Inseego NVWE362 Cellular/ PCS GSM/ EDGE/ WCDMA/ CDMA and 700 MHz LTE Module User Manual Host 3 of 3

Novatel Wireless Inc Cellular/ PCS GSM/ EDGE/ WCDMA/ CDMA and 700 MHz LTE Module Host 3 of 3

Host user manual 3 of 3

1EnglishWindows 7 Mobile Broadband Quick Start GuideYou can connect to the network using Windows 7 VAN (View Available Network) UI.y Before Starting Mobile Broadband ConnectionI. SIM PurchaseIn order to use your computer to connect to the Internet, you must have a valid GSM or 3G data-enabled SIM Card. SIM Card can be purchased from various telecommunication operators.II. SIM ActivationSIM card must be activated before you can connect to the Internet. Usually, SIM activation is done at the time of purchase. If your SIM was not activated when you purchased it, please contact the appropriate telecom operators for help.III. SIM InsertionPlease insert SIM card before you power on the computer.1 2 3System must be turned off when SIM card is inserted or removed. Otherwise, SIM card will not work correctly.SIM card slot may look differently and location may differ.When you call for SIM activation, you will need to quote two numbers “IMEI” and “ICCID.” “IMEI” number can be found at the bottom of your computer. For “ICCID” number, please refer to purchased SIM.* IMEI label location may vary depending on model.
2y Start Mobile Broadband Connection1 Click on VAN UI icon in the system tray-bar on Windows 7.2 Windows 7 VAN UI is displayed and the available Mobile Broadband Connection is listed like as the following. 3 Click on the connection name and then “Connect” button to connect to the network. ClickClickIf any available connection is not listed in the Mobile Broadband Connection, please check if the SIM card is correctly inserted.
3English4 The network connection is established and Internet access is available.
4y Creating New ProleIf the prole for the inserted SIM card does not exist, you need to create a new prole to connect to the network.1 If the following window is displayed when you click on the connection name and then “Connect” button, you need to create a new prole. 2 Enter the Access point name (if required, User name and Password also) about your service provider.3 Proceed with the next steps.4 Network connection is established and Internet access is available.Enable/Disable Wireless WANFollow instructions below to enable or disable wireless WAN.1. Fn + F12- From keyboard, press Fn + F12 to enable/disable wireless WAN.
y FAQWhy do I keep losing my connection?This may be due to interference caused by other devices like cordless phones, microwave ovens and other 2.4GHz band devices.Why can’t I connect to Internet?You may not be able to establish connection to Internet when you have set incorrect prole. Refer to your SIM card’s service provider and obtain correct APN / User name / Password / PhoneNumber. Then, select proper prole or create a new prole according to the obtained information.Why do I get a slow connection while I am using LTE?LTE is a shared data service. You may experience slower connections when several users in the samearea are accessing the LTE service.I entered the wrong PIN a few times. Why can’t I use my device anymore?If you enter the wrong PIN three times, your SIM card locks automatically. To unlock the card, you must enter a PUK which is provided by service provider at the time of purchase. If you enter the wrong PUK ten times, SIM card will no longer work.I pressed Fn+F12 to enable/disable wireless WAN. Why isn’t wireless WAN turned on/o ?Easy Display Manager should be installed in order to enable/disable wireless WAN. Check ifEasy Display Manager is installed in your system by going to Start > Control Panel and clickingon Uninstall a program. To install Easy Display Manager, go to Start > Samsung > SamsungRecovery Solution to launch Samsung Recovery Solution, select System Software > SystemSoftware Installation to list available software, then look for Easy Display Managers.5

Navigation menu