Intermec Technologies 2106 Access Point, 2106 User Manual 072215QSG1

Intermec Technologies Corporation Access Point, 2106 072215QSG1

Manual

CautionYou must use the appropriate Intermec power supply with this device or equipment damage may occur.ConseilVous devez utiliser la source d’alimentation Intermec adéquate avec cet appareil sinon vous risquez d’endommager l’équipement.CautionGovernment regulatory agencies mandate that the antenna not be alterable. Therefore, the access point uses a custom antenna connector. Do not attempt to use a different antenna or you may damage the connector and the access point.ConseilLes agences responsables de la réglementation gouvernementale exigent que l’antenne ne soit pas modifiable. Par conséquent, le point d’accès est doté d’un connecteur d’antenne personnalisé. Ne pas essayer d’utiliser une antenne différente au risque d’endommager le connecteur et le point d’accès.Quick Start GuideMobileLAN™access 2106More InformationAbout the 2106Safety FirstSpecificationsPhysical 14.66 cm x 9.32 cm x 3.53 cm Operating 0°C to +40°CDimensions (5.77 in x 3.67 in x 1.39 in) Temperature (+32°F to +104°F)  Weight 205 g (0.45 lb) Electrical rating ~100 to 240V   1.0 to 0.5A   50 to 60 Hz For more information on using the 2106, please see:• 21XX Universal Access Point Technical Reference Manual (Part No. 067150)• Intermec Web Site at www.intermec.com  Part No. 072215-001*072215-001* *072215-001*072215-0016001 36th Avenue WestEverett, WA 98203-9280© 2001 Intermec Technologies Corp. All Rights ReservedIntermec’s 2106 access point is a wireless local area network (LAN) product that lets your wireless end devices roam anywhere throughout an enterprise while maintaining a continuous, high-quality network connection. Your 2106 has been certified with an IEEE 802.11a radio. CAUTION!CAUTION!
MobileLAN™access 2106 Quick Start GuidePower After the 2106 boots, this LED remains steadily on.Wired LANThis LED flashes when a frame is transmitted or received on the Ethernet port. Root/errorThis LED flashes if this access point is configured as the root. It remains steadily on if an error has occurred.RadioThis LED flashes when a frame is transmitted or received on the Radio port.1. Install the MobileLAN access Utility by clicking Install Software from the enclosed CD and  following the instructions that appear on your screen. You can also install the software from  www.mobilelan.intermec.com.2. Reboot the access point and configure parameters A through C in the MobileLAN access  Utility main screen.   Note: You must configure parameters A through C within 60 seconds after the  access point has started. In addition, if the access point you are setting is connected   wirelessly, you must have an active radio connection.   Your PC must also be on the same Ethernet segment and subnet as the   access point.113Use this position when storing the 2106.Use this position when the 2106 is mounted on a desktop.Use this position when the 2106 is mounted to a wall.0°90°180°Defining the LEDs, Ports, and Antenna Positions Connecting, Mounting, and Applying Power to the 2106 Setting an Initial IP AddressPlug the AC power cord into an AC power outlet.Plug the power supply into the power port of the 2106.Power SupplyEthernet connectionAEnter the IP address of the access point.BEnter the MAC address of the access point (located on the bottom of the access point).CClick Set AP.Click Configure AP to use the Web browser interface to continue configuring the access point.Powerport10/100 BaseTEthernet portCongratulations!Your 2106 is now ready to begin transmitting data packets between your end devices and your wired network. Mountingscrew (notprovided) (2 places)Screws fasten into mounting surface.Fit the slots on the back of the 2106 over the hooks on the mounting bracket.

Navigation menu