Honeywell WFSMM Wireless Monitor Module User Manual SLC Gateway Notifier

Honeywell International Inc. Wireless Monitor Module SLC Gateway Notifier

Exhibit D Users Manual per 2 1033 b3

PRELIMINARYN0P/N LS10036-000NF-E:N0 ECN xx-xxxDocument LS10036-000NF-E10/10/2013 Rev:Notifier Wireless Sensor NetworkLS10036-000NF-EUser Manual
2 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013Fire Alarm & Emergency Communication System LimitationsWhile a life safety system may lower insurance rates, it is not a substitute for life and property insurance!An automatic fire alarm system—typically made up of smoke detectors, heat detectors, manual pull stations, audible warning devices, and a fire alarm control panel (FACP) with remote notifi-cation capability—can provide early warning of a developing fire. Such a system, however, does not assure protection against property damage or loss of life resulting from a fire. An emergency communication system—typically made up of an automatic fire alarm system (as described above) and a life safety communication system that may include an autonomous control unit (ACU), local operating console (LOC), voice commu-nication, and other various interoperable communication meth-ods—can broadcast a mass notification message. Such a system, however, does not assure protection against property damage or loss of life resulting from a fire or life safety event. The Manufacturer recommends that smoke and/or heat detectors be located throughout a protected premises following the recommendations of the current edition of the National Fire Protection Association Standard 72 (NFPA 72), manufacturer's recommendations, State and local codes, and the recommendations contained in the Guide for Proper Use of System Smoke Detectors, which is made available at no charge to all installing dealers. This document can be found at http://www.systemsensor.com/appguides/. A study by the Federal Emergency Management Agency (an agency of the United States government) indicated that smoke detectors may not go off in as many as 35% of all fires. While fire alarm systems are designed to provide early warning against fire, they do not guarantee warning or protection against fire. A fire alarm system may not provide timely or adequate warning, or simply may not function, for a variety of reasons: Smoke detectors may not sense fire where smoke cannot reach the detectors such as in chimneys, in or behind walls, on roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level or floor of a building. A second-floor detector, for example, may not sense a first-floor or basement fire. Particles of combustion or “smoke” from a developing fire may not reach the sensing chambers of smoke detectors because:• Barriers such as closed or partially closed doors, walls, chim-neys, even wet or humid areas may inhibit particle or smoke flow. • Smoke particles may become “cold,” stratify, and not reach the ceiling or upper walls where detectors are located. • Smoke particles may be blown away from detectors by air outlets, such as air conditioning vents. • Smoke particles may be drawn into air returns before reach-ing the detector. The amount of “smoke” present may be insufficient to alarm smoke detectors. Smoke detectors are designed to alarm at var-ious levels of smoke density. If such density levels are not cre-ated by a developing fire at the location of detectors, the detectors will not go into alarm. Smoke detectors, even when working properly, have sensing limitations. Detectors that have photoelectronic sensing cham-bers tend to detect smoldering fires better than flaming fires, which have little visible smoke. Detectors that have ionizing-type sensing chambers tend to detect fast-flaming fires better than smoldering fires. Because fires develop in different ways and are often unpredictable in their growth, neither type of detector is necessarily best and a given type of detector may not provide adequate warning of a fire. Smoke detectors cannot be expected to provide adequate warn-ing of fires caused by arson, children playing with matches (especially in bedrooms), smoking in bed, and violent explosions (caused by escaping gas, improper storage of flammable materi-als, etc.). Heat detectors do not sense particles of combustion and alarm only when heat on their sensors increases at a predetermined rate or reaches a predetermined level. Rate-of-rise heat detec-tors may be subject to reduced sensitivity over time. For this reason, the rate-of-rise feature of each detector should be tested at least once per year by a qualified fire protection specialist. Heat detectors are designed to protect property, not life. IMPORTANT! Smoke detectors must be installed in the same room as the control panel and in rooms used by the system for the connection of alarm transmission wiring, communications, signaling, and/or power. If detectors are not so located, a devel-oping fire may damage the alarm system, compromising its abil-ity to report a fire. Audible warning devices such as bells, horns, strobes, speakers and displays may not alert people if these devices are located on the other side of closed or partly open doors or are located on another floor of a building. Any warning device may fail to alert people with a disability or those who have recently consumed drugs, alcohol, or medication. Please note that:• An emergency communication system may take priority over a fire alarm system in the event of a life safety emergency.• Voice messaging systems must be designed to meet intelligi-bility requirements as defined by NFPA, local codes, and Authorities Having Jurisdiction (AHJ).• Language and instructional requirements must be clearly dis-seminated on any local displays.• Strobes can, under certain circumstances, cause seizures in people with conditions such as epilepsy. • Studies have shown that certain people, even when they hear a fire alarm signal, do not respond to or comprehend the meaning of the signal. Audible devices, such as horns and bells, can have different tonal patterns and frequencies. It is the property owner's responsibility to conduct fire drills and other training exercises to make people aware of fire alarm signals and instruct them on the proper reaction to alarm sig-nals. • In rare instances, the sounding of a warning device can cause temporary or permanent hearing loss. A life safety system will not operate without any electrical power. If AC power fails, the system will operate from standby batteries only for a specified time and only if the batteries have been properly maintained and replaced regularly. Equipment used in the system may not be technically compat-ible with the control panel. It is essential to use only equipment listed for service with your control panel. Telephone lines needed to transmit alarm signals from a prem-ises to a central monitoring station may be out of service or tem-porarily disabled. For added protection against telephone line failure, backup radio transmission systems are recommended. The most common cause of life safety system malfunction is inadequate maintenance. To keep the entire life safety system in excellent working order, ongoing maintenance is required per the manufacturer's recommendations, and UL and NFPA stan-dards. At a minimum, the requirements of NFPA 72 shall be fol-lowed. Environments with large amounts of dust, dirt, or high air velocity require more frequent maintenance. A maintenance agreement should be arranged through the local manufacturer's representative. Maintenance should be scheduled monthly or as required by National and/or local fire codes and should be per-formed by authorized professional life saftety system installers only. Adequate written records of all inspections should be kept. Limit-D-1-2013
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 3Installation PrecautionsAdherence to the following will aid in problem-free installation with long-term reliability:WARNING - Several different sources of power can be connected to the fire alarm control panel. Disconnect all sources of power before servicing. Control unit and associ-ated equipment may be damaged by removing and/or insert-ing cards, modules, or interconnecting cables while the unit is energized. Do not attempt to install, service, or operate this unit until manuals are read and understood. CAUTION - System Re-acceptance Test after Software Changes: To ensure proper system operation, this product must be tested in accordance with NFPA 72 after any pro-gramming operation or change in site-specific software. Re-acceptance testing is required after any change, addition or deletion of system components, or after any modification, repair or adjustment to system hardware or wiring. All compo-nents, circuits, system operations, or software functions known to be affected by a change must be 100% tested. In addition, to ensure that other operations are not inadvertently affected, at least 10% of initiating devices that are not directly affected by the change, up to a maximum of 50 devices, must also be tested and proper system operation verified. This system meets NFPA requirements for operation at 0-49º C/32-120º F and at a relative humidity 93% ± 2% RH (non-condensing) at 32°C ± 2°C (90°F ± 3°F). However, the useful life of the system's standby batteries and the electronic com-ponents may be adversely affected by extreme temperature ranges and humidity. Therefore, it is recommended that this system and its peripherals be installed in an environment with a normal room temperature of 15-27º C/60-80º F. Verify that wire sizes are adequate for all initiating and indi-cating device loops. Most devices cannot tolerate more than a 10% I.R. drop from the specified device voltage. Like all solid state electronic devices, this system may operate erratically or can be damaged when subjected to light-ning induced transients. Although no system is completely immune from lightning transients and interference, proper grounding will reduce susceptibility. Overhead or outside aerial wiring is not recommended, due to an increased susceptibility to nearby lightning strikes. Consult with the Technical Ser-vices Department if any problems are anticipated or encoun-tered. Disconnect AC power and batteries prior to removing or inserting circuit boards. Failure to do so can damage circuits. Remove all electronic assemblies prior to any drilling, filing, reaming, or punching of the enclosure. When possible, make all cable entries from the sides or rear. Before making modifi-cations, verify that they will not interfere with battery, trans-former, or printed circuit board location. Do not tighten screw terminals more than 9 in-lbs. Over-tightening may damage threads, resulting in reduced terminal contact pressure and difficulty with screw terminal removal. This system contains static-sensitive components. Always ground yourself with a proper wrist strap before han-dling any circuits so that static charges are removed from the body. Use static suppressive packaging to protect electronic assemblies removed from the unit.Follow the instructions in the installation, operating, and pro-gramming manuals. These instructions must be followed to avoid damage to the control panel and associated equipment. FACP operation and reliability depend upon proper installation.Precau-D1-9-2005HARSH™, NIS™, and NOTI•FIRE•NET™ are all trademarks; and Acclimate® Plus, FlashScan®, NION®, NOTIFIER®, ONYX®, ONYXWorks®, UniNet®,VeriFire®, and VIEW® are all registered trademarks of Honeywell International Inc.HARSH™ is a trademark; and Acclimate®, FlashScan®, NION®, andVIEW® are all registered trademarks of Honeywell International Inc. MULTI-NET™, Multi-Net Manager™, Unimode Network™, Unimode NetworkManager™, and Uni-Tility™ are trademarks of Tyco Integrated Security. Echelon® is a registered trademark and LonWorks™ is a trademark of EchelonCorporation. ARCNET® is a registered trademark of Datapoint Corporation. Microsoft® and Windows® are registered trademarks of the MicrosoftCorporation. ©2013 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited.
4 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013Software DownloadsIn order to supply the latest features and functionality in fire alarm and life safety technology to our customers, we make frequent upgrades to the embedded software in our products. To ensure that you are installing and programming the latest features, we strongly recommend that you download the most current version of software for each product prior to commissioning any system. Contact Technical Support with any questions about software and the appropriate version for a specific application. Documentation FeedbackYour feedback helps us keep our documentation up-to-date and accurate. If you have any comments or suggestions about our online Help or printed manuals, you can email us.Please include the following information:•Product name and version number (if applica-ble)•Printed manual or online Help•Topic Title (for online Help)•Page number (for printed manual)•Brief description of content you think should be improved or corrected•Your suggestion for how to correct/improve documentationSend email messages to:FireSystems.TechPubs@honeywell.comPlease note this email address is for documentation feedback only. If you have any technical issues, please contact Technical Services.
Table of ContentsPRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 5Table of ContentsSection 1: About This Guide....................................................................................................81.1: Purpose ..........................................................................................................................................................81.2: Assumed Knowledge .....................................................................................................................................81.3: Site Survey.....................................................................................................................................................81.4: Abbreviations and Meanings .........................................................................................................................9Section 2: FWSG..................................................................................................................... 102.1: Description...................................................................................................................................................102.2: Agency Approvals .......................................................................................................................................102.2.1: FCC....................................................................................................................................................102.3: Specifications...............................................................................................................................................112.3.1: Environmental Specification .............................................................................................................112.4: Installing FWSG ..........................................................................................................................................112.4.1: Before Installing ................................................................................................................................112.5: Mounting & Wiring .....................................................................................................................................122.5.1: Mounting ...........................................................................................................................................122.5.2: Wiring................................................................................................................................................142.5.3: FWSG Powered from SLC................................................................................................................152.5.4: FWSG Powered from an External +24VDC Source .........................................................................162.6: Configuration and Programming .................................................................................................................172.6.1: Without a PC-based Configuration Tool ...........................................................................................17Create a New Profile ............................................................................................................................17Assign a Previously Created Profile Using a Distributor.....................................................................18Removing a Profile...............................................................................................................................18Create Mesh Network...........................................................................................................................182.6.2: With a PC-based Configuration Tool ................................................................................................19Assigning Profile with PC Tools..........................................................................................................19Removing Profile with PC Tools .........................................................................................................20Mesh Formation with PC Tools ...........................................................................................................212.6.3: Profile Distribution............................................................................................................................212.6.4: SLC Configuration ............................................................................................................................222.7: Operations....................................................................................................................................................222.7.1: FWSG Modes Of Operation ..............................................................................................................22Start Up.................................................................................................................................................22Factory Default.....................................................................................................................................23Profile Configured ................................................................................................................................23Mesh Formation....................................................................................................................................23Initial Mesh Optimization.....................................................................................................................23Normal Mode........................................................................................................................................24Rescue Mode ........................................................................................................................................24Mesh Optimization ...............................................................................................................................24Bootloader ............................................................................................................................................242.7.2: Magnet Sensor Activations................................................................................................................24Profile Magnetic Sensor .......................................................................................................................24Mesh Formation Magnetic Sensor........................................................................................................242.7.3: LED Indications.................................................................................................................................242.7.4: Lock/Unlock FWSG..........................................................................................................................28Lock/Unlock FWSG through FACP ....................................................................................................28Lock/Unlock FWSG through PC tools.................................................................................................28Password Reset.....................................................................................................................................292.7.5: Weak Link Trouble Reporting...........................................................................................................29Disabling Trouble Reporting at the FWSG Using PC Tools ...............................................................29Disabling Trouble Reporting in the Panel ............................................................................................302.7.6: Collapse Network Command.............................................................................................................30
Table of Contents6 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013Collapsing Mesh Network Using PC Tools .........................................................................................30Collapsing Mesh Network in the Panel ................................................................................................312.7.7: Silence Network Command...............................................................................................................31Silencing Mesh Network Using PC Tools............................................................................................31Silencing Mesh Network in the Panel ..................................................................................................322.7.8: Multiple Wireless Sensor Network Installation Restrictions.............................................................332.7.9: Avoiding RF Interference ..................................................................................................................332.7.10: Trouble States ..................................................................................................................................342.7.11: History Events .................................................................................................................................36FWSG History Entries..........................................................................................................................36Section 3: Devices .................................................................................................................. 383.1: Description...................................................................................................................................................38Subsystem Overview ............................................................................................................................38FWD-200P- Wireless Photoelectric Smoke Detector (FCC ID AUBWFSSD). ............................... 38FWD-200ACCLIMATE- Wireless Acclimate (FCC ID AUBWFSSD) .......................................... 38FWH-200ROR135- Wireless Rate of Rise Heat Detector (FCC ID AUBWFSSD) ......................... 38FWH-200FIX135- Wireless Fixed Heat Detector (FCC ID AUBWFSSD) ..................................... 38FW-MM- Wireless Monitor Module (FCC ID AUBWFSMM) . ..................................................... 383.2: Agency Approvals .......................................................................................................................................383.2.1: FCC....................................................................................................................................................383.3: Specifications...............................................................................................................................................393.4: Installing Devices.........................................................................................................................................393.5: Mounting & Wiring......................................................................................................................................393.6: Configuration and Programming .................................................................................................................393.6.1: Assigning Profiles..............................................................................................................................40Assigning Profile Using PC Tools........................................................................................................40Assigning Profile to a Device with an FWSG or Distributor ...............................................................41Transfer Profile from an FWSG/Distributor to Detector..................................................................... 41Transfer Profile from an FWSG/Distributor to Module ...................................................................... 413.6.2: Distributor Mode ...............................................................................................................................42Converting a Device into a Distributor.................................................................................................42Converting a Distributor Back into a Device .......................................................................................423.6.3: Mesh Formation.................................................................................................................................43Repeater ................................................................................................................................................433.6.4: Restoring a Device to Factory Default ..............................................................................................43Removing Profiles without PC-based Configuration Tool...................................................................43Removing Profile with PC Tools..........................................................................................................433.7: Device Operations........................................................................................................................................443.7.1: Modes of Operation ...........................................................................................................................44Factory Default .....................................................................................................................................44Profile Assigned....................................................................................................................................44Bootloader.............................................................................................................................................45Distributor.............................................................................................................................................45Mesh Participant ...................................................................................................................................45Mesh Formation Mode ........................................................................................................................ 45Initial Mesh Optimization Mode ......................................................................................................... 45Normal Mode....................................................................................................................................... 45Rescue Mode ....................................................................................................................................... 453.7.2: LED Indications.................................................................................................................................453.7.3: Trouble States ....................................................................................................................................49Trouble States with Fire Protection ......................................................................................................49Class A Fault ....................................................................................................................................... 49Weak Link ........................................................................................................................................... 49Low Battery ......................................................................................................................................... 49Trouble States without Fire Protection .................................................................................................49Tamper................................................................................................................................................. 49
Table of ContentsPRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 7Duplicate Address ............................................................................................................................... 50No Answer........................................................................................................................................... 50Jamming .............................................................................................................................................. 50Device Initialization ............................................................................................................................ 503.7.4: Background Events............................................................................................................................51Pre-Class A Fault..................................................................................................................................51Device Drop..........................................................................................................................................51Weak Link ............................................................................................................................................51Section 4: USB Adapter..........................................................................................................524.1: Introduction..................................................................................................................................................524.2: Agency Approvals ......................................................................................................................................524.2.1: FCC....................................................................................................................................................524.3: Specifications...............................................................................................................................................534.3.1: Electrical Specifications ...................................................................................................................534.3.2: Serial Communication Specification................................................................................................534.3.3: Mechanical Specifications................................................................................................................534.3.4: Environmental Specifications............................................................................................................534.4: Driver Installation........................................................................................................................................54Appendix A: Site Survey ........................................................................................................58A.1: Description..................................................................................................................................................58A.1.1: Conducting Site Survey at the Job Site ............................................................................................58Link Quality Test..................................................................................................................................58Basic Requirements............................................................................................................................. 58Conduct a Link Test ............................................................................................................................ 58Results of Link Test..............................................................................................................................59Tasks After Link Test.......................................................................................................................... 60Link Quality Test and RF Scan Test ....................................................................................................60Conduct a Link Test .............................................................................................................................60Results of Link Test..............................................................................................................................61Results of RF Scan Test .......................................................................................................................61Retrieving Site Survey Results.............................................................................................................61Appendix B: PC Tools ............................................................................................................62B.1: Description ..................................................................................................................................................62B.2: Launching PC Tools....................................................................................................................................62B.2.1: Creating Jobsite.................................................................................................................................63B.2.2: Opening Jobsite.................................................................................................................................64Appendix C: Troubleshooting and Testing .......................................................................... 66C.1: Troubleshooting ..........................................................................................................................................66C.2: Testing FWSG and Devices ........................................................................................................................66C.2.1: Testing LED Indications...................................................................................................................66C.3: Testing Wireless Network ...........................................................................................................................66C.3.1: Network Topology............................................................................................................................67Parent-Child Devices............................................................................................................................67Orphan Devices ....................................................................................................................................67Class A Compliance .............................................................................................................................67C.3.2: History Events...................................................................................................................................68C.3.3: Network Snapshots ...........................................................................................................................68C.3.4: Network Statistics .............................................................................................................................68C.3.5: Device Attributes ..............................................................................................................................68Index......................................................................................................................................... 69
8 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013About This Guide PurposeSection 1: About This Guide1.1 PurposeThe Notifier Wireless Sensor Network user’s manual provides an overview of the following:• Wireless fire alarm system.• Instructions for installing and configuring the wireless devices.• Information on monitoring the status of the wireless devices.• Removal and replacement procedures of the FWSG.• Testing, maintenance, and firmware upgrade information of the FWSG.1.2 Assumed KnowledgeThe document is created with the assumption that all users are familiar with working on a PC andlaptop for configuration purposes. Installers should be familiar with Fire Alarm and Related Ser-vice Standards. The terminology and level of details of this document reflect this assumption.1.3 Site SurveyA site survey is recommended to assess and qualify the site prior to installing the Wireless Fire Alarm system. The site survey utility allows you to perform the Link quality test and radio fre-quency (RF) assessment of the site. This information is used for site qualification, maximum device spacing identification, and configuring the network. This helps to optimize the reliability and per-formance of the wireless network in the wireless fire alarm system. Conduct a site survey, and ensure there are no obstructions for using RF communications. For more information on a site sur-vey, refer to Appendix A:, "Site Survey".
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 9Abbreviations and Meanings About This Guide1.4 Abbreviations and MeaningsThe following table lists the abbreviations and their definitions used in this manual.Abbreviation DefinitionAHJ Authority Having JurisdictionANSI American National Standards InstitutedBm Milli DecibelFACP Fire Alarm control PanelFCC Federal Communications CommissionFWSG Fire Wireless System GatewayISM Band Industrial, Scientific and Medical Radio Bands.LCD Liquid Crystal DisplayLED Light Emitting DiodemA MilliampereMHz MegahertzNFPA National Fire Protection AssociationPC Personal ComputerRF Radio FrequencySLC Signaling Line CircuitUI User InterfaceUL Underwriters LaboratoriesUSB Universal Serial Bus
10 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013FWSG DescriptionSection 2: FWSG2.1 Description The FWSG is a device in a wireless fire system th at acts as a bridge between fire alarm controlpanels and wireless fire devices. All wireless fire devices communicate with the FWSG over thewireless network formed by the devices and the FWSG.The FWSG is powered by either the SLC loop or from any external 24VDC UL listed power sup-ply. It uses FlashScan protocol on the SLC to communicate with the panel and a proprietary wire-less protocol to communicate with wireless fire devices. The following graphic is an illustration ofthe components of the Firelite Wireless Sensor Network.Figure 2.1 Wireless Fire Alarm System 2.2 Agency Approvals2.2.1 FCCThis device complies with part 15 of the FCC Rules. Operation is subject to the following two con-ditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interferences that may cause undesired operation.FCC ID PV3WFSGWWARNING: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 11Specifications FWSG2.3 SpecificationsFollowing are the specifications of an FWSG.NOTE: Devices that do not meet the minimum signal strength or have an ambient noise level that exceeds the limit are not allowed to join the mesh network.2.3.1 Environmental Specification2.4 Installing FWSG2.4.1 Before InstallingChoose a location for the FWSG that is clean, dry, and vibration-free. The area should be readily accessible with sufficient room to easily install and maintain the FWSG. Metal obstructions that impede the radio frequency communication and should be avoided. Carefully unpack the system and inspect for shipping damage if any. All wiring must comply with the national and local codes for fire alarm systems.Specifications DataExternal Supply Electrical Ratings 18V-30VSLC Electrical Ratings 15V-30VMaximum current when using the external supply 40mAMaximum current when using the SLC power supply 24mAMaximum SLC Resistance 50 OhmsMinimum signal strength level needed at the receiver for a primary path with weak link trouble reporting enabled.-50dBmMinimum signal strength level needed at the receiver for a secondary path or primary path with weak link trouble reporting disabled.Must be 15 dBm higher than the noise floor down to a minimum of -87dBm*Maximum ambient noise level -90dBmMaximum RF Power Output +17dBm (Tx power level without antenna)Radio Frequency Lower ISM Band (915 MHz).System Operating Temperature Storage Temperature HumidityFWSG 0°C-49°C/32°F-120°F -10°C-60°C/14°F-140°F 10 to 93% RH Non condensing
12 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013FWSG Mounting & Wiring2.5 Mounting & Wiring2.5.1 MountingThe FWSG has two major pieces, the cover and the mounting plate. The mounting plate is mounted to the wall or ceiling and field wiring is connected to it. The cover contains the PC board and is fas-tened to the mounting plate once the wiring is connected. Mount the mounting plate directly to an electrical box on the ceiling or wall. The plate mounts directly to 4˝ square (with and without plaster ring), 4˝ octagon, 3 1/2˝octagon, single gang or dou-ble gang junction boxes. If an electrical box is not available, the mounting plate can be mounted to any flat surface and the wiring can be connected via the knockout points in the mounting plate. To mount the FWSG, do the following:1. Pull the wiring through the opening in the mounting plate.2. Mount the mounting plate to the junction box, wall or ceiling. See Figure 2.2, “Mounting Plate”.3. Connect field wiring to the terminals, as described in 2.5.2 "Wiring".4. Connect necessary jumpers where applicable, as described in 2.5.3 "FWSG Powered from SLC".5. To mount the cover, align the locating pins on the cover to the corresponding slots in the mounting plate. See Figure 2.3, “Cover Attaching to Mounting Plate”.6. Secure the cover by tightening the mounting screws. Figure 2.2 Mounting Plate
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 13Mounting & Wiring FWSGFigure 2.3 Cover Attaching to Mounting Plate
14 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013FWSG Mounting & Wiring2.5.2 Wiring• All wiring must be installed in compliance with the National Electrical Code and the local codes having jurisdiction.• 12-18 AWG is recommended. Figure 2.4 Wiring Diagram with Terminal DescriptionsFor wiring connections, follow this procedure:• Strip about 3/8” of insulation from the end of the wire. • Then, to make the wire connection, slide the bare end of the wire under the appropriate clamping plate, and tighten the clamping plate screw. NOTE: Do not loop the wire under the clamping plate.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 15Mounting & Wiring FWSG2.5.3 FWSG Powered from SLCTo power the FWSG using the signal line circuit, connect it as described in table 2.1 below:Figure 2.5 Wiring Connections (FWSG powered from SLC)NOTE: It is recommended to use the same wire gauge if there are multiple connections to the same terminal.The FWSG provides isolation of short circuits on the SLC in Class A installations, that use the A6 and A7 connections as an in and out connection. A5 is common for SLC wiring that enters and leaves. Class B wiring that terminates at the FWSG can use either the A6 or A7 connection for the SLC positive. SLC connections are power limited by the panel. An interruption in the SLC that causes a loss of power at the FWSG for more than 100ms may result in a trouble condition and loss of fire protection provided by the wireless devices for up to 15 minutes. Using an external 24V power source (not SLC power) is recommended for installations that require fire protection in the presence of short circuits, including class A applications and applications that utilize isolator mod-ules.Terminal Pins Description A5 & A7 SLC Common & SLC Output/InputA5 & A6 SLC Common & SLC Input/OutputA4 & A5 Jumper selection to enable power from the SLC supply (Insert jumper when using SLC power)A3 UnusedA1 & A2 Jumper selection to disable power from the external supply. (Insert jumper when using SLC power) Table 2.1
16 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013FWSG Mounting & Wiring2.5.4 FWSG Powered from an External +24VDC SourceTo power the FWSG using a +24VDC source, connect the FWSG as described in table 2.2 below. Figure 2.6 Wiring Connections -FWSG powered from an external +24VDC sourceNOTE: Terminal A5 is referenced more than once in the above connections. It is recommended to use wire of the same gauge for all connections to A5 and use the same wire gauge if there are multiple connections to the same terminal.The FWSG provides isolation of short circuits of the SLC in class A installations that use the A6and A7 as an in and out connection. A5 is common for in and out SLC wiring. Class B SLC wir-ing that terminates at the FWSG can use either the A6 or A7 connection for the SLC positive. SLC connections are power limited by the panel. 24VDC must be power limited by the source.Terminal Pins Devices PoweredA5 & A7 SLC Input/outputA5 & A6 SLC Input/outputA4 UnusedA2 & A3 +24VDC input. Voltage range from 18VDC to 30VDC. Use only power limited circuitsA1 UnusedTable 2.2
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 17Configuration and Programming FWSG2.6 Configuration and ProgrammingThe goal of configuring and/or programming the FWSG is to: 1. Create a profile - A profile is a set of parameters that binds together the FWSG and the devices in a mesh network. 2. Distribute the profile to every device that will be a part of the mesh.3. Form the mesh - The mesh cannot be formed until the profile is assigned to the FWSG. The profile contains a mesh ID and, if required, a password, that are used when forming the associations. Creating and distributing the profile will enable all the devices that have that profile to form associative links when the mesh is formed. All devices, including the FWSG, require a common profile.This section shows how to configure/program an FWSG with a profile, how to distribute that pro-file to other devices, and how to form all these devices into a mesh. These processes may be per-formed with or without using PC-based configuration tool.2.6.1 Without a PC-based Configuration ToolThis section shows the configuration of the FWSG using only a magnet and a screw driver. For configuration instructions using the PC-based configuration tool, refer to 2.6.2 "With a PC-based Configuration Tool".There are two ways to provide an FWSG with a profile without using a configuration tool.• Create a new profile using the FWSG• Assign a previously created profile to the FWSG using a distributor.Create a New ProfileTo create a unique profile in the FWSG without using the PC-based configuration tool, perform the following steps.1. Start with the device powered off. The process is performed during the start-up.2. Power on the FWSG using SLC power or external +24V. This can be done either by attaching the FWSG to its mounting plate with the terminals already energized, or by connecting the SLC or external source wiring to a FWSG that is already installed in its mounting plate.3. Verify if the FWSG is in the factory default state; if it is in the factory default state, both the LEDs on the FWSG flash red (double blink) every second for ten seconds. If the LEDs are yellow, refer to the topic below on "Removing a Profile".Figure 2.7 FWSG with LEDs and Magnetic Sensors
18 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013FWSG Configuration and Programming4. Activate either magnetic sensor with a magnet within ten seconds of starting up the FWSG while the double red blink is active on the FWSG. (If you miss this ten-second window, power down the FWSG and repeat step 1). The LED next to the magnetic sensor emits a red light for one second when it is activated.When the profile is successfully created, the LEDs on the FWSG emit green light for five seconds (Refer to 2.7.2 "Magnet Sensor Activations" for further information on activating magnetic sen-sors). A default profile has been created, containing a mesh ID, and a password. The default pass-word is ‘12345’ and is needed if the FWSG is locked by the FACP and later accessed by the PC-based configuration tool.Next, the FWSG starts the profile distribution mode. Refer to 2.6.3 "Profile Distribution" for fur-ther information on profile distribution mode.Assign a Previously Created Profile Using a DistributorTo assign an existing profile to the FWSG (as you would do during a replacement), use the FWSG that has the profile, or a device in the mesh that contains the profile, to distribute that profile to the FWSG that requires it. Perform the following steps:1. Ensure that the FWSG or other mesh device with the profile is set for distribution (Refer to 2.6.3 "Profile Distribution" or 3.6.2 "Distributor Mode").2. Start with the device powered off. The process is performed during the start-up.3. Power on the FWSG and ensure it is in the factory default state (Refer to steps 1 and 2 in the above topic "Create a New Profile").4. Bring the profile distributor within 20 feet of the FWSG. 5. Wait until the FWSG blinks only a single red blink (ten seconds after startup). 6. Use a magnet to activate either of the magnetic sensors. The LED blinks a single red every half-second indicating that it is searching for a profile.When the profile is successfully received from the distributor, the LEDs on the FWSG emit green light for five seconds. If the profile is rejected, the FWSG LEDs emit red light for five seconds.Removing a ProfileTo remove the profile from an FWSG, perform the following steps:1. Start with the device powered off. The process is performed during the start-up.2. Power on the FWSG using SLC power or external +24V. This can be done either by attaching the FWSG to its mounting plate with the terminals already energized, or by connecting the SLC or external source wiring to a FWSG that is already installed in its mounting plate.3. Verify the FWSG is in the profile modification state; if it is in the profile modification state, both the LEDs on the FWSG flash yellow (double blink) every second for ten seconds.4. Activate both using magnetic sensors within ten seconds of starting up the FWSG (while the double yellow blink is active on the FWSG) or repeat step 1 (If you miss the ten second window, power down the FWSG and repeat steps 1 and 2).The FWSG LEDs blink green every second for five seconds indicating that the profile is removed.Create Mesh NetworkMesh formation forms a wireless communication mesh around the FWSG. The FWSG communi-cates with all devices in range that have a common profile and establishes communication links with all the devices. Once a device joins the mesh, it acts as a repeater for devices out of the range of the FWSG. All devices must be in their final mounting locations prior to initiating the mesh for-mation. The mesh formation is initiated and terminated by the FWSG.To form a mesh network, ensure that the FWSG is powered on and contains a profile (Refer to 2.7.3 "LED Indications" for information on how the FWSG indicates its status). Activate the mesh for-mation magnet sensor on the FWSG with a magnet.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 19Configuration and Programming FWSGFigure 2.8 Mesh Formation Magnetic Sensor on a FWSGThe FWSG transitions to the mesh formation mode and establishes communication with all the devices containing a common profile. The blink pattern on the FWSG indicates that it is in mesh formation mode. •At this stage, both the LEDs on the FWSG blink twice every 3.4 seconds. •The first blink is green and the second blink is red when the FWSG is acting as a profile distributor and forming the mesh. • The first blink is green and the second blink is yellow when the FWSG is only forming the mesh.Mesh formation typically takes one minute for each device in the mesh. Mesh formation automati-cally terminates 10 minutes after the last device joins the mesh. The mesh formation can be termi-nated manually by the user by activating the mesh formation magnetic sensor again. Once the mesh formation is complete, the network transitions to optimize the mesh. For further operating instructions, refer to 2.7 "Operations".2.6.2 With a PC-based Configuration ToolAssigning Profile with PC Tools To assign a profile to the FWSG using the PC Tools application, do the following:1. Connect the W-USB dongle device to your computer. For more information on USB dongle, refer to Section 4: "USB Adapter".2. Launch the PC Tools application. Refer Appendix B: "PC Tools" to know about launching the PC Tools application.3. Go to the Create Mesh Network step.4. Create a new profile or import an existing profile as required.5. Select and open the profile to be assigned to the FWSG from the Name drop-down list in the left panel.6. Power on the FWSG in range of the PC Tools.
20 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013FWSG Configuration and Programming7. Select the FWSG from the Communicator panel.8. Click Assign.The FWSG is now included in the list of devices with a profile assigned.Removing Profile with PC ToolsTo remove a profile in a FWSG using the PC Tools application, do the following:1. Connect the W-USB dongle device to your computer. For more information on the USB dongle, refer to Section 4: "USB Adapter".2. Launch the PC Tools application. Refer Appendix B: "PC Tools" to know about launching the PC Tools application.3. Go to the Site Survey, Create Mesh Network, or Diagnostics step.4. Click Extras and select Reset Devices. The Reset Devices screen appears, displaying the FWSG and other devices that have a profile assigned.5. Click to select the FWSG and click Reset Device to remove the profile.The profile is removed and the FWSG is reset to factory default state.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 21Configuration and Programming FWSGMesh Formation with PC ToolsTo create a mesh network using the PC Tools, perform the following steps.1. Connect the W-USB dongle device to your computer. For more information on the USB dongle, refer to Section 4: "USB Adapter"2. Launch the PC tools application. Refer Appendix B: "PC Tools" to know about launching the PC Tools application.3. Go to the Create Mesh Network step.4. Navigate to the second step of Create Mesh Network by clicking on top of the screen.5. Click to select the FWSG displayed in the Gateways in Range table, and click 'Start Mesh Formation'.When the mesh is formed, the tool helps you to track the number of devices that have joined the mesh, and view the progress. The mesh formation terminates in 10 minutes after the last device joins the mesh. In addition, it can be terminated by the user by clicking Stop Mesh Formation.Once mesh formation is complete, the network transitions to optimize the mesh. For further operat-ing instructions, refer to 2.7 "Operations".2.6.3 Profile DistributionThere are two ways to initiate profile distribution from an FWSG. • Automatically after creating a profile, • Activating the profile creating magnetic sensor when it has a profile. After Creating a Profile Profile distribution is automatically enabled from an FWSG after creating a profile. The profile distribution automatically terminates after 10 minutes. Activating the Profile Magnetic Sensor when it has a Profile Activating the profile magnetic sensor while it has a profile will put an FWSG in a mode of distributing the profile to any device that requests a profile. The FWSG’s LED pattern will be altered when it is distributing a pro-file for easy identification. Profile distribu-tion will automatically terminate after 10 minutes. For more information on FWSG LED patterns, refer to the table in 2.7.3 "LED Indications". Figure 2.9 Profile Magnetic Sensor on FWSG
22 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013FWSG Operations2.6.4 SLC ConfigurationThe FWSG,• Communicates with the control panel via the SLC circuit. • Is a FlashScan only device. • CLIP mode is not supported. • Is only compatible with Fire Alarm Control Panels version 21 or higher.• Occupies one module SLC address. Set the address using the rotary dials on the FWSG prior to installation. The point uses the following configuration parameters:• Module Type: Monitor• Type Code Label: RF GATEWAY• Flash Scan Type: RF GATEWAYAn FWSG does not initiate alarms but the point is used for event reporting.2.7 Operations2.7.1 FWSG Modes Of OperationFigure 2.10 FWSG Modes Of OperationStart UpStartup is a temporary mode of operation. It is during the startup mode, a profile can be created or removed. The startup period lasts for 10 seconds. If a particular unit contains a profile, the LEDs blink yellow twice every second. If the unit does not contain a profile, the LEDs blink red twice every second. During startup, the FWSG does not provide fire protection.After startup, the FWSG proceeds to the factory default state if a profile was removed or missing. In the presence of a profile, the FWSG will proceed to mesh formation if it was previously part of a mesh network or normal mode if it was not previously part of a mesh network. The FWSG does not respond to the FACP during startup mode.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 23Operations FWSGFactory DefaultFactory default is the initial mode of the FWSG. The FWSG and peripheral devices do not provide any fire protection when they are in factory default mode. The FWSG does not communicate with wireless devices. The only wireless communication is with the configuration tool. The configura-tion tool needs to be within 20 feet of the FWSG for communication. The FWSG needs to be assigned a profile before continuing the installation. The FWSG reports a ‘PROFILE MISSING' or ‘PR MIS’ trouble to the FACP. The FWSG reports “Factory Default” to the communicator display of the PC Tools application.Profile ConfiguredThe FWSG enters the profile configured mode after getting assigned a profile from the tool or a distributor or creating a profile. Profile configured mode is a temporary mode before the FWSG transitions to mesh formation or normal mode. The FWSG does not provide fire protection in the profile configured mode. While in the profile configured mode, the FWSG reports a "MESH NOT FORMED" or "NO MSH" trouble to the FACP. The FWSG reports “Profile Assigned” to the communicator display of the PC Tools appli-cation.Mesh FormationThe FWSG must have a profile before entering mesh formation. The FWSG and the peripheral devices do not provide any fire protection in mesh formation. The FWSG automatically enters mesh formation mode in the following ways: • After creating a profile using the mesh formation sensor.• After activating the mesh formation sensor with a magnet when the FWSG contains a profile.• Automatically after startup when the FWSG previously was part of a mesh.• By command from the PC Tools application.• By command from the FACP.A FWSG in mesh formation mode instructs all devices in the mesh to also transition to mesh for-mation. The FWSG and all communicating devices search for new or lost devices with the same profile to join the network.If the FWSG automatically entered mesh formation mode after startup, then mesh formation termi-nates after all existing devices are recovered. If new devices are found or if mesh formation was initiated by the user, then mesh formation terminates after a period of 10 minutes without any new devices joining the mesh. At any point, mesh formation can be terminated by user interaction by activating the magnet sensor again, by using the PC Tools application, or by using FACP.The FWSG reports a “NO WIRELESS DEVS” or “NO DEV” trouble when it is in Mesh Formation mode without any attached devices. The FWSG reports a “MESH IS FORMING” or “MS FRM” trouble when it is mesh formation mode with additional devices in the mesh. The FWSG reports “Mesh Formation” to the communicator display of the PC Tools application.Initial Mesh OptimizationThe initial mesh optimization mode automatically runs after each mesh formation. The FWSG and peripheral devices do not provide fire protection during the initial mesh optimization. Mesh opti-mization mode analyzes the signal strengths between devices. The FWSG designates the primary and secondary communication paths between devices that provide a redundant path for all trans-missions. Mesh optimization terminates automatically once all devices have a redundant communi-cation path and signal strengths that meet the requirements of primary and secondary transmission paths. Any device that does not have a redundant path or meet the requirements for signal strength will report a fault.
24 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013FWSG OperationsThe FWSG reports an ‘OPTIMIZING MESH’ or ‘OPT MS’ trouble to the FACP. The FWSG reports “Optimization” to the communicator display of the PC Tools application.Normal ModeNormal mode can be described as a standard operating state. The mesh network is formed, provid-ing fire protection. The mesh network continuously searches for additional devices with a match-ing profile to join the mesh. To avoid interference, the mesh network periodically checks for adjacent mesh networks created by Honeywell. The FWSG reports “Normal” to the communicator display of the PC Tools application.Rescue ModeDuring normal mode, when a device loses communication to the network, the FWSG triggers the rescue mode in all communicating devices. All devices in communication continue to provide fire protection during rescue mode; but also search for a lost or added device. The rescue mode termi-nates automatically 6 minutes after the last device is rescued and returns to the normal mode. The FWSG does not report trouble during rescue mode. The FWSG reports “Rescue” to the communi-cator display of the PC Tools application.Mesh OptimizationIn addition to the initial mesh optimization, the routine executes after any large change to the net-work configuration or to recover from a link failure (class A fault). Mesh optimization that occurs during the normal mode does not generate a trouble and provides fire protection from all devices that are participating in the mesh communication. The FWSG reports “Optimization” to the com-municator display of the PC Tools application.BootloaderThe FWSG enters the bootloader mode when it is being updated using the PC Tools application. The FWSG does not communicate with the FACP during bootloader mode. The FWSG reports “Bootloader” to the communicator display of the PC Tools application.2.7.2 Magnet Sensor ActivationsProfile Magnetic SensorThe profile magnetic sensor (Figure 2.9, “Profile Magnetic Sensor on FWSG”) is used to create a unique profile on startup. It can also be used to start profile distribution for a FWSG that contains a profile. The LED next to the profile magnetic sensor emits solid red light for ½ a second when the sensor is activated.Mesh Formation Magnetic SensorThe mesh formation magnetic sensor (Figure 2.8, “Mesh Formation Magnetic Sensor on a FWSG”) toggles the FWSG, in and out of mesh formation mode. The initial activation of the sensor puts the FWSG in mesh formation mode (as long as it contains a profile). A subsequent activation of the magnetic sensor toggles the FWSG out of mesh formation and into the initial mesh optimization and normal mode. The FWSG can be placed back into mesh formation by activating the magnet sensor once again. The Mesh formation magnetic sensor can also be used to create a profile on startup for a FWSG that does not already contain a profile.The LED next to the mesh formation magnetic sensor emits solid red light for ½ a second when the sensor is activated. 2.7.3 LED IndicationsThe two LEDs on the FWSG blink in the same pattern to allow the LED to be viewed from any angle. The LED indications are provided in the table below.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 25Operations FWSGDuration of LED stateAll units are in seconds. Minute is indicated by M.Example:LegendLED colorNo. of blinksInterval between blink patternsApproximate durationWill transition to next state after 30 min (approx)First blink is green. Second is yellowTwo blinks in this pattern7 sec between blink patterns7M30Condition Action RequiredDevice is ready to updateLED PatternProle removed Gateway has returned to the factory default stateMesh formation Gateway is forming the mesh & looking for devices that are not in the meshWait until all devices join the mesh, and then terminate mesh forma-tionUse PC based congura-tion tool to initiate the downloadMesh formation with prole distributionGateway is forming the mesh & looking for devices that are not in the mesh. The gateway is also distributing a prole to any device that requests a proleWait until all devices join the mesh, and then terminate mesh forma-tionApp eraseApp loadingNew application code is being downloaded77251414Normal Mode / Background mesh optimiza-tionNormal operation of the gatewayNormal Mode/Back-ground mesh optimization with prole distributionNormal operation of the gateway. The gateway is also distributing a prole to any device that requests a proleProle accepted Gateway is now prole assigned5Rescue Mode Gateway and the mesh network are searching for any device that is not in the mesh network with the same prole76MBootloader5
26 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013FWSG OperationsDuration of LED stateAll units are in seconds. Minute is indicated by M.Example:LegendLED colorNo. of blinksInterval between blink patternsApproximate durationWill transition to next state after 30 min (approx)First blink is green. Second is yellowTwo blinks in this pattern7 sec between blink patterns7M307Rescue Mode with prole distributionGateway and the mesh network are searching for any device that is not in the mesh network with the same prole. The gateway is also distributing a prole to any device that requests a proleProle assigned; pending hall sensor activationsstarting up with a prole Activate both hall sensors simultaneously within 10 seconds to remove a prole1st mesh optimizationMesh is formed and initializingEnsure all devices in the mesh have a valid address.710 16M15MCondition Action RequiredLED Pattern741414Refer to the panel to identify the trouble and possible resolution1st mesh optimization with prole distribu-tionMesh is formed and initializing. The gateway is also distributing a prole to any device that requests a proleGeneric Trouble The gateway has a trouble condition.Refer to the panel to identify the trouble and possible resolutionGeneric Trouble with prole distributionThe gateway has a trouble condition. The gateway is also distribut-ing a prole to any device that requests a prole.Ensure all devices in the mesh have a valid address.Address Trouble The gateway is in a dual address condition with another wireless module in the mesh or there is a device in the mesh set to address 0.15M
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 27Operations FWSGDuration of LED stateAll units are in seconds. Minute is indicated by M.Example:LegendLED colorNo. of blinksInterval between blink patternsApproximate durationWill transition to next state after 30 min (approx)First blink is green. Second is yellowTwo blinks in this pattern7 sec between blink patterns7M304Ensure all devices in the mesh have a valid address.Address Trouble with prole distributionThe gateway is in a dual address condition with another wireless module in the mesh or there is a device in the mesh set to address 0. The gateway is also distributing a prole to any device that requests a prole.Condition Action RequiredLED PatternFactory default; pending hall sensor activationStarting up without a proleActivate either hall sensors within 10 seconds to create a default prole Waiting for proleGateway is factory default Use PC tool to assign prole or activate switch to search for proleSearching for proleGateway is factory default and requesting a prole from a distributor or another gatewayProle rejected; incompatible deviceThere is a mismatch between the prole and the gateway. Recreate the prole or update the gatewayCreate prole Gateway is creating a default prole15110100.51M
28 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013FWSG Operations2.7.4 Lock/Unlock FWSGThe FWSG can be locked to prevent access to the magnetic sensors, and to password-protect all wireless interactions. The lock function can be performed by the PC Tool or by the FACP. When the PC Tool is used to lock the FWSG, a password must be provided for all future interactions, including unlocking the FWSG. When the FWSG is locked by the FACP for the first time, a default password of "12345" is applied. If the FWSG was previously locked with a password from the PC tools, the previous password will be applied. Use this password for all future interactions from the PC Tools application.Lock/Unlock FWSG through FACPThe lock/unlock function for the NFS2-3030 is accessible using the point programming menu. For more information refer to the NFS2-3030 manual, part number LS10006-051NF-E.Lock/Unlock FWSG through PC toolsTo lock/unlock FWSG through PC tools, perform the following steps:1. Connect the W-USB dongle device to your computer. For more information on USB dongle, refer to Section 4: "USB Adapter".2. Launch the PC Tools application. Refer to Appendix B: "PC Tools" to know about launching the PC Tools application.3. Go to Site Survey, Create Mesh Network, or Diagnostics step.4. Click Extras. The following screen is displayed. 5. Select Lock/Unlock Gateway. The Lock/Unlock gateway screen appears, displaying the FWSG that is locked.6. To lock or unlock the gateway, click Lock or Unlock as required.•Lock - The Lock Gateway screen is displayed. Create a password and click Lock. The gateway is locked.•Unlock - The Enter password for Gateway screen is displayed. Enter the password and click Unlock. The FWSG is unlocked.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 29Operations FWSGPassword ResetTo reset the password, contact technical support.2.7.5 Weak Link Trouble ReportingThe Notifier Wireless Sensor Network uses two paths of communication for each device. To estab-lish the link between devices as a viable communication path, the signal strengths must meet the limits provided in Section 2.3, “Specifications”. The Wireless Sensor Network implements a higher threshold for primary connections to provide an extra layer of robustness and immunity from interference. A weak link trouble condition is initiated for any device that does not have at least one connection at the primary threshold. This is an optional setting that can be disabled to ignore the weak link trouble condition. The trouble can be disabled at the FWSG or at the FACP (NFS2-3030 only). Disabling the trouble reporting at the panel will prevent the event from regis-tering as a trouble but still enters into history as a background event. Disabling the trouble report-ing at the FWSG prevents the event from being reported to the FACP as a trouble or a non-trouble event. To have trouble reporting enabled, turn the settings on at both locations.Disabling Trouble Reporting at the FWSG Using PC ToolsTo disable trouble reporting at the FWSG through PC tools, perform the following steps:1. Connect the W-USB dongle device to your computer. For more information on USB dongle, refer to Section 4: "USB Adapter".2. Launch the PC Tools application. Refer to Appendix B: "PC Tools" to know about launching the PC Tools application.3. Go to Diagnostics step.4. Choose the FWSG from the communicator pane.5. Click View Mesh.6. Click Advanced Functions. A drop-down list is displayed.
30 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013FWSG Operations7. Click Weak links troubles. The Report weak links troubles screen is displayed.8. Click Turn off reporting. The trouble reporting is disabled.Disabling Trouble Reporting in the PanelTo disable trouble reporting at the panel, refer to the manual for the NFS2-3030, part number LS10006-051NF-E.2.7.6 Collapse Network CommandThe collapse command is a diagnostic function to break the mesh network. All devices will retain the profile information but will be removed from the mesh. The mesh can be immediately reformed by activating mesh formation. CAUTION: FIRE PROTECTION FROM WIRELESS DEVICES WILL BE LOST WHEN A COLLAPSE COMMAND IS ISSUED.The mesh network can be collapsed using the PC-based configuration tool or through the NFS2-3030 panel. Collapsing Mesh Network Using PC ToolsTo collapse the mesh network using the PC based configuration tool, perform the following steps:1. Connect the W-USB dongle device to your computer. For more information on USB dongle, refer to Section 4: "USB Adapter".2. Launch the PC Tools application. Refer to Appendix B: "PC Tools" to know about launching the PC Tools application.3. Go to Diagnostics step.4. Select a Gateway from the Communicator pane.5. Click View Mesh. The mesh is displayed.6. Click Advanced Functions on top of the mesh display. A drop-down list is displayed.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 31Operations FWSG7. Click Collapse Mesh. The Collapse mesh network screen is displayed.8. Click Ye s. The network is collapsed and a confirmation is displayed as shown below:Collapsing Mesh Network in the PanelTo collapse the mesh network using the NFS2-3030, refer to the "shutdown wireless" entry in the NFS2-3030 operations manual, part number LS10006-051NF-E.2.7.7 Silence Network CommandThe silence network command is a diagnostic function to turn off all radio communication from the wireless devices for the set amount of time. All devices will retain the profile information but will be removed from the mesh. The devices will not send or receive any wireless communication until the set time expires or the device is rebooted. The mesh network can be reformed at the end of the silence period or after the device is restarted. CAUTION: FIRE PROTECTION FROM WIRELESS DEVICES WILL BE LOST WHEN A SILENCE COMMAND IS ISSUED.The mesh network can be silenced using the PC-based configuration tool or through the NFS2-3030 panel.Silencing Mesh Network Using PC ToolsTo silence the mesh network using the PC-based configuration tool, perform the following steps:1. Connect the W-USB dongle device to your computer. For more information on USB dongle, refer to Section 4: "USB Adapter".2. Launch the PC Tools application. Refer to Appendix B: "PC Tools" to know about launching the PC Tools application.3. Go to Diagnostics step.4. Select a Gateway from the Communicator pane.5. Click View Mesh. The mesh is displayed.
32 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013FWSG Operations6. Click Advanced Functions on top of the mesh display. A drop-down list is displayed.7. Click Silence Devices. The Silence mesh network screen is displayed.8. Select the time interval to silence the wireless devices from the dropdown list and click Ye s .9. Enter the Verfication Password in the Gateway Password screen.The network is silenced and a confirmation is displayed as shown below:Silencing Mesh Network in the PanelTo silence the mesh network using the NFS2-3030, refer to the "shutdown wireless" entry in the NFS2-3030 operations manual, part number LS10006-051NF-E.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 33Operations FWSG2.7.8 Multiple Wireless Sensor Network Installation RestrictionsNotifier’s Wireless Sensor Network technology shares the RF spectrum with other Honeywell Wireless Sensor Network systems. Honeywell has established a limit of 4 overlapping networks to avoid congestion in the RF spectrum. If the limit of overlapping systems is exceeded, a system trouble will be generated for the system that detects 4 or more adjacent networks. To resolve this situation, the instances of overlap need to be removed. Refer to Appendix C: "Troubleshooting and Testing" for suggestions on removing overlap between wireless networks. The trouble will be self restoring up to 36 hours after the condition is resolved. To expedite the trouble resolution, toggle the network that is reporting the trouble in and out of mesh formation mode. 2.7.9 Avoiding RF InterferenceThe Notifier wireless mesh network uses radio frequency hopping spread spectrum technology to communicate in the 900 MHz ISM band (902MHz to 928MHz). Other commercial and industrial products also operate in this band. If two-way radios or other wireless communication devices are used during the installation process it is recommended that they be kept at least 4 feet away from the Notifier wireless devices or that they operate on a different frequency band to ensure rapid mesh formation. A properly installed Notifier wireless mesh network with primary link reporting enabled will be highly immune to RF interference from other wireless products even when they are nearby. The use of the primary link reporting feature is highly recommended. If the system is installed in a con-trolled environment where other 900 MHz ISM band devices will not be present, the primary link reporting feature may be disabled to permit greater distances between installed devices if required. The Notifier wireless mesh network will be able to automatically detect and avoid certain types of in-band channel interference (often caused by two-way radios) by using an alternate channel set. The system will log detection and avoidance of this kind interference in the FWSG history as "Walkie Talkie Mode" Entry or Exit and in the NFS2-3030 history as Alternate Channel Set or Nor-mal Channel Set.
34 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013FWSG Operations2.7.10 Trouble StatesNFS2-3030NCA-2OnyxworksNFS2-640NFS-320 Description Course of ActionRADIO JAMMINGJAM Non-latchingThe FWSG is being overloaded with RF energy and is unable to receive messages from other devices. Identify any RF emitters in close proximity of the FWSG and remove them, or relocate the FWSG.INCOMPATSOFTIN SFT Non-latchingSoftware mismatch between the application code for the RF processor and the SLC processor.Use PC Tools to identify the mismatch, and update the processors as necessary for compatibility.MESH IS FORMINGMS FRM Non-latchingThe FWSG and attached devices are searching for additional devices to join the mesh. The wireless system is not able to provide fire protection during this time.Wait until all desired wireless devices are communicating and members of the mesh network. Once all desired devices are in the mesh network, the mesh forming mode can be terminated by the user by activating the Mesh formation magnetic sensor or by using the PC Tools. If no action is taken, this mode will automatically exit 10 minutes after the last device joins.MESH NOT FORMEDNO MESH Non-latchingThe FWSG contains a profile but has not formed a mesh.To form a mesh, refer to "Create Mesh Network".OPTIMIZING MESHOPT MS Non-latchingThe FWSG is performing the initial identification and assignment of optimal communication paths for the mesh network. The wireless system is not able to provide fire protection during this time.No action needed. The duration of this event correlates to the number of devices in the mesh. A fully loaded mesh may take up to 5 minutes to optimize.PROFILE MISSINGPR MIS Non-latchingThe FWSG is in the factory default state and is not providing fire protection.A profile needs to be created or assigned to the FWSG before a mesh can be formed.NOWIRELESS DEVSNO DEV Non-latchingThe FWSG is functional, but is not in communication with any wireless devices.Verify the desired wireless devices are in range, have matching profiles assigned, have batteries, and are not in the tampered condition. Initiate "Mesh Formation mode" to actively search for devices.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 35Operations FWSGADDRESSFAULTAD FLT Non-latchingThere is either a device in the mesh set to address 0, or there is a duplicate address used for another wireless module at the address of the FWSG.The offending device (detector or module set at address 0 or module at the same address as the FWSG) will be indicating the LED pattern for address fault. Find and resolve that device.MAX GATEWAYSMAX GW Non-latchingWireless communication reliability is compromised due to the installation limits of Honeywell wireless systems being exceeded.Investigate for overlapping or adjacent wireless systems produced by Honeywell. Reduce the instances of overlap by removing systems, or devices in the overlapping region. Refer to 2.7.8 "Multiple Wireless Sensor Network Installation Restrictions" on the installation limits for the Honeywell wireless system. RF DEV NO ANSWERRF DEV Latching trouble; remains active for the first 180 seconds before it can be cleared with a system reset.A wireless device that was part of the mesh has dropped from the mesh.Initiate a system reset at the FACP at least 3 minutes after the trouble was initiated to clear.If the device was intentionally removed, no further action is needed.If the device was not intentionally removed; refer to panel history or active panel troubles to investigate the cause of the disturbance.NFS2-3030NCA-2OnyxworksNFS2-640NFS-320 Description Course of Action
36 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013FWSG Operations2.7.11 History EventsFWSG History EntriesNFS2-3030 DescriptionPR The profile has been received; assigned from either the PC Tools or a distributor device.PC The profile has been created.B The system is currently operating in the alternate channel set due to the presences of an interference source such as a walkie-talkie.SLOT REALIGNMENT (TEMP CHAN SET)The slot assignments are being re-assigned to avoid empty slots; the system is currently operating in the alternate channel set due to the presences of an interference source such as a walkie-talkie.SLOT REALIGNMENT The slot assignments are being re-assigned to avoid empty slots.OPTIMIZING MESH (TEMP CHAN SET)The FWSG is performing a routine identification and assignment of optimal communication paths for the mesh network. The system is currently operating in the alternate channel set due to the presences of an interference source such as a walkie-talkie.OPTIMIZING MESH The FWSG is performing a routine identification and assignment of optimal communication paths for the mesh network. RESCUE MODE (TEMP CHAN SET)A device has been removed or dropped from the mesh. The mesh network is currently scanning for the return of the device or others with a matching profile. The system is currently operating in the alternate channel set due to the presences of an interference source such as a walkie-talkie.RESCUE MODE A device has been removed or dropped from the mesh. The mesh network is currently scanning for the return of the device or others with a matching profile. TEMP CHANNEL SET The system is currently operating in the alternate channel set due to the presence of an interference source such as a walkie-talkie.NORMAL CHANNEL SET The system is normal.PROFILE DISTRIBUTION DISABLEDThe FWSG has terminated the distribution of its profile.PROFILE DISTRIBUTION ENABLEDThe FWSG has started the distribution of its profile.SWITCH ACCESS ENABLEDThe FWSG is unlocked and the magnetic sensors on the front of the FWSG are enabled.SWITCH ACCESS DISABLEDThe FWSG is locked and the magnetic sensors on the front of the FWSG are disabled. Attempts to active the sensors will not be recognized.MAXIMUM DEVICE COUNT EXCEEDEDMore than 50 devices are attempting to join the mesh network. This is beyond the capacity of the mesh network.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 37Operations FWSG
38 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013Devices DescriptionSection 3: Devices3.1 DescriptionSubsystem OverviewThe Wireless Sensor Network consists of the following devices:FWD-200P- Wireless Photoelectric Smoke Detector (FCC ID AUBWFSSD)The wireless photoelectric smoke detector is powered by four CR123A batteries. It has a sensor head to detect smoke and LEDs to indicate the activation & trouble status. For further details, refer to the table in 3.7.2, "LED Indications".FWD-200ACCLIMATE- Wireless Acclimate (FCC ID AUBWFSSD)The wireless acclimate is powered by four CR123A batteries. It has a sensor head to detect smoke and LEDs to indicate activation & trouble status. For further details, refer to the table in 3.7.2, "LED Indications".FWH-200ROR135- Wireless Rate of Rise Heat Detector (FCC ID AUBWFSSD)The rate of rise heat detectors are powered by four CR123A batteries. The detectors have LEDs, to indicate the activation & trouble status. For further details, refer to the table in 3.7.2, "LED Indica-tions".FWH-200FIX135- Wireless Fixed Heat Detector (FCC ID AUBWFSSD)The fixed heat detectors are powered by four CR123A batteries. The detectors have LEDs, to indi-cate the activation & trouble status. For further details, refer to the table in 3.7.2, "LED Indica-tions". FW-MM- Wireless Monitor Module (FCC ID AUBWFSMM) The wireless monitor module is powered by four CR123A batteries. It can be connected to a switch within three feet of its location or wired directly to the pull station. The module has LEDs, to indi-cate the activation & trouble status. For further details, refer to table in 3.7.2, "LED Indications".3.2 Agency Approvals3.2.1 FCCThis device complies with part 15 of the FCC Rules. Operation is subject to the following two con-ditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interferences that may cause undesired operation.WARNING: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 39Specifications Devices3.3 SpecificationsFollowing are the specifications for the devices.Table 3.1 Device SpecificationsThe below table provides details on the device references.3.4 Installing DevicesFor information on installing the devices, refer to the manuals mentioned in the above table.3.5 Mounting & WiringFor information on mounting and wiring, refer to the manuals mentioned in the table 3.2.3.6 Configuration and ProgrammingThe configuration of a device starts with assigning a profile. Refer to the instructions below for assigning a profile. • Assign profiles using PC Tools.• Assigning profile to a detector with an FWSG or distributor.• Assigning profile to a module with an FWSG or distributor.Specifications DataRadio Frequency Lower ISM Band (915 MHz)Maximum power output +17dBmMinimum signal strength level needed at the receiver for a primary path with weak link trouble reporting enabled.-50dBmMinimum signal strength level needed at the receiver for a secondary path or primary path with weak link trouble reporting disabled.Must be 15 dBm higher than the noise floor down to -87dBmMaximum ambient noise level -90dBmMinimum battery life 1 yearModel Description ManualFWD-200P Photo FWD-200Pand FWD-200ACCLIMATE Intelligent wireless Photoelectric Smoke Sensors. Manual part number for the above devices - I56-4065-000.FWD-200ACCLIMATE AcclimateFWH-200ROR135 Wireless Rate of Rise Heat Rate of Rise Heat FWH-200ROR135 and FWH-200FIX135 Intelligent Wireless Temperature Sensors.Manual part number for the above devices - I56-4066-000FWH-200FIX135 Wireless fixed heatFW-MM Wireless monitor module FW-MM Wireless Monitor Module.Manual part number - I56-4067-000Table 3.2 Device References
40 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013Devices Configuration and Programming3.6.1 Assigning Profiles NOTE: To assign a profile, the device must be in a factory default state. A single red light flashes on the LED confirming that the device is in the default state. To restore the device to factory default state, refer to 3.6.4, "Restoring a Device to Factory Default".Assigning Profile Using PC ToolsTo assign a profile to the device using the PC Tools application, do the following:1. Connect the W-USB dongle device to your computer. For more information on USB dongle, refer to Section 4:, "USB Adapter".2. Launch the PC Tools application. Refer Appendix B:, "PC Tools" to know about launching the PC Tools application.3. Go to the Create Mesh Network step.4. Create a new profile or import an existing profile as required. 5. Select and open the profile to be assigned to the device from the Name drop down list in the left panel.6. Switch on the device in range of the USB adapter, which is connected to the laptop or PC where PC tool is installed.7. Select the device from the Communicator panel.8. Click Assign.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 41Configuration and Programming DevicesThe device is now included in the list of devices with a profile assigned. When the profile gets assigned, the LEDs emit a solid green light for 10 seconds.Assigning Profile to a Device with an FWSG or DistributorAn FWSG that has a profile can be used to distribute the profile to other devices. The FWSG must be in a state where it can distribute a profile. For more information on converting an FWSG to a distributor, refer to 2.6.3, "Profile Distribution". A device with a profile can be used to distribute the profile. To put a device into distributor mode, refer to the topic, "Converting a Device into a Distributor".Transfer Profile from an FWSG/Distributor to DetectorTo transfer profile from the FWSG/distributor to the detector, do the following:1. Bring the detector within the range of the FWSG. 2. Power on the detector. Ensure the detector is in factory default state. A single or double red light flashing on the detector confirms that the detector is in the default state. 3. To make the detector request the profile on the FWSG, activate the test marker shown in the figure below using a magnet.Figure 3.1 Magnet in a DetectorOnce the magnet sensor is activated, the LED flashes red light every half second indicating that it is requesting a profile. If the profile is successfully received, the LED emits a solid green light for 10 seconds. If the profile is not received within a minute, the LED flashes a red light every ten sec-onds indicating that it has stopped requesting for a profile. Transfer Profile from an FWSG/Distributor to ModuleTo assign a profile to a module, perform the following steps:1. Bring the module in range of the FWSG or the distributor.2. Power on the module. Ensure the module is in factory default state. If the module is in factory default state, the LED blinks red once.3. To make the module request the profile, toggle the state of the tamper condition. To toggle the state tamper condition, start with the faceplate removed.
42 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013Devices Configuration and Programming4. Place the faceplate over the module temporarily, and remove the faceplate again in less than 1 second. Do not attach the mounting screws for the faceplate during this step. The LED flashes red light every half a second indicating that it is requesting a profile. The LEDs blink solid green for ten seconds indicating that the profile is assigned.Figure 3.2 Magnetic Sensor in a Module3.6.2 Distributor ModeConverting a Device into a DistributorNOTE: Only a device with a profile can be made as a distributor.To turn a device into a distributor, do the following: 1. Power up the device with one battery. NOTE: Ensure that the device is in the profile modification mode. This is indicated by a single yellow blink every 5 seconds. The profile modification mode times out if it has not received a command in one minute.2. Toggle the SLC code wheel address to pattern of 0-1-0-1. To toggle the SLC code wheel address,• Set the address to 0• Change the address to 1• Change the address back to 0• Change the address back to 1.NOTE: The LED flashes a single green every half a second when the device is functioning as a distributor. Converting a Distributor Back into a DeviceTo turn a distributor device back to a network device, replace the battery and provide a proper code wheel address. A normal device requires four batteries for trouble-free operation. It is recom-mended to use fresh batteries after the distributor mode.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 43Configuration and Programming Devices3.6.3 Mesh FormationTo add a device to a mesh, refer to the topic, "Mesh Formation with PC Tools" or, to form a mesh network, ensure that the FWSG is powered on and contains a profile. Activate the mesh formation magnet sensor (Figure 2.8, “Mesh Formation Magnetic Sensor on a FWSG”) on the FWSG. RepeaterThe Notifier’s Wireless Sensor Network does not require the use of a dedicated repeater; all wire-less devices act as repeaters. When the repeater function is needed in a location where there is no specific fire function is required, a wireless monitor module or another device can be installed to fulfill the function as a repeater. 3.6.4 Restoring a Device to Factory DefaultRemoving Profiles without PC-based Configuration ToolA device can be restored to factory default state by following the below steps.1. Start with the device powered off. The process is performed during the start-up.2. Power on the device by inserting a single battery into any slot in the device. The LEDs blink yellow twice every five seconds for one minute continuously after inserting the battery. 3. Toggle the code wheel address pattern to 0-159-0. To toggle the SLC code wheel address,• Set the address to 0• Change the address to 159• Change the address back to 0.NOTE: The above illustration depicts the rotary switches being set at address 35 (rotary switch on 'TENS' set at 3 and rotary switch on 'ONES’ set at 5. Ensure that the code wheel address pattern is toggled within 1 minute of inserting the battery. After the code wheel pattern is set, the LEDs in the device blink green five times followed by a sin-gle or double red blink confirming that the device has reverted back to factory default condition.Removing Profile with PC ToolsTo remove a profile in a device using the PC Tools application, do the following:1. Connect the W-USB dongle device to your computer. For more information on USB dongle, refer to Section 4:, "USB Adapter".2. Launch the PC Tools application. Refer Appendix B:, "PC Tools" to know about launching the PC Tools application.3. Go to Site Survey, Create Mesh Network or Diagnostics step.
44 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013Devices Device Operations4. Click Extras and select Reset Devices. The Reset Devices screen appears, displaying the FWSG and other devices that have the profile assigned.5. Click to select the required device and click Reset Device to remove the profile.The profile is removed and the device is reset to factory default state.3.7 Device Operations3.7.1 Modes of OperationFactory DefaultIn this mode, the devices are not associated with the FWSG. A profile must be assigned to associate the device with the FWSG. For further information on assigning a profile, refer to the topic, "Assigning Profile to a Device with an FWSG or Distributor". A device in factory default can be used for site survey. Refer to Appendix A:, "Site Survey". The device cannot perform any fire protection in the factory default state. In this mode, the devices will be viewable in the communicator window of the PC tool with the state displayed as “Factory Default”.Profile AssignedIn this mode, the devices are associated with the FWSG but are not an active participant in the mesh network. A device that is not in the tampered state can join the mesh network in formation or in the rescue mode. For further information on mesh formation, refer to the topic “Mesh Formation Mode” and for further information on rescue mode, refer to the topic “Rescue Mode”. A device in the profile configured state can also be used to distribute profiles. For further information on dis-tributing a profile, refer to 3.6.2 “Distributor Mode”. To remove a profile from a device, refer to 3.6.4 “Removing Profiles without PC-based Configuration Tool”.A device cannot perform any fire protection until it becomes a part of the mesh network. The device will be an invalid reply or no answer at the FACP.In this mode, the devices will be viewable in the communicator window of the PC tool and indi-cates a status of “Profile assigned”.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 45Device Operations DevicesBootloaderIn this mode, the device cannot participate in a mesh and cannot provide fire protection. The device will be available in the communicator window of the PC Tool with a status “Bootloader”.To get a device out of bootloader, refer to the Appendix C:, "Troubleshooting and Testing".DistributorIn this mode the device is functioning as a profile distributor. The device cannot participate in a mesh and cannot provide fire protection. It can be used to share the profile with any device that requests a profile. The device will be available in the communicator window of the PC Tool with a status “Distributor”.Mesh ParticipantDevices that are in the mesh network, no longer communicates directly with the PC Tools applica-tion. The PC Tools application must communicate with the FWSG for status information from the device. The FWSG will respond to the FACP for the device at the address set with the code wheels. The following states are applicable for a device in a mesh network.Mesh Formation ModeIn this mode, the devices are active participants in a mesh that is forming. The LED flashes in the following pattern. First blink green, second blink yellow every 6.8 seconds. The device cannot per-form any fire protection in this state. The device responds to its SLC address with a “DEVICE INIT” or “INIT” trouble.For further information on mesh formation mode, refer to the topic “Mesh Formation”.Initial Mesh Optimization ModeIn this mode, the mesh network is formed and is in the process of establishing stronger communica-tion paths. The LED pattern flashes in the following pattern. Single yellow blink every 6.8 sec-onds. The device cannot perform any fire protection in this state. The device responds to its SLC address with a "DEVICE INIT" or "INIT" trouble.For further information on initial mesh optimization mode, refer to the topic, “Initial Mesh Optimi-zation Mode”.Normal ModeIn the normal mode, the mesh network is formed and provides fire protection. The LED pattern is single green blink every 13.6 seconds. The LED flash can be disabled by panel configuration. If a device is in trouble, it will be indicated by the trouble states. For information on trouble states, refer to the topic “Trouble States with Fire Protection”.Rescue ModeIn the rescue mode, devices that are active participant in the mesh search and retrieve the devices that have lost the communication link. The rescue mode is indicated by the LED pattern of 1 green blink every 6.8 seconds. For more information on rescue mode, refer to the topic, “Rescue Mode”.3.7.2 LED IndicationsThe two LEDs on the devices blink in the same pattern to allow the LED to be viewed from any angle. The LED indications are provided in the table below:
46 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013Devices Device OperationsDuration of LED stateAll units are in seconds. Minute is indicated by M.Example:LegendLED colorNo. of blinksInterval between blink patternsApproximate durationWill transition to next state after 30 min (approx)First blink is green. Second is yellowTwo blinks in this pattern7 sec between blink patterns7M30Condition Action RequiredDevice is ready to updateBootloaderLED Pattern5Device not permitted into the meshConrm device count and software versionDevice is in the mesh & looking for devices that are not in the mesh7Slot request rejectedMesh FormingApp eraseApp loading2New application code is being downloaded730MDevice has returned to factory default stateDevice is now prole assigned.Minimum of 2.5 years battery life remainingDevice is distributing its prole to other devices which requested proleProle removed15Prolereceived10SolidBattery Check - All batteries are freshSolid2.5Distributor mode0.5Device is functioning as normal and searching for lost devicesDevice is functioning as normal and optimizing parent-child connectivityDevice is functioning as normalRescue modeM76Background mesh optimization5M14Normal mode14Use PC based congura-tion tool to initiate the download
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 47Device Operations DevicesDuration of LED stateAll units are in seconds. Minute is indicated by M.Example:LegendLED colorNo. of blinksInterval between blink patternsApproximate durationWill transition to next state after 30 min (approx)First blink is green. Second is yellowTwo blinks in this pattern7 sec between blink patterns7M30Condition Action RequiredLED PatternDevice is factory default Use PC tool to assign prole or activate switch to search for proleDevice is factory default and requesting a prole from a distributor or gatewayClear the tamper condition within 1 minute to enter site surveyDevice is factory default and is ready to enter site surveyPending site survey51MWaiting for prole10Searching for prole0.51MDevice has failed internal self diagnosticsSelf test failDevice is in a congura-tion state.Restart the device. If problem persists. Contact customer supportRestart the device. If problem persists. Contact customer supportDevice has a prole and can be set as distributor or have prole removedSet code wheel pattern to enter the desired modeMinimum of 6 months battery life remainingProle is assigned and device is searching for the meshEnsure the mesh is in rescue mode or wait for timeout to search mesh in formation modeSolidFactory Command1Prole modication51Battery Check - All batteries are presentSolid2.5Searching for mesh (in rescue mode)90 3Ensure the mesh is in formation modeProle is assigned and device is searching for the meshMesh is formed and initializingSearching for mesh (in formation mode)201st Mesh optimization2.5 7
48 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013Devices Device OperationsDuration of LED stateAll units are in seconds. Minute is indicated by M.Example:LegendLED colorNo. of blinksInterval between blink patternsApproximate durationWill transition to next state after 30 min (approx)First blink is green. Second is yellowTwo blinks in this pattern7 sec between blink patterns7M30Condition Action RequiredLED PatternDevice is in the mesh and in trouble condition. Device is in the mesh but has a incorrect SLC addressRefer to the panel to identify the trouble and possible resolutionVerify the address is non duplicate and non zeroDevice has just been tamperedEnsure detector is in the base and module has the face-plate onEnsure detector is in the base and module has the face-plate onDevice is tamperedDevice generic trouble (Eg: Low battery, Partial link condition)14Device address trouble (Eg: Dual address, Zero address)3Battery Check - WeakLess than 6 months or not all 4 batteries presentSolid2.5Device is functioning as normal and has been activatedAlarm state3Sustained tamper12Tamper entrySolid4Ensure all 4 batteries are present or replace the batteries.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 49Device Operations Devices3.7.3 Trouble StatesThe following trouble states are unique to the battery powered RF devices. Multiple troubles states may be active for a single device, but only the highest priority trouble event will be displayed.Trouble States with Fire ProtectionThe devices indicate the following trouble states with a single yellow LED blink every 13.6 sec-onds. The wireless device will still perform fire protection during the following trouble states.Class A FaultThe Class A fault denotes a single connection path from the device. The wireless system is a Class A system requiring two communication paths for normal operations. To remedy the Class A fault, ensure adequate device spacing or the use of a repeater may be required. The wireless mesh is a self healing network. If the trouble is not cleared within 5 minutes, additional actions may be required. Refer to the troubleshooting section for tips on resolving Class A fault conditions.The panel will display "CLASS A FAULT" or "CL A" during a Class A fault condition.Weak LinkThe weak link trouble denotes a connection of insufficient primary signal strength. If you come across such a trouble, ensure adequate device spacing, or the use of a repeater may be required. Tamper the device when moving it to a new location. When the tamper condition is cleared, the FWSG will re-evaluate the signal strength connectivity with the neighboring devices and select the suitable signal paths. Weak link trouble reporting can be disabled at the FACP or at the FWSG for installations not requiring primary link connectivity. Refer to section 2.7.5 for more information on disabling weak link trouble reporting. Refer to the troubleshooting section for more instructions on resolving a weak link condition. The panel displays "WEAK LINK FAULT" or "WEAK" for a device that is in the weak link condi-tion. Low BatteryThe low battery event denotes that:• The device has less than one month power left to perform the required operations. Or • Presence of less than four viable batteries.The low battery event is a latching condition. To clear the low battery event, tamper the device and replace all the four batteries. When a device is tampered, it drops out of the mesh network and attempts to rejoin as soon as the batteries are replaced and the tamper event is cleared. If the device has dropped from the mesh prior to the tamper event, a system reset has to be issued to clear the low battery trouble. The panel displays "BATTERY LOW " or "BAT LOW" during a low battery condition.Trouble States without Fire ProtectionTamperA tamper trouble indicates that a detector is not firmly attached to the base or, in a module, the cover plate is not properly attached. The tamper condition is annunciated in the following ways:Device Indication The LED on the device emits yellow light for 4 seconds followed by a yellow blink once every 12 seconds immediately after the tamper condition.
50 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013Devices Device OperationsPanel Indication Devices that are in the tampered condition reports a latching trouble event. The event is active for 180 seconds before it can be removed with a system reset. Once the event is removed, the device reports a "NO ANSWER' or "INVALID REPLY" until the device is restored or the point is removed from the database.Clearing the Tamper To clear the tamper, • If it is a detector, ensure that the detector is locked together with its base.• If it is a module, ensure that there is a magnet in the cover plate, and is securely fastened to the device in the right orientation.Once the tamper event is cleared, the LEDs in the device emit solid light for 2.5 seconds, in the fol-lowing color patterns that denote the battery status. •Green - All the four batteries are installed and fresh. The device has a minimum one year of normal operation. •Yellow - All the four batteries are installed, and one or more is no longer fresh. This device has- between a minimum of 1 month and 1 year of operation. •Red - One or more of the batteries are low in power and the device has less than a month of operation. After the device displays the current battery condition, it attempts to join the mesh network in the rescue mode or normal mode. This is indicated by a double yellow blink every 3.4 seconds. If a device does not find its mesh in the rescue mode, it searches for its mesh under formation. This is indicated by a double yellow blink every 20 seconds.Duplicate Address Two wireless devices on the same mesh network that are set to the same address reports a duplicate address trouble. The device(s) blink the address fault condition of a single yellow blink every 3.4 seconds. The FWSG will respond to the panel with the device type of the first device to join.The panel displays “DUAL ADDR” or “DUALAD” during a duplicate address condition.No AnswerA device that is not in the mesh, displays a “NO ANSWER” or “INVREP” message at the FACP. Follow the steps in topic, “Mesh Formation Mode” to get a device in the mesh. JammingJamming occurs when a device is overloaded with an interfering RF signal; but is able to send the messages out. A jamming event is detected after 20 seconds of exposure to the jamming signal. In the event of jamming, the LED emits a single yellow blink every 13.6 seconds. Prolonged dura-tions of jamming results in the jammed device dropping from the mesh network. The panel dis-plays “RADIO JAMMING” or “JAM” during a jamming condition.Device InitializationA device reports a device initialization trouble when it is part of a mesh network but is not capable of performing fire protection. This is the case for mesh networks that are still forming and optimiz-ing. The panel displays “INIT MODE” or “INIT” during a device initialization condition.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 51Device Operations Devices3.7.4 Background EventsThe following conditions are not considered a trouble, supervisory, or alarm condition. These events are stored in history of the FACP.Pre-Class A FaultA device will report a pre-Class A event when it first identifies a single connection path condition. If the connection path is not restored or replaced with another viable connection path within 180 seconds a Class A fault condition will be reported. The history event reports this condition as “PRE-CLASS A FAULT”.Device DropA device will report a device drop if it has lost complete communication with the mesh network. If the device does not recover in 180 seconds or less, a "NO ANSWER" or "INVREP" trouble is reported for the address. The history event will report as a “DEVICE DROPPED”.Weak LinkWhen weak link reporting is enabled by the FWSG and disabled in the FACP, then all weak link conditions will be entered as background events in history. The history event is reported as a "WEAK LINK FAULT" or "WEAK" for a device that is in the weak link condition.
52 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013USB Adapter IntroductionSection 4: USB Adapter4.1 IntroductionThe W-USB is an interface that can be connected to a PC through USB. It communicates with the RF devices using the same frequencies as the mesh protocol. This device is powered directly by the USB port.The LED gives an indication of power and initialization status.The W-USB has an adjustable USB connector to facilitate the connection by reducing the size when connected to a PC/laptop. Figure 4.1 W-USB Adapter4.2 Agency Approvals4.2.1 FCCThis device complies with part 15 of the FCC Rules. Operation is subject to the following two con-ditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interferences that may cause undesired operation.FCC ID PV3WFSADPTWARNING: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 53Specifications USB Adapter4.3 Specifications4.3.1 Electrical Specifications4.3.2 Serial Communication Specification4.3.3 Mechanical Specifications4.3.4 Environmental SpecificationsITEM TYP MIN MAX UNITS CommentsOperating Voltage 5 4.3 5.5 VDCSupply Current 33 25 85 mAITEM CommentsUSB Standard USB 2.0 full speedITEM TYP UNITS CommentsUSB connector type ALength 76.2 mm Connector closedLength 96.2 mm Connector openThickness 13 mm Connector sideThickness 8.4 mm Antenna sideWidth 31.2 mmWeight 19.5 gSpecification MIN MAX UNITS CommentsHumidity 10 93 %RH Non CondensingTemperature 0° 50° Celsius Maximum Operating temperature rangeStorage Temperature -10° 60° Celsius
54 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013USB Adapter Driver Installation4.4 Driver InstallationNOTE: Install the PC Tools application before attempting to install the driver.To install a driver, perform the following steps:1. Insert the adapter into the PC. The adapter is detected and is displayed in the Computer Management screen as a Wireless Fire System Dongle.2. Right click on Wireless Fire System Dongle and select Update Driver Software.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 55Driver Installation USB Adapter3. Select Browse my computer for driver software the option.4. Browse to the location of the driver software by clicking Browse. Select the file and click Next. To locate the driver software, go to c:\Program Files\Honeywell\Device Driver. The file resides inside the Device Driver folder.
56 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013USB Adapter Driver Installation5. The confirmation message is displayed that the driver software is updated.6. The device is displayed under ports. The driver is installed.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 57Driver Installation USB Adapter
58 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013Site Survey DescriptionAppendix A: Site SurveyA.1 DescriptionThe site survey allows you to assess and qualify the site for installing the wireless fire alarm sys-tem. The site survey view in the PC tool allows you to view the Radio Frequency (RF) assessment of the site. The tool reports the suggested device spacing based on the data collected during the site survey. This helps to optimize the reliability and performance of the wireless network in the wire-less fire alarm system.A.1.1 Conducting Site Survey at the Job Site The site survey includes two tests:• Link quality test• RF Scan TestThe link test can be conducted individually or it can be done followed by the RF Scan test. This section explains the steps for link quality test and a link quality test followed by RF Scan test.Link Quality TestA link quality test is a quick and repeatable test that provides immediate feedback on the device connectivity. It is conducted primarily to check if there is an event of pocket loss during data trans-mission between devices. In a link test, the device addresses are set in the range of 001 to 100. Basic RequirementsTo conduct a link test, ensure that• You possess two or more devices.• The devices are in factory default condition.NOTE: The LEDs in the device blink red (single or double blink) upon starting the device if it is in a factory default condition. Refer to 3.6.4, "Restoring a Device to Factory Default" for more information on setting the device to factory default state. Conduct a Link TestNOTE: The below procedure lists the steps for conducting only a link test. Hence, examples on the setting the address on devices is explained considering only the link test.To conduct a link test, perform the following steps.1. Remove the batteries if any present from the devices and set the address of the first device as 001.NOTE: For each subsequent device, use the next highest SLC address. For example, set the first device address as 001, second device as 002 and third device as 003. The upper address limit for a device address is 100 while doing a link test.2. Bring the first device to the required location to conduct the test.3. Insert one battery into the factory fresh device. After inserting the battery, the LEDs in the device blink red twice every five seconds if the device is ready for site survey.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 59Description Site SurveyNOTE: You could insert the battery into any available slot. Inserting more than one battery deters the device from entering the site survey mode.4. Clear the tamper condition within one minute of the device startup, to enter the site survey mode. To clear the tamper condition, position the decorative ring around the base of the detector and rotate it in either direction until the ring snaps to its place (Refer to the below image). When you clear the tamper, the device starts the transmission that is denoted by LEDs. Refer to the Table A.1, “Link Test Results-LED Pattern” for results.NOTE: Due to the absence of the second device that is yet to be introduced, the transmission fails. Hence, the LEDs in the first device emits solid red.5. Bring the second device to the required location and repeat the steps 3 and 4. The LEDs in the second device emit yellow light while the test is being conducted.Results of Link TestOnce you have introduced the two devices, the devices start communicating and the link quality test is started. The blinking pattern of the LEDs in the device 002 communicates the results of the link test. To repeat the test, follow the steps 1 to 4.The following table explains the LED patterns during a link test.Table A.1 Link Test Results-LED PatternState Pattern LED Results & DescriptionLInk Test in progressSingle blink every 0.5 seconds. Yellow Transmission of data packets to another device.Solid Red Failure - No Packets receivedSingle blink every 5 seconds. Red Poor -Received only half of the total transmission of data packets or poor signal strength2 blinks every 5 seconds. Red Marginal - Packets partially received or marginal signal strength.3 blinks every 5 seconds. Green Good - All packets received and good signal strength4 blinks every 5 seconds. Green Excellent - All packets received and excellent signal strength
60 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013Site Survey DescriptionTasks After Link Test• Reboot the devices of the link test. To do this, remove and insert the batteries. • After rebooting, do not push the detector back in the base. • The devices can be moved around different locations in the site to optimize the results.• The LED indications will exist until the battery lasts in the devices.• Upon completion of the link test using the devices numbered 001 and 002, you can test the link quality using different set of devices in other required locations. To do so, follow the steps 1 to 5.• Retrieve the site survey results. To retrieve the site survey results, refer to the topic , "Retrieving Site Survey Results"at the end of this section.Link Quality Test and RF Scan TestAn RF Scan test can be conducted following a link test. A Radio Frequency scan test is conducted to assess and measure the background noise and interference, from other wireless systems if any, in the site. The RF Scan test is conducted following the link test. While doing a RF Scan test, the device addresses are set starting from 100 till 159. The below procedure lists the steps for conducting a link test followed by a RF Scan test. Hence, examples on the setting the address on devices is explained considering both the tests.Conduct a Link Test To understand the basic requirements of a link test, refer to the topic, “Basic Requirements”.To conduct a link test, perform the following steps.1. Remove the batteries if any present from the devices and set the address of the first device as 101. For each subsequent device, use the next highest SLC address. For example, set the first device address as 101, second device as 102 and third device as 103. The upper address limit for a device address is 100 while doing a link test.2. Bring the first device to the required location to conduct the test.3. Insert one battery into the factory fresh device in any available slot. Inserting more than one battery deters the device from entering the site survey mode. If the device is ready for site survey, after inserting the battery, the LEDs in the device blink red twice every five seconds.4. Clear the tamper condition within one minute of the device startup to enter the site survey mode. To clear the tamper condition, position the decorative ring around the base of the detector and rotate it in either direction until the ring snaps to its place. Refer to the below image. At this stage, the device starts the transmission. Due to the absence of the second device that is yet to be introduced, the transmission fails. Hence, the LEDs in the first device emits solid red. For more information, Refer to Table A.2, “RF Scan Test Results - LED Pattern”5. Bring the second device to the required location and repeat the steps 3 and 4. The LEDs in the second device emit yellow light while the test is being conducted.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 61Description Site SurveyResults of Link TestOnce you have introduced the two devices, the devices start communicating and the link quality test is started. The blinking pattern of the LEDs in the device 102 communicates the results of the link test. To repeat the test, follow the steps 1 to 4. The link test results stay for 5 minutes and then the RF test begins. You can repeat the test any number of times; the only condition being that the next test should be conducted within five minutes of the last concluded test. Refer to Table A.1, “Link Test Results-LED Pattern” for LED patterns that convey the link quality results. This concludes the link test and the RF Scan test starts. The devices addressed 101 or higher, transition to RF Scan test. On devices addressed below 100, the link test results stay until the bat-tery last. If you are conducting the link test with several devices started in various time frames, it is possible that the devices that start and complete the link test first can transition to RF Scan test, when the devices that began later are still in the link test mode. The RF Scan test may take up to 70 minutes and you have to check the LED patterns for results. The LED patterns are given below.Results of RF Scan TestTable A.2 RF Scan Test Results - LED Pattern Retrieving Site Survey ResultsTo retrieve the site survey results, do the following:1. Reboot the devices by removing and inserting the battery back into the device.2. Plug in the USB adapter into the laptop/PC where you have installed the PC tool.3. Bring the devices within a range of 20ft from the USB adapter. 4. Log into PC Tools application and retrieve the data.State Pattern LED ResultIn Progress- 70 minutes remaining 7 short blinks (Solid) every 30 seconds.Red BadIn Progress- 70 minutes remaining7 short blinks (Solid) every 30 seconds.Yellow MarginalIn progress- 70 minutes remaining7 short blinks (Solid) every 30 second.Green Good
62 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013PC Tools DescriptionAppendix B: PC ToolsB.1 DescriptionThe PC Tools is a standalone desktop windows application. It is a configuration and maintenance tool for an FWSG and devices of the Wireless Sensor Network. It allows you to survey the site, configure the devices and diagnose the wireless network of the Wireless Sensor Network. This tool can be installed on a PC or a laptop. The tool communicates with an FWSG and wireless devices through USB based user interface. You have to connect the USB adapter to the computer to invoke the PC tools application. At any point of time, only one instance of PC Tools application can run on a laptop or PC.The tool has the following utilities.• Site Survey• Creating Mesh Network• DiagnosticsThe PC tool works in a wireless environment with an FWSG and devices within the range of 20 feet.B.2 Launching PC Tools To launch PC Tools application,1. Click Start, point to All Programs, click Wireless Tool, and then Wireless Tool. The following screen is displayed. Alternatively, you can double click the Wireless Tool shortcut in your desktop. 2. Click Start Using. The PC Tools screen is displayed.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 63Launching PC Tools PC ToolsB.2.1 Creating JobsiteYou can create a new jobsite or open an existing one. To create a new jobsite, 1. Perform the steps listed to launch the PC Tools application.2. Click Create from PC Tools screen.3. Enter the name of the new jobsite in the Jobsite Name field. 4. Enter the Location/Description if any, and click Create. 5. The Create Project window opens and displays the name of the jobsite that you created.6. Click Save.The jobsite is created, and the following screen is displayed. You can go to the required function that you want to perform by clicking the Start button in the respective function.
64 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013PC Tools Launching PC ToolsB.2.2 Opening JobsiteIf you have a jobsite already created, you can open the existing jobsite. To open an existing jobsite, 1. Perform the steps listed to launch the PC Tools application.2. Click Open from the PC tools screen.3. Choose the required file from your local drive and click Open against Open Existing Jobsite option. Enter the name of the new jobsite in the Jobsite Name field. The following screen is displayed. You can go to the required function that you want to perform by clicking the Start button in the respective function.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 65Launching PC Tools PC Tools
66 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013Troubleshooting and Testing TroubleshootingAppendix C: Troubleshooting and TestingC.1 TroubleshootingC.2 Testing FWSG and DevicesThe FWSG must be tested after installation and as an integral part of a periodic maintenance pro-gram. The testing methods must satisfy the Authority Having Jurisdiction (AHJ). The FWSG pro-vides optimum performance when tested and maintained in compliance with NFPA 72 ordinances.NOTE: The FWSG used with this base must be tested and maintained regularly following the NFPA 72 ordinances. The FWSG should be cleaned at least once a year.C.2.1 Testing LED IndicationsFor testing LED indications, and for more information on LED indications, refer to the respective chapters and the table provided for LED indications.C.3 Testing Wireless NetworkThe PC Tools application allows you to:• Diagnose and troubleshoot the wireless network and connectivity of the devices. • Monitor the wireless network topology, quality of the communication links between the devices, live and historical event reports for the troubleshooting purpose. Trouble Type Trouble Description ActionWeak link condition The weak link trouble denotes a connection of insufficient primary signal strength.Ensure spacing between devices, or use repeaters. Class A fault condition Device loses the connection with any of the parent devices.Ensure spacing between devices, or use repeaters.Jamming Jamming occurs when a device is overloaded with an interfering RF signal; but is able to send the messages out.If any jammers are installed in the vicinity of the devices, remove them.Low battery The low battery event denotes that the device has less than one month power left to perform the required operations. Or presence of less than four viable batteries.To clear the low battery event, tamper the device and replace all the four batteries. When a device is tampered, it drops out of the mesh network and attempts to rejoin as soon as the batteries are replaced and the tamper event is cleared.Duplicate address Two wireless devices on the same mesh network that are set to the same address reports a duplicate address trouble. Change the address of a device to avoid duplication.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 67Testing Wireless Network Troubleshooting and Testing• View the parent-child relationship and the signal strength between the two devices, and identifies the device that has lost the communication link with the wireless network.In addition to the above, PC Tools application communicates with the FWSG to retrieve the live information about the connectivity and status of the devices. The tool stores the wireless network data such as network map, parent-child information, device information, history events, and net-work statistics.The PC Tools application allows you to retrieve the following information for diagnosing and trou-bleshooting purpose.• Network Topology • History Events• Network Snapshots• Network Statistics• Device AttributesC.3.1 Network TopologyParent-Child DevicesThe parent child relationship between the devices in the wireless network is displayed using the directional arrows.Orphan DevicesThe device that is not linked with any other device in the wireless topology is an orphan device. The device is represented as an orphan device due to one of the following reasons:• The device was originally a part of the wireless network and due to a 'Device Connected' live event, the device sets out of wireless network range.• The device was system configured with the same network ID and hence it was a part of the same wireless network. When the network topology was retrieved, the device detail was not retrieved.• The network connections are saturated and hence parent-child connection with the device is not established.Class A ComplianceEach device must comply with Class A guidelines. The guidelines provide instructions on the required number of parent device for each device to be compliant with the guideline. Following are the compliance requirements.• Class A guideline requirement:Every device must have two parent devices.NOTE: The device image is changed to depict that it does not meet the required guidelines. NOTE: The Class A guidelines are not applicable for the FWSG. Selecting a device from the graphical representation and clicking either left or right allows you to view the following details. The Network Topology window allows you to click either left or right on any connected or orphan device.
68 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013Troubleshooting and Testing Testing Wireless NetworkC.3.2 History EventsThe PC Tools application allows you to retrieve and view the history events of the wireless network for troubleshooting purpose. This report provides information on when the device gets connected with the wireless network, mode change, and the slot change details.C.3.3 Network SnapshotsThe PC Tools application allows you to retrieve and view the network snapshot for troubleshooting purpose. The network snapshot helps you to analyze on how the wireless network is functioning over a period of time.C.3.4 Network StatisticsThe PC Tools application allows you to retrieve and view the network statistics for troubleshooting purpose. The network statistics provides information on the attributes and RSSI of a device. The attributes provide information on the retransmission count and device re-join events. The retrans-mission count is a value equal to the number of times a device retransmits the wireless signal. The device re-join events is a value equal to the number of times the devices gets disconnected from the wireless network and gets connected with the wireless network. The RSSI of a device displays the parent-child relationship between the devices.C.3.5 Device AttributesThe PC Tools application allows you to retrieve and view the attributes of a device for trouble-shooting purpose. The attributes of a device such as low indication, removal indication, level, tam-per fault and others are retrieved.
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 69Index –IndexAAbbreviations 9Abbreviations and Meanings 11Acclimate 38Activating 21activation 24AD FLT 35address 35adjacent 33ambient 39Assign a profile to the Gateway 17Assigning 19, 40Assumed Knowledge 8BBackground 51Basic 58Bootloader 24, 45CClass A 67Class B 15Clearing 50code wheel 42Collapse 30Configuration 17CR123A 38Creating Jobsite 63DDescription 58Device Attributes 68Device Drop 51Device Indication 49device spacing 49Devices 38Configuration and Programming 39Disabling 29, 30Distributor 45dongle 20Driver 54dropped 35Duplicate 50Eevent reporting 22Ffaceplate 42Factory 23, 44FCC 10first blink 19FlashScan 10future 28GGateway 10Description 10Installing FWSG 11Specification Sheet 11Gateway Powered from SLC 15Green 50green light 18IINCOMPAT 34Initialization 50initiate 22Installing Devices 39INVALID REPLY 50isolator 15JJamming 50Jobsite 64Jumper 15LLatching 35LED indications 24Link 58Lock 28Low 49MMagnet 41Magnet switch activations 24Magnetic 42MAX GW 35Mesh 23, 24Mesh Formation 18Mesh Participant 45Modes 44Monitor Module 38Mounting 12MS FRM 23NNetwork Snapshots 68
70 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013–IndexNetwork Statistics 68NFPA 66No Answer 50NO DEV 23NO MSH 23Non-latching 34Normal 24Normal Mode 45OOPT MS 34Optimization 23Orphan Devices 67overlap 33overlapping 35PPanel Indication 50participant 44Password Reset 29peripheral 23Photoelectric 38PR MIS 23Profile 23PROFILE MISSING 23pull station 38Purpose 8RRadio 11Red 50Removing 18Repeater 43repeater 43, 49Rescue 24Restrictions 33Retrieving 61RF emitters 34RF Scan 60rotary switches 43Ssecond blink 19sensor 23settings 29single 43single red 18Site Survey 8SLC Configuration 21SLC processor 34SLOT 36spectrum 33Start 22SWITCH ACCESS 36TTamper 50test marker 41toggles 24transmission 23Trouble 34trouble-free 42Uunique 24USB Adapter 52Wwalkie-talkie 36Weak 29, 49Weak Link 51With 19Without 17YYellow 50
PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 71Changes & Comments LS10036-000NF-E:N0 Revise to: UL change? Brief description:
Changes & Comments LS10036-000NF-E:N072 PRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013
Manufacturer Warranties and Limitation of LiabilityManufacturer Warranties. Subject to the limitations set forth herein,Manufacturer warrants that the Products manufactured by it in itsNorthford, Connecticut facility and sold by it to its authorizedDistributors shall be free, under normal use and service, from defectsin material and workmanship for a period of thirty six months (36)months from the date of manufacture (effective Jan. 1, 2009). TheProducts manufactured and sold by Manufacturer are date stamped atthe time of production. Manufacturer does not warrant Products thatare not manufactured by it in its Northford, Connecticut facility butassigns to its Distributor, to the extent possible, any warranty offeredby the manufacturer of such product. This warranty shall be void if aProduct is altered, serviced or repaired by anyone other thanManufacturer or its authorized Distributors. This warranty shall alsobe void if there is a failure to maintain the Products and the systems inwhich they operate in proper working conditions.MANUFACTURER MAKES NO FURTHER WARRANTIES, ANDDISCLAIMS ANY AND ALL OTHER WARRANTIES, EITHEREXPRESSED OR IMPLIED, WITH RESPECT TO THE PRODUCTS,TRADEMARKS, PROGRAMS AND SERVICES RENDERED BYMANUFACTURER INCLUDING WITHOUT LIMITATION,INFRINGEMENT, TITLE, MERCHANTABILITY, OR FITNESS FORANY PARTICULAR PURPOSE. MANUFACTURER SHALL NOT BELIABLE FOR ANY PERSONAL INJURY OR DEATH WHICH MAYARISE IN THE COURSE OF, OR AS A RESULT OF, PERSONAL,COMMERCIAL OR INDUSTRIAL USES OF ITS PRODUCTS.This document constitutes the only warranty made by Manufacturerwith respect to its products and replaces all previous warranties and isthe only warranty made by Manufacturer. No increase or alteration,written or verbal, of the obligation of this warranty is authorized.Manufacturer does not represent that its products will prevent any lossby fire or otherwise.Warranty Claims. Manufacturer shall replace or repair, atManufacturer's discretion, each part returned by its authorizedDistributor and acknowledged by Manufacturer to be defective,provided that such part shall have been returned to Manufacturer withall charges prepaid and the authorized Distributor has completedManufacturer's Return Material Authorization form. The replacementpart shall come from Manufacturer's stock and may be new orrefurbished. THE FOREGOING IS DISTRIBUTOR'S SOLE ANDEXCLUSIVE REMEDY IN THE EVENT OF A WARRANTY CLAIM. Warn-HL-08-2009.fmPRELIMINARY: Notifier Wireless Sensor Network — P/N LS10036-000NF-E:N0 10/10/2013 73
World Headquarters12 Clintonville RoadNorthford, CT 06472-1610 USA203-484-7161fax 203-484-7118www.notifier.com

Navigation menu