Intermec Technologies RFID915PCC-6 RF IDENTIFICATION PC CARD User Manual 010416L1
Intermec Technologies Corporation RF IDENTIFICATION PC CARD 010416L1
Contents
- 1. appendix l User Info DoC For PC Card
- 2. appendix m User Info DoC 6110 hand held terminal
- 3. Rev B App L PC Card Users Maunal
- 4. Rev B App M 6110 Users Maunal
- 5. Rev C App L Module RFID 915PC Card User Maunal
- 6. Rev C App M 6110 User Maunal
- 7. Users Manual
- 8. User Manual Supplement
- 9. co location user info and compliance statement
- 10. User Info and Compliance Statement
Rev B App L PC Card Users Maunal
![Intermec Technologies Corporation REPORT NO: 010416-1EMC Test Laboratory DATE: April 16, 2001DOC. NO.: 577-500-980 Page 1 of 2915 PC Card Radio Module, FCC 15.247, Canada RSS-210, RSS-102 FCC ID: EHARFID915PCC-6APPENDIX L, 915 PC Card-6 Users Manual and DoC insert, Rev BTechnologies CorporationEMC Test LaboratoryCedar Rapids, IAMEASUREMENT/TECHNICAL REPORTIntermec Technologies CorporationRF Identification (RFID) 915 PC Card –6915 MHz Spread Spectrum TransmitterREPORT NO: 010416-1DATE: April 16, 2001APPENDIX LDECLARATION OF CONFORMITY INSERT, USER INFORMATIONFOR THE 915 PC CARD](https://usermanual.wiki/Intermec-Technologies/RFID915PCC-6.Rev-B-App-L-PC-Card-Users-Maunal/User-Guide-168489-Page-1.png)
![578-100-0xx Revision A Page 1 of 1*578-100-0xx* *578-100-0xx*Compliance Statement InsertDevice Name: RF Identification Radio Module Model Number: 2450 PC Card -5The responsible party for the compliance of this device is: Intermec Technologies Corporation6001 36th Avenue WestEverett, WA 98203 USA(425) 348-2600This product conforms to the following approvals. The user(s) of this product are cautioned to use accessories and peripheralsapproved by Intermec Technologies Corporation. The use of accessories other than those recommended or changes to thisproduct that are not approved by Intermec Technologies Corporation may void the compliance of this product and may result inthe loss of the users authority to operate the equipment.FCC Digital Emissions ComplianceThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:• Reorient or relocate the radio of television receiving antenna.• Increase the separation between the computer equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected.• Consult the dealer or an experienced radio television technician for help. Canadian Digital Apparatus Compliance This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. This device complies with part 15 of the FCC and Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may notcause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.WARNING: RFID 915 PC CardWarning: per the FCC and Canadian RF (radio frequency) exposure requirements,1) Antennas must be supplied and installed as recommended by Intermec Technologies to ensure compliance to RF exposurerequirements. Intermec antenna part number(s) 805-589-001, 805-590-001 and 805-591-001. Correct antenna mounting isfully described within the Intermec RFID 915 PC Card Users Guide.2) When installing and using Intermec approved remote antennas associated the RFID reader, a 4-cm (1.5-inch) passingdistance must be maintained from any body part of the user or near by persons and the remote antenna. The antenna mustnot be touched during transmitter operation.3) Cables attached to the remote antennas must have a minimum length as provided from Intermec to insure the proper lossesto control RF exposure.4) RF safety requirements mandate this device cannot be operated in close proximity to other transmitters.](https://usermanual.wiki/Intermec-Technologies/RFID915PCC-6.Rev-B-App-L-PC-Card-Users-Maunal/User-Guide-168489-Page-2.png)