Huawei Technologies BTS3911B Pico BTS User Manual

Huawei Technologies Co.,Ltd Pico BTS

User Manual

BTS3911BBTS3911BV100R010C10Installation Guide Issue: Draft ADate: 2015-01-20HUAWEI TECHNOLOGIES CO., LTD.
Installation ToolsRubberUtility knifeMarkerCable cutter Wire sDiagonal pliersESD gloves Torque wresize: 1Protective gloves-Hammer drill (Ø6, Ø8 or Ø12 bore) Ladder VacuumMeasuring tape Torque wrench for SMA connectors2r mallet Socket wrench (M6) LeveltripperRJ11 crimping tool Power cable crimping toolench (bore 0 mm)Phillips torque screwdrivercrown saw (Ø60 bore) (M4 to M6)--Network cable testerm cleanerMultimeter2Copyright © Huawei Technologies Co., Ltd. 2015. All rights reserved.
BTS3911BProduct IntroductionAppearance DimeThe BTS3911B uses internal antennas.bPort PortsPortMicroMiniURGPSP&EPSEAppearance and Dimensions Port Port-DATAPoE3ensionsDescriptionDescriptionSD Anchor slot for the Micro SD card used fordeploymentUSB Port for clock outputSPort for clock synchronizationPort for transmission and power supplyDescriptionDescriptionPower port that supplies power to the PSEAData input port that connects to transmission equipment of an operatorPoE output port that connects to the BTS3911B3
Installation ScenariosWall-mounted Installation•The wall must have a bearing capacity of at leThe wall must have a bearing capacity of at le• The screws must be torqued to 1.5 N·m and • The thickness of the wall must be less than ththrough an existing plate.• If the wall is too thick, use a customer-providezBy drilling holes zThrough an existinCeiling-mounted Installation• The ceiling (such as concrete ceiling) must haweight of the BTS3911B.zBy drilling holes zThrough an• The screws must be torqued to 1.5 N·m and w• The thickness of the ceiling must be less thanthrough an existing plate.Keel-mounted InstallationThe BTS3911B can be installed on a U-shaped, ddi it i tThfllifidepending on site requirements. The following figceiling.4east four times the weight of the BTS3911B.east four times the weight of the BTS3911B.work properly without causing cracks on the wall.he bolt length (45 mm) to allow for installation ed installation plate.ng plate zBy using a customer-provided installation plateave a bearing capacity of at least four times the n existing plate zBy using a keelwork properly without causing cracks on the wall.n the bolt length (45 mm) to allow for installation T-shaped, H-shaped, or other shaped keel, ill t t k ltdi tlltigure illustrates keel-mounted installation on a 4
Clearance RequirementszFor a BTS3911BInstallation Environment RequirementsOperating Environment RequirementsgSpecifications RequirementsOperating temperature -5 ºC to +40ºCRelative humidity 5% RH to 95% RHAltitude-60 m to +1800 m1800 mto 4000 m• The BTS3911B cannot be installed near air cappliances.• The BTS3911B cannot be installed near a strOther Requirements1800 mto 4000 m• The BTS3911B cannot be installed near placoutdoor air conditioner units, water pipes, piprunoff. • The installation must be protected against raiwhere the BTS3911B is installed.• The installation position must be far away froflammable or explosive substances, and elecp,• The BTS3911B must be installed in a dry, we• If the BTS3911B is installed in parking areas well ventilated.5zFor a PSEsRemarks--The BTS3911B works properly under the condition.From the altitude of 1,800 m, the maximum operating temperature drops by 1ºCeach time the altitude increases byconditioner outlet or near other heat-generating rong heat source of any kind.temperature drops by 1C each time the altitude increases by 220 m.gyces where water may leak or drip, such as near pelines, and roofs with water leaks or dripping in. No window exists at either side of the wall om high voltage, highly corrosive devices, ctromagnetic interference.gell-ventilated, and dustproof place.or basements, the installation position must be 5
Installation ProcessRemove the backup ESN label from the BTS3911Before installation, record the ESN, which will bthe backup ESN label, photograph it.Obtaining the ESNRecord the ESN by following instructions providedRecord the ESN by following instructions providedcommissioning personnel. Keep the backup ESN 6B packing box.be used during commissioning. Before removing d in Appendix 3 and report the ESN to the BTS3911Bd in Appendix 3 and report the ESN to the BTS3911B label secure.6
BTS3911B can be installed on a wall or ceiling dInstalling a BTS3911BzWall- or ceiling-mounted installation(1) Mounting bracket(2) Screws (M3.5X35)Mounting Kits(3) Plastic expansion sleeve(4) Flat washerInstalling a BTS3911B on a WallDrill holes and installplastic expansion sleevesInMark anchor points(1) Wall (2) Mounting bracket(3) Anchor pointsInstalling a BTS3911B on a CeilingDrill holes and installplastic expansion sleevesMark anchor pointsInstalling a BTS3911B on a Ceiling(1) Wall (2) Mounting bracket(3) Anchor points7irectly or by using a plate or keel.zInstallation on a plate or keel(1) Mounting bracket(2) V clamp(3) Bolt (M4X35)(3) Bolt (M4X35)(4) Bolt (M4X36)stall mounting kits Install the BTS3911B on the wallInstall mounting kits Install the BTS3911B on the ceiling7
Install mouMark anchor pointsInstalling a BTS3911B on a PlateOn a ceiling plate (for example, daughter board (1) Plate(2) Mounting bracket(3) Anchor pointsUse a hammer drill with Ф6 bore to drill holesOn a ceiling plate (for example gypsum board)Partially install mUse a crown saw to drill a hole (diameter: 60-65 mm)On a ceiling plate (for example, gypsum board) S ti kit t th ili l tSecure mounting kits to the ceiling plate8nting kits Install the BTS3911B on the ili l ton the ceiling) capable of being screwedceiling plateincapable of being screwedmounting kits Lead the U-shaped metal plate through the hole on the ceilingincapable of being screwedI t ll th BTS3911B th ili l tInstall the BTS3911B on the ceiling plate8
Install mounMark anchor pointsInstalling a BTS3911B on a KeelPlate U-shaped keelUse a hammer drill with Ф12 bore to drill holesU-shaped metal plateUse a hammer drill with Ф12 bore to drill holesInstalling the PSE and Its CablesPlace the PSE against the wall, level it in the The PSE can be installed only on an indoor wall.Installing the PSEginstallation position, and mark anchor pointsDrill holes and install expansion boltsInstall the PSEInstalling the BTS3911B CableszI t lli Eth t blzI t lli RzInstalling an Ethernet cablezInstalling an R9nting kits Install the BTS3911B on the plate.Installing CablesEPower portGPS i l bl(1) Ethernet cable(2) PSE power cableGPS signal cable9
Installation CheckSN Check Item1Th i ll i i i f h1The installation position conforms to the eng2 The BTS3911B is securely installed.3In wall-mounted scenarios, the holes on the expansion bolt assemblies. In addition, the m4The surface of the BTS3911B is neat and clenameplates are correct, legible, and completIn the wall-mounted scenario, the holes of th5 expansion bolt assemblies. In addition, the msteadily. 6None of power cables or signal cables is shodamaged or broken. 7 The power cables and PGND cables are bou8 The connectors of the signal cables are intac9Labels are correct legible and complete at bAfter you unpack a BTS3911B, you must power it on withinmaintenance, you must restore power to the BTS3911B wiPower-on Check9Labels are correct, legible, and complete at bCheck Process1iidi d l iineering design and meets clearance requirements.mounting bracket are well aligned with the holes of the mounting bracket is secured on the wall evenly and tightly. ean. The external paint is intact. The labels, tags, and te.e mounting bracket are well aligned with the holes of the mounting bracket is secured on the wall evenly and ort-circuited or reverse connected. All cables are not und and routed separately from other cables.ct and securely connected. The signal cables are intact.both ends of each cablen 24 hours. If you power off the BTS3911B for ithin 24 hours. both ends of each cable.Checking the Indicator StatusIf… Then…3GPP blinks white (on for 1s and off for 1s) The BTS3911B is running tlCPRI is steady whiteWIFI blinks white (on for 1dfff1)correctly.1s and off for 1s)LINK is steady white• During the BTS3911B startup, there is no need to observe the indicator status.• During a start, the BTS3911B reads and writes the flash and therefore the indicators blinking quickly NOTEmay blink irregularly for 1-2 seconds, which does not affect services.0
Appendix 3: ESN collection templateNoSiteSite NameThe ESN collection template is used to record the instainstallation stage to facilitate subsequent commissioninNo.Site NumberSite NameESNSample xx BTS3911BNote: This template is essential to the engineering stagmultiple devices are installed within a short distance. Tnetwork to access. Please carefully maintain this tempHUAW1HUAWHLocation Informationallation position and ESN of the site at the initial ng and maintenance. Location Informationxx floor, xx building, xx mansion ge and subsequent maintenance, especially when This is because the template defines the radio plate.WEI TECHNOLOGIES CO LTD1WEI TECHNOLOGIES CO., LTD.Huawei Industrial Base Bantian Longgang Shenzhen 518129People's Republic of Chinawww.huawei.com
           Regulatory Compliance Statement  BTS3911B       0682   Issue: 01  Date:2015-7-6  HUAWEI TECHNOLOGIES CO., LTD.
 Issue    (01) Huawei Proprietary and Confidential                                     Copyright © Huawei Technologies Co., Ltd. i    Copyright © Huawei Technologies Co., Ltd. 2010. All rights reserved. No  part  of  this  document  may  be  reproduced  or  transmitted in  any  form  or  by  any  means  without  prior  written consent of Huawei Technologies Co., Ltd.  Trademarks and Permissions   and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders.  Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document  are  provided  "AS  IS"  without  warranties,  guarantees  or  representations  of  any  kind,  either  express  or implied. The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute the warranty of any kind, express or implied.     Huawei Technologies Co., Ltd. Address: Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China Website: http://www.huawei.com Email: support@huawei.com
  1 Regulatory Compliance Statement  Issue    (01) Huawei Proprietary and Confidential                                     Copyright © Huawei Technologies Co., Ltd. 1-1  1 Regulatory Compliance Statement About This Chapter 1.1    Declaration of Conformity to European Directives 1.1 Declaration of Conformity to European Directives Figure 1-1 Declaration of Conformity to European Directives
1 Regulatory Compliance Statement    1-2 Huawei Proprietary and Confidential                                     Copyright © Huawei Technologies Co., Ltd. Issue    ()
  2 Regulatory Compliance Information  Issue    (01) Huawei Proprietary and Confidential                                     Copyright © Huawei Technologies Co., Ltd. 2-1  2 Regulatory Compliance Information About This Chapter 2.1    Regulatory Compliance Standards 2.2    European Regulatory Compliance 2.3    U.S.A Regulatory Compliance                                                                                     2.4    Canada Regulatory Compliance 2.5  Japanese Regulatory Compliance 2.6  CISPR 22 Compliance   2.7  China RoHS hazardous substance table 2.8  India RoHS hazardous substance table 2.9  Other Markets 2.1 Regulatory Compliance Standards Product complies with the standards listed in Table 2-1.
2 Regulatory Compliance Information    2-2 Huawei Proprietary and Confidential                                     Copyright © Huawei Technologies Co., Ltd. Issue    (01)  Table 2-1 Regulatory compliance standards Discipline Standards EMC  CISPR22 Class B  CISPR24  EN55022 Class B  EN50024  ETSI EN 301 489 Class B  CFR 47 FCC Part 15 Class B  FCC Part 2  FCC Part 22  FCC Part 24  ICES 003 Class B/Class A  AS/NZS CISPR22 Class B  GB9254 Class B  VCCI Class B  CNS 13438 Class B  IEC61000-6-1  IEC61000-6-3  EN61000-6-1  EN61000-6-3 Safety  IEC 60950-1  IEC60950-22  IEC/EN60215  IEC/EN41003  EN 60950-1  UL 60950-1  CSA C22.2 No 60950-1  AS/NZS 60950.1  BS EN 60950-1  IS 13252  GB4943 Laser safety  FDA rules, 21 CFR 1040.10 and 1040.11  IEC60825-1, IEC60825-2, EN60825-1, EN60825-2  GB7247
  2 Regulatory Compliance Information  Issue    (01) Huawei Proprietary and Confidential                                     Copyright © Huawei Technologies Co., Ltd. 2-3  Discipline Standards RF  ETSI EN 301 908    ETSI EN 300 328    ETSI EN 301 893  FCC Part 2  FCC Part 24  FCC Part 27  RSS-133  RSS-139 Health  ICNIRP Guideline  1999-519-EC  EN 50385  OET Bulletin 65  FCC Part 1  IEEE Std C95.1  EN 60215  RSS-102 Environmental protection  2011/65/EU (RoHS)  EC NO. 1907/2006 (REACH)  2002/96/EC (WEEE) Grounding  ITU-T K.27  ETSI EN 300 253
2 Regulatory Compliance Information    2-4 Huawei Proprietary and Confidential                                     Copyright © Huawei Technologies Co., Ltd. Issue    (01)  Discipline Standards NOTE EMC: electromagnetic compatibility NEBS: Network Equipment Build Standard RF: radio frequency CISPR: International Special Committee on Radio Interference EN: European Standard ETSI: European Telecommunications Standards Institute CFR: Code of Federal Regulations FCC: Federal Communication Commission IEC: International Electrotechnical Commission AS/NZS: Australian/New Zealand Standard VCCI: Voluntary Control Council for Interference CNS: Chinese National Standard UL: Underwriters Laboratories CSA: Canadian Standards Association BS: British Standard IS: Indian Standard GR: General Requirement FDA: Food and Drug Administration BTS: Base Transceiver Station GSM: Global System for Mobile communications WLAN: wireless local area network ICNIRP: International Commission on Non-Ionizing Radiation Protection OET: Office of Engineering Technology IEEE: Institute of Electrical and Electronics Engineers RoHS: restriction of the use of certain hazardous substances  2.2   European Regulatory Compliance Product complies with the following European directives and regulations.  2004/108/EC (EMC)  2006/95/EC (low voltage)  1999/5/EC (R&TTE)  2011/65/EU (RoHS)  EC NO. 1907/2006 (REACH)  2002/96/EC (WEEE) Product complies with Directive 2002/95/EC, 2011/65/EU and other similar regulations from the countries outside the European Union, on the RoHS in electrical and electronic equipment. The  device  does  not  contain  lead,  mercury,  cadmium,  and  hexavalent  chromium  and brominated flame retardants (Polybrominated Biphenyls (PBB) or Polybrominated Diphenyl Ethers  (PBDE))  except  for  those  exempted  applications  allowed  by  RoHS  directive  for technical reasons.
  2 Regulatory Compliance Information  Issue    (01) Huawei Proprietary and Confidential                                     Copyright © Huawei Technologies Co., Ltd. 2-5  Product complies with Regulation EC NO. 1907/2006 (REACH) and other similar regulations from the countries outside the European Union. Huawei will notify to the European Chemical Agency (ECHA) or the customer when necessary and regulation requires.  Product  complies  with  Directive  2002/96/EC  on  waste  electrical  and  electronic  equipment (WEEE).  Huawei  is  responsible  for  recycling  its  end-of-life  devices,  and  please  contact Huawei local service center when recycling is required. Huawei strictly complies with the EU Waste Electrical and Electronic Equipment Directive (WEEE Directive) and electronic waste management regulations enacted by different countries worldwide. In addition, Huawei has established a system for recycling and reuse of electronic wastes, and it can provide service of dismantling and recycling for WEEE. By Huawei recycling system, the waste can be handled environmentally  and  the  resource  can  be  recycled  and  reused  fully,  which  is  also  Huawei WEEE  stratagem  in  the  word.  Most  of  the  materials  in  product  are  recyclable,  and  our packaging is designed to be recycled and should be handled in accordance with your local recycling policies.   In accordance with  Article 11(2)  in  Directive 2002/96/EC  (WEEE),  products  were marked with the following symbol: a cross-out wheeled waste bin with a bar beneath as below:    In order to avoid the possibility of exceeding the Europe radio frequency exposure limits, human proximity to the equipment shall not be less than 0.124 m 2.3 U.S.A Regulatory Compliance 2.3.1    Safety compliance Mark   2.3.2  FCC   2.3.1 Safety compliance Mark
2 Regulatory Compliance Information    2-6 Huawei Proprietary and Confidential                                     Copyright © Huawei Technologies Co., Ltd. Issue    (01)   2.3.2FCC   Product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  This device does not cause harmful interference.  This device must accept any interference received, including interference that may cause undesired operation. If this device is modified without authorization from Huawei, the device may no longer comply with FCC requirements for Class B digital devices. In that a case, your right to use the device may be limited by FCC regulations. Moreover, you may be required to correct any interference to radio or television communications at your own expense. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and radiates radio frequency energy. If it is not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user may take one or more of the following measures:  Reorient or relocate the receiving antenna.  Reinforce the separation between the device and receiver.  Connect the device into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio or TV technician for assistance.  In order to avoid the possibility of exceeding the 47CFR FCC Part 1 & OET Bulletin 65 radio frequency exposure limits, human proximity to the equipment shall not be less than   0.182 m 2.4 Canada Regulatory Compliance 2.4.1 RSS-Gen statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
  2 Regulatory Compliance Information  Issue    (01) Huawei Proprietary and Confidential                                     Copyright © Huawei Technologies Co., Ltd. 2-7  radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. 2.4.2 RSS-102 statement This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by Industrial Canada and meets the requirements for radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the Industrial Canada radio frequency exposure limits, human proximity to the equipment shall not be less than 0.235 m Cet appareil est conçu et fabriqué pour ne pas dépasser les limites d'émission pour l'exposition à la fréquence radio (RF) de l'énergie fixé par l'Industrielle Canada et répond aux exigences en matière de limites d'exposition aux rayonnements définies pour un environnement non contrôlé.   Afin d'éviter la possibilité de dépasser les limites d'exposition aux fréquences radio industrielle du Canada, la proximité humaine pour l'appareil nedoit pas être inférieure à 0.235 m  The device is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;   The worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in RSS-247 Section 6.2.2(3).   High-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.   2.5 Japanese Regulatory Compliance 2.5.1    VCCI  2.5.1VCCI Product complies with VCCI Class B    by Information Technology Equipment (ITE). The preceding translates as follows: This is a Class B product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI).If this product is used Near a radio or television receiver in a domestic environment. It may cause radio Interference.Install and use the equipment according to the instruction manual.
2 Regulatory Compliance Information    2-8 Huawei Proprietary and Confidential                                     Copyright © Huawei Technologies Co., Ltd. Issue    (01)  2.6 CISPR 22 Compliance Product complies with CISPR 22 for Class B by the ITE.     2.7 China RoHS hazardous substance table  This products described in this guide complies with “the Administration on the Control of Pollution Caused by Electronic Information Products” which is also called China RoHS 部件名称 产品中有害物质或元素的名称及含量 镉 铅 汞 六价铬 多溴联苯 多溴联苯醚 Frame 〇 ╳ 〇 〇 〇 〇 Alloy Parts 〇 ╳ 〇 〇 〇 〇 Power Adapter 〇 ╳ 〇 〇 〇 〇 Metal Fittings 〇 〇 〇 〇 〇 〇 PCBA 〇 ╳ 〇 〇 〇 〇 Capacitor 〇 ╳ 〇 〇 〇 〇 Other electronics 〇 ╳ 〇 〇 〇 〇 Screen 〇 〇 〇 〇 〇 〇 Solder 〇 ╳ 〇 〇 〇 〇 Cable ╳ ╳ 〇 〇 〇 〇 Plastic and Polymer 〇 ╳ 〇 〇 〇 ╳ Label 〇 〇 〇 〇 〇 〇 Battery 〇 〇 〇 〇 〇 〇 〇:表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T11363-2006 标准规定的限量要求以下。
  2 Regulatory Compliance Information  Issue    (01) Huawei Proprietary and Confidential                                     Copyright © Huawei Technologies Co., Ltd. 2-9  ╳:表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T11363-2006 标准规定的限量要求。     2.8 India RoHS hazardous substance table This products described in this guide complies with the “e-waste (Management and Handling) Rules, 2011”of India which is also called India RoHS.  Part Descriptions Restricted Substances in Product Cd Pb Hg Cr(VI) PBBs PBDEs Frame 〇 ╳ 〇 〇 〇 〇 Alloy Parts 〇 ╳ 〇 〇 〇 〇 Power Adapter 〇 ╳ 〇 〇 〇 〇 Metal Fittings 〇 〇 〇 〇 〇 〇 PCBA 〇 ╳ 〇 〇 〇 〇 Capacitor 〇 ╳ 〇 〇 〇 〇 Other electronics 〇 ╳ 〇 〇 〇 〇 Screen 〇 〇 〇 〇 〇 〇 Solder 〇 ╳ 〇 〇 〇 〇 Cable ╳ ╳ 〇 〇 〇 〇 Plastic and Polymer 〇 ╳ 〇 〇 〇 ╳ Label 〇 〇 〇 〇 〇 〇 Battery 〇 〇 〇 〇 〇 〇 〇: indicates that the content of the toxic and hazardous substance in all the Homogeneous Materials of the part is below the concentration limit requirement as described in the e-waste (Management and Handling) Rules, 2011. ╳: indicates that the content of the toxic and hazardous substance in at least one Homogeneous Material of the
2 Regulatory Compliance Information    2-10 Huawei Proprietary and Confidential                                     Copyright © Huawei Technologies Co., Ltd. Issue    (01)  part exceeds the concentration limit requirement as described in S in the e-waste (Management and Handling) Rules, 2011.    2.9 Other Markets For relevant compliance information/documentation for markets not mentioned above, please contact Huawei representative

Navigation menu