Hyundai IBT L24C0F081-1 LCD monitor User Manual W240D ENGLISH

Hyundai IBT Corp. LCD monitor W240D ENGLISH

User manual

NEXTUser’s GuideType No. L22C0E081Model. W242DMulti Function Wide Monitor
U.S.A.U.S.FEDERAL COMMUNICATIONS COMMISSIONRADIO FREQUENCY INTERFERENCE STATEMENTINFORMATION TO THE USERNOTE : This equipment has been tested and found to comply with the limits for aClass B digital device pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmfulinterference in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and, ifnot installed and used in accordance with the instructions, may cause harmfulinterference to radio communications.However, there is no guarantee that interference will not occur in a particularinstallation.If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the followingmeasures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet of a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for assistance.Changes or modification not expressly approved by the party responsible forcompliance could void the user's authority to operate the equipment.Connecting of peripherals requires the use of grounded shielded signal cables.
1. Introduction2. Safety Information1/23This manual contains instructions for installing and operatingHYUNDAI IT CORP. HYUNDAI IT CORP. This is a highly ergonomic color display unit.• 24” viewable WUXGA LCD• High quality screen re-scaling capability• 100-240V AC input voltage• VESA DPMS (Display Power Management Signaling)• VESA DDC1/2B compatibility• Advanced digital On-Screen-Display controls• Digital Signal Input by DVI-1.0 Compatability• Fast and accurate auto adjustment • Most advanced image scaling• Supporting VESA Flat Panel Monitor Physical Mounting InterfaceThis Monitor has been engineered and manufactured to assure your safety. You can prevent serious electrical shock and other hazards by keeping in mind the following:Do not place anything wet on the monitor or the powercord. Never cover the ventilation openings with anymaterial and never touch them with metallic or inflammable materials.
2/23Avoid operating the monitor in extreme heat, humidity or areas affected by dust. Temperature : 5~40°CHumidity : 30~80RH Be sure to turn the monitor off before plugging thepower cord into the socket. Make sure that the powercord and the other cords are securely and rightlyconnected.Overloaded AC outlets and extension cords are dangerous, as are frayed power cords and broken plugs, which may cause electric shock or fire. Call your service technician for replacement.Do not use sharp tools such as a pin or a pencil near the monitor, as they may scratch the LCD surface.Do not use a solvent, such as benzene, to clean the monitor, as it will damage the LCD surface.
Cleaning and Maintenance• To avoid to risk of electric shock, do not disassemble the Cabinet of displayUnit. The Cabinet is not user-serviceable. Remember to unplug the display unitfrom the power outlet before cleaning.• Do not use alcohol (methyl, ethyl or isopropyl) or any strong dissolvent. Do notuse thinner or benzene, abrasive cleaners or compressed air.• Do not wipe the screen with a cloth or sponge that could scratch the surface.• To clean your antistatic screen, use water and a special microfiber screencleaning tissue used in optical lens cleaning, or lightly dampen a soft, cleancloth with water or a mild detergent.• If the instructions above do not help in removing stains, contact an authorizedservice agent. 3/23
4/23The following items should be found in the packaging.Above power cord can be changed upon different voltage areas. Pleasecontact your dealer if anything is missing or damaged.Other power cord except the cord packed in the product or longer than 3mmay affect EMC of the product in operating condition.3. Installing the monitor3-1. Packing List!UKAmerica/CanadaJapanAustraliaKoreaEuropeSouth AfricaPower CordSignal CableCompact DiscDVI Cable Audio Cable
5/233-2. Selecting a suitablelocation3-3. Connecting the PC• 15 pin D-sub / DVI-D /HDMI• Place the monitor at least 30cm from other electrical or heat-emittingequipment and allow at least 10cm on each side for ventilation.• Place the monitor in a position where no light shines directly onto or isreflected on the screen.• To reduce eye strain, avoid installing the display unit against a brightbackground such as a window.• Position the monitor so that the top of the screen is no higher than eye level.• Position the monitor directly in front of you at a comfortable reading distance(around 45 to 90cm) Before you start cabling your monitor, check that thepower is off on all units. To avoid any possibility ofelectric shock, always connect your equipment toproperly earthed outlets.1. Insert the other 15-pin/DVI-D/HDMI signal cable connector into the 15-pinVGA/DVI-D connection on your computer and screw it down. 2. Plug the power cord connection to connection on the monitor.3. Plug the other end of the power cord to your computer's main supply or to a100V-240V earthed electrical outlet.4. Turn on the monitor using the power switch and check that the power LED ison. If not, repeat steps 1,2,3 and 4 or refer to the Troubleshooting section ofthis guide.!!
7/23• Audio systemThis monitor has an audio system including two micro loudspeakers. Each of twomicro loudspeakers has an 3W(max.) output power. This system also supports aheadphone output jack.This system has been tuned to get a best tone quality which an audio inputlevel is under 500mv rms. If the input level is more than 500mv rms, you musttune down the audio input as the audio output tone may be distorted.7/23!!Speaker
8/233-4. Setting the refreshrate Follow the instructions below to set your refresh rate in Windows 98/ME/XP/2000.1. Go to the configuration window(Start-Settings-Configuration window).2. Double click on the ‘Display’ icon.3. Click on the ‘Settings’ tab.4. Click on the ‘Advanced’ button.5. Click on ‘Adapter’ and select 60Hz from the list.6. Click on ‘Apply’ to accept the selected value.
9/23Preset Timing TableIf the signal from the system doesn't equal to the preset timing mode, adjustthe mode with reference to the user guide of videocard because the screenmay not be displayed.!Resolution640 X 350720 X 400640 X 480640 X 480800 X 600800 X 600800 X 600832 X 6241024 X 7681024 X 7681024 X 7681152 X 8641152 X 8701280 X 9601280 X 10241280 X 10241680 X 10501600 X 12001920 X 1200480 i/p720 i/p1080 i/pH-Freq.(Khz)31.431.431.437.535.137.846.849.748.356.460.067.568.660.063.979.964.775.084.0V-Freq.(hz)70.070.059.975.056.260.375.074.560.070.075.075.075.060.060.075.060.060.059.950/6050/6050/60Supported ModeAnalog DVIVideo ModeNo.12345678910111213141516171819202122
W240DMulti Function Wide Monitor11/233-6. User’s Environment Recommended Ergonomic User’s Environment• Viewing angle of the monitor should be between -3~17 degree.
W240DMulti Function Wide Monitor12/23Kensington Security(Locking) SlotVESA MOUNT’G• This display unit supports a Kensington-type security device to secure yourmonitor. Kensington lock is not included.• To purchase and install the Kensington locking device, please refer to thefollowing contact information.* Kensington Technology Group· Address : 2000 Alameda de las Pulgas 2F san mateo, California 94403-1289· Tel : +1 650 572 2700 · Fax : +1 650 572 9675 · Web-site : www.kensington.com• This display unit supports VESA FPMPMI standard for 100mmx100mm screwmounting by giving 4 screw holes inside the base stand of the unit.• For buying VESA Flat Panel Monitor Mounting Devices, please contactfollowing information.* Ergotron, Inc.· Address : Ergotron Europe Kuiperbergweg 50 1101 AG Amsterdam The Netherlands· Tel : +3 1 20 696 60 65 · Fax : +3 1 20 609 04 59 · E-mail : info.eu@ergotron.comDesk MountWall Mount
4. Adjusting the picture13/23You can adjust the screen display by using the buttons located below thescreen.The second Menu from the OSD can't be chosen in digital-mode.
14/234-1. Using the On ScreenDisplay 4-2. Direct access buttonsTo make adjustments in the On Screen Display, follow these steps:1. Push the MENU button to call the OSD to the screen. 2. Push the or button to choose the item you want to adjust. The selected itemis highlighted.3. Push the SELECT button to adjust the highlighted item. 4. Use the or button to adjust the selection.5. Push the MENU button to return to the previous menu if you are in a submenu.6. The display unit automatically saves the new settings in 1 second after your lastadjustments and the menu disappears. You can also push the MENU button to makethe menu disappear.AUTO ADJUSTAt first display a full screen such as Window's back ground.Push the button SELECT(AUTO) to adjust the shape of screenautomatically.VOLUMEUse the button to select the Volume adjustment.Adjust with or button.SOURCEUse the button to switch the other input from current input.(VGA -> Component -> DVI -> HDMI -> VGA)
15/234-3. OSD Adjustments• PicturePCBRIGHTNESSTo adjust the brightness of the screen.CONTRASTTo adjust the contrast of the screen.H.POSITIONTo move image left and right.V.POSITIONTo move image up and downCLOCKTo adjust the horizontal size of the entire screen image.HDMI MODEBRIGHTNESSTo adjust the brightness of the screen.CONTRASTTo adjust the contrast of the screen.SATURATIONTo adjust color density.SHARPNESSTo adjust sharpness of screen.
• Color16/23PC ANALOGSTANDARDFor general Color tone.REDISHFor Redish color with warm tone.BLUISHFor Bluish color with cool tone.USERFor adjusting degree of RGB as User wantsAUTO COLORTO adjust the horizontal size of the entire screen image.HDMI MODESTANDARDFor general Color tone.DYNAMICTo be Sharper image.MILDTo be Smoother image.
17/23• Sound• SettingVOLUMETo adjust the audio volume level.BASETo emphasize low frequency audio.TREBLETo empahsize high frequency audio.BALANCETo use this function to balance sound from theleft and right speakers.MUTEAudio ON or OFFOSD CONFIGURATION- OSD TIMERTo adjust OSD Display time on the screen.- OSD POSTo adjust OSD Display position on the screen.- TRANSPARENTTo adjust the transparency of OSD window.- OSD ZOOMTo adjust the size of OSD window.INPUT SOURCETo switch between current source and other input source. ( VGA/DVI/COMP/HDMI )
DISPLAY CONTROLIf you choose DISP. CONTROL on the OSD menu, you can adjust the following<PC>- Full (16:10) : Shows full screen regardless of screen size.- 4:3 : Displays image at 4:3 ratio.<HDMI Mode>- Full (16:10) : Shows full screen regardless of screen size.- 16 : 9 : Displays image at 16:9 ratio. - 4:3 : Displays image at 4:3 ratio.- 1:1 : Displays image according to actual input pixels.- Zoom1 : Enlarges image by 20%- Zoom2 : Enlarges image by 25%.GENERAL RECALLRecall the saved initial dataLANGUAGEYou can select the language in whichadjustment menus are displayed. Thefollowing languages are available.English, German, French, Italian, Spanish,Dutch, Swedish, Finnish, Danish, Portuguese,Russian,Korean,Japanese,Chinese.18/23• Language
5. Display power managementReducing powerconsumptionIf the power management function of your computer is enabled, your monitorturns on and off automatically. You can control power management features fromyour computer.Your computer may have power management features which enable the computeror monitor to enter a power saving mode when the system is idle. You canreactivate the system by pressing any key or moving the mouse.The power button does not disconnect the monitor from the mains. The onlyway to isolate the monitor completely from the mains supply is to unplug themains cable.19/23Power consumption50W(Typ)1 W(Typ)0 WModeNormaloffUnpluggedLEDBlueRED(Orange)Not illuminated!
6. Troubleshooting20/23ProblemBlank screenError message:Video mode notsupportedThe display does not enter power managementmodePossible solutionIf the power LED is not lit, push the Soft power switch or check theAC cord to turn the monitor on. If the display unit is poweredthrough the computer, check that the computer is switched on.The display unit might be in standby mode. Push one of thekeyboard keys. Check that the keyboard is properly connected tothe computer.Check that the signal cable connector is properly connected and thatthe connection pins are not bent or damaged. If the connector isloose, tighten the connector's screws.Check that the power cable is correctly connected to the display unitand to the power outlet. Check the resolution and the frequency on the video port of yourcomputer.Compare these values with the data in the Preset Timing Table.The video signal from the computer does not comply with VESADPMS standard. Either the computer or the graphics adapter is notusing the VESA DPMS power management function.If your monitor is not functioning properly, you may be able to solve the problemby following the suggestions below :
21/23Possible solutionCheck that the signal cable connector is properly connected and thatthe connection pins are not bent or damaged. Try another colortemperature. Adjust the picture characteristics as described in the section OSDAdjustment(4-3).A problem with your graphics adapter or display unit. Contact yourservice representative.Check that the display resolution and frequency from your PC orgraphic adapter is an available mode for your monitor.In your PC, you can check through Control panel, Display, Settings.If the setting is not correct, use your computer utility program tochange the display settings.Check that the signal cabel connector is properly connected and thatthe connection pins are not bent or damaged.If the connector is loose, tighten the connector’s screws.Check that the computer is switched on.To enter a power saving mode. You can reactivate the system bypressing any key or moving the mouse.ProblemColor defectsSize, position,shape or qualityunsatisfactoryDuplicatedimagesImage is notstableMessage : No signalThe power LED isa orange color
22/23Possible solutionLED Indicator can be orange color on changing of video mode orInput Signal.Check the Resolution and the frequency on the video part of yourcomputer. Compare these values with the data in the Preset TimingTable.ProblemThe power LED isa orange colorContacting serviceIf the above troubleshooting hints do not help you find a solution to the problem,contact an authorized service agent. If the monitor is sent for service, use theoriginal package if possible.Unplug the display unit from the power outlet and contact a service agent when:• The monitor does not operate normally according to the operating instructions.• The monitor exhibits a distinct change in performance.• The monitor has been dropped or the cabinet has been damaged.• The monitor has been exposed to rain, or water or liquid has been spilled ontothe monitor.
7. Specifications23/23LCDDisplay areaNumber of colorInput signalsFrequency rateMaximum bandwidthMaximum resolutionRecommanded resolutionInput voltagePower consumptionPower managementPlug & PlayOSD menuAudio systemVESA FPMPMIErgonomics,Safety and EMCOperating TemperatureWeightDimensions (W X H X D mm)• Specification is subject to change without notice.• HYUNDAI IT CORP. specification on “dead pixel” of LCD Panel applies to ISO 13406-2 Standard.24" viewable, Diagonal, Pixel pitch 0.270mm, A-si TFT518.4(H) X 324(V), 24" Diagonal16.7 million colors ( true 8-bit color )R.G.B Analog(15pin D-sub) / DVI-D / Component / HDMIHorizontal : 30.0 to 80.0Khz, Vertical : 56 to 75hz162Mhz1920 X 1200 @ 60hz1920 X 1200 @ 60hz100-240V AC, 2.0A55W(Typ.)VESA DPMSVESA DDC 2BBRIGHTNESS, CONTRAST, H/W POSITION, CLOCK, PHASE, AUTOADJUST, AUTO COLOR, SOUND, OSD CONFIGRATION, INPUTSOURCE, DISPLAY CONTROL, GENERAL RECALL, LANGUAGE2ch X 2watts / Ear Phone Jack75mm X 75mm screw mountingEnergystarcTUVus, TUV-GS, CB, FCC, CE, VCCI, GOST5 ~ 40O C

Navigation menu