Hunter Fan TX16 Ceiling fan and lamp remote control. User Manual 41114 qf

Hunter Fan Company Ceiling fan and lamp remote control. 41114 qf

Users Manual

© 2001 Hunter Fan Company 1 41521-01 9-4-2001Hunter Fan CompanyRemote Ceiling Fan &Light ControlTransmitter Model: 84592Transmitter Battery: 12 V, Type 23A, MN-21 or equivalentReceiver Model: 85068Ratings: 120 VAC, 60 Hz, 1.0 Amp Fan300 Watts incandescent lightRead and Save these InstructionsCaution: Risk of Electrical Shock!All wiring must be performed in accordance with national andlocal electrical codes. If you are unfamiliar with the wiringcodes, you should use a qualified electrician.To avoid over heating and possible damage to other equipment,do not install to control a receptacle, fluorescent light fixture,motor operated appliance, or transformer-supplied appliance.Use only to control one paddle-blade ceiling fan andincandescent light fixture.Notes:1. This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1)this device may not cause harmful interference, and (2)this device must accept any interference received, includinginterference that may cause undesired operation.2. This equipment has been tested and found to comply withthe limits for a Class B digital device, pursuant to Part 15of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in aresidential installation. This equipment generates, usesand can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may causeharmful interference to radio communications. However,there is no guarantee that interference will not occur in aparticular installation.If this equipment does cause harmful interference to radioor television reception, which can be determined by turningthe equipment off and on, the user is encouraged to try tocorrect the interference by one or more of the followingmeasures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment andreceiver.• Connect the equipment into an outlet on a circuitdifferent from that to which the receiver is connected.• Consult the dealer or an experienced radio/TVtechnician for help.Note: Any changes or modifications to the transmitter orreceiver not expressly approved by Hunter Fan Companymay void one’s authority to operate this remote control.3. For use only with electrically reversible ceiling fans ratedat 1.0 amp or less, and fan incandescent light kits rated at300 watts or less.4. Not for use with shaded-pole or nonreversible motors. Notrecommended for use with the Hunter Original®.Before Installing the Control:1. Use the pull-chain switch to set the fan speed to the HIGHposition before installation.Note: Do not use the pull-chain to change the fan speedafter installation, as damage to your ceiling fan or controlmay result. The speed of the fan should only be changedby the control.2. Set the ceiling fan light kit to the ON position beforeinstallation. The light level should only be changed by thecontrol.Receiver Installation:1. Disconnect the power to the ceiling fan and light kit at themain electric panel. Remove fuse or move circuit breakerto the OFF position. Turn off wall switch.2. IMPORTANT! Before installing this control, change thefactory default jumper switch settings to your own uniquecode. Refer to Figure 1. Using small pliers or tweezers,pull out one or more of the three jumper switches byclamping on the small metal strip. Place the jumperswitches in the desire spots. Be sure the jumper switchpositions of the transmitter and receiver match, or theceiling fan will not function. Select different combinationsof jumper switches to prevent misoperation due to otherremote control fans, garage door openers, etc.Figure 1 - Jumper Switches3. Install the ceiling fan according to its instructions, up tothe point of making the electrical connections.Note: When installing this remote control on the fan, besure to cut and strip the fan leadwires to leave 6 1/2”outside of the hanger pipe.4. Use the two large wire nuts supplied to connect the receiverand house wiring, then use the three small wire nutssupplied to connect the receiver and ceiling fan wiring.Refer to the Wiring Diagram in Figure 2.Figure 2 - Wiring Diagram5. Install receiver as shown in Figure 3. Line up the slots onthe receiver with the ceiling plate. Be sure to push wireconnections from the ceiling back up through the hole inthe ceiling plate. Wires attaching from the ceiling plate tothe fan should be placed inside the canopy under theTransmitterBackJumperSwitchJumperSwitchReceiverBackLightKitFan CommonAntenna120 V ACPower InBlack MainWhite MainWhiteBlackBlack/White
41521-01 9-4-2001 2 © 2001 Hunter Fan Companyreceiver. Once the receiver is installed, continue with theappropriate instructions from the fan installation manualto finish installing the fan.Figure 3 - Installing ReceiverTransmitter Installation:1. Install a 12 volt alkaline battery inside the hand-heldtransmitter after setting the jumper switches to match thejumper switches in the receiver.2. Mount the remote holder over the ceiling fan’s wall switchusing the existing wall plate screws. Refer to Figure 4.3. The transmitter can be placed on the remote holder forconvenience or safekeeping.Figure 4 - Remote Holder AssemblyTesting the Control:Warning!• Do not use the pull chain to operate the light. Pulling thechain while power is applied can damage the receiver. Itis recommended to shorten the pull chain(s) to preventaccidental use.• Do not use the pull chain switch to change speeds. Pullingthe chain while power is applied can damage the receiveror ceiling fan.1. When the installation is complete, restore power at themain electrical panel. Then, turn on the wall switch. Thelight kit should turn ON. If the light remains OFF, turn offthe power at the wall switch. Pull the light kit’s pull chainto turn the light ON. Turn the wall switch back ON.2. Press the remote control’s fan speed button (refer to Figure4). The fan should start and reach it’s maximum speed. Ifthe fan does not start or is turning too slow, turn off thepower at the wall switch. Pull the fan’s pull chain to changespeed. Reapply power and try HIGH speed again. Repeatthis procedure until you have confirmed that the fan’s pullchain is set to HIGH speed.Operation:1. Turn ON the wall switch, the light will turn ON at maximumbrightness and the fan will be off.2. Standby Mode:• To save battery power, if no button on the remote ispressed for one minute, the remote LCD will go intostandby mode.• During standby mode, all LCD icons are turned OFF.• The LCD will resume original display when any buttonis pressed. The button function is not performed butacts as a wake up key.3. Light Operation:•ON and OFF: Press andquickly release the lightbutton on the hand-heldremote to turn the light OFFand ON.•Dimmer: Press and holdthe light button for morethan one second to dim or brighten the light. Ifbrightness is initially at 100%, then the brightness willdecrease to 95% and so forth by 5% increments aslong as the light button is pressed. When the minimumbrightness of 25% is reached, the setting will pauseand then begin to increase by 5% increments as longas the light button is pressed.•Auto Resume: The light button has an auto resume,so the brightness will stay the same as the last time itwas turned OFF.4. Fan Operation:•ON, OFF, and SpeedSetting: Press the fanbutton to turn ON the ceilingfan at HIGH speed. Pressagain to change the speedto MEDIUM, then again toLOW, and then again to turnthe fan OFF.5. Low Battery Detection:• The low-battery warningicon will flash when thebattery needs to bechanged. If there is a low-battery, it will also flashduring standby mode.• Replace the battery whenthe low-battery warning icon begins to flash.Ceiling PlateCanopyReceiverLightFanLCD Display
© 2001 Hunter Fan Company 3 41521-01 9-4-2001TroubleshootingSymptom Possible Causes Solution1. No functions operate.2. Operates only at close range.3. Inconsistent operation.Main Power not restored. Replace fuse. Turn ON circuit breaker. TurnON wall switch.Fan pull chain not set to HIGH. Turn OFF power at wall switch or mainelectric panel. Set fan to HIGH speed.Light pull chain not set to ON. Set light kit to ON.Receiver wiring incorrect. Verify wiring connections.Transmitter and receiver jumper switches donot match.Set transmitter and receiver to same jumperswitch setting.Battery too weak. Replace with new, alkaline battery.Signal blocked from reaching receiver. Extend antenna into ceiling box, or move itfor better reception.Battery too weak. Replace with new, alkaline battery.Signal partially blocked from reaching receiver. Extend antenna into ceiling box, or move itfor better reception.RF interference. Turn OFF wall switch for 5 seconds, thenturn back ON.Continuing RF interference. Change dip switch settings to a differentcode in both Transmitter and Receiver.
41521-01 9-4-2001 4 © 2001 Hunter Fan CompanyHunter Fan Company2500 Frisco AvenueMemphis, Tennessee 38125

Navigation menu