Huawei Technologies AP6510DN-AGN Outdoor Wireless LAN Access Point User Manual 20 1

Huawei Technologies Co.,Ltd Outdoor Wireless LAN Access Point 20 1

20. User Manual 1

AP6510DN-AGN-US Outdoor Wireless LAN Access PointQuick Start GuideHUAWEI TECHNOLOGIES CO., LTD.
     Huawei Technologies Co., Ltd.Address:     Huawei Technologies Co.,  Ltd.                   Bantian,Longgang                    Shenzhen 518129                   People’s Republic of China         Website:     http://enterprise.huawei.comCopyright © Huawei Technologies Co., Ltd. 2012. All rights reserved.No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.Trademarks and Permissions        and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.All other trademarks and trade names mentioned in this document are the property of their respective holders.NoticeThe purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied.The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this documentdo not constitute the warranty of any kind, express or implied.1
Symbol ConventionsThe symbols that may be found in this document are defined as follows.Symbol DescriptionNOTECAUTION Indicates a potentially hazardous situation, which if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.Provides additional information to emphasize or supplement important points of the main text.2Change HistoryChanges between document issues are cumulative. Therefore,the latest document issue contains all the changes in previous issues.Change in Issue 01 (2012-09-30)Initial commercial release.
AP6510DN-AGN-USQuick Start Guide技术支持Before performing Installation, confirm that the installation accessories and tools are available.Installation tools: Technical SupportHuawei Technologies Co., Ltd.Address:   Huawei Industrial Base                  Bantian,Longgang                  Shenzhen 518129                 People’s Republic of China         Website:   http://enterprise.huawei.comInstallation suiteExpansion boltM4X12 hexagon socket head cap screwHoop Installation accessories:Device OverviewPacking ListUnpack the equipment. Ensure that all items listed in the package list are included in the shipment. If any item is missing, contact the supplier.Ports and indicators5G antenna port   672.4G antenna port Connected to the feeder.Connected to the feeder.Item  DescriptionSNProduct functions31234114Item Quantity UnitAP device PCSPCSPCSInstallation suite1PCSNetwork port connector52Expansion bolt PCS62M4X12 hexagon socket head cap screwPCS10 1Item Quantity UnitPCSWarranty cardCertificate of ConformanceHoop71PCSQuick Start Guide (including the printed packing list)81PCS9Toxic or Hazardous Substance & Elements Declaration1PCS1234 5Item  DescriptionSNSYSWirelessDefault1SYS status indicator.2345LinkETH/POE portLink status indicator.Wireless status indicator.Used for Ethernet connections.Press and hold down the Reset button for 3 seconds to restore the factory settings and restart  the AP.6 677 Phillips screwdriver HammerMakerFlat-head screwdriver Diagonal pliers Adjustable wrenchESD gloves COAX crimping toolMeasuring tapeWire stripper RJ45 Crimping tool MultimeterLevelVacuum  cleaner Network cable testerHammer drillHex key6mm drillbitNo. No.
Installing an AP● Select an appropriate installation position and leave space above and around the device for cooling air circulation.● Outdoors Aps are used for hotspot coverage and often installed against walls or poles. The pole diameter is 48 mm to 114 mm.AP6510DN-AGN-US dimensions (unit: mm) without a backplane support. Recommended AP6510DN-AGN-US installation space (unit: mm).● Installing the AP6510DN-AGN-US against a Wall: 330 83306Hexagon socket head cap screwField strength场强示意1.   Fix the wall-mounting bracket to the wall, adjust the      installation position, and use the marker, level, and       measuring tape to mark the drilling positions where      expansion bolts are installed.2.   Use #8 drill bit to drill 35 mm to 40 mm deep holes in the       drilling positions and install expansion bolts. Screw the nut       into the expansion tube, hammer the expansion bolt into a       hole until the flat washer is flattened against the wall, and       remove the nuts, spring washer, and flat washer in order.Flat washerSpring washerNuts3.  Use four M4*12 hexagon socket head cap screws to fasten the wall-mounting bracket to the AP.4.  Pinch the wall-mounting bracket  on the expansion      bolts, and  fasten the flat washer, spring washer, and     nuts in order.5.  Slide the AP into the wall-mounting bracket to complete      installation.464mm37mm
Installing an AP上电调试3● Installing the AP6510DN-AGN-US against a vertical pole:Field strength场强示意NOTELock holeSecurity lock1.  Determine the AP installation position, slide the hoop     through the hole of the wall-mounting bracket and attach     it to the pole, And use the screwdriver to secure screws      on the hoop.2.   Slide the AP that has the connector fastened into the wall-      mounting bracket.● The procedure for installing the AP6510DN-AGN-US against a horizontal pole is similar to the procedure for installing the     AP6510DN-AGN-US against a vertical pole.●  Installing the Security LockTo prevent unauthorized personnel from moving the AP, lock the AP. The preceding figure shows the security lock. The carrier should purchase the security lock and determine the position for installing the security lock.5
Installing Cables     ● AP6510DN-AGN-US external cable arrangement drawing3.  Put the network cable through the hole on the waterproof PG connector.a b c d4.  Connect the RJ45 connector to the AP and secure the waterproof PG connector, as shown in figures b, c, and d.a b c dWaterproof PG connector● Connecting network cables         1.  Use a shield straight-through cable. Cut the cable of proper length based on the distance between the AP and the PSE              device, peel the insulation on both ends of the network cable,  and crimp the wires to RJ45 connectors.                2.  Make a network cable onsite according to the following pin assignment. Otherwise, the communication quality is               affected even if devices can be connected.X1 Pin12345678X2 Pin12345678Wire ColorWhite and orangeOrangeWhite and greenBlueWhite and blueGreenWhite and brownBrownFeed lineGround cableNetwork cableFeed lineFeed lineFeed line6● The network cables used are category-5 twisted pairs.● Ensure that the RJ45 connector is correctly Connected to the AP. Otherwise, the network cable may be  damaged.    Before removing the network cable, remove the waterproof PG connector, and then remove the RJ45 connector from    the AP.CAUTION
     Installing Cables● Connecting the feed line1.  The outdoor AP's antenna ports already have 5 KA surge protection capability. Generally, no surge protection devices      need to be installed; therefore, the antenna cables are directly connected to the AP's antenna ports.2.  If higher surge protection capability is required, the customer can purchase a surge protection device. When installing the     surge protection device, ensure that it is connected to a ground cable.aWaterproof adhesive tapeGround cableSurge protection devicecbWaterproof adhesive tapeFeed lineFeed lineConnecting the ground bar● Connecting the ground cable   ● Cut the cable of proper length, the M4 connector is connected to the AP and the M6 connector is connected to the       ground bar.7●  When no antenna is installed on the 5G antenna interface, cover the interface with a dustproof cap and wrap the     dustproof cap with insulating tape and waterproof tape.●  Wrap the feed line using one-layer PVC black insulation tape, three-layer waterproof adhesive tape, and then three-layer    PVC black insulation tape.●  Stretch the waterproof adhesive tape evenly and ensure that the upper layer of the tap overlaps 1/2 of the lower layer.     Each layer should be attached tightly.●  Wrap the three-layer waterproof adhesive tape from bottom to up, from up to bottom, and from bottom to up in order.NOTE
     Installing Cables  Requirements for laying out ground cables:1. All ground cables must be connected to a ground bar.2. The ground cable cannot be led in aerially, but buried in the earth or arranged indoor.3. Both ends of the external conductor of the coaxial cable and those of the insulation of the shielded cable should    have good electric contact with the metal shell of the equipment they connect to.4. Ground cables must be separated from signal cables to reduce interference between them.5. Do not add any switch or fuse on the ground cable.6. Do not use another device for an electrical connection with the ground cable.7. All metal components in the shell must be securely connected to the ground cable.8Keep the screw properly and install it again after pressing the Reset button. CAUTION● Pressing the Reset Button   The Reset button on an outdoor AP is protected by a waterproof screw. Before pressing the Reset button, remove the    waterproof screw. CAUTION
     Power-on 2连接线缆Technical SpecificationsNOTE255mm×255mm×83mm2.2KgItem Description Operating temperature –  40°C to +60°C Storage temperature0% to 100%  Relative humidityAltitude 70 kPa to 106 kPaWeightDimensions (W x D x H)– 40°C to +70°CPressure PoE power supply -48V – 60 m to 4000 m When the altitude is between 1800 m and 4000 m, the operating temperature decreases by 1°C each time the altitude increases by 220 m.9SYS   WirelessLink DescriptionInformation TypeSteady greenSteady redBlinking greenBlinking once every 2sSteady or Blinking greenOffBlinking greenOffThe system is working properly.The system fails to load the DRAM or system software.The device is being started.Blinking once every 2sThe system is working properly. However, the Ethernet is not connected. Radios are disabled and no user is connected to the AP.The system is working properly, but the Ethernet is not connected. The AP has wireless users connected to the 2.4 GHz band and is transmiting data. The indicator blinks more quickly when more packets are being transmitted.Off The system is working properly, the Ethernet is connected, and radios are disabled. The indicator blinks more quickly when more data is being transmitted.Blinking yellow The system is working properly, but the Ethernet is not connected. The AP has wireless users connected to the  5 GHz band and is transmiting data. The indicator blinks more quickly when more packets are being transmitted.The system is working properly, but the Ethernet is not connected. The AP has wireless users connected to the 2.4 GHz and 5 GHz bands and is transmiting data.Blinking green The system is working properly, and the Ethernet is connected. The AP has wireless users connected to the 2.4 GHz band and is transmiting data. The indicator blinks more quickly when more packets are being transmitted.Blinking yellow The system is working properly, and the Ethernet is connected. The AP has wireless users connected to the 5 GHz band and is transmiting data. The indicator blinks more quickly when more packets are being transmitted.The AP has wireless users connected to the 2.4 GHz and 5 GHz bands and is transmiting data. The indicator blinks more quickly when more packets are being transmitted.Blinking green and yellow alternatelyBlinking green and yellow alternatelyThe AP6510DN-AGN-US supports the PoE function that complies with 802.3at. Power on the AP6510DN-AGN-US and check the indicator status to determine the system running status.Running andconnectionStartup statusNA NANA NANA NA
     Logging In to the Router10After an AP is powered on, you can log in to the AP using the following methods.1. Logging In to the AP Using TelnetThis section describes how to log in to the AP using Telnet. After logging in to the AP, you can configure the AP using commands.1. Logging In to the AP Using Telnet     This section describes how to log in to the AP using Telnet. After logging in to the AP, you can configure the AP using      Commands.Procedure     Step 1 Connect a PC to the uplink port of the AP with a network cable. Figure 1-1 shows the location of the AP's uplink                      port.                        Figure 1-1 Location of the AP's uplink portStep 2     Configure a static IP address for the PC. The IP address must be on the network segment 192.168.0.1/24                 (The IP address should not be same as the AP's default IP address 192.168.0.1.) and the subnet mask is                 255.255.255.0.                 After the configuration is complete, run the ping 192.168.0.1 command on the PC to check whether the PC                 can be pinged. If the ping operation succeeds, the connection is set up successfully. If the ping operation fails,                 The connection fails to be set up. Check whether the network cable works properly. Step 3     Access the command line window on the PC. For example, if the PC runs Windows XP, choose Start > Run                 And enter cmd in the displayed dialog box. Step 4     Run the telnet 192.168.0.1 command to log in to the AP.Step 5     Enter the default user name and password admin. If the user view is displayed, you have logged in                 Successfully.                When you log in for the first time, the following page is displayed:                  Username: admin                  Password:                  Enterprise AP:                 ----EndNo. Port1ETH/PoE1NOTERun the exit command to exit from the Telnet window. When the system fails to exit from the Telnet window:● If you logged in to the AP from an AC or a switch, press Ctrl+T to return to the AC or switch view. This operation does    not affect the AP operation.● If you logged in to the AP from a PC, directly close the Telnet window. This operation does not affect the AP operation.
     O: Indicates that the concentration of the hazardous substance contained in all the homogeneous materials of this part is      below the limit requirement of the SJ/T 11363-2006 standard.X: Indicates that the Concentration of the hazardous substance contained in all the homogeneous materials of this part is    above the limit requirement.Hazardous SubstancesPb Hg Cd Cr6+ PBB PBDEPartMechanical partBoard/circuit moduleSignal cableCable connectorPower adapterAuxiliary equipmentO O O O OO O O O OO O O O OO O O O OO O O O OO O O O ODeclaration on Hazardous Substances in Electronic Information ProductsQUALIFICATION CARD11OOOOOO
     Warranty CardThank you for choosing HUAWEI Technologies Co., Ltd-a leading telecom solution provider. To get better services, please read this warranty card carefully, fill in the required information and preserve this card in good condition.Preserve well. No reissueDealer´s Seal: Limited WarrantySubject to the exclusions contained below, Huawei Technologies CO., Ltd. (hereinafter referred to as Huawei) warrants its access terminals (“Products”) to be free from defects in materials and workmanship under normal consumer usage for one year from the date of purchase of the product ("Warranty period"). During the warranty period,a Huawei authorized service partner shall remedy defects in materials and workmanship free of charge.Special Notice:1.  The warranty card shall be applicable only after being stamped by the dealer.2.  The warranty card must be preserved in good condition and free of any scratch or alteration.3.  To claim such service for defects that are not included in The following exclusion terms, the warranty card and the     invoice that records the product serial number shall be presented to a Huawei authorized service  partner. Exclusions:In any of the following cases, the warranty card becomes unenforceable or inapplicable without prior notice:1.  The defects are caused by improper handling in transportation and assembly.  2.  The defects are caused by the fact that the product is dismantled or altered by anyone that is not from a Huawei      authorized service partner.  3.  The defects are caused by the fact that the product is used in a harsh environment that is not suitable for the operation      of the product.  4.  The defects are caused by any force majeure including but not limited to fire, earthquake, lightning and tsunami.5.  The defects are caused by the fact that the product is used or handled improperly, roughly or not as instructed in the      applicable User Guide.6.  The normal wear and tear, including but not limited to the normal wear and tear of the shell and the power module, shall      not be covered by the limited warranty.7.  The warranty card is altered or illegible, or the product serial number recorded on the warranty card is inconsistent with     the actual one imprinted or labeled on the product.In any case that is not covered by this limited warranty or should the warranty expire,Huawei shall charge for the service(s) claimed for the products if the product is still remediable.Huawei preserves the right for interpretation of this limited warranty.Your NameAddress/Postal CodeTelephoneProduct TypeProduct Serial NumberPurchase DateInvoice NumberDealer NameDealer´s Address/TelephoneHuawei Industrial Base, Bantian, Longgang,Shenzhen 518129, People's Republic of Chinahttp://enterprise.huawei.comHuawei Technologies Co., Ltd.12
 HUAWEI TECHNOLOGIES CO., LTD.Huawei Industrial BaseBantian, LonggangShenzhen 518129People's Republic of China http://enterprise.huawei.com

Navigation menu