Honeywell 8DLLMD500 Lyric Smart Peripheral - Motion Detector User Manual Quick Install Manual

Honeywell International Inc. Lyric Smart Peripheral - Motion Detector Quick Install Manual

Quick Install Manual

This wireless passive infrared motion sensor is intended for use with Honeywell controls that support SiX™ series devices. FC: This wireless passive infrared motion sensor is intended for use with Honeywell controls that support SiX™ series devices. SP: This wireless passive infrared motion sensor is intended for use with Honeywell controls that support SiX™ series devices. PA: This wireless passive infrared motion sensor is intended for use with Honeywell controls that support SiX™ series devices. Motion Sensor Open / Open / Open NOTE: Once enrolled, the sensor cannot be used with another system until it is removed from the current controller. See the controller’s instructions. FC: NOTE: Once enrolled, the sensor cannot be used with another system until it is removed from the current controller. See the controller’s instructions. SP: NOTE: Once enrolled, the sensor cannot be used with another system until it is removed from the current controller. See the controller’s instructions. PA: Once enrolled, the sensor cannot be used with another system until it is removed from the current controller. See the controller’s instructions. Enroll / Enroll / Enroll / Enroll Mounting Locations / Mounting Locations / Mounting Locations / Mounting Locations NOTE: After enrolling and before mounting permanently, conduct Go/No Go tests (see controller’s instructions) to verify adequate signal strength. Adjust the device location and orientation as necessary. FC: Note: After enrolling and before mounting permanently, conduct Go/No Go tests (see controller’s instructions) to verify adequate signal strength. Adjust the device location and orientation as necessary. SP: Note: After enrolling and before mounting permanently, conduct Go/No Go tests (see controller’s instructions) to verify adequate signal strength. Adjust the device location and orientation as necessary. PA: Note: After enrolling and before mounting permanently, conduct Go/No Go tests (see controller’s instructions) to verify adequate signal strength. Adjust the device location and orientation as necessary. Mounting Options / Mounting Options / Mounting Options / Mounting Options PLEASE SEE BOTTOM OF PAGE FOR FCC/IC AGENCY STATEMENTS
 2014 Honeywell International Inc. Honeywell and is a registered trademark of Honeywell International Inc. All other trademarks are the properties of their respective owners. All rights reserved 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 www.honeywell.com/security Ê800-15963bŠ 800-15963 11/15 Rev B BETA2 Walk Test / Walk Test / Walk Test / Wal NOTE: Before using Test Mode, the device must first be enrolled in the controller. NOTE: To enter Test Mode, the device must first be enrolled in the controller. NOTE: To enter Test Mode, the device must first be enrolled in the controller. NOTE: To enter Test Mode, the device must first be enrolled in the controller. Detection Patterns / Detection Patterns / Detection Patterns / Detection Patterns Approval Listings: FCC / IC SIA-PIR-01 ETL Listed to UL639 cETL Listed to ULC S306-03 RoHS Specifications: Range: 40’ x 56’ / 12 m x 17 m Wall Mounting Height: 7’ – 9’ (2.1 m – 2.7 m); Optimal 7’6” (2.3 m) Battery: 1 x 3V, Lithium; Panasonic CR123A, Duracell DL 123A, Duracell DL 123, Honeywell 466 RF Frequency: 2.4GHz Tamper: Cover and Wall – reported separately to panel. Operating Temperature: 32° – 122° F / 0° – 50° C (Agency Compliance 32° – 120° F / 0° – 49° C) Relative Humidity: 95% max. (Agency Compliance - 93% max.), non-condensing Dimensions: 4.13” H x 2.38” W x 1.61” D / 105 mm H x 60.4 mm W x 41 mm D Product must be tested at least once each year / Le fonctionnement du produit doit être vérifié au moins une fois par année / El producto debe ser probado al menos una vez al año / O produto deve ser testado pelo menos uma vez por ano Replace Battery / Replace Battery / Replace Battery / Replace Battery NOTE: To conserve battery life, the sensor is active only when the system is armed. NOTE: To conserve battery life, the sensor is only active when the system is armed. NOTE: To conserve battery life, the sensor is only active when the system is armed. NOTE: To conserve battery life, the sensor is only active when the system is armed. BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212° F (100° C) or incinerate. Dispose of used batteries properly. Keep away from children. FC:BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212° F (100° C) or incinerate. Dispose of used batteries promptly. Keep away from children. SP: BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212° F (100° C) or incinerate. Dispose of used batteries promptly. Keep away from children. PA: BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212° F (100° C) or incinerate. Dispose of used batteries promptly. Keep away from children. FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une reception indésirable. RF Exposure Warning – The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. Mise en Garde Exposition aux Frequences Radio: L'antenne (s) utilisée pour cet émetteur doit être installée à une distance de séparation d'au moins 7,8 pouces (20 cm) de toutes les personnes. REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM. Support / Support / Support / Support https://mywebtech.honeywell.com/ U.S. warranty / U.S. warranty / U.S. garantie / U.S. garantia www.honeywell.com/security/hsc/resources/wa Zones / Zones / Zonas / Zonas A 18 Lower / Courtes / Cercana/ Mais baixas B 46 Intermediate / Intermédiaires / Intermedia / Intermédias C 36 Long / Longues / Largo Alcance / Longo alcance MyWebTech Warranty

Navigation menu