JETOP ICB284 Bluetooth Speaker with Clock User Manual

JETOP INDUSTRIAL LIMITED Bluetooth Speaker with Clock

User manual

Any Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Snooze/DimmerPress to snooze the alarm after it sounds. Press and hold to dim the brightness of the LED display. Press to set the Sleep Timer.Bluetooth Speaker with ClockUser’s Guide for Model ICB284S v982-01FUNCTIONS AND CONTROLSVolume +/- /AL1/AL2Press to adjust the volume, or to set Alarm 1 or Alarm 2.TUN +/-Press to tune the radio, or set the time for the clock/alarm.PowerPress to power the radio on or o. Mem/ClockWith the Radio on, press it and TUN +/- to cycle through preset radio stations. In o mode, press and hold to adjust the clock. While paired to a Bluetooth device, press to play or pause media from the speaker.LED DisplaySource Press to switch between Radio, Line In, and BluetoothPair Press to pair Bluetooth devices to the unit.BluetoothIndicator LightsAlarm 1SpeakerRemovable Back StandAlarm 2PMAdditional Warnings • The apparatus shall not be exposed to dripping or splashing and that no objects lled with liquids, such as vases, shall be placed on apparatus.• Do not place the unit on top of any soft, porous, or sensitive surfaces to avoid damaging the surface. Use a protective barrier between the unit and surface to protect the surface.• Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.• If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.• Do not mix old and new batteries.• Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries.• Batteries should be recycled or disposed of as per state and local guidelines.RF Warnings The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. FCC CautionThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
AAAAAABattery Backup The battery backup is intended for short power outages only. The clock radio’s primary functions cannot run o of the battery backup alone. Requires 2, AAA-size, batteries (not included).Bottom ViewRear ViewPower Plug the AC/DC power adapter (included) into the DC Power Input on the unit, and a standard power outlet. The unit can be used to charge mobile devices through a USB charging port in the rear, as seen on the below (USB cable not included).DC Power InputUSB Charging PortLine In
Setting the Clock1. With the unit o, press and hold the MEM/CLK button until the display begins ashing.2. Press the TUN ± buttons to adjust the time in hours. The PM indicator will light when the hour is set in the PM.3. While the display is still ashing, press MEM/CLK again to switch to minutes, then press the TUN ± buttons to set the time in minutes.4. Press MEM/CLK to nish, or wait for the display to stop ashing.Saving a Station as a Preset1. With the radio on, tune to your desired frequency, press and hold the MEM/CLK button until the screen ashes.2. Press the TUN ± buttons to choose the desired preset station, 1 though 20. 3. Press MEM/CLK again to set the frequency to that preset station.4. Once set, press MEM/CLK to select your presets (Pxx will apear on the display), then press the TUN ± buttons to cycle through your preset stations.CLOCKRADIOLINE IN AND BLUETOOTHRadio ReceptionAn FM antenna is built into the clock radio. To improve FM radio reception, adjust the position of the clock radio.Tuning the FM Radio1. Power on the radio by pressing the Power button.2. Press the Source button to select radio mode, then press the TUN ± buttons to nd the desired radio frequency.3. Press the VOL ± buttons to adjust the volume of the radio.Line InAn auxiliary line in port is built into the rear of the unit and can be used to play media directly from a mobile device using a 3.5mm audio cable (not included). To do this, simply plug the cable into the Line In port on the unit and on your device. Press the Source button to select AU on the display, and your music should be heard through the speaker. Pairing a Bluetooth Device Refer to the user’s manual for your specic device for instructions on pairing and connecting Bluetooth devices. When pairing, the device should remain within 3 feet of the speakers. 1. Press the Source button to select bt on the display. A blue light above the display will also indicate this. 2. Press the PAIR button. The blue light will begin to ash quickly. 3. Using the native controls on your Bluetooth device, scan for and select ICB284 in your Bluetooth settings to pair.4. If your device requests a password, enter 0 0 0 0.5. When successfully paired, the indicator will stop ashing and remain solid.6. After initial pairing, the unit will stay paired unless unpaired manually by the user, or erased due to a reset of the device.7. If any pairing issues should occur, un-pair the unit on your Bluetooth device and follow the above steps again.
Setting Alarm 1/Alarm 21. With the radio o, press and hold the AL1 or AL2 buttons until the display begins ashing. Note the white indicator light above the display.2. Press the TUN ± buttons to select bb (buzzer) or Fr7 (radio) on the display.3. Press AL1 or AL2 to set.4. Press the TUN ± buttons to adjust the time in hours. The PM indicator will light when the hour is set in the PM.5. While the display is still ashing, press AL1 or AL2 again to switch to minutes, then press the TUN ± buttons to set the time in minutes.6. Press the AL1 or AL2 buttons again to nish, or wait for the display to stop ashingSetting the Sleep Timer1. While powered on, press the Snooze/Sleep/Dimmer button repeatedly to set the sleep timer ( 90, 80, 70, 60, 50, 40, 30, 20, 10 min, or O ).2. Once the set sleep time has expired the clock radio will automatically power o.ALARMSLEEP TIMERSnooze and Alarm ResetAfter the alarm sounds: Press the Snooze button to delay the alarm for an additional 9 minutes, OR Press the Power button to turn the alarm o until the set alarm time is reached again.Cancelling the AlarmPress the AL1 or AL2 button until the indicator is no longer lit.To download this User’s Guide in English, Spanish, or French, or to get answers to frequently asked questions, visit the support section at: www.iLiveElectronics.comPour télécharger ce guide de l’utilisateur en anglais, espagnol ou français, ou pour obtenir des réponses à des questions fréquemment posées, consultez la rubrique d’assistance sur: www.iLiveElectronics.comPara descargar este Manual del Usuario en inglés, español y francés, o para obtener respuestas a preguntas frecuentes, visite la sección de apoyo en: www.iLiveElectronics.comINTERNATIONAL SUPPORTFor Warranty Information and the most up-to-date version of this User’s Guide, go to www.iLiveElectronics.comCustomer Service: 1-888-999-4215 | Email Support: prodinfo@dpiinc.com | Email Parts: partsinfo@dpiinc.comCopyright © 2013 Digital Products International (DPI, Inc.) All other trademarks appearing herein are the property of their respective owners. Specications are subject to change without notice.

Navigation menu