Hisense Broand Technology HBMT06 GPON SFU User Manual

Guangdong Hisense Broadband Technology Co.,Ltd. GPON SFU

User manual

Page 61299 Commerce Dr.Richardson, TX 75081214-575-9300 Page 1Page 7FCC Notice -1This device complies with part 15 of the FCCRules. Operation is subject to the following twoconditions: (1) This device may not cause harm-ful interference, and (2) this device must acceptany interference received, including interferencethat may cause undesired operation.This equipment has been tested and found tocomply with the limits for a Class B digitaldevice, pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonableprotection against harmful interference in a resi-dential installation. This equipment generates,uses and can radiate radio frequency energy, andif not installed and used in accordance with theinstructions, may cause harmful interference toradio communications. However, there is noguarantee that interference will not occur in a.noitallatsni ralucitrapIf this equipment does cause harmful interferenceto radio or television reception, which can bedetermined by turning the equipment OFF andON, the user is encouraged to try to correct theinterference by one or more of the followingmeasures:•Reorient or relocate the receiving antenna•Increase the separation between the equip-ment and receiver•Connect the equipment to an outlet on a cir-cuit different from that to which the receiver is connected•Consult the dealer or an experienced radio/TV technician for helpThe manufacturer is not responsible for any radioor TV interference caused by unauthorized modi-fications to this equipment. Such modificationscould void the user’s authority to operate theequipment.FCC RF Safety Caution StatementTo satisfy FCC RF exposure requirement formobile and base station transmission devices, aseparation distance of 20cm or more should bemaintained between the antenna of this deviceand persons during operation. To ensure compli-ance, operation at closer than this distance is notrecommended. The antenna(s) used for this trans-mitter must not be co-located or operating in con-junction with any other antenna or transmitter.© Copyright 2013, iPhotonix GPON SFU ONTQuick Install GuideFCC Notice -2This device is intended to be attached to a receiverthat is not used to receive over-the-air broadcast sig-nals. Connection of this device in any other fashionmay cause harmful interference to radio communica-tions and is in violation of the FCC Rules, part 15.The 72xxG North America edition is limited usingchannel 1-11. This limited operation can be only setby software and was done before the product downfrom the product line. All the products for NorthAmerica marketing were embedded this limitedbefore shipping. Customers have no way to choosethe channel 12 & 13.OVERVIEWThe 72xx SFU residential ONT delivers highquality VoIP voice service, Ethernet data servicefor high-speed internet access and IPTV broad-cast video plus video on demand services. Theyprovide the following user features: (see ModelList for exact features)– 2 POTS ports - voice telephone service – 4 LAN ports - Ethernet connectivity– WiFi ports - WiFi connectivity– CATV ports - CATV and Return service– USB ports - data backups service– UPS ports - UPS serviceINSTALLATIONThe 72xx SFU ONT can be mounted vertically orhorizontally on any flat surface.UnpackUnpack the unit and verify that it is free fromshipping damage.:Desk Mount1.) Set the unit on a flat surface considering thefollowing:– within reach of the power source– no thermal obstructions– not in direct sunlight– user ability to monitor/operate the unitWall Mount1.) Use wall anchors or wood screws (if mountingto plywood mounted on a wall), spaced 5.709”apart center to center for horizontal mounting or3.543” apart center to center for vertical mount-ing. 技术要求： 1、标签用于IPHOTONIX室内机项目；2、折叠后尺寸64X154mm;折叠后封面朝上；3、材质：70g书写纸；4、印刷颜色：黑色印刷，双面印；5、公差±1mm；6、材料及印刷工艺均满足ROHS要求。
Page 2 4 egaP3 egaP Page 5Fiber Connection1.) On the back left side of the unit is fiber cover.Slide it off as shown. 2.) With the fiber connector exposed, remove thedust plug, clean the fiber ends and terminate theSC equipped fiber. Danger! . Exposure to invisible LASER radiation may cause serious retinal damage or even blindness. Verify the optical source is disabled through the use of an optical power meter before handling optical fibers.3.) Insert the fiber into the cover slot and slide thecover back onto the 72xx unit.DC Power Input1.) Connect the 2.1mm DC power plug to theport labeled PWR.UPS Power and Alarms1.) The UPS power/alarminput uses a MOLEX 43025-0800 connector. Pin orienta-tion as shown is viewed fromthe rear.Pins for the connector are Molex 46235-5002NOTICE: Please adopt UL certificated UPS whichmeets Limited Power Source standard.POTS Connections1.) Connect up to 2 phones to the ports labeled POTS1and POTS2.LAN Connections1.) Connect the computers/routers to the ports labeledETH1 through ETH4.CATV Connection1.) Connect the television to the port labeled CATV.This port supports Return Service on select models.PIN NAME ALM1 Power Input (+12 VDC) –2 UPS Status: On Battery 13 UPS Status: Battery Missing 24 Signal Return –5 Power 12V Return –6 UPS Status: Replace Bettery 37 UPS Status: Low Battery 48 No Connection (N/A) –WiFi Connection1.) Change the notebook/computer WiFi networkSSID to “iphotonix-ONTxxxx”. This may be changedmanually.USB Connection1.) Connect the flash-disk/portable hard disk to theport labeled USB on the left side of the units.User Controls1.) The 72xx SFU ONT is equipped with an ON/OFFbutton. User functionality should be limited to thisbutton.LED DescriptionsThe 72xx SFU ONT has visual LED indicators tohelp the user determine the operational state of theunit. The LEDs are defined as follows:PowerBatteryMGMTON Unit is powered onOFF Unit is powered offON Battery is charged and unit is operating nor-mally on external power.Flashing Slow Unit is running off of battery power only. Check power supply to unit.Flashing Fast Battery is low and unit may turn off if exter-nal power is not restored.OFF Battery is missing or defective.ON Management channel (OMCI) is activeOFF Management channel (OMCI) is not active.ETH 1- 4POTS FAILWLAN Environmental RequirementsModel ListON Ethernet link is operational.Flashing Indicates data transmission / reception.OFF No Ethernet link or port is not equipped.ON Line is off hook (call active or in process)Flashing Slow Indicates ringing line.OFF Line is on hook (no call in process) or port is not equipped.ON Indicates Loss Of Signal (LOS). No opti-cal signal is present.Flashing SlowMarginal signal indicates a weak optical signal from carrier. Clean fiber connection per local practice and check power with an optical meter.Flashing Fast Software upgrade has failed.OFF Optical signal is present and operating nor-mally.ON WiFi function is active (+2– -6 range)Flashing Indicates active data TX/RXOFF WiFi function is not activeRated Voltage: DC 12VRated Current: 2AOperating Temperature: +5°C to +40°COperating Relative Humidity: 5% to 85% Storage Temperature: -40°C to +60°CStorage Relative Humidity: 0% to 95%Model Functions Select7259G 2POTS + 4GE + CATV + Return + WiFi7257G 2POTS + 4GE + CATV + Return7258G 2POTS + 4GE + CATV + WiFi7253G 2POTS + 4GE + CATV7281G 2POTS + 4GE + WiFi7251G 2POTS + 4GE

Navigation menu