Intermec Technologies RFID915PCC-6 RF IDENTIFICATION PC CARD User Manual 010416M1

Intermec Technologies Corporation RF IDENTIFICATION PC CARD 010416M1

appendix m User Info DoC 6110 hand held terminal

Intermec Technologies Corporation REPORT NO: 010416-1EMC Test Laboratory DATE: April 16, 2001DOC. NO.: 577-500-980 Page 1 of 1915 PC Card Radio Module, FCC 15.247, Canada RSS-210, RSS-102 FCC ID: EHARFID915PCC-6APPENDIX M, 6110 Users Manual and DoC insertTechnologies CorporationEMC Test LaboratoryCedar Rapids, IAMEASUREMENT/TECHNICAL REPORTIntermec Technologies CorporationRF Identification (RFID) 915 PC Card –6915 MHz Spread Spectrum TransmitterREPORT NO: 010416-1DATE: April 16, 2001APPENDIX MDECLARATION OF CONFORMITY INSERT, USER INFORMATIONFOR THE INTERMEC 6110 TERMINAL
578-100-0xx Revision A Page 1 of 1*578-100-0xx* *578-100-0xx*Compliance Statement InsertDevice Name: Hand-held Computer Model Number: 6110The responsible party for the compliance of this device is: Intermec Technologies Corporation6001 36th Avenue WestEverett, WA 98203 USA(425) 348-2600This product conforms to the following approvals. The user(s) of this product are cautioned to use accessories and peripheralsapproved by Intermec Technologies Corporation. The use of accessories other than those recommended or changes to thisproduct that are not approved by Intermec Technologies Corporation may void the compliance of this product and may result inthe loss of the users authority to operate the equipment.FCC Digital Emissions ComplianceThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guaranteethat interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the radio of television receiving antenna.• Increase the separation between the computer equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected.• Consult the dealer or an experienced radio television technician for help. Canadian Digital Apparatus Compliance This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. This device complies with part 15 of the FCC and Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not causeharmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.CAUTION: See users guide instructions for handling, charging, and replacing batteries. Failure to follow those instructions canresult in personal injury, fire, or battery explosion.INTERMEC RFID 915 PC Card Radio Users FCC ID: EHARFID915PCC-6WARNING: per the FCC RF (radio frequency) exposure requirements,(1) Only the antenna supplied and installed with this unit by Intermec Technologies is to be used with this hand held terminal.The product is configured to ensure compliance to FCC RF exposure requirements.(2) The user shall not touch the terminal top (antenna) and is to remain 5-cm (2 of and inches) from the front of the antennawhile the transmitter is in use.INTERMEC RFID 915 PC Card Radio Users Canada ID: xxxxxxxxxxWARNING: per Canada RSS-102, RF (radio frequency) exposure requirements,(1) Only the antenna supplied and installed with this unit by Intermec Technologies is to be used with this hand held terminal.The product is configured to ensure compliance to Canada RF exposure requirements.(2) The user shall not touch the terminal top (antenna) and is to remain 5-cm (2 of and inches) from the front of the antennawhile the transmitter is in use.

Navigation menu