Ingenico D5000CLWIBT Payment Terminal User Manual 900024281 R11 000 07 DESK SERIES NAR indd

INGENICO Payment Terminal 900024281 R11 000 07 DESK SERIES NAR indd

Contents

User manual reduced.pdf

www.ingenico.com28-32, boulevard de Grenelle, 75015 Paris - France / (T) +33 (0)1 58 01 80 00 / (F) +33 (0)1 58 01 91 35Ingenico - SA au capital de 47 656 332 / 317 218 758 RCS Nanterre Desk SeriesUser Guide
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved2Contents1_Introduction2_Unpacking3_Recommendations 3_1 Safety / Sicherheit 3_1_1 Safety 3_1_2 Sicherheit 3_2 Telephone emergency, hanging up 3_3 Security of your terminal (tampering attempt detection) 3_4 Desk series : Fixed Installation 3_5 Characteristics 3_5_1 Main Characteristics 3_5_2 Haupteigenschaften4_Installation 4_1 Positioning the terminal 4_2 Aufstellung des Terminals 4_3 Connections 4_4 Installing the Terminal - Cable xing 4_4_1 Kit Magic Box installation (optional) 4_5 Installing SAM (Secure access module)45136681367891011131415172010
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved3 4_6 Installing MicroSD Card (optional) 4_7 Installing SIM for GPRS (optional) 4_8 Installing SAM3 (optional) 4_9 Installing 2nd SIM for GPRS (optional)5_Installing a paper roll6_Daily use 6_1 Keypad functions 6_2 Adjusting the contrast (B&W display only) 6_3 Card insertion 6_3_1 Swiping a card 6_3_2 Inserting a chip card 6_3_3 Reading Contacless (Optional) 6_3_4 Headphone output (Optional)7_Maintenance / Wartung 7_1 Paper roll 7_2 Cleaning of the terminal 7_3 Transport and storage 7_4 Troubleshooting 7_5 Troubleshooting8_Markings 8_1 FCC/IC Compliance212223242527272828282828303030313232333335
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved41_IntroductionThank you for choosing an Ingenico payment terminal.We recommend you to read carefully this user guide: It gives you the necessary information about safety precautions, unpacking, installation, and maintenance of your terminal.WARRANTY / SECURITYTo benet from the guarantee-related product, and to respect the security, we ask you to use only the power supply delivered in box with the product, entrusting maintenance operations only to an authorized person.Failure to comply with these instructions will void the manufacturer’s responsibility.This symbol indicates an important Warning.This symbol indicates a piece of advice.GARANTIE / SICHERHEITUm bestmöglich von dem garantierten Produkt zu protieren und die Sicherheitsbedingungen zu gewährleisten, bitten wir Sie ausschließlich das der Verpackung beiliegende Netzteil zu benutzen und ausschließlich befugte Personen mit der Wartung zu beauftragen.Bei Nichtbeachtung dieser Anweisung erlischt die Haftbarkeit des Herstellers.Dieses Symbol weist auf eine wichtige Warnung.
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved52_UnpackingCable connection for the telephone or Ethernet networkTerminalWall mounted power supply unitAccording to the model, the following items are included in the packaging box (including optional accessories):The terminal equipped with its paper rollThe power supply with its cable connection (according to the national needs).The cable connection for the telephone or Ethernet networkThis installation guideRadio model (all)Desktop power supply unit required if terminal is  tted with the following options:Contactless modelCAUTIONThe power supply unit provided with your equipment is specially designed for it. Do not use any other power supply.User guideWARNHINWEISBitte verwenden Sie ausschließlich das mitgelieferte Netzteil, kein anderes Netzteil.
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved63_RecommendationsTo power on or power down the terminal connect or disconnect the power supply from the electric outlet.Power on/Power down – Emergency stopThe terminal is tted with a lithium battery cell which is not accessible to the user. Only a qualied technician is authorized to open the unit and change this component.Lithium battery cellThe electrical outlet must meet the following criteria: Electrical power supply networkMust be installed near the equipment and easily accessible;Must meet standards and regulations in the country of use;For type A plug, the protection of the installation must be set to 20 A.The phone network must comply with standards and regulations in the country of useTelephone networkCertain regulations restrict the use of radio equipment in chemical plants, fuel depots and any site where blasting is carried out. You are urged to comply with these regulations. The terminal shall be protected by a specially tted and certied cover enabling use in proximity to a fuel pump.Explosion areasAccording to the model your terminal could be a radio transmitter which may interfere with health appliances, such as hearing aids, pacemaker, hospital equipment, etc. Your doctor or the equipment manufacturer will be able to provide you with appropriate advice.Electronic health appliances3_1 Safety / SicherheitADVICE Keep the packaging. It must be re-used whenever the terminal is shipped.3_1_1 SafetyExcept for Norway do not connect on an IT electrical network.
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved7Located under the terminal, it must be in place during normal operation of the terminal.Le réseau téléphonique doit être conforme aux normes et réglementations en vigueur dans le pays d’utilisation.Bottom side compartment trapdoor3_1_2 SicherheitZum Ein-oder Ausschalten der Klemme stecken oder ziehen Sie das Netzkabel aus der Steckdose.Power ein/Power aus – NothaltDas Terminal ist mit einer Lithiumbatterie ausgestattet, die für den Benutzer unzugänglich ist. Nur ein qualizierter Techniker sollte die Box zu öffnen, um die Komponente zu ersetzen.Lithium-BatterieEinen Telefonstecker gemäß den Normen und Vorschriften des Benutzerlandes bereitstellen.TelefonnetzEinige Vorschriften beschränken den Einsatz von Funkgeräten in Chemieanlagen, Kraftstofagern und anderen Standorten mit Explosionsgefahr. Sie werden gebeten, diese Vorschriften einzuhalten. Das Terminal muss durch eine Abdeckung geschützt werden, die für den Einsatz in der Nähe einer Kraftstoffpumpe speziell entwickelt und zertiziert ist.Explosionsgefährdung Je nach Modell, könnte Ihr Gerät ein Funksender sein, der medizinische Gerste wie Hörgeräte, Herzschrittmacher, Krankenhausausrüstung, usw. stören kann. Ihr Arzt oder der Hersteller ist in der Lage, Sie entsprechend zu beraten.Elektronik Gesundheit Sie bendet sich unter dem Terminal und muss bei normalem Terminalbetrieb angebracht sein.Die untere Gehäuseabdeckung Die Steckdose muss die folgenden Kriterien erfüllen:Anschluss an das StromnetzIn der Nähe des Geräts benden und leicht zugänglichErfüllt die Normen und Vorschriften im EinsatzlandTyp-A Stecker müssen mit 20A abgesichert sein.Mit Ausnahme von Norwegen nicht an ein IT-Stromnetz anschließen.
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved83_2 Telephone emergency, hanging up You have an urgent call to make, when terminal hangs on the line.Perform as follow in order to get a dial tone…Place the handset in the hang up position and: Press the red key (=cancel)Or disconnect the power supply from the mainsOr disconnect the terminal telephone connector from the telephone line socket, and place the telephone connector into the telephone line socket.You will get a dial tone within 6 seconds.3_3 Security of your terminal (tampe-ring attempt detection) Your device fulls current applicable PCI PTS security requirements.Upon receipt of your terminal you should check for signs of tampering of the equipment. It is strongly advised that these checks are performed regularly after receipt. You should check, for example: that the keypad is rmly in place; that there is no evidence of unusual wires that have been connected to any ports on your terminal or associated equipment, the chip card reader, or any other part of your terminal. Such checks would provide warning of any unauthorized modications to your terminal, and other suspicious behavior of individuals that have access to your terminal. Your terminal detects any “tampered state”. In this state the terminal will repeatedly ash the message” Alert Irruption!” and further use of the terminal will not be possible. If you observe the “Alert Irruption!” message, you should contact the terminal helpdesk immediately.You are strongly advised to ensure that privileged access to your terminal is only granted to staff that have been independently veried as being trustworthy.The terminal must never be put in or left at a location where it could be stolen or replaced by another device.Your device is also available with PCI PTS compliant pin-shield:
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved9CAUTIONPositioning of the terminal on check stand must be in such a way to make cardholder PIN (Personal Identication Number) spying infeasible. Installing device on an adjustable stand must be in such a way that consumers can swivel the terminal sideways and/or tilt it forwards/backwards to a position that makes visual observation of the PIN-entry process difcult. Positioning of in-store security cameras such that the PIN-entry keypad is not visible. NEVER ask the customer to divulge their PIN Code. Customers should be advised to ensure that they are not being overlooked when entering their PIN Code.3_4 Desk series : Fixed Installation If the device is to be used in a situation where it is not possible for thecardholder to pick up and shield their PIN entry themselves, the device may be used without PIN shield, but it must be installed in the following manner:a) The device must be angled at 45 or more, so that oversight of the PINentry from the rear of the device is not possible.b) The device must either be tted in a swivel stand – so that the customer can position the device in the best angle to prevent oversight– or the device must be xed in the best possible position to prevent oversight if such a generic position exists in the specic environmentto which the device is installed.c) The device environment must be accompanied with conspicuous notices and educational material which informs the customer to shieldtheir PIN during PIN entry.d) The device must be deployed so that oversight from other customers, either in different payment lanes, or in other areas of the shopping environment, is prevented. This may be achieved through the placement of the lanes and device , so that the customer is automatically positioned between the device keypad and other customers. Alternatively, it may be achieved by the environment in which the device is installed, so that the checkout itself shields the PINentry process.e) The terminal is exclusively made for indoor use If the above conditions are not fullled, the device with PIN shield must be used.
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved10Power supply unit (wall mounted)Weight approx 115 gSize approx 77 x 25 x 89 mm (L x w x h)Class Class II equipmentInput voltage AC 230V 50-60HzOutput voltage DC 8V 2A4A Desktop power supply unitWeight approx 230 g (without mains cable)Size approx 115 x 52 x 32 mm (L x w x h)Class Class II equipmentInput voltage AC 100-240V 50-60HzOutput voltage DC 8V 4AThe power supply unit is especially designed by the manufacturer forits terminal with radio transceivers, do not use another one.3A Desktop power supply unitWeight approx 191 g (without mains cable)Size approx 118 x 48 x 31 mm (L x w x h)Class Class II equipmentInput voltage AC 100-240V 50-60HzOutput voltage DC 8V 3AThe power supply unit is especially designed by the manufacturer forits terminal with contactless function, do not use another one.3_5 Characteristics / Haupteigenschaften 3_5_1 Main CharacteristicsWeight (w/o paper roll) about 310 g to 340 g full optionSize 187 x 82 x 68 mm (l x w x h)Terminal
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved11Accordance terminal / type of power supplyLabel on terminal Type power supply (wall mounted)Power block cable approx 1,8 mCable lengthapprox 3 mTelephone cable3_5_2 HaupteigenschaftenGewicht 310 g bis 340 g bei allen Optionen Größe 187 x 82 x 68 mm (L x B x H)TerminalGewicht ungefähr 115 g (ohne Netzkabel)Größe ungefähr 75 x 25 x 89 mm (L x B x H)Netzteil (an der Wand angebracht)Klasse Ausrüstung Klasse IIEingangsspannung AC 230V 50-60HzAusgangsspannung DC 8V 2ALabel on terminal Type power supply8V 2A Plug power supply (wall mounted) (Output 2A)Recommended for terminals without any Radio transceivers (ie : Ethernet/Modem).8V 4ADesktop power supply (Output 3A) Recommended for terminals with Contactless8V 3ADesktop power supply (Output 4A) Recommended for terminals with Radio transceivers (2G, 3G, Wi, Bluetooth)
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved12KabellängeNetzteilkabel ungefähr 1,8 mungefähr 3 m TelefonkabelGewicht ungefähr 230 g (ohne Netzkabel)Größe ungefähr 115 x 52 x 32 mm (L x B x H)4A BüronetzadapterKlasse Ausrüstung Klasse IIEingangsspannung AC 100-240V 50-60HzAusgangsspannung DC 8V 4ADer Netzteil wurde speziell vom Hersteller für seine Terminals entworfen und muss mit diesen benutzt werden.Der Netzteil wurde speziell vom Hersteller für seine Terminals entworfen und muss mit diesen benutzt werden.Gewicht ungefähr 191 g (ohne Netzkabel)Größe ungefähr 118 x 48 x 31 mm (L x B x H)3A BüronetzadapterKlasse Ausrüstung Klasse IIEingangsspannung AC 100-240V 50-60HzAusgangsspannung DC 8V 3ALabel terminal Netzteiltyp8V 2APlug Netzadapter (Befestigung an der Wand) (OUTPUT 8V 2A) oderBüronetzadapter (OUTPUT 8V 4A)Dazugehöriges Terminal / Netzteiltyp8V 4A Büronetzadapter (OUTPUT 8V 4A)8V 3A Büronetzadapter (OUTPUT 8V 3A)
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved134_Installation4_1 Positioning the terminalInstall the terminal on a at surface, with an easy access to an electrical outlet and telephone line. Place the terminal away from any heat source and protected from dust, vibrations and electromagnetic radiations (away from video terminals, PC, anti-shoplifting barriers, ...). The terminal is exclusively made for indoor use.Ambient temperature from 0°C to +40°CMax relative humidity 85% at +40°COperating conditions2000 mMax altitudeStorage temperature -20°C, +55°CMax relative humidity 85% at +55°CStorage conditions4_2 Aufstellung des Terminals Stellen Sie das Terminal auf eine ache Oberäche mit einfachem Zugang zu einer Netzsteckdose und Telefonleitung. Stellen Sie das Terminal nicht in der Nähe von Wärmequellen auf und schützen Sie es vor Staub, Vibrationen und elektromagnetischen Strahlungen (weit entfernt von Videoterminals, PCs, Diebstahlschranken, etc.)Umgebungstemperatur 0°C bis +40°CMaximale Luftfeuchtigkeit 85% bei +40°CBetriebsbedingungen2000 mMaximale HöheLagertemperatur -20°C, +55°CMaximale Luftfeuchtigkeit 85% bis +55°CLagerbedingungen
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved144_3 ConnectionsAll connections are on the rear of the terminal protected by a down side trapdoor.Phone : TNV-3.Power Supply : Limited Power Source.Other connections : Safety Extra-low Voltage.According to IEC60950-1 and EN60950-1*according to the modelTelephone (Optional)*Power SupplyµSD (Optional)*SIM 1 & 2 (Optional)*Serial LinkRS232Ethernet Link(Optional)*10/100 BaseTUSB HostUSB Host/Slave2nd SerialLink RS232(Optional)*SAM 1 & 2SAM 3 (Optional)*
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved154_4 Installing the Terminal - Cable  x i n gOpening down-side trapdoorUnclip the trapdoor by pushing on the clip with your  nger as shown on the  gure here below.Then lift the trapdoor rearward to remove it, as shown by arrowson the  gureClosing down-side trapdoorTo close the trapdoor, start by landing trapdoor on to bottom casing as shown on the  gure , manage 5/6mm distance for clip insertion then push and clip it.
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved16WARNINGConnecting is to be made when the terminal is powered off.WARNHINWEISDie Anschlüsse müssen bei ausgeschaltetem Terminal erfolgen.Perform the following operations:Plug telephone line , equipped if necessary with user country speci c converter , to the telephone network (*). Connect the other end to the terminal telephone connection . If necessary, connect the telephone (Telephone is not required for the terminal to operate) Open down side trapdoor then unclips the cables hookOptionally plug others cables (Ethernet, RS232, USB…)Plug PSU power lead into the power socket .Connecting cables
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved17(*): TNV-3 circuit: Telecommunication Network Voltage, as per safety standard EN 60950-1.4_4_1 Kit Magic Box installation (optional)WARNINGConnecting is to be made when the terminal is powered off.WARNHINWEISDie Anschlüsse müssen bei ausgeschaltetem Terminal erfolgen.For instance, possible con guration for FrancePlug the power supply into the mains.Clips the cables-hook part to secure cables path then close down side trapdoor
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved18Perform operations as described in “connecting cables” chapter and connect cables as follow:Cables to plug:Power leadTelephone lineEthernet cableSerial link RS232 cableInstall through-holes in the lead-through guides (as indicated on the gure).If you need extra cables then cut undesired over-molded section at
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved19It is strongly recommended to secure the “Magic cable” to terminal’s work area in order to reduce stress on terminal and connection.ADVICEUsing the supplied cable tie to attach to a table leg (or similar)Using the supplied cable tie and self-adhesive supportUsing a counter-sunk screw (not supplied) to an appropriate surfaceThe “Magic Cable” should be readily accessible for terminal maintenance and helpdesk diagnosis purposes.The connection Magic Box can also be attached using a VELCRO™ or other system.NOTE:
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved204_5 Installing SAM (Secure access module)CAUTIONBefore starting, switch off the terminal by disconnecting the power supply.Perform the following operations:Open down side trapdoor Insert the SAM Card into the slot marked (1) or (2). Take care to ensure that the SAM Card is inserted in the correct manner. The cut corner must be positioned as indicated on the  gure.Cut cornerClose down side trapdoorWe suggest you to use a piece of adhesive previously pasted on both sides of the SAM as shown here below for easy removalWARNHINWEISBevor Sie beginnen, das Gerät auszuschalten, indem Sie das Netz.
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved21Cut cornerAdhesiveCAUTIONDo not use any tools when installing or removing the SAM Card.4_6 Installing MicroSD Card (optional)CAUTIONBefore starting, switch off the terminal by disconnecting the power supply.WARNHINWEISZum Einsetzen oder Entfernen der SAM Karte keinerlei Werkzeug benutzen.WARNHINWEISBevor Sie beginnen, das Gerät auszuschalten, indem Sie das Netz.Perform the following operations:Open down side trapdoor Insert completely the MicroSD Card into the slot marked (MicroSD) as indicated on the  gure. MicroSD Card must be back side positioned as indicated on marking.To remove the MicroSD Card push on it with touch panel pencil.Close down side trapdoor
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved224_7 Installing SIM for GPRS (optional)CAUTIONBefore starting, switch off the terminal by disconnecting the power supply.Open down side trapdoorInsert the SIM GPRS into the slot marked (SIM1) as indicated on the  gure. Take care to ensure that the SIM is inserted in the correct manner. The cut corner must be positioned as indicated on the  gure. Close down side trapdoor.WARNHINWEISBevor Sie beginnen, das Gerät auszuschalten, indem Sie das Netz.Cut corner
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved23Open down side trapdoorInsert the SAM Card into the slot marked (3) as indicated on the  gure. Take care to ensure that the SIM is inserted in the correct manner. The cut corner must be positioned as indicated on the  gure.Close down side trapdoor.Cut corner4_8 Installing SAM3 (optional)CAUTIONBefore starting, switch off the terminal by disconnecting the power supply.WARNHINWEISBevor Sie beginnen, das Gerät auszuschalten, indem Sie das Netz.
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved244_9 Installing 2nd SIM for GPRS (optional)CAUTIONBefore starting, switch off the terminal by disconnecting the power supply.Open down side trapdoornsert the SIM GPRS into the slot marked (SIM2) as indicated on the  gure. Take care to ensure that the SIM GPRS is inserted in the correct manner. The insertion position SIM corner (engraved on the terminal) must be located as shown on  gure.Do not force at the insertion. Once positioned the SIM GPRS is not fully inserted, this is normal.Close down side trapdoorCut cornerWARNHINWEISBevor Sie beginnen, das Gerät auszuschalten, indem Sie das Netz.Nicht mit Gewalt einzusetzen. Nach der Positionierung der GPRS-SIM-Karte wird den ganzen Weg, was normal ist nicht eingelegt.
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved255_Installing a paper rollYour terminal is supplied with one paper roll. When the paper roll is nearing the end, a red line will appear on the paper; this indicates that the paper roll must be replaced.CAUTIONUse only paper approved by the manufacturer (diameter 40 mm). Use of unsuitable paper is likely to damage the printer of your terminal (see paper characteristics at “Maintenance” chapter).Open the paper compartment by lifting the catch located at the rear of the terminal and drag the cover to the rear.CAUTIONDo not force the cover against the cables.WARNHINWEISNur vom Hersteller zugelassenes Papier benutzen (Durchmesser 40 mm). Durch den Einsatz von ungeeignetem Papier kann der Drucker des Terminals beschädigt werden (Siehe die Papierspezi kationen in Kapitel «Wartung»).WARNHINWEISDie Abdeckungen nicht gegen die Kabel drücken.
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved26Insert the paper roll in the compartment following the directions shown on the  gure below.Pull the paper up to the top of the terminal and hold it in this position.Maintain the paper and close the lid. Press the top of the lid in the centre as shown by arrow, until it clips into position.If you are inserting a new paper roll remove the  rst complete turn (this  rst turn of sensitive surface could be damaged during shipment).ADVICE
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved276_Daily use6_1 Keypad functionsNAVIGATION keysIngenico keyCANCEL key (red) CLEAR key (yellow) / Feed paper (long press) VALIDATION key (green) Dot key
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved286_2 Adjusting the contrast (B&W display only)No contrast management for the Color displayIf you wish to increase or to decrease the contrast of the characters displayed on screen, press simultaneously on the (dot key) and key to decrease the contrast, or the (dot key) and key to increase it. Keep pressing the keys as long as necessary.6_3 Card insertion6_3_1 Swiping a cardSwipe the card with constant speed, not too slowly not too fast, to maximize the reading ef ciency and avoid annoying repetitions.Insert the card manually in the driver, magstripe facing the main body of the terminal.6_3_2 Inserting a chip cardChip Cards should be inserted into your terminal as illustrated with the chip facing up and into the card reader.
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved296_3_3 Reading Contactless (Optional)Bring the card  rmly up to the active zone above (at about 1cm) the contactless logo located on paper trapdoor button.Keep the card close to the contactless logo during the transactionContactlessActive zoneYour contactless terminal provides four contactless status lights located on display/lens.When a contactless transaction is started the  rst (left hand) status light will be lit steadily; this indicates that the contactless is in use but a card is not being read.When a contactless card is presented to the contactless active zone (*) during a transaction the second, third and fourth status lights will be lit in turn. The card read is successful when all four status lights are lit and a con rmation tone can be heard.ContactlessStatus lights(*): Contactless Symbol is a trademark owned by and used with the permission of EMVCo, LLC.CAUTIONDo not stick any conductive label on to contactless active zone located on paper trapdoor button. It can decrease seriously contactless ef ciency.WARNHINWEISKeine leitende Etikett Kleben Sie nicht an kontaktlosen aktiven Zone auf Papier Falltür-Taste be ndet. Es kann ernsthaft kontakt Ef zienz verringern.
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved306_3_4 Headphone output (Optional)The headphone output jack is located under the card reader outlet. This option is not designed to play music, but to facilitate the use by blind people. 7_Maintenance / WartungCAUTIONBefore making any operations of maintenance in the terminal, make sure that the power supply is disconnected.7_1 Paper rollCharacteristics PrecisionsColour White58 mmWidthDiameter 40 mm max.The thermal paper can be deteriorated by poor storage conditions, so we recommend you to avoid:storage in hot wet places (near to air-conditioner, humidity higher than 85%)exposure to sunlight or ultraviolet for long periodsWARNHINWEISBevor irgendwelche Operationen der Wartung im Terminal, stellen Sie sicher, dass die Stromversorgung getrennt wird.Die Kopfhörerbuchse ist unter der Chipkartenleser entfernt. Diese Option ist nicht für die Musik zu spielen, aber nur, um die Verwendung von blinden Menschen zu erleichtern.contact with organic solvents (solvent type adhesive)
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved31direct contact with «diazo» papersdirect contact with waterRubbing or pressing the paper too stronglyCAUTIONIn order to benet from the complete guarantee of the product, use manufacturer approved thermal paper only.WARNHINWEISUm in den vollen Genuss der Garantie zu kommen, darf nur vom Hersteller zugelassenes wârmeempndliches Papier benutzt werden.7_2 Cleaning of the terminalFirst of all, unplug all the wires from the terminal.Good rules for proper cleaning of the terminal are:Use a soft cloth that is very slightly soaked with soapy water to clean the outside of the terminal. Manufacturer wipes kit is strongly recommended (ref: 296118801).Do not clean the electrical connections.CAUTIONDo not use in any case, solvents, detergents or abrasive products:Those materials might damage the plastic or electrical contacts.WARNHINWEISIn jedem Fall, verwenden Sie keine Lösungsmittel, Reinigungsmittel oder Scheuermittel: Diese Materialien können Kunststoff-oder elektrische Kontakte beschädigen.direct contact with materials containing plasticizers (PVC transparent folders or envelopes)
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved32Avoid exposing the terminal to the direct rays of the sun.Do not put anything into the slot of the smart card reader7_3 Transport and storageUse the original packaging for any unit or stored.Disconnect all cables from the terminal during the transport.7_4 TroubleshootingThe terminal does not turn on or does not connect to the telephone line Check the power supply and telephone line cables Check for electrical power network The terminal fails to establish a telephone connectionCheck that the tone of the phone line is freeCheck the conguration of the phone line and number to call Get support from technicalCards are not readCheck that the magnetic card is passed correctly (with magstripe facing the main body of the terminal) Swipe again the card with with constant speed, not too slow not too fast.Verify that the magnetic strip is not damaged, grooved or crackedMake sure you have inserted correctly the smart card into the smart card reader and removed the card only after the transactionThe ticket is not printedCheck the presence and proper positioning of the paper roll. Possibly adjust the paper roll following instructions present in this manual Check the type of paper used (thermal paper must be used) Verify thermal paper sensitive side.
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved337_5 Environment (WEEE, Batteries and Packaging)This product is labeled in accordance with European Directives 2002/96/EC concerning Waste Electrical and Electronic Equipment (WEEE) and 2006/66/EC concerning Batteries and Accumulators. Those provisions are requiring producers and manufacturers to become liable for take-back, treatment and recycling upon end of life of equipment and batteries.The associated symbol means that WEEE and waste batteries must not be thrown away but collected separately and recycled.Ingenico ensures that efcient collection and recycling schemes are set-up for WEEE and batteries according to the local regulation of your country. Please contact your retailers for more detailed information about the compliance solution in place for disposing of your old product and used batteries.Packaging waste must also be collected separately to assure a proper disposal and recycling. Please note that proper recycling of the electrical and electronic equipment and waste batteries will ensure safety of human health and environment8_MarkingsThe CE marking indicates terminal complies with harmonized standards and requirements of European Directives on:Radio and Telecommunications Terminal Equipment (R&TTE) RoHS (Restriction of Hazardous Substances)der europäischen Richtlinie über Funkanlagen und Telekommunikationsendeinrichtungen (R&TTE).der europäischen Richtlinie über die Beschränkung der Verwendung bestimmter gefährlicher Stoffe (RoHS).Dieses Produkt, mit der CE-Kennzeichnung , entspricht:
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved34This marking indicates that the product operates with an alternating current (AC) source (mains). It is completed by afferent values (voltage, frequency and max current).This marking indicates that your terminal is suitable for direct current (DC) only. It is completed by afferent values (voltage, and max current).Marking for Class II product. Such product does not require a safety connection to electrical earth.For Indoor use only.Output plug is Positive (+) and the barrel (ring) of the output plug is Negative (-)This marking indicates power supply meets limited power source safety requirements. This marking is apposed on to connector for telephone line connection.This marking is apposed on to connector for power supply output cable connection.This marking indicates power supply meets the energy ef ciency level VI requirements.
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved358_1 FCC/IC ComplianceThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct interference by one or more of the following measures :Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.Model NameModel : DESK/5000Eth/ModFCC ID IC NUMBERModel : DESK/5000CL/Eth/ModProduct : DESK/5000CL/Eth/Mod/Wi/BTProduct : DESK/3200CL/Eth/ModProduct : DESK/3500CL/Eth/ModFCC ID : XKB-D5000M00FCC ID : XKB-D5000M01FCC ID : XKB-D5000CLWIBTFCC ID : XKB-D3200CLFCC ID : XKB-D3500CLIC : 2586D-D5000M00IC : 2586D-D5000M01IC : 2586D-D5000CLWIBTIC : 2586D-D3200CLIC : 2586D-D3500CL
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved36(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operation.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :(1) l’appareil ne doit pas produire de brouillage, et(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.This device complies with FCC and ISED radiation exposure limits set forth for general population (uncontrolled exposure) in accordance with FCC rule part §2.1093, KDB447498 D01 and RSS-102 Issue 5 for portable use conditions.This device has been tested according to the RF exposure guidelines for typical hand-held operation in direct contact (0 cm distance) to the user’s hands and must not be collocated or operating in conjunction with any other antenna or transmitter.Cases with metal parts may change the RF performance of the device, including its compliance with RF exposure guidelines, in a manner that has not been tested or certied.Use of this device with an accessory in order to be worn and operated on user’s body is strictly prohibited and will invalidate the certications obtained for FCC and ISED.This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved37No changes shall be made to the equipment without the permission of Ingenico as this may void the user’s authority to operate the equipment.Cet appareil dans un mode portable de fonctionnement est conforme aux limites d’exposition RF générales des personnes dénies par FCC et ISED suivant les règles FCC part §2.1093 et KDB447498 D01 et RSS-102 Issue 5.Cet appareil a été testé selon les directives d’exposition RF pour une utilisation tenue en main typique en contact direct (0cm de distance) aux mains de l’utilisateur et ne doit pas être co-localisé ou utilisé en conjonction avec d’autres émetteurs.L’utilisation de cet appareil avec un accessoire dans le but d’être porté et utilisé sur le corps de l’utilisateur est strictement prohibé et invalidera les certications FCC et ISED obtenues.La limite DAS adoptée par les USA et le Canada est de 4,0 W/kg en moyenne sur 10 grammes de tissu. La valeur DAS la plus élevée signalée à la FCC et l’ISED pour ce type d’appareil est conforme à cette limite.Tout changement apporté à ce terminal non expressément approuvé par Ingenico est susceptible d’annuler le droit de l’utilisateur à se servir de cet équipement.The SAR limit adopted by USA and Canada is 4.0 W/kg averaged over 10 gram of tissue. The highest SAR value reported to FCC and ISED for this device complies with this limit.Le présent appareil est conforme aux spécications techniques applicables d’Innovation, Sciences et Développement économique Canada. L’indice d’équivalence de la sonnerie (IES) sert à indiquer le nombre maximal de dispositifs qui peuvent être raccordés à une interface téléphonique. La terminaison d’une interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que la somme des IES de tous les dispositifs n’excède pas cinq. L’IES pour cet appareil est de 0.1.This product meets the applicable Innovation, Science and Economic Development Canada technical specications. The Ringer Equivalence Number (REN) indicates the maximum number of devices allowed to be connected to a telephone interface. The termination of an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices not exceed ve. REN for this device is 0.1.
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved38Part 68 of FCC RulesModel NameModel : DESK/5000 Eth/ModUS MODEM Model : DESK/5000 CL/Eth/ModProduct : DESK/5000 CL/Eth/Mod/Wi/BTProduct : DESK/3200 CL/Eth/ModProduct : DESK/3500 CL/Eth/ModUS : IEOMM01BD5000M00US : IEOMM01BD5000M01US : IEOMM01BD5000M01US : IEOMM01BD3200CLUS : IEOMM01BD3500CLThe device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. In addition, high-power radars are allocated as primary users (i.e. priority users) of the bands 5250–5350 MHz and 5650–5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés uniquement pour une utilisation à l’intérieur an de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux. D’autre part, les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) des bandes de 5250 à 5350 MHz et de 5650 à 5850 MHz et, d’autre part, que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs de RL-EL.
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reserved39If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualied installer.U.S.A service center: Ingenico North America3025 Windward Plaza, suite 600Alpharetta, GA 30005USAThis equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identier in the format US : AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.This equipment uses the following USOC jacks : (RJ11C).A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed ve (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible.Also, you will be advised of your right to le a complaint with the FCC if you believe it is necessary.The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of this equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modications to maintain uninterrupted service.If trouble is experienced with this equipment, please contact INGENICO, or your local INGENICO distributor or service center in the U.S.A. for repair and/or warrant information.Tel: +1(678) 456 1200Fax: +1 (678) 456 1201Email: info.us@ingenico.com
Desk Series900024281 R11 000 07/0217Copyright© 2017 IngenicoAll rights reservedwww.ingenico.com28-32, boulevard de Grenelle, 75015 Paris - France / (T) +33 (0)1 58 01 80 00 / (F) +33 (0)1 58 01 91 35Ingenico - SA au capital de 47 656 332 / 317 218 758 RCS Nanterre 40“This Document is Copyright © 2017 by INGENICO Group. INGENICO retains full copyright ownership, rights and protection in all material contained in this document. The recipient can receive this document on the condition that he will keep the document condential and will not use its contents in any form or by any means, except as agreed beforehand, without the prior written permission of INGENICO. Moreover, nobody is authorized to place this document at the disposal of any third party without the prior written permission of INGENICO. If such permission is granted, it will be subject to the condition that the recipient ensures that any other recipient of this document, or information contained therein, is held responsible to INGENICO for the condentiality of that information. Care has been taken to ensure that the content of this document is as accurate as possible. INGENICO however declines any responsibility for inaccurate, incomplete or outdated information. The contents of this document may change from time to time without prior notice, and do not create, specify, modify or replace any new or prior contractual obligations agreed upon in writing between INGENICO and the user. INGENICO is not responsible for any use of this device, which would be non-consistent with the present document.All trademarks used in this document remain the property of their rightful owners.”Your contact

Navigation menu