Ingenico ICT220V3 Payment Terminal User Manual 900002734 05

INGENICO Payment Terminal 900002734 05

Manual

INGENICO – 28-32 Boulevard de Grenelle –75015 Paris - FRANCE Tél. 33(0)1 58 01 80 00 - Fax 33 (0)1 58 01 91 35 www.ingenico.com Product name : iCT220/iCT250 Range : COUNTER TOP U s e r G u i d e
Product name : iCT220/iCT250 • 2/20 Copyright © 2012 Ingenico 900002734 R11 000 05/4012 All rights reserved Contents 1. Introduction __________________________________________________ 3 2. Unpacking ___________________________________________________ 3 3. Recommendations_____________________________________________ 4 3.1. Security _____________________________________________________________4 3.2. Telephone emergency, hanging up _______________________________________4 3.3. Security of your terminal _______________________________________________5 3.4. Standard compliance marking ___________________________________________5 3.5. FCC compliance _______________________________________________________5 3.6. Main Characteristics ___________________________________________________7 4. Installation and connection _____________________________________ 8 4.1. Positioning the terminal ________________________________________________8 4.2. Connections__________________________________________________________8 4.3. Installing the iCT220/iCT250 – Cable fixing__________________________________8 4.3.1. Opening the cable cover_________________________________________________________ 8 4.3.2. Kit Magic Box installation________________________________________________________ 9 4.3.3. Connect cables _______________________________________________________________ 10 4.3.4. Close cover ___________________________________________________________________ 11 4.4. Installation of the Magic Box ___________________________________________ 11 4.5. Installing SAM (Secure access module)___________________________________ 12 4.6. Installing MicroSD Card (optional)_______________________________________ 13 5. Installing a paper roll __________________________________________14 6. Daily use _____________________________________________________15 6.1. Keypad functions ____________________________________________________ 15 6.2. Adjusting the contrast ________________________________________________ 15 6.3. Card insertion _______________________________________________________ 16 6.3.1. Swiping a card________________________________________________________________ 16 6.3.2. Inserting a chip card ___________________________________________________________ 16 6.3.3. Inserting a chip card in second reader (Optional) ____________________________________ 16 6.3.4. Reading Contactless (Optional) __________________________________________________ 16 7. Maintenance _________________________________________________17 7.1. Paper roll ___________________________________________________________ 17 7.2. Cleaning of the terminal _______________________________________________ 18 7.3. Transport and storage ________________________________________________ 18 7.4. Troubleshooting _____________________________________________________ 18 7.5. End of life___________________________________________________________ 19
Product name : iCT220/iCT250 • 3/20 Copyright © 2012 Ingenico 900002734 R11 000 05/4012 All rights reserved 1. Introduction Thank you for choosing an Ingenico payment terminal. We recommend you to read carefully this user guide: It gives you the necessary information about safety precautions, unpacking, installation, and maintenance of your terminal. CAUTION To benefit from the guarantee-related product, and to respect the security, we ask you to use only the power supply delivered in box with the product, entrusting maintenance operations only to an authorized person. Failure to comply with these instructions will void the manufacturer’s responsibility. 2. Unpacking ADVICE Carefully preserve the packaging of the iCT220/iCT250. It must be re-used whenever the terminal is shipped. According to the model, the following items are included in the iCT220/iCT250 box • The iCT220/iCT250 terminal equipped with its paper roll • Magic box ( mandatory use ) • The main power supply with its cable connection (according to the national needs). • The cable connection for the telephone network • This installation guide CAUTION The power supply unit provided with your equipment is specially designed for Ingenico iCT220/iCT250 terminals. Do not use any other power supply. Cable connection for the telephone network Magic box Desktop Power supply unit iCT220/iCT250 terminal User guider
Product name : iCT220/iCT250 • 4/20 Copyright © 2012 Ingenico 900002734 R11 000 05/4012 All rights reserved 3. Recommendations 3.1. Security Power on/Power down To power on or power down the iCT220/iCT250 connect or disconnect the power supply from the electric outlet. Lithium battery The iCT220/iCT250 is fitted with a lithium battery which is not accessible to the user. Only a qualified technician may be authorized to open the unit and change this component. Electrical power supply network Provide an electrical outlet : - located near the equipment and easily accessible - which meets the standards and regulations in the country of use. Telephone network Provide a phone jack complying with standards and regulations in the country of use. SAM/SIM or SD Memory Card compartment cover Located under the terminal, it must be in place during normal operation of the terminal. Cable compartment cover The cable compartment cover is located under the terminal, it must be in place during normal operation of the terminal. 3.2. Telephone emergency, hanging up You have an urgent call to make, when iCT220/iCT250 hangs on the line. In order to get a dial tone… Place the handset in the hang up position and : press the red key (=cancel) or disconnect the power supply from the mains network or disconnect the iCT220/iCT250 telephone connector from the telephone call socket, and place the telephone connector into the telephone wall socket. You will have a dial tone within 6 seconds.
Product name : iCT220/iCT250 • 5/20 Copyright © 2012 Ingenico 900002734 R11 000 05/4012 All rights reserved 3.3. Security of your terminal Upon receipt of your terminal you should check for signs of tampering of the equipment. It is strongly advised that these checks are performed regularly after receipt. You should check, for example: that the keypad is firmly in place; that there is no evidence of unusual wires that have been connected to any ports on your terminal or associated equipment, the chip card reader, or any other part of your terminal. Such checks would provide warning of any unauthorised modifications to your terminal, and other suspicious behaviour of individuals that have access to your terminal. Your terminal detects any “tampered state”. In this state the terminal will repeatedly flash the message” Alert Irruption!” and further use of the terminal will not be possible. If you observe the “Alert Irruption!” message, you should contact the terminal helpdesk immediately. You are strongly advised to ensure that privileged access to your terminal is only granted to staff that have been independently verified as being trustworthy. CAUTION NEVER ask the customer to divulge their PIN Code. Customers should be advised to ensure that they are not being overlooked when entering their PIN Code. 3.4. Standard compliance marking iCT220 • This class (B) digital apparatus complies with Canadian ICES-003 iCT220 / iCT250 • conforms to the following standards and rules : – IEC 60950-1 2nd Ed: Electrical safety of data processing equipment including electrical office equipment – FCC part 15 C (ICT250 ), FCC part 15 B(ICT220 ) – FCC part 68 – EN 55024 3.5. FCC compliance FCC ID : XKB-ICT220 / XKB-ICT250 / XKB-ICT220V3 / XKB-ICT250V3 This equipment as been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interface in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct interface by one more of the following measures : • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into a outlet on circuit different from that to which the receiver is connected. • Consult the dealer or an experience radio/TV technician for help.
Product name : iCT220/iCT250 • 6/20 Copyright © 2012 Ingenico 900002734 R11 000 05/4012 All rights reserved Part 68 of FCC Rules US : IEOMM01BICT220 / IEOMM01BICT250 US : IEOMM01BICT220V3 / IEOMM01BICT250V3 This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US: AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. This equipment uses the following USOC jacks: (RJ11C). A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of this equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications to maintain uninterrupted service. If trouble is experienced with this equipment, please contact INGENICO, or your local INGENICO distributor or service center in the U.S.A. for repair and/or warrant information. If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. U.S.A service center: Ingenico USA 6195 Shiloh Road, Suite D Alpharetta, GA 30005 United States Tel: +1(678) 456 1200 Fax: +1 (678) 456 1201 Email: info.us@ingenico.com CAUTION The user is cautioned that any changes or modification not approved by INGENICO could void user’s authority to operate the equipment.
Product name : iCT220/iCT250 • 7/20 Copyright © 2012 Ingenico 900002734 R11 000 05/4012 All rights reserved 3.6. Main Characteristics Terminal Weight about 325 g to 350 g full option Size 185 x 83 x 63 mm (l x w x h) Power supply unit (wall mounted) Weight approx 115 g (without mains cable) Size approx 77 x 25 x 89 mm (L x w x h) Class Class II equipment Input voltage 120V-60Hz Max consumption 400 mA The power supply unit is especially designed by the manufacturer for its terminals and so must be used. Desktop power supply unit Weight approx 230 g (without mains cable) Size approx 98 x 50 x 30 mm (L x w x h) Class Class II equipment Input voltage 100-240VCA-50-60 Hz Max consumption 800 mA Cable length Power block cable approx 1,8 m Telephone cable approx 3 m
Product name : iCT220/iCT250 • 8/20 Copyright © 2012 Ingenico 900002734 R11 000 05/4012 All rights reserved 4. Installation and connection 4.1. Positioning the terminal Install the terminal on a flat surface, with an easy access to an electrical outlet and telephone line. Place the terminal away from any heat source and protected from dust, vibrations and electromagnetic radiations (away from video terminals, PC, anti-shoplifting barriers ...). Operating conditions Ambient temperature from +5°C to +40°C Max relative humidity 85% at +40°C Storage conditions Storage temperature -20°C, +55°C Max relative humidity 85% at +55°C 4.2. Connections All connections are on the rear of the terminal protected by a cover. * according to the model 4.3. Installing the iCT220/iCT250 – Cable fixing 4.3.1. Opening the cable cover • Unclip the cover by pushing simultaneously on the clips 1 with your nails finger as shown on the figure here below. • Lift the cover rearward to remove it, as shown by arrows on the figure. Serial Link RS232 Telephone USB Slave Ethernet Link (Optional)* USB Host Second Serial Link RS232 (Optional)* Power Supply 1
Product name : iCT220/iCT250 • 9/20 Copyright © 2012 Ingenico 900002734 R11 000 05/4012 All rights reserved 1 2 4 3 caps 4.3.2. Kit Magic Box installation WARNING Connecting must be done when the terminal is powered off. Follow the installation instructions shown below: • Plug: 1 Power lead 2 Telephone line 3 Ethernet cable 4 Serial link RS232 cable • Install caps in the lead-through (as indicated on the figure). • Close the compartment with the special cover provided in the kit, like the procedure described at chapter 4.3.4.
Product name : iCT220/iCT250 • 10/20 Copyright © 2012 Ingenico 900002734 R11 000 05/4012 All rights reserved 4.3.3. Connect cables Perform the following operations: • Plug the telephone cable (1) into the telephone jack (3). Connect the other end into the connection (4) of the magic box • Plug the power leads (5) into the power outlet (6), connect the other end into the power connection (7) of the magic box. Plug: TNV-3 circuit: Telecommunication Network Voltage, as per safety standard EN 60950. 6 3 4 1 7 5
Product name : iCT220/iCT250 • 11/20 Copyright © 2012 Ingenico 900002734 R11 000 05/4012 All rights reserved 4.3.4. Close cover • To close the cover, start by inserting the clips 1 of the cover in their housing respectively first, as shown on the figure here below, and close the cover. 4.4. Installation of the Magic Box ADVICE It is strongly recommended to attach the “Magic cable” to terminal’s work area in order to reduce stress on the terminal and connection. Examples of securing the “Magic Cable” are as illustrated: 1 Using the supplied cable tie to attach to a table leg (or similar) 2 Using the supplied cable tie and self-adhesive support 3 Using a counter-sunk screw (not supplied) to an appropriate surface • The “Magic Cable” should be readily accessible for support and terminal helpdesk diagnosis purposes. Note: The connection Magic Box can also be attached using a VELCRO™ or other system. 1 1 3 2
Product name : iCT220/iCT250 • 12/20 Copyright © 2012 Ingenico 900002734 R11 000 05/4012 All rights reserved 4.5. Installing SAM (Secure access module) CAUTION: Before starting, switch off the terminal by disconnecting the power supply. In order to access the SAM card you must first remove the SAM compartment cover located at the back of your terminal. • Press down firmly in the middle of the cover and slide it as indicated by arrow on the figure below. • Insert the SAM Card into the slot marked (1) or(2). Take care to ensure that the SAM Card is inserted in the correct manner. The cut corner must be positioned as indicated on the figure. • To remove SAM card, we suggest you to use a piece of adhesive previously pasted on both sides of the SAM as shown here below CAUTION: Do not use any tools when installing or removing the SAM Card. Replace the cover as illustrated by the procedure below: PRESS HERE SAM Cut corner Adhesive Cut corner
Product name : iCT220/iCT250 • 13/20 Copyright © 2012 Ingenico 900002734 R11 000 05/4012 All rights reserved 4.6. Installing MicroSD Card (optional) CAUTION: Before starting, switch off the terminal by disconnecting the power supply. • Open the cover as indicated at chapter 4.5 • Insert completely the MicroSD Card into the slot marked (MicroSD) as indicated on the figure. Take care to ensure that the MicroSD Card is inserted in the correct manner. The insertion position Card is engraved on the terminal. • To remove the MicroSD Card push on it with your finger nails.
Product name : iCT220/iCT250 • 14/20 Copyright © 2012 Ingenico 900002734 R11 000 05/4012 All rights reserved 5. Installing a paper roll Your terminal is supplied with one paper roll. When the paper roll is nearing the end, a red line will appear on the paper, this indicates that the paper roll must be replaced. CAUTION Use only paper approved by the manufacturer (diameter 40 mm). Use of unsuitable paper is likely to damage the printer of your terminal (see characteristics at the chapter 7.1). • Open the paper compartment by lifting the catch located at the rear of the iCT220/iCT250 and pulls the cover to the rear of the terminal. ATTENTION Do not force the cover against the cables. • Insert the paper roll in the compartment following the directions shown on the figure below. • Pull the paper up to the top of the terminal and hold it in this position. • Maintain the paper and close the lid. • Press the top of the lid in the center as shown by arrow, until it clips into position. ADVICE If you are inserting a new roll, tear off the first length (one complete turn). LIFT
Product name : iCT220/iCT250 • 15/20 Copyright © 2012 Ingenico 900002734 R11 000 05/4012 All rights reserved 6. Daily use 6.1. Keypad functions 1 NAVIGATION keys in the menus – Interactive keys for use between the screen 2 FUNCTION keys F 3 CANCEL key (red) 4 CLEAR key (yellow) / Feed paper (long press) 5 VALIDATION key (green) 6 Dot Key 6.2. Adjusting the contrast No contrast management for the Colour display The screen of your chart is 128 x 64 pixels, illuminated with white light. If you wish to increase or to decrease the contrast of the characters displayed on screen, press simultaneously on the (dot key) and key in order to decrease the contrast, or the (dot key) and key in order to increase. Keep pressing the keys as long as necessary. 1 2 3 4 5 6
Product name : iCT220/iCT250 • 16/20 Copyright © 2012 Ingenico 900002734 R11 000 05/4012 All rights reserved 6.3. Card insertion 6.3.1. Swiping a card • Slide the card in the reader with magnetic strip facing left Swipe the card with constant speed, not too slow not too fast, to maximize the reading and avoid annoying repetitions. 6.3.2. Inserting a chip card • Chip Cards should be inserted into the card reader as illustrated with the chip facing up 6.3.3. Inserting a chip card in second reader (Optional) Is located on back of the terminal. • Insert the card up side down, magnetic strip visible. (chip no visible) 6.3.4. Reading Contactless (Optional) • Bring the card quickly up to the active zone above the display (at about 1cm). Keep the card close to the display during the transaction Your contactless terminal has a row of four status lights that are visible on display. • When a contactless transaction is started the first (left hand) status light will be lit steadily; this indicates that the contactless display is in use but a card is not being read. • When a contactless card is presented to the contactless active zone during a transaction, the second, third and fourth status lights will be lit in turn. The card read is successful when all four status lights are lit and the confirmation tone is heard. Green lights Contact’less Active Zone
Product name : iCT220/iCT250 • 17/20 Copyright © 2012 Ingenico 900002734 R11 000 05/4012 All rights reserved 7. Maintenance WARNING Before making any operations of maintenance in the terminal, make sure that the power supply is disconnected. 7.1. Paper roll Characteristics Precisions Colour White Width 58 mm Diameter 40 mm max. • The thermal paper can be deteriorated by poor storage conditions, so we recommend you to avoid: – storage in hot wet places (near to air-conditioner, humidity higher than 85%) – exposure to sunlight or ultraviolet for long periods – contact with organic solvents (solvent type adhesive) – direct contact with materials containing plasticizers (PVC transparent folders or envelopes) – direct contact with «diazo» papers – direct contact with water – Rubbing or pressing the paper too strongly CAUTION In order to benefit from the complete guarantee of the product, only heat sensitized paper approved by the manufacturer can be used.
Product name : iCT220/iCT250 • 18/20 Copyright © 2012 Ingenico 900002734 R11 000 05/4012 All rights reserved 7.2. Cleaning of the terminal First of all, unplug all the wires from the terminal. Good rules for proper cleaning of the terminal are: • Use a soft cloth that is very slightly soaked with soapy water to clean the outside of the terminal. • Do not clean the electrical connections. • Do not use in any case, solvents, detergents or abrasive products: Those materials might damage the plastic or electrical contacts. • Avoid exposing the terminal to the direct rays of the sun. • Do not put anything into the slot of the smart card reader 7.3. Transport and storage • Use the original packaging for any unit or stored. • Disconnect all cables from the terminal during the transport. 7.4. Troubleshooting The terminal does not turn on or does not connect to the telephone line • Check the power supply and telephone line cables • Check for electrical power network The terminal fails to establish a telephone connection • Check that the tone of the phone line is free • Check the configuration of the phone line and number to call • Get support from technical Cards are not read • Check that the magnetic card is swiped correctly (with magnetic stripe facing left) • Swipe again the card with a constant and quick movement • Verify that the magnetic strip is not damaged, grooved or cracked • Make sure you have inserted correctly the smart card into the smart card reader and removed the card only after the transaction The ticket is not printed • Check the presence and proper positioning of the paper roll. Possibly adjust the paper roll following instructions present in this manual • Check the type of paper used (thermal paper must be used)
Product name : iCT220/iCT250 • 19/20 Copyright © 2012 Ingenico 900002734 R11 000 05/4012 All rights reserved 7.5. End of life The product belongs to the family of electrical and electronic equipment. Therefore, it is subjected to the WEEE directive which requires the collection and the recycling at the end of life product. The Ingenico products present the symbol for the marking of electrical and electronic equipment as required by the WEEE Directive. The crossed-out wheeled bin printed on the product gives the information about the requirement not to dispose of WEEE as unsorted municipal waste and to collect such WEEE separately. To assure that the product is collected and recycled with respect to the environment, you must contact your supplier (in defect, contact the Ingenico local office or the commercial head office in charge of your country on www.ingenico.com, « contact us » page). The abandonment or uncontrolled disposal of waste can cause harm to environment and to human health. So, by recycling your product in a responsible manner, you contribute to the preservation of natural resources and to the protection of human health.
Product name : iCT220/iCT250 • 20/20 Copyright © 2012 Ingenico 900002734 R11 000 05/4012 All rights reserved Ingenico 28-32 Boulevard de grenelle 75015 Paris - France Tél.: + 33 1 58 01 80 00 - Fax: + 33 1 58 01 91 35 www.ingenico.com Your contact “This Document is Copyright © 2012 by INGENICO Group. INGENICO retains full copyright ownership, rights and protection in all material contained in this document. The recipient can receive this document on the condition that he will keep the document confidential and will not use its contents in any form or by any means, except as agreed beforehand, without the prior written permission of INGENICO. Moreover, nobody is authorized to place this document at the disposal of any third party without the prior written permission of INGENICO. If such permission is granted, it will be subject to the condition that the recipient ensures that any other recipient of this document, or information contained therein, is held responsible to INGENICO for the confidentiality of that information. Care has been taken to ensure that the content of this document is as accurate as possible. INGENICO however declines any responsibility for inaccurate, incomplete or outdated information. The contents of this document may change from time to time without prior notice, and do not create, specify, modify or replace any new or prior contractual obligations agreed upon in writing between INGENICO and the user. INGENICO is not responsible for any use of this device, which would be non consistent with the present document. All trademarks used in this document remain the property of their rightful owners.” *296114093AE*

Navigation menu