Johnson Controls KONOZ KONOz Smart Hub Thermostat User Manual

LUX Products Corporation KONOz Smart Hub Thermostat

Contents

User Manual

Installaon ManualSmart Hub THERMOSTAT™
Thank you for inving KONOz™ into your home. The setup process is easy. All you need to do is follow these simple steps and you’ll be on your way to saving energy and making your home even more comfortable.LUX Products oers installaon and product videosPlease visit LuxProducts.com/videos or visit our YouTube channel LUX Products Corporaon.Note: To contact LUX Technical Support, please call 856.234.8803.Para ver estas instrucciones en español, por favor visite. LuxProducts.com/KONOzmanualSP
LuxProducts.com | 31. START HERETools NeededTable of Contents1. Start Here ......................................................................................2-52. Installing KONOz ..........................................................................6-103. Operang KONOz ......................................................................11-164. Appendix....................................................................................17-19KONOzDrill Oponal: Wire Stripper Smart HubPhillips ScrewdriverBaeriesWhat’s in the box?Screws Wall AnchorsTrim Plate Wiring Labels
4 | 856.234.8803This manual is a comprehensive guide for the installaon and wiring of your KONOz thermostat.Step 1.1: Turn o the power at the circuit breaker to both your heang and cooling systems before performing any wiring. Step 1.2: Conrm that your heang and cooling system is powered down by changing the temperature on your exisng thermostat. The heang and cooling should not come on but may show the temperature change on your exisng thermostat. Note: Your system should not make any noise and you should not feel any air exing your vents.Step 1.3: Remove the front of your old thermostat from its base. If you see thick black wires, wire nuts, or any labels that say 120-240VAC or High Voltage, your system is not compable with KONOz . Please call LUX Technical Support at 856.234.8803 before proceeding with your installaon. If you do not see any high voltage labels or wires, you may connue with the installaon process.HIGHVOLTAGESTOP
LuxProducts.com | 5Step 1.4: Take a picture of your current wiring layout. The picture can be used as reference later.Step 1.5: Use the included wire labels to mark which wire is connected to each terminal in your old thermostat.Note: Wiring leer designaons correspond to either a “Heat Pump” or “Convenonal” system.Note: A wiring compatability tool is available at LuxProducts.com/wiring1. START HERE
6 | 856.234.8803WiringStep 2.1: Idenfy your system conguraon (see wiring diagrams in appendix). Potenal conguraons include:System Conguraon Wiring ConguraonConvenonal: 1H/1C without C-wire Y, G, W1, RConvenonal: 1H/1C with C-wire Y, G, W1, R, CConvenonal: 2H/1C without C-wire Y, G, W1, W2, RConvenonal: 2H/1C with C-wire Y, G, W1, W2, R, CSystem Conguraon Wiring ConguraonHeat Pump: 1H/1C with C-wire Y, G, R, O/B, CHeat Pump with auxiliary or dual fuel: Y, G, R, O/B, W1, CIf you have only one R wire, please use the RH terminal. If you have a dierent conguraon other than what is listed above, please call LUX Technical Support for help with your installaon. If you have a “C” wire then the included baeries are not needed.Note: If you do not have a C-wire but would rather not use replaceable baeries, please visit shop.LuxProducts.com/PowerBridge to learn more about our Lux Power Bridge soluon.
LuxProducts.com | 7Step 2.2: Verify that each wire has been properly labeled and remove each wire from its terminal — make sure that they don’t fall into the wall. Step 2.3: Remove the mounng screws from the base of the old thermostat and remove the base from the wall.Step 2.4: Separate KONOz from its base.Step 2.5: If you would like to use the trim plate or wall anchors, you may install them now.Step 2.6: Pull the wires from your wall through the center hole of the KONOz base. Secure the base to the wall using the included mounng hardware. Follow the built in level to ensure that it is straight.INSTALLATION 2. WIRINGStep 2.4Step 2.5 Step 2.6
8 | 856.234.8803Opon 1 - Convenonal (furnace) Systems:Step 2.7f: Follow the terminal labels marked “Convenonal” on the thermostat base. Press the lever and insert each labeled wire into the top hole of the corresponding terminal.Step 2.8f: If you have both an RC and RH wire present, then remove the red cap next to the reset buon. You can now proceed to step 2.9.Opon 2 - Heat Pump Systems:Step 2.7hp: Follow the terminal labels marked “Heat Pump” on the thermostat base. Referencing your wiring photo, press the lever and insert each labeled wire into the top hole of the corresponding terminal. If your old thermostat did not have a W1 wire but did have a W2 wire, insert the W2 wire into the W1 terminal.Step 2.8hp: If you have both an O wire and a B wire (i.e. in a Trane system), install the B wire in the “C” terminal. For more detailed direcons, please see the wiring diagrams in the appendix or call LUX Technical Support.CONVENTIONAL C Y1 W2 HEAT PUMP C Y1 O/B POWER BRIDGE 4 CONVENTIONAL C Y1 W2 HEAT PUMP C Y1 O/B POWER BRIDGE 4
LuxProducts.com | 9 WiringStep 2.9: If you do not have a C-wire, insert the (4) AA baeries included with your KONOz thermostat according to their correct polarizaon markings found on the KONOz.Securely fasten KONOz onto its base. Once it has clicked into place, return power to your heang and cooling system.Note: If baeries are installed, you must replace all baeries with only premium brand alkaline baeries at least once every two years. To replace the baeries, remove the KONOz from it’s base (ie disconnecng it from its supply mains) and insert (4) AA premium brand alkaline baeries. If you discover leaky or damaged baeries, do not touch the baeries. Leaky or damaged baeries must be handled with proper safety equipment included safety glasses with side shields, and neoprene or natural rubber gloves in a well-venlated room. For disposal of baeries, abide by the local laws and regulaons of your region. If you are not able to idenfy the applicable rules in your area, please check the instrucons of the baery manufacturer. For disposal of KONOz, you must remove baeries prior to disposal. INSTALLATION 2. WIRING
10 | 856.234.8803Step 2.11: Aer conrming your system sengs, KONOzwill ask if you would like to connect to a Smart Hub. Select “SET”to establish a connecon with your Smart Hub or select “OFF” to connect later. For details on how to congure KONOz for your parcular Smart Hub please visit: LuxProducts.com/KONOzSmartHubSetup(F) for Furnace or Boiler:Set the fan type to Gas (most common), Electric (for systems without gas or oil), or Boiler (no fan).(HP) for Heat Pump:Set the valve type to O or B - look at the photo of your wiring to see your valve type.First you will need to set your system type:Step 2.10: Your KONOz is now ready to be congured for your heang and cooling system. The KONOz will guide you through the inial system conguraon. Use the knob to change opons and press the knob to conrm your selecon.
LuxProducts.com | 11Changing KONOz’s Décor-snap™ CoverPlace right hang on outside edge of the Décor-snap cover and le hang on the edge of the KONOz screen. Hold KONOz in place while gently pulling the decor snap cover. You will nd important informaon for Smart Hub setup including the Zigbee Install Code and model number.*Note: Run Schedule will only work if enabled on Smart Hub.Press the knob when the thermostat is idle to view the menu. Rotate the knob to select an opon and press again to conrm. Press the knob when the thermostat is idle to view the menu. Rotate the knob to select an opon and press again to conrm.System Mode Installaon SengsFan Mode Network ConneconRun Schedule System PreparingFor more informaon about installaon sengs, please visit LuxProducts.com/KONOmanualOPERATIONS GUIDE 3. OPERATIONSSmart Hub*
12 | 856.234.8803The operaons guide secon covers the following:• 3.1 How to use KONOz• 3.2 Reading KONOz’s screen• 3.3 Using KONOz throughout the year3.1 How to use KONOzKONOz’s knob is the main way for you to control your heang and cooling systems. Simply press the knob to open a menu or select an opon. Press and hold the knob at any me to exit a menu and return to the home screen. In a menu, rotate the knob to cycle through available opons.Note: If you are interested in advanced informaon, the Installaon Seng Guide can be found at LuxProducts.com/KONOzManual
LuxProducts.com | 133.2 Reading KONOz’s screenThe large number in the top le shows your ambient room temperature.The small number in the boom right shows your set temperature.The selected system mode (HEAT, COOL or OFF) is shown to the right of the ambient room temperature.The acve fan status is shown by the icon below the ambient room temperature. If it is o, your fan is not running. If it is on, your fan is running. Please note that your fan will run depending on your selected fan mode (either AUTO or ON).If you see ON under your system mode, it means that your system is acvely heang or cooling your home. This icon indicates the baery levels of the KONOz.Note: Replace all four AA baeries in the KONOz if the low baery icon or blinking empty baery icon appears on your KONOz.OPERATIONS GUIDE 3. OPERATIONSThis icon shows that your HVAC system is preparing to turn on or o. Please wait for heang and cooling to start.
14 | 856.234.8803Reading KONOz’s screenThis icon opens the system mode menu. In this menu, you can set your HVAC system to OFF, HEAT, or COOL. Your thermostat will automacally detect which modes are available when you install your thermostat, so you may not see all three opons depending on your system type.This icon opens the fan mode menu. In this menu, you can set your fan to AUTO, or ON. AUTO will run your fan when your system is acvely heang or cooling. ON will run your fan connuously. If you set a lter life value in the installaon sengs, you’ll be able to check the remaining life of your lter in the fan sengs menu.This icon opens the installaon sengs menu. In this menu, you can adjust advanced preferences for special applicaons. Select the gear icon, then aer IS appears on the screen, select YES to begin the installaon sengs ow. For more informaon about the installaon sengs, please view the “Installaon Sengs Guide”.
LuxProducts.com | 15This icon opens the Smart Hub network connecon menu. In this menu, you can choose to connect or disconnect from your Smart Hub. Select “SET” to establish a new Smart Hub connecon. Select “OFF” to temporarily disable the connecon. Lastly, select “ON” to reconnect to your Smart Hub. For more informaon about connecng to a Smart Hub, please view KONOz’s Smart Hub Setup Guide. 3.3 Using KONOz throughout the yearCold Weather:Heat mode is the best seng to use when it’s cold out and you won’t need to use your air condioner. This will make sure that your air condioner stays idle and that your heater keeps your home’s temperature above your chosen set-temperature.Hot Weather:Cool mode is the best seng to use when it’s hot out and you won’t need to use your heang system. This will make sure that your heater stays idle and that your air condioner keeps your home’s temperature below your chosen set-temperature.OPERATIONS GUIDE 3. OPERATIONS
16 | 856.234.8803Congratulaons!Installaon is complete and your KONOz is ready to go. Now let’s save some energy and make your home more comfortable.Personalize your KONOz.It’s more than a thermostat, it’s décor! Match KONOz to your style by simply changing the Décor-snap cover. Check out our wide variety of designer colors and nishes at LuxProducts.com/ShopCovers Hibiscus Red Sea Green Deep Blue TrueWhiteMidnight BlackSky Blue Sea Mist Grey Champagne Gold PaintItDriwood
LuxProducts.com | 17Convenonal SystemNotes:• C-wire oponal• The W2 terminal is used for 2 stage heang• If you have both an RH and RC wire, please remove the red cap from the back of the thermostat4. APPENDIXRCRCGG1CC4Y1Y1W2O/BW1W12RHRH3ConventionalHeat PumpPower BridgeConventionalHeat PumpPower BridgeFurnace ThermostatFanHeat (Stage 1)Heat (Stage 2)CoolTransformer
18 | 856.234.8803Heat Pump SystemNotes:• C-wire oponal• The W1 terminal is used for Auxiliary/Emergency heat or on Dual Fuel systemsRCRCGG1CC4Y1Y1W2O/BW1W12RHRH3ConventionalHeat PumpPower BridgeConventionalHeat PumpPower BridgeFanAUX/Emer HeatChangeover ValveCompressorTransformerHeat Pump Thermostat
LuxProducts.com | 194. APPENDIXTechnical Informaon:Disconnecon Means: Type 1BPolluon Degree: 2Impulse Voltage: 330VAutomac Acon: 100,000 cyclesElectrical Rang:-Input: 24V a.c. 60Hz or 4xAA Alkaline baery-Output: @24V a.c. Max. 1.5AFCC Part 15CWarning: Changes or modicaons to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons.However, there is no guarantee that interference will not occur in a parcular installaon.If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separaon between the equipment and receiver.• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operaon. FCC RF Radiaon Exposure StatementCauon: To maintain compliance with the FCC’s RF exposure guidelines, place the unit at least 20cm from nearby persons.RSS-247This device complies with Industry Canada licence-exempt RSS standard(s). Operaon is subject to the following two condions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operaon of the device.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitaon est autorisée aux deux condions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’ulisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est suscepble d’en compromere le fonconnement.
LUX PRODUCTS CORPORATION Philadelphia, PA 19112 USA LuxProducts.com Designed in Philadelphia.53620

Navigation menu