Huawei Technologies EML-L29 Smart Phone User Manual Quick Start Guide

Huawei Technologies Co.,Ltd Smart Phone Quick Start Guide

UserManual.wiki >

Huawei Technologies >

EML L29 User Manual

User Manual

Quick Start GuideEML-L09EML-L29

Your Device at a GlanceBefore you start, let's take a look at your new device.lTo power on your device, press and hold the power buttonuntil the screen turns on.lTo power off your device, press and hold the power button,and then touch .lTo restart your device, press and hold the power button,and then touch .lPress and hold the power button for 10 or more seconds toforcibly restart your device./'$1234567891012111413Secondary microphone Rear cameraLaser sensor Flash / Colortemperature sensorEarpiece Primary microphoneUSB-C port / HeadsetjackSpeakerFingerprint scanner Power buttonVolume button Ambient light sensor /Optical proximitysensorFront camera Status indicator1

Getting StartedlDo not insert or remove the SIM card when your deviceis powered on.lEnsure that the card is correctly aligned and that thecard tray is level when you insert it into your device.lBe careful not to scratch your device or hurt yourselfwhen using the eject pin.lStore the eject pin out of the reach of children toprevent accidental swallowing or injury.lDo not use cut or modied SIM cards with your deviceas these may not be recognized and could damage thecard tray (slot).lIf your SIM card does not match your device, pleasecontact your carrier.Follow the instructions in the following gures to set up yourdevice. Please use the eject pin included.Single-SIM:1 2Dual-SIM:1 22

Dual Card Dual Standby SinglePass (dual-SIM devices only)Your device supports only dual card dual standby single pass,which means you cannot use both SIM cards for calls or dataservices simultaneously.lWhen you are on a call using SIM card 1, SIM card 2 cannotbe used to make or answer calls. If someone calls SIM card2, the caller will hear a voice message similar to "Thesubscriber you dialed is out of the service area" or "Thesubscriber you dialed cannot be connected for the moment,please try again later." The actual message will vary byservice provider.lWhen you are using SIM card 1's data service, SIM card 2'sdata service will be disabled.Your device's single pass feature helps reduce powerconsumption and increase your device's standby time. It is notrelated to your service provider's network conditions.You can go to Settings > Wireless & networks > Dual SIMsettings, and enable Enable call forwarding between SIMsto avoid the conicts mentioned above.3

For More InformationIf you encounter any problems while using your device, youcan obtain help from the following resources:lGo to Tips for function details and usage tips.lVisit http://consumer.huawei.com/en to view deviceinformation, frequently asked questions and otherinformation.lVisit http://consumer.huawei.com/en/support for the mostup-to-date contact information for your country or region.Go to Settings and touch System > About phone > Legal toview legal information for your product.Go to Settings and touch System > About phone > Legal >Safety information to view safety information for yourproduct.Go to Settings and touch System > About phone >Authentication info to view regulatory information for yourproduct.Go to Settings and touch System > Certication logos toview more information on certication logos for your product.All pictures and illustrations in this guide, including butnot limited to the product color, size, and display content,are for your reference only. The actual product may vary.Nothing in this guide constitutes a warranty of any kind,express or implied.4

Safety InformationPlease read all of the safety information carefully before usingyour device to ensure its safe and proper operation and tolearn how to dispose of your device properly.Operation and safetyl To prevent possible hearing damage, do notlisten at high volume levels for long periods.lUsing an unapproved or incompatible power adapter,charger, or battery may damage your device, shorten itslifespan, or cause a re, explosion, or other hazards.lIdeal operating temperatures are 0 °C to 35 °C. Idealstorage temperatures are -20 °C to +45 °C.lPacemaker manufacturers recommend that a minimumdistance of 15 cm be maintained between a device and apacemaker to prevent potential interference with thepacemaker. If using a pacemaker, hold the device on theside opposite the pacemaker and do not carry the device inyour front pocket.lKeep the device and the battery away from excessive heatand direct sunlight. Do not place them on or in heatingdevices, such as microwave ovens, stoves, or radiators.lObserve local laws and regulations while using the device.To reduce the risk of accidents, do not use your wirelessdevice while driving.lWhile ying in an aircraft or immediately before boarding,only use your device according to instructions provided. Useof a wireless device in an aircraft may disrupt wirelessnetworks, present a hazard to aircraft operation, or beillegal.lTo prevent damage to your device's parts or internalcircuits, do not use it in dusty, smoky, damp, or dirtyenvironments or near magnetic elds.lWhen charging the device, make sure the power adapter isplugged into a socket near the devices and is easilyaccessible.lUnplug the charger from electrical outlets and the devicewhen not in use.lDo not use, store or transport the device where ammablesor explosives are stored (in a gas station, oil depot, or5

chemical plant, for example). Using your device in theseenvironments increases the risk of explosion or re.lDispose of this device, the battery, and accessoriesaccording to local regulations. They should not be disposedof in normal household waste. Improper battery use maylead to re, explosion, or other hazards.Disposal and recycling informationThe crossed-out wheeled-bin symbol on your product, battery,literature or packaging reminds you that all electronic productsand batteries must be taken to separate waste collectionpoints at the end of their working lives; they must not bedisposed of in the normal waste stream with householdgarbage. It is the responsibility of the user to dispose of theequipment using a designated collection point or service forseparate recycling of waste electrical and electronic equipment(WEEE) and batteries according to local laws.Proper collection and recycling of your equipment helps ensureelectrical and electronic equipment (EEE) waste is recycled in amanner that conserves valuable materials and protects humanhealth and the environment, improper handling, accidentalbreakage, damage, and/or improper recycling at the end of itslife may be harmful for health and environment. For moreinformation about where and how to drop off your EEE waste,please contact your local authorities, retailer or householdwaste disposal service or visit the website http://consumer.huawei.com/en/.Reduction of hazardous substancesThis device and its electrical accessories are compliant withlocal applicable rules on the restriction of the use of certainhazardous substances in electrical and electronic equipment,such as EU REACH, RoHS and Batteries (where included)regulations. For declarations of conformity about REACH andRoHS, please visit our web site http://consumer.huawei.com/certication.EU regulatory conformanceBody worn operationThe device complies with RF specications when used nearyour ear or at a distance of 0.50 cm from your body. Ensurethat the device accessories, such as a device case and device6

holster, are not composed of metal components. Keep thedevice away from your body to meet the distance requirement.The highest SAR value reported for this device type whentested at the ear isEML-L09 0.76 W/kgEML-L29 0.76 W/kgAnd when properly worn on the body isEML-L09 1.26 W/kgEML-L29 1.26 W/kgStatementHereby, Huawei Technologies Co., Ltd. declares that this deviceis in compliance with the essential requirements and otherrelevant provisions of Directive 2014/53/EU.The most recent and valid version of the DoC (Declaration ofConformity) can be viewed at http://consumer.huawei.com/certication.This device may be operated in all member states of the EU.Observe national and local regulations where the device isused.This device may be restricted for use, depending on the localnetwork.Restrictions in the 2.4 GHz band:Norway: This subsection does not apply for the geographicalarea within a radius of 20 km from the centre of Ny-Ålesund.Restrictions in the 5 GHz band:According to Article 10 (10) of Directive 2014/53/EU, thepackaging shows that this radio equipment will be subject tosome restrictions when placed on the market in Belgium (BE),Bulgaria (BG), the Czech Republic (CZ), Denmark (DK),Germany (DE), Estonia (EE), Ireland (IE), Greece (EL), Spain (ES),France (FR), Croatia (HR), Italy (IT), Cyprus (CY), Latvia (LV),Lithuania (LT), Luxembourg (LU), Hungary (HU), Malta (MT),Netherlands (NL), Austria (AT), Poland (PL), Portugal (PT),Romania (RO), Slovenia (SI), Slovakia (SK), Finland (FI), Sweden(SE), the United Kingdom (UK), Turkey (TR), Norway (NO),Switzerland (CH), Iceland (IS), and Liechtenstein (LI).The WLAN function for this device is restricted to indoor useonly when operating in the 5150 to 5350 MHz frequencyrange.7

Frequency Bands and Power(a) Frequency bands in which the radio equipment operates:Some bands may not be available in all countries or all areas.Please contact the local carrier for more details.(b) Maximum radio-frequency power transmitted in thefrequency bands in which the radio equipment operates: Themaximum power for all bands is less than the highest limitvalue specied in the related Harmonized Standard.The frequency bands and transmitting power (radiated and/orconducted) nominal limits applicable to this radio equipmentare as follows:EML-L09 GSM900: 37 dBm, GSM1800: 34 dBm,WCDMA900/ 2100: 25.7 dBm, LTE Band1/3/7/8/20/28/32/34/38/40: 25.7 dBm, Wi-Fi2.4G: 20 dBm, Bluetooth: 20 dBm, Wi-Fi 5G:5150-5350 MHz: 23 dBm, 5470-5725 MHz: 30dBm, NFC: 60 dBuA/m at 10mEML-L29 GSM900: 37 dBm, GSM1800: 34 dBm,WCDMA900/ 2100: 25.7 dBm, LTE Band1/3/7/8/20/28/32/34/38/40: 25.7 dBm, Wi-Fi2.4G: 20 dBm, Bluetooth: 20 dBm, Wi-Fi 5G:5150-5350 MHz: 23 dBm, 5470-5725 MHz: 30dBm, NFC: 60 dBuA/m at 10mAccessories and Software InformationSome accessories are optional in certain countries or regions.Optional accessories can be purchased from a licensed vendoras required. The following accessories are recommended:Adapters: HW-050450E00 (X represents the different plugtypes used, which can be either C, U, J, E, B, A, I, R, Z or K,depending on your region)Batteries: HB396285ECWEarphones: MEND1632B729000, 1331-3301-6001-TC-296,WINDY-C, L99EP003-CS-HThe product software version is EML-L09: EML-L098.1.0.71(SP9C900) / EML-L29: EML-L29 8.1.0.71(SP9C900).Software updates will be released by the manufacturer to xbugs or enhance functions after the product has beenreleased. All software versions released by the manufacturerhave been veried and are still compliant with the relatedrules.All RF parameters (for example, frequency range and outputpower) are not accessible to the user, and cannot be changedby the user.8

For the most recent information about accessories andsoftware, please see the DoC (Declaration of Conformity) athttp://consumer.huawei.com/certication.FCC Regulatory ComplianceBody worn operationThe device complies with RF specications when used nearyour ear or at a distance of 1.50 cm from your body. Ensurethat the device accessories, such as a device case and deviceholster, are not composed of metal components. Keep thedevice away from your body to meet the distance requirement.Certication information (SAR)This device is also designed to meet the requirements forexposure to radio waves established by the FederalCommunications Commission (USA).The SAR limit adopted by the USA is 1.6 W/kg averaged overone gram of tissue. The highest SAR value reported to the FCCfor this device type complies with this limit.The highest SAR value reported to the FCC for this device typewhen using it at the ear isEML-L09 0.99 W/kgEML-L29 0.99 W/kgAnd when properly worn on the body isEML-L09 0.72 W/kgEML-L29 0.72 W/kgAnd when using the Wi-Fi hotspot function isEML-L09 0.92 W/kgEML-L29 0.92 W/kgFCC statementThis equipment has been tested and found to comply with thelimits for a Class B digital device, pursuant to Part 15 of theFCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmfulinterference to radio communications. However, there is noguarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to9

try to correct the interference by one or more of the followingmeasures:--Reorient or relocate the receiving antenna.--Increase the separation between the equipment and receiver.--Connect the equipment into an outlet on a circuit differentfrom that to which the receiver is connected.--Consult the dealer or an experienced radio/TV technician forhelp.This device complies with Part 15 of the FCC Rules. Operationis subject to the following two conditions: (1) this device maynot cause harmful interference, and (2) this device must acceptany interference received, including interference that maycause undesired operation.Caution: Any changes or modications to this device notexpressly approved by Huawei Technologies Co., Ltd. forcompliance could void the user's authority to operate theequipment.Industry Canada complianceBody worn operationThe device complies with RF specications when used nearyour ear or at a distance of 1.50 cm from your body. Ensurethat the device accessories, such as a device case and deviceholster, are not composed of metal components. Keep thedevice away from your body to meet the distance requirement.The highest SAR value reported to the IC for this device typewhen using it at the ear isEML-L09 0.99 W/kgEML-L29 0.99 W/kgAnd when properly worn on the body isEML-L09 0.72 W/kgEML-L29 0.72 W/kgIC StatementThis device complies with CAN ICES-3 (B)/NMB-3(B).This device complies with Industry Canada licence-exempt RSSstandard(s). Operation is subject to the following twoconditions: (1) this device may not cause interference, and (2)this device must accept any interference, including interferencethat may cause undesired operation of the device.Restrictions in the 5 GHz band:Within the 5.15 to 5.25 GHz band, UNII devices will berestricted to indoor operations to reduce any potential for10

harmful interference to co-channel Mobile Satellite System(MSS) operations.11

底边留5mm31509383_01The N-Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries.

Navigation menu