Johnson Controls KONO3 LUX KONO Smart Thermostat User Manual

LUX Products Corporation LUX KONO Smart Thermostat

User Manual

Installaon ManualSmart THERMOSTAT
Thanks for inving KONOTM into your home. The setup process is easy. All you need to do is follow these simple steps and you’ll be on your way to saving energy and making your home even more comfortable.LUX Products oers installaon and product videosPlease visit LuxProducts.com/videos or visit our YouTube channel LUX Products Corporaon. To contact LUX Technical Support please call 856.234.8803.Para ver estas instrucciones en español, por favor visite LuxProducts.com/KONOmanualsSP[Drill]
LuxProducts.com | 3Tools NeededTable of Contents1. Start Here ......................................................................................2-62. Installing with a C-Wire................................................................7-103. Installing without a C-Wire ........................................................11-144. Connecng to the Network .......................................................15-195. Appendix....................................................................................20-23KONO SmartDrill Oponal: Wire Stripper SmartphonePhillips Screwdriver1. START HERELUX Power BridgeTMWiring LabelsWhat’s in the box?Screws Wall AnchorsTrim Plate
4 | 856.234.8803Behind KONO’s Décor-snapTM cover you will see a small, removable “quick guide” to installaon and an icon-key label. The icons represent the display icons of your KONO Smart. You will also nd important informaon for HomeKitTM and WiFi setup.This manual is a comprehensive guide to installaon and wiring.Press the knob when the thermostat is idle to view the menu. Rotate the knob to select an opon and press again to conrm.System Mode Installaon SengsFan Mode Network ConneconRun Schedule System PreparingFor more informaon about installaon sengs, please visit LuxProducts.com/KONOmanual
LuxProducts.com | 5Step 1.1: Download the LUX Products App to your mobile device and create an account. Step 1.2: Now set your phone aside and turn o the power at the circuit breaker to both your heang and cooling systems before performing any wiring.Step 1.3: Conrm that your heang and cooling system is powered down by changing the temperature on your thermostat. Hint: Your system should not make any noise and you should not feel any air exing your vents. Step 1.4: Remove the front of your old thermostat from its base. If you see thick black wires, wire nuts, or any labels that say 120-240VAC or High Voltage, your system is not compable with KONO Smart. Please call LUX Technical Support at 856.234.8803 before proceeding with your installaon. If you do not see any high voltage labels or wires, you can connue with your installaon.1. START HEREHIGHVOLTAGE
6 | 856.234.8803Step 1.5: Use the included wire labels to mark which wire is connected to each terminal in your old thermostat. Take a picture of your current wiring layout – it may be helpful to reference this picture later.Step 1.6: Conrm if you have a C-Wire. If you do, please turn to the next page. If you do not, please skip ahead to page 11.
LuxProducts.com | 7INSTALLATION WITH C-WIRE2. Installing with a C-wireBefore starngTurn o the power at the circuit breaker to both your heang and cooling systems before performing any wiring. You will not need the included LUX Power Bridge.STOP
8 | 856.234.8803Installaon with C-wireStep 2.1: Idenfy your system conguraon (see wiring diagrams in appendix). Potenal conguraons include:• Convenonal 1H/1C (Y, G, W, R, C)• Convenonal 2H/1C (Y, G, W, W2, R, C)• Heat Pump Single-Stage (Y, G, R, O/B, C)• Heat Pump with auxiliary heat or dual fuel (Y, G, R, O/B, W, C)If you have only one R wire, please use the RH terminal. If you have a dierent conguraon other than what is listed above, please call LUX Technical Support for help with your installaon.Step 2.2: Remove each wire from its terminal – make sure that they don’t fall down back into the wall. Step 2.3: Remove the mounng screws from the base of the old thermostat. Remove the base from the wall. Step 2.4: If you would like to use the trim plate or wall anchors, you can install them now.Step 2.5: Separate KONO Smart from its base. Pull the wires from your wall through the center hole of the KONO Smart base. Secure the base to the wall using the included mounng hardware.
LuxProducts.com | 9Opon 1 - Convenonal (furnace) Systems:Step 2.6f: Following the terminal labels marked “Convenonal” on the thermostat base, press the lever and insert each labeled wire into the top hole of the corresponding terminal.Step 2.7f: If you have both an RC and RH wire present, then remove the red cap next to the reset buon. You can now skip ahead to step 2.8.Opon 2 - Heat Pump Systems:Step 2.6hp: Following the terminal labels marked “Heat Pump” on the thermostat base and referencing your wiring photo, press the lever and insert each labeled wire into the top hole of the corresponding terminal. If your old thermostat did not have a W1 wire but did have a W2 wire, please insert the W2 wire into the W1 terminal.Step 2.7hp: If you have both an O wire and a B wire (i.e. in a Trane system), please install the B wire to the “C” terminal. For more detailed direcons, please see the wiring diagrams in the appendix or call LUX Technical Support.INSTALLATION WITH C-WIRE2. CONVENTIONAL C W1 W2HEAT PUMP C W1 OBPOWER BRIDGE 1 4 2 CONVENTIONAL C W1 W2HEAT PUMP C W1 OBPOWER BRIDGE 1 4 2
10 | 856.234.8803Installaon with C-wireStep 2.8: Securely fasten KONO Smart onto its base. Once it has clicked into place, return power to your heang and cooling system.Step 2.9: Aer your thermostat powers up, you are ready to congure KONO Smart for your heang and cooling system and connect to a wireless network. Please skip ahead to the “Connecng to the Network” secon of this manual on page 15.
LuxProducts.com | 11Installing without a C-Wire Using the Included LUX Power BridgeFor installaon without C-wire, you will need to access your furnace.Before starngTurn o the power at the circuit breaker to both your heang and cooling systems before performing any wiring.STOPINSTALLATION WITHOUT C-WIRE3. 1. Install and wire your KONO 2. Install LUX Power Bridge at your furnace
12 | 856.234.8803Installaon without C-wireHint: helpful videos showing how to wire a thermostat with the LUX Power Bridge are available at LuxProducts.com/videosStep 3.1: Starng at your thermostat, conrm that you have one of the system conguraons listed below:• Convenonal 1H/1C (Y, G, W, R)• Convenonal 2H/1C (Y, G, W1, W2, R)If you have a dierent conguraon other than what is listed above, please call LUX Technical Support for help with your installaon.Step 3.2: Remove each wire from its terminal – make sure that they do not fall down back into the wall. Step 3.3: Remove the mounng screws from the base of the old thermostat. Remove the base from the wall. Step 3.4: If you would like to use the trim plate or wall anchors, you can install them now.
LuxProducts.com | 13Step 3.5: Separate KONO Smart from its base. Pull the wires from your wall through the center hole of the KONO Smart base. Secure the base to the wall using the included mounng hardware. Step 3.6: Following the terminal labels marked “Power Bridge” on the thermostat base, press the lever and insert each labeled wire into the top hole of the corresponding terminal. Connect as follows:• Y Wire  Terminal 1• W Wire  Terminal 2• R Wire  Terminal 3• G Wire  Terminal 4Step 3.7: Securely fasten KONO Smart onto its base.Step 3.8: Go to your furnace – remove the door or panel and locate your control board or transformer. In most cases, there should be four wires running from the furnace to your thermostat – Y, G, W, and R. If you have addional wires, leave them as is. INSTALLATION WITHOUT C-WIRE3. CONVENTIONAL C W1 W2HEAT PUMP C W1 OBPOWER BRIDGE 1 4 2
14 | 856.234.8803Step 3.9: i) Matching the leers, label the wires connected to your furnace with the included white Power Bridge wire labels. Take a picture of the wiring at your control board. ii) Disconnect these wires from the control board. iii) Open the Power Bridge and insert each of your old wires into the corresponding numbered terminals in the Power Bridge. iv) Finally, insert the Power Bridge wires (with the colored labels) into the corresponding terminals on your furnace control board.Step 3.10: Secure the LUX Power Bridge to your furnace. If you had to remove a panel or door to access your control panel, replace it now.Step 3.11: Return power to your heang and cooling system. If your system, including your thermostat, does not power up please call LUX Technical Support. Aer KONO Smart powers up, you are ready to congure it for your heang and cooling system and connect to a wireless network. i) ii) iii) iv)Y G W R C1(Y)Y G W R C1(Y)4(G)2(W)3(R)Y G W R C1(Y)4(G)2(W)3(R)C4(G)Y G W R C1(Y)Y G W R C1(Y)4(G)2(W)3(R)Y G W R C1(Y)4(G)2(W)3(R)C4(G)1(Y)4(G)1(Y)4(G)2(W)3(R)C3(R)2(W)Y G W R C1(Y)Y G W R C1(Y)4(G)2(W)3(R)Y G W R C1(Y)4(G)2(W)3(R)C4(G)Furnace Furnace Furnace
LuxProducts.com | 15Connecng to the Network Step 4.1: Aer your thermostat powers up, it will guide you through the inial system conguraon. Use the knob to change opons and press the knob to conrm your selecon.First you will need to set your system type(F) for Furnace or Boiler (HP) for Heat Pumpthen thenSet the fan type to Gas (most common), Electric (for systems without gas or oil), or Boiler (no fan)Set the valve type to O or B – look at the photo of your wiring to see which you haveNote: For advanced sengs please visit LuxProducts.com/KONOmanual or call LUX Technical Support.Step 4.2: Aer conrming your system sengs, KONO Smart will ask if you would like to connect to the network. Select “ON” to begin connecon or “OFF” to connect later. If you wish to connect, please make sure that you have downloaded the LUX Products App to your smartphone and created an account. Hint: If you are having trouble, please see our instruconal video atLuxProducts.com/videosCONNECTING TO THE NETWORK4.
16 | 856.234.8803Press the knob when the thermostat is idle to view the menu. Rotate the knob to select an System ModeFan Mode Network Run Schedule System Preparing LuxProducts.com/KONOmanualCOOLON HomeKitCodeAndroid WiFi CodeStep 4.3: Aer selecng “ON”, KONO Smart will display “01”. You will then need to select “iOS” if you are using an Apple® device or “And” if you are using an Android® device. Step 4.4: Aer selecng “iOS” or “And”, your thermostat will display a large “02”, then “03”. Remove your Décor-snapTM cover. 2 / 2SCALE 1:1FILE: KONO3_ART03A_HOMEKIT_LABELP/N: N/AMODEL: KONO3PAGE: DRAW BY: Dickson Lo / 26 May 2017APPROVED BY: Joyce Lee / 26 May 2017TITLE: HOMEKIT LABELDIMENSIONS IN MM. GENERAL TOLERANCES: LINEAR: +/- 0.2100.0 mm2D QR-CODE format rules:1. Format: DDMMYYXXXXXX. 2. 1th to 6th digits are the date code, where YY is year, MM is month and DD is day. e.g. 9th Mar. 2015, YY=15(year), MM=03(month), DD=09(day)3. 7th to 12th digits are the serial number in numeric characters. The serial number should be reset to 000001 for every different date code. e.g. XXXXXX=0 000014. KONO3 and D DMMYYV should be put underneat h the 2D QR-CODE, where YY is year, MM is month, DD is day and V is the version of the product which refers to ID_CO DE2 in SAP BOM. e.g. 9th Mar. 2015, version of product is A; i.e. DDMMYYV=090315A; (The QR-CODE Inform ation (Both QR code & Text including “K ONO3” & “DDMMYYV”) MUST same as t he QR-CODE Label on the PCB)Font and fon t size is Arial 5pt. 123-45-678WIFI Name: KONO3260517AExample: (For Reference only)WIFI Password: LUX KONO-1a-2412345678KONO3DDMMYYVExampleQR-CODE INFORMATION
LuxProducts.com | 17iOS® (iPhone® or iPad®) Open your LUX App, tap the + icon to add a new accessory, then select the accessory ID that starts with LUX KONO to start the connecon process. Follow the instrucons in the App.If you need to cancel the joining process at any me, simply press and hold the knob for 5 seconds.Locate your accessory’s HomeKit Code under the Décor-snap cover. When prompted, use your iPhone or iPad’s camera to scan the code.Aer the App scans the code, your App and thermostat will handle the remaining steps in the connecon process.CONNECTING TO THE NETWORK4. When you see the thermostat’s idle screen, it means you are connected. You can now replace the Décor-snap cover.To control this HomeKit-enabled accessory, iOS 10.3 or later is recommended.COOLON
18 | 856.234.8803ANDROID®Open your LUX App, tap the + icon to add a new thermostat. When prompted by the LUX App, please use your phone’s WiFi sengs to join your LUX KONO’s WiFi network. The network name and password can be found under the Décor-snap cover.Aer connecng your thermostat to the network, please return to the App and select your home WiFi network from the list and enter your password.Please make sure your phone reconnects to your home WiFi network and then return to the LUX App. From this point your thermostat and App will handle the remaining steps in the connecon process.When you see the thermostat’s home screen, it means you are connected. You can now replace the Décor-snap cover.COOLON
LuxProducts.com | 19Congratulaons!Installaon is complete and your KONO is ready to go. Now let’s save some energy and make your home more comfortable.Personalize your KONO Smart.It’s more than a thermostat, it’s décor! Match KONO to your style by simply changing the Décor-snap cover. Check out our wide variety of designer colors and nishes at LUXProducts.com/shopcovers. Hibiscus Red Sea Green Deep Blue WoodGrainMidnight BlackCONNECTING TO THE NETWORK4.
20 | 856.234.8803Convenonal System With C-Wire Wiring DiagramTransformerConvenonalHeat PumpPower BridgeHEAT (STAGE 1)HEAT (STAGE 2)FANCOOLCW1W2GY1RCRHCW1O/BGY1RCRH4123FurnaceThermostatNotes:• The W2 terminal is used for 2 stage heang systems only• If you have both an RH and RC wire, please remove the red cap from the back of the thermostat
LuxProducts.com | 21Heat Pump System With C-Wire Wiring Diagram APPENDIX5. TransformerConvenonalHeat PumpPower BridgeAUX / EMER HeatCHANGEOVER VALVEFANCOOLCW1W2GY1RCRHCW1O/BGY1RCRH4123Heat PumpThermostatNotes:• The W1 terminal is used for Auxiliary/Emergency heat or on Dual Fuel systems
22 | 856.234.8803LUX Power Bridge Wiring DiagramCOOLConvenonalHeat PumpPower BridgeFurnaceThermostatFANHEAT (STG 1)TRANSFORMERCOMMONHEAT STG2LUX Power BridgeCW1W2GY1RCRHCW1O/BGY1RCRH4123YGWRC12341(Y)2(W)3(R)4(G)Notes:• If you have a heat pump or dual transformer system, please call LUX Tech support.• If you have any wires on your furnace not shown here, please leave them as is.
LuxProducts.com | 23Apple HomeKit™Use of the Works with Apple HomeKit logo means that an electronic accessory has been designed to connect regulatory standards.Apple is a trademark of Apple Inc., registered in the U.S. and other countries. HomeKit is a trademark of Apple Inc.Industry Canada Regulatory Informaon Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. APPENDIX5. FCC Part 15Ccould void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to following measures:• Reorient or relocate the receiving antenna.• Consult the dealer or an experienced radio/TV technician for help.
LUX PRODUCTS CORPORATION Philadelphia, PA 19112 USA LuxProducts.com Designed in Philadelphia.54066

Navigation menu