Huawei Technologies E5838 Wireless Modem User Manual English

Huawei Technologies Co.,Ltd Wireless Modem English

Contents

Users Manual

Thank you for choosing this Wireless Modem. Note: This manual briefly describes the appearance, the preparation and the process for installing/uninstalling. Getting to Know your Wireless Modem The following figures show the appearance of the Wireless Modem. The actual product may differ. n Micro SD card slot Hold the Micro SD card. o USB connector Connect to the USB interface of the PC or the charger. p Power switch Press and hold it to power on or off the Wireless Modem. q WiFi/WPS switch z Press it to enable or disable the WiFi (Wireless Fidelity). Press and hold it to enable or disable the WPS (Wi-Fi Protected Setup). z r Dial key Press and hold it to set up a connection by dialing up or tear down a connection. s Battery_button the battery cover. Press and hold it to open t Signal indicator z Off: The signal is inexistent. Fast blinking in rez d: The USIM/SIM card does not exist or the PIN code . n: The signal strength is strong. ireless Modem is in the roaming state. led. bled. S SPA (HSDPA/HSUPA) data service connected. is not verified. z Steady on and in red: The signal strength is weak. z Steady on and in yellow: The signal strength is mediumz Steady on and in greeu Roam indicator z Off: The Wireless Modem is not in the roaming state. z Blinking in red: The Wv WiFi indicator z Off: The WiFi and WPS are disabz Blinking: The WPS is enabled. z Steady on: The WiFi is enaw Mode indicator z Blinking in green: Registering with the 2G network. Double blinking in green: The network is inexistent. z Steady on and in green: 2G data service connected. z Blinking in blue: Registering with the 3G network. z z Steady on and in blue: WCDMA data service connected. z teady on and in cyan: H Battery indicator z Blinking: The battery is being charged. Fast blinkiz ng in red: The battery power level is very low acharged. nd need to be d in green: The battery power level is enough. ime to z z Steady on and in yellow: The battery power level is normal. Steady on and in red: The battery power level is weak. zz Steady on an Note: Press the Dial key and Power switch at the sz ame time. The device changes to the forcible downloading state. Press and hold WiFi/WPS switz ch and Power switch at the same trestore the factory defaults. If the device has not been accessed for 10 minutes, the WiFi is
automatically disabled and the device changes to the deep sleep state. When the device is in the deep sleep state, press any key to activate the come lightened. In 10s, the dem WiFi and the device. Then, the indicators beindicators go out. Preparing the Wireless MoUSIM/SIM Card and Battery z z are emoving the cards during an operation may damage the he device, and data stored on the cards may be Note: Keep the USIM/SIM card out of the reach of children. z The USIM/SIM card and its metal contacts can be easily damaged by scratching or bending. Ensure care when you carry, load or remove it. Do not remove the USIM/SIM card and the Micro SD card when theybeing used. Rcards as well as tcorrupted. Micro SD card SD card into the slot. . z e Micro SD card, open the rubber cap and press the Micro Micro SD card will pop up automatically. Then 1. Remove the rubber cap from the Micro SD card slot; then insert theMicro2. After inserting the Micro SD card completely, replace the rubber capNote: z Micro SD card is an optional accessory. If the Micro SD card is not provided in the package, you can buy one yourself. To remove thSD card gently. Now the take it out. Charging the Battery Method 1: Using the charger the Wireless m. an optional accessory. If the charger is not provided in the ackage, you can contact your device dealer to buy a compatible charger data cable. 1. Insert the plug of the charger into the USB connector ofMode2. Insert the other plug of the charger into a power socket. Note: Charger ispyourself. Method 2: Connecting to a PC for charging Connect the Wireless Modem and PC with the compatible Nease recharge it first. ote: z When you charge the battery for the first time, please charge it for a minimum of 12 hours. z The battery discharges even while not being used. If you have not used it for a long time, plz The charging time depends on the environmental temperature and the age of the battery.
z , throw or cause any kind of violent shock to the battery, or explosion z er time period than usual after being e it with a battery of the same type. e management program depends on the ing section takes 1. he OS (Operating System) automatically detects and recognizes the auto-run program does not respond, find the AutoRun.exe file in the un the program. 3. on wizard. ut icon of the management is ent program is launched automatically. desktop to launch the 1. nd the management program, and click Add/Remove program he un-installation to ensure that ninstalled. Do not strikeotherwise liquid leakage, body damage, overheating, firemay occur. The battery can be recharged but eventually wears out. z If the battery lasts for a shortcharged normally, replacInstallation Guide The procedure for installing thoperating system installed on your PC. The followWindows XP as an example. Installing the Management Program Connect the Wireless Modem to the PC. 2. Tnew hardware and starts the installation wizard. Note: Ifdriver path. Then double-click AutoRun.exe to r Follow the prompts of the installati4. After the program is installed, the shortcprogram is displayed on the desktop. Starting the Management Program After the Wireless Modem is installed, the management programlaunched automatically. Then every time the Wireless Modem is connected to the PC, the managemYou can also double-click the shortcut icon on the management program. Uninstalling the Management Program Choose Start > Control Panel. 2. Fito uninstall the management program. Note: It is recommended to restart the PC after tthe management program is completely uRemoving th ireless Modem e W1. Double-click in the system tray. The Unplug or Eject Hardware interface is displayed. Select the hardware related2. to the Wireless Modem and click Stop. en the prompt "It is safe to remove the device" is displayed, em, exit the management program. cenario hrough setting up dem is powered by the built-in USB cable. 3. Whremove the Wireless Modem. Note: Before removing the Wireless ModApplication sRouter Mode In this mode, you can use the wireless Internet service tthe WiFi connection when the Wireless Mobattery but not connected to a PC with the le. If the WiFi is mode. Modem Mode In this mode, you can use the modem-based Internet service byconnecting the Wireless Modem to the PC with the USB cabenabled, you can use the Internet service of the Router 2. he wireless network connection whose name is the same as ss Modem and double-click the Setting up the WiFi Connection 1. Select Start > Control Panel > Network Connections > Wireless Network Connection. Find out tthe network name of the Wirele
connection. 3. Enter the correct security key. Nz ame and security key used for WiFi A maximum of five wireless users can access the Wireless Modem at the same time. You can set up the WLAN with the access point (AP) function. Version: V100R001_01 Part Number: 31010AMM 4. Click Connect. ote: You can find the network nauthentication on the base of your Wireless Modem or contact your network service provider. z

Navigation menu