Iton Technology MW1601-5P Wi-Fi MODULE User Manual 15 MW1601 5P UserMan P2

Iton Technology Corp. Wi-Fi MODULE 15 MW1601 5P UserMan P2

Contents

15_MW1601-5P UserMan_P2.pdf

Our Focus , Your Legend 802.11 b/g/n single chipIton Technology Corp www.sziton.com8Storage Temperature -40℃~125℃Antenna externalOperation System windows XP32/64,Vista 32/64, Win7 32/64, Linux, MacOperation Voltage 3.3V DC6. Size Of Module Graph6.1 Physical Map
Our Focus , Your Legend 802.11 b/g/n single chipIton Technology Corp www.sziton.com96.2 Machine Size Map And Pin DefinitionPin DefinitionPin Name Description1 VCC 3.3V2 DP USB D+ signal3 DM USB D- signal4 GND Ground5 NC No connect7.Process ParametersTBD
Our Focus , Your Legend 802.11 b/g/n single chipIton Technology Corp www.sziton.com108.Packaging InformationPacking information :blister + vacuum bagThe module into the blister caseBlister (5*10) Vacuum bagCartonsThe blister packedmodule and desiccantinto the vacuum bagA good vacuum sealedvacuum bag in turn intocartons
InstallationGuideFinishedAssemblyMasterPCB(examples)2. Ready the Master PCB which will connect with MW1601-5P Module. Check connection pads is clean forsoldering.Place the Module on the Master PCB with SMT. 1.CheckMW1601‐5PModuleconnectionpiniscleanforsoldering.9.Application
4. Connect DC Power 3.3V on VCC and GND on Master PCB.Connect to Antenna by antenna connector. Antennaconnector3. After soldering,Check all pads are well connected. NOTE:The antenna gain should no more than 0 dBi.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.
Attention:LimitedModularApproval‐thisRFModulemaynotbesoldtothegenericpublicandrequiresprofessionalinstallation.DuetothefactthatthisRFModuleisnotequippedwithanownshielding,theend‐productincl.thisRFModulehastoshowcompliancetotheFCCrules(15C/radiatedemissions).(OEM)Integratorhastoassurecomplianceoftheentireend‐productincl.theintegratedRFModule.Additionalmeasurements(15C)and/orequipmentauthorizations(e.gmayneedtobeaddresseddependingonco‐locationorsimultaenoustransmissionissuesifapplicable.Integratorisremindedtoassurethattheseinstallationinstructionswillnotbemadeavailabletotheend‐userofthefinalhostdevice.   integratedintoany(portable,mobile,fixed)hostdevice.Thefinalhostdevice,intowhichthisRFModuleisintegrated"hastobelabelledwithanauxilliarylablestatingtheFCCIDoftheRFModule,suchas"ContainsFCCID: Dependingonthesizeofthefinalend‐product,the§15.19FCCstatement"Thisdevicecomplieswithpart15oftheFCCrules.Operationissubjecttothefollowingtwoconditions:(1)thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation."shouldbeplacedalsoonthedeviceoralternativelywithinaprominentlocationoftheusersmanualThe§15.21"Changes or modifications to this unit not expresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser’sauthoritytooperatetheequipment."statementhastobeincludedinaprominentlocationoftheusersmanual".)either a complete new certification or a Class II Permissive Change. the Integrator will be responsible to satisfy SAR/ RF Exposure requirements,when the moduleVYVMW1601-5P

Navigation menu