Honeywell KX165A KX165A VHF Navigation / Communications Transceiver User Manual Installation Manual

Honeywell International Inc. KX165A VHF Navigation / Communications Transceiver Installation Manual

Installation Manual

INSTALLATION MANUALKX 155A/165ACOMM/NAV SYSTEMMANUAL NUMBER 006-10542-0002REVISION 2, APRIL 2000PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
WARNINGPrior to Export of this Document, review for export license requirement is needed.COPYRIGHT NOTICE ©2000 Honeywell International Inc.Reproduction of this publication or any portion thereof by any means without the express writtenpermission of Honeywell is prohibited. For further information contact the Manager, TechnicalPublications, Honeywell, One Technology Center, 23500 West 105th Street Olathe KS 66061Telephone: (913) 782-0400.PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 1-1Rev 2, Apr/2000SECTION IGENERAL INFORMATION1.1 INTRODUCTIONThis manual contains information relative to the physical, mechanical, and electrical characteris-tics of the Bendix/King Silver Crown KX155A VHF COMM Transceiver/Navigation/VOR/LOC Glideslope Receiver. Installation and operating procedures are also included. Information relative to the maintenance, alignment, and procurement of replacement parts may be found in the KX155A Maintenance/Overhaul Manual, P/N 006-15542-XXXX.1.2 EQUIPMENT DESCRIPTIONThe KX155A is a VHF NAV/COMM Transceiver which provides the following functions.A. Two-way voice communication within the frequency range of 118.00 MHz to 136.975 MHz (760 Channels) in 25 kHz increments.B. Reception of navigation signals within the frequency range of 108.00 MHz to 117.95 MHz in 50 kHz increments (200 channels).C. Optional reception of glideslope signals within the frequency range of 329.15 MHz to 335.00 MHz in 150 kHz increments (40 channels).D. High level speaker audio output plus limited audio intercom inputs and out-puts.E. Provides a count down timer.The KX155A is a panel mounted unit. Connections to the unit are made through one 36 and one 50 pin Molex printed circuit board edge connector and three BNC coax connectors at the rear of the unit.Electrically, the KX155A consists of the following sections:•COMM Transmitter•COMM Receiver•NAV Receiver•Main Board •Glideslope Receiver and Converter (Optional)•Gas Discharge Display•4 Ω Audio Amplifier The KX155A is backward compatible with existing KX155 installations. See Section 2.3 Additional Installation Notes for details.PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEMPage 1-2 10542I02.ZIPRCDRev 2, Apr/20001.3 TECHNICAL CHARACTERISTICSTable 1-1 KX155A/KX165A Technical SpecificationsKX155A/KX165A GENERAL SPECIFICATIONSENVIRONMENTAL TSO COMPLI-ANCE: RTCA DO-160C, Eurocae ED-14C Env Cat (see Appendix E)TEMPERATURE RANGE: -20°C to +55°C with short time operation at +70°C.(Operational to -40°C)ALTITUDE: -15,000 feet to 50,000 feetWEIGHT:KX 155A VERSIONS WEIGHT Mtg Rack(nominal) w/hardware069-01032-0101 4.2 lbs (1.9 kg) 1.1 lbs (0.5 kg)069-01032-0201 3.7 lbs (1.7 kg) 1.1 lbs (0.5 kg)VERSIONS WEIGHT Mtg Rack(nominal) w/hardwareKX 165A 069-01033-0101 4.0 lbs (1.8 kg) 1.1 lbs (0.5 kg)069-01033-0201 4.0 lbs (1.8 kg) 1.1 lbs (0.5 kg)PHYSICAL DIMENSIONS (NOMINAL) : Width: 6.25 inches (15.875 cm) Height: 2.00 inches (5.08 cm) Depth: 10.16 inches (25.81 cm) to end of connectorMOUNTING: Panel mounted, no shock mounting requiredPOWER CONSUMPTION:RECEIVE TRANSMITVERSIONS: TYP. PEAKPRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 1-3Rev 2, Apr/2000069-01032-0101 0.8 A 2.2 A 6.0 A (MAX)069-01032-0201 0.8 A 2.2 A 6.0 A (MAX) 069-01033-0101 0.6 A 0.7 A 4.0 A (MAX) 069-01033-0201 0.6 A 0.7 A 4.0 A (MAX) NOTE: Peak currents occur only when installation is configured for the 4Ω audio output & both COMM and NAV volumes are adjusted to full.Specifications are at 25°C unless otherwise specified.COMM TRANSCEIVERTSO COMPLIANCE: Transmit: C37d (DO-186A, Class 4 - all flavors/ Class 4 & 6 069-01033-0201) Receive: C38d (DO-186A, Class C & D - all flavors/ Class C, D, & E 069-01033-0201)APPLICABLE DOCUMENTS: RTCA DO-186A, DO-160C, *EUROCAE ED-23B, ED-14C DUTY CYCLE: 10%, 4.5 minutes receive, 0.5 minutes transmitFREQUENCY RANGE: 118.000 MHz to 136.975 MHzCOMM TRANSMITTERPOWER OUTPUT: 10 Watts minimum10 Watts typical (KX 155A pre-Mod 5)MODULATION: 70% minimum modulation capability with less than 15% distortion. Audio leveling circuit used. SIDETONE OUTPUT: Adjustable up to 100 mW ( 5.1 mW Mod 1 w/o Mod 6) into 500 Ω headphonesMICROPHONE: Standard carbon or dynamic mic containing transistorized pre-amp. (Must provide 100 mVrms into 100 Ω load.)PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEMPage 1-4 10542I02.ZIPRCDRev 2, Apr/2000HARMONIC CONTENT: -56 dBc, minimum. Typically greater than -60 dBcHIGH TEMPERATURE PROTEC-TION: If the transmitter and modulator circuits become hot enough to potentially damage any components in the transceiver, a protection circuit will automatically reduce the transmitter power consumption and output power.TRANSMITTER TIME OUT: If MIC key is enabled for greater than 30 ( Nominal) sec-onds, the transmitter will shut down. The transmitter is re-set upon release of MIC key.PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 1-5Rev 2, Apr/2000COMM RECEIVERRECEIVER SENSITIVITY: -107 dBm (2µV hard) or less for 6 dB S + N/N with 1,000 Hz tone modulated 30 %.RECEIVER SELECTIVITY: Class C & D operating modes 6 dB bandwidth ±8.0 kHz, minimum60 dB bandwidth ±22.0 kHz, maximum Class E operating mode 6 dB bandwidth ±2.778 kHz, minimum60 dB bandwidth ±7.37 kHz, maximumRECEIVER AUDIO OUTPUT: 100 mW into 500 Ωs minimum.AGC CHARACTERISTICS: From -93 dBm to -33 dBm audio output will not vary more than 3 dB. Active from no signal to +3 dBm.SQUELCH: Automatic squelch (internally adjustable carrier to noise setting) with manual disable and carrier squelch override. Both squelch adjustments are externally accessible. The automatic squelch has a typical factory setting of -106 dBm.OUT OF BAND SPURIOUS RESPONSE, INTERMODULATION AND DESENSITIZATIONAt least 60 dB downNAV RECEIVERTSO COMPLIANCE: C36e (DO-195, Class A) LocalizerC40c (DO-196) VORAPPLICABLE DOCUMENTS: RTCA DO-195, RTCA DO-196, RTCA DO-160C*EUROCAE ED-22B, & ED-46B, ED-14CFREQUENCY RANGE: 108.00 MHz to 117.95 MHz in 50 kHz incrementsOUT OF BAND SPURIOUS RESPONSES, INTERMODULATION ANDDESENSITIZATION:At least 60 dB downMeets ICAO FM Immunity requirements consis-tent with RTCA DO-195,196 and *Eurocae ED-22B,46B* Pre-Mod 5 units may not meet all applicable EUROCAE requirements.PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEMPage 1-6 10542I02.ZIPRCDRev 2, Apr/2000VOR COURSE ACCURACY: Two sigma limit 3° as specified in RTCA DO-196 when used with indicators per section 1.7.3 of this installation manual.Three sigma limit 2.7° as specified in *Eurocae ED-22B when used with indicators per section 1.7.3 of this Installation manual.AUDIO OUTPUT: With a 1 kHz tone 30% modulation at least 100 mW output into 500 Ω loadsIDENT/VOICE: With 100 mV input, 30% modulation at 1020 Hz, the ident/voice tone ratio shall not be less than 15 dB.LOC CENTERING ERROR: Two sigma limit ±9.9 µA as specified in RTCA DO-195 and *Eurocae ED-46B when used with indica-tors per section 1.7.2 of this installation manual.GLIDESLOPE RECEIVERTSO COMPLIANCE: C34e (DO-192)APPLICABLE DOCUMENTS: RTCA DO-192, DO-160C*EUROCAE ED-47B, ED-14CCENTERING ACCURACY: Two sigma limit ±10µA as specified in RTCA DO-192 and *Eurocae ED-47B when used with indica-tors per section 1.7.1 of this Installation Manual.DEFLECTION CHARACTERISTICS: A difference in depth of modulation of 0.091 ddm, or 2 dB, shall produce a deflection of 78 ±3µA (typical). The deviation under opposite polarity shall be 78 ±3 µA (typical).FREQUENCY RANGE: 329.15 MHz to 335.00 MHz 40 channels (150 kHz spacing).SPURIOUS RESPONSE: All responses in the range from 90 kHz to 1500 MHz at least 60 dB below center frequency re-sponse, excluding the range from 328.60 MHz to 335.40 MHz.* Pre-Mod 5 units may not meet all applicable EUROCAE requirements.PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 1-7Rev 2, Apr/20001.4 UNITS AND ACCESSORIES SUPPLIED1.4.1 KX 155A/KX 165AThe Bendix/King KX 155A/KX 165A Transceivers are available in the following configurations.Table 1-2 KX 155A Configurations AvailableVOR/LOC CONVERTER (KX 165A ONLY)TSO COMPLIANCE: C40c (DO-196)C36d (DO-195, Class A)ACCURACY - VOR: Typical bearing error of less than 0.5° with preci-sion track selector (2° max. error). - LOC: Typical centering error of less than 3µA (7µA max error).COURSE WIDTH: VOR: 10° ±1° externally adjustable LOC: 90 µA ±5µA for ddm 0f 0.093 ddm of 4 dBINPUT IMPEDANCE: 60 kΩ for 0.5 Vrms input (VOR mode)LOADS: Five 1000Ω deviation loads, three 1000Ω flag loads and three 200Ω from-to loadsAUDIO AMP (KX 155A ONLY)4 Ω Output: 8 watts nominalInputs: Three 500 Ω Auxiliary Inputs* Pre-Mod 5 units may not meet all applicable EUROCAE requirements.Part Number 28V Glideslope Receiver069-01032-0101 X X069-01032-0201 XPRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEMPage 1-8 10542I02.ZIPRCDRev 2, Apr/20001.4.2 INSTALLATION KITBendix/King KX 155A/KX 165A Installation Kit (P/N 050-03378-0000/0001), listed in Table 1-4 contains the following parts: 0000 for units with glideslope and 0001 for units without glideslope.Table 1-3 KX 165A Configurations AvailablePart Number 28V 8.33 kHz069-01033-0101 X069-01033-0201 X XPRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 1-9Rev 2, Apr/2000Table 1-4 Installation Kit (050-03378-XXXX)1.5 ACCESSORIES REQUIRED BUT NOT SUPPLIEDA. Broad band 50 Ω vertically polarized Communications antenna with coaxial cable.B. Headphones: 500 Ωs nominal impedance.C. Microphone: Low impedance carbon or dynamic with transistorized pre-amp.D. Broad band 50 Ω horizontally polarized Navigation antenna with coaxial cable.E. Broad band 50 Ω horizontally polarized Glideslope antenna with coaxial cable or low loss splitter used with the navigation antenna.F. VOR, LOC, Glideslope Indicators. See section 1.7.6 for TSO’d systems.G. In some installations it may be desirable to allow the Glideslope Receiver to oper-ate using the aircraft’s navigation antenna. In other installations it may be desirable to operate two NAV/LOC Receivers or two GS Receivers using a common anten-na. Low-loss couplers are available to allow such operation.An overall degradation in sensitivity will be realized due to the insertion loss of the coupler. The installer must verify that acceptable sensitivity and proper system Part Number Description 0000 0001030-00101-0002 PANEL MOUNT PLUG 3 2030-01094-0060 CONN 18 POS 1 1030-01094-0088 CONN HOUSING (2 X 2.50 ) W POLARIZING KEY11030-01107-0078 CONNECTOR TERM 78T 1 0030-01107-0068 CONNECTOR TERM 68T 0 1047-05959-0002 STRAIN RELIEF W/H 2 2047-05960-0001 STRAIN RELIEF W/F 2 2073-00431-0007 CONN MTG PLATE COMPLETE 1 1089-02051-0024 NUT, SPEED, U, 6-32 4 4089-02353-0001 NUT, CLIP, 6-32 6 6089-05878-0005 SCR, PHP, 4-40 X 5/16 2 2089-05878-0012 SCR, PHP, 4-40 X 3/4 4 4089-05907-0006 SCR, PHP, 6-32 X 3/8 4 4089-06012-0008 SCR, FHP, 6-32 X 1/2 6 6090-00019-0007 RING, RTNR, .438 3 2PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEMPage 1-10 10542I02.ZIPRCDRev 2, Apr/2000performance is realized in a system that utilizes a coupler. A minimum of 20 dB of GS receiver-to-receiver isolation is required in dual installations employing a KX 155A/KX 165A GS receiver. Examples of some common couplers are listed below. Contact the coupler manufacturer for specifications for the couplers listed.Table 1-5 Common Couplers 1.6 LICENSE REQUIREMENTS The KX 155A/KX 165A NAV/COMM transceiver is to be utilized in an aircraft which already has a station license, no additional radio station license is required.If the transceiver is to be used as a ground station then a Ground Station Authorization is required. Call the Federal Communications Commission (FCC) at 1-800-322-1117, or use the included FCC Form 207, to order FCC Form 406, “Application for Ground Station Authorization in the Aviation Services”.You may also use the FCC’s FAX form service by calling 1-202-418-0177.This equipment has been accepted by the FCC and entered into their list of Type Accepted Equip-ment as AlliedSignal Avionics, Inc. Model KX 155A/KX 165A.For more information call the FCC Hot line at 1-800-322-1117, press “2" for assistance with radio service, then press “1" for ship and aircraft licensing information. To get information from the in-ternet, visit the FCC web page at http://www.fcc.gov.The KX 155A/KX 165A owner/operator accepts all responsibility for obtaining the proper licensing before using the transmitter.THE VHF TRANSMITTER IN THIS EQUIPMENT ISGUARANTEED TO MEET FEDERAL COMMUNICATIONSCOMMISSION ACCEPTANCE OVER THE OPERATINGTEMPERATURE RANGE ONLY WHEN A BENDIX/KINGCRYSTAL IS USED IN THE STABILIZED MASTER OSCIL-LATOR.USE OF OTHER THAN A BENDIX/KING CRYSTAL ISCONSIDERED AN UNAUTHORIZED MODIFICATION,AND WILL VOID THE WARRANTY.Coupler to allow oneantenna to operate: Dayton-Granger(954) 463-3451 Dorne Margolin(516) 585-4000One Nav and one GS GSNC 20-05 H22-1Two Navs DRC 20-04 or 14830 H21-1Two Glideslopes DGSC 20-02 or 16009 H24-1Two Navs and two GSs DOC 20-06 or 16010 H69-1CAUTIONPRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 1-11Rev 2, Apr/2000An Aircraft Radio Station License is no longer required for this equipment for domestic operation. For international travel, forms (FCC Form 404, New Aircraft Station License, or FCC Form 405A, Renewal of Aircraft Station License) can be obtained from your nearest FCC Field Office.1.7 REQUIREMENTS FOR TSO’D VOR/ILS GLIDESLOPE SYSTEMSThe additional units used in conjunction with the KX 155A/KX 165A must meet the specifications listed below to comprise a completely TSO’d navigation system.1.7.1 KX 155A/KX 165A GLIDESLOPE INDICATOR REQUIREMENTS A. The indicator shall meet all applicable requirements of TSO C34e.B. Centering current to be 0 ±6.6 µA with a 95% probability under all environ-mental conditions listed in RTCA Paper DO-192, Minimum Performance Standards -- Airborne ILS Glideslope Receiving Equipment, Paragraph 2.1, sub-paragraph B, Centering Accuracy.C. The course deviation pointer shall visibly deflect at least ±5/8 inch along its scale when the input current is changed from zero to ±150 µA.D. Deflection linearity over the deflection range from zero to 150 µA shall be with-in 10% of being proportional to the input current. Additionally, as the current is increased beyond that producing full scale deflection to a value of ±685.7 µA, the indicator deflection shall not decrease.E. When the input current is abruptly changed from any value from zero to ±150 µA, the pointer shall reach 67% of its ultimate deflection within 2 seconds and pointer overshoot shall not exceed 5%.F. The input impedance shall be 1 K Ωs ±5% for both the deviation indicator and warning signal.G. A warning signal input current of 150 µA or less shall produce a fully visible warning flag. A warning signal input current of 260 µA or greater shall produce a fully concealed warning flag.1.7.2 KX 155A LOCALIZER CONVERTER AND INDICATOR REQUIREMENTS A. The indicator shall meet all applicable requirements of C36e (RTCA DO-195 Class A) or C36d (RTCA DO-131 Class D).B. Centering current to be 0 ±6.0 µA with a 95% probability under all environ-mental conditions listed in RTCA Paper DO-195, Minimum Performance Standards -- Airborne ILS Localizer Receiving Equipment, Paragraph 2.1, sub-paragraph b, Centering Accuracy.C. The course deviation pointer shall visibly deflect at least ±3/8 inch along its scale when the input current is changed from zero to ±90 µA.D. Deflection linearity over the deflection range from zero to ±90 µA shall be with-in 10% of being proportional to the difference in depth of modulation of the 90 and 150 Hz signals, or the deflection shall be within 5% of standard deflection (±90 µA) of being proportional to the difference in depth of modulation, which-ever is greater. Additionally, as the difference in depth of modulation is in-creased beyond that producing full scale deflection (±150 µA) to a value of 0.4 ddm, the course deviation pointer deflection shall not decrease.PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEMPage 1-12 10542I02.ZIPRCDRev 2, Apr/2000E. When the input current is abruptly changed from zero to ±150 µA, the pointer shall reach 67% of its ultimate deflection within 2 seconds and pointer over-shoot shall not exceed 5%.F. The input impedance of the indicator for both the deviation indicator and warn-ing signal shall be 1 KΩ ±5%.G. A warning signal input current of 125 µA or less shall produce a fully visible warning flag. A warning signal input current of 260 µA or greater shall pro-duce a fully concealed warning flag.1.7.3 KX 155A VOR CONVERTER AND INDICATOR REQUIREMENTS A. The indicator shall meet all applicable requirements of TSO C40c.B. The bearing error shall be less than 2.5° with a 95% probability under all en-vironmental conditions listed in RTCA Paper DO-196, Minimum Performance Standards -- Airborne VOR Receiving Equipment, Paragraph 2.1, sub-para-graph 2.1.2, Bearing Accuracy.NOTEFor older converters/indicators, the Bearing Error shall be less than 2.7° with a 95% probability under all environmental conditions listed in RTCA Paper DO-114, MINIMUM PERFORMANCE STANDARDS -- AIRBORNE VOR RECEIVING EQUIPMENT, Paragraph 2.1, Sub-paragraph B, BEARING ACCU-RACY.C. The course deviation pointer shall visibly deflect at least ±1/2 inch (for DO-196) or 3/8 inch (for DO-114) along its scale when the input current is changed from zero to ±150 µA.D. Deflection LinearityThe deflection shall be proportional to the change in phase between the two components of the standard VOR test signal, within 20% of the deflection pro-duced by a 10° (±150 µA) change in phase. This requirement shall be met at all deflections produced when the phase difference is varied from plus 10° to minus 10° of that producing an "on course" indication.The pointer deflection shall not decrease as the phase difference is increased from producing an "on course" indication to that producing an indication which is equivalent to ±80° from "on course".E. Deflection ResponseWhen the difference in phase between the two components of an "on course" standard VOR test signal is abruptly changed, the pointer shall reach 70% of its ultimate position within 3 seconds and the pointer overshoot shall not ex-ceed 20%.F. The input impedance of the indicator for both the bearing error and warning signal shall be 1 KΩ ±5%.PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 1-13Rev 2, Apr/2000G. A warning signal input current of 125 µA or less shall produce a fully visible warning flag. A warning signal input current of 266 µA or greater shall pro-duce a fully concealed warning flag.H. The input impedance of the TO/FROM indicator shall be 200 Ωs ±200 µA sensitivity.1.7.4 KX 165A VOR INDICATOR REQUIREMENTSA. The indicator shall meet all applicable requirements of TSO C40c.B. The bearing error shall be less than 1.9° with 95% probability under all environmen-tal conditions listed in RTCA Paper DO-196, Minimum Performance Standards -- Airborne VOR Receiving Equipment, Paragraph 2.1, sub-paragraph 2.2.1, Bearing Accuracy.NOTEFor older indicators, the Bearing Error shall be less than2.7° with a 95% probability under all environmentalconditions listed in RTCA Paper DO-114, MINIMUMPERFORMANCE STANDARDS -- AIRBORNE VORRECEIVING EQUIPMENT, Paragraph 2.1, Sub-paragraph B, BEARING ACCURACY.C. The course deviation pointer shall visibly deflect at least ≈1/2 inch (for DO-196) 3/8 inch (for DO-114) along its scale when the input current is changed from zero to ±150 µA.D. Deflection LinearityThe deflection shall be proportional to the change in phase between the two com-ponents of the standard VOR test signal, within 20% of the deflection produced by a 10° (±150 µA) change in phase. This requirement shall be met at all deflections produced when the phase difference is varied from plus 10° to minus 10° of that producing an “on course” indication.The pointer deflection shall not decrease as the phase difference is increased from the producing an “on course” indication to that producing an indication which is equivalent to ±80° from “on course”.E. Deflection ResponseWhen the difference in phase between the two components of an “on course” stan-dard VOR test signal is abruptly changed, the pointer shall reach 70% of its ultimate position within 3 seconds and the pointer overshoot shall not exceed 20%.F. The input impedance of the indicator for both the bearing error and warning signal shall be 1 KΩ ±5%.G. A warning signal input current of 50 µA or less shall produce a fully visible warning flag. A warning signal input current of 350 µA or greater shall produce a fully con-cealed warning flag.H. The input impedance of the TO/FROM indicator shall be 200 Ω ±200 µA sensitivity.PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEMPage 1-14 10542I02.ZIPRCDRev 2, Apr/20001.7.5 KX 165A LOCALIZER INDICATOR REQUIREMENTSA. The indicator shall meet all applicable requirements of C36e.B. The localizer centering current to be 0 ±3.2 µA with a 95% probability under all environmental conditions listed in RTCA DO-195, Minimum Performance Standards -- Airborne ILS Localizer Receiving Equipment, Paragraph 2.2.1, sub-paragraph B, Centering Accuracy.C. The course deviation pointer shall visibly deflect at least ±3/8 inch along its scale when the input current is changed from zero to ±90 µA.D. Deflection linearity over the range from zero to ±90 µA shall be within 10% of being proportional to the difference in depth of modulation of the 90 and 150 Hz signals, or the deflection shall be within 5% of standard deflection (±90 µA) of being proportional to the difference in depth of modulation, whichever is greater.Additionally, as the difference in depth of modulation is increased beyond that producing full scale deflection (±150 µA) to a value of 0.4 ddm, the course de-viation pointer deflection shall not decrease.E. When the input current is abruptly changed from zero to ±150 µA, the pointer shall reach 67% of its ultimate deflection within 2 seconds and pointer over-shoot shall not exceed 5%.F. The input impedance of the indicator for both the deviation indicator and warn-ing signal shall be 1 KΩ ±5%.G. A warning signal input current of 50 µA or less shall produce a fully visible warning flag. A warning signal input current of 350 µA or greater shall pro-duce a fully concealed warning flag.1.7.6 FULLY TSO’D SYSTEMSThe following systems when used in conjunction with the KX 155A will meet all TSO system re-quirements.1. KI 2032. KI 2043. KI 208/A4. KI 209/A5. KN 72, KI 2066. KN 72, KI 525A7. KN 72, KPI 5528. KN 72, KPI 5539. KN 72, KI 202PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 2-1Rev 2, Apr/2000SECTION IIINSTALLATION2.1 GENERAL This section contains suggestions and factors to consider before installing the KX 155A/KX 165A. Close adherence to these suggestions will assure a more satisfactory performance from the equipment.The conditions and tests required for TSO approval of this article are minimum performance stan-dards. It is the responsibility of those desiring to install this article either on or within a specific type or class of aircraft to determine that the aircraft installation conditions are within TSO stan-dards. The article may be installed only if further evaluation by the applicant documents an ac-ceptable installation and is approved by the Administrator.2.2 UNPACKING AND INSPECTING EQUIPMENT Exercise extreme care when unpacking the unit. Make a visual inspection of the unit for evidence of damage incurred during shipment. If a claim for a damage is to be made, save the shipping container to substantiate the claim. When all equipment is removed, place all packing materials in the shipping container for use in unit storage or reshipment.2.3 EQUIPMENT INSTALLATION The KX 155A/KX 165A installation will conform to standards designated by the customer, install-ing agency and existing conditions as to the unit location and type of installation. However, the following suggestions should be considered before installing your KX 155A/KX 165A. The install-ing agency will supply and fabricate all external cables. The connectors required are supplied by AlliedSignal. Interconnect diagrams are Figures 2-12 through 2-16.NOTEUse good quality stranded wire with at least 600 volt insula-tion that will not support a flame. If more than one Glides-lope Receiver is to be operated from a single antenna, anantenna coupler such as the DORNE and MARGOLIN INC.(Model DMB H4-1) or equivalent should be used.2.3.1 AVIONICS COOLING REQUIREMENTS FOR PANEL MOUNTED EQUIPMENT The greatest single contributor to increased reliability of all modern day avionics is to limit the max-imum operating temperature of the individual units. While modern day individual circuit designs consume much less electrical energy, the watts per cubic inch dissipated within avionics units re-mains much the same due to high density packaging techniques. Consequently, the importance of providing avionics stack cooling is still with us.Forced air cooling is required for the KX 155A/KX 165A. Forced air must be provided to the KX 155A/KX 165A through the air inlet port located on the back of the unit. Forced air must be sup-plied by a source capable of delivering a minimum air flow of 3.5 CFM to the unit under the static pressure conditions that will exist at the unit’s air inlet port (typically, not more than .032 psi relative to ambient pressure). In order to maintain frequency stability per TSO specifications, the blower’s inlet air temperature must not exceed 55° C. However, in order to provide optimum equipment reliability, it is strongly recommended that inlet air temperature not exceed 35° C.PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
Page 2-2 10542I02.ZIPRCDRev 2, Apr/2000BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEMRecommendations on stack cooling are contained in AlliedSignal Installation Bulletin #55. Failure to provide stack cooling will certainly lead to increased avionics maintenance costs and may void the AlliedSignal warranty.2.3.2 MOUNTING RACK INSTALLATION A. The KX 155A/KX 165A is mounted rigidly in the aircraft panel. Select a posi-tion in the panel that is not too close to any high external heat source. Re-member to allow adequate space for installation of cables and connectors. Avoid sharp bends and placing the cables near aircraft control cables.B. Refer to Figure 2-10 for the KX 155A/KX 165A mounting dimensions. Mark and drill the mounting holes.C. Secure the mounting rack to the instrument panel per Figure 2-11. The rear mounting bosses should be attached to the aircraft by means of support brackets.2.3.3 ANTENNA INSTALLATION A. Conventional 50 ohm horizontally polarized NAV Glideslope and vertically po-larized COMM antennas are required with the KX 155A/KX 165A. Vertically bent whip antennas are not recommended. Wideband COMM antennas pro-vide efficient operation over the COMM band. Antennas should be installed per manufacturer’s recommendations. Additional recommendations are as follows:1. COMM Antennaa. Mount antenna on flat metal surface or install a ground plane at least 18 inches square.b. The antenna should be well removed from any projections and the engine(s) and propeller.2. Navigation Antennae (VOR/LOC & Glideslope)a. The location should be well removed from other antennas, projec-tions and engine(s). It should have a clear line of sight area if pos-sible.b. The antenna must be mounted symmetrically with the centerline of the aircraft.c. Avoid running other coaxial and wires near the NAV antenna cable.B. The antenna connectors on the KX 155A/KX 165A are identified on the rear die casting. NOTEWith KX 155A/KX 165A viewed from the front, the NAV an-tenna connector is on the right and the COMM antenna con-nector is on the left. This means that the NAV FrequencySelector and NAV Antenna are on the same side of the ra-dio. The COMM Frequency Selector and COMM AntennaConnector are also on the same side of the radio. TheGlideslope Antenna Connector is right above the NAV An-tenna Connector.PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 2-3Rev 2, Apr/20002.3.4 CABLE HARNESS AND CONNECTOR ASSEMBLY The KX 155A/KX 165A uses a special connector that mates directly with the printed circuit board inside the unit. Assembly of the connector is as follows:A. Contact Terminal Assembly using Molex Crimper (Figure 2-1 through 2-6)1. Strip each wire 5/32" for contact terminal (Part Number 030-01107-XXXX). (The last two digits of the contact terminal part number indicatesthe number of terminals required).2. Open the Molex hand crimper HT 1921 with the engraved side towardthe operator. Place the conductor tab section of a contact terminal onAnvil B with the contact portion facing away from the operator. Close thecrimper slightly until the contact tabs touch the female jaw.3. Insert the stripped conductor until the insulation is even with the side ofthe crimper facing the operator. Crimp the conductor tabs by squeezingthe handles together until the jaws are fully closed or a sufficient crimpis obtained.4. Move the lead to Anvil A. Place the insulating tab section on Anvil A.Crimp again until the jaws are fully closed or a sufficient crimp is ob-tained.B. Contact Insertion into Molex Connector Housing1. After the contact terminals have been installed on the wiring harness, thecontact terminals can be inserted into the proper location in the connec-tor housing (P/N 030-01094-00XX). The terminal cannot be inserted up-side down. Be sure to push the terminal all the way in, until a click canbe felt or heard.2. The self locking feature can be tested by gently pulling on the wire.C. Location of Polarizing Key in Housing1. Prior to insertion of connector into rear of unit, check polarizing key po-sition between contacts 3 and 4 for P155A1/P165A2 & between contactsA & B and T & V of P155A1/P165A2.2. Refer to Figure 2-11 to check correct position of polarizing key.D. Extraction of Contact from Molex Connector1. Slip the flat narrow blade of a Molex contact ejector tool, HT-1884 (P/N005-02012-0011), under the contact on the mating side of the connector.By turning the connector upside down one can see the blade slide intothe stop.2. When the ejector is slid into place, the retaining tab of the contact israised, allowing the contact to be removed by pulling moderately on thelead.3. Neither the contact or position is damaged by removing a contact; how-ever, the contact should be checked visually before reinstalling in con-nector to be certain that retaining tab "A" extends as shown (see Figure2-1).E. Coax ConnectorRefer to Figure 2-9 for the details for mounting the right angle coaxial BNC connector to the coax cable. Install the connector into the mounting rack.PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
Page 2-4 10542I02.ZIPRCDRev 2, Apr/2000BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM2.3.5 KX 155A/KX 165A INSTALLATION SEE PARAGRAPH 2.3.1 FOR COOLING REQUIREMENTS.A. Looking at the top of the unit, make sure the front lobe of the holddown device is in a vertical position.B. Slide the unit into the mounting rack until the front lobe touches the mounting rack.C. Insert a 3/32" Allen wrench through the hole in the front panel to engage the locking screw. Turn clockwise until the rear lobe engages the mounting rack. Continue turning until the unit is secure in the mounting rack. Do not overtighten.D. For removal, turn the locking screw counterclockwise using a 3/32" Allen wrench until the unit disengages from the mounting rack. Pull the unit out of the mounting rack by pulling on the metal tabs located behind the front panel on each side of the unit.2.3.6 ELECTRICAL INSTALLATION NOTES RETROFITDamage may occur in retrofit applications if the oldinstallation used COMM REMOTE TRANSFER orNAV REMOTE TRANSFER. If a COMREMOTETRANSFER wire was connected to pin P or R, itmust be moved to P155A/165A1-23. If a NAV RE-MOTE TRANSFER wire was connected to pin 13 or14, it must be removed. The KX 155A/KX 165Adoes not support NAV REMOTE TRANSFER. Fail-ure to remove the wire(s) will result in a direct shortto ground through the remote transfer switch to theNAV/COM circuit breaker when the switch ispressed. The circuit breaker and switch will bedamaged.EFIS 40/50The KX 165A may be interfaced to the Bendix/King EFIS 40/50 by using the KX 165A’s OBI CLOCK, OBI DATA, and OBI SYNC outputs for VOR bearing (RMI needle) and deviation, the COURSE DEVIATION +RIGHT and +LEFT for localizer deviation, and the GLIDESLOPE DEVI-ATION +UP and +DOWN for glideslope deviation. In order to use the KX 165A as a navigation source, the EFIS 40/50 must be configured for KNS 81 as VOR/LOC 1 or 2. Additionally, the KX 165A must be configured for Type II OBI data (see paragraph 3.1.4).CAUTIONCAUTIONPRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 2-5Rev 2, Apr/2000TRANSMIT INTERLOCKThe KX 155A includes a TRANSMIT INTERLOCK (P155A1-J/165A2-J) input which should be connected to the MIC KEY input(s) of the other COMM transceiver(s) in the aircraft. When this input is grounded, the KX 155A desensitizes its receiver by approximately 13 dB, reducing the like-lihood of its squelch breaking while another COMM in the aircraft is transmitting. It is highly rec-ommended to use this feature on all COMMs in the aircraft which include such an interlock feature. If TRANSMIT INTERLOCK is used in installations that employ a KX155A with a KMA26 (or other audio panel that pulls the MIC KEY line above 11 Volts), isolation diodes will need to be installed between P155A1, pin J and the MIC KEY line. Refer to Installation Bulletin 407 for details.AUDIO AMPLIFIERIf the KX 155A is installed as a “slide-in” replacement for a KX 155. The KX 155A’s audio amplifier functions will work just as the KX 155 did previously without rewiring any of the audio pins. Addi-tionally, there are many new audio system features within the KX 155A which provide maximum flexibility for use in a variety of audio/intercom configurations. The KX 155A provides audio am-plification for its VHF communication transceiver for both headphones and the cockpit speaker. In addition, up to three external sources of audio may be amplified and sent to the headphones and speaker. With proper external switching, the KX 155A can provide the microphone bias volt-age and amplification necessary for the implementation of a push-to-talk or a hot mic intercom. The KX 155A provides access to signals not commonly found on communication transceivers to allow full-featured installation with audio switching panels and audio isolation/amplifier panels.Three auxiliary audio inputs, AUX 1 AUDIO IN (P155A2-H), AUX 2 AUDIO IN (P155A2-F), and AUX 3 AUDIO IN (P155A2-4) are typically used to amplify audio from VOR/LOC, Marker Beacon, ADF, DME, Radio Altimeter Decision Height Alerters and other avionics audio sources. Any signal capable of driving a 500Ω or lower impedance load that is adjustable to less than 7 volts is accept-able. Each input has a low side pin, that is connected to ground inside the KX 155A.Should you have more than three audio sources, it is sometimes possible to successfully connect more than one source to a single pin. The sources will, in addition to driving the KX 155A input load, be driving the other source outputs as loads. Normally, this does not damage the source units but can cause lower signal levels resulting in less audio from these sources sharing that input pin. After installation, verify that turning the power off on each of the sources does not stop the audio from all the sources sharing the input.COMM AUDIO IN (P155A2-J) and INTERCOM MIC IN (P155A2-8) are inputs to the same ampli-fier used for the auxiliary audio inputs. The COMM AUDIO IN is reserved for the COMM AUDIO/SIDETONE/INTERCOM OUT and has the same gain as the auxiliary audio inputs. The INTER-COM MIC IN provides a MIC bias voltage output and should only be connected to aircraft micro-phones. Connection to other devices may result in damage to both the KX 155A and the other device.Connecting two microphones to the COMM MIC AUDIO or INTERCOM MIC IN at the same time may result in weak or distorted audio. Variations in microphones, even with identical manufactur-ers’ part numbers, can produce this problem when both are connected at the same time. Micro-phone isolation relays are recommended so that only one microphone is connected at one time.All five inputs described above are combined and amplified and output on the 500 OHMS AUDIO OUT (P155A2-D) and SUMMED AUDIO (OLD or NEW) OUT (P155A2-9 or P155A2-7). Both pins have identical signals but are at different voltage levels. The 500 OHMS AUDIO OUT will drive headphones directly. The SUMMED AUDIO (OLD or NEW) OUT are provided so that they may be input to the KX 155A’s internal 4Ω speaker amplifier. SUMMED AUDIO OLD OUT is utilized in retrofits of KX 155 installations, and SUMMED AUDIO NEW OUT is utilized for new installa-PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
Page 2-6 10542I02.ZIPRCDRev 2, Apr/2000BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEMtions. No signals, other than the five inputs, are output from the amplifier, thus allowing the install-er complete flexibility.SUMMED AUDIO IN (P155A2-10) is the input to the speaker amplifier. Only the signal applied to this input will be output on the 4 OHM AUDIO OUT (P155A2-1) output. The output will drive speakers of greater than 4Ω impedance, but since higher impedance speakers may expect higher voltages, they may not be as loud as 4Ω speakers. The speaker amplifier is muted (output is dis-abled) when the COMM transmitter is active (COMM MIC KEY input is low), and when the KX 155A intercom is keyed (INTERCOM MIC KEY input is low).If the 4 OHM AUDIO OUT output is to be used, different wiring configurations are required, de-pending on the KX 155A’s supply voltage, and whether or not the aircraft speaker is grounded on its low side.When a separate audio panel is used, neither the 500Ω nor 4Ω audio amplifiers in the KX 155A are connected. The KX 155A audio amplifiers do not need external loads applied to either their inputs or outputs when they are not used. NOTE: 500Ω audio output (P155A2 pins D & A) of 155-01647-0002 sheet 2 are not TSO’d at time of publication.AUDIO ALERTThe AUDIO ALERT output may be connected to a Sonalert or equivalent audio alerter, or to a pan-el-mounted annunciator lamp. At the time of this publication, the only function of AUDIO ALERT is to activate when the KX 155A/KX 165A countdown timer expires.2.4 POST INSTALLATION CHECK An operation performance flight test is recommended after the installation is completed to insure satisfactory performance of the equipment in its normal environment. Check all aircraft control movements to be sure no electrical cables interfere with their operation.To check the communications transceiver, maintain an altitude of at least 1500 feet and contact a ground station facility at a range of at least fifty nautical miles. Contact a ground station close in. Pull the volume control knob out to defeat the automatic squelch feature and listen for any unusual electrical noise which would reduce the COMM receiver sensitivity by increasing the squelch threshold. If possible, verify the communications capability on both the high and low end of the VHF COMM band.AS AN ADDED PRECAUTION BEFORE THEFLIGHT, CHECK THE ANTENNA. VSWRSHOULD BE CHECKED WITH AN IN-LINE TYPEWATTMETER INSERTED IN THE COAXIALTRANSMISSION LINE BETWEEN THE TRANS-CEIVER AND THE ANTENNA. ANY PROBLEMWITH THE ANTENNA INSTALLATION WILLMOST LIKELY BE SEEN AS A HIGH REFLECTEDPOWER. A VSWR OF 3:1 WILL RESULT IN A25% LOSS IN POWER.NOTECAUTIONPRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 2-7Rev 2, Apr/2000The brightness of the display can be set for the most pleasing intensity during low light level conditions via pilot configuration adjustment, see paragraph 3.1.3.To check the VOR/ILS system, select a VOR frequency within a forty nautical mile range. Listen to the VOR audio and insure that no electrical interference such as magneto noise is present. Check the tone identifier filter operation. Fly inbound or outbound on a selected VOR radial and check for proper LEFT-RIGHT and TO-FROM indications. Check the VOR accuracy.To check the localizer and glideslope functions, select an appropriate ILS frequency and fly an approach to the proper runway. Check for proper LEFT-RIGHT and UP-DOWN indications. The glideslope function will not operate for units that do not have the glideslope receiver. Check sec-tion 1 for unit part numbers that have glideslope receivers.PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
Page 2-8 10542I02.ZIPRCDRev 2, Apr/2000BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEMNOTEVOR Ground Station scalloping may be present.FIGURE 2-1 MOLEX TERMINALS AND TOOLSPRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 2-9Rev 2, Apr/20002.5 MOLEX TERMINAL INSTRUCTIONSThe Molex hand crimpers are available under P/N 071-06041-0000, or from Molex under P/N 6115.Holding the hand crimpers as shown, release the crimper’s ratchet pawl and open by squeezing tightly on the handles, and then releasing pressure.FIGURE 2-2 HAND CRIMPERClose crimpers until ratchet begins to engage. Then insert the terminal into the jaws from the back side. (See Figure 2-3 and 2-4) For 24 to 30 AWG wire, it will be necessary to start the crimp in jaw A and then complete it in jaw B. The terminal is in the correct position when the insulation tabs are flush with the outside face of the crimp jaws.JAW TERMINAL WIRE SIZE INSULATION RANGEA 030-01107-0030 18 TO 24 AWG .110 TO .055B 030-01107-0030 24 TO 30AWG .055 TO .030PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
Page 2-10 10542I02.ZIPRCDRev 2, Apr/2000BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEMFIGURE 2-3 CRIMP JAWSFIGURE 2-4 TERMINAL INSERTIONOnce the terminal is in the correct position, close the jaws gently until the terminal is held loosely in place. Push the wire stop down so that it rests snugly behind the contact portion of the terminal.Strip the wire insulation back 1/8 inch and insert the wire through the insulation tabs into the con-ductor tabs until the insulation hits the conductor jaw face or until the conductor touches the wire stop. Squeeze the handles until the crimp jaws close and the ratchet releases. Straighten the terminal if necessary, then release the plier grips and remove the crimped terminal.PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 2-11Rev 2, Apr/2000FIGURE 2-5 HAND CRIMPER INSERTIONIf too much or too little pressure is needed to release the crimper’s ratchet pawl at the end of the crimp stroke, the ratchet can be easily adjusted. A spanner wrench provided with the tool can be used to loosen the lock nut, and rotate the keyed stud clockwise for increased pressure and counter clockwise for decreased pressure. Once the desired pressure has been set, the lock nut must be tightened again. Newer models may have a screwdriver adjust-ment.FIGURE 2-6 CRIMPING PRESSURE ADJUSTMENTPRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
Page 2-12 10542I02.ZIPRCDRev 2, Apr/2000BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEMFigure 2-7 P155A1 & P165A1 CONNECTOR* Reserved pins in P155A11 COM DETECTED AUDIO A RNAV MODE2 COMM MIC AUDIO B INTERCOM MIC3 DME CLOCK C OBI DATA *4 OBI SYNC * D DME COMMON5 DME DATA E OBI CLOCK *6 COMM MIC KEY F RNAV/CHAN REQUEST7 NAV IF AGC H VOR/LOC COMPOSITE OUT8 LOC ENERGIZE J COMM IF AGC/ TRANSMIT INTERLOCK9 COM AUD/SIDETONE/INTERCOM/OUT K COM AUDIO/SIDETONE/INTERCOM LO10 NAV AUD OUT L NAV AUD LO11 SPARE M SPARE12 SWITCHED PWR OUT N SWITCHED PWR OUT13 28 VDC A/C PWR P 28 VDC A/C PWR14 RESERVED R RESERVED15 A/C GROUND S A/C GROUND16 SPARE T SPARE17 SPARE U SPARE18 SPARE V SPARE19 RESERVED W RESERVED20 RESERVED X RESERVED21 A/C GROUND Y RS 232 OUT22 AUDIO ALERT Z RS 232 IN23 COM REMOTE TRANSFER A CHANNEL REMOTE INCREMENT24 LIGHTING 14 VDC B RESERVED25 LIGHTING 28 VDC/LO C TESTPRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 2-13Rev 2, Apr/2000Figure 2-8 P155A2 P155A2A--------------- AUDIO LOB--------------- 4 OHM AUDIO OUT 14V LOC--------------- COMM MIC KEYD--------------- 500 OHM AUDIO OUTE--------------- RESERVEDF--------------- AUX 2 AUDIO INH--------------- AUX 1 AUDIO INJ--------------- COM AUDIO INK--------------- INTERCOM MIC KEYL--------------- A/C GROUNDM-------------- 4 OHM AUDIO BRIDGEDN--------------- SPAREP--------------- GS GROUNDR--------------- GS -FLAGS--------------- GS +UPT--------------- GS +DNU--------------- GS +FLAGV--------------- GS IF AGC1--------------- 4 OHM AUDIO OUT2--------------- COMM AUD OLD IN3--------------- RESERVED4--------------- AUX 3 AUDIO IN5--------------- AUDIO LO6--------------- AUDIO LO7--------------- SUMMED AUDIO NEW OUT8--------------- INTERCOM MIC IN9--------------- SUMMED AUDIO OLD OUT10-------------- SUMMED AUDIO IN11-------------- 4 OHM AUDIO OUT 28V LO12-------------- SPARE13-------------- GS GROUND14-------------- GS -FLAG15-------------- GS +UP16-------------- GS +DN17-------------- GS +FLAG18-------------- GS IF AGCPRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
Page 2-14 10542I02.ZIPRCDRev 2, Apr/2000BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEMFigure 2-9 P165A2P155A2A--------------- NAV -FLAGB--------------- NAV +FLAGC--------------- OBS RESOLVER DD--------------- SPAREE--------------- RESERVEDF--------------- NAV +TOH--------------- NAV +TOJ--------------- COURSE DEVIATION +LEFTK--------------- COURSE DEVIATION +LEFTL--------------- OBS RESOLVER GM-------------- A/C GROUNDN--------------- SPAREP--------------- A/C GROUNDR--------------- GS -FLAGS--------------- GS +UPT--------------- GS +DNU--------------- GS +FLAGV--------------- GS IF AGC1--------------- NAV -FLAG2--------------- OBS RESOLVER C3--------------- OBS RESOLVER F4--------------- SPARE5--------------- COURSE DEVIATION +RIGHT6--------------- COURSE DEVIATION +RIGHT7--------------- NAV +FLAG8--------------- NAV +FROM9--------------- NAV +FROM10-------------- OBS RESOLVER E11-------------- OBS RESOLVER H12-------------- SPARE13-------------- GS GROUND14-------------- GS -FLAG15-------------- GS +UP16-------------- GS +DN17-------------- GS +FLAG18-------------- GS IF AGCPRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
KX 155A/165ACOMM/NAV SYSTEMPage 2-15BENDIX/KING10542I02.ZIPRCDRev. 2, Apr/2000FIGURE 2-9 ANTENNA CABLE ASSEMBLY(P/N 030-00101-0002, R-9)PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
KX 155A/165ACOMM/NAV SYSTEMPage 2-17BENDIX/KING10542I02.ZIPRCDRev. 2, Apr/2000FIGURE 2-10 KX 155A/KX 165A OUTLINE AND MOUNTING DRAWING(Dwg. No 155-01661-0000, Rev AC)PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
KX 155A/165ACOMM/NAV SYSTEMPage 2-19BENDIX/KING10542I02.ZIPRCDRev. 2, Apr/2000FIGURE 2-11 KX 155A/165A INSTALLATION ASSEMBLY DRAWING(Dwg No 300-09247-0000, Rev AA)(Sheet 1 of 2)PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
KX 155A/165ACOMM/NAV SYSTEMPage 2-21BENDIX/KING10542I02.ZIPRCDRev. 2, Apr/2000FIGURE 2-11 KX 155A/165A INSTALLATION ASSEMBLY DRAWING(Dwg No 300-09247-0000, Rev AA)(Sheet 2 of 2)PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
KX 155A/165ACOMM/NAV SYSTEMPage 2-23BENDIX/KING10542I02.ZIPRCDRev. 2, Apr/2000FIGURE 2-12 KX 155A/165A NAV INDICATOR INTERFACE(Sheet 1 of 2) (Dwg No 155-01647-0000, Rev AB)PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
KX 155A/165ACOMM/NAV SYSTEMPage 2-25BENDIX/KING10542I02.ZIPRCDRev. 2, Apr/2000FIGURE 2-12 KX 155A/165A NAV INDICATOR INTERFACE(Sheet 2 of 2) (Dwg No 155-01647-0000, Rev AB)PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
KX 155A/165ACOMM/NAV SYSTEMPage 2-27BENDIX/KING10542I02.ZIPRCDRev. 2, Apr/2000FIGURE 2-13 KX 155A/165A DME/RNAV INTERFACE(Dwg No 155-01647-0001, Rev 0)(Sheet 1 of 2)PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
KX 155A/165ACOMM/NAV SYSTEMPage 2-29BENDIX/KING10542I02.ZIPRCDRev. 2, Apr/2000FIGURE 2-13 KX 155A/165A DME/RNAV INTERFACE(Dwg No 155-01647-0001, Rev 0)(Sheet 2 of 2)PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
KX 155A/165ACOMM/NAV SYSTEMPage 2-31BENDIX/KING10542I02.ZIPRCDRev. 2, Apr/2000FIGURE 2-14 KX 155A/165A AUDIO INTERFACE(Dwg No 155-01647-0002, Rev AB)(Sheet 1 of 4)PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
KX 155A/165ACOMM/NAV SYSTEMPage 2-33BENDIX/KING10542I02.ZIPRCDRev. 2, Apr/2000FIGURE 2-14 KX155A/165A AUDIO INTERFACE(Dwg No 155-01647-0002, Rev AB)(Sheet 2 of 4)PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
KX 155A/165ACOMM/NAV SYSTEMPage 2-35BENDIX/KING10542I02.ZIPRCDRev. 2, Apr/2000FIGURE 2-14 KX 155A/165A AUDIO INTERFACE(Dwg No 155-01647-0002, Rev AB)(Sheet 3 of 4)PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
KX 155A/165ACOMM/NAV SYSTEMPage 2-37BENDIX/KING10542I02.ZIPRCDRev. 2, Apr/2000FIGURE 2-14 KX 155A/165A AUDIO INTERFACE(Dwg No 155-01647-0002, Rev AB)(Sheet 4 of 4)PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
KX 155A/165ACOMM/NAV SYSTEMPage 2-39BENDIX/KING10542I02.ZIPRCDRev. 2, Apr/2000FIGURE 2-15 LIGHTING, ALERTING AND REMOTE INTERFACE(Dwg No 155-01647-0003, Rev 0) pgPRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
KX 155A/165ACOMM/NAV SYSTEMPage 2-41BENDIX/KING10542I02.ZIPRCDRev. 2, Apr/2000FIGURE 2-16 MISCELLANEOUS INTERFACE(Dwg No 155-01647-0005, Rev AA) PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 3-1Rev 2, Apr/2000SECTION IIIOPERATION3.1 GENERAL All controls required to operate the KX 155A/165A are located on the unit front panel. (See Figure 3-1)FIGURE 3-1 KX 155A/165A CONTROL FUNCTION3.1.1 COMM TRANSCEIVERRotate the VOL knob clockwise from the OFF position. Pull the VOL knob out and adjust for de-sired listening level. Push the VOL knob back in to actuate the automatic squelch.The left portion of the digital display readout is allocated for COMM ACTIVE, and COMM STAND-BY frequencies with a “T” between them to indicate TRANSMIT and an “R” to indicate RECEIVE modes of operation.Select the desired operating frequency in the standby display by rotating the Frequency Select Knobs either clockwise or counter-clockwise. A clockwise rotation will increment the previous fre-quency while a counterclockwise rotation will decrement the previous frequency.Frequency Selection for 25 kHz radio versions:This paragraph applies to KX 155A part numbers 069-01032-0101/0201 and KX 165A part num-ber 069-01033-0101. The outer knob will change the MHz portion of the standby display. At one PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
Page 3-2 10542I02.ZIPRCDRev 2, Apr/2000BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEMband-edge (118 or 136 MHz) the following 1 MHz change will wrap around to the other band-edge. The inner knob will change the kHz portion of the standby display. It will change in steps of 50 kHz when the knob is pushed in, and 25 kHz when the knob is pulled out. The frequency wrap around at the edge of the band is also utilized when incrementing or decrementing the kHz portion of the standby display.Frequency Selection for 8.33 kHz radio versions:This paragraph applies to KX 165A part number 069-01033-0201. The outer knob will change the MHz portion of the standby display. At one band-edge (118 or 136 MHz) the following 1 MHz change will wrap around to the other band-edge. The inner knob will change the kHz portion of the standby display. With the inner knob pushed in, the frequency will increment or decrement in 25 kHz steps as the inner knob is rotated clockwise or counterclockwise. The COMM receiver is operating with conventional (25 kHz) selectivity when the inner knob is pushed in. When the inner knob is pulled out the receiver becomes compatible with the new 8.33 kHz airspace. In this case the displayed frequency doesn’t always correspond directly to the actual operating frequency. In this case clockwise (counterclockwise) rotation of the inner knob increments (decrements) the dig-its to the right of the decimal point in the following fashion.Displayed Frequency Operating Frequency Receiver Selectivityxxx.000 xxx.0000 MHz 25 kHzxxx.005 xxx.0000 MHz 8.33 kHzxxx.010 xxx.0083 MHz 8.33 kHzxxx.015 xxx.0167 MHz 8.33 kHzxxx.020 xxx.0250 MHz 25 kHzxxx.030 xxx.0250 MHz 8.33 kHzxxx.035 xxx.0333 MHz 8.33 kHzxxx.040 xxx.0417 MHz 8.33 kHzxxx.050 xxx.0500 MHz 25 kHzxxx.055 xxx.0500 MHz 8.33 kHzxxx.060 xxx.0583 MHz 8.33 kHzxxx.065 xxx.0667 MHz 8.33 kHzxxx.070 xxx.0750 MHz 25 kHzxxx.080 xxx.0750 MHz 8.33 kHzxxx.085 xxx.0833 MHz 8.33 kHzxxx.090 xxx.0917 MHz 8.33 kHzThis pattern repeats for all the 100 kHz increments. (It should be noted that the pilot does not need to know the operating frequency or selectivity associated with each displayed frequency. Flying charts and/or ATC communications are designed to relate in terms of the displayed fre-quency only.)To tune the radio to the desired operating frequency, the desired frequency must be entered into the standby display and then the transfer button must be pushed. This will trade the contents of the active and standby displays. The operating frequency can also be entered by accessing the ACTIVE ENTRY (direct tune) mode which is done by pushing and holding the COMM TRANSFER button for 2 or more seconds. In the direct tune mode, only the active part of the display is visible. The desired frequency can be directly entered into the display. Push the COMM TRANSFER but-ton again to return to the active/standby display.PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 3-3Rev 2, Apr/2000The transceiver is always tuned to the frequency appearing in the ACTIVE display. It is therefore possible to have two different frequencies stored in the ACTIVE and STANDBY displays and to change back and forth between them at the simple push of the transfer button.During the transmit mode of operation, a “T” will appear between the ACTIVE and STANDBY dis-plays. An “R” will appear between the ACTIVE and STANDBY displays if a detected signal is strong enough to open the squelch, signifying that the transceiver is in the receive mode of oper-ation.A non-volatile memory stores the comm ACTIVE and STANDBY frequencies on power down. When the unit is turned on again, the COMM ACTIVE and STANDBY windows will display the same ACTIVE and STANDBY frequencies that were displayed before power down.The KX 155A/165A also has provision to program 32 channels. Pressing the CHAN button for 2 or more seconds will cause the unit to enter the channel program mode. Upon entering the chan-nel program mode,“PG” is displayed next to the channel number and the channel number will flash indicating that it can be programmed. The desired channel can be selected by turning the comm kHz knob. The channel frequency can be entered by pushing the COMM TRANSFER button which will cause the standby frequency to flash. The comm frequency knobs are then used to en-ter the desired frequency. If dashes (displayed when rotating the outer knob between 136 MHz and 118 MHz) are entered instead of a frequency, the corresponding channel is skipped in chan-nel selection mode. Additional channels may be programmed by pressing the COMM TRANS-FER and using the same procedure. To exit the program mode and save the channel information, momentarily push the CHAN button. This will cause the unit to return to the previous frequency entry mode. The unit will also exit the channel program mode if there is no button or knob activity for 20 seconds.The channel selection mode can then be entered by momentarily pushing CHAN button. “CH” is displayed next to the last used channel number. The comm frequency knobs can be used to se-lect the desired channel. The unit will automatically default to the previous mode if no channel is selected within 2 seconds after entering the channel selection mode.The unit is placed in the transmit mode by depressing the MIC KEY button. The unit has a stuck microphone alert feature. If the microphone is keyed continuously for greater than 33 seconds, the transmitter stops transmitting and the active Comm frequency flashes to alert the pilot of the stuck microphone condition.3.1.2 NAV RECEIVER The right portion of the display is allocated to NAV receiver information. The frequency channeling is similar to the COMM when operating in the frequency mode (Figure 3-1). The NAV increment/decrement knobs are located on the right hand side of the front panel. The outer knob operates in 1 MHz steps and increments/decrements the STANDBY frequency display.The inner knob operates in 50 kHz steps. The NAV receiver’s lower and upper frequency limits are 108.00 MHz and 117.95 MHz. Exceeding the upper limit of frequency band will automatically return to the lower limit and vice versa.Depressing the NAV frequency transfer button for 2 seconds or more will cause the display to go in to the ACTIVE ENTRY mode. Only the ACTIVE frequency will be displayed and it can be di-rectly changed by using the NAV inc/dec knobs. The display will return to the ACTIVE/STANDBY mode when the NAV frequency transfer button is pushed.Depressing the mode button will cause the NAV display to go from the ACTIVE/STANDBY format to the ACTIVE/CDI (Course Deviation Indicator) format as shown below in Figure 3-2. In the CDI mode, the increment/decrement knob (pushed in) channels the ACTIVE frequency window and depressing the frequency transfer button will cause the ACTIVE frequency to be placed in blind storage and the STANDBY frequency (in blind storage) to be displayed in the ACTIVE window dis-PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
Page 3-4 10542I02.ZIPRCDRev 2, Apr/2000BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEMplay. When the ACTIVE window is tuned to a VOR frequency, the standby frequency area is re-placed by a three digit OBS (Omni Bearing Selector) display. The desired OBS course can be selected by pulling out the inner NAV frequency knob and turning it. This OBS display is indepen-dent of any OBS course selected on an external CDI or HSI. An “OBS” in the middle of the NAV display will flash while the inner NAV frequency knob is pulled out. The CDI is displayed on the line below the frequency/OBS. When the ACTIVE window is tuned to a localizer frequency, the standby frequency area is replaced by “LOC” Figure 3-3. Illustrations of the display are shown below.FIGURE 3-2 NAV DISPLAY; ACTIVE VOR FREQUENCY/CDI FORMATPRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 3-5Rev 2, Apr/2000FIGURE 3-3 NAV DISPLAY; ACTIVE LOCALIZER FREQUENCY/CDI FORMATWhen the received signal is too weak to ensure accuracy the display will “flag”. See Figure 3-4.FIGURE 3-4 VOR FLAG DISPLAYDepressing the mode button will cause the NAV display to go from the ACTIVE/CDI format to the ACTIVE/BEARING format. In the BEARING mode, the increment/decrement knob channels the ACTIVE frequency window and depressing the frequency transfer button will cause the ACTIVE frequency to be placed in blind storage and the STANDBY frequency (in blind storage) to be dis-played in the ACTIVE window display. In bearing mode of operation, the right hand window of NAV display shows the bearing TO the station. Figure 3-5 below illustrates the NAV side of the display in this mode:FIGURE 3-5 VOR MODE; BEARING TO FUNCTIONWhen a too weak or invalid VOR signal is received the display flags as shown in Figure 3-6.PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
Page 3-6 10542I02.ZIPRCDRev 2, Apr/2000BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEMFIGURE 3-6 VOR MODE; ACTIVE/BEARING, FLAG DISPLAYAnother push of the mode button will cause the NAV display to go from the ACTIVE/BEARING format to the ACTIVE/RADIAL format as shown in Figure 3-7. In the RADIAL mode, the incre-ment/decrement knob channels the ACTIVE frequency window and depressing the frequency transfer button will cause the ACTIVE frequency to be placed in blind storage and the STANDBY frequency (in blind storage) to be displayed in the ACTIVE window display. In radial mode of op-eration, the right hand window of NAV display shows the radial FROM the station. The picture below illustrates the NAV side of the display in this mode:FIGURE 3-7 VOR MODE; RADIAL FROM FUNCTIONWhen a too weak or invalid VOR signal is received the display flags as shown in Figure 3-8.FIGURE 3-8 VOR MODE; ACTIVE/RADIAL, FLAG DISPLAYPRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 3-7Rev 2, Apr/2000Another push of the mode button will cause the unit to go into the TIMER mode. See Figure 3-9. When the unit is turned on the elapsed timer begins counting upwards from zero. The timer can be stopped and reset to zero by pushing the NAV frequency transfer button for 2 seconds or more causing the ET on the display to flash. In this state the timer can be set as a countdown timer or the elapsed timer can be restarted. The countdown timer is set by using the NAV inc/dec knobs to set the desired time and then pushing the NAV frequency transfer button to start the timer. The outer knob selects minutes, the inner knob in the “in “ position selects ten second intervals, and the inner knob in the “out” position selects individual seconds. After the countdown timer reaches zero, the counter will begin to count upwards indefinitely while flashing for the first 15 seconds. Or the elapsed timer can also be reset to zero and started again after it has been stopped and reset to zero by pushing the NAV frequency transfer button. The Audio Alert pin ( pin 22 of P155A1/P165A1 ) goes low when the countdown timer goes to zero and drives an external alarm ( buyer supplied ). The pin is capable of sinking 250 mA at a voltage of not more than 1 VDC.FIGURE 3-9 TIMER MODEThe NAV ACTIVE and STANDBY frequencies are stored in the memory on power down and return on power up.When the smaller increment/decrement knob is pushed in, depressing the NAV TRANSFER but-ton will interchange the ACTIVE and STANDBY frequencies. The NAV IDENT knob is active in the pulled out position so that both voice and ident can be heard. When this knob is pushed in, the ident tone is attenuated. The volume of voice/ident can be adjusted by turning this knob.3.1.3 PILOT CONFIGURATIONThis mode can be accessed by pressing and holding the Nav Mode Button for more than 2 sec-onds and then pressing the Nav Frequency Transfer Button for an additional 2 seconds, while con-tinuing to hold the Nav Mode Button. When the Pilot Config Mode is entered the unit will show the “SWRV” mnemonic which is the unit software revision level. Adjustment pages can be accessed by MODE button presses. The pilot may adjust two parameters in the pilot configuration, the display minimum brightness and sidetone volume level. See Table 3-1.Minimum Brightness (BRIM) will have a range of 0 - 255. The dimmest is 0 and the brightest is 255. The brightness can be increased by rotating the inner and outer NAV Frequency Select knobs clockwise. Rotate the knobs counterclockwise to decrease the brightness and clockwise to increase the brightness. The inner knob will change the brightness in increments of 1 and the out-er knob will change it in increments of 10.PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
Page 3-8 10542I02.ZIPRCDRev 2, Apr/2000BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEMSidetone volume level is adjusted when SIDE is displayed. Values from 0 - 255 may be selected with 0 being least volume, 255 being the greatest. Table 3-1 Pilot ConfigurationSubsequent presses of the MODE button sequences through SWRV, BRIM, SIDE, and then back to SWRV.Momentarily pressing the Nav Transfer Button exits Pilot configuration mode. The Nav returns to its pre-Pilot Config state with the new brightness and sidetone levels stored in non-volatile mem-ory. 3.1.4 INSTALLATION MODEThe installation mode should only be used by a qualified avionics technician. Installation configuration adjusts several unit parameters in order to conform the unit to a given installation. The following adjustments will be accessible from the front panel in order to facilitate unit installa-tion: Table 3-2 shows the page sequence.Table 3-2 Installation Mode PagesAdjustment Mnemonic Min Level Max LevelSoftware Revision Number SWRV -- --Minimum Display Brightness BRIM 0 255Sidetone Level SIDE 0 255Adjustment Mnemonic Min Level Max Level CommentSoftware Revision SWRV N/A N/AIntercom INTC 0 255Comm S/N Squelch SNSQ 0 255Comm S/N Squelch (8.33) SNS8 0 255 KX 165A onlyComQuickTune CQTN 0 4NavQuickTune NQTN 0 4VOR/LOC Composite Level COMP 0 255Photocell Offset PHOF -99 99VOR D Bar Time Constant VBAR 1 10LOC D Bar Time Constant LBAR 0.6 3VOR/LOC Converter Centering OffsetVLCO -64 64 KX 165A onlyVOR/LOC Converter Course Width VLCW 0 255 KX 165A onlyResolver Zero Point Z300 0 1 KX 165A onlyPRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 3-9Rev 2, Apr/2000The installation configuration mode will be accessed by the following sequence. The unit is turned on while simultaneously pressing Communication Channel Button for 8 to 12 seconds. The button shall be released within 8 to 12 seconds. Within 0.2 to 2 seconds following its release, the button must be momentarily depressed. Following this sequence, the unit will automatically enter its in-stallation mode. Within 0.5 seconds of reaching installation mode, the display will annunciate “INST” in the 4 character alphanumeric position on the NAV side of the display; all other display segments are off. A page can be accessed once in the installation configuration mode by pushing the Comm Mode Button one or more times. Each button push will cause the display to advance to the next page; the first page shall follow the last page.3.1.4.1 Intercom Mic Gain adjustment (INTC)Intercom Mic Gain adjustment (INTC) has a range of 0 to 255. The lowest volume is 0, and the highest volume is 255.3.1.4.2 Com S/N Squelch (SNSQ) Com S/N Squelch (SNSQ) adjustment has a range of 0 to 255. In the range of settings from 0 to 63, it changes the Squelch setting approximately 1 dB/step. Lowering the setting causes the squelch to open at higher R.F. power levels. Raising the setting causes the squelch to open at lower R.F. power levels. Adjustments to SNSQ do not take affect until the radio’s power is cycled.External OBS Resolver 300/0 DegreeR300 or R000Auto KX 165A onlyExternal OBS Resolver 30/90 DegreeR030 or R090Auto KX 165A onlyExternal OBS Resolver 120/180 DegreeR120 orR180Auto KX 165A onlyExternal OBS Resolver 210/270 DegreeR210 orR270Auto KX 165A onlyOBI Type I or II selection OBI 1 2 KX 165A onlyGlide Slope Centering Offset GSCO -99 99Glide Slope Course Width GSCW 0 255Program Secure PSEC n/a n/aFault 01 FALT n/a n/aFault 02 FALT n/a n/aFault 03 FALT n/a n/aFault 04 FALT n/a n/aFault 05 FALT n/a n/aFault 06 FALT n/a n/aFault 07 FALT n/a n/aFault 08 FALT n/a n/aFault 09 FALT n/a n/aFault 10 FALT n/a n/aPRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
Page 3-10 10542I02.ZIPRCDRev 2, Apr/2000BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM3.1.4.3 The SNS8 COMM S/N SquelchThe SNS8 COMM S/N Squelch setting behaves like the SNSQ setting but only applies to the 8.33 channel settings. Lowering the values for SNSQ and SNS8 will require a stronger signal to be present before audio will be heard.3.1.4.4 Comm Quick Tune (CQTN) and Nav Quick Tune (NQTN) Comm Quick Tune (CQTN) and Nav Quick Tune (NQTN) are system numbers that will allow an external device to update the standby frequencies for the Comm and Nav. The external device must use the same system number as the number set here.3.1.4.5 VOR/LOC Composite Level (COMP)VOR/LOC Composite Level (COMP) has a range of 0 to 255. The Level is factory set, and should not need adjustment. A setting of 0 produces a minimum VOR/LOC level, a setting of 255 pro-duces a maximum level. The VOR/LOC Composite Level may be adjusted to interface with an external converter/indicator. Increasing the Composite Level will increase an indicator’s needle deflection. Decreasing the Composite Level will reduce an indicator’s needle deflection. Adjust-ments to COMP do not take affect until the radio’s power is cycled. A description of this procedure is included in the Maintenance Manual.3.1.4.6 Photocell Offset (PHOF)Photocell Offset (PHOF) has a range of -99 to 99. A setting of -99 increases the brightness of the display, a setting of 99 decreases the brightness of the display.3.1.4.7 VOR Deviation Bar Response Time (VBAR)The following, Table 3-3 describes the correspondence between the front panel display and VOR D bar response times. Response time is defined as time required to reach 67% of the final value. Note: Any departure from the factory default value of VBAR should only be made after careful consideration of its affect on the aircraft certification, especially where a flight control system is involved.PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 3-11Rev 2, Apr/2000Table 3-3 VOR Deviation Bar Response Time 3.1.4.8 Localizer Deviation Bar Time Constant (LBAR)The following, Table 3-4 and Figure 3-11 describe the correspondence between the front panel display and localizer D bar time constant. In this case, the “dot” shall be used to show the tenths of seconds. Response time is defined as time required to reach 67% of the final value. NOTE: Any departure from the factory default value of LBAR should only be made after careful consideration of its affect on the aircraft certification, expecially when a flight control system is involved.3.1.4.9 VOR/LOC Converter Centering Offset (VLCO)VOR/LOC Converter Centering Offset (VLCO) has a range of -64 to 64. A setting below 0 moves the indicator’s needle to the left (increases the voltage?), a setting above 0 moves the indicator’s needle to the right (decreases the voltage?). An external RF signal is not required to make this adjustment. The radio automatically outputs a centering converter voltage that can be used when adjusting to interface between the radio’s internal converter and an external indicator.3.1.4.10 VOR/LOC Converter Course Width (VLCW)VOR/LOC Converter Course Width (VLCW) has a range of 0 to 255. A setting of 0 will result in a minumum amount of needle deflection to the left. A setting of 255 will result in a maximum amount of needle deflection to the left. An external RF signel is not required to make this adjustment. The radio automatically outputs a deflection converter voltage that can be used when adjusting the in-terface between the radio’s internal converter and an external indicator.3.1.4.11 Resolver Zero Point (Z300)Resolver Zero Point (Z300) can have the value of 0 or 1. A setting of 1 indicates that the external resolver is aligned at 300 degrees, and the next four pages will be labeled R300, R030, R120 and R210. A setting of 0 indicates that the external resolver is aligned at 0 degrees and the next four pages will be labeled R000, R090, R180 and R270. If this setting is incorrect the next four pages External OBS Resolver Degree Settings will not successfully calibrate.Front PanelValue Time Con-stant (sec)11223344556677889910 10PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
Page 3-12 10542I02.ZIPRCDRev 2, Apr/2000BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM3.1.4.12 External OBS Resolver Degree Settings (R300, R030, R120, R210; or R000, R090, R180, R270)Supply a standard VOR signal to the NAV antenna port at 113.5 MHz. Bearing is not important. This is necessary to generate a 30 Hz reference signal output by the internal converter. Adjust the external resolver to the compass point indicated by the last three digits of the mnemonic, for example on the “R030” page set the external resolver to 30 degrees. When adjusting the external resolver it is best to go slightly past, and then back up to eliminate some of the mechanical back-lash.After External Resolver is set press the NAV Transfer Button. The display will flash while the re-solver offset is being calibrated. When the display stops flashing, a number less than 99 should appear. The number represents the alignment error in 0.1-degree units. Repeat for each of the four compass points. The following figure 3-10 shows a 0.4-degree error after calibration at the 300-degree compass point.Figure 3-10If “99” is displayed the calibration was unsuccessfull. If any of the four compass pages are unsuc-cessful, check for presence of a 3 Vp-p 30Hz (nominal) sine wave at Rotor C. If a 3 Vp-p 30 Hz sine wave is present at Rotor C, variable amplitude 30Hz sine waves should be present at Stator D and Stator F. Amplitude of these two signals should vary with resolver compass settings. If all of these conditions are present and alignment shows “99”, the indicator or receiver may require service.3.1.4.13 OBI Type I or II Selection (OBI)OBI Type I or II Selection (OBI) should be set for 1 for interfacing to a Type I OBI and set to 2 to interface to a Type II OBI.3.1.4.14 GS Converter Centering Offset (GSCO)GS Converter Centering Offset (GSCO) has a range of -64 to 64. A setting below 0 raises the indicator needle (increases the voltage), a setting above 0 lowers the indicator needle (decreases the voltage). An external RF GS signal is not required to make this adjustment. The radio auto-matically outputs a centering converter voltage that can be used when adjusting the interface be-tween the radio’s internal GS converter and an external indicator. The GS Converter Centering Offset should be adjusted so that the external indicator is set at zero (0 ddm, 0 µA).113.5 4 R300PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 3-13Rev 2, Apr/20003.1.4.15 GS Converter Course Width (GSCW)GS Converter Course Width (GSCW) has a range of 0 to 255. A setting of 0 will result in a mini-mum indicator displayed half deflection. A setting of 255 will result in a maximum indicator dis-played half deflection. An external RF GS signal is not required to make this adjustment. The radio automatically outputs a half deflection converter voltage that can be used when adjusting the interface between the radio’s internal GS converter and an external indicator. The GS Converter Course Width should be adjusted so that the external indicator is set at half deflection (.091 ddm, 78 µA).Table 3-4 Localizer Deviation Bar Time ConstantFIGURE 3-11 VOR DEVIATION BAR RESPONSE TIME3.1.4.16 Program SecureThe program secure mode allows the installer to lock or unlock an already defined frequency to a specific channel number, and will prohibit the operator from programming changes to the chan-nel memories from the front of the unit during normal operation. All other functions shall remain unchanged during normal operation. The lock state can be toggled rotating the Nav Inner or Outer Frequency Selection Knobs. The Nav Mode Button is used to scroll the list of channels. If the frequency is locked, the upper left segment of the nav display will display an “L”, otherwise a “U” will be displayed as shown in Figure 3-12.Front PanelValue Time Con-stant (sec)0.5 0.61.0 1.01.5 1.52.0 2.02.5 2.53.0 3.0PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
Page 3-14 10542I02.ZIPRCDRev 2, Apr/2000BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEMFIGURE 3-12 FREQUENCY LOCK AND UNLOCK STATES3.1.4.17 Fault ReportingThis section on fault reporting is here for reference only. The KX155A fault codes are primarily for the benefit of AlliedSignal design engineering personnel. The meaning of each fault code is not published here or in the KX155A Maintenance Manual since they contain no user or product ser-vice benefit. Faults that occur in the unit are recorded in non-volatile memory, and are part of the installation mode. Only the last ten faults are recorded, and are shown one fault per page. Page (1) shows the most recent fault. Page (2) shows the next most recent fault and so forth. If less than 10 faults exist, then the fields for the time and fault code are blank. The fault type which is in the active frequency area shows the type of fault that has occurred, and the fault code shows where in the software the fault occurred. Figure 3-13 and Table 3-5 show the display while in fault reporting: Figure 3-13 TYPICAL FAULT DISPLAYPRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 3-15Rev 2, Apr/2000Table 3-5 Fault DisplayIf no faults exist, the following display is used for empty fault pages as shown in Figure 3-14.Figure 3-14 FAULT DISPLAY, NO FAULTThe fault codes and times can be reset to zero (blank) by simultaneously depressing the comm transfer and nav transfer buttons for 5 or more seconds.3.2 KI 202/203/204, KI 206/208/209/208A/209A INDICATOR CONTROLS AND FUNCTIONS 3.2.1 VOR OPERATION Channel the NAV Receiver to the desired VOR and monitor the audio to positively identify the sta-tion. To intercept a selected VOR radial, turn the OBS to set the desired radial under the lubber line. The left-right needle will now deflect in the direction of the desired radial. Flying toward nee-dle deflection will bring the aircraft to the desired radial.To fly inbound toward the station, turn the OBS to center the left-right needle while the To-From is indicating TO. Read the bearing under the lubber line and fly that magnetic course. When the aircraft passes over the station, the To-From will momentarily disappear and then reappear as FROM. This indicates the aircraft is outbound from the station.3.2.2 LOC OPERATION Localizer circuitry is energized when the NAV Receiver is channeled to an ILS frequency. The VOR/LOC flag will be out of view when the signal is usable. Corrections for approach should be made toward the needle, as in VOR, but due to increased sensitivity, corrections are smaller. When flying inbound on a back course, deflection of the needle will be reversed.Fault PageNumber:Use the 2 most significant digits of the Comm active frequency dis-play.Fault Time: Use all digits of the comm standby frequency display with a maximum of 199999 hoursFALT: Annunciates a fault; alphanumeric portion of the nav display.Fault Type: Use 3 least significant digits of the nav active frequency display.Fault Code The two most significant digits identify the module in which the error is detected. The two least significant digits identify the error number for the module error. PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
Page 3-16 10542I02.ZIPRCDRev 2, Apr/2000BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM3.2.3 GLIDESLOPE OPERATION Glideslope operation is much the same as the Localizer just discussed. An Up deflection of the needle indicates the aircraft is below desired glidepath. The pilot must fly toward the needle for correction. A warning flag is provided to indicate usable signal conditions.3.2.4 UNIT CONTROL FUNCTIONS The following figure (Figure 3-15) displays the control functions for the KI 204/206/209. The KI 202/203/208 differs in not having a glideslope needle or flag. The KI 207 differs in not having an OBS or Azimuth card.FIGURE 3-15 KI 202/203/204/206/207/208/209/208A/209A TYPICAL INDICATOR MARKINGS3.3 KI 525A INDICATOR CONTROLS AND FUNCTIONS 3.3.1 VOR/LOC AND GLIDESLOPE OPERATION Set the navigation receiver to the desired VOR/LOC station and rotate the course select knob to adjust the selected course pointer to the desired course radial. When a usable navigation signal is received by the KI 525A the NAV warning flag will disappear from view.For an ILS approach, tune the navigation receiver to the desired frequency.The glideslope pointer will deflect into view after a 2 to 10 second delay if a usable glideslope sig-nal is received. The glideslope pointer indicates the relative position of the glideslope path with respect to the aircraft.For LOC operation, tune the navigation receiver to the desired frequency and set the pointer to the selected inbound localizer course. The position of the deviation bar with respect to the sym-PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page 3-17Rev 2, Apr/2000bolic aircraft indicates the relative position of the selected course. For backcourse operation, set the course pointer to the inbound localizer front course. The deviation bar position relative to the symbolic aircraft then represents the position of the backcourse with respect to the aircraft. Figure 3-16 displays the control functions for the KI 525.FIGURE 3-16 KI 525A INDICATOR AND CONTROLS3.4 KI 229 RMI OPERATION The KNI 229 Radio Magnetic Indicator provides bearing information to both ADF and VOR sta-tions by means of two pointers, each of which is read against the compass card. The servo drive compass card displays heading information derived from ARINC type X, Y, Z, compass headings. The double pointer is dedicated solely to a ADF DC SIN/COS source. The single pointer is as-signed to VOR information.NOTEThe single pointer can be switched between VOR and ADF by means of an external switch as ex-plained in the installation manual of the KNI 229.3.5 OTHER INDICATORSRefer to respective installation manuals for operation instructions of other indicators.PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
10542I02.ZIPRCD Page EN-72Rev 2, Dec/1999ENVIRONMENTAL QUALIFICATION APPENDIXRTCA DO-160CENVIROMENTAL QUALIFICATIONFORMSPRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
Page EN-73 10542I02.ZIPRCDRev 2, Apr/2000BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEMPRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEM10542I02.ZIPRCD Page EN-74Rev 2, Apr/2000PRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE
Page EN-75 10542I02.ZIPRCDRev 2, Apr/2000BENDIX/KINGKX 155A/165ACOMM/NAV SYSTEMPRELIMINARY - SUBJECT TO CHANGE WITHOUT NOTICE

Navigation menu