InnoComm Mobile Technology SN10-12 SigFox module User Manual rev 4

InnoComm Mobile Technology Corporation SigFox module rev 4

User Manual rev 4.pdf

SN10-12 SIGFOX Module User Manual FCC ID: YAISN10-12 Model Name SN10-12 Project code Description SIGFOX module Version 0.5 Issue Date 2017/05/26 Approved by Reviewed by Issued by Harrison Chen Taka Wei Iestyn Chen
SN10-12 7/12/2017 REV 0.5 InnoComm Mobile Technology Confidential 2/14Revision History Revision Released Date Comments/Remark Author 0.1 2017/03/14 Initial release Iestyn Chen 0.2 2017/03/17 Update with RX performance spec. Iestyn Chen 0.3 2017/03/24 Add module layout guide and appendix section Iestyn Chen 0.4 2017/03/29 Update RX value, reflow profile Iestyn Chen 0.5 2017/05/26 Modify FCC Interference Statement Keller Lin ® 2017 InnoComm Mobile Technology Corp. GENERAL NOTICE THE USE OF THE PRODUCT INCLUDING THE SOFTWARE AND DOCUMENTATION (THE "PRODUCT") IS SUBJECT TO THE RELEASE NOTE PROVIDED TOGETHER WITH THE PRODUCT. IN ANY EVENT THE PROVISIONS OF THE RELEASE NOTE SHALL PREVAIL. THIS DOCUMENT CONTAINS INFORMATION ABOUT INNOCOMM PRODUCTS. THE SPECIFICATIONS IN THIS DOCUMENT ARE SUBJECT TO CHANGE AT INNOCOMM'S DISCRETION. INNOCOMM MOBILE TECHNOLOGY GRANTS A NON-EXCLUSIVE RIGHT TO USE THE PRODUCT. THE RECIPIENT SHALL NOT TRANSFER, COPY, MODIFY, TRANSLATE, REVERSE ENGINEER, CREATE DERIVATIVE WORKS; DISASSEMBLE OR DECOMPILE THE PRODUCT OR OTHERWISE USE THE PRODUCT EXCEPT AS SPECIFICALLY AUTHORIZED. THE RECIPIENT UNDERTAKES FOR AN UNLIMITED PERIOD OF TIME TO OBSERVE CONFIDENTIALLITY REGARDING ANY INFORMATION AND DATA PROVIDED TO THEM IN THE CONTEXT OF THE DELIVERY OF THE PRODUCT. THIS GENERAL NOTE SHALL BE GOVERNED AND CONSTRUED ACCORDING TO TAIWAN LAW. Copyright Transmittal, reproduction, dissemination and/or editing of this document as well as utilization of its contents and communication thereof to others without express authorization are prohibited. Offenders will be held liable for payment of damages. All rights created by patent grant or registration of a utility model or design patent are reserved. Copyright © 2017, InnoComm Mobile Technology Corp. Trademark Notice InnoComm® is the trademarks of InnoComm Mobile Technology Corp. Other trademarks and registered trademarks mentioned herein are the property of their respective owners.
SN10-12 7/12/2017 REV 0.5 InnoComm Mobile Technology Confidential 3/14 TABLE OF CONTENT 1. INTRODUCTION ......................................................................................... 4 1.1. KEY FEATURES ............................................................................................................. 4 2.ELECTRICAL CHARACETRISTICS ............................................................. 5 2.1 RECOMMENDED OPERATING RANGE .................................................................................... 5 2.2 POWER CONSUMPTION .................................................................................................... 5 2.3 CHARACTERIZATION INFORMATION ...................................................................................... 5 3. RF CHARACTERISTICS .............................................................................. 6 4. SN10-12 PIN MAP AND SIGNAL DESCRIPTION....................................... 7 5. MODULE INSTALLATION GUIDE ............................................................... 8 5.1MECHANICAL INFORMATION .................................................................. 8 5.2. PCB LAYOUT FOOTPRINT ...................................................................... 8 5.3. MODULE INSTALLATION NOTICE ......................................................... 9 5.4. SMT SOLDER REFLOW NOTICE: ......................................................... 10 5.5. ANTENNA ............................................................................................... 11 6. APPENDIX .................................................................................................. 12 6.1 SW USER GUIDE INFORMATION. ......................................................... 12 FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT .............. 13 RADIATION EXPOSURE STATEMENT: .......................................................................... 14
SN10-12 7/12/2017 REV 0.5 InnoComm Mobile Technology Confidential 4/141. Introduction The IoT presents a different set of communications challenges to those faced by the conventional internet or cellular networks. Unlike cellphones and computers, IoT devices do not need to transfer large amounts of data. However, requirements for battery life and hardware cost are much more stringent and difficult to meet. For example, a soil moisture sensor might send a single moisture reading – one number – every hour. But to be practical for the farmer the batteries in the sensor need to last for at least one growing season, and ideally several years. SIGFOX networks provide a simplified way to connect low energy isolated devices to customer’s applications on wide territories, through a high efficiency radio technology with extreme budget links despite low radiations and at very low costs. Customers can then build their applications without any concern of the heavy radio network problematic and management, and, almost, no concern of the radio communication aspects. The SN10-12 is a transceiver module which complies with SIGFOX network specifications. The SN10-12 is based on NXP OL2385 chip which is a Sub-GHz wireless SoC transceiver. The SN10-12 module provides a wide range of frequency selections for IoT applications network service platform. 1.1. Key Features • High performance low power RISC micro-controller • Memory • 32kB EROM • 7kB RAM • Ultra Narrow Band Radio • Frequency Band: TX: 902.1375-904.6625MHz RX: 905.2 MHz • Output Power : 23.62 dBm
SN10-12 7/12/2017 REV 0.5 InnoComm Mobile Technology Confidential 5/14• Excellent Receiving Sensitivity: -125dBm @600bps 2GFSK • Excellent Image Rejection: 60 dB • Excellent Blocking Performance: 58 dB 2.ELECTRICAL CHARACETRISTICS 2.1 Recommended Operating Range PARAMETER CONDITIONS MIN TYP MAX UNIT Operating temperature range –40 25 85 °C Operating supply voltage 3.3 3.6 V 2.2 Power Consumption PARAMETER CONDITIONS MIN TYP MAX UNIT TX supply current at maximum output power @22dBm, 3.3V 240 260 mA RX 16.5 17.5 mA 2.3 Characterization information PARAMETER CONDITIONS MIN TYP MAX UNIT Voltage at digital I/O pins -0.3 VDD + 0.3 V
SN10-12 7/12/2017 REV 0.5 InnoComm Mobile Technology Confidential 6/143. RF Characteristics PARAMETER Model TX / RX UNIT Note Center Frequency SN10-12 902.2 / 905.2 MHz SIGFOX RCZ2 PARAMETER CONDITIONS MIN TYP MAX UNIT Note Antenna port impedance 50 Ω TX Characteristics Following characteristics are valid for conditions as follows (unless otherwise specified) Tamb = -40 °C to 85 °C, VSS = 0 V, VDD = 2.6 V to 3.6 V, crystal = 55.2 MHz PARAMETER CONDITIONS MIN TYP MAX UNIT Note Maximum output power, CW mode SN10-12 21 22 dBm RX Characteristics Following characteristics are valid for conditions as follows (unless otherwise specified) 2GFSK modulation, h = 2.67, BT = 1.0, NRZ, data-rate = 0.6 kChips/s, Channel spacing = 10 kHz, Channel filter bandwidth = 10 kHz, Frame Error Rate (FER) = 20%, payload length = 228 byte, crystal = 55.2 MHz. Tamb = 25 °C, VDD = 2.6 V to 3.6 V, fC = 905 MHz PARAMETER CONDITIONS MIN TYP MAX UNIT Note Sensitivity -40 °C to 85 °C -125 dBm PER at 10% on 1000 frames sent. Co-channel rejection 2GFSK jammer 2 5 dB Adjacent channel rejection Channel filter BW = 10 kHz, jammer same modulation as wanted. Channel separation: 10 kHz, 20 kHz, 150 kHz. 50 55 dB 55 60 dB 60 65 dB
SN10-12 7/12/2017 REV 0.5 InnoComm Mobile Technology Confidential 7/144. SN10-12 PIN Map and Signal Description Pin # Pin Name Type Description 1 GND GND Ground 2 VDD Power Power Supply input 3 GND GND Ground 4 GND GND Ground 5 GND GND Ground 6 GND GND Ground 7 GND GND Ground 8 GND GND Ground 9 P16 Digital I/O GPIO, SPI_SDI 10 P15 Digital I/O GPIO, SPI_CS 11 GND GND Ground 12 GND GND Ground 13 P14 Digital I/O GPIO, SPI_SCLK 14 P13 Digital I/O GPIO, SPI_SDO, UART_TX 15 P12 Digital I/O GPIO, UART_RX 16 P11 Digital I/O Debug port, INT, Optional 17 P10 Digital I/O GPIO, UART TX/RX CLOCK 18 RST_N Digital I/O GPIO, RESET 19 MDI_MSDA Digital I/O Debug port, MSDA 20 MDI_MSCL Digital I/O Debug, MSCL 21 GND GND Ground 22 P17 Digital I/O GPIO, SPI_AK 23 P20 Digital I/O Debug port, RSSI LOG 24 P21 Digital I/O N.C. 25 P22 Digital I/O N.C. 26 P23 Digital I/O GPIO 27 GND GND Ground 28 IF_IFN Digital I/O GPIO, IFN 29 IF_IFP Digital I/O GPIO, IFP 30 GND GND Ground 31 ANT RF RF Antenna Interface Impedance=50 Ω 32 GND GND Ground
SN10-12 7/12/2017 REV 0.5 InnoComm Mobile Technology Confidential 8/145. Module installation Guide 5.1Mechanical Information 5.2. PCB Layout Footprint
SN10-12 7/12/2017 REV 0.5 InnoComm Mobile Technology Confidential 9/145.3. Module installation Notice 5.3.1 Do not route traces under module to minimize on interference. (O) (X) 5.3.2 The trace Impedance of the antenna port (Pin 31) is 50 Ω. In order to minimize the return loss, it is recommended to use short traces.
SN10-12 7/12/2017 REV 0.5 InnoComm Mobile Technology Confidential 10/14 5.3.3 Keep enough clearance between the antenna port (Pin 31) and surrounding GND to minimize the power loss. (O) (X) 5.4 . SMT Solder Reflow Notice: Note: Allowable reflow soldering times: 2 times base on recommended reflow profile.
SN10-12 7/12/2017 REV 0.5 InnoComm Mobile Technology Confidential 11/14 5.5 Antenna design declaration: To compliance FCC KDB 996369 D01 v02 cause II. This module can only be used with a host antenna circuit trace layout design in strict compliance with the InnoComm instructions provided. The SN10-12 module use trace antenna in fixture board and compliance 47 CFR FCC Part 15 Subpart C (Section 15.247). For proper integration our modules in end products, we shall provided detailed and comprehensive instructions. Integrator, or end-user who use new antenna design will need to apply another FCCID and compliance FCC requirement., Antenna design Notice: Follow notice in section 5.3.2 and 5.3.3., the trace Impedance of the antenna port (Pin 31) is 50 Ω.
SN10-12 7/12/2017 REV 0.5 InnoComm Mobile Technology Confidential 12/14 Appendix 6.1 SW User Guide information. The SIGFOX software driver supports MCUs. These MCUs are a subset of the MCUs supported by the Kinetis Software Development Kit (KSDK) layer. This SW driver is built on the Analog Middleware Layer (AML), which creates an API abstraction layer for the desired Software Development Kit (SDK). The current implementation includes abstractions for KSDK 2.0 and S32 SDK. This allows support to be added for additional layers, such as the KSDK, without having to change the SIGFOX Software Driver itself. The detail Commend and SPI please read the web link as below. SigFox Software driver user guide http://cache.nxp.com/assets/documents/data/en/user-guides/OL2385SWUG.pdf?fsrch=1&sr=9&pageNum=1:
SN10-12 7/12/2017 REV 0.5 InnoComm Mobile Technology Confidential 13/14 Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
SN10-12 7/12/2017 REV 0.5 InnoComm Mobile Technology Confidential 14/14 Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. 3) Module approval valid only when the module is installed in the tested host or compatible series of host which have similar RF exposure characteristic with equal or larger antenna separation distance. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID:YAISN10-12”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

Navigation menu