Hisense Electric LCDX0003 LCD TV User Manual manual front cover nx47013L120

Hisense Electric Co., Ltd. LCD TV manual front cover nx47013L120

Users Manual

EnglishFrançaisEspañol42LED55SA47LED55SA55LED55SAUSER'S MANUAL LCD FULL HD TVPart No IES09EnglishFrançaisEspañol
Important to userFCC StatementNOTE:The manufacturer is not responsible for any radio or TV interference caused by unauthorizedmodifications to this equipment. Such modifications could void the user's authority.NOTE: This equipment has been tested and found to comply with the limits for a class B digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio Communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and the receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. 
Important safety precautionsSafeguardsThe lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric to persons.&$87,21RISK OF ELECTRIC SHOCK DO NOT OPEN! The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.TO REDUCE THE RISK OF AN ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). THERE ARE NO USER SERVICEABLE PARTS INSIDE. FOR ANY REQUIRED SERVICING, PLEASE CONTACT QUALIFIED SERVICE PERSONNEL. Important safety instructionsImportant safety instructionsCAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer to service manual for servicing instructions. 1. Read these instructions 2. Keep these instructions 3. Heed all warnings 4. Follow all instructions 5. Do not use this apparatus near water 6. Clean only with dry cloth 7. Do not block any ventilation openings 8. Do not install near any heat sources 9. Do not defeat the safety purpose of the polarized or grounding-type plug 10. Protect the power cord from being damaged particularly at plugs, convenience receptacles, and at points in which they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 
S3126AANTENNA LEAD IN WIREANTENNADISCHARGE UNITGROUND CLAMPSPOWER SERVICE GROUNDINGELECTRODE SYSTEMELECTRICSERVICEEQUIPMENTGROUNDCLAMPEXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODEFIGURE AS2898AGROUNDING WIRESImportant safety precautionsSafeguards14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when the power-supply cord or plug is damaged, when liquid has been spilled or when objects have fallen into the apparatus, or when the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. POWER SOURCE: This TV should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company . For TVs intended to operate from battery power, or other sources, refer to the operating instructions. 16. POWER CORD PROTECTION: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. 17. OUTDOOR ANTENNA GROUNDING : If an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA NO.70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit , size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig.A) 18. LIGHTNING: For added protection for this TV receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the TV due to lightning and power line surges. 19. POWER LINES: An outside antenna system should not be located in the vicinity of overhead power lines, or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
Important safety precautionsSafeguards 20. OVERLOADING: Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 21. OUTDOOR USE: Do not install this TV outdoor. If the TV is exposed to rain, it may result in a fire or an electric shock. If the TV is exposed to direct sunlight, the TV may heat up and cause damage to the TV. 22. VEHICLE: Do not install the TV in a vehicle. Bumping of the vehicle may cause the TV to fall down and cause injury. 23. SHIP AND VESSEL: Do not install this TV in a ship or vessel. If the TV is exposed to seawater, it may cause a fire or damage the TV. 24. OBJECT AND LIQUID ENTRY: Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill liquid of any kind into the TV. 25. SERVICING: Do not attempt to service this TV yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 26. REPLACEMENT PARTS: When replacement parts are required, be sure that the service technician uses replacement parts with the same characteristics as the original parts specified by the manufacturer. Unauthorized substitutions may result in fire, electric shock, injury to persons or other hazards. 27. SAFETY CHECK: Upon completion of any service or repairs to this TV, ask the service technician to perform routine safety checks to determine that the TV is in proper operating condition. 28. The apparatus should not be exposed to any dripping or splashing, and no objects filled with liquids (such as a vase) should be placed on the apparatus. 29. WARNING: Plug the power cord into a power outlet where access to the power cord connector is readily accessible, in case if the power needs to be immediately disconnected. 30. ATTENTION: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. a). Disposal of packaging:The packaging of this product is intended to be recycled. Apply to the local authorities for correct disposal. b). Disposal of batteries: The batteries supplied do not contain the heavy metals mercury and cadmium. Please check on how to dispose exhausted batteries according to local regulations. c). Note Specifications and information are subject to change without notice. If you need further assistance, please call the customer support service in your country. 31.POWER-CORD INSERT CHECK:When connecting the power cord to the connector of the TV, make sure the power cord is fully inserted in the place. Bad contact may cause high temperature of the connector and the risk of fire or other damages.

Table of Contents 1.Important to user...................................................................................... 2.Important safety precautions.................................................................... Safeguards....................................................................................... 3.Table of Contents..................................................................................... 4.Setting Up................................................................................................. Wall mount specifications................................................................. Installing the Stand........................................................................... TV Front........................................................................................... TV Rear............................................................................................ Connect to other devices................................................................. 5.Using the Remote Control....................................................................... Installing the remote control batteries............................................... Learning about the Remote Control Panel....................................... Quick starts...................................................................................... 6.Changing the TV Settings....................................................................... Using the  Menu................................................................. Using the Video Menu..................................................................... Using the Audio Menu..................................................................... Using the Setup menu..................................................................... Using the Parental menu................................................................. 7.Appendix................................................................................................. Trouble shooting.............................................................................. Specifications...................................................................................1 2 2 Safety Strap....................................................................................... 5 6 7 7 7 8 10 Wall mount..........................................................................................11 12 15 15 16 17 19 19 20 2 22 2Table of Contents
Setting UpInstalling the Stand/Wall mount specificationsWall mount specificationsInstall your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest dealer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury. • Dimensions for wall mount kits and wall-mount screws pattern please refer specifications table. • Do not use screws longer than the standard dimension, as they may cause damage to the inside of the TV set. • For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on their specifications. • Do not use screws that do not comply with the VESA standard screw specifications. • Do not fasten the screws too strongly, this may damage the product or cause the product to fall, leading to personal injury. • Proscan is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions. • Do not exceed 15 degrees tilt when mounting this TV.Installing the Stand1. Lay a cloth or another soft material on a flat surface to avoid damage to the LCD screen. 2. Put the TV back upward and the LCD screen downward and keep it flat on the table-board. 3. Take out the stand and insert the stand into the installing slot in the lower part of the TV, then put the stand to relevant position of the TV set until all the holes match each other completely. 4. Fasten the stand and the TV set together with the 4 screws provided. Erect the TV set, and put it on the proper position for watching. Note: The above figures are for reference only, please refer to the actual units to determine the appearances. Every hole of the stand must be fastened with screws!
Setting UpWall mount Wall mount Unit Dimension(Unit:mm)Screw DiameterScrew Length(Unit:mm)42LED55SA200h200M625M625M825200h200 400h40047LED55SA 55LED55SA
Setting UpWall mount When Installing the TV Against a Wall or Enclosed AreaMake sure that your TV has adequate air circulation. Allow enough space around the TV as shown below. Avoid operating the TV at temperatures below Inadequate air 45° F (5 )Leave at least this much space around the set.Never install the TV set as follows:Air circulation is blocked. Leave at least this much space around the set.Inadequate air circulation can lead to overheating of the TV and may cause damage to your TV or cause a fire.Wall mountwallInstand with standInstall on the wall4 inches10cm4 inches10cm4 inches 10cm12 inches30cm2.375 inches6cm4 inches10cmWall mount 12 inches30cm
BlueThe light is off when TV is turned on.Note:Touch the silk print area according to the need, the TV will response correctly.
TV RearSetting UpTV Rear1Note: The appearance of 42LED55SA 、47LED55SA and 55LED55SA are similar, the picture above is for reference only.COMPONENT1AV1LRYLR75ΩANTBPRPVGAHDMI2HDMI3AUDIOHDMI1VIDEOOUTCOAXIALSERVICEHDMI 4RPBLRPYCOMPONENT2VIDEOAV2The cable tie is only used for the power cord.
Setting UpWarning: Before connecting the TV to any other electronic device, unplug the TV and electronicdevice AC cords from the AC input.Note: Not all following terminals are included on your TV. The actual one refer to "TV Rear".1. Connect to broadcast antenna or the cable TV To have an optimal picture quality, it is strongly recommended to have an external antenna or a cable TV. Note: - It is recommended that coaxial cable (75Ω ) be used to eliminate the interference caused by the mismatched impedance. - The antenna cable should not be bound together with the power cord. - When using the cable TV, please insert the plug of the coaxial cable (75 Ω) directly into the antenna outlet. 2. Connect to AV devices - Connect a Video RCA cable to an appropriate external A/V device such as a VCR, DVD or Camcorder. - Connect RCA audio cables to “R -AUDIO - L” on your set and the other ends to corresponding audio out connectors on the A/V device. Audio RAudio LVCD, DVD, set-top boxes, etc.VideoConnect to other devicesELBAC/TNAAOEDIV LR1VA
PY BPR2PMOC1()LRSetting UpConnect to other devices3. Connecting Component Devices (DVD, DVR (digital video recorder), Blu-Ray) Component video(Y, Pb, Pr)transmits video as separate Y, Pb, Pr signals. Use this connection for high-definition video signals from a DVD or other equipment. - Connect Component video and audio cables to Component inputs (“PR/CR”, “PB/CB”, “Y”) of your set and the other ends to corresponding component video out connectors on the PVR or DVD. - The "Y, PB/CB and PR/CR” connectors on your component devices ((DVD, DVR (digital video recorder), Blu-Ray) are sometimes labeled Y, B-Y and R-Y or Y, CB and CR. (Colors for inputs and cables must correspond on both devices.)RedWhiteRedAudio RAudio LPR/CRBlue PB/CBGreen YDVD With Component jacks4. Connect to devices with HDMI interface HDMI High Definition Multimedia Interface HDMI transmits an all-digital signal and is the recommended choice for playback from a digital DVD or DVR. No sound connection is needed for HDMI to HDMI connection. - HDMI cable connected to the HDMI connector on the TV.HMDIThe equipment with HDMIoutput jack ( such as DVDplayers, set-top boxes, etc.).
Setting UpConnect to other devices5. Connect to PC - Connect the D- Sub cable to “VGA” on the side of your set and the other end to the Video Card of your computer. - Connect the stereo audio cable to “PC AUDIO ” on the side of your set and the other end to “Audio Out” of the sound card on your computer. Note: For some sets "PC AUDIO" share with component.6. Connect to headphone - Connect the headphone jack of the TV set. The volume of the headphone is automatically adjusted with the main volume of the TV set. AGV O INIDUAComputerHEADPHONEHeadphone
Using the remote ControlInstalling batteriesInstalling the remote control batteries 1. Open the battery cover on the back of the remote control. 2. Install two AAA size(1.5V) batteries. Match the “+” and “-” signs on the batteries to the signs on the battery compartment. 3. Close the battery cover.Note: 1. Dispose of your batteries in a designated disposal area. Do not throw the batteries into fire. 2. Do not mix battery types or combine used batteries with new ones. 3. Remove depleted batteries immediately to prevent battery acid from leaking into the battery compartment. 4. If you do not intend to use the remote control for a long time, remove the batteries. 5. The effective range of remote control is suggested below. Remote control range 1. The remote control distance: 8 meters(26.2 feet) in front of the TV set. 2. The remote control angle: taking the television infrared light receiver window as an apex, 6 meters (19.7 feet) away, its controlled angle (left to right) is within 30 degrees, while the vertical angle (up to down)is within 30 degrees.
Remote Control Panel Buttons instructions(1) Power On/Off. (2) Power indicator. (3) INPUT: Switch among TV, Video, Component, HDMI and VGA. (4) 0-9 Numbers: For direct channel access. (5) Last: Return to previous channel. (6) — : Select digital channels. (7) PICTURE: Picture Mode selecting. (8) SOUND: Sound Mode selecting. (9) DISPLAY: Display current status information. (10) MUTE: Mute the sound. (11) VOLΛ /V: Volume increase/Volume decrease. (12) CHΛ /V: Next channel/Previous channel. (13) MENU: Display the main menu/Back menu display. (14) EXIT: On screen display (OSD) menu exit. (15) ENTER: Enter or confirm the operation/return to the previous menu. ▲/▼/◄/ ►: Up/Down/Left/Right operation. (16) MTS/SAP: . (17) ASPECT: Select screen mode. (18) CCD: Closed caption decoder function. (19) GUIDE: ATSC tuners feature the Electronic Program Guide (EPG) function. (20) Sleep: Set the sleep timer. (21) TIME: Display the current timer. (22) Electronic Program Guide(EPG) function: After pressing the "GUIDE" button in the digital TV channel option, the 4 same color buttons will appear with explanations in the OSD. Follow the steps illustrated in the OSD. (23) NOT supported in this TV. These buttons are for DVD Combo TV. Note:The design of the remote control is subject to change and may be different from the actual one. Those buttons without comment have no relations with this TV.Using the Remote ControlLearnin12g about the remote control panel
Quick startsBasic Operation Power ON/OFF 1. Connect the TV to a power outlet. If the power indicator is blue, it means that the TV is STANDBY. Press the Standby button on the front control or on the remote control to turn the TV on. Once the TV is turn on, the power indicator will be turned off. Several seconds later, the TV picture will be displayed on the screen. 2. Press the Standby button on the front control or on the remote control to turn the TV off temporarily. 3. Always remove the AC power plug from the outlet when not using this TV for a long period of time. Signal source selection Press the [INPUT] button to select TV, AV, Component, VGA and HDMI inputs. There are two ways to select the source: One is to press the [INPUT] button continuously, while the other is to use the ARROW and [ENTER] buttons to confirm the source. Select channels Please use [CHΛ / CHV] button on the remote panel to select channels. [CHΛ] indicates channel number up; [CHV] indicates channel number down. Press [CHΛ / ChV] button on the side panel of the TV to select the channels. If you want to choose any of the skipped channels, press the number directly. Use [Mute] button Press the [Mute] button to mute the sound. Press the [Mute] button again to resume the sound. Select picture modes Press the [PICTURE] button to select the picture mode from four options: Standard, Cinema, User or Vivid. You can adjust the picture mode based upon your personal preference. Select sound modes Press the [AUDIO] button to select sound modes from Standard, Speech, User or Music. Select screen modes Press the [ASPECT] button to select from six zoom modes: Wide, Normal, Zoom, Cinema , Dot-to-Dot or Auto. Use [GUIDE] button Press the [GUIDE] button to display features of the ATSC program and the EPG function. Use [DISPLAY] button Press the [DISPLAY] button to view current source information. Using the Remote ControlConnecting power cord to the TV1. Connect the power cord to the connector on the back of the TV, if the power cord in accessories. Note:When connecting the power cord to the connector of the TV, make sure the power cord is fully inserted in the place. Bad contact may cause high temperature of the connector and the risk of fire or other damages. 2. Connect the power cord to the AC power outlet.
Using the Remote ControlQuick startsSelect channels by numbers To select a channel: Press the channel number you would like to go to. For example, to select channel number 120, press buttons 1, 2 and 0, respectively and then press [ENTER] to confirm. Use [MENU] button Press the [MENU] button to display the TV OSD menu. Use [LAST] button Press the [LAST] button to return to the previous channel. Use [ENTER] button Press the [ENTER] button to select a particular item. Adjust Volume Press [VOLΛ / VOLV] button to adjust the volume. Use [CCD] button Press the [CCD] button to change the CCD mode. Using this button will set the Closed Caption mode when viewing a DTV or TV channel. Note: Set the default Closed Caption setting for all channels in the Menu. For ATV the options are CC1, CC2, CC3, CC4, TEXT1, TEXT2, TEXT3, TEXT4 or Off. For DTV, the options are from Service1 to Service6 or Off. Use [MTS/SAP] button Press the [MTS/SAP] button to change the sound mode (Mono, Stereo, SAP). This button will select the MTS options of Stereo, SAP, or Mono in TV mode, alternate audio channels, and when available, in DTV mode. Use [SLEEP] button Press the [SLEEP] button repeatedly to set the sleep time, which can be set to: 10 Mins, 20 Mins, 30 Mins, 40 Mins, 50 Mins, 60 Mins, 90 Mins, 120 Mins or Off. Use [TIME] button Press the [TIME] button to display the current time. Use [EXIT] button Press the [EXIT] button to exit the OSD menu. 
Trouble shootingAppendix
Specifications Model 42LED55SA 47LED55SA 55LED55SAScreen Diagonal SizeScreen ResolutionPower ConsumptionPower SupplyTelevision SystemAudio multiplexChannel coverageVHF: 2~13 UHF: 14~69 CATV: 1~125Sound Output Power (RMS)Component (Y/Pb/Pr) modePC (VGA) modeHDMI modeWall-mount screws patternWall-mount dimension(VESA)Size with base(inch)(L X WX H)Weight with base(lbs)Environmental ConditionsSupplied accessories 42 inches 47 inches 55 inches 1920X1080 Pixels 1920X1080 Pixels 1920X1080 Pixels165W 180W 195W AC 60Hz 120V American TV standard NTSC / ATSC system BTSC systemDigital Terrestrial Broadcast (8VSB): 2~69Digital Cable(64/256 QAM): 1~135W+ 480I/60Hz, 480P/60Hz, 720P/60Hz, 1080I/60Hz640X480/60Hz, 800X600/60Hz,1024X768/60Hz480I/60Hz, 480P/60Hz, 720P/60Hz, 1080I/60Hz, 1080P/60Hz640X480/60Hz, 800X600/60Hz,1024X768/60HzM6X25mm (4 pcs)00mm X 200mmM6X25mm (4 pcs)00mm X 00mmM8X25mm (4 pcs)400mm X 400mm40.6×11.5×2.144.2 lbs45×11.2×30.756.1 lbs52.×1.×399 lbsHumidity : 20%-80%RH Atmospheric pressure: 86kPa-106kPa Remote control, Batteries, User Manual, Quick Start Guide, Remote Control Guide, Children Safety Guide, Warranty Card, Registration CardAppendixNote: Design and specifications are subject to change without notice. CUSTOMER NOTICE: Use carefully when operating to prevent damage to the screen. 

Navigation menu