InnoComm Mobile Technology 2213 Puzzle-B3 User Manual rev 2

InnoComm Mobile Technology Corporation Puzzle-B3 rev 2

User Manual rev 2

     Puzzle-B3 User's Manual          Regulatory model: 2213    manual-en-250-0823-E-AN240-v100   Avision Inc.
        2Federal Communication Commission Interference Statement  This  device  complies  with  Part  15  of  the  FCC  Rules.  Operation  is  subject  to  the following two conditions: (1) This device may not cause harmful interference, and (2) this  device must  accept  any interference received,  including  interference that  may cause undesired operation.  This equipment has been  tested and found to comply  with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.    These limits are designed to provide  reasonable  protection  against  harmful  interference  in  a  residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference  to  radio  communications.    However,  there  is  no  guarantee  that interference will not occur in a particular installation.    If this equipment does cause harmful  interference  to  radio  or  television  reception,  which  can  be  determined  by turning  the  equipment  off  and  on,  the  user  is  encouraged  to  try  to  correct  the interference by one of the following measures:  -  Reorient or relocate the receiving antenna. -  Increase the separation between the equipment and receiver. -  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -  Consult the dealer or an experienced radio/TV technician for help.  FCC  Caution:  Any  changes  or  modifications  not  expressly  approved  by  the  party responsible for compliance could void the user's authority to operate this equipment.  This transmitter must not be co-located or  operating  in conjunction with any other antenna or transmitter.     FOR MOBILE DEVICE USAGE (>20cm/low power)         Radiation Exposure Statement: This  equipment  complies  with  FCC  radiation  exposure  limits  set  forth  for  an uncontrolled  environment.  This  equipment  should  be  installed  and  operated  with minimum distance 20cm between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:  1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and   2) The transmitter module may not be co-located with any other transmitter or antenna.  As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed  IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.  End Product Labeling  This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: YAI2213”. The grantee's FCC ID can be used only when all FCC compliance requirements are met.   Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
       41     Starting from Your Mobile Device       Making Preparation To connect the Puzzle-B3 to a wireless LAN, prepare the followings:   An environment in which a wireless LAN is available When connecting the Puzzle-B3 to a wireless LAN, you may need information for a wireless access point such as an SSID (network name) and a security key (password). For details, contact your Network Administrator or refer to the manual for the wireless access point.    Attention! Do not place obstacles that block radio waves (e.g. walls or metal plates) or devices that cause radio wave interference (e.g. cordless phones) within 100 mm of the scanner, or near your wireless access point.   MB Application Download the MB Application on your mobile device from an application store such as Google Play.         MB
Connecting to A Wireless Network Connecting to a Wi-Fi network in an AP (Access Point) Mode  In AP (Access Point) mode, your mobile devices and the Puzzle-B3 are connected wirelessly without an additional AP (Access Point) since the Puzzle-B3 itself works as an AP.                  On your mobile devices, make sure indicates the last six digits of the Mac Address) has been selected as your network name (SSID).    Connecting the Scanner to a Wi-Fi Network in a Client Mode  In a Client mode, your mobile devices and Puzzle-B3 indicates are connected wirelessly through an additional AP (Access Point). This mode is also the default wireless mode.   Connecting Your Puzzle-B3 to an Access Point:   AP (Access Point) AP (Access Point)
        6  Important:   Note the wired and wireless mode can not work at the same time. To connect the Puzzle-B3 in a wireless network, please first disconnect the Ethernet cable connecting to your scanner.
2 Technical Support  If your problem still exists after trying the above solution, please contact our technical support.  Headquarter Avision Inc. No. 20, Creation Road I, Science-Based Industrial Park,  Hsinchu 300, Taiwan, ROC TEL: +886 (3) 578-2388 FAX: +886 (3) 577-7017 E-MAIL:    service@avision.com.tw Web Site: http://www.avision.com.tw  US and Canada Area   Avision Labs, Inc. 6815 Mowry Ave., Newark CA 94560, USA TEL: +1 (510) 739-2369 FAX: +1 (510) 739-6060 E-MAIL: support@avision-labs.com Web Site:   http://www.avision.com  China Area   Hongcai Technology Limited 7A, No.1010, Kaixuan Road, Shanghai 200052 P.R.C.   TEL :+86-21-62816680 FAX :+86-21-62818856 E-MAIL: sales@avision.net.cn Web Site: http://www.avision.com.cn  Europe Area  Avision Europe GmbH   Bischofstr. 101 D-47809 Krefeld Germany  TEL: +49-2151-56981-40 FAX: +49-2151-56981-42 E-MAIL: info@avision-europe.com Web Site: http://www.avision.de
        8  South American  Avision Brasil Ltda.  Rua Bamboré 41, Vila Monumento, Ipiranga. CEP: 04278-060, São Paulo, Brasil   TEL: +55-11-2737-2005 E-MAIL: suporte@avisionbrasil.com.br Web Site: http://www.avisionbrasil.com.br/

Navigation menu