Huawei Technologies UAP2105 UMTS Access Point User Manual User Guide

Huawei Technologies Co.,Ltd UMTS Access Point User Guide

Installation Manual

UAP2105V300R011C90User GuideIssue 03Date 2009-08-20Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.
Huawei Technologies Co., Ltd. provides customers with comprehensive technical support and service. For anyassistance, please contact our local office or company headquarters. Huawei Technologies Co., Ltd.Address: Huawei Industrial BaseBantian, LonggangShenzhen 518129People's Republic of ChinaWebsite: http://www.huawei.comEmail: support@huawei.com Copyright © Huawei Technologies Co., Ltd. 2009. All rights reserved.No part of this document may be reproduced or transmitted in any form or by any means without prior writtenconsent of Huawei Technologies Co., Ltd. Trademarks and Permissions and other Huawei trademarks are the property of Huawei Technologies Co., Ltd.All other trademarks and trade names mentioned in this document are the property of their respective holders. NoticeThe information in this document is subject to change without notice. Every effort has been made in thepreparation of this document to ensure accuracy of the contents, but the statements, information, andrecommendations in this document do not constitute a warranty of any kind, express or implied.Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.
ContentsAbout This Document.....................................................................................................................11 Changes in the UAP2105 User Guide.....................................................................................1-12 Safety Precautions......................................................................................................................2-13 Introduction to the UAP2105....................................................................................................3-13.1 Appearance of the UAP2105...........................................................................................................................3-23.2 LED on the UAP2105.....................................................................................................................................3-23.3 Ports and Buttons on the UAP2105.................................................................................................................3-43.4 Specifications of the UAP2105.......................................................................................................................3-53.4.1 Performance Specifications of the UAP2105.........................................................................................3-53.4.2 Technical Specifications of the UAP2105.............................................................................................3-64 Installing the UAP2105..............................................................................................................4-14.1 Selecting a Position for Installing the UAP2105............................................................................................4-24.2 Installing the SIM or USIM Card....................................................................................................................4-24.3 Connecting UAP2105 Cables..........................................................................................................................4-35 Configuring the UAP2105.........................................................................................................5-15.1 Initial Configuration........................................................................................................................................5-25.1.1 PPPoE Mode..........................................................................................................................................5-25.1.2 FE Direct Connection Mode..................................................................................................................5-45.2 Defining a Subscriber in the AHR..................................................................................................................5-55.2.1 Adding a Zone........................................................................................................................................5-55.2.2 Adding a User.........................................................................................................................................5-75.3 Setting Parameters on the AP Manager...........................................................................................................5-95.3.1 Activating a Zone...................................................................................................................................5-95.3.2 Setting Parameters in a Zone................................................................................................................5-116 Routine Operation and Maintenance of the UAP2105........................................................6-16.1 Commissioning Services.................................................................................................................................6-26.2 Diagnosing Faults............................................................................................................................................6-46.3 Handling Alarms.............................................................................................................................................6-56.4 Upgrading the Software..................................................................................................................................6-56.5 Uploading AP Terminal Files.........................................................................................................................6-8UAP2105User Guide ContentsIssue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.i
7 Communication Ports Used by the UAP2105.......................................................................7-1ContentsUAP2105User Guideii Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
FiguresFigure 3-1 UAP2105............................................................................................................................................3-2Figure 3-2 LED on the UAP2105.........................................................................................................................3-3Figure 3-3 Ports and buttons on the UAP2105.....................................................................................................3-4Figure 4-1 Installing the SIM or USIM card........................................................................................................4-3Figure 4-2 Connecting the power adapter of the UAP2105.................................................................................4-4Figure 4-3 Cable connections (with the modem having only one LAN port)......................................................4-5Figure 4-4 Cable connections (with the modem having multiple LAN ports).....................................................4-5Figure 4-5 Cable connections (in FE direct connection mode)............................................................................4-6Figure 5-1 Configuring an AP..............................................................................................................................5-3Figure 5-2 Checking the configuration of the AP................................................................................................5-3Figure 5-3 FE direct connection mode.................................................................................................................5-4Figure 5-4 Logging in to the AHR.......................................................................................................................5-5Figure 5-5 Adding an AP zone.............................................................................................................................5-6Figure 5-6 Completing settings............................................................................................................................5-6Figure 5-7 Adding an AP user..............................................................................................................................5-7Figure 5-8 Logging in to the AP Manager...........................................................................................................5-9Figure 5-9 Configuring a zone...........................................................................................................................5-10Figure 5-10 Activating a zone............................................................................................................................5-11Figure 5-11 Configuring a zone.........................................................................................................................5-12Figure 5-12 Setting the list of AP frequencies...................................................................................................5-12Figure 5-13 Setting the list of AP scrambling codes..........................................................................................5-13Figure 5-14 Configuration confirmation............................................................................................................5-13Figure 6-1 Tracing management..........................................................................................................................6-3Figure 6-2 Execute Trouble Diagnose ..............................................................................................................6-4UAP2105User Guide FiguresIssue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.iii
TablesTable 3-1 LED on the UAP2105..........................................................................................................................3-3Table 3-2 Ports and buttons on the UAP2105......................................................................................................3-4Table 3-3 Performance specifications of the UAP2105.......................................................................................3-5Table 3-4 Technical specifications of the UAP2105............................................................................................3-6Table 5-1 Meanings of parameters.......................................................................................................................5-7Table 6-1 Commissioning AP Services................................................................................................................6-2Table 6-2 Alarm management options.................................................................................................................6-5Table 7-1 Communication ports used by the UAP2105.......................................................................................7-1UAP2105User Guide TablesIssue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.v
About This DocumentPurposeThis document describes the features, specifications, installation, commissioning, and routineoperation and maintenance of Huawei UAP2105 (hereafter referred to as AP).Product VersionThe following table lists the product version related to this document.Product Name Product VersionUAP2105 V300R011C90 Intended AudienceThis document is intended for:lSystem engineerslSite maintainerslNetwork administratorsChange HistoryFor changes in the document, see 1 Changes in the UAP2105 User Guide.Organization1 Changes in the UAP2105 User GuideThis describes the changes in the UAP2105 User Guide.2 Safety PrecautionsThis describes the safety precautions that are taken when installing, operating and maintainingthe equipment manufactured by Huawei.3 Introduction to the UAP2105Developed in compliance with the protocols of R99/R4/R5/R6 FDD, the UAP2105 providesUMTS radio network access for home and Small Office and Home Office (SOHO) users.UAP2105User Guide About This DocumentIssue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.1
4 Installing the UAP2105This describes how to install the UAP2105, accessories, and related cables.5 Configuring the UAP2105This describes how to configure the UAP2105 through the WebUI or the AP Manager.6 Routine Operation and Maintenance of the UAP2105This describes how to perform commissioning, routine maintenance, and software managementof the AP after installation and configuration.7 Communication Ports Used by the UAP2105ConventionsSymbol ConventionsThe symbols that may be found in this document are defined as follows.Symbol DescriptionIndicates a hazard with a high level of risk, which if notavoided,will result in death or serious injury.Indicates a hazard with a medium or low level of risk, whichif not avoided, could result in minor or moderate injury.Indicates a potentially hazardous situation, which if notavoided,could result in equipment damage, data loss,performance degradation, or unexpected results.Indicates a tip that may help you solve a problem or savetime.Provides additional information to emphasize or supplementimportant points of the main text. General ConventionsThe general conventions that may be found in this document are defined as follows.Convention DescriptionTimes New Roman Normal paragraphs are in Times New Roman.Boldface Names of files, directories, folders, and users are inboldface. For example, log in as user root.Italic Book titles are in italics.Courier New Examples of information displayed on the screen are inCourier New.About This DocumentUAP2105User Guide2 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
Command ConventionsThe command conventions that may be found in this document are defined as follows.Convention DescriptionBoldface The keywords of a command line are in boldface.Italic Command arguments are in italics.[ ] Items (keywords or arguments) in brackets [ ] are optional.{ x | y | ... } Optional items are grouped in braces and separated byvertical bars. One item is selected.[ x | y | ... ] Optional items are grouped in brackets and separated byvertical bars. One item is selected or no item is selected.{ x | y | ... }*Optional items are grouped in braces and separated byvertical bars. A minimum of one item or a maximum of allitems can be selected.[ x | y | ... ]*Optional items are grouped in brackets and separated byvertical bars. Several items or no item can be selected. GUI ConventionsThe GUI conventions that may be found in this document are defined as follows.Convention DescriptionBoldface Buttons, menus, parameters, tabs, window, and dialog titlesare in boldface. For example, click OK.>Multi-level menus are in boldface and separated by the ">"signs. For example, choose File > Create > Folder . Keyboard OperationsThe keyboard operations that may be found in this document are defined as follows.Format DescriptionKey Press the key. For example, press Enter and press Tab.Key 1+Key 2 Press the keys concurrently. For example, pressing Ctrl+Alt+A means the three keys should be pressed concurrently.Key 1, Key 2 Press the keys in turn. For example, pressing Alt, A meansthe two keys should be pressed in turn. UAP2105User Guide About This DocumentIssue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.3
Mouse OperationsThe mouse operations that may be found in this document are defined as follows.Action DescriptionClick Select and release the primary mouse button without movingthe pointer.Double-click Press the primary mouse button twice continuously andquickly without moving the pointer.Drag Press and hold the primary mouse button and move thepointer to a certain position.About This DocumentUAP2105User Guide4 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
1 Changes in the UAP2105 User GuideThis describes the changes in the UAP2105 User Guide.03(2009-09-20)This is the second commercial release..Compared with issue 02(2009-07-10) of V300R011C90, this issue does not add contents.Compared with issue 02(2009-07-10) of V300R011C90, this issue incorporates the followingchanges:Topic Change DescriptionLogging in to the WebUI The user name andpassword for logging into the WebUI arechanged. Thedescription of setting theInternet Explorer 8.0compatibility is added. Compared with issue 02(2009-07-10) of V300R011C90, this issue does not delete contents.02(2009-07-10)This is the first commercial release.Compared with issue 01 (2009-05-30) of V300R011C90, this issue does not add contents.Compared with issue 01 (2009-05-30) of V300R011C90, this issue incorporates the followingchanges:UAP2105User Guide 1 Changes in the UAP2105 User GuideIssue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.1-1
Topic Change Description3.4.1 Performance Specifications of the UAP2105 The description of thecapacity and servicecapabilities of theUAP2105 is modified. Compared with issue 01 (2009-05-30) of V300R011C90, this issue does not delete contents.01 (2009-05-30)This is the first commercial release.1 Changes in the UAP2105 User GuideUAP2105User Guide1-2 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
2 Safety PrecautionsThis describes the safety precautions that are taken when installing, operating and maintainingthe equipment manufactured by Huawei.Following All Safety PrecautionsWhen installing, operating, and maintaining the devices, follow all instructions and precautionson the equipment and in this document for the sake of personal and equipment safety. Theindications such as Danger, Caution, and Note in the related documents are additionalinformation. They do not contain all the safety precautions for operations.Complying with the Local Safety RegulationsWhen operating devices, the personnel must comply with the local safety regulations.Installation RequirementsThe personnel installing and maintaining Huawei products should be trained. Before performingany operation such as device installation and maintenance, the personnel should be familiar withthe proper operation methods and safety precautions.lOnly trained and qualified personnel are allowed to install, operate, and maintain devices.lOnly qualified specialists are allowed to check and repair the device and remove the safetyfacilities.lOnly personnel that are certificated or authorized by Huawei are allowed to replace orchange the device or accessories (including software).lAny fault or error that might cause safety problems must be reported to the personnel incharge immediately.Safety of PersonnellDo not perform operation on the device and related cables during thunderstorms.lUnplug the device during thunderstorms.lBefore installing the device and related cables, unplug the device.lTake proper safety measures to protect your eyes and respiratory tract against the dustbefore drilling holes.UAP2105User Guide 2 Safety PrecautionsIssue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.2-1
lWear gloves before drilling holes.Device SafetylEnsure that the device is always kept in a dry environment and is protected against leakage.lLeave sufficient space around the device for heat dissipation. Do not block the air vents ofthe device.lPlace the device in a dry, ventilated, and dustfree place that is neither exposed to directsunlight nor close to heat or fire.lKeep the device far away from strong magnetic or electric fields.2 Safety PrecautionsUAP2105User Guide2-2 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
3 Introduction to the UAP2105About This ChapterDeveloped in compliance with the protocols of R99/R4/R5/R6 FDD, the UAP2105 providesUMTS radio network access for home and Small Office and Home Office (SOHO) users.3.1 Appearance of the UAP2105The UAP2105 has a case structure. It is elegant, harmonious, and stylish.3.2 LED on the UAP2105The UAP2105 has only one LED, which indicates the working status of the UAP2105.3.3 Ports and Buttons on the UAP2105This describes the ports and buttons on the UAP2105. The ports are used for the power supply,Ethernet cable, and SIM or USIM card. The RESTORE button is used to restore the loginpassword of the WebUI to the default password. The power switch is used to power on or poweroff the UAP2105.3.4 Specifications of the UAP2105This describes the performance specifications and technical specifications of the UAP2105.UAP2105User Guide 3 Introduction to the UAP2105Issue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.3-1
3.1 Appearance of the UAP2105The UAP2105 has a case structure. It is elegant, harmonious, and stylish.The UAP2105 is available in black or white. Figure 3-1 shows a black UAP2105.Figure 3-1 UAP2105 3.2 LED on the UAP2105The UAP2105 has only one LED, which indicates the working status of the UAP2105.Figure 3-2 shows the LED on the UAP2105.3 Introduction to the UAP2105UAP2105User Guide3-2 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
Figure 3-2 LED on the UAP2105 Table 3-1 describes the LED and its status.Table 3-1 LED on the UAP2105Status DescriptionON (red) No AP cell is set up, or an alarm of cell setup failure is generated.ON (blue) An AP cell is set up. No service is provided, and no interferenceexists in the signals of the cell.Blinking in red (ON for1s and OFF for 1s)Slight interference exists in the signals of an AP cell. TheUAP2105 works properly, but the quality of service (QoS)deteriorates.Blinking in red (ON for0.25s and OFF for 0.25s)Strong interference exists in the signals of an AP cell. TheUAP2105 cannot work properly.Blinking in blue (ON for1s and OFF for 1s)An AP cell is set up successfully, and services are being providedin the cell.Blinking in blue (ON for0.125s and OFF for0.125s)Software is being downloaded, or the system is being upgraded. UAP2105User Guide 3 Introduction to the UAP2105Issue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.3-3
3.3 Ports and Buttons on the UAP2105This describes the ports and buttons on the UAP2105. The ports are used for the power supply,Ethernet cable, and SIM or USIM card. The RESTORE button is used to restore the loginpassword of the WebUI to the default password. The power switch is used to power on or poweroff the UAP2105.Figure 3-3 shows the ports and buttons on the panel of the UAP2105.Figure 3-3 Ports and buttons on the UAP2105 Table 3-2 describes the ports and buttons on the UAP2105.Table 3-2 Ports and buttons on the UAP2105Port or Button DescriptionRESTORE Button for restoring the login password of the WebUI. After youpress the button for five seconds, Restore the AP to factory settings(including the IP address for AP local maintenance and the user nameand password for logging in to the WebUI).SIM SIM or USIM card holder, which is used for housing the SIM orUSIM card3 Introduction to the UAP2105UAP2105User Guide3-4 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
Port or Button DescriptionLAN Ethernet port for an Ethernet cablePWR Power socket, which is connected to the 12 V DC power adapterPower switch Used to power on or power off the UAP2105 3.4 Specifications of the UAP2105This describes the performance specifications and technical specifications of the UAP2105.3.4.1 Performance Specifications of the UAP2105This describes the performance specifications of the UAP2105 in terms of the frequency bands,maximum transmit power, number of TRXs, transmit and receive diversity, receiver sensitivity,and clock precision.3.4.2 Technical Specifications of the UAP2105This describes the technical specifications of the UAP2105.3.4.1 Performance Specifications of the UAP2105This describes the performance specifications of the UAP2105 in terms of the frequency bands,maximum transmit power, number of TRXs, transmit and receive diversity, receiver sensitivity,and clock precision.Performance SpecificationsTable 3-3 Performance specifications of the UAP2105Item SpecificationFrequency bands Frequency band RX band (MHz) TX band (MHz) BAND I (2100 MHz) 1920 to 1980 2110 to 2170 Band II (1900 MHz) 1850 to 1910 1930 to 1990 Band V (850 MHz) 824 to 849 869 to 894Maximumtransmit power13 dBm (20 mW)Capacity Only one TRX is supported.Only one cell is supported.A maximum of 20 UL channel elements (CEs) and 20 DL CEs issupported.UAP2105User Guide 3 Introduction to the UAP2105Issue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.3-5
Item SpecificationServicecapabilitiesCommon PS and CS services:lA maximum of four concurrent AMR services is supported.lA maximum of four concurrent VP services is supported.lA maximum of eight concurrent PS services is supported.lA maximum of four concurrent R99 384 kbit/s PS services issupported.lA maximum of four concurrent CS users is supported.lA maximum of four concurrent PS users is supported.HSDPA service:lThe maximum supported HSDPA rate is 3.6 Mbit/s or 7.2 Mbit/s. Thedefault value is 3.6 Mbit/s. The license can be used to control themaximum HSDPA rate of the UAP2105.l3GPP R99, R4, R5, and R6 services can be provided at the same time.lA maximum of four concurrent HSDPA users is supported.lA maximum of 10 HS-PDSCH codes is supported.HSUPA servicelThe maximum supported HSUPA rate is 1.44 Mbit/s.l3GPP R99, R4, R5, and R6 services can be provided at the same time.lA maximum of four concurrent HSUPA users is supported.lThe 10 ms Transmission Time Interval (TTI) over the E-DCH issupported.Transmit andreceive diversityNo transmit diversity or receive diversityReceiversensitivity-110 dBmClock precision ±0.1 ppm 3.4.2 Technical Specifications of the UAP2105This describes the technical specifications of the UAP2105.Technical SpecificationsTable 3-4 Technical specifications of the UAP2105Item SpecificationDimensions (Height x Width x Depth) 33 mm x 125 mm x 125 mmWeight 0.4 kg3 Introduction to the UAP2105UAP2105User Guide3-6 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
Item SpecificationPower consumption < 8 WAmbient temperature Working temperature: -5oC to +40oCStorage temperature: -40oC to +70oCRelative humidity 5% RH to 95% RHSpecifications of the power adapter Input voltage: 90 V AC to 264 V ACFrequency range: 47 Hz to 63 Hz UAP2105User Guide 3 Introduction to the UAP2105Issue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.3-7
4 Installing the UAP2105About This ChapterThis describes how to install the UAP2105, accessories, and related cables.4.1 Selecting a Position for Installing the UAP2105This describes the requirements for the installation position of the UAP2105.4.2 Installing the SIM or USIM CardThis describes how to install the SIM or USIM card. The data in the card enables the UAP2105to perform user authentication and then to connect the core network after the authentication issuccessful.4.3 Connecting UAP2105 CablesThis describes how to connect the power adapter of the UAP2105 and how to connect theEthernet cable based on the network topology of the UAP2105.UAP2105User Guide 4 Installing the UAP2105Issue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.4-1
4.1 Selecting a Position for Installing the UAP2105This describes the requirements for the installation position of the UAP2105.Requirements for the Installation PositionThe UAP2105, a home device, is installed indoor areas that are away from children, such asliving rooms or studies. It supports the tabletop or wall-mounted installation. The UAP2105mounted on a wall obtatains better coverage than that placed on a tabletop. Leave a minimumof 20 cm space around the UAP2105 for heat dissipation. When selecting a position for installingthe UAP2105, adhere to the following rules:lDo not place the AP near the window.lDo not cover or block the AP.lDo not overload the AP.lDo not place AP near a microwave oven.lDo not place the AP on an electrical device.lDo not directly blow hot wind to the AP.4.2 Installing the SIM or USIM CardThis describes how to install the SIM or USIM card. The data in the card enables the UAP2105to perform user authentication and then to connect the core network after the authentication issuccessful.PrerequisiteBefore installing the SIM or USIM card, power off the UAP2105 and disconnect the powercable.ProcedureStep 1 Insert the SIM or USIM card into the card holder, as shown in Figure 4-1.4 Installing the UAP2105UAP2105User Guide4-2 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
Figure 4-1 Installing the SIM or USIM card CAUTIONlWhile inserting the SIM or USIM card into the card holder, ensure that the notch on the SIMor USIM card faces the silkscreen.lDo not remove the SIM or USIM card while the UAP2105 is running. Otherwise, the APcell cannot be set up. After the SIM or USIM card is re-inserted, the UAP2105 cell isreestablished.----End4.3 Connecting UAP2105 CablesThis describes how to connect the power adapter of the UAP2105 and how to connect theEthernet cable based on the network topology of the UAP2105.ContextA power adapter and straight-through cable are delivered with the UAP2105 and are placed inthe external packing box.UAP2105User Guide 4 Installing the UAP2105Issue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.4-3
ProcedureStep 1 Connect the power adapter, as shown in Figure 4-2.Figure 4-2 Connecting the power adapter of the UAP2105 CAUTIONTo ensure that the UAP2105 runs properly, use the power adapter delivered with the UAP2105.Step 2 Connect the Ethernet cable.lIn PPPoE modeThe UAP2105 is connected to the Ethernet through an xDSL device, such as a modem,BAS, or DSLAM.If the Modemhas ...Then …Only one LAN port 1. Use Ethernet cables to connect the UAP2105 and thecomputer for local maintenance to idle LAN ports on a routeror switch.2. Connect the router or switch to a modem.For details on connections, see the documents delivered withthe router or switch.Figure 4-3 shows the cable connections when the modem hasonly one LAN port.NOTEIf no router is configured, you can directly connect the computer for localmaintenance to the modem to configure the modem, and then connectthe computer to the UAP2105 to configure the UAP2105. After themodem and the UAP2105 are configured, you can directly connect theUAP2105 to the LAN port on the modem.4 Installing the UAP2105UAP2105User Guide4-4 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
If the Modemhas ...Then …Multiple LAN ports Connect the UAP2105 to an idle LAN port on the modemthrough an Ethernet cable, as shown in Figure 4-4.The UAP2105 and the computer for local maintenance shouldbe connected to the same modem. Figure 4-3 Cable connections (with the modem having only one LAN port) Figure 4-4 Cable connections (with the modem having multiple LAN ports) CAUTIONIf a cable modem is used (Cable Modem is labeled on the housing of the modem), connectthe cables according to the documents delivered with the cable modem.lIn FE direct connection modeUAP2105User Guide 4 Installing the UAP2105Issue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.4-5
The UAP2105 is directly connected to the Ethernet through a device, such as a router. Thenumber of devices used in FE direct connection mode is smaller than the number of devicesused in PPPoE mode. As a result, the UAP2105 provides higher uplink and downlink rates.1. Connect the UAP2105 to an idle LAN port on the router through an Ethernet cable.The UAP2105 and the computer for local maintenance should be connected to thesame router.2. Connect the router to the Ethernet.For details on connections, see the documents delivered with the router.Figure 4-5 shows the cable connections in FE direct connection mode.Figure 4-5 Cable connections (in FE direct connection mode) Step 3 Check the cables to ensure that all connections are secure.----End4 Installing the UAP2105UAP2105User Guide4-6 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
5 Configuring the UAP2105About This ChapterThis describes how to configure the UAP2105 through the WebUI or the AP Manager.5.1 Initial ConfigurationThis describes how to configure the IP address of the AP and the connection mode through anADSL modem or router according to the network topology of the AP.5.2 Defining a Subscriber in the AHRThis describes how to define an AP subscriber in the AHR. To define an AP subscriber in theAHR, create an AP zone, and then add an AP user to the zone.5.3 Setting Parameters on the AP ManagerThis describes how to set AP parameters on the AP Manager. The parameter settings areapplicable to all APs managed by the AP Manager.UAP2105User Guide 5 Configuring the UAP2105Issue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.5-1
5.1 Initial ConfigurationThis describes how to configure the IP address of the AP and the connection mode through anADSL modem or router according to the network topology of the AP.5.1.1 PPPoE ModeThe PPPoE mode consists of PPPoE bridge mode and PPPoE route mode. Regardless of themode you choose, you need to set the parameters of the ADSL modem and the AP.5.1.2 FE Direct Connection ModeThis describes how to configure the IP address of the AP and the connection of the router in FEdirect connection mode.5.1.1 PPPoE ModeThe PPPoE mode consists of PPPoE bridge mode and PPPoE route mode. Regardless of themode you choose, you need to set the parameters of the ADSL modem and the AP.PrerequisitelYou have logged in to the WebUI. For details, see Logging in to the WebUI.lThe IP address of the computer is set on the 192.168.1.x network segment.ContextIn PPPoE bridge modelThe connection mode when an ADSL modem works in bridge mode and the applicationtype of the modem is set to Bridge Only is called PPPoE bridge mode. In PPPoE bridgemode, you need to enter the user name and password of each terminal connected to themodem to initiate PPPoE dial-up connections for authentication.In PPPoE route modelThe modem obtains the IP address and related information such as the IP address of thegateway and subnet mask from the BAS through PPPoE dial-up connections. After themodem passes the authentication, it is connected to Internet. In PPPoE route mode, themodem works in DHCP Server mode. Each terminal connected to the modem canautomatically obtain the IP address of the LAN from the modem without PPPoE dial-upconnections.ProcedurelIn PPPoE bridge mode1. Configure the ADSL modem.NOTETo set WAN Configuration of the ADSL modem in PPPoE bridge mode, set the applicationtype of the ADSL modem to Bridge Only and the connection of the ADSL modem to RFC2684 Bridge. The setting method varies according to the type of the ADSL modem. For details,see the document delivered with the ADSL modem.5 Configuring the UAP2105UAP2105User Guide5-2 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
2. Configure the AP. On the WebUI, choose Transfer Basic > NETMODE . ClickMod, set Net Mode to PPPOELINK, and then type the user name and password fora PPPoE dial-up connection, as shown in Figure 5-1.Figure 5-1 Configuring an AP NOTEAfter the networking mode of the AP is changed, the AP is automatically restarted. The existingconfigurations are not modified.lIn PPPoE route mode1. Configure the ADSL modem.NOTETo set WAN Configuration, NAT, and DNS of the ADSL modem in PPPoE route mode, setthe application type of the ADSL modem to PPPoE, NAT to NAPT, DNS to Allow, and DHCPto DHCP Server. The setting method varies according to the type of the ADSL modem. Fordetails, see the document delivered with the ADSL modem.2. Check the configuration of the AP. On the WebUI, choose Transfer Basic >NETMODE to check the configuration of the AP, as shown in Figure 5-2.Figure 5-2 Checking the configuration of the APUAP2105User Guide 5 Configuring the UAP2105Issue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.5-3
If ... Then …Net Mode is set to ETHIP and AUTOIP to ENABLEThe configuration is complete. End theoperation.NOTEWhen an AP is delivered, Net Mode is set toETHIP and AUTO IP to ENABLE bydefault. Therefore, in PPPoE route mode, itis not necessary to configure the AP.Net Mode is not set to ETHIP or AUTOIP to ENABLEGo to 3. 3. Configure the AP. On the WebUI, choose Transfer Basic > NETMODE . ClickMod and set Net Mode to ETHIP and AUTO IP to ENABLE.0----End5.1.2 FE Direct Connection ModeThis describes how to configure the IP address of the AP and the connection of the router in FEdirect connection mode.PrerequisitelYou have logged in to the WebUI. For details, see Logging in to the WebUI.lThe IP address of the computer is set on the 192.168.1.x network segment.ContextFigure 5-3 shows the FE direct connection mode.Figure 5-3 FE direct connection mode 5 Configuring the UAP2105UAP2105User Guide5-4 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
ProcedureStep 1 For details, see the description of PPPoE route mode in 5.1.1 PPPoE Mode.NOTEThe method of setting the router in FE direct connection mode is the same as the method of setting the ADSLmodem in PPPoE route mode.----End5.2 Defining a Subscriber in the AHRThis describes how to define an AP subscriber in the AHR. To define an AP subscriber in theAHR, create an AP zone, and then add an AP user to the zone.5.2.1 Adding a ZoneThis describes how to add an AP zone in the AHR. Before adding an AP zone, obtain theinformation about neighboring macro cells around the AP cell and the IP addresses of the APManager, AG, SeGW, and CLK used in the AP network.5.2.2 Adding a UserThis describes how to perform AP user management in the AHR, for example, add an AP userin the AHR.5.2.1 Adding a ZoneThis describes how to add an AP zone in the AHR. Before adding an AP zone, obtain theinformation about neighboring macro cells around the AP cell and the IP addresses of the APManager, AG, SeGW, and CLK used in the AP network.PrerequisitelYou have installed the AHR client that matches the version of the AHR server.lYou have obtained the IMSI of the SIM or USIM card used in the AP and the IP addressesof the AP Manager, AG, SeGW, and CLK used in the AP network.ProcedureStep 1 Start the AHR client, and then type the user name, password, and IP address of the AHR server,as shown in Figure 5-4.Figure 5-4 Logging in to the AHRUAP2105User Guide 5 Configuring the UAP2105Issue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.5-5
Step 2 Choose Area > AP Zone Management. The Zone Configuration page is displayed.Step 3 Click Add. The Add AP Zone dialog box is displayed, as shown in Figure 5-5.Figure 5-5 Adding an AP zone Step 4 Type the zone where the AP is located and set SCTP Port to the port ID that is the same as theport ID of the AG.Step 5 Click Next to set the IP addresses of the AP Manager, AG, SeGW, and CLK and the informationabout neighboring macro cells around the AP cell in sequence.Step 6 Confirm the settings, and then click Finish, as shown in Figure 5-6.Figure 5-6 Completing settings5 Configuring the UAP2105UAP2105User Guide5-6 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
----End5.2.2 Adding a UserThis describes how to perform AP user management in the AHR, for example, add an AP userin the AHR.ProcedureStep 1 Choose Service > AP User Management. The AP User Management page is displayed.Step 2 Click OK.The Add AP User page is displayed, as shown in Figure 5-7.Figure 5-7 Adding an AP user Table 5-1 describes the parameters.Table 5-1 Meanings of parametersParameter Input Value DescriptionIMSI IMSI of the SIM or USIMcard used in the AP-AP Zone Name Name of the zone configuredin the 5.2.1 Adding a ZoneName of the zone where theAP is locatedUAP2105User Guide 5 Configuring the UAP2105Issue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.5-7
Parameter Input Value DescriptionLocation Detect Mode Cell ID Location detection isperformed according to themacro cell reported by theAP. The location detection isused to check the validity ofthe AP.PLMNID Location detection isperformed according to thePLMN ID reported by theAP.IP Address Location detection isperformed according to theIP address reported by theAP.None No location detection isperformed for the AP.User Access Policy Close Only the UEs in the UEpermission list set in theAHR can connect to the APnetwork.Open All UEs under the APcoverage can connect to theAP network.PLMNID Display Information about theoperator that providesservicesWhen the PLMNIDDisplay switch is enabled onthe AP Manager and a UEcamps on the AP cell, theinformation about theoperator is displayed on theUE.SMS Content SMS content for locationindicationWhen the SMS Contentswitch is enabled on the APManager and a UE camps onthe AP cell, a messagecontaining the locationindication information is sentto the UE. Step 3 Type parameters (the parameters with red asterisks are mandatory), and then click OK. The APuser is added successfully.----End5 Configuring the UAP2105UAP2105User Guide5-8 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
5.3 Setting Parameters on the AP ManagerThis describes how to set AP parameters on the AP Manager. The parameter settings areapplicable to all APs managed by the AP Manager.5.3.1 Activating a ZoneBefore setting the parameters in a zone on the AP Manager, activate the zone.5.3.2 Setting Parameters in a ZoneSelect the zone in which parameters need to be set, and then set the APCELLAC, list of APfrequencies, and list of AP scrambling codes.5.3.1 Activating a ZoneBefore setting the parameters in a zone on the AP Manager, activate the zone.PrerequisitelYou have obtained the IP address, login user name, and password of the AP Manager.lYou have obtained the Mobile Network Code (MNC), Mobile Country Code (MCC), AirMobile Country Code (MCCAIR), Air Mobile Network Code (MNCAIR), and AirLocation Area Code Range (LACAIR) used by the AP.lYou have obtained the APCELLAC, list of frequencies, and list of scrambling codes in thezone where the AP is located.ProcedureStep 1 Open the Internet Explorer (IE), and then type the IP address and login port number (such as,http://185.22.61.79:8080/apm) of the AP Manager. The login dialog box is displayed, as shownin Figure 5-8.Figure 5-8 Logging in to the AP ManagerUAP2105User Guide 5 Configuring the UAP2105Issue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.5-9
Step 2 Type the user name, password, and verify code to log in to the AP Manager.NOTEThe default user name is admin, and the default password is 11111111.Step 3 Choose Configuration > Zone Configuration. The Zone Configuration page is displayed.Step 4 Select the zone in which parameters need to be set, as shown in Figure 5-9. Then, clickActivate.Figure 5-9 Configuring a zone Step 5 Set the parameters based on network planning, and then click Activate to activate the zone, asshown in Figure 5-10.5 Configuring the UAP2105UAP2105User Guide5-10 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
Figure 5-10 Activating a zone ----End5.3.2 Setting Parameters in a ZoneSelect the zone in which parameters need to be set, and then set the APCELLAC, list of APfrequencies, and list of AP scrambling codes.PrerequisiteThe zone has been activated.ProcedureStep 1 Choose Configuration > > Zone Configuration . The Zone Configuration page is displayed.Step 2 Select the zone in which parameters need to be set, as shown in Figure 5-11. Then, clickConfigure.UAP2105User Guide 5 Configuring the UAP2105Issue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.5-11
Figure 5-11 Configuring a zone Step 3 Select the target AP in the zone, and then click Next.Step 4 Choose APCELLFREQ from the left pane and set the list of AP frequencies, as shown inFigure 5-12.Figure 5-12 Setting the list of AP frequencies 5 Configuring the UAP2105UAP2105User Guide5-12 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
NOTEClick Add Configuration to add a frequency of the AP.Step 5 After completing the settings, click Confirm.Step 6 Choose APPSCODE from the left pane and set the list of AP scrambling codes, as shown inFigure 5-13.Figure 5-13 Setting the list of AP scrambling codes NOTEClick Add Configuration to add a frequency of the AP.Step 7 After completing the settings, click Confirm.Step 8 Choose APCELLAC from the left pane and set the APCELLAC of the AP.Step 9 After completing the settings, click Confirm.Step 10 Click Submit after the APCELLAC, list of AP frequencies, and list of AP scrambling codes areset. The configuration confirmation page is displayed, as shown in Figure 5-14.Figure 5-14 Configuration confirmationUAP2105User Guide 5 Configuring the UAP2105Issue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.5-13
Step 11 After confirming the settings, click Apply.----End5 Configuring the UAP2105UAP2105User Guide5-14 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
6 Routine Operation and Maintenance of theUAP2105About This ChapterThis describes how to perform commissioning, routine maintenance, and software managementof the AP after installation and configuration.6.1 Commissioning ServicesThis describes how to trace the Uu interface, Iu interface, and CDT messages to test the servicesoffered by the AP through the Trace Viewer tool of the Local Maintenance Terminal (LMT).6.2 Diagnosing FaultsThis describes how to diagnose the faults in the AP, faults at the radio network layer, and faultsat the transport network layer on the WebUI and how to view diagnosis results.6.3 Handling AlarmsThis describes how to manage AP alarms on the AP Manager. You can subscribe to alarms,query alarm logs, and query and monitor active alarms.6.4 Upgrading the SoftwareThis describes how to upgrade the AP software on the FTP server.6.5 Uploading AP Terminal FilesThis describes how to upload the AP log, configuration file, and performance file to the FTPserver through the AP Manager for future analysis, use, or query.UAP2105User Guide 6 Routine Operation and Maintenance of the UAP2105Issue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.6-1
6.1 Commissioning ServicesThis describes how to trace the Uu interface, Iu interface, and CDT messages to test the servicesoffered by the AP through the Trace Viewer tool of the Local Maintenance Terminal (LMT).PrerequisitelThe AP is powered on, and the AP cell is set up.lTwo functional UEs, UE 1 and UE 2, are ready.lIf the admission mode of the AP is set to Close or Group, the IMSIs of UE 1 and UE 2 areadded to the AP permission list.For details about how to configure the AP permission list, see the AHR Operator Guide.lA functional fixed-line phone is ready.lThe LMT that matches the AP version works properly.lThe CS and PS domains are functional.ContextTable 6-1 describes the basic tasks involved in service commissioning.Table 6-1 Commissioning AP ServicesTask Method Expected ResultTest voice call services. UE 1 or UE 2 originates avoice call to the fixed-linephone.The voice quality is goodwithout loud noise.UE 1 originates a voice call toUE 2.The voice quality is goodwithout loud noise.Test video call services. UE 1 originates a video call toUE 2.lThe voice is clear.lThe video is clear andfluent.lThe voice is synchronizedwith the video.Test PS services. Browse web pages and uploador download data through aUE.Web pages are browsednormally, and data is uploadedor downloaded successfullywithin the specified time. ProcedureStep 1 Log in to the LMT, and then choose Service > Trace Management > Interface Trace Taskto trace the Uu interface, Iu interface, and CDT messages, as shown in Figure 6-1.6 Routine Operation and Maintenance of the UAP2105UAP2105User Guide6-2 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
Figure 6-1 Tracing management Step 2 Power on the UE under the coverage of the AP cell. Check whether the UE can automaticallysearch for the AP cell during startup.If ... Then …The UE fails to search for the AP cell 1. Identify and rectify the fault. For details, seeFailure of the UE to Search for the APCell.2. Go to Step 3.The UE succeeds in searching for the APcellGo to Step 3.Step 3 Wait until the UE is under the coverage of the AP cell and the location update is complete.If the AP fails to access the AP cell, identify and rectify the faulty. For details, see Failure ofthe UE to Access the AP Cell.Step 4 Test the services provided by the AP.1. A UE originates a voice call to the fixed-line phone.2. UE 1 originates a voice call to UE 2.3. UE 1 originates a video call to UE 2.4. Browse web pages and upload or download data through a UE.----EndUAP2105User Guide 6 Routine Operation and Maintenance of the UAP2105Issue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.6-3
6.2 Diagnosing FaultsThis describes how to diagnose the faults in the AP, faults at the radio network layer, and faultsat the transport network layer on the WebUI and how to view diagnosis results.ProcedureStep 1 Log in to the WebUI. For details, see Logging in to the WebUI. Then, chooseTroubleDiagnose. The Execute Trouble Diagnose page is displayed, as shown in Figure6-2.Figure 6-2 Execute Trouble Diagnose Step 2 Set Diagnose Mode and determine the type of a fault.lEquipment Trouble Diagnose: indicates the faults in the AP.lWireless Trouble Diagnose: indicates the faults at the radio network layer.ltransfers Trouble Diagnose: indicates the faults at the transport network layer.Step 3 Set OutPut Mode and determine the output mode of the fault diagnosis result.lJust Show Abnormity Result: indicates that only fault diagnosis results are displayed.lShow All Result: indicates that all diagnosis results are displayed.6 Routine Operation and Maintenance of the UAP2105UAP2105User Guide6-4 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
Step 4 Click Start to diagnose the faults.After the fault diagnosis is complete, diagnosis results are displayed in the Trouble DiagnoseLog pane.----End6.3 Handling AlarmsThis describes how to manage AP alarms on the AP Manager. You can subscribe to alarms,query alarm logs, and query and monitor active alarms.ProcedureStep 1 Log in to the AP Manager, and then click the Fault tab. On the tab page, manage alarms.Table 6-2 describes alarm management options.Table 6-2 Alarm management optionsAlarm Management Option DescriptionAlarm Subscribe Subscribe to the alarms of an AP or maintainthe list of the APs that have subscribed toalarms. Active Alarm Monitor, ActiveAlarm Query, and Alarm Log Query areavailable for only the APs that subscribe toalarms.Active Alarm Monitor View the active alarms that are not cleared inreal time and delete the cleared active alarms.Active Alarm Query Query the active alarms reported to the APManager database by the AP. To query thedetailed information about an alarm, click on the left of the alarm.Alarm Log Query Query the alarm logs reported to the APManager database by the AP.Terminal Alarm Log Query Query the remaining alarm logs on the AP. Ifthe AP is offline, the AP Manager promptsoperation timeout. ----End6.4 Upgrading the SoftwareThis describes how to upgrade the AP software on the FTP server.UAP2105User Guide 6 Routine Operation and Maintenance of the UAP2105Issue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.6-5
PrerequisitelThe FTP server is available.Log in to the AP Manager, and then choose Software > File Server. On the FileServers tab page, check Status of the corresponding FTP server.–If Status of the FTP Server is ... Then …Available The AP Manager communicates with theFTP server normally.Unavailable The AP Manager cannot communicatewith the FTP server normally.lSelect the option button before theFTP server, and then click Modify.Configure the FTP server on thedisplayed File Server Informationpage. lThe target upgrade version of the AP is synchronized to the FTP server.Log in to the AP Manager, and then choose Software.–Choose File Server, and then query the version file of the FTP server on the File Serversand Versions tab page.–Choose Version, and then click Add to upload the version file. After the version file isuploaded successfully, the AP Manager synchronizes the file to the available FTP serverautomatically.lThe zone where the AP is located is in the zone list of the FTP server.Log in to the AP Manager, and then choose Software > File Server.–Select the FTP server on the File Servers tab page, and then query the zone list of thefile server in the File Server Information dialog box.–Configure the mapping between the zone and the FTP server on the Zone ServersConfiguration tab page.ProcedurelUpgrading a single AP1. Log in to the AP Manager, and then choose Software > Upgrade.2. In the Terminal List pane, select the AP to be upgraded, and then click Upgrade.3. The Terminal Upgrade page is displayed. On the page, set options related to theupgrade task.Option DescriptionUpgrade Version It refers to the target version that the AP software is upgradedto.ImmediatelyRebootIt enables you to determine whether the AP is rebootedimmediately after the software is downloaded successfully. 4. Click Submit to complete the settings.6 Routine Operation and Maintenance of the UAP2105UAP2105User Guide6-6 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
If You Set Immediately Reboot to ... Then …Yes The AP is rebooted immediately forupgrade after the software isdownloaded successfully.NOTERebooting the AP disrupts the servicesprovided by the AP.No After the software is downloadedsuccessfully, check whether servicesare provided, and then reboot the AP.lIf no service is provided, reboot theAP for upgrade immediately.lIf services are ongoing, reboot theAP for upgrade after services areperformed. lUpgrading APs in batches1. Log in to the AP Manager, and then choose Software > Batch Upgrade.2. The Task Information page is displayed. On the page, set options related to theupgrade task.Option DescriptionTarget Version It refers to the target version that the AP software isupgraded to.Immediately Reboot It enables you to determine whether the AP is rebootedimmediately after the software is downloadedsuccessfully.Allow Retry It enables you to determine whether the software isupgraded again when sending an upgrade commandfails.Triggering Mode It refers to the triggering mode for upgrading thesoftware. Options:lTimer: indicates that you can specify the time forperforming the upgrade.lImmediately: indicates that the software isupgraded immediately.lManual: indicates that the software is upgradedmanually.Valid Time It refers to the validity period of an upgrade task. Ifthe validity period expires, the software is notupgraded again even if the upgrade fails.If the upgrade mode is set to Timer, this option isenabled.UAP2105User Guide 6 Routine Operation and Maintenance of the UAP2105Issue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.6-7
Option DescriptionTime Setting It is used to specify the time for starting the upgrade.If the upgrade mode is set to Timer, this option isenabled. 3. Click Next. On the displayed page, select the target APs.You can select the target APs on the AP Manager in the following two ways:–Special Terminal: indicates that you directly select APs to be upgraded.–Special Condition: indicates that you select APs to be upgraded by specialconditions.4. Click Submit to complete the settings.If You Set Immediately Reboot to ... Then …Yes The AP is rebooted immediately forupgrade after the software isdownloaded successfully.NOTERebooting the AP disrupts the servicesprovided by the AP.No After the software is downloadedsuccessfully, check whether servicesare provided, and then reboot the AP.lIf no service is provided, reboot theAP for upgrade immediately.lIf services are ongoing, reboot theAP for upgrade after services areperformed. ----End6.5 Uploading AP Terminal FilesThis describes how to upload the AP log, configuration file, and performance file to the FTPserver through the AP Manager for future analysis, use, or query.PrerequisiteThe FTP server is available.Log in to the AP Manager, and then choose Software > File Server. On the File Servers tabpage, check Status of the corresponding FTP server.If Status of the FTP Server is ... Then …Available The AP Manager communicates with the FTPserver normally.6 Routine Operation and Maintenance of the UAP2105UAP2105User Guide6-8 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
If Status of the FTP Server is ... Then …Unavailable The AP Manager cannot communicate withthe FTP server normally.lSelect the option button before the FTPserver, and then click Modify. Configurethe FTP server on the displayed FileServer Information page. ProcedureStep 1 Log in to the AP Manager, choose Fault > Terminal Files, and then click Uploading Files.Step 2 The Uploading Files page is displayed. On the page, type the APEI of the AP whose terminalfiles need to be uploaded in the Serial NO. box and select a target file from the File Type drop-down list.The types of the AP terminal files to be uploaded are as follows:lConfiguration FilelPerformance FilelAlarm LogAlarm logs consist of CurrUserAlm.log, HisUserAlm.log, and OrigAlm.log. The AP savesa maximum of 10,000 OrigAlm.log entries, 50 CurrUserAlm.log entries, and 1,000HisUserAlm.log entries. After the number of saved entries reaches the threshold, the earliestentries are deleted so that follow-up entries can be saved.lRunning LogThe AP saves a maximum of 2,000 running log entries. After the number of saved entriesreaches 2,000, the earliest entries are deleted so that follow-up entries can be saved.lCore LogThe latest three core log entries for abnormal resetting of the AP are saved.Step 3 Click Uploading Files to upload the specified terminal files of the AP.If ... Then …View Files is displayed Click View Files. In the File List pane, Status indicatesthe uploading status of the file.View Files is not displayed, or amessage box is displayedThe connection to the FTP server through the APManager is faulty. Choose System > System Setting >Fault, and then reset the login information of the FTPserver. UAP2105User Guide 6 Routine Operation and Maintenance of the UAP2105Issue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.6-9
NOTETo view terminal files, click View Files, and store the terminal files on the local disk of the computeraccording to the displayed system message.The methods of viewing terminal files are the same. Choose Start > All Programs > Huawei LocalMaintenance Terminal, and then select the corresponding alarm browser tool. The following descriptiontakes the method of viewing alarm logs for example:1. Choose Start > All Programs > Huawei Local Maintenance Terminal > Alarmlog BrowserTool.2. Select the AP type and language type.3. Click OK.4. Select the alarm log to be viewed, and then click Open.----End6 Routine Operation and Maintenance of the UAP2105UAP2105User Guide6-10 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.Issue 03 (2009-08-20)
7 Communication Ports Used by the UAP2105Table 7-1 lists the communication ports used by the UAP2105.Table 7-1 Communication ports used by the UAP2105ProtocolSideAPortNumber atSideA(RX)Side B PortNumberat Side B(TX)Service RightsControlTCP UAP210580 WebUI 1024-65535WebUI port for local OM User nameandpasswordTCP UAP21056000 LMT,WebUIProxy1024-65535MML port for local OM User nameandpasswordTCP UAP21056006 LMT,WebUIProxy1024-65535Binary port for local OM User nameandpasswordTCP UAP21057547 APManager1024-65535TR-069 protocol port -TCP UAP2105500 SeGW 1024-65535Default IKE port of theIPSec-TCP UAP21054500 SeGW 1024-65535NAT protocol port of theIPSec-TCP UAP210533003CLKServer1024-65535Clock synchronization -UAP2105User Guide 7 Communication Ports Used by the UAP2105Issue 03 (2009-08-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.7-1

Navigation menu