Hirschmann Automation and Control EWLAN2 802.11abgn Module User Manual U99EWLAN2 integration manual

Hirschmann Automation and Control GmbH 802.11abgn Module U99EWLAN2 integration manual

user manual

Integration Information FCC ID: U99EWLAN2 IC: 4019A-EWLAN2 Page 1 of 9 EWLAN2 integration manual The EWLAN2 Module is a 3x3 3-stream IEEE 802.11 a/b/g/n wireless LAN module in PCI express mini card form factor, designed to deliver high-reliable radio performance for a variety of bandwidth-intensive wireless applications. Outer Appearance Top view with Samtec connector (PCI express): Rear view with antenna connectors: Dimensions: 34 mm (w) x 54mm (l) x 10 mm (h)
Integration Information FCC ID: U99EWLAN2 IC: 4019A-EWLAN2 Page 2 of 9 General requirements: This module is designed exclusively for usage in Hirschmann (Belden) host equipment. A regulated power supply via the dedicated interface to the WLAN module is required. This RF module is approved only for use in products operating as fixed or mobile transmitting device where the antennas are at least 50 cm away from any persons during normal operating conditions. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment authorizations (e.g. Verification , Doc) of the host device to be addressed by the integrator/manufacturer. Hardware Integration EWLAN2 supports the PCI express standard from the electrical power supply and signaling point of view. To enhance connection reliability in harsh environments between EWLAN2 and the host equipment, Samtec interface connectors have been selected.
Integration Information FCC ID: U99EWLAN2 IC: 4019A-EWLAN2 Page 3 of 9 EWLAN2 is equipped with Samtec connector QRM8 The host equipment has to be equipped with Samtec connector QRF8-026-05.0-L-D-A-GP Pin assignment of QRF8-026-05.0-L-D-A-GP
Integration Information FCC ID: U99EWLAN2 IC: 4019A-EWLAN2 Page 4 of 9 Data Interface Pin definition Pin Signal Comment Pin Signal Comment 1 GND ground 2 GND ground 3 Res open 4 Res open 5 GND ground 6 Res open 7 Res open 8 Res open 9 GND ground 10 Res open 11 Res open 12 GPIO10 GPIO-Interface 13 Res open 14 GPIO7 GPIO-Interface 15 GND ground 16 GND ground 17 Res open 18 PERST_L /Reset 19 GND ground 20 GND ground 21 VCC3.3 3.3V ±5% 22 VCC3.3 3.3V ±5% 23 VCC3.3 3.3V ±5% 24 VCC3.3 3.3V ±5% 25 GND ground 26 GND ground 27 Res open 28 PETp0 PCIe Tx+ 29 GND ground 30 PETn0 PCIe Tx- 31 Res open 32 GND ground 33 Res open 34 PERp0 PCIe Rx+ 35 GND ground 36 PERn0 PCIe Rx- 37 GND ground 38 GND ground
Integration Information FCC ID: U99EWLAN2 IC: 4019A-EWLAN2 Page 5 of 9 39 VCC1.2 1.2V ±5% 40 REFCLK+ PCIe Ref Clock+ 41 VCC1.2 1.2V ±5% 42 REFCLK- PCIe Ref Clock- 43 GND ground 44 GND ground 45 GND ground 46 GND ground 47 Res open 48 CLKreq_L /Clock request 49 Res open 50 WAKE_L /PCIe awake 51 GND ground 52 GND ground
Integration Information FCC ID: U99EWLAN2 IC: 4019A-EWLAN2 Page 6 of 9 Power Requirements EWLAN2 has to be powered as follows: 3.3VDC at VCC3.3 1.28VDC at VCC1.2 Antenna Connectors The antenna connectors of EWLAN2 are micro miniature coaxial types (MMCX). Antennas (USA/Canada) The usage of the antennas for products shipped to North America (USA and Canada) is restricted to the models and bands below: Antennas operating with this device model (Hirschmann model names) Permitted band of operation 2.4 GHz Band 5.15-5.25 GHz Band 5.725-5.825 GHz Band BAT-ANT-RSMA-2AGN-R (1) Yes Yes Yes BAT-ANT-N-3AGN-IP67 Yes Yes Yes BAT-ANT-N-MiMoDB-5N-IP65 Yes Yes Yes BAT-ANT-N-MiMo5-9N-IP65 No Yes Yes BAT-ANT-N-8G-DS-IP65 Yes No No BAT-ANT-N-MiMo-18N-IP65 (2) No No Yes Note (1): When using three antennas of the type BAT-ANT-RSMA-2AGN-R, each antenna has to be aligned into a separate spatial direction (x-y-z), where one antenna is perpendicular to the device and the other two are at right angles to each other. Note (2): Antenna BAT-ANT-N-MiMo-18N-IP65 has to be connected to the WLAN main unit as below: Antenna port “Ver” to WLAN antenna port 1 Antenna port “+45” to WLAN antenna port 2 Antenna port “-45” to WLAN antenna port 3 Other connection combinations are not permitted.
Integration Information FCC ID: U99EWLAN2 IC: 4019A-EWLAN2 Page 7 of 9 SW Integration EWLAN2 is designed for usage with Hirschmann host equipment (motherboards) running the HiLCOS operating system 8.60.x or higher versions. Only HiLCOS versions with fixed (non-adjustable) radio parameters for USA/Canada are allowed for products intended for the North American market. Regulatory Requirements (FCC/IC) If intended for the North American market the following regulatory requirements apply: 1) ELWAN1 needs to be labeled with the FCC ID and Canada number: FCC ID: U99EWLAN2 IC: 4019A-EWLAN2 2) The host product need to be labeled as below: 3) The user guide of the host equipment shall contain the following information: FCC note: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:  This device may not cause harmful interference, and  This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-3 (B)/NMB-3(B) Contains Transmitter Module FCC ID: U99EWLAN2 IC: 4019A-EWLAN2
Integration Information FCC ID: U99EWLAN2 IC: 4019A-EWLAN2 Page 8 of 9 uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: The following paragraph is valid for devices labeled with FCC ID: U99EWLAN2 and IC: 4019A-EWLAN2: Important note: This equipment complies with FCC and IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 50 cm (19.7 in, applied to a 18 dBi antenna) between the radiator and your body. The antenna used for this transmitter must not be co-located with any other transmitters within a host device, except in accordance with FCC multi-transmitter product procedures. This transmitter is restricted to indoor use only within the 5.15-5.25 GHz band to reduce potential for harmful interference to co-channel mobile satellite systems. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that permitted for successful communication. This device has been designed to operate with the antennas listed below having a maximum gain of 18 dBi: Antennas operating with this device model: Permitted band of operation 2.4 GHz Band 5.15-5.25 GHz Band 5.725-5.825 GHz Band BAT-ANT-RSMA-2AGN-R (1) Yes Yes Yes BAT-ANT-N-3AGN-IP67 Yes Yes Yes BAT-ANT-N-MiMoDB-5N-IP65 Yes Yes Yes BAT-ANT-N-MiMo5-9N-IP65 No Yes Yes BAT-ANT-N-8G-DS-IP65 Yes No No BAT-ANT-N-MiMo-18N-IP65 (2) No No Yes Antennas not included in this list are prohibited for use with this device. The required antenna impedance is 50 ohms.
Integration Information FCC ID: U99EWLAN2 IC: 4019A-EWLAN2 Page 9 of 9 Note (1): When using three antennas of the type BAT-ANT-RSMA-2AGN-R, each antenna has to be aligned into a separate spatial direction (x-y-z), where one antenna is perpendicular to the device and the other two are at right angles to each other. Note (2): Antenna BAT-ANT-N-MiMo-18N-IP65 has to be connected to the WLAN main unit as below: Antenna port “Ver” to WLAN antenna port 1 Antenna port “+45” to WLAN antenna port 2 Antenna port “-45” to WLAN antenna port 3 Other connection combinations are not permitted.

Navigation menu