InnoSenT IPM165F K-Band Transceiver Module User Manual IPM 165 F

InnoSenT GmbH K-Band Transceiver Module IPM 165 F

User manual

Version 7.4 IPM-165 page 1 of 3 2008-04-23 User Manual Product Family: K-Band Transceivers K-Band Transceiver with two integrated patch antennas IPM-165 (and variants IPM-165_UK / IPM-165_F) Description: - radar-based motion detector - available in different frequency ranges: Standard; _F and _UK variants - Standard version selected by signal level - advanced PHEMT-oscillator with low current consumption - split transmit and receive path for maximum gain - mono (single channel) operation - very small outline dimensions Environmental Tests and Handling Precautions: - This InnoSenT Sensor is sensitive to damage from ESD. - Normal precautions as usually applied to CMOS devices are sufficient when handling the device. Touching the signal output pins has to be avoided at any time before soldering or plugging the device into a motherboard. - Applying multimeters e.g. for resistance measurement between any of the connector pins may cause damage to the module. Absolute Maximum Ratings: Parameter Symbol Rating Units supply voltage VCC 5.25 V operating temperature (out of spec) TOP - 40 / + 85 °C storage temperature TSTG + 90 °C Electrical Characteristics: Parameter Symbol min. typ. max. units comment transmit frequency fStandard 24.000 24.125 24.250 GHz fIPM-165_UK 24.150 24.200 24.250 GHz fIPM-165_F 24.075 24.125 24.175 GHz output power (EIRP) Pout 16 dBm temperature drift ∆f - 1 MHz/°C antenna pattern Tx (3dB) horizontal 80 ° azimuth vertical 32 ° elevation side lobe suppression horizontal 13 dB azimuth vertical 13 dB elevation IF output voltage offset -300 300 mV signal level* category A (low) 263 399 mVP-P category B or E (medium) 400 549 mVP-P category C(high) 550 850 mVP-P supply voltage VCC 4.75 5.0 5.25 V supply current ICC 30 40 mA Pulse length tpulse 10 µs operating temperature TOP - 20 + 60 °C outline dimensions ~ 25 x 25 x 7 (12.7) mm compare drawing *Relative output signal level/voltage measured at room temperature in a dedicated InnoSenT test setup.
Version 7.4 IPM-165 page 2 of 3 2008-04-23 Interface: The sensor provides a 2.54mm grid, single row pin header (square pin 0.635mm) Pin # Description In/Out Comment 1 VCC input supply voltage (+5 V) 2 IF1 output signal output 3 GND input analog ground Mechanical Outlines: (all dimensions in mm) Approved pulsing conditions to fulfill the FCC requieremts: • ASK modulation with 10kHz and 10% dutycycle (on-time 10µs min.) • Warning: Any other pulsing condition with less than 10µs on-time may void the FCC authorization to operate this equipment. Certification and environment protection: InnoSenT GmbH has established and applies a quality system for: Development, production and sales of radar sensors for commercial and industrial sensors An audit was performed, Report No. 010350 Proof has been furnished that the requirements according to DIN EN ISO 9001:2000 are fulfilled. This InnoSenT product is compliant to the restriction of hazardous substances (RoHs – European Union directive 2002/95/EG).
Version 7.4 IPM-165 page 3 of 3 2008-04-23 FCC approval • This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • Warning: Changes or modifications made to this equipment not expressly approved by InnoSenT GmbH may void the FCC authorization to operate this equipment. • Manufacturers of mobile or fixed devices incorporating IPM-165 modules are authorized to use the FCC Grants and IC Certificates of the IPM-165 modules for their own final products according to the conditions referenced in these documents. In this case, the FCC label of the module shall be visible from the outside, or the host device shall bear a second label stating "Contains FCC ID: UXS-IPM165F" and "Contains IC: 4012A-IPM165F". Contact Information: InnoSenT GmbH Am Roedertor 30 97499 Donnersdorf Germany Phone: +49 (0) 9528-9518-0 Fax: +49 (0) 9528-9518-99 E-Mail: info@InnoSenT.de Web: www.InnoSenT.de

Navigation menu