 DMZ4trust Trust ethernet2 Home ethernet2 DMZUntrusted untrust Nullcc. You can configure a backup interface to the Untrust zone, using either the Untrusted Ethernet port or the Modem port. See “Configuring a Backup Untrust Zone Interface” on page 28.ethernet4 Nullcethernet4 NullcModem serial Nullcserial Nullcserial NullcADSLdd. Only available on the ADSL Annex A and B devices.adsl1 Untrust or V1-Untrust adsl1 Untrust adsl1 Untrustwireless1 Wzone1 wireless1 Wzone1 wireless1 Wzone1wireless2 Trust or V1-Trust wireless2 Work wireless2 Trustwireless3 Home wireless3 DMZwireless4 Wzone2Port NameaDual Untrustb Port Mode Combinedc Port ModeInterface Zone Interface Zone1ethernet1 Trust ethernet1 Work2ethernet1 Trust ethernet2 Home3ethernet1 Trust ethernet2 Home4ethernet2 Untrust ethernet3 UntrustUntrusted ethernet3 Untrust ethernet4 Untrust

Optional ConfigurationNetScreen-5GT Wireless 27To change the NetScreen device to the Home-Work port mode:WebUIConfiguration > Port Mode: Select Home-Work from the drop-down list, and then click Apply.At the following prompt, click OK:Operational mode change will erase current configuration and reset the device, continue?CLIexec port-mode home-workAt the following prompt, enter y (for yes):Change port mode from <trust-untrust> to <home-work> will erase system configuration and reboot boxAre you sure y/[n]? yModem serial Nullcserial NullcADSLdadsl1 Untrust or V1-Untrust adsl1 Untrustwireless1 Wzone1 wireless1 Wzone1wireless2 Trust or V1-Trust wireless2 Workwireless3 Homea. As labeled on the NetScreen appliance chassis.b. Only available on the Wireless only device.c. Only available on the Wireless only device.d. Only available on the Wireless ADSL Annex A and B devices.Port NameaDual Untrustb Port Mode Combinedc Port ModeInterface Zone Interface Zone

Chapter 2 Configuring the Device28 User’s GuideConfiguring a Backup Untrust Zone InterfaceBy default, on NetScreen-5GT Wireless ADSL device, the adsl1 interface is the primary connection to an outside network. Each port mode available on the NetScreen-5GT Wireless ADSL device allows you the option of connecting either the Untrusted Ethernet port or the Modem port as a backup connection to the outside network (see “Changing the Port Mode” on page 26). You must bind the backup interface to the Untrust zone and configure the interface appropriately.For example, to bind the Untrust interface to the Untrust zone:WebUINetwork > Interfaces > Edit (for the untrust interface): Select Untrust from the Zone Name drop-down list, and then click OK.CLIset interface untrust zone untrustsaveYou also need to set a static IP address for the Untrust interface, or specify whether the IP address for the interface is obtained via either DHCP or PPPoE. See the “Interfaces” chapter in the “Fundamentals” volume of the NetScreen Concepts & Examples ScreenOS Reference Guide for ScreenOS 5.0.0 for more information about configuring interface parameters.When the adsl1 interface and either the Ethernet interface (named untrust or ethernet3, depending upon the port mode) or the serial interface is bound to the Untrust zone, interface failover is automatically configured. That is, if the adsl1 interface becomes unavailable, the NetScreen device automatically sends traffic to the backup interface. The device automatically sends traffic to the adsl1 interface when the adsl1 interface is again available.You can also manually force failover and failback on the adsl1 interface. For more information, see the “Interface Redundancy” chapter in the “High Availability” volume of the NetScreen Concepts & Examples ScreenOS Reference Guide for ScreenOS 5.0.0.Note: You can configure only one backup interface, using either the Untrusted Ethernet port or Modem port connection. If you use the Untrusted port for the backup connection, then configure the Untrust interface in Trust-Untrust port mode or the ethernet3 interface for other port modes. If you use the Modem port for the backup connection, then configure the serial interface for all port modes.Note: Only the adsl1 interface is affected by failover. That is, if you have also configured ADSL subinterfaces, the subinterfaces do not fail over to the backup interface.

Verifying External ConnectivityNetScreen-5GT Wireless 29Changing the Trust Interface AddressYou can change the IP address and netmask of the Trust and wireless interfaces if necessary. (Remember that when the Trust interface is in NAT mode, the IP addresses of devices in your network are never seen by computers outside your network; outside computers see only the IP address of the Untrust interface.) For example, you might need to change the Trust interface to match the IP addresses that already exist on your network. If you change the IP address and netmask of the Trust interface, then you also need to change either the range of addresses that the NetScreen device assigns via DHCP to devices in the network or disable the DHCP server on the Trust interface.If the computers in your network obtain their IP addresses from the DHCP server on the NetScreen device, then the computers also obtain their default gateway from the NetScreen device. If a computer has a statically assigned IP address, then you must manually set its default gateway to the IP address of the Trust interface on the NetScreen device.To assign a different IP address and netmask to the Trust interface, refer to the “Interfaces” chapter in the “Fundamentals” volume of the NetScreen Concepts & Examples ScreenOS Reference Guide for ScreenOS 5.0.0.To change the DHCP settings for the NetScreen device, refer to the “System Parameters” chapter in the “Fundamentals” volume of the NetScreen Concepts & Examples ScreenOS Reference Guide for ScreenOS 5.0.0.VERIFYING EXTERNAL CONNECTIVITYTo verify that workstations in your network can access resources on the Internet, start a Web browser from any workstation in the network and enter the following URL: www.juniper.net.RESETTING THE DEVICE TO FACTORY DEFAULTSIf you lose the admin password, you can reset the NetScreen device to its default settings. This destroys any existing configurations, but restores access to the device.You can restore the device to its default settings in one of the following ways:•Using a Console connection. For further information, see the “Administration” chapter in the “Administration” volume of the NetScreen Concepts & Examples ScreenOS Reference Guide for ScreenOS 5.0.0.•Using the reset pinhole on the rear panel of the device, as described in the next section.Warning: Resetting the device deletes all existing configuration settings and renders existing firewall and VPN service inoperative.

Chapter 2 Configuring the Device30 User’s GuideUsing the Reset PinholeYou can reset the device and restore the factory default settings by pressing the reset pinhole. To perform this operation, you need to either view the device status LEDs on the front panel or have a Console session as described in “Using a Console Connection” on page 15.1. Locate the reset pinhole on the rear panel. Using a thin, firm wire (such as a paper clip), push the pinhole for four to six seconds and then release.The Status LED blinks amber. A message on the Console states that erasure of the configuration has started and the system sends an SNMP/SYSLOG alert.2. Wait for one to two seconds.After the first reset, the Status LED blinks green; the device is now waiting for the second reset. The Console message now states that the device is waiting for a second confirmation.3. Push the reset pinhole again for four to six seconds.The Console message verifies the second confirmation. The Status LED lights amber for one-half second and then returns to the blinking green state. The device then resets to its original factory settings. When the device resets, the Status LED turns amber for one-half second and then glows green. The Console displays device bootup messages. The system generates SNMP and SYSLOG alerts to configured SYSLOG or SNMP trap hosts.After the device has rebooted, the Console displays the login prompt for the device. The status LED now blinks green.If you do not follow the complete sequence, the reset process cancels without any configuration change and the console message states that the erasure of the configuration is aborted. The Status LED returns to blinking green. If the device did not reset, an SNMP alert is sent to confirm the failure.Reset Pinhole

NetScreen-5GT Wireless 313Chapter 3Hardware DescriptionsThis chapter provides detailed descriptions of the NetScreen-5GT Wireless chassis.PORT AND POWER CONNECTORSThe rear panel of the NetScreen-5GT Wireless device contains port and power connectors.Antenna B Antenna A

Chapter 3 Hardware Descriptions32 User’s GuideThe DC power receptacle is for connecting power to the NetScreen-5GT Wireless. The Reset pinhole allows you to reset the device and restore its factory default settings. The NetScreen-5GT Wireless device includes the following ports:STATUS LEDSThe front panel of the NetScreen-5GT Wireless device has power and status LEDs for the device and port status LEDs for the interfaces.Port Description Connector Speed/ProtocolADSL When applicable, enables an Internet connection through an ADSL data link. RJ-11 (Annex A)RJ-45 (Annex B) ANSI T1.413 Issue 2ITU G.992.1 (G.dmt)ITU 992.2 (G.lite)Console Enables a serial connection with the system. Used for launching Command Line Interface (CLI) sessions.RJ-45 9600 bps/RS-232Modem Enables a dial backup serial Internet connection through an external modem. RJ-45 9600 bps-115 Kbps/RS-232Untrusted Enables a primary or backup Internet or untrusted network connection through an external router, DSL modem, or cable modem.RJ-45 10/100 Mbps/EthernetAutosensing duplex and polarityPorts 1-4 Enables direct connections to workstations or a LAN connection through a switch or hub. This connection also allows you to manage the device through a Telnet session or the WebUI management application.RJ-45 10/100 Mbps/EthernetAutosensing duplex and polarityAntenna A & B Enables direct connection to workstations in vicinity of a wireless radio connection.This connection allows you to manage the device through a Telnet session or the WebUI management application.RPSMA 802.11b 802.11gWarning: Do not connect a phone line or ISDN line directly to the Modem port on the NetScreen-5GT Wireless device. You must first connect the device to a modem, using an RS-232 port, and then connect the modem to the line.

Status LEDsNetScreen-5GT Wireless 33Main Status LEDs for the DeviceThe device status LEDs indicate whether the device is operating properly. The following table describes the status for each LED.Port Status LEDsThe port status LEDs indicate whether the ports on the device are operating properly. The following table describes the possible status for the ports.LED Status Meaning POWER green Indicates the system is receiving power.off Indicates the system is not receiving power.STATUS blinking green Indicates the system is functioning.green Indicates the system is starting up.red Indicates a diagnostics or system initialization error.off Indicates the system is not operational.ADSL (on the Wireless ADSL only)green Indicates the ADSL loop is up.off Indicates the ADSL loop is down.WLAN slow blinking green Indicates that a Wireless connection is established, but there is no link activity.fast blinking green Indicates that a Wireless connection is established. The blink rate is proportional to the link activity.off Indicates there is no Wireless connection established.LED LED Color Meaning of the LEDLink/Activity blinking green Indicates the device detects Ethernet traffic for the port. off Indicates the port has not established a link with another device.green Indicates the port has established a link with another device.10/100 green Indicates the port is connected to a 100 Base-T device.off Indicates the port is connected to a 10 Base-T device.

Chapter 3 Hardware Descriptions34 User’s Guide

NetScreen-5GT Wireless 35AAppendix ASpecificationsThis appendix provides general system specifications for the NetScreen-5GT Wireless device.AttributesHeight 2.93 centimeters 1.15 inchesDepth 18.45 centimeters 7.26 inchesWidth 20.8 centimeters 8.19 inchesWeight .9 kilograms 1.98 poundsElectricalSwitching Regulator AC voltage: 100-240 VAC+/- 10% 50/60 HzAC Watts: 12 WattsDC voltage: 12 VoltsEnvironmentalNormal altitude 0°-40° C, 32-105°FRelative humidity 10-90%Non-condensing 10-90%The maximum normal altitude is 3,657.6 meters (12,000 feet)CertificationsSafety UL, CUL, CE, CB, A-TickEMI FCC Part 15 class B, VCCIEthernet ConnectorsStandard 100Base-TXMedia Type Category 5 and higher Unshielded Twisted Pair (UTP) CableMaximum Distance 100 meters (328.08 feet)The RJ-45 twisted-pair ports are compatible with the IEEE 802.3 Type 10/100 Base-T standardADSL ConnectorTypes 6-pin RJ-11 connector for Annex ARJ-45 connector for Annex BMedia Type Standard telephone cable

Appendix A Specifications36 User’s GuideCONSOLE AND MODEM ADAPTER CONNECTIONSThe following table lists the RJ-45 connector definitions. To employ a standard UART port, both the console and the modem ports use this configuration.The table below lists the RJ-45 to DB-9 adapter connection definitions. To employ a standard UART port, both the console and the modem ports must use this configuration.RJ-45 Signal Abbreviation DCE1Request To Send RTS In2Data Terminal Ready DTR In3Transmitted Data TD In4, 5 Signal Ground SGND N/A6Received Data RD Out7Not Connected8Clear To Send CTS OutDB9 Signal Abbreviation DTE DCE RJ451Data Carrier Detect DCD In Out NC2Received Data RD In Out 33Transmitted Data TD Out In 64Data Terminal Ready DTR Out In 75Signal Ground SGND N/A N/A 46Data Set Ready DSR In Out 27Request To Send RTS Out In 88Clear To Send CTS In Out 19Ring Indicator RI In Out NCNote: If you use the Console cable that is provided with the NetScreen device to connect to a modem, then you need to obtain and install a null modem adapter on the modem connector.

NetScreen-5GT Wireless IX-37AAAL5 multiplexing 20adding virtual circuit 20address of Trust zone interface 29admin name, changing 16ADSLconfiguring interface 20connecting the cable 7connecting the port 7Annex A 7Annex B 7configuring for Deutsch Telecom 22ATM Adaptation Layer 5 20Bbackup interface to Untrust zone 28Cchanging login name and password 16changing the port mode 26configurationdefault settings 19optional 24required 15, 19connecting power 10connectors 31Console, using 15conventionsWebUI 4Ddate, setting 16default settings 19restoring 29Deutsch Telecom, configuring Annex B 22GGuide Organization 3LLEDsport status 33Status 32LLC encapsulation 20Logical Link Control encapsulation 20Mmanaging device from specific host 25microfilter 8mounting device in rack 10multiplexingconfiguring 21NNetScreen Publications 5Ppasswordchanging 16Point-to-Point Protocol over ATMSee PPPoAPoint-to-Point Protocol over EthernetSee PPPoEpolicies, configuring additional 25port connectors 31port mode, changing 26port status LEDs 33power connectors 31power, connecting 10PPPoA 20configuring 22PPPoE 20configuring 22Rrack mounting the device 10registering the device 13reset device to default settings 29reset pinhole, using 30restoring default settings 29restricting management from specific host 25Route mode 25Ssetting device clock 16signal splitter 8splitter, signal 8

IX-38 User’s Guidestatic IP address 20configuring 23status LEDs 32TTelnet, using 14time, setting 16Transparent mode 25Trust zoneconfiguring interface address 29UUntrust zone, configuring backup interface 28VVC multiplexing 20verifying connectivity 29Virtual Channel multiplexing 20virtual circuit, adding 20Virtual Path Identifier/Virtual Channel IdentifierSee VPI/VCIVPI/VCI 20configuring 21WWebUI, conventions 4WebUI, using 13

Navigation menu