IDP SMART-30D Card Printer User Manual CE FCC

IDP Corp., Ltd. Card Printer CE FCC

User Manual

1 User Manual SMART-30S, SMART-30R, SMART-30D, SMART-50S, SMART-50D, SMART-50L SMART Series
2 Copyright Notice Users must respect the copyright laws applicable in their country. This manual must not be photocopied, translated, reproduced or transmitted in whole or in part for any reason and by the means that might be, albeit electronic or mechanical, without the express, written authorization of the company IDP card printer. All information contained herein may be subject to modification without prior notice. IDP card printer accepts no liability for any possible errors herein, nor for any accidental damage or damage caused through the dissemination or the use of this manual. Trademarks SMART-50 is a trademark and IDP is a registered trademark of IDP card printer. Windows is registered trademarks of Microsoft Corp. All other trademarks or registered trademarks are marks of their respective holders. SMART-50 Design is a trademark of IDP. Return Materials Authorization In order to make a warranty claim you must contact an IDP Reseller. You will be responsible for packaging the printer for shipment and the costs of shipping and insurance of the printer from the point of use of the printer to the IDP Reseller. The IDP Reseller will bear the costs of shipping and insuring the printer from the repair location to the address from which the printer was shipped. Before returning any equipment for in-warranty or out-of warranty repair, contact an IDP Reseller or an IDP Service Center for a Return Materials Authorization (RMA) number. Repack the equipment in the original packing material and mark the RMA number clearly on the outside of the box. For more information about RMA or IDP warranty statements, refer to the Warranty booklet on the quick install guide.
3 Table of Contents 1. Introduction ........................................................................ 7 1.1 Printer outside features ........................................................................... 7 1.1.1 SMART-30 outside feature. ...................................................................... 7 1.1.2 SMART-50 outside feature. ...................................................................... 8 1.2 Printer inside features .................................................................................. 11 1.2.1 SMART-30 inside feature. ..................................................................... 11 1.2.2 SMART-50 inside feature. ..................................................................... 12 1.3 Ribbon cartridge features ............................................................................. 13 1.4 LCD panel display & button operation ......................................................... 14 2. Printer installation .............................................................. 18 2.1. Fitting the ribbon ......................................................................................... 18 2.2. Loading the cards ........................................................................................ 21 2.3. The withdrawal of printed cards. ................................................................. 23 2.4. Driver installation (Windows XP, 2000, 2003) .............................................. 24 2.5. Driver installation (Windows Vista, 7, 8) ...................................................... 31 2.5. Network configuration ................................................................................. 37 3. Driver configuration ........................................................... 46 3.1. Checking printer properties ........................................................................ 46 3.2. Changing printer properties ........................................................................ 46 3.3. Other settings .............................................................................................. 51 4. Utilities ............................................................................... 54 4.1. Card Printer Setup ....................................................................................... 54 4.2. Card Printer Test ......................................................................................... 64 4.3. Firmware upgrade ....................................................................................... 70 5. Optional device driver installation ..................................... 73 5.1. Contact smartcard reader ............................................................................ 73 6. Troubleshooting ................................................................. 78 6.1. Cleaning the printer ..................................................................................... 78 6.2 TPH (Thermal Print Head) replacement ........................................................ 82 6.3. Card movement ........................................................................................... 83 6.4. Printing quality ............................................................................................ 84 6.5. Magnetic stripe encoding ............................................................................ 85 6.6. General operation ........................................................................................ 85 7. Printer specification ........................................................... 87
4 Table of Pictures Pic.1 SMART-30 front features .............................................................................................. 7 Pic.2 SMART-30 back features .............................................................................................. 7 Pic.3 SMART-50 front features .............................................................................................. 9 Pic.4 SMART-50 rear features ............................................................................................... 9 Pic.5 SMART-50S ................................................................................................................ 10 Pic.6 SMART-50D ................................................................................................................ 10 Pic.7 SMART-50L ................................................................................................................. 10 Pic.8 SMART-30 Inside features .......................................................................................... 11 Pic.9 SMART-50 Inside features .......................................................................................... 12 Pic.10 Ribbon cartridge features ........................................................................................ 13 Pic.11 Top Cover open ........................................................................................................ 18 Pic.12 Take out the ribbon cartridge ................................................................................... 18 Pic.13 Loading the ribbon 1 ................................................................................................ 19 Pic.14 Loading the ribbon 2 ................................................................................................ 19 Pic.15 Installing the cleaning roller .................................................................................... 19 Pic.16 Peeling the protective wrapper ................................................................................ 19 Pic.17 Installing the ribbon cartridge .................................................................................. 20 Pic.18 Close Top Cover ....................................................................................................... 20 Pic.19 Adjusting the card thickness lever .......................................................................... 21 Pic.20 Preparing the card 1 ................................................................................................. 21 Pic.21 Preparing the card 2 ................................................................................................. 21 Pic.22 Loading the cards 1 ................................................................................................. 22 Pic.23 Loading the cards 2 ................................................................................................. 22 Pic.24 Loading the cards 3 ................................................................................................. 22 Pic.25 Loading the cards 4 ................................................................................................. 22 Pic.25 SMART-30 Stacker ................................................................................................... 23 Pic.25 SMART-50 Stacker ................................................................................................... 23 Pic.26 Install XP printer driver 1 ......................................................................................... 24 Pic.27 Install XP printer driver 2 ......................................................................................... 24 Pic.28 Install XP printer driver 3 ......................................................................................... 24 Pic.29 Install XP print driver 4 ............................................................................................. 24 Pic.30 Install XP print driver 5 ............................................................................................. 25 Pic.31 Install XP print driver 6 ............................................................................................. 25 Pic.32 Install XP printer driver 7 ......................................................................................... 25 Pic.33 Install XP printer driver 8 ......................................................................................... 25 Pic.34 Install XP printer driver 9 ......................................................................................... 26 Pic.35 Install XP printer driver 10 ....................................................................................... 26 Pic.36 Install XP printer driver 11 ........................................................................................ 26 Pic.37 Install XP printer driver 12 ....................................................................................... 27 Pic.38 Install XP printer driver 13 ....................................................................................... 27 Pic.39 Install XP printer driver 14 ....................................................................................... 27 Pic.40 Install XP printer driver 15 ....................................................................................... 27 Pic.41 Install XP printer driver 16 ....................................................................................... 28 Pic.42 Install XP printer driver 17 ....................................................................................... 28 Pic.43 Install XP printer driver 18 ....................................................................................... 28 Pic.44 Install XP printer driver 19 ....................................................................................... 29 Pic.45 Install XP printer driver 20 ....................................................................................... 29 Pic.46 Install XP printer driver 21 ....................................................................................... 29 Pic.47 Install XP printer driver 22 ....................................................................................... 29 Pic.48 Install XP printer driver 23 ....................................................................................... 30
5 Pic.49 Install XP printer driver 24 ....................................................................................... 30 Pic.50 Install XP printer driver 25 ....................................................................................... 30 Pic.51 Install Win7 driver 1 ................................................................................................. 31 Pic.52 Install Win7 driver 2 ................................................................................................. 31 Pic.53 Install Win7 driver 3 ................................................................................................. 31 Pic.54 Install Win7 driver 4 ................................................................................................. 31 Pic.55 Install Win7 driver 5 ................................................................................................. 32 Pic.56 Install Win7 driver 6 ................................................................................................. 32 Pic.57 Install Win7 driver 7 ................................................................................................. 32 Pic.58 Install Win7 driver 8 ................................................................................................. 32 Pic.59 Install Win7 driver 9 ................................................................................................. 33 Pic.60 Install Win7 driver 10 ................................................................................................ 33 Pic.61 Install Win7 driver 11 ................................................................................................ 33 Pic.62 Install Win7 driver 12 ................................................................................................ 33 Pic.63 Install Win7 driver 13 ................................................................................................ 34 Pic.64 Install Win7 driver 14 ................................................................................................ 34 Pic.65 Install Win7 driver 15 ................................................................................................ 34 Pic.66 Install Win7 driver 16 ................................................................................................ 35 Pic.67 Install Win7 driver 17 ................................................................................................ 35 Pic.68 Install Win7 driver 18 ................................................................................................ 35 Pic.69 Install Win7 driver 19 ................................................................................................ 35 Pic.70 Install Win7 driver 20 ................................................................................................ 36 Pic.71 Install Win7 driver 21 ................................................................................................ 36 Pic.72 Install Win7 driver 22 ................................................................................................ 36 Pic.73 Install Win7 driver 23 ................................................................................................ 36 Pic.74 Rear view of SMART-50 printer 1 ............................................................................. 37 Pic.75 Rear view of SMART-50 printer 2 ............................................................................. 37 Pic.76 Running the NetAdmin ............................................................................................. 38 Pic.77 Network printer is not found .................................................................................... 38 Pic.78 Connecting to USB port ........................................................................................... 39 Pic.79 NetAdmin Log-in ...................................................................................................... 39 Pic.80 Dynamic IP configuration ......................................................................................... 40 Pic.81 Static IP configuration.............................................................................................. 40 Pic.82 Network service configuration ................................................................................. 41 Pic.83 OCP configuration .................................................................................................... 41 Pic.84 Network user configuration ..................................................................................... 42 Pic.85 USB port state .......................................................................................................... 42 Pic.86 Rebooting the network module ................................................................................ 43 Pic.87 Reset to default ........................................................................................................ 43 Pic.88 Upgrading the firmware 1 ......................................................................................... 44 Pic.89 Upgrading the firmware 2 ......................................................................................... 44 Pic.90 Upgrading the firmware 3 ......................................................................................... 45 Pic.91 Printer properties 1 .................................................................................................. 46 Pic.92 Printer properties 2 .................................................................................................. 46 Pic.93 Layout ...................................................................................................................... 47 Pic.94 Advanced Setup ....................................................................................................... 48 Pic.95 Paper / Ribbon / Printing .......................................................................................... 49 Pic.96 Side / Media .............................................................................................................. 50 Pic.97 Laminator ................................................................................................................. 50 Pic.98 Printer sharing ......................................................................................................... 51 Pic.99 Ports ......................................................................................................................... 51 Pic.100 Advanced ............................................................................................................... 52 Pic.101 Color Management ................................................................................................. 52 Pic.102 Service .................................................................................................................... 52 Pic.103 Laminator ............................................................................................................... 53
6 Pic.104 CardPrinterSetup Log-in ........................................................................................ 54 Pic.105 CardPrinterSetup start ........................................................................................... 54 Pic.106 CardPrinterSetup – Card Printer Basic Setup ........................................................ 55 Pic.107 SMART-30 R density ............................................................................................... 56 Pic.108 Color density .......................................................................................................... 57 Pic.109 Resin Black density................................................................................................ 57 Pic.110 Overlay density....................................................................................................... 57 Pic.111 CardPrinterSetup – Card Printer Advanced Setup ................................................. 59 Pic.112 CardPrinterSetup – Laminator Basic Setup ........................................................... 61 Pic.113 CardPrinterSetup – Laminator Advanced Setup .................................................... 62 Pic.114 CardPrinterTest ...................................................................................................... 64 Pic.115 Magnetic stripe encoding ....................................................................................... 66 Pic.116 Contact smartcard encoding .................................................................................. 67 Pic.117 Contactless smartcard encoding ........................................................................... 68 Pic.118 Upgrading printer firmware .................................................................................... 70 Pic.119 Ready for firm-ware upgrade .................................................................................. 71 Pic.120 Firm-ware manual upgrade .................................................................................... 71 Pic.121 Ready for laminator firm-ware upgrade ................................................................. 72 Pic.122 Firm-ware manual upgrade .................................................................................... 72 Pic.123 Contact smartcard reader driver installation ......................................................... 73 Pic.124 License agreement ................................................................................................. 74 Pic.125 Installing the contact smartcard reader driver....................................................... 74 Pic.126 Completing the smartcard reader driver installation ............................................. 75 Pic.127 Found New Hardware Wizard ................................................................................. 76 Pic.128 Installation method selection ................................................................................. 76 Pic.129 Driver location ........................................................................................................ 77 Pic.130 Completing the driver installation .......................................................................... 77 Pic.131 Exclusive cleaning card for SMART-50 printer ...................................................... 78 Pic.132 Printer cleaning start .............................................................................................. 78 Pic.133 Printer cleaning Step 1 ........................................................................................... 79 Pic.134 Printer cleaning Step 2 ........................................................................................... 79 Pic.135 Printer cleaning Step 3 ........................................................................................... 80 Pic.136 Printer cleaning Step 4 ........................................................................................... 80 Pic.137 Printer cleaning Step 5 ........................................................................................... 81 Pic.138 Printer cleaning Step 6 ........................................................................................... 81 Pic.139 Thermal Print Head ................................................................................................ 82 Pic.140 Print head setup ..................................................................................................... 82 Pic.141 Print head replacement .......................................................................................... 83 Pic.142 Print head angle ..................................................................................................... 83 Pic.142 Printing quality trouble 1 ........................................................................................ 84 Pic.143 Printing quality trouble 2 ........................................................................................ 84 Pic.144 Printing quality trouble 3 ........................................................................................ 84 Pic.145 Printing quality trouble 4 ........................................................................................ 85 Pic.146 Printing quality trouble 5 ........................................................................................ 85 Pic.148 Printer Specification 1 ............................................................................................ 87 Pic.149 Printer Specification 2 ............................................................................................ 89 Pic.150 Printer Specification 3 ............................................................................................ 90
7 1. Introduction 1.1 Printer outside features 1.1.1 SMART-30 outside feature. For the user’s convenience, SMART-30 status can be seen through LED and the printer can be controlled by a button. It takes a power via the 24V adaptor provided with the printer. Using USB and Network port, it is communicated with the user’s PC The following shows the outside functional features found on the printer. There are five models in SMART-50 card printer series such as SMART-50S, SMART-50D, SMART-50L. ① ② ③ ④ ⑤ ①Top cover open button ②External contactless Smartcard encoding position ③Input hopper ④LED buttons ⑤Dividing Stacker Pic.1 SMART-30 front features ⑥ ⑦ ⑧ ⑨ ①Backside card outlet ②Power switch ③24V power connector ④Network port In case there is no network option, it is closed. ⑤USB port ⑩ Pic.2 SMART-30 back features
8 SMART-30S (Pic.5) is the standard card printer. It can be printed in single side with the encoding. This manual is prepared based on SMART-30S. SMART-30R (Pic.6) is the rewritable card printer. It can rewrite on rewritable card in single side with encoding. SMART-30D (Pic.7) have a flipper which can enable to print in both side. SMART-30D can print the both side of the card with the encoding. Pic.3 SMART-30S (Standard) Pic.4 SMART-30R (Rewritable) Pic.5 SMART-30D (Dual) 1.1.2 SMART-50 outside feature. For the user’s convenience, SMART-50 status can be seen through LCD with LED and the printer
9 can be controlled by two LED buttons. It takes a power via the 24V adaptor provided with the printer. Using USB and Network port, it is communicated with the user’s PC The following shows the outside functional features found on the printer. Pic.6 SMART-50 front features Pic.7 SMART-50 rear features ① ② ③ ④ ⑤ ⑥ ⑦ ①Top cover open button ②External contactless Smartcard encoding position ③Fan ④Input hopper ⑤LED buttons ⑥LCD show the process status ⑦Internal SIM reader ⑧ ⑨ ⑩ ⑪ ⑥Backside card outlet ⑦Power switch ⑧24V power connector ⑨Network port In case there is no network option, it is closed. ⑩USB port ⑫
10 There are five models in SMART-50 card printer series such as SMART-50S, SMART-50D, SMART-50L. SMART-50S (Pic.5) is the standard card printer. It can be printed in single side with the encoding. This manual is prepared based on SMART-50S. SMART-50D (Pic.6) have a flipper which can enable to print in both side. SMART-50D can print the both side of the card with the encoding. SMART-50L (Pic.7) produces long-life cards for ID and access control with customizable security features and ability to print smart cards. To cater to expanding requirement in card security, SMART-50L’s DLW(Direct to Laminating in a Wink) technology provides the most stable & fast laminating solutions. Pic.8 SMART-50S Pic.9 SMART-50D Pic.10 SMART-50L
11 1.2 Printer inside features 1.2.1 SMART-30 inside feature. In SMART-30 printer, the ribbon is installed by a ribbon cartridge which can be used semipermanently. The following shows the inside functional features found on your SMART-30 printer. Pic.11 SMART-30 Inside features ① Output hopper(Stacker) Collect the printed card and/or encoded cards. ② Input hopper Load the cards for printing. ③ Card thickness control lever Adjust the cards thickness. ④ Ribbon cartridge Install the ribbon and the disposable cleaning roller. ⑤ Thermal Print Head This enables the cards to be printed. (Caution!: This is very hot after printing. Do not contact the surface of the Thermal Print Head with fingers or a sharp metal object to avoid degrading print quality or damaging printer head permanently.) ① ② ③ ④ ⑤
12 1.2.2 SMART-50 inside feature. In SMART-50 printer, the ribbon is installed by a ribbon cartridge which can be used semipermanently. The following shows the inside functional features found on your SMART-50 printer. Pic.12 SMART-50 Inside features ② Output hopper(Stacker) Collect the printed card and/or encoded cards. ② Input hopper Load the cards for printing. ③ Card thickness control lever Adjust the cards thickness. ④ Ribbon cartridge Install the ribbon and the disposable cleaning roller. ⑤ Thermal Print Head This enables the cards to be printed. (Caution!: This is very hot after printing. Do not contact the surface of the Thermal Print Head with fingers or a sharp metal object to avoid degrading print quality or damaging printer head permanently.) ⑥ External contactless encoder Contactless smartcard encoder. ① ② ③ ④ ⑤ ⑥ ①Output hopper ②Input hopper ③Card thickness control lever ④Ribbon cartridge ⑤Thermal Print Head ⑥External contactless encoder
13 1.3 Ribbon cartridge features Pic.13 Ribbon cartridge features ① Ribbon cartridge -. Install a ribbon and a disposable cleaning roller provided with the ribbon. -. In the case of SMART-30 R model, a ribbon is not used, and a disposable cleaning roller is only installed and used. -. This semi-permanent ribbon cartridge is a component of the printer. Printer does not operate if it is broken or damaged. In this case, please contact printer reseller. ② ③ Take up & Supply parts -. Ribbon is wrapped to the supply parts as the Pic. 10. It should be installed as the Pic.10. ④ Disposable cleaning roller -. It removes dust on the surface of card to improve print quality before the card is printed. It should be changed together with the ribbon. -. After installing the disposable cleaning roller to the ribbon cartridge, peel off the protective film. -. It is provided with the ribbon. -. In the case of SMART-30 R model, you have to purchase the disposable cleaning roller from the reseller. ① ② ③ ④ ①Ribbon cartridge ②Take up parts ③Supply parts ④Disposable cleaning roller
14 1.4 LCD panel display & button operation SMART-50 printer can show the real-time process status to user. SMART-30’s status is displayed in windows tray. No LCD Display LED Button State Description Left Right Left Right 1 Ver X.XX… Initialize… On On Initializing Initializing with the indication of SMART-50 firmware version 2 INIT Error xx <Replay Replay> Blinking Blinking Repeat Repeat Error during initializing Showing error no. in case of failure of normal initializing while SMART-50 is initialized. (Refer to page13). Press any keys for re-initializing process. 3 S m a r t Auto Ribbon Set On On Automatic ribbon setting It optimizes the ribbon position setting automatically in case of the replacement of color ribbon(YMCKO or YMCKOK). 4 Auto Ribbon Set Fail!!!! Blinking Blinking Fail to optimize the ribbon setting Display these messages when the auto ribbon setting is failed and it shows the ribbon detecting level. 5 Auto Ribbon Set Color=xxx(xxx) Blinking Blinking Fail to optimize the ribbon setting and display the ribbon’s color value 6 S M A R T System Ready On On Installed ribbon informationSoft power ON/OFF Standby Printer is ready for printing and you can check the installed ribbon information by pressing the left button. Printer turns off by pressing the right button. Printer turns on by pressing the right button when it turns off. 7 Wait.. 1”C Temperature=xxx Blinking Blinking Printer’s operating temperature is under 1℃ Shown it when printer’s operating temperature falls down under 1℃. Normal operating temperature is 15℃~35℃. 8 S m a r t Unlock Please.. On On Printer is locked Physical key option is active using the CardPrinterSetup utility and it shows the locked state. Unable to print. 9 S m a r t Verify your PC On On PC is not authenticated Authentication option is active using the CardPrinterSetup utility. When use the printer with an unauthenticated PC, it is shown. Printer is not working. 10 Ribbon Balance Type / Remains On On Card out Display the ribbon type and remains Display the installed ribbon’s type and the remains. It can be shown by pressing the left LED button on the system ready mode. 11 S M A R T Printing! On On Printing Under printing.
15 No LCD Display LED Button State Description Left Right Left Right 12 S M A R T Mag R/W On On Reading or writing the Magnetic stripe Magnetic encoder is reading or writing the magnetic stripe information. 13 Spool Error! <-Any Key Push-> Blinking Blinking Cancel & Initialize Cancel & Initialize Printing data is not transmitted properly Shown it when error occurs in a printing data transmission. Press any keys to delete the spooled data and to return the ready state. 14 Print Error xx <Replay Cancel> Blinking Blinking Repeat Cancel & Initialize Error in printing or moving a card Error in the printing or the transmission. Retry by pressing the left button or cancel the command by pressing the right button. 15 Top Cover Open <-Card Moving -> Blinking Blinking Move a card to the back side Move a card to the front side Top cover open Top cover is open. The card in the printer can be moved by pressing the left or right LED button. If press both buttons at the same time, the print head will be up and down. (Flipper will be flip over if it is installed) 16 Check Please.. Ribbon Not Found Blinking Blinking Ribbon redetecting Ribbon redetecting There is no ribbon in the printer or fail to detect Fail to detect the ribbon. Check the ribbon installed state. If there is no ribbon, install the ribbon. If there is a ribbon, pull out it and install again. Press the left or right button to redetect the ribbon. 17 Check Please.. Ribbon Zero Blinking Blinking Ribbon redetecting Ribbon redetecting The installed ribbon has run out It is displayed when the installed ribbon is all used up. Replace with new ribbon. Press the left or right button to redetect the ribbon. 18 Check Please.. TPH Not Found Blinking Blinking Thermal Print head is not installed Thermal Print Head is not installed or there is a misconnection of the cable. Open the top cover to check the print head installed state or turn off the printer and check the cable connecting state. 19 Print Error xx Top Cover Open Blinking Blinking Fail to move the card out(Check the card in the printer) The card in the printer will be come out when the initialization or top cover close. If it is not come out, this message will be displayed. Remove the card and close the top cover. 20 Card Out Error <Replay Cancel> Blinking Blinking Repeat Cancel & Initialize Fail to move the card out(Check the card in the printer) After an error occurs in printing, the error card is not come out even though "Replay" or "Cancel" button is pressed. 21 S M A R T Download... On On Firmware downloading The printer is downloading the firmware. Do not turn off the power until it is rebooting. It takes about 20 seconds. 22 Board Test Mode Wait Test mode state Test mode which can test the sensors or motors of the printer. User can set the LED status. Table1 Status display
16 Description of printer error code Error code Description 0 Card in error 1 Card move center error 2 Card out error 3 Card move magnetic error 4 Card move contact encoder error 5 Card move contactless encoder error 6 Card move error from the printer to the flipper 7 Card move error form the flipper to the printer 8 Print head up error 9 Print head down error 10 IC Contactor up 11 IC Contactor down 12 Flipper top error 13 Flipper bottom error 14 Error in printing 15 Magnetic stripe read/write error 16 Ribbon search error 17 Ribbon move error 18 No print head installed 19 Print head overheating 20 No ribbon 21 Printing data error 22 Card back out error 23 Magnetic data erasing error 24 Printer password is not correct 25 Magnetic stripe track 1 read error 26 Magnetic stripe track 2 read error 27 Magnetic stripe track 3 read error 28 Printer locked state 29 Printer spool full state 30 No defined 31 No defined
17 Description of laminator error code Error code Description 0 Laminator head up error 2 Laminator head down error 4 Laminator card in error 6 Laminator card move error 8 Laminator card front out error 9 Laminator card rear out error 10 Flipper error 13 Error while laminating 15 Laminator initializing error 16 Laminator film zero error 17 Laminator film search error 31 No laminating film
18 2. Printer installation 2.1. Fitting the ribbon Before printing, prepare the related items such as a card, a ribbon and a cleaning roller. In this section we invite you to know the proper method of installing the ribbon and the cleaning roller into the printer. In the case of SMRT RW model, the ribbon is no needed so skip 2.1.4 and 2.1.5 process. 2.1.1. Turn off the printer Pic.14 Top Cover open 2.1.2. Open the printer top cover by pressing the top cover open button. Pic.15 Take out the ribbon cartridge 2.1.3. Take out the ribbon cartridge.
19 Pic.16 Loading the ribbon 1 2.1.4. Install a ribbon into the ribbon cartridge as left Pic. 13. Pic.17 Loading the ribbon 22.1.5. Insert the supply side of the ribbon to no.1 hole and press the opposite (no.2). Insert the take-up side of the ribbon same method to no.3 and no.4. After inserting, tighten the ribbon. (Caution! If the ribbon is not tightened, a rolling up error might be happened.) Pic.18 Installing the cleaning roller 2.1.6. Install the disposable cleaning roller to the ribbon cartridge. Pic.19 Peeling the protective wrapper 2.1.7. Peel the protective wrapper from the cleaning roller. After removing the protective wrapper, the cleaning roller should be kept clean from fingerprints, dust and foreign substances to avoid contamination because it is adhesive. (Caution! Do not use without peeling off the protective wrapper because the cleaning roller cannot perform its function.) ① ② ③ ④
20 Pic.20 Installing the ribbon cartridge 2.1.8. Install the ribbon cartridge into the printer after installing the ribbon with a cleaning roller to the cartridge. Pic.21 Close Top Cover 2.1.9. Close the top cover (If it is not closed properly, check the installation state of the ribbon cartridge.)
21 2.2. Loading the cards This section shows how to load the plastic cards. Pic.22 Adjusting the card thickness lever 2.2.1. Open the input hopper cover. 2.2.2. Adjust the card thickness with the card thickness control lever. (Caution! If the adjustment is not correct, it will make some error. Use the type of cards in the specification of this manual. Always keep the card surface clean state.) Pic.23 Preparing the card 1 Pic.24 Preparing the card 2 2.2.4. To separate cards from each other, push a stack of cards back and forth to an angle about 45 degreesvertically. (Static charge makes cards stuck with significant adhesive force. These cards must be physically separated from each other before inserted into the feeder. If not separated, feeding or printing problems may occur.)
22 Pic.25 Loading the cards 1 2.2.5. Stand the stack of cards vertically after separating. Pic.26 Loading the cards 2 2.2.6. Load the cards on the input hopper properly and close the hopper cover. Pic.27 Loading the cards 3 2.2.7. When insert each one card, insert the card to the end as the Pic. 24and 25. Pic.28 Loading the cards 4
23 2.3. The withdrawal of printed cards. Printed cards are passed out to the stacker of rear bottom side of SMART printer. SMART-30’s stacker can be divided as following image. Pic.29 SMART-30 Stacker SMART-50’s stacker sticks out of the device so you can withdraw the printedcards easily. Pic.30 SMART-50 Stacker
24 2.4. Driver installation (Windows XP, 2000, 2003) Pic.31 Install XP printer driver 1 2.4.1. Insert the installation CD provided with the printer. 2.4.2. Choose the language and click “Driver Install”. Pic.32 Install XP printer driver 2 Pic.33 Install XP printer driver 3 2.4.3. STEP 1: If the printer is connected to the PC and turned on, turn off the power of the printer. Click “Next”. The existing installed printer driver will be removed. If the printer driver is already installed, it will be removed automatically but it may take times. Choose the language as shown on the Pic.29and 27. Pic.34 Install XP print driver 4
25 Pic.35 Install XP print driver 5 2.4.4. STEP 2: Click “Next” to ready the installation of the printer driver. Pic.36 Install XP print driver 6 2.4.5. If there is a pop-up window for the software installation, click “Continue Anyway”. Pic.37 Install XP printer driver 7 2.4.6. STEP 3: Click “Next” to use USB port. Click “TCP/IP Network port” to use the printer as network printer and choose the printer as shown on the Pic.34. (If there is no information on the window for the network printer list, it means that the printer is not connected to the network. Check “2.5 Network Printer” section.) Pic.38 Install XP printer driver 8
26 Pic.39 Install XP printer driver 9 2.4.7. Please connect a power supply to the printer. (For the network printer, refer to “2.5 Network Printer” section.) Pic.40 Install XP printer driver 10 2.4.8. Please connect USB cable provided with the printer to PC and the printer. (For the network printer, refer to “2.5 Network Printer” section.) Pic.41 Install XP printer driver 11 2.4.9. Turn on the printer to boot up it.
27 Pic.42 Install XP printer driver 12 2.4.10. Select “Install the software automatically (Recommended)”and click “Next”. Pic.43 Install XP printer driver 132.4.11. Click “Continue Anyway” in Software Installation window. Pic.44 Install XP printer driver 14 2.4.12. Click “Finish” in Completing the Found New Hardware Wizardwindow. Pic.45 Install XP printer driver 15 2.4.13. When the printer driver installation is completed. Click “Close”.
28 Pic.46 Install XP printer driver 16 2.4.14. Check “IDP SMART-50 Card Printer” is generated in Printers and Faxes window. Pic.47 Install XP printer driver 17 2.4.15. After selecting the icon of “IDPSMART-50 Card Printer”, click the right mouse button and select the “Properties”. Pic.48 Install XP printer driver 18 2.4.16. Select “General” tap and click “Print Test Page” button on the IDPSMART-50 Card Printer Properties window.
29 Pic.49 Install XP printer driver 19 2.4.17. Printer will start the printing and there will be the window which asks the printing success. If the printing is normal, click the “OK” (If the printing is abnormal or the printer error is occurred, remove the problem refer to “Trouble Shooting” section and execute test printing again.) Pic.50 Install XP printer driver 20 2.4.18. Please install “Smart Application” program after installing the printer driver. Pic.51 Install XP printer driver 21 2.4.19. Click “Next” on the “Smart Applications - InstallShield Wizard” window. Pic.52 Install XP printer driver 22 2.4.20. Select “I accept the terms of the license agreement” and click “Next”.
30 Pic.53 Install XP printer driver 23 2.4.21. Choose the destination location and click “Next”. Pic.54 Install XP printer driver 24 2.4.22. Click “Install” to begin the installation. Pic.55 Install XP printer driver 25 2.4.23. Smart Design/DB program is installed successfully.
31 2.5. Driver installation (Windows Vista, 7, 8) Pic.56 Install Win7 driver 1 2.5.1. Please insert the installation CD. 2.5.2. Please choose language and click“Driver Install”. Pic.57 Install Win7 driver 2 2.5.3. When “User Account Control”window is opened, click “Yes” Pic.58 Install Win7 driver 3 Pic.59 Install Win7 driver 4 2.5.4. STEP 1: Please turn off printer if it isconnected to PC. Please click“Next”. When you click “Next”, older driverwill be removed automatically. This process will take several minutes toremove older driver. You can select the languages by selecting thecombo box as shown on the Pic.55.
32 Pic.60 Install Win7 driver 5 Pic.61 Install Win7 driver 6 2.5.5. STEP 2: When you click “Next”, the driver installation will be ready. Pic.62 Install Win7 driver 7 2.5.6. Please click “Install this driver software anyway” in case “Windows Security” window comes out. Pic.63 Install Win7 driver 8 2.5.7. STEP 3: Please click “Next” if printer is connected to USB only. If you want to install the driver for a printer connected to network, please select the “TCP/IP Network port” and select the proper printer as shown on the Pic.60. (If no printer comes out on the window, please check the connection. Please refer “2.5 Network Printer Setup”.)
33 Pic.64 Install Win7 driver 9 Pic.65 Install Win7 driver 10 2.5.8. Please connect a power supply to the printer. (If your printer is for network, please refer “2.5 Network Configuration”.) Pic.66 Install Win7 driver 11 2.5.9. Please connect USB cable to theprinter. (If your printer is for network, please refer “2.5 Network Configuration”.) Pic.67 Install Win7 driver 12 2.5.10. Please turn on the printer.
34 Pic.68 Install Win7 driver 13 2.5.11. When driver installation is completed, please click “Close”. Pic.69 Install Win7 driver 14 2.5.12. Please open “Devices and Printers” from “Hardware and Sound”. Please check if “IDPSMART-50 Card Printer” is created. Pic.70 Install Win7 driver 15 2.5.13. Please click the right mouse button after cursor is placed on “IDPSMART-50 Card Printer” icon. Click “Printer properties”.
35 Pic.71 Install Win7 driver 16 2.5.14. Please select “general” tab and click “Printer test page” in “IDPSMART-50 Card Printer Properties”window. Pic.72 Install Win7 driver 17 2.5.15. Please check test card if it is printed properly and click “Close” if a card is printed properly. (If card is not printed or error comes out, please refer “Trouble Shooting”.) Pic.73 Install Win7 driver 18 2.5.16. Please install “Smart Design/DB”by clicking “Smart Design/DB Installation”. Pic.74 Install Win7 driver 19 2.5.17. Please click “Next” when “Smart Application Install Shield Wizard”comes out.
36 Pic.75 Install Win7 driver 20 2.5.18. Please agree “I accept the terms of the license agreement” and click “Next”. Pic.76 Install Win7 driver 21 2.5.19. Please select directory for program installation and click “Next”. Pic.77 Install Win7 driver 22 2.5.20. Please click “Installation”. Pic.78 Install Win7 driver 23 2.5.21. Please click “Finish”.
37 2.5. Network configuration 2.5.1 Connecting network port Pic.79 Rear view of SMART-50 printer 1 The printer which installed withnetwork option has a port for networkconnection as shown in the Pic.76 - ③. ① Power Switch ② Power Supply Connector ③ Network Port ④ USB Port Pic.80 Rear view of SMART-50 printer 2 Please connect network cable (RJ45)to a printer. (Network cable is not supplied. Please asknetwork administrator for more questions.) ① ② ③ ④
38 2.5.2 Network configuration DHCP (Dynamic Host Configuration Protocol) which automatically assigns IP address to the SMART-50 network printer on the same network is default for IP configuration. If you don’t have DHCP server, you need to set static IP. Please run NetAdmin.exe in the SMART-50 installation CD to set or change network configuration. Pic.81 Running the NetAdmin NetAdmin is run as the Pic74 after turning on SMART-50 network printer. ① Printer Connection Status Searches local network, finds and shows available network printer. ② Network Module Management Searches connected encoder on networkmodule. Reboots, Resets network module. Firmware upgrade available ③ Printer Configuration Sets detailed system configuration. ④ Network Information Shows firmware version of network module Pic.82 Network printer is not found When no printer is connected to network, there is no printer shown on the box. Please click “Refresh”. If no printer shown, please check as below, 1. Please check the printer is turned on. 2. Please check network cable is connected to network hub and works properly (LED lamp blinking). 3. Please check if there is DHCP server in the local network. When DHCP server is not in your local network, you need to set Static IP. 4. If Static IP is used, please check the IP configuration. If another device uses same IP address, it doesn't work. ③ ④ ② ①
39 Pic.83 Connecting to USB port If you are unable to find printer in local network, please connect printer by USB. You can setup network by USB. When you click Refresh, you can find a printer connected by USB as shown in the Pic.80. z You don’t need to install device driver for network configuration by USB. Please ignore messages related to device installation. z You can change values of “System Management” only when you connect a printer by USB. Please connect a printer by network to use all of the functions of Netadmin.exe. Pic.84 NetAdmin Log-in Please select a proper printer and click “connect”. Please enter password and click “OK”. Default password is “admin”.
40 Pic.85 Dynamic IP configuration If you setup network automatically, please choose DHCP. z Please select DHCP and click “Set Configuration”. z “DHCP” is default for SMART-50 printer. z DHCP server should be in local network to use DHCP function. z Static IP is recommended. DHCP server assigns IP address automatically but this IP address is temporary, so the IP address may be changed. In this case, the network error may occur in connecting to SMART-50 network printer. Pic.86 Static IP configuration Please select “Static” for Static IP configuration. z Please enter values for “IP”, “Network Mask”, and “Gateway”. Click “Set Configuration”. z Please check IP address properly which does not conflict with other devices. z If you are not aware of static IP, please ask network administrator for Static IP. z We recommend using Static IP because it is more stable for using SMART-50 network printer.
41 Pic.87 Network service configuration You can change Service Configuration. z SMART-50 network printer provides 3 kinds of service (change “USB Spool”, “Network Spool” and “Network SDK”). You can select and change the service according to the need. z In “Network SDK”, you can control the printer and print a card well, and the printer supports SSL (Secure Sockets Layer) and User Authentication for security. z Please use default and ask technician for details. Pic.88 OCP configuration You can use Open Card Print function. z This function is for send commands and print through network card regardless of OSz Click check box “Use OCP” z “Use Terminal Emulation” is value for getting echo according to the commands through terminal. For security, it supports SSL and User Authentication. z Please do not change default value except special case..
42 Pic.89 Network user configuration You can add, change, delete User and change its password. z “admin” is administrator and you can’t deletethis account. Please don’t forget password for “admin” z “Get User”: shows available users z “Add User”: makes new user z “Del User”: deletes selected user z “Change Password”: changes password 2.5.3 Network module management Pic.90 USB port state “USB port state” shows USB device status connected on network module. z Network module has 4 USB ports. z Network module supports PC/SC. When you install the encoders that support PC/SC on network module, you can recognize the status of encoders.
43 Pic.91 Rebooting the network module “Reboot module” reboots network module. z Please click “Yes” when pop-up window comes out for reboot. z It takes 1 minute to reboot. z Please click “Refresh” after reboot. When proper printer shown, please connect printer by clicking “Connect”. Pic.92 Reset to default “Reset to default” resets to default and reboot network module. z Please click “Yes” when pop-up window comes out for reset. z It takes 1 minute to reboot. z Please click “Refresh” after reboot. When proper printer shown, please connect printer by clicking “Connect”.
44 Pic.93 Upgrading the firmware 1 “Upgrade firmware” enables to upgrade firmware of network module. z You can choose a firmware file. Pic.94 Upgrading the firmware 2 z Warning box will be shown during firmware upgrade for network module. z It is recommended not to do other work during firmware upgrade for system reliability. z Please do not turn off a printer until the upgrade is completed.
45 Pic.95 Upgrading the firmware 3 z When firmware upgrade is completed, pop-up comes out for reboot. Please click “Yes”. z It takes 1 minute to reboot. z Please click “Refresh” after reboot. When proper printer shown, please connect printer by clicking “Connect”.
46 3. Driver configuration 3.1. Checking printer properties To check printer properties, you need to open printer driver. Please open “Drivers and Printers” and right-click “IDP SMART-50 Card Printer”. Click “Properties”. For Windows 7 or 8, please click “Printer Properties”. Pic.96 Printer properties 1When you click “Printer Properties” as likePic.88, a device driver of “IDP SMART-50Card Printer” is shown. 3.2. Changing printer properties In the general tab shown as Pic.94, you can check the printer model and specifications. Pic.97 Printer properties 23.2.1. Printing Preferences Please click “Printing Preferences” shown on the bottom of Pic.95. There are 3 tabs of “Layout”, “Paper/Ribbon /Quality” and “Side/Media”. (You can set the options for printing shown on Pic.95.)
47 Pic.98 Layout 3.2.1.1. Layout - You can select either horizontal or vertical printing direction. To apply your selection, click “OK”.
48 Pic.99 Advanced Setup 3.2.1.2. Advanced setup Reset Default Values: Reset to default. Color Correction: You can correct gamma for colors. You need to use CardPrinterSetup to adjust color densities. Resin Black (K) Processing: Set criteria for resin black processing. Text: to set density criteria for extracting black objects Dot: to set density criteria for extracting black dots Threshold: to set density criteria on dithering Dithering Degree: to set sharpness on dithering Extra Controls : Edge Size: to set not printed area in case of not using Edge-To-Edge Eject Card: to set if eject a card after printing Erase Density : to set erase density forSMART-30 R Erase Sharpening: to calibrate image sharpened Flip Front: to set printed direction of image on front side. Flip Back: to set printed direction of image on back side. Magnetic Strip Encoding Method: to set magnetic stripe encoding method for each track Normal: to encode on LoCo Card forwards Reverse: to encode on LoCo Card backwards Bit: to encode on LoCo Card in Bit HiCo Normal: to encode on HiCo Card forwards HiCo Reverse: to encode on HiCo Card backwards HiCo Bit: to encode on HiCo Card in Bit Magnetic Card Flip R/W: to set back side image printing when magnetic encoding Magnetic Simple Encoding: Set fast encoding and printing Magnetic Auto Encoding: Set auto coercivity. Magnetic Encoding Ballys mode: Set Ballys mode Manual Magnetic Stripe encoding: to put in data on magnetic stripe manually Not Use: not to use magnetic stripe encoding Encoding and Printing: to print after magnetic stripe encoding Encoding or Laminating only: encoding magnetic or laminating. without printing
49 Pic.100 Paper / Ribbon / Printing 3.2.1.3. Paper / Ribbon / Printing z Supply Tray  Supply Please select “CR-80” because SMART-50 has 1 input hopper.  Tray Please select “Auto” because SMART-50 supports CR80 cards only. z Ribbon  Ribbon It shows the type of installed ribbon. You don’t need to select this option as SMART-50 recognizes ribbon automatically with RF Tag.  Resin You can set the method to extract resin black when you use design programs. (If you use Smart Design, you don’t need to select this option.) It will be set automatically. Black Objects: to extract resin black automatically for text, line, box, circle, binary images, etc. Black Texts: to extract resin black for text only Black Dots: to extract resin black for all of black Not Use: not to extract resin black  Split You can set the both sides (Front:YMCO, Back:K) to save color ribbon(YMCKO, HYMCKO, BYMCKO). It is only activated while printing both sides option is set. z Printing  Mode Set printing mode Standard: Default print mode. Prints all area of priniting Partial: Partial print mode. It is printed partially for the print area only. Printing speed can be faster than standard mode.  Speed Set printing speed and quality. Standard: Default print mode and best quality setting option of printing High: Fast print mode. This option can be used with only K and KO ribbo. Printing quality might be lower than Standard.  Color You can select color or black&white print. (“Color” option is available only with color ribbon.)  Dither There are 3 possible selections, Threshold, Random, and Diffusion Dither. It is performed with K and KO ribbon only. (Please select “Diffusion Dither” for high quality.)
Pic.10Pic.101 Side / M02 Laminaedia ator 50 3.2.1To se - PrinYou c(It is p - FronYou c(whitefront You BITMBlue Pink (Black 3.2.1This tis conPrinteTo se - LamYou cboth s - OveYou cDefaurecom - PosYou cvalue1/300 - TemYou ccan b - LamYou settinPrinteEnco“Enco.4. Side / Met printing sidnt Side can select onpossible onlynt / Back can use a pree card, smaror back sidecan define AP file (1012(RGB(0,0,25(RGB(255,0,k (RGB(0,0,0.5. Laminatap will be crnnected to Per, this tap wet Laminator minator Sidecan select nsides printingerlay can select whult setting is mmend to ussition can set Lamies can be s0 inch. mperature can set Lambe set from 1minating Onlcan skip prng a value iner setup - Prding and oding and LaMedia e and printinne side printiy when you hedefined martcard, Magn. a mask. Us2 X 636 pixe55)): Print an,255)): Print o)): Print, Oveator reated only wPC. In the caill be not dispprinting optioe not use, topg hether overlano overlay we the defaultnating start pet from -50minating temp00℃ to 180ly rinting and rint preferencLaminating aminating Onng mask. ng or both shave a flippeask or user dnetic stripe cser defined els). nd Overlay only erlay and Flowhen SMARTase of normaplayed. ons. p side, bottoay prints or nwhen laminat value. position of w0 to 50. Theperature and0℃. do laminatices - Advan- Set thenly” ides printingr.) efined maskard, etc.) onmask usesorescent T-50L printerl SMART-50om side andnot. ating and wewidth and thee number isd the valuesing only bynced Setup -e value asg kn s r 0d e e s s y -s
51 3.3. Other settings Pic.103 Printer sharing 3.3.1. Sharing You can share a printer with Sharing tab via Network. Default is “Not sharing” Pic.104 Ports 3.3.2. Ports Port tab shows which port is connected with SMART-50. SMART-50 has connection with USB Virtual printer port as Pic.101 because SMART-50 uses USB connected to PC. (Caution! This port is selected automatically. It is recommended to maintain default.)
52 Pic.105 Advanced 3.3.3. Advanced It is available for Working Time setting, Priority order, Spool print etc. in “Advanced” tab. “Advanced” setting follows MS Windows standard. If you want to change the setting, please refer to the Window manual. (It is recommended to maintain default.) Pic.106 Color Management 3.3.4. Color Management In “Color management” tab, you can select color management profile fit to the printer. SMART-50 uses color profile to express optimal color. The driver selects color profile automatically to fit each ribbon. (It is recommended to maintain default.) Pic.107 Service 3.3.5. Service You can recognize printer serial, printer ID, driver version, firmware version, type of ribbon & balance and printer’s status. You can print the “technical support sheet” on a card to check printer’s setup value. To clean printer, please insert a cleaning card in a hopper and click “Clean Printer”. For further details, please refer “6.1. Cleaning Printer”. Please refer “4.2.6 Printer Status” for numbers of “Printer Status” and “Printer error”
53 Pic.108 Laminator 3.3.6. Laminator This tap will be shown only when SMART-50L printer is connected to PC. You can recognize laminator film’s type, balance, laminator’s version, serial number status.
54 4. Utilities 4.1. Card Printer Setup SMART-50 is produced with optimized setting. You need to adjust setting value if required or spare parts are replaced using CardPrinterSetup in our Installation CD. You can adjust following settings with CardPrinterSetup. 4.1.1. Run CardPrinterSetup Pic.109 CardPrinterSetup Log-in Password input window is displayed when you run this program. If you input the correct password, the recorded setup value will be shown and you can change values. The password is saved to SMART-50printer. If you use another PC with same printer, previous password is required to run this program. (Default password is none. Please press OK if you have not set password.) Pic.110 CardPrinterSetup start When you are successful to log-in, you can set values shown as Pic.107.
55 4.1.2. Card Printer 4.1.2.1. Basic Setup Pic.111 CardPrinterSetup – Card Printer Basic Setup ① To show connected printers Device: You can select a printer using pull-down menu. “IDP SMART-50 Card Printer” is a name of printer. “SMART228” is printer ID, “USB001” is connected port. ② To set administrator password and user password. Change Root PW: To set administrator (root) password. This password is used to verify user authority for CardPrinterSetup and User Authentication. Also it is required for User password management. (Please set password for security use.) Change User PW: To set user password for User Authentication. ③ Click “Card Printer” tap.(If laminator is installed, you can setup laminator setting value by “Laminator” tap. ④ To show firmware version, serial number of printer and serial number, resistor & type of print head. ⑤ To show print area. It shows exaggeratingly for user convenience. ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩
56 ⑥ To set print area. Please set it properly to print on an entire card because SMART-50 is a direct thermal card printer. When you click “⑦ Print”, a card is printed as like “④ example”. Please set values properly that all circles of each corner are printed and blank spaces are 0.4mm ~ 0.5mm in the top and the bottom of a card. Please set values by following order. X Start Position: Please set right and left properly by adjusting X position. Y Start Position: Please set the start position of printed example image and blank space in the top is 0.4mm ~ 0.5mm. Y End Position: Please set the end position of printed example image and blank space in the bottom is 0.4mm ~ 0.5mm. It is recommended to set bigger value for “Y scale” than default. Y Scale: Please set to show circles in the bottom. ⑦ To set density. SMART-50 enables to set different density for each color, resin black and overlay. So, please set each density for high quality. Please optimize the quality by adjusting each value. To optimize, you repeatedly adjust the density and print a Calibration card and check the print state until you get the optimum. If your printer is SMART-30 R model, please do not install ribbon. You can set density with Rewritable cards. Please adjust total density only. Total Density: To set all of the density (Color, Black and Overlay) at one time. If your printer is SMART-30 R model, when the density is too strong, you will have darker background color. (Background color may vary depending on card type.) When density is proper, texts and images are printed clearly and there is no background color. When density is too low, texts and images are printed dull. Pic.112 SMART-30 R density YMC Density: To set color density. Please maximize YMC density as you can, which enables to express range of color and vivid images. If it is too strong, green or red marks are appeared. If it is too weak, the print quality will be dull. (Please refer Pic.109.)
57 Pic.113 Color density Black Density: To set resin black density. In Pic.111, barcode is printed to express density. When density is too strong, barcode is printed too thick. When density is too weak, barcode is too thin. Please adjust resin black density to express clear barcode. Please refer following pictures. Pic.114 Resin Black density Overlay Density: To set overlay density. Please set it when overlay is printed on surface regularly. If it is too strong, it is hazy and marks are appeared. If it is too weak, overlay panel is not printed edge areas. You can check it with printed card under the light. Pic.115 Overlay density ⑧ To print calibration card. ⑨ To show advanced Setup. (It is recommended not to set advanced setup.) ⑩ To load or save values. Get Config.: to get values from current printer
58 Set Config. : to set values to current printer Load from File: to load values from file Save to File : to save values to file Load Default : to load default. Please adjust values again after load default. Close : to close CardPrinterSetup
59 4.1.2.2. Advanced Setup You can set more values. Pic.116 CardPrinterSetup – Card Printer Advanced Setup ① You can set Printer ID, PC serial, Print head and Magnetic encryption key. Change Printer ID: When SMART-50 is used by SDK, you can set unique ID for SMART-50 printer regardless of whether it is connected by USB or what IP address is. It is useful to connect and use several printers. Default is “SMART-50”. Set PC Serial: One of security function. You can use a printer with specific PC. It is activated when you click “Set PC Serial” after “PC Authentication” of ⑥ is ticked and rebooted. At that time, the specific information of used PC is saved to SMART-50 printer. Change Head: When you replace thermal print head, you must change head information for optimal quality. Please change head serial number, resistor and type of head in the Change Head Dialog window after click “Change Head”. Set Mag. Encrypt Key: One of security function. When you use SDK, you can encrypt magnetic stripe encoding data transmitted by USB. You can define and save the encryption key to SMART-50 using “Set Mag. Encrypt Key”. ② To show how many cards are issued with SMART-50 printer. “Total Issue Count” is the number of issued cards from factory shipment, “User Issue Count” is the number of issued cards from replacing head. When you replace a head, please initialize the number by ticking “Reset User Issue Count”. ③ To show color and motor management. SMART-50 recognizes ribbon color automatically and controls motor by ribbon remaining. “Yellow Level”, “Magenta Level”, “Cyan Level”, “Black Level” are default value for ribbon and user does not change values. “RMP+”, “RMP-“, “RMM+”, “RMM-“ are necessary variables to control ribbon motor. Please do not change values for them as it affects card quality. ④ SMART-50D is made by attaching a flipper in SMART-50, so you need to adjust it to be tuned in the horizontal. “Rotate Top” is a value when the card of top side is in line. “Rotate Bottom” is a value when card of bottom side is in line. Please click “Auto Rotator Set” when error is occurred during a card moved to or from a flipper. ① ② ③ ④ ⑤ ⑥
60 ⑤ Please refer as below for other values. Reserved: Not used Warming Up Display: If you use SMART-30 R, LED buttons are blinked during print head is warming up. You can adjust the timing of LED blinking by adjusting values of “Warming Up Display”. It becomes faster as the value is smaller. Mag. Write Mode: You can order the way how to encode magnetic stripe. “L:A, H:I”: encodes 3 tracks at once for LoCo card and encodes at twice by dividing 1,3 and 2 track for HiCo cards. Magnetic Space: The distance of magnetic stripe when you encode. SBS Only: Please enable it when you issue cards with software programed by SDK. This option disables printer device driver. Board Type: to choose they type of mainboard. Please do not change it. Security: There are several ways to set a security function for SMART-50. PC Authentication: You can use a printer with specific PC. It is activated when you click “Set PC Serial”. Physical Key: You can set this option when physical key is installed. User/Root Authentication: You can set passwords for User and Administrator. Use USB Serial: When SMART-50 is connected to USB, it transmits the USB serial number to PC. Default is the same number used by all SMART-50. Please set this option when you use multiple SMART-50 printers connected to 1 PC via USB. It enables unique serial numbers for each USB. Ribbon Position: To set the ribbon position on card. Please set it default. Warming Up Temp.: To control the temperature of warming up before printing. For SMART-30 R, you need to warm up print head to print high quality. We recommend warming up to 50 degrees. Card Out Delay: To set timing of hopper motor for ejecting card. Please set it default. Card Out: to set the way to eject cards. Error Card Out: to set the way to eject error cards. DCL Mode: When you use SDK and print cards with DCL mode, you don’t need to install printer device driver. Dump Mode: It records log data.
61 4.1.3. Laminator 4.1.3.1. Basic Setup Pic.117 CardPrinterSetup – Laminator Basic Setup ① The combo box shows connected printers ② Click Laminator Tap. ③ It shows the information of installed laminator such as firm-ware version, serial number. If you click “Change Serial No.” button, you can change serial number. ④ The fields show laminator film’s type, balance, code and laminator code. Film Type : It shows installed film’s type and vendor code. Film Remain : It shows installed film’s total number and balance. Laminator Code : It shows Laminator’s code, vendor and local code. Film Code : It shows installed film code, vendor and local code. ⑤ You can change the values according to the installed film type. ① ② ③ ④ ⑤ ⑥ ⑦
62 Heater Temperature : It is for laminating temperature. Laminating PPS : Laminating speed. Laminating Move Pulse : The distance of laminating movement. Separation with Card : After laminating and removing film, the value changes the distance of card movement Separation with Film : After laminating and removing film, the value changes the Distance of film movement. Lami. Start Card Pos : The value is for laminating start position. Torque Laminating Max : Maximum torque of motor while laminating. Torque Laminating Min : Minimum torque of motor while laminating. Laminating with Pulse : The value is for change laminating width. Film Attribution : It changes film attribution. ⑥ It shows “Advanced Setup” window. ⑦ “Save” or “Load” the values. Get Config : Read the values from connected printer. Set Config. : Set the values to connected printer. Load from File : Load the values from saved file. Save to File : Save the values into a file. Close : Close the program. 4.1.3.2. Advanced Setup Pic.118 CardPrinterSetup – Laminator Advanced Setup ① It shows total laminating count. ① ② ③
63 ② The values are for setting motor torque of film movement. Torque Move Max : Change Maximum motor torque Torque Move Min : Change Minimum motor torque ③ The values are for setting motor torque of laminating. You can set the values of each section. ④ You can set “Head” temperature of laminating. You can set the values of each section. ⑤ Rotator position
64 4.2. Card Printer Test Basically Card Printer use standard printer device so you can be used same as general paper printer. In the case of magnetic stripe, contact, contactless encoder option, you will need to install appropriate driver and operate individually. Encoding operation will be controlled by “CARD PRINTER SDK”. You can test all feature of printer by Card printer Test. Card Printer Test program is developed by using “SMART Printer SDK” 4.2.1. CardPrinterTest When CardPrinterTest is run, all function can be tested individually. Pic.119 CardPrinterTest ① Select Printer: select printer to test. In the Pic.116, “IDP SMART-50 Card Printer” is the Printer name, SMART228 is the Printer ID, and USB001 is the connected port. ② Control : To execute each step to test ③ Print: Print test with CSD file which is designed by Smart Design program. ④ Batch Start: Repeat selected encoding test by “⑤ Encoding” ⑤ Encoding: Encode Magnetic Stripe, Contact Card, Contactless Card ⑥ Printer Status: Check printer status. ⑦ Message: Description of status by log. ① ② ③ ④ ⑤ ⑥ ⑦
65 4.2.2 Select printer and control When you execute CardPrinterTest, it will search connected printers by USB and Network automatically and SMART-50 printer connected to USB has higher priority. Other printers could be selected by pull-down menu. You can test all function with connected printer. . Control is consisted by SBS(Step by Step), Move, Rotate, Etc. section and you can control printer by each step. z SBS SBS is to operate SMART-50 printer in SBS(Step-By-Step) mode which you can control the printer using commands. In SBS mode, after printing data transmission, printing a card will be run only by clicking “DoPrint”. It is the main difference between NORMAL mode and SBS mode. When you click “Start”, SMART-50 is operated in SBS mode, and existing spooled data will be eliminated. To exit SBS mode, click “Stop”. z Card Card is to bring a card into printer and eject a card. “In” is to move a card from input hopper to printer and “Out” is to move a card from printer to output hopper. In case the flipper is installed, “Back” ejects a card to the back side. z Move Move is to move a card to specific position in the inside of printer. “Print” is to move a card to the printing position, and “Mag.” is to the magnetic encoding position, and “IC” is to the contact smartcard encoding position, and “RF” is to the contactless smartcard encoding position. “To Rotator” is to move a card from printer to flipper and “From Rotator” is to move a card from flipper to printer. “from In” is to move a card from the card in sensor to where you define position, and “from Out” is to move a card from the card out sensor to where you define position. z Rotate Rotator is to flip over a card in the printer installed flipper. “Auto” is to move a card from printer to flipper and flip over a card and move a card to the printing position automatically. “Batch” is to repeat “Auto” as many times as the number of set. “To Bottom” is to turn to the backside of card and “To Top” is to turn to the front side of card. z Etc “Cleaning Roller” is to clean the roller by cleaning card automatically. “Use Log” is to display log in message space. 4.2.3 Print Print can be done through the CSD file which is designed by Smart Design program. Following the steps in this section. 1. Click “…” button and select the CSD file. 2. Click “Open” button to prepare CSD file to print. 3. Click “Print” Button to move print data to spool. In the NORMAL mode, Click “Print” button to print a card, but in the SBS mode, “Print” button to transmit a printing data from PC to printer and wait for printing. Therefore, you must click “DoPrint” to print in SBS mode. This function is for detail control of printer. 4. Click “Close” button to close CSD file. 4.2.4. Batch Batch is to repeat encoding/decoding test continuously. In the Repeat, you input the number of repeat and click “Batch Start”, then the test is run as many times as the number of set. When you check “Include Card In/Out”, each time the printer bring a card from input hopper and perform an encoding
66 test and eject the card. But if not, encoding test will be done only by one card. At that time, if there is no card in the printer, the printer bring a card into the printer from input hopper and repeat the encoding test on the card, and if there is a card in the printer, the encoding test is performed on the card repeatedly. “Card Holding” is activated when “Include Card In/Out” is ticked. When “Card Holding” is ticked and the repeat number is set, the printer repeats the encoding test as many times as the number of set in the “Card Holding” without ejection. When it is completed, the printer ejects the card and brings a new card into the printer and starts testing. In the Setting, “Retry” is to retry the encoding test when the error occurred. “Prompt on Error” is to display Pop up Message when the error occurred. If not, Error number will be counted without message. The number of error is displayed at Error section. 4.2.5. Encoding Magnetic: Magnet Stripe Encoding “Read” is to read and display the data from magnetic stripe card. It is composed of “Do Read” and “Read All Buffer” and runs “Do Read” and “Read All Buffer” sequentially. “Do Read” is to read the data from magnetic stripe card and store the data in the buffer. “Read All Buffer” is to transmit the date stored in the buffer to PC. If the track number is ticked, the data of the ticked track is only transmitted to PC. “Write” is to write the data to the magnetic stripe. It is composed of “Write All Buffer” and “Do Write” and runs “Write All Buffer” and “Do Write” sequentially. “Write All Buffer” is to transmit the data to the buffer. “Do Write” is to write the data stored in the buffer to the magnetic stripe of card. You can choose the magnetic foil type (LoCo or HiCo) and the track of magnetic stripe. “Random Fill” is to create a random magnetic encoding data for testing. Batch process repeats the following steps sequentially, Card “IN” Æ Move “Mag” Æ Magnetic “Random Fill” Æ Magnetic “Write” Æ Magnetic “Read” Æ Card “OUT”. Pic.120 Magnetic stripe encoding IC(PC/SC) : Contact Smartcard Encoding In SMART-30 printer, a contact smartcard encoder can be installed and SMART-50 printer supports the contact smartcard encoder in the printer inside and the SIM encoder on the right of front side. “IC(PC/SC)” is to test a contact smartcard and SIM encoding. “Batch” is applied only to the contact smartcard encoding because SIM encoder is installed outside and can’t move a card automatically. “ICH Contact” is to bring the encoder head into contact with the IC chip of smartcard physically.
67 “ICH Discontact” is to separate the encoder head from the IC chip of smartcard physically. “Init” is to recognize and display the installed contact smartcard reader. The recognized encoder will be displayed at the pull down control. “Contact” is to contact with the smartcard electrically and initialize. “Reset” is to finish the function electrically. After “Contact”, you can run “Get ATR”, “Read”, “Write” and “Clear”. “Get ATR” is to read the ATR data. “Read” and “Write” are to read and write the defined data (Name, Address and Phone). These could not be applied to all cards. “Clear” is to clear the displayed data (ATR, Name, Address and Phone). In case the data is read and written using APDU, Read/Write can be done by APDU commands. “Load APDU” is to read the stored APDU commands. “Save APDU” is to save the displayed APDU commands. “Clear APDU” is to clear the APDU section. “Send APDU” is to run the APDU commands. Batch process repeats the following steps sequentially, Card “IN” Æ Move “IC” Æ IC “ICH Contact” Æ IC “Init” Æ IC “Contact” Æ IC “Reset” Æ IC “ICH Dis-contact” Æ Card “OUT”. Pic.121 Contact smartcard encoding RF(PC/SC) : Contactless Smartcard Encoding In SMART-30 printer, a contactless smartcard encoder can be installed and SMART-50 printer has the internal and external contactless smartcard encoder. RF(PC/SC) is to read and write the contactless smartcard. Using internal encoder, the printer brings a card into the printer from input hopper and encodes a smartcard. Using external encoder, after putting a card on the top cover, you can encode because the antenna installed under the top cover is used. Therefore, “Batch” is applied only to the internal contactless smartcard encoding. “Contact” is to contact with the contactless smartcard electrically and initialize. “Reset” is to finish the function electrically. After “Contact”, you can run “Read”, “Write” and “Clear”. “Get UID” is for getting Chip Serial Number(CSN) “Read” and “Write” are to read and write the defined data (Name, Address and Phone). These could not be applied to all cards.
68 “Clear” is to clear the displayed data (ATR, Name, Address and Phone). In case the data is read and written using APDU, Read/Write can be done by APDU commands. “Load APDU” is to read the stored APDU commands. “Save APDU” is to save the displayed APDU commands. “Clear APDU” is to clear the APDU section. “Send APDU” is to run the APDU commands. Batch process repeats the following steps sequentially, Card “IN” Æ Move “RF” Æ RF “Connect” Æ Get UIDÆ RF “Discontact” Æ Card “OUT” Pic.122 Contactless smartcard encoding 4.2.6. Printer status “Get Temperature” is to get and display the temperature of Thermal Print Head. When the “Realtime Check” is ticked, it displays the current temperature of Thermal Print Head in real time. “Get Status” is to get and display the printer status. Status Code #define SMSC_M_CARDIN 0x0000000000000001 // Card In #define SMSC_M_CARDOUT 0x0000000000000002 // Card Out #define SMSC_M_MOVE_PRINT 0x0000000000000004 // Move to print #define SMSC_M_MOVE_PRN2ROT 0x0000000000000008 // Move from printer to flipper #define SMSC_M_MOVE_ROT2PRN 0x0000000000000010 // Move from flipper to printer #define SMSC_M_MOVE_IC 0x0000000000000020 // Move to contact encode #define SMSC_M_MOVE_RF 0x0000000000000040 // Move to contactless encode #define SMSC_M_MOVE_MAG 0x0000000000000080 // Move to Magnetic encode #define SMSC_M_THUP 0x0000000000000100 // Thermal head up #define SMSC_M_THDOWN 0x0000000000000200 // Thermal head down #define SMSC_M_ICHUP 0x0000000000000400 // Contact head up #define SMSC_M_ICHDOWN 0x0000000000000800 // Contact head down #define SMSC_M_PRINT 0x0000000000001000 // Printing #define SMSC_M_MAGRW 0x0000000000002000 // Read/Write Magnetic data #define SMSC_M_SEEKRIBBON 0x0000000000004000 // Ribbon search #define SMSC_M_MOVERIBBON 0x0000000000008000 // Ribbon Move #define SMSC_M_ROTATORTOP 0x0000000000010000 // Rotate Card up
69 #define SMSC_M_ROTATORBOTTOM 0x0000000000020000 // Rotate Card down #define SMSC_S_HOPPERHASCARD 0x0000000000040000 // Card in hopper #define SMSC_S_THUP 0x0000000000080000 // Thermal head up #define SMSC_S_CARDIN 0x0000000000100000 // Detect Card in #define SMSC_S_CARDOUT 0x0000000000200000 // Detect Card out #define SMSC_S_ROTATORTOP 0x0000000000400000 // Card front side up in Flipper #define SMSC_S_EQUIPROTATOR 0x0000000000800000 // Flipper installed #define SMSC_M_RECVPRINTDATA 0x0000000001000000 // Importing print buffer #define SMSC_S_HASPRINTBUFFER 0x0000000002000000 // Reserving print buffer #define SMSC_M_SBSRUNNING 0x0000000004000000 // Executing SBS Commands #define SMSC_S_SBSMODE 0x0000000008000000 // SBS mode #define SMSC_S_CASEOPEN 0x0000000010000000 // Case open #define SMSC_M_INIT 0x0000000020000000 // Initializing #define SMSC_S_TESTMODE 0x0000000080000000 // Test mode From card printer firm-ware version 1.00.60 , some values are changed like bellows from black color texts to red color texts. #define SMSC_S_THUP 0x0000000000080000 // Thermal head up status #define SMSC_S_CLEANWARNING 0x0000000000080000 // Need cleaning of printer #define SMSC_S_ROTATORTOP 0x0000000000400000 // Front card up status in rotator #define SMSC_S_EQUIPLAMINATOR 0x0000000000400000 // Laminator is installed Error Code #define SMSC_F_CARDIN 0x0000000100000000 // Error Card in #define SMSC_F_MOVETOPRINT 0x0000000200000000 // Card move Error #define SMSC_F_CARDOUT 0x0000000400000000 // Card out Error #define SMSC_F_MOVETOMAG 0x0000000800000000 // Card move Error (Magnetic) #define SMSC_F_MOVETOIC 0x0000001000000000 // Card move Error (Contact) #define SMSC_F_MOVETORF 0x0000002000000000 // Card move Error (Contactless) #define SMSC_F_MOVETOROTATOR 0x0000004000000000 // Card move Error (Printer to Flipper) #define SMSC_F_MOVEFROMROTATOR 0x0000008000000000 // Card move Error (Flipper to Printer) #define SMSC_F_THUP 0x0000010000000000 // Thermal head up Error #define SMSC_F_THDOWN 0x0000020000000000 // Thermal head down Error #define SMSC_F_ICHUP 0x0000040000000000 // Contact head up Error #define SMSC_F_ICHDOWN 0x0000080000000000 // Contact head down Error #define SMSC_F_ROTATORTOP 0x0000100000000000 // Card rotate up Error #define SMSC_F_ROTATORBOTTOM 0x0000200000000000 // Card rotate down Error #define SMSC_F_PRINT 0x0000400000000000 // Printing Error #define SMSC_F_MAGRW 0x0000800000000000 // Magnetic data Read/Write Error #define SMSC_E_SEEKRIBBON 0x0001000000000000 // Ribbon search Error #define SMSC_E_MOVERIBBON 0x0002000000000000 // Ribbon move Error #define SMSC_E_NOTH 0x0004000000000000 // Uninstalled Thermal head #define SMSC_E_THOVERHEAT 0x0008000000000000 // Overheat Thermal head #define SMSC_E_EMPTYRIBBON 0x0010000000000000 // No Ribbon #define SMSC_F_DATA 0x0020000000000000 // Data Error #define SMSC_F_CARDBACKOUT 0x0040000000000000 // Card out to back Error #define SMSC_F_CARDERASE 0x0080000000000000 // Cannot Remove data #define SMSC_F_INCORRECT_PW 0x0100000000000000 // Incorrect Password #define SMSC_F_MAGREADT1 0x0200000000000000 // Read data Error Mag. Track.1 #define SMSC_F_MAGREADT2 0x0400000000000000 // Read data Error Mag. Track.2 #define SMSC_F_MAGREADT3 0x0800000000000000 // Read data Error Mag. Track.3 #define SMSC_F_LOCKED 0x1000000000000000 // Device Locked #define SMSC_F_SPOOLFULL 0x2000000000000000 // Exceed Printer Spool #define SMSC_F_SET 0x4000000000000000 // Recent motion fail Laminator’s Status Code #define LMSC_M_HEATHDRLIFTUP 0x0000000000000001 // Heat-header is being lifted up #define LMSC_M_HEATHDRLIFTDOWN 0x0000000000000004 // Heat-header is being lifted down #define LMSC_M_CARDIN 0x0000000000000010 // Card In #define LMSC_M_MOVE_LAMINATE 0x0000000000000040 // Moving to laminate position #define LMSC_M_FRONTCARDOUT 0x0000000000000100 // Card is being moved out to front. #define LMSC_M_REARCARDOUT 0x0000000000000200 // Card is being moved out to rear. #define LMSC_M_ROTATE 0x0000000000000400 // Rotating #define LMSC_S_WAIT 0x0000000000000800 // Waiting #define LMSC_S_CMDRUN 0x0000000000002000 // Command is being executed. #define LMSC_M_HEATING 0x0000000000004000 // Heating Heat-header #define LMSC_S_CASEOPEN 0x0000000000008000 // Top cover is opened #define LMSC_M_LAMINATING 0x0000000000010000 // Laminating #define LMSC_S_CARDINSENSOR 0x0000000020000000 // Caught by card in sensor
70 #define LMSC_S_CARDOUTSENSOR 0x0000000040000000 // Caught by card out sensor #define LMSC_S_OUTDOORSENSOR 0x0000000080000000 // Caught by stacker open sensor Laminator’s Error Code #define LMSC_E_HEATHDRLIFTUP 0x0000000100000000 // Error while lifting up Heat-header #define LMSC_E_HEATHDRLIFTDOWN 0x0000000400000000 // Error while lifting down Heat-header #define LMSC_E_CARDIN 0x0000001000000000 // Error while moving card in #define LMSC_E_MOVE_LAMINATE 0x0000004000000000 // Error while moving to Laminate position. #define LMSC_E_FRONTCARDOUT 0x0000010000000000 // Error while front card out (printer side) #define LMSC_E_REARCARDOUT 0x0000020000000000 // Error while rear card out (stacker side) #define LMSC_E_ROTATE 0x0000040000000000 // Error while rotating #define LMSC_E_INIT 0x0000800000000000 // Error while initializing laminator #define LMSC_E_EMPTYFILM 0x0001000000000000 // Film remain count is 0. #define LMSC_E_NOFILM 0x8000000000000000 // No film is installed, or cannot 4.3. Firmware upgrade When you run the CardPrinterFirmware, you can see the pop-up window as the Pic. 120. Device: Select the local printer that you want to upgrade. Card Printer / Laminator: Select the device you want upgrade. Device Version: Displays the current firmware version of selected printer. Binary File: Click “Browse” button and select new firmware file to update. Manual Update: It is used when you want to upgrade manually. Update: Upgrades automatically. In generally, we recommend upgrading automatically. Close: Exit. Message : It displays information of upgrading. Pic.123 Upgrading printer firmware
71 4.3.1. Card Printer Firm-ware Upgrade. If you click “Browse” and select the new firmware, “Manual Update” and ”Update” are activated. At that time, click “Update” button to upgrade automatically, then the printer is upgraded after rebooting. (Caution: Please do not close upgrade dialog box until it is completed successfully and do not turn off the printer.) Pic.124 Ready for firm-ware upgrade In case there are some problems in the automatic upgrade, you click “Manual Update” and can see the pop-up widow as below picture. It shows procedure of manual upgrade. You can upgrade manually according to this procedure. Pic.125 Firm-ware manual upgrade
72 4.3.2. Laminator Firm-ware Upgrade. This function is only for card printer firm-ware version 1.00.60 and laminator should be installed to the printer. If you click “Browse” and select the new firmware, “Manual Update” and ”Update” are activated. At that time, click “Update” button to upgrade automatically, then the printer is upgraded after rebooting. (Caution: Please do not close upgrade dialog box until it is completed successfully and do not turn off the printer.) Pic.126 Ready for laminator firm-ware upgrade In case there are some problems in the automatic upgrade, you click “Manual Update” and can see the pop-up widow as below picture. It shows procedure of manual upgrade. You can upgrade manually according to this procedure. Pic.127 Firm-ware manual upgrade
73 5. Optional device driver installation In SMART-50 printer, you can install the optional devices that encode contact smartcard or contactless smartcard. If your purchased SMART-50 printer has optional devices, you should also install the smart card reader drivers. 5.1. Contact smartcard reader In SMART-50 printer, you can install the two types of optional devices which are contact smartcard reader and mobile SIM smartcard reader. If you have one or more smartcard reader devices on your printer, you should install the smartcard device driver as in the following, and connect SMART-50 printer to your PC. 5.1.1. Run the smartcard driver installer Insert the smartcard installation CD and find “\Options\Gemalto PC Twin” directory on your CD. Find the right directory which is installed OS version on your PC, and run the installer. You can see the smartcard reader driver installation window as the Pic.125. And click “Next”. Pic.128 Contact smartcard reader driver installation
74 5.1.2. License agreement The license agreement window as the Pic.126 is shown. Check at the agreement and click “Next”. Pic.129 License agreement 5.1.3. Installation The installation message is shown as the Pic.127. Click “Install” to install driver. Pic.130 Installing the contact smartcard reader driver
75 5.1.4. Complete installation When the installation is completed, the window as the Pic.128 is shown. Click the “Finish” to complete the installation steps. Pic.131 Completing the smartcard reader driver installation
76 5.2. Contactless smartcard reader In SMART-50 printer, you can install the two types of smartcard reader which are internal contactless smartcard reader and external contactless smartcard reader. If you have one or more contactless smartcard reader devices on your printer, you should install the contactless smartcard device driver as in the following, and connect SMART-50 printer to your PC. 5.2.1. Connect SMART-50 printer to PC When you connect the printer to PC and turn on the printer, you can see the “Found New Hardware Wizard” as the Pic.129, then Check “No, not that time” and Click “Next” to continue. Pic.132 Found New Hardware Wizard 5.2.2. Choose the installation method At the window as the Pic.130, select “Install from a list or specific location” and click “Next”. Pic.133 Installation method selection
77 5.2.3. Driver location Insert the smartcard installation CD and find “\Options\ Omnikey 5121” directory on your CD. Find the right directory which is installed OS version on your PC, and select the directory as the Pic.131, and click “Next”. Pic.134 Driver location 5.2.4. Complete installation When the installation is completed, the window as the Pic121 is shown, click “Finish” to complete the installation steps. Pic.135 Completing the driver installation
78 6. Troubleshooting 6.1. Cleaning the printer To maintain the best condition of SMART-50 printer, you must clean the printer periodically. If you use the exclusive cleaning card as the Pic.133, you can clean the printer easily. For purchase the exclusive cleaning card, ask to SMART-50 printer provider. Pic.136 Exclusive cleaning card for SMART-50 printer If the exclusive cleaning card is ready, click the “Clean Printer” in the service tab of SMART-50 printer driver as the Pic.134. After click, Clean Printer program to clean the printer is run. Pic.137 Printer cleaning start Step 1. Connect the SMART-50 printer to PC and turn it on, and prepare the exclusive cleaning card.
79 Pic.138 Printer cleaning Step 1 Step 2. Open the hopper and top cover and remove the card and ribbon cartridge. Pic.139 Printer cleaning Step 2 Step 3. Insert the exclusive cleaning card into the printer through input hopper as the Pic.137. When
80 the exclusive cleaning card is inserted to the cleaning roller, it will be move automatically. It is normal that the exclusive cleaning card is inserted to the ends and rollers are moving to clean. Pic.140 Printer cleaning Step 3 Step 4. Close the top cover to clean the Thermal Print Head and the printing roller. When the top cover is closed, cleaning card will be moving back and forth to clean. Pic.141 Printer cleaning Step 4 Step 5. Wait until the cleaning is completed. When the cleaning is completed, the exclusive cleaning
81 card will be ejected automatically as the Pic.139. Pic.142 Printer cleaning Step 5 Step 6. Remove the exclusive cleaning card and install ribbon cartridge into the printer. Pic.143 Printer cleaning Step 6
82 6.2 TPH (Thermal Print Head) replacement 1. Check the serial number and the resistance of new Thermal Print Head as the Pic. 141 TPH type: A = KEE, B = KPE Serial No.: see the red box. TPH resistance: see the green box. Pic.144 Thermal Print Head 2. Set up the new TPH’s configuration using CardPrinterSetup program. Step1: Run ‘Card Printer Setup’ in Utilities of the installation CD and click expansion button. Step2: Click “Change Header” in the extended setup. Step3: Input the TPH’s Serial No., Resistance and Type (choose KEE or KPE) on the TPH’s label, and click “OK”. Step4: Click “Set Config” to set the new TPH’s configuration. Pic.145 Print head setup 3. Replacing the new TPH Step1: Remove the old TPH from the top cover. (1) Turn off the printer and open the top cover. (2) Hold the TPH and press the locked hook, then the TPH is disconnected as the Pic. 143. (3) Disconnect the TPH from print head wire carefully. (Caution: TPH is possible to HOT.) Step2: Installing the new TPH (1) Connect new TPH to the print head wire. (2). Put the new TPH on the Shift and pull it up until be locked as the Pic. 143.
83 Pic.146 Print head replacement 4. Setup the print position and the color density. After installing the new TPH, you must reset the print position and the color density using CardPrinterSetup utility. Refer to “4.1.2 Default setting” 5. Calibration of Print Head Angle To get the best print quality, the TPHshould be located vertically with cardsurface. If print quality has the problem, it could becaused by print head angle. Through Adjusting print head angle byscrew (red mark in the Pic.144), you couldmake good quality of print. (Use the appropriate screw driver toadjust, and turn the screw by 90 degreesat a time.) Pic.147 Print head angle 6.3. Card movement 6.3.1. Cards can’t enter into the printer from input hopper. z Non-standard cards or bad cards. Change the cards. You can use only ISO CR-80 card (54mm x 86mm). z Card thickness control lever is set improperly. Regulate the card thickness control lever to fit the current card thickness. z Bad card array. Array the cards again and put them on input hopper as section 2.2 in this manual. z Cards have static and moisture. Remove the moisture or static. 6.3.2. Card Transfer Error occurs when the ribbon is coiled around the transfer roller or the printing roller. Open the top cover and remove the card and the coiled ribbon from SMART-50 printer using front LED buttons. If this problem occurred frequently, check the below things. z Non-standard cards or bad cards. Change the cards. You can use only ISO CR-80 card (54mm x 86mm). z The transfer roller or the printing roller is contaminated with the dust and dirt Remove the dust and dirt with the cleaning kit as section 6.1 z Wrong printing position setting. Please contact the local supplier z When operating temperature and humidity is out of the acceptable operating limit of the printer. Adjust the operating environment of the printer.
84 6.3.3. An Error occurs while the card is being transferred. First of all, check the Error message at LCD display. Open the top cover and remove the card by LED buttons. If this problem occurs frequently, check the followings. z Non-standard cards or bad cards. Change the cards. You can use only ISO CR-80 card (54mm x 86mm). z Printer setting is changed or is not proper. Please contact the local supplier. z The transfer roller or the printing roller is contaminated with the dust and dirt. Remove the dust and dirt with the cleaning kit as section 6.1. z The card surface is contaminated with the dust and dirt. Check the card surface and remove the dust and dirt and try again. If this problem occurs again, retry with new card. 6.4. Printing quality 6.4.1. Not printed or wrong colors printed spot. z The card surface is contaminated with the dust and dirt. After checking the card, change it to another card. z The cleaning roller is contaminated with the dust and dirt. Check the cleaning roller. If there is much dust, change the cleaning roller to the new one. z Much dust in the printer. Clean the inside of the printer with the cleaning kit. 6.4.2. Not printed horizontal line. z The ribbon cartridge is installed improperly. Check the ribbon cartridge installation state and whether the ribbon has wrinkles. z The printer head is contaminated with the dust and dirt. Clean the printer head with cleaning kit. z The printer head is damaged. Please contact the local supplier to replace the printer head. 6.4.3. Unclear or not uniform print. z Uneven or bad card surface. Change the card. z Too high or low setting of the color density. Please contact the local supplier. The color density default of your printer needs to be changed. z The printer head is contaminated with the dust and dirt. Clean the printer head with cleaning kit. Pic.148 Printing quality trouble 1 Pic.149 Printing quality trouble 2Pic.150 Printing quality trouble 3
85 6.4.4. Not aligned color print. z Non-standard cards or bad cards. Change the cards. You can use only ISO CR-80 card (54mm x 86mm). z Uneven or bad card surface. Change the card. z The transfer roller or printing roller is contaminated with the dust and dirt. Clean the rollers with the cleaning kit as section 6.1. z Worn-out printer. Please contact the local supplier. 6.4.5. Unplanned color print. z Non-standard cards or bad cards. Change the cards. You can use only ISO CR-80 card (54mm x 86mm). z Uneven or bad card surface. Change the card. z The transfer roller or printing roller is contaminated with the dust and dirt. Clean the rollers with the cleaning kit as section 6.1. z Worn-out printer. Please contact the local supplier. 6.5. Magnetic stripe encoding 6.5.1. Magnetic encoding error. First of all, Please press left LED button to retry. z The magnetic head is contaminated with the dust and dirt. Clean the magnetic head with the cleaning kit. z The magnetic encoding data is not transmitted or the wrong data is transmitted. Check the setting of the program and the driver and the magnetic encoding data you transmitted. z The card is not magnetic card, or inserting direction is wrong. Change the card or the direction. z Bad magnetic stripes on the card. Change the card. 6.6. General operation 6.6.1. Ribbon snapped during printing. Open the top cover and take out the cartridge. After putting the snapped pieces on together, install the cartridge again. Check the followings if this kind of problem occur frequently. z Non-standard cards or bad cards. Change the cards. You can use only ISO CR-80 card (54mm x 86mm). z Too high or low setting of the color density. Please contact the local supplier. The color density default of your printer needs to be changed. Pic.151 Printing quality trouble 4Pic.152 Printing quality trouble 5
86 6.6.2. LCD display “Ribbon Not Found” Press the left LED button to retry. If it occurs frequently, check the followings. z Not genuine ribbon. Change to the genuine ribbon. z Ribbon is consumed. Printing is not possible if ribbon is used up. Change the ribbon. z Snapped ribbon. Open the top cover and take out the cartridge. After putting the snapped pieces on together, install the cartridge again. 6.6.3. Printer doesn’t operate even if the printing data has been transmitted. Check the following. z Printer power off. Check the power. Turn on the printer power. Check the printer adaptor whether it is connected with a socket and the printer. z Bad power adaptor. Please contact the local supplier for replacement of the adaptor. z The printer driver is “Offline”. Change the printer driver to “Online”. z The printer’s USB cable is disconnected or the connection is bad. Check the cable’s connection between PC and the printer. If not good, make the USB cable connection again. z Bad USB cable. Change the USB cable. z The printing is operated with another printer driver. Select the correct SMART-50 printer driver again. z Wrong USB port setting of the printer driver. Check the port setting of the printer driver and change the port setting. z No ribbon in the printer or error occurred. Install ribbon in the printer or resolve the error. z Too long power or USB cable (more than 1.5M). Use the cable provided with the printer. z PC’s USB port is down: Reboot your PC.
87 7. Printer specification Product Specification SMART-30S SMART-30R Print Type Dye-Sublimation / Resin Thermal Transfers Direct Thermal Printing & ErasingPrint Area ResolutionDual Side Printing Option - Card Feeding Card Size Card Thickness Card Type PVC, Composit PVC, PET Rewritable Thermochromic MaterialMonochrome 6 sec. (600 cards/hour) 20 sec (180 cards/hour) for Erase & WriteYMCKO 28 sec. (128 cards/hour) -YMCKOK - -Input HopperOutput HopperMonochrome Ribbon 1200 cards/roll-Color Ribbon YMCKO 250 cards/roll- MemoryControl Panel 1 LED Buttons 1 LED ButtonsSupported PlatformCommunicationsPower SupplyPower ConsumptionTemperature/HumiditySize(W x L x H) 172mm x 377mm x 190mm 172mm x 377mm x 190mmWeight 3.4Kg / 7.5lbs 3.1Kg / 6.8lbsMagnetic StripeContact Smart CardContactless Smart CardCertificationsPrintingCardsISO CR-80 (54mm x 86mm / 2.12" x 3.38")0.38mm (15mil) ~ 0.76mm (30mil)Edge to EdgeFree Voltage (AC 100/220V, 50~60Hz)ISO7811 (Track Ⅰ,Ⅱ,Ⅲ Read / Write), JISⅡ, HiCo / LoCo45W15~35℃ / 20~80%Certifications300 dpiAutomatic64MBPrint Speed(Max.)80 cardsCE, FCC, KCCapacitySystem25 cardsMicrosoft Windows 2003, XP, Vista(32/64bit), 7(32/64bit), 8(23/64bit)DimensionsISO7816 (ID-1), SIM Type - ISO7816 (ID-000)USB, Ethernet(Option)EncodingMiFare, DesFire, ISO 14443(type A/B), ISO 15693, iClass Pic.153 Printer Specification 1
88 Product Specification Print Type Print Area Resolution Dual Side Printing Card Feeding Card Size Card Thickness Card Type Monochrome YMCKO YMCKOK Input Hopper Output Hopper Monochrome Ribbon Color Ribbon Memory Control Panel Supported Platform Communications Power Supply Power Consumption Temperature/Humidity Size(W x L x H) Weight Magnetic Stripe Contact Smart Card Contactless Smart Card Certifications172mm x 472mm x 190mm4.2Kg / 9.2lbsDye-Sublimation / Resin Thermal TransfersSMART-30DYesPVC, Composit PVC, PET5 sec. (720 cards/hour)28 sec. (128 cards/hour)32 sec. (112 cards/hour)PrintingCE, FCC, KCCapacitySystem25 cardsMicrosoft Windows 2000/2003/XP/Vista/7/8, Mac OS, LinuxDimensionsISO7816 (ID-1), SIM Type - ISO7816 (ID-000)USB, Ethernet(Option)EncodingMiFare, DesFire, ISO 14443(type A/B), ISO 15693, iClass ISO7811 (Track Ⅰ,Ⅱ,Ⅲ Read / Write), JISⅡ, HiCo / LoCo48W15~35℃ / 20~80%Certifications300 dpiAutomatic64MBPrint Speed(Max.)100 cards1200 cards/rollCardsISO CR-80 (54mm x 86mm / 2.12" x 3.38")0.38mm (15mil) ~ 0.76mm (30mil)Edge to EdgeFree Voltage (AC 100/240V, 50~60Hz)YMCKO 250 cards/roll1 LED Buttons Pic.154 Printer Specification 2
89 Product Specification SMART-50S SMART-50D Print TypePrint Area ResolutionDual Side Printing Option Yes Card Feeding Card Size Card Thickness Card TypeMonochromeYMCKOYMCKOK - 27 sec. (130 cards/hour)Input HopperOutput HopperMonochrome RibbonColor Ribbon MemoryControl PanelSupported PlatformCommunicationsPower SupplyPower ConsumptionTemperature/HumiditySize(W x L x H) 170mm x 420mm x 195mm 170mm x 510mm x 195mmWeight 4.5Kg / 10lbs 5.5Kg / 10lbsMagnetic StripeContact Smart CardContactless Smart CardCertifications15~35℃ / 20~80%DimensionsEncodingPrintingCardsISO CR-80 (54mm x 86mm / 2.12" x 3.38")0.38mm (15mil) ~ 1.0mm (40mil)ISO7816 (ID-1), SIM Type - ISO7816 (ID-000)LCD Display / 2 LED ButtonsUSB, Ethernet(Option)Free Voltage (AC 100/220V, 50~60Hz)ISO7811 (Track Ⅰ,Ⅱ,Ⅲ Read / Write), JISⅡ, HiCo / LoCo45WMicrosoft Windows 2003, XP, Vista(32/64bit), 7(32/64bit)Dye-Sublimation / Resin Thermal TransfersPVC, Composit PVC, PET5 sec. (720 cards/hour)64MBPrint Speed(Max.)22 sec. (164 cards/hour)100 cardsEdge to EdgeMiFare, DesFire, ISO 14443(type A/B), ISO 15693, iClass 300 dpiAutomaticCertificationsCE, UL, FCC, KCCapacityYMCKO 250 cards/roll, YMCKOK 200 cards/rollSystem40 cards1200 cards/roll Pic.155 Printer Specification 3
90 Product Specification Print TypePrint Area ResolutionDual Side PrintingLaminating ModeLaminates Card Feeding Card Size Card Thickness Card Type YMCK & Single side Laminate YMCFK & Single side Laminate YMCKK & Single side Laminate YMCK & Single side Laminate YMCFK & Single side Laminate YMCKK & Single side Laminate Input Hopper Output Hopper Input Hopper Output Hopper MemoryDisplay & Control PanelSupported PlatformCommunicationsPower SupplyTemperature / HumiditySize(W x L x H)WeightMagnetic StripeContact Smart CardContactless Smart CardSMART-50LSimultaneous Mode (Front in/Back out)One-by-One Mode (Front in/Front out)100 cards40 cardsLCD Display / 2 LED ButtonsOne-by-One Mode (Front in/Front out)23 sec. (156 cards/hour)31 sec. (116 cards/hour)33 sec. (109 cards/hour)YesPVC, Composit PVC, PET-GSingle & Double with flip-over0.6mil, 1.0mil, Clear and HolographicSimultaneous Mode (Front in/Back out)Edge to Edge300 dpiAutomaticISO7811 (Track Ⅰ,Ⅱ,Ⅲ Read / Write), JISⅡ, HiCo / LoCo15~35℃ / 20~80%9.2Kg / 20lbs170mm x 900mm x 195mmEncoding54 sec. (67 cards/hour)Speed(Max.)100 cardsPrintingCardsISO CR-80 (54mm x 86mm / 2.12" x 3.38")0.76mm (29.9mil) ~ 1.0mm (40mil)Laminating44 sec. (82 cards/hour)52 sec. (69 cards/hour)Dye-SublimationMiFare, DesFire, ISO 14443(type A/B), ISO 15693, iClass CapacitySystem25 cardsMicrosoft Windows 2003, XP, Vista(32/64bit), 7(32/64bit)Dimensions64MBISO7816 (ID-1)USB, Ethernet(Option)Free Voltage (AC 100/240V, 50~60Hz) Pic.156 Printer Specification 4
FCC Information This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions : (1) This Device may not cause harmful interface, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures: 1.1. Reorient or relocate the receiving antenna. 1.2. Increase the separation between the equipment and receiver. 1.3. Connect the equipment into an outlet on a circuit different from that to which receiver is connected. 1.4. Consult the dealer or experienced radio/TV technician for help. WARNING Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. “CAUTION : Exposure to Radio Frequency Radiation. Antenna shall be mounted in such a manner to minimize the potential for human contact during normal operation. The antenna should not be contacted during operation to avoid the possibility of exceeding the FCC radio frequency exposure limit.

Navigation menu