JVCKENWOOD 452701 UHF Digital Transceiver User Manual NX 740H NX 740HV NX 840H NX 840HU

JVC KENWOOD Corporation UHF Digital Transceiver NX 740H NX 740HV NX 840H NX 840HU

Contents

User Manual

VHF DIGITAL TRANSCEIVERNX-740H NX-740HVUHF DIGITAL TRANSCEIVERNX-840H NX-840HUINSTRUCTION MANUAL© B5A-0031-10 (K)
iOne or more of the following statements may be applicable:FCC WARNINGThis equipment generates or uses radio frequency energy. Changes or modifi cations to this equipment may cause harmful interference unless the modifi cations are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modifi cation is made.INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCCThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer for technical assistance.THANK YOUWe are grateful you have chosen KENWOOD for your personal mobile applications.This instruction manual covers only the basic operations of your mobile radio. Ask your dealer for information on any customized features they may have added to your radio.NOTICES TO THE USER◆ Government law prohibits the operation of unlicensed transmitters within the territories under government control.◆ Illegal operation is punishable by fi ne and/or imprisonment.◆ Refer service to qualifi ed technicians only.SAFETY: It is important that the operator is aware of, and understands, hazards common to the operation of any transceiver.◆ EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.) Turn OFF your transceiver while taking on fuel or while parked in gasoline service stations. Do not carry spare fuel containers in the trunk of your vehicle if your transceiver is mounted in the trunk area.◆ INJURY FROM RADIO FREQUENCY TRANSMISSIONS Do not operate your transceiver when somebody is either standing near to or touching the antenna, to avoid the possibility of radio frequency burns or related physical injury.◆ DYNAMITE BLASTING CAPS Operating the transceiver within 500 feet (150 m) of dynamite blasting caps may cause them to explode. Turn OFF your transceiver when in an area where blasting is in progress, or where “TURN OFF TWO-WAY RADIO” signs have been posted. If you are transporting blasting caps in your vehicle, make sure they are carried in a closed metal box with a padded interior. Do not transmit while the caps are being placed into or removed from the container.
iiCONTENTSGETTING STARTED .................................................................................................1GETTING ACQUAINTED ..........................................................................................3PROGRAMMABLE FUNCTIONS .............................................................................6BASIC OPERATIONS ...............................................................................................6NXDN ........................................................................................................................ 8SCAN ........................................................................................................................8DTMF CALLS ...........................................................................................................9SIGNALING ............................................................................................................10FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION ....................................11ADVANCED OPERATIONS ....................................................................................12BACKGROUND OPERATIONS ..............................................................................14PRECAUTIONSObserve the following precautions to prevent fi re, personal injury, and transceiver damage.• Do not attempt to confi gure the transceiver while driving; it is too dangerous.• Do not disassemble or modify the transceiver for any reason.• Do not expose the transceiver to long periods of direct sunlight, nor place it near heating appliances.• If an abnormal odor or smoke is detected coming from the transceiver, switch the transceiver power off immediately, and contact your KENWOOD dealer.• Use of the transceiver while you are driving may be against traffi c laws. Please check and observe the vehicle regulations in your area.• Do not use options not specifi ed by KENWOOD.◆ The transceiver operates in 12 V negative ground systems only! Check the battery polarity and voltage of the vehicle before installing the transceiver.◆ Use only the supplied DC power cable or a KENWOOD optional DC power cable.◆ Do not cut and/or remove the fuse holder on the DC power cable. For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set so the transceiver will not break loose in the event of a collision.
1GETTING STARTEDNote: The following instructions are for use by your KENWOOD dealer, an authorized KENWOOD service facility, or the factory.SUPPLIED ACCESSORIESCarefully unpack the transceiver. We recommend that you identify the items listed below before discarding the packing material. If any items are missing or have been damaged during shipment, fi le a claim with the carrier immediately.DC power cable (with fuses). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1• 15 A fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Mounting Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Screw set• 5 x 16 mm self-tapping screw. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4• M4 x 8 mm Hex-headed screw with washer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4• Spring washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4• Flat washer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Microphone (with cable)• KMC-30 (NX-740H/ NX-840H) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1• KMC-35 (NX-740HV/ NX-840HU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Microphone hanger (with 4 x 16 mm self-tapping screws) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Instruction manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1PREPARATIONVarious electronic equipment in your vehicle may malfunction if they are not properly protected from the radio frequency energy which is present while transmitting. Typical examples include electronic fuel injection, anti-skid braking, and cruise control. If your vehicle contains such equipment, consult the dealer for the make of vehicle and enlist his/her aid in determining if they will perform normally while transmitting.■ Power Cable ConnectionThe transceiver operates in 12 V negative ground systems only! Check the battery polarity and voltage of the vehicle before installing the transceiver.1 Check for an existing hole, conveniently located in the fi rewall, where the power cable can be passed through.• If no hole exists, use a circle cutter to drill a hole, then install a rubber grommet.2 Run the power cable through the fi rewall and into the engine compartment.3 Connect the red lead to the positive (+) battery terminal and the black lead to the negative (–) battery terminal.• Place the fuse as close to the battery as possible.4 Coil the surplus cable and secure it with a retaining band.• Be sure to leave enough slack in the cables so the transceiver can be removed for servicing while keeping the power applied.
2M4 x 8 mm Hex-headed screwDC power cableMounting bracketAntenna connectorPower input connectorFuseBlack (–) cableRed (+) cable12 V vehicle batteryMicrophone5 x 16 mmSelf-tapping screwSpring washerFlat washer■ Installing the TransceiverFor passenger safety, install the transceiver securely using the supplied mounting bracket and screw set, so the transceiver will not break loose in the event of a collision.Note: Before installing the transceiver, check how far the mounting screws will extend below the surface. When drilling mounting holes, be careful not to damage vehicle wiring or parts.1 Mark the position of the holes in the dash, using the mounting bracket as a template. Using a 4.2 mm (5/32 inch) drill bit, drill the holes, then attach the mounting bracket using the supplied screws.• Mount the transceiver within easy reach of the user and where there is suffi cient space at the rear of the transceiver for cable connections.2 Connect the antenna and the supplied power cable to the transceiver.3 Slide the transceiver into the mounting bracket and secure it using the supplied hex-headed screws.4 Mount the microphone hanger in a location where it will be within easy reach of the user.• The microphone and microphone cable should be mounted in a place where they will not interfere with the safe operation of the vehicle.When replacing the fuse in the DC power cable, be sure to replace it with a fuse of the same value. Never replace a fuse with one that is rated with a higher value.
3GETTING ACQUAINTED (Power) switchPress to switch the transceiver ON or OFF. / keysPress to activate their programmable functions {page 6}. DisplayRefer to page 4. / keysPress to activate their programmable functions {page 6}. TX/RX IndicatorLights red while transmitting. Lights green while receiving a signal. Flashes orange when receiving an optional signaling call. Microphone jackInsert the microphone plug into this jack. Status IndicatorLights during a specifi ed mode, based on dealer programming. (Such as AUX, External Speaker, Horn Alert, Lone Worker, Priority Zone-Channel Select, Public Address, Scan Delete/Add, Scrambler/Encryption and Talk Around.) S / A / <B / C> / keysPress to activate their programmable functions {page 6}. SpeakerInternal speaker. PTT switchPress this switch, then speak into the microphone to call a station. Antenna connectorConnect the antenna to this connector. ACC connectorConnect the ACC to this connector, via the KCT-60. External speaker jackConnect an external speaker to this jack. Power input connectorConnect the DC Power Cable to this connector.FRONT/ REAR PANELACC.
4DISPLAYThe display shows the zone/ channel number and the 2 dots show various modes of operation.Display Description PageZone Display (Zone 1) 7Zone Display (Zone 2) 7Channel Display (Channel 16) 7Appears during Site Roaming. (ro)-Appears when switch the transceiver ON.The Transceiver Password function is programmed. (PS) 6Appears during Scan. (Sc) 8The selected channel is the Priority channel. (P) 9Appears when a channel is added to the scan list. (cA) 9Appears when a channel is removed from the scan list. (cd) 9Appears when the Autodial mode is on. (Ad) 9Autodial list Display (Autodial list 1) 9Appears when the Redialing mode is on. (rd) 9Appears during the transceiver is stunned. (St) 10
5• AUX• External Speaker• Horn Alert• Lone Worker• Priority Zone-Channel• Public Address• Scan Delete/Add• Scrambler/Encryption• Talk AroundThe right dot will blink during special operations, as listed below. Display Description PageAppears when the Operator Selectable Tone mode is on. (ot) 11Appears when the Lone Worker function is on. (Ln) 12Appears when the Talk Around function is on. (tA) 12Appears when the Scrambler function is on. (Sr) 12Appears when the Encryption function is on. (Ec) 12Appears when the Scrambler/ Encryption code mode is on. (co) 12Appears when the Squelch Level setting is on. (SL) 13Appears when the Public Address function is on. (PA) 13Appears when the Horn Alert function is on. (HA) 13Appears when the AUX function is on. (AU) 14The left and right dots on the display can be programmed to indicate specifi c modes of operation, as listed below.• Autodial• Operator Selectable Tone• Channel Entry• Scrambler/Encryption Code• Squelch Level
6BASIC OPERATIONSSWITCHING POWER ON/ OFFPress to switch the transceiver ON.• A beep sounds and the display illuminates.• If the Transceiver Password function is programmed, “PS” will appear on the display when the power is turned ON. Refer to “Transceiver Password”, below.Press again to switch the transceiver OFF.PROGRAMMABLE FUNCTIONSThe , , , , S, A, <B, C>, and keys can be programmed with the functions listed below. Ask your dealer for details on these functions.• None• Autodial 1• AUX• Call 1/ Call 2• Channel Down• Channel Entry• Channel Up• CW Message 2• Direct Zone-Channel• Emergency 3• External Speaker• Horn Alert• LED Brightness• Lone Worker• Monitor• Monitor Momentary• Paging Call• Priority Zone-Channel Select• Squelch Off 1• Squelch Off Momentary 1• Operator Selectable Tone 1• Public Address• Scan• Scan Delete/Add• Scrambler/Encryption• Scrambler/Encryption Code• Send the GPS Data• Squelch Level 1• Talk Around• Volume Down• Volume Up• Zone Down• Zone Up1 Available only for Analog operation.2 Available only for NXDN operation.3 Emergency can be programmed only on the key.
7■ Transceiver Password To enter the password:1 Press / to select a digit.• When using an optional microphone with a keypad, simply enter the password digits and proceed to step 3.2 Press C> to accept the entered digit and move to the next digit.• Press A or # to delete an incorrect digit. Press and hold A or # to delete all digits.• Repeat steps 1 and 2 to enter the entire password.3 Press S or to confi rm the password.• If you enter an incorrect password, the transceiver remains locked.ADJUSTING THE VOLUMEPress the [Volume Up] key to increase the volume. Press the [Volume Down] key to decrease the volume.If Squelch Off has been programmed onto a key, you can use that function to listen to background noise while adjusting the volume level.SELECTING A ZONE AND CHANNELSelect the desired zone and channel using the keys programmed as [Zone Up]/[Zone Down] and [Channel Up]/ [Channel Down].• “G1” (Zone 1)/ “16” (Channel 16) appears on the display.TRANSMITTING1 Select your desired zone and channel.2 Press the key programmed as [Monitor] or [Squelch Off] to check whether or not the channel is free.• If the channel is busy, wait until it becomes free.3 Press the PTT switch and speak into the microphone to transmit. Release the PTT switch to receive.• For best sound quality at the receiving station, hold the microphone approximately 1.5 inches (3 cm ~ 4 cm) from your mouth.RECEIVINGSelect the desired zone and channel. If signaling has been programmed on the selected channel, you will hear a call only if the received signal matches your transceiver settings.Note: Signaling allows your transceiver to code your calls. This will prevent you from listening to unwanted calls. Refer to “SIGNALING” on page 10 for details.
8NXDNNXDN is a general term for the NXDN wireless communication protocol which uses 4 Level FSK. Various data communications, including individual and group voice communications, Status calls, and GPS data transmission, are possible.INDIVIDUAL/ GROUP CALLSEach channel is set up with an individual or group ID list number. To make a call, select the channel with the ID list number you wish to call, then press the PTT switch to start the call.• Your dealer may also have set Selcall on PTT for Individual or Group calls, allowing you to make an Individual or Group call when pressing the PTT switch.• To page the target transceiver instead of initiating a voice call, press the key programmed as [Paging Call].• If PTT Proceed tone is enabled, the Proceed tone will sound. After the tone ends, you can begin the call.■ Receiving When you receive an individual call, a ringing tone will sound. Respond to the call by pressing the PTT switch.• If the auto reset timer expires before you respond to the call, the call will end. Your dealer can set the duration for the auto reset timer (default is 10 seconds). When you receive a group call and the received group ID matches the ID set up on your transceiver, a ringing tone will sound and you can hear the caller’s voice.STATUS CALLYou can transmit your status (preset by your dealer) to the target transceiver by pressing the key programmed as [Call 1] or [Call 2], if they have been set up with an NXDN Status.• Select the desired channel before sending the status call.SCANScan monitors for signals on the transceiver channels. While scanning, the transceiver checks for a signal on each channel and only stops if a matching signal is present.To start/ stop scanning, press the key programmed as [Scan].• “Sc” appears on the display during Scan.• When a signal is detected, Scan pauses at that channel. The transceiver will remain on the busy channel until the signal is no longer present, at which time Scan resumes. Note: To use Scan, there must be at least 2 channels added to the scanning sequence.
9PRIORITY SCANIf a Priority channel has been programmed, the transceiver will automatically change to the Priority channel when a call is received on that channel, even if call is being received on a normal channel.• “P” appears on the display to indicate the Priority channel (depending on dealer setting).TEMPORARY CHANNEL LOCKOUTDuring scan, you can temporarily remove specifi c channels from the scanning sequence by pressing the key programmed as [Scan Delete/Add] while Scan is paused at the undesired channel. • The channel is no longer scanned. However, when scanning is ended and restarted, the Scan settings return to normal.SCAN DELETE/ ADDYou can add and remove channels to and from your scan list.1 Select your desired channel.2 Press the key programmed as [Scan Delete/Add] to remove a channel.• When a channel is added to scan, “cA” appears on the display. When it is removed, “cd” appears on the display.DTMF CALLSNote: For keypad operation, you must use an optional microphone with a keypad.MANUAL DIALING1 Press and hold the PTT switch.2 Enter the desired digits using the keypad.• If Keypad Auto-PTT is enabled by your dealer, you do not need to press the PTT switch to transmit; you can make the call simply by pressing the keys.AUTODIALAutodial allows you to quickly call DTMF numbers that have been programmed onto your transceiver.1 Press the key programmed as [Autodial] or the key.• “Ad” appears on the display.2 Press <B and C> to select your desired Autodial list number, or enter the list number directly (1 ~ 9).• “A1” (Autodial list 1) appears on the display.3 Press the PTT switch to make the call.REDIALING1 Press the key programmed as [Autodial] or the key.• “Ad” appears on the display.2 Press the 0 key.• “rd” appears on the display.• If there is no data in the redial memory, an error tone will sound.3 Press the PTT switch to make the call.Note: Switching the transceiver power OFF clears the redial memory.
10STUNThis function is used when a transceiver is stolen or lost. When the transceiver receives a call containing a stun code, the transceiver becomes disabled. The stun code is canceled when the transceiver receives a call with a revive code.• “St” appears on the display while the transceiver is stunned.SIGNALINGQUIET TALK (QT)/ DIGITAL QUIET TALK (DQT)The Encoder/ Decoder function uses QT/ DQT to segregate talk groups, so users only hear calls from their own group.RADIO ACCESS NUMBER (RAN)RAN is a signaling system designed for digital radio communications. When a channel is set up with a RAN, squelch will only open when a call containing a matching RAN is received. If a call containing a different RAN is made on the channel you are using, you will not hear the call. This allows you to ignore (not hear) calls from other parties who are using the same channel.NXDN IDNXDN ID is an optional signaling system available only for digital communications.DTMFA DTMF PTT ID is included for dispatch operations or simple remote control applications. The DTMF decode capabilities include Selective Call ID, Transpond with ID, and “Wild Card” Group Calling.2-TONE2-tone Signaling opens the squelch only when your transceiver receives a call containing matching 2 tones.FleetSyncRefer to “SELCALL (SELECTIVE CALLING)” on page 11.MDC-1200The following features are available with the built-in MDC signaling: PTT ID Encode, Emergency Encode, Stun/ Revive Decode, and Radio Check Decode.Note: The transceiver cannot decode MDC-1200 if the FleetSync baud rate is 2400 bps.
11FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTIONFleetSync is an Alphanumeric 2-way Paging Function and is a protocol owned by JVC KENWOOD Corporation.Note: If set up by your dealer, your transceiver may use the MDC-1200 feature in place of FleetSync. MDC-1200 and FleetSync cannot be operated simultaneously.SELCALL (SELECTIVE CALLING)A Selcall is a voice call to a particular station or to a group of stations.■ Transmitting1 Select your desired zone and channel.2 Press the PTT switch to transmit your PTT ID list and begin your conversation.■ Receiving If enabled by your dealer, an alert tone will sound and the LED will blink when a Selcall has been received. To respond to the call, press the PTT switch and speak into the microphone.■ Identifi cation Codes An ID code is a combination of a 3-digit Fleet number and a 4-digit ID number. Each transceiver must have its own Fleet and ID number.Note: The ID range may be limited by programming.PAGING CALL1 Select your desired zone and channel.2 Press and hold the key programmed as [Paging Call] for 1 second to transmit your PTT ID list, to request a call.GPS REPORTIf a GPS unit (NMEA-0183 format) is installed on your transceiver, you can press the key programmed as [Send the GPS data] to send your location data.OPERATOR SELECTABLE TONE (OST)You can change the preset encode and decode tones for the selected channel. Up to 16 OST pairs can be pre-programmed by your dealer.1 Select your desired channel.2 Press the key programmed as [Operator Selectable Tone] or press and hold the key.• “ot” appears on the display, followed by the current OST number.3 Press <B and C> to select the desired OST number.4 Use the transceiver the same as in a regular call; press the PTT switch to transmit and release it to receive.5 To exit OST mode and return to the preset encode and decode tones, press S.
12ADVANCED OPERATIONSEMERGENCY CALLSIf your transceiver has been programmed with the Emergency function, you can make emergency calls.1 Press and hold the key programmed as [Emergency].• Depending on the delay time programmed into your transceiver, the length of time you must hold the [Emergency] key will vary.• When the transceiver enters Emergency mode, the transceiver will change to the Emergency channel and begin transmitting based on how the transceiver is set up.2 To exit Emergency mode, press and hold the [Emergency] key again.• If the Emergency mode completes the preset number of cycles, Emergency mode will automatically end and the transceiver will return to normal.■ Lone Worker Mode Lone Worker Mode is a safety feature built into the transceiver. If the transceiver is not operated for a pre-programmed period of time, the transceiver will emit a tone and automatically enter Emergency operation. Press the key programmed as [Lone Worker] to toggle the Lone Worker function ON or OFF.• “Ln” appears on the display for 1 second.TALK AROUNDDuring interruptions in service (such as a power failure), you can continue to communicate by using the Talk Around feature. Talk Around allows you to communicate directly with other transceivers without the use of a repeater, as long they are not too far away or there are no geographical obstacles in the way.Press the key programmed as [Talk Around] to toggle the Talk Around function ON or OFF.• “tA” appears on the display for 1 second.SCRAMBLER/ ENCRYPTIONThe Scrambler (analog) and Encryption (NXDN) function allows you to hold a conversation in complete privacy. When activated, any other party listening in on your channel will be unable to understand your conversation. Press this key to toggle the Scrambler/ Encryption function ON or OFF.Press the key programmed as [Scrambler/Encryption] to toggle the Scrambler/ Encryption function ON or OFF.• “Sr”(analog)/ ”Ec”(NXDN) appears on the display for 1 second.You can change the scrambler/ encryption codes:
131 Press and hold the key programmed as [Scrambler/Encryption code] for 1 second.• “co” (code) appears on the display, followed by the current scrambler/ encryption code.2 Press <B and C> to select your desired scrambler/ encryption code.3 Press S or to store the new setting.• After changing your scrambler/ encryption code, be sure to inform all of your group members of the new code so they can also reset their transceivers. The scrambler/ encryption function will not work with transceivers set up with different scrambler/ encryption codes.MONITOR/ SQUELCH OFFYou can use the key programmed as [Monitor] or [Squelch Off] to listen to weak signals that you cannot hear during normal operation and to adjust the volume when no signals are present on your selected channel.Your dealer can program a key with one of 4 functions:• Monitor: Press to deactivate QT, DQT, DTMF, FleetSync Signaling, or NXDN. Press again to return to normal operation.• Monitor Momentary: Press and hold to deactivate QT, DQT, DTMF, FleetSync Signaling, or NXDN. Release to return to normal operation.• Squelch Off: Press to hear background noise. Press again to return to normal operation.• Squelch Off Momentary: Press and hold to hear background noise. Release to return to normal operation.■ Squelch Level If a key has been programmed as [Squelch Level], you can readjust your transceiver’s squelch level:1 Press the key programmed as [Squelch Level].• “SL” appears on the display, followed by the current squelch level.2 Press <B and C> to select the desired squelch level from 0 to 9.3 Press S or to store the new setting.PUBLIC ADDRESS (PA)The PA system can only be used with an optional relay unit and external speaker.1 Press the key programmed as [Public Address] to activate the Public Address function.• “PA” appears on the display for 1 second.2 Press and hold the PTT switch, then speak into the microphone to make your address through the external speaker.3 Press the [Public Address] key again to exit Public Address.HORN ALERTThe Horn Alert function can only be used with an optional relay unit. Press the key programmed as [Horn Alert] to toggle the Horn Alert function ON or OFF.• “HA” appears on the display for 1 second.
14BACKGROUND OPERATIONSTIME-OUT TIMER (TOT) The Time-out Timer is used to prevent you from using a channel for an extended duration. If you continuously transmit for a preset time, the transceiver will stop transmitting and a warning tone will sound. Release the PTT switch to stop the tone.AUXILIARY PORTPress the key programmed as [AUX] to activate the auxiliary port. The auxiliary port is used with optional boards.• “AU” appears on the display for 1 second.DISPLAY BRIGHTNESSYou can cycle the display brightness between high, low, and off by pressing the key programmed as [LED Brightness].DIRECT ZONE CHANNELPress the key programmed as [Direct Zone-Channel] to immediately select the lowest channel of the lowest zone.BUSY CHANNEL LOCKOUT (BCL)When activated, BCL prevents you from interfering on a channel that is already in use. Pressing the PTT switch will cause a warning tone to sound and the transceiver will not transmit. Release the PTT switch to stop the tone.Note: Ask your dealer for an explanation on how BCL functions when using QT, DQT, RAN, or Optional signaling.If BCL Override has been programmed, you can transmit over the current signal:1 Press and hold the PTT switch.• If the channel is already in use, a warning tone will sound.2 Quickly release and then press the PTT switch again.3 Speak into the transceiver as you would during a normal call.PTT IDPTT ID is the transceiver unique ID code which is sent each time the PTT switch is pressed and/or released.Note: PTT ID can be made only in analog operation.COMPANDERIf programmed by your dealer for a channel, the compander will remove excessive noise from transmitted signals, to provide higher clarity of signals.Note: The compander is used only in analog operation.VOICE ANNOUNCEMENTWhen changing the zone/ channel, an audio voice will announce the new zone/ channel number.
MANDATORY SAFETY INSTRUCTIONS TO INSTALLERS AND USERS• Use only manufacturer or dealer supplied antennas.• Antenna Minimum Safe Distance: 40 cm (16 inches), 50% duty Cycle.• Antenna Gain: 0 dBd referenced to a dipole.The Federal Communications Commission has adopted a safety standard for human exposure to RF (Radio Frequency) energy which is below the OSHA (Occupational Safety and Health Act) limits.• Antenna Mounting: The antenna supplied by the manufacturer or radio dealer must not be mounted at a location such that during radio transmission, any person or persons can come closer than the above indicated minimum safe distance to the antenna, i.e. 40 cm (16 inches) , 50% duty Cycle.• To comply with current FCC RF Exposure limits, the antenna must be installed at or exceeding the minimum safe distance shown above, and in accordance with the requirements of the antenna manufacturer or supplier.• Vehicle installation: The antenna can be mounted at the center of a vehicle metal roof or trunk lid, if the minimum safe distance is observed.• Base Station Installation: The antenna should be fixed-mounted on an outdoor permanent structure. RF Exposure compliance must be addressed at the time of installation.Antenna substitution: Do not substitute any antenna for the one supplied or recommended by the manufacturer or radio dealer.You may be exposing person or persons to excess radio frequency radiation. You may contact your radio dealer or the manufacturer for further instructions.Maintain a separation distance from the antenna to person(s) of at least 40 cm (16 inches), 50% duty Cycle. “This transmitter is authorized to operate with a maximum duty factor of 50%, in typical push-to-talk mode, for satisfying FCC RF exposure compliance requirements.”You, as the qualified end-user of this radio device must control the exposure conditions of bystanders to ensure the minimum separation distance (above) is maintained between the antenna and nearby persons for satisfying RF Exposure compliance. The operation of this transmitter must satisfy the requirements of Occupational/Controlled Exposure Environment, for work-related use, transmit only when person(s) are at least the minimum distance from the properly installed, externally mounted antenna. Transmit only when people outside the vehicle are at least the recommended minimum lateral distance away from the antenna/vehicle.B59-2723-00

Navigation menu