Hilti PD38XR01 LASER RANGEMETER User Manual

Hilti Corporation LASER RANGEMETER Users Manual

Users Manual

*228790*228790Hilti CorporationFL-9494 SchaanTel.: +423 / 234 21 11Fax: +423 / 234 29 65www.hilti.comHilti = registered trademark of Hilti Corp., Schaan W 3153 1105 00-Pos. 4 1 Printed in Liechtenstein © 2005Right of technical and programme changes reserved S. E. & O. 228790 / A
PD 38Bedienungsanleitung deOperating instructions en
Ẅ52496317128101011111113
PDAW 80-1 ẅPDA 50PDA 60PDA 61PDA 62PDA 70PDAW 80 / 81-3PDAW 81-1PDAW 80 / 81-2PDAW 80 / 81-1PDA 81PDA 80PUA 60PDA 66
PD 38 laser range meter ContentsIt is essential that the operatinginstructions are read before the rangemeter is used the first time.Always keep these operating instruc-tions together with the range meter.Ensure that the operating instructionsare with the range meter when it isgiven to other persons.Component parts ẄቢLaser exit apertureባControl panelቤReceiving lensብPlastic casingቦHorizontal bubble ቧVertical bubbleቨBattery compartmentቩFolding spikeቪGraphic display showing operating statusቫMetal contact points for precise meas-urement (3x rear)ቭMetal supports for precise measure-ment (3x underneath)ቮOptical sightቯSide measure buttonContents1. General information. . . . . . . . . . 31.1 Safety notices and their meaning . . . . . . . . . . . . . . . . . . . 31.2 Pictograms . . . . . . . . . . . . . . . . . 31.3 Location of identification data onthe range meter . . . . . . . . . . . . . 32. Description. . . . . . . . . . . . . . . . . 42.1 Intended use. . . . . . . . . . . . . . . . 42.2 Items supplied . . . . . . . . . . . . . . 42.3 Measuring principle . . . . . . . . . . 42.4 Range meter functions . . . . . . . . 42.4.1 General range meter functions . . 42.4.2 PD 38 side measure button . . . . 42.4.3 PD 38 optical sight . . . . . . . . . . . 42.5 Bluetooth . . . . . . . . . . . . . . . . . . 43. Tools and accessories . . . . . . . . 63.1 PDA 50 target plate. . . . . . . . . . . 63.2 PDA 80/81charging kits . . . . . . . 63.3 PDAW 80-1 mains adapter . . . . . 63.4 PDAW 80/81-2 car battery plug. . . . . . . . . . . . . . . . . . . . . . . 73.5 PDAW 80/81-1 charging adapter . 73.6 PDAW 80/81-3 battery pack . . . . 73.7 PDAW 81-1 mains adapter . . . . . 73.8 PUA 60 laser visibility glasses . . 73.9 PDA 62 belt clip . . . . . . . . . . . . . 73.10 PDA 70 measuring extension . . 73.11 PDA 66 Holder . . . . . . . . . . . . . . 74. Technical data . . . . . . . . . . . . . . 85. Safety information . . . . . . . . . . . 95.1 Basic safety information . . . . . . . 95.2 Misuse . . . . . . . . . . . . . . . . . . . . 95.3 General safety precautions . . . . . 95.4 Proper organization of workplace . . . . . . . . . . . . . . . . . 105.4.1 Electromagnetic compatibility. . 105.4.2 Laser classification . . . . . . . . . . 105.4.3 Transport . . . . . . . . . . . . . . . . . 101
2Contents6. Getting started . . . . . . . . . . . . . 116.1 Inserting alkaline/rechargeable batteries . . . . . . . . . . . . . . . . . . 116.2 Battery charging . . . . . . . . . . . . 116.2.1 Standard charging of batteries . 116.2.2 Fast battery charging . . . . . . . . 126.3 Switching the range meter on and off . . . . . . . . . . . . . . . . . 126.3.1 Initial distance measurement . . 126.4 Settings. . . . . . . . . . . . . . . . . . . 136.4.1 Activating the settings menu . . 136.4.2 Menu/Beep . . . . . . . . . . . . . . . . 136.4.3 Menu/Units . . . . . . . . . . . . . . . . 136.4.4 Switching Bluetooth on and off. 136.4.5 Terminating the menu. . . . . . . . 137. PD 38 operation. . . . . . . . . . . . 147.1 General controls . . . . . . . . . . . . 147.1.1 Control panel . . . . . . . . . . . . . . 147.1.2 On/off and control buttons . . . . 147.1.3 Measure buttons. . . . . . . . . . . . 147.1.4 Function buttons. . . . . . . . . . . . 147.2 Display . . . . . . . . . . . . . . . . . . . 157.2.1 Symbols displayed . . . . . . . . . . 157.2.2 Display illumination . . . . . . . . . 167.3 Optical sight . . . . . . . . . . . . . . . 167.4 Measuring distances. . . . . . . . . 177.4.1 Measuring references . . . . . . . . 177.4.2 Measuring distances step by step . . . . . . . . . . . . . . . . . . . . . . 177.4.3 Measurement mode . . . . . . . . . 187.4.4 Measuring from corners . . . . . . 197.4.5 Measuring with the aid of targetobjects . . . . . . . . . . . . . . . . . . . 197.4.6 Measuring in bright conditions . . 197.4.7 Taking measurements to roughsurfaces . . . . . . . . . . . . . . . . . . 207.4.8 Taking measurements to round or inclined surfaces . . . . . . . . . 207.4.9 Taking measurements to wet orshiny surfaces. . . . . . . . . . . . . . 207.4.10 Taking measurements totransparent surfaces. . . . . . . . . 207.4.11 Measuring ranges. . . . . . . . . . . 208. Applications and functions . . . 218.1 Measurement data memory . . . 218.1.1 Saving measurements . . . . . . . 218.1.2 Historical data memory. . . . . . . 218.2 Area measurement . . . . . . . . . . 218.3 Volume measurement. . . . . . . . 228.4 Adding distances . . . . . . . . . . . 238.5 Subtracting distances . . . . . . . . 238.6 Setting out . . . . . . . . . . . . . . . . 249. Measuring using a Bluetooth connection . . . . . . . . . . . . . . . . 259.1 Setting up PDA/MDA . . . . . . . . 259.2Establishing connection betweenPD 38 and PDA/MDA . . . . . . . . 259.3 Measuring using Bluetooth connection to PDA/MDA . . . . . . 2610. PDA/MDA Windows CE with Hilti PD 38 application . . . . . . 2711. Data transfer from PDA/MDA to PC. . . . . . . . . . . . . . . . . . . . . 2812. Calibration and adjustment. . . 2912.1 Calibration. . . . . . . . . . . . . . . . . 2912.2 Adjustment . . . . . . . . . . . . . . . . 3012.3 Hilti calibration service . . . . . . . 3013. Care and maintenance. . . . . . . 3013.1 Cleaning and drying . . . . . . . . . 3013.2 Storage . . . . . . . . . . . . . . . . . . . 3013.3 Transportation. . . . . . . . . . . . . . 3014. Disposal . . . . . . . . . . . . . . . . . . 3115. Warranty. . . . . . . . . . . . . . . . . . 3116. FCC statement (applicable inUSA) . . . . . . . . . . . . . . . . . . . . . 3217. Troubleshooting . . . . . . . . . . . . 3318. Bluetooth declaration ofcompliance. . . . . . . . . . . . . . . . 3319. EC declaration of conformity. . 34
31. General information1. General information1.1 Safety notices and their meaning-CAUTION-This word indicates a possibly hazardoussituation which could result in slight bodilyinjuries or damage to property.-NOTE-This word indicates information to help theuser employ the product efficiently, andother useful notes.1.2 PictogramsWarning signsSymbols Ẅ These numbers refer to the correspon-ding illustrations. The illustrations can befound on the fold-out cover pages. Keepthese pages open when studying the oper-ating instructions. In these operatinginstructions, the PD 38 laser range meter isreferred to as «the range meter ».1.3 Location of identification data on therange meterThe type designation and serial numbercan be found on the rating plate on therange meter. Make a note of this data inyour operating instructions and alwaysrefer to it when making an enquiry to yourHilti representative or service department.Type : ___________Serial no.: ___________General warningLaser class 2(Do not stare into thebeam.)Read the operatinginstructions beforeuse.Return waste materialfor recycling.
2. Description2. DescriptionThe distance is determined along a laserbeam emitted by the range meter up to thesurface where the laser beam is reflected.The red laser spot clearly identifies the tar-get from which the measurement is taken.The measuring range depends on thereflectivity and the surface structure of thetarget surface.2.1 Intended useThe range meter is designed for:– Measurement of distances– Calculation of areas, volumes and distances– Addition and subtraction of distances– Operation and storage in the specifiedtemperatures2.2 Items supplied1 PD 38 laser range meter1 PDA 50 target plate1 PDA 60 hand strap1 PDA 66 holder2 type AA batteries1 soft pouch1 operating instructions1 producer certificate2.3 Measuring principleThe range meter emits a visible laser beamcarrying a wave signal which is reflectedand received with a phase shift. The phaseshift is used to determine the distance.This measuring principle permits highlyaccurate and reliable distance measure-ments to objects without use of specialreflectors.2.4 Range meter functions2.4.1 General range meter functions2.4.2 PD 38 side measure button2.4.3 PD 38 optical sight2.5 BluetoothBluetooth technology enables wireless dataexchange over short distances with fast,reliable and secure data connection main-tained typically over 10 m (30 ft). Transmission range can drop to about 5 m(15 ft) under very unfavourable conditionsbut can also reach up to 20 m (60 ft) undervery favourable conditions.EyeOptical sightMeasurement reference point On / offVertical bubble Side measure buttonMeasure buttonAddition of distancesSubtraction of distancesBattery charging contactsLiquid crystaldisplayVolume functionArea functionHorizontal bubble Spike Display illuminationphi4
52. DescriptionUnfavourable conditions for Bluetoothcommunication range• Steel surfaces in immediate surroundings• PD 38 is placed in corners or on wet sur-faces• PD 38 and PDA/MDA are held in wethands• Obstructions between PD 38 and PDA/MDA, e.g. thick wall with a lot ofsteel reinforcement, wire mesh, etc…Favourable conditions for Bluetooth communication range• Direct sight between PD 38 andPDA/MDA without any obstructions• PD 38 and PDA/MDA kept at adequatedistance (approx. 0.5 m, 2 ft) walls andsteel surfaces, etc…• PD 38 and PDA/MDA are held in dryhands
63. Tools and accessories3. Tools and accessories ẅDescription DesignationTarget plate PDA 50Hand strap PDA 60Soft pouch PDA 61Belt clip PDA 62Measuring extension PDA 70Charging kit PDA 80Charging kit PDA 81Mains adapter PDAW 80-1Mains adapter PDAW 81-1Car battery plug PDAW 80/81-2Charging adapter PDAW 80/81-1Battery pack PDAW 80/81-3Laser visibility glasses* PUA 60* These are not laser safety glasses and do not protect theeyes from laser radiation. Thelaser visibility glasses restrictcolour vision. These glasses aretherefore not permitted to beworn by a person driving on apublic road and must not beused to look directly into the sun3.1 PDA 50 target plateThe PDA 50 target plate is made of durableplastic with a special reflective coating. Inpoor light conditions it is advisable to usethe target plate for distances above 10 m(30 ft).-NOTE-– For reliable distance measurements thelaser beam should be perpendicular tothe target plate whenever possible. If thisis not the case, the laser spot on the tar-get plate may not be in the same planeas the target point and the distancemeasured will be incorrect.– For very accurate measurements usingthe target plate, 1.2 mm (1/20 inch)should be added to the measured dis-tances.3.2 PDA 80/81 charging kitsThe PDA 80 and PDA 81 charging kitsenable use of the range meters withrechargeable cells. Battery charging time isapprox.12 hours for fully discharged cells.However, within the first 15 minutes, thecells are charged with sufficient current for150–200 measurements.Please also refer to the description of bat-tery charging in section 6. “Getting start-ed”.Contents of PDA 80 charging kit– Mains adapter 100–240 V AC with 2-pole Europlug– Car battery plug– Charging adapter for range meter– 2 rechargeable battery cells (NiMH)Contents of PDA 81 charging kit– Mains adapter 100–240 V AC with 4interchangeable plugs for US, GB, AUS,EU.– Car battery plug– Charging adapter for range meter– 2 rechargeable battery cells(NiMH)3.3 PDAW 80-1 mains adapterThe mains adapter is an integral part of thecharging kit. It is equipped with a two-pinplug. The mains adapter transforms thepower from alternating current to direct
73. Werkzeuge und Zubehörcurrent which is used to charge the batter-ies. The mains adapter automaticallyadjusts itself to suit an AC voltage between100–240 V and 50–60 Hz. The mainsadapter has been specially designed tosupply current to the charging adapter.-NOTE-Battery chargers or mains adapters withother voltage outputs, such as those formobile phones, may not be used. Use ofother battery chargers or mains adaptersmay damage the range meter.3.4 PDAW 80/81-2 car battery plugThe car battery plug is an integral part ofthe PDA 80/81 charging kit. It can beinserted into a vehicle cigarette lighter orinto sockets of the same design. Thisadapter has a special design and trans-forms the 12–24 V direct current of a vehi-cle battery into a voltage suitable for thecharging adapter.A light-emitting diode (LED) is incorporat-ed in the adapter to indicate correct con-nection for charging. An additional fuse inthe adapter’s front section provides protec-tion against voltage peaks.-NOTE-As the car battery plug has been especiallydesigned to charge the NiMH batteries ofthe PD 38, it may not be replaced by othertypes of car battery plugs.3.5 PDAW 80/81-1 charging adapterThe respective mains adapter supplies cur-rent to the charging adapter. Prior tocharging the battery, the side flange con-nections should be carefully checked.3.6 PDAW 80/81-3 battery packThe battery pack consists of two recharge-able, 1.2 V NiMH cells with a capacity ofapprox.1800 mAh. The battery packremains in the battery compartment whilebeing charged.-NOTE-– There is virtually no “memory effect”with this type of battery and the chargingprocess used. The charging process can be interruptedat any time without damaging the batterycells.– Other brands of rechargeable batteriescan be used. It must be ensured, howev-er, that the batteries have a similarcapacity of approx. 1800 mAh.3.7 PDAW 81-1 mains adapterThe PDAW 81-1 mains adapter is virtuallyidentical to the PDAW 80-1 mains adapter.The only difference is the type of mainsplugs (interchangeable plugs).3.8 PUA 60 laser visibility glassesThe laser visibility glasses clearly improvethe visibility of the laser beam (spot).3.9 PDA 62 belt clipThe belt clip is made from durable plasticsand is quickly and easily fixed to the beltusing the snapper. The range meter snapsinto position for carrying and easily detach-es when needed.3.10 PDA 70 measuring extensionThe measuring extension is made from alu-minium and is equipped with a nonconduc-tive plastic grip.The range meter attaches to the measuringextension with the help of the belt clip. The rear reference is then extended by1.270 m/50 inches. Please also refer tosection “7.Operation” for more informa-tion on how to change the reference settingwhen using the measuring extension.3.11 PDA 66 holder The PDA 66 holder joins the PDA/MDA andPD 38 as one unit. The smaller part can beattached to a solid surface on the rear ofthe PDA/MDA. The PD 38 can then beclipped into the holder.
4. Technical data4. Technical dataPower supply3V DC Type: AA (LR6, AM3, Mignon)Standard: two alkaline batteriesOptional: rechargeable NiMh batteriesBattery status indicatorBattery display with four segmentsshowing 100%, 75%, 50% and 25%chargedAll segments deleted = dischargedbatteryMeasuring range0.05 m to 200 m (2 in to 600 ft)0.05 m (2 in) from the front edgeMax. distance resolution 750 m(2,500 ft)Typical measuring range without tar-get plate:– Drywall panel, white 70 m (210 ft)– Concrete, dry 50 m (150 ft)– Brick, dry 50 m (150 ft)The maximum range depends on:– Reflectivity of the target surface– Ambient light conditionsIn case measurements are not possi-ble, use the Hilti PDA 50 target plate. Accuracy ±1.5 mm (±1/16 in) is typical forindividual and continuous measure-ments **** The measuring accuracy is affectedby ± (1.5 mm + 20 ppm)/± (1/16 in+20 ppm) due to atmospheric condi-tions. This effect is typically noticeableat distances > 100 m (> 300 ft).Smallest unit displayed1 mm (1/16 in)Beam diameter< 6 mm @ 10 m (< 0.2 in @ 30 ft)< 30 mm @ 50 m (< 1.2 in @ 150 ft)< 60 mm @ 100 m (< 2.4 in @ 300 ft)Basic operating modesSingle measurementContinuous measurementCalculation/functionsDisplayIlluminated liquid-crystal display showing operating status and batterystatusLaserVisible, 620–690 nm, laser class 2(IEC60825-1: 2003,CFR 21 § 1040 [FDA]) output power: < 1 mWAutomatic time-outLaser: 1 min.Range meter: 10 min.Battery life at 25 °C (77 °F)Max. number of measurements with single set of batteries (laser switched on for 10 sec.)Alkaline: 8,000–10,000NiMH: 6,000– 8,000Operating temperature–10 °C…+ 50 °C (14 °F… 122 °F)Storage temperature–30 °C…+ 70 °C (–22 °F… 158 °F)Protection classDust and splash-proof, IP 54 as per IEC529 standardWeight220 g/0.48 lb (without batteries)Dimensions120 (L) x 65 (W) x 28 (H) mm4.7" (L) x 2.5" (W) x 1.1" (H) in8
95. Safety information5. Safety information5.1 Basic safety informationIn addition to the safety precautions listedin the individual sections of these operatinginstructions, the following points must bestrictly observed at all times.5.2 MisuseThe range meter and its accessories can bea source of hazard if they are not usedproperly or not used for the intended pur-pose by untrained people.– Do not use the range meter without suit-able prior instruction.– Do not render any safety devices ineffec-tive and do not remove information andwarning notices. – Have the range meter repaired only at aHilti service center. Unauthorized open-ing of the range meter may cause theemission of laser radiation in excess ofclass 2.– Tampering with or modification of therange meter is not permissible.– Use only genuine Hilti accessories andauxiliary tools in order to avoid the riskof injury.– Do not use the range meter in atmos-pheres where there is a risk of explosion.– Use only a clean, soft cloth for cleaning.If necessary, moisten the cloth slightlywith pure alcohol.– Keep the range meter out of the reach ofchildren.– Measurements taken to plastic foammaterials, such as polystyrene foam, orto snow or other strongly reflecting sur-faces, may be inaccurate.– Taking measurements to surfaces withlow reflectivity surrounded by areas withhigh reflectivity may lead to measure-ment errors.– Measurements taken through panes ofglass or other objects may be inaccurate.– Rapid changes of the measuring condi-tions, e.g. persons walking through thelaser beam, may lead to measurementerrors.– Do not direct the range meter towardsthe sun or other sources of bright light.– Do not use the range meter as a levellingtool.– Check the range meter before takingimportant measurements and after it hasbeen dropped or subjected to othermechanical stressing.– Check the setting of the measuring re-ference before measuring.5.3 General safety precautionsCheck the range meter for possible damagebefore use. If the range meter is found tobe damaged, have it repaired at a Hilti serv-ice centre. The accuracy of the range metermust be checked after it has been droppedor subjected to other mechanical stressing.– When the range meter is brought into awarm environment from very cold condi-tions, or vice versa, allow it to becomeacclimatised before use.– Although the range meter is designed forthe tough conditions of jobsite use, aswith other optical instruments (binocu-lars, spectacles, cameras, etc.) it shouldbe treated with care.– Although the range meter is protected toprevent entry of dampness, it should bewiped dry each time before being putaway in its transport container.– As a precaution, check the settings youhave made before using the range meter.– When using the circular bubble level(bull's eye) for alignment, only look atthe range meter from the side.
105. Safety information5.4 Proper organization of workplace– Secure the area in which you are meas-uring. When setting up the range meter,take care to avoid directing the beamtoward yourself or other people.– Avoid unfavourable body positions whenworking on ladders or scaffolding. Makesure you have a stable stance and avoiddanger of overbalancing at all times.– Measurements taken through panes ofglass or other objects may be inaccurate.– Use the range meter only while observingthe specified operating conditions, i.e.not directed towards a mirror, stainlesssteel, polished stone, etc.– Observe the accident prevention regula-tions applicable in the country in whichyou are working.– Use the PDA 66 holder only together withthe PDAs/MDAs recommended by Hiltiand only in conjunction with the PD 38.– Check to ensure that your PD 38 com-municates only with your PDA/MDA, andvice versa.5.4.1 Electromagnetic compatibilityAlthough the range meter complies withthe strict requirements of the relevantguidelines, Hilti cannot entirely rule out thefollowing possibilities:– The range meter might cause interfer-ence to other equipment, e.g. aircraftnavigational equipment.– The range meter might be subject tointerference caused by powerful radia-tion, which can then lead to incorrectoperation. Check the readings for plausi-bility when measuring in these conditionsor if you are unsure of the results.5.4.2 Laser classificationThe range meter conforms to laser class 2based on the IEC60825-1: 2003; standardand class II based on CFR 21 § 1040(FDA). These range meters may be usedwithout need for further protective meas-ures. The eyelid closure reflex protects theeyes if a person looks into the beam unin-tentionally for a brief moment. The eyelidclosure reflex can, however, be negativelyinfluenced by medication, alcohol or drugs.Nevertheless, as with the sun, a personshould not look directly into sources ofbright light. The laser beam should not bedirected towards persons.Laser information plates based on IEC60825-1: 2003Laser information plates for the US based on CFR 21 § 1040 (FDA)This laser product complies with 21 CFR1040, as applicable.5.4.3 TransportRemove the alkaline or rechargeable batter-ies whenever transporting the range meter.
116. Getting started6. Getting started6.1 Inserting alkaline/rechargeablebatteries-CAUTION-– Observe the polarity of the batteries.(refer to symbols inside the battery com-partment.)– Make sure the battery compartment isproperly locked.1.Press the cover of the battery compart-ment lightly.2.Slide the cover out and off.3.Replace the batteries.-NOTE-For alkaline batteries– Always replace a complete set of batter-ies.– Do not mix used and new batteries.– Do not mix batteries of different makesor types.– Use only undamaged batteries of anapproved type.For rechargeable batteries– Always use rechargeable batteries of thesame make and same type.– Always use rechargeable batteries of thesame age and charged to the same level.– New rechargeable batteries are supplieduncharged and have to be charged priorto first use.– Use only 1.2 V NiMH batteries with1500–2000 mAh capacity.6.2 Battery charging6.2.1 Standard battery chargingThe charging process ensures that therewill be virtually no “memory effect”. Inview of this, charging can begin at any timeregardless of the level to which the batteryis already charged.Attach the PDAW 80/81-1 charging adapterto the range meter ቢ.For charging, connect either the mainsadapter or the car battery plug ባ to the charging adapter.The maximum charging time is 12 hours.As with many mobile phones, the level ofcharging is shown by movement of batterydisplay segments.122
126. Getting started6.2.1.1 Battery charging level display– The level of charging is indicated bymoving battery status segmentsat top right of the display.– When a battery is fully charged, (battery fully charged) will be dis-played.6.2.1.2 Charging display for unintention-ally inserted alkaline batteries – If alkaline batteries are identified, all bat-tery status segments flash continually toindicate missing rechargeable batteries.Additionally, the symbolshows in the display.The range meter cannot be switched on.– If defective or non re-chargeable alkalinebatteries are inserted, the battery displaywill flash and, at the same time, (defective battery) will appear inthe display.-NOTE-– The range meter can be switched on andused at any time while the batteries arebeing charged. The battery chargingprocess stops when the range meter isswitched on and the laser activated.– Rechargeable batteries discharge if theyare stored for a long time. The batterycharging process terminates after1minute when charging deeply dis-charged or defective rechargeable batter-ies and the display switches off. In thiscase, the charging process can be re-started only by disconnecting the rangemeter from the mains adapter or byremoving/replacing the rechargeable bat-teries.– Keep the range meter in a safe place.dEFAccuAccunoFullAccu6.2.2 Fast battery chargingThe charging process ensures that 15 min-utes of charging with the PDAW 80/81-2car battery plug provides the battery withenough power for a further 150 to 200measurements.This process in combination with the carbattery plug is of particular advantage insituations where the user needs the rangemeter ready for use quickly.6.3 Switching the range meter on and offThe range meter is switched on or off bypressing the “On/Off” button.After switching on, the range meter is inthe basic display mode.6.3.1 Initial distance measurementPress the “Measure” button once.This will switch on the range meter and thelaser beam if the range meter was prvious-ly switched off.If the range meter is already switched on,this will activate the laser beam.Aim the visible laser spot at a target about3 to 10 (10–30 ft) meters away.Press the “Measure” button again.The distance will be shown in less than1second, e.g. 5.489 m (16.296 ft).You have taken the first distance measure-ment with the PD 32 range meter.m5.489
136. Getting started6.4 Settings6.4.1 Activating the settings menuThe menu is activated by pressing the“On/Off” button for about 2 seconds whilethe range meter is switched off.The menu allows beep, units and Bluetoothsettings to be made.6.4.2 Menu/BeepThe “Plus” button is used to switchbetween the “On” and “Off” modes.Setting OptionBeep OnOff6.4.3 Menu/UnitsThe “Minus” button is used to switchbetween the units, as shown below.Setting Distance Area Volumemmeters m2m3mm millimeters m2m3ft feet (decimal) feet2feet2yd feet (decimal) yard2yard3in inch (decimal) inch2inch3in 1/8 feet & inch 1/8 feet2feet3in 1/16 feet & inch 1/16 feet2feet36.4.4 Switching Bluetooth on and offThe menu must be activated with the“ON/OFF” button beforehand. Refer to“6.4.1. Activating the settings menu”.The volume button toggles Bluetoothbetween ON and OFF.The symbol shows the Bluetooth on-status. Buetooth is switched off when thissymbol is not displayed.The symbol indicates an active con-nection to a PDA/MDA running the HiltiPD 38 software.-NOTE-The PD 38 connects only to devices run-ning the Hilti PD 38 measuring applicationon the Windows CE operating system orwherever a Hilti Bluetooth interfacing ver-sion is installed and active (typicalPDA/MDA).6.4.4 Terminating the menuThe menu is terminated by pressing the“On/Off” button. All settings displayed willbe saved.BeepUnitsMENUonmBEEPUnitMENUonmBEEPUnitBluetooth switched onMENUonmBEEPUnitBluetooth switched off
7.1.3 Measuring extension as reference–Tool is switched off.Press the measuring reference button and the +on/off button simultaneously.+The measuring spike flashes in the display. The referenceis then set to the end of thefully extended measuringextension.7.1.3 Measure buttons“Measure” button–switches the range meter on–activates the laser beam foraiming at the target,–activates single distancemeasurement –activates and deactivates con-tinuous distance measure-ment.Side “Measure” button–activates the laser beam foraiming at the target,–activates individual distancemeasurement –activates and deactivates con-tinuous distance measure-ment.7.1.4 Function buttonsCalculation functions are activated bypressing the relevant function buttons.When a measurement using a function hasbeen carried out incorrectly or unintention-ally, the function can be reset at any timeby pressing the same function button againor any other function button.Volume–activates the “volume” function and deactivates every other function.147. Operation7. Operation7.1 General controls7.1.1 Control panel7.1.2 On/off and control buttonsON/OFF–switches the range meter on and off.Measuring reference point–switches the measuring reference between front and rear.Display illumination–switches the display illumination on and off.
157. OperationArea–activates the “area” function and deactivates every otherfunction.Plus–activates the “distance addition” function and deacti-vates every other function.Minus–activates “distance subtraction” and deactivatesevery other function.7.2 DisplayThe display shows the measurements, set-tings and range meter status.In the measuring mode, the latest readingsare shown in the lowest display line (resultline) and the prior readings in the linesabove. For functions such as area, volume,Pythagoras, etc., the measured distancesare displayed in the intermediate lines andthe calculated result appears in the lowestdisplay line (result line).m27.3175.489mmm12.34924.6347.2.1 Symbols displayedTemperature too high> +50 °C (122 °F)Action:Allow the range meter to cooldown.Temperature too low< –10 °C (14 °F)Action:Warm up the range meter.Unfavourable signal conditionsInsufficient reflected laser lightAction:– Observe the minimum measu-ring distance of > 50 mm(2 in) from the front edge.– Clean the lens.– Take a measurement fromanother surface or use thePDA50 target plate.Ambient light at target too brightAction:– Shade the target from brightlight or use the PDA50 tar-get plate.Laser switched on– Moving broken lineDisplay reference status– Front edge– Rear edge– Spike– Spike (flashing) – automati-cally adds 1.270 m/50 inchesto measurementsBattery status– 4 segments =100% fully charged– 3 segments = 75% – 2 segments = 50% – 1 segment = 25% – 0 segments = discharged
167.2.2 Display illumination= Illumination buttonThe illumination button switches the dis-play illumination on or off. In the dark or invery bright light, e.g. sunlight or a strongspotlight, the display illumination makes iteasier to read the display.-NOTE-Display illumination consumes additionalpower. If it is used frequently, shorter bat-tery life must be expected.7.3 Optical sightThe built-in optical sight is of great benefitwhen measuring outdoors and wheneverthe laser spot is poorly visible. The opticalsight allows the laser spot to be positionedon the target accurately even at great dis-tance. The laser spot is visible in the opti-cal sight when the range meter is switchedon. If the laser spot is not visible in theoptical sight then either the measurementhas been completed successfully or thelaser beam has switched itself off automat-ically after the preset time (1 minute).The optical axis of the sight runs parallel tothe laser beam.Typical measuring procedure with theoptical sight– Press the “Measure” button to activatethe laser beam.– Use the optical sight to aim the rangemeter and position the laser spot on thetarget.–Press the measure button or side mea-sure button and keep the laser spot onthe target until the spot disappears fromthe optical sight.– Read the distance from the display.7. OperationBatteries fully dischargedAction:–Replace batteries.– Recharge rechargeablebatteries.Menu activatedBluetooth is switched onBluetooth has establishedconnection to another deviceHistorical data mode active– Displays the previous 5 measurements or completefunctions results includinggraphics.General hardware errorSwitch the range meter offand then back on. If the errorpersists, notify the local Hiltiservice centre.Volume measurement activeArea measurement active
7. OperationDiagram of optical sight-NOTE-Use of the optical sight is recommendedfor distances above 10 m (30 ft.).7.4 Measuring distancesDistance measurements can be taken to allstationary targets without a highly reflec-tive surface, i.e. concrete, rock, wood,plastic, paper, etc. The use of prisms ormeasuring to highly reflective surface isnot permitted and, if attempted, might fal-sify the results.7.4.1 Measuring references= Reference buttonThe range meter can measure distancesfrom three different measuring referencepoints.The measuring reference point can be tog-gled between the front edge and rear edgeby pressing the reference button on frontleft of the range meter. The reference is setautomatically to the end of the spike whenthe spike is folded out to the 90° position.The reference can be set to the end of thePDA 70 measuring reference extension bypressing the reference button (top left) andthe on/off button (top right) simultaneouslywhile the range meter is switched off. Thespike symbol in the display then begins toblink.This measuring reference setting for thePDA 70 can be deactivated by switchingthe range meter off and then on again.EyeLaser SightingDisplay Reference positionFront edgeRear edgeEnd of spikePDA70 measuring extensionSpike (flashing) extends by1.270 m/50 inches-NOTE-– If the spike is folded out 180°, the refer-ence point is always automatically set tothe rear edge.7.4.2 Measuring distances step by stepThe range meter measures distances in avery short time and, when doing so, showsvarious information in the display.1. Switch on the range meter by pressingthe “On” button.2. Press the “Measure” button once. This switches on the red laser beamwhich is visible as a laser spot on thetarget surface. The display shows thisaiming mode as an animated broken line. ----------mLASERm----------17
187.4.3.1 Single distance measurement(“Measure”)1.Switch on the laser beam by pressing the “Measure” button.2.Press the “Measure” button once again.The measured distance will normally beshown in the result line in less than asecond.-NOTE-Alternatively, the range meter may beswitched on by pressing the “On” buttonand the laser then activated by pressing the“Measure” button.7.4.3.2 Continuous measurementPress the “Measure” button for about2seconds to activate this measuring mode.When doing so, it does not matter whetheror not the range meter or the laser beam isswitched on or off. The range meter willalways switch to continuous measurement.During continuous measurement, distancesare updated in the result line at the rate ofabout 8 to 15 measurements every second.The rate of measurement depends on thereflectivity of the target surface.If the beep signal is active, continuousmeasurement is indicated by a beep. The measuring process is stopped bypressing the “Measure” button once again.On doing so, the last valid distance meas-urement will be shown in the result line inthe display.-NOTE-Continuous measurement is possible in allsituations where distances can be mea-sured. This applies also to functions, suchas areas and volumes.7. Operation3. Aim at the target.4. Press the “Measure” button once againto measure the distance.The result appears in the result line nor-mally in less than a second. The laserbeam switches off.If further measurements are taken, up tothree previously determined distances areshown in the intermediate result lines, i.e.atotal of the last four measured distancesare shown.7.4.3 Measuring modeTwo different distance measuring modesare available. These are single distancemeasurement and continuous distancemeasurement. The continuous measure-ment mode is used for setting out givendistances or offsets and is also used wheredistance measurements are more difficult,e.g. to corners, edges, niches, etc.m27.3175.489mmm12.34924.634m5.489
197. Operation7.4.4 Measuring from cornersThe spike is used when measuring diago-nally across rooms or from inaccessiblecorners.1. Fold out the spike 90°.This automatically sets the measuringreference to the end of the spike. Therange meter takes the extended referencepoint into account and corrects themeasured distances accordingly.2. Position the range meter with the spikeat the desired starting point for themeasurement and aim towards the tar-get.3. Press the “Measure” button. The meas-ured distance appears in the display.7.4.5 Measuring with the aid of targetobjectsWhen taking measurements to outside cor-ners, e.g. on buildings, perimeter fences,etc., boards, bricks or other suitableobjects can be used as the target.Use of the PDA 50 target plate is recom-mended for long distances and in unfa-vourable light conditions, e.g. strong sun-light.7.4.6 Measuring in bright conditionsThe PD 38 has a built-in optical targetsight. When measuring to very bright sur-faces, the laser spot is often not visible.Thanks to the laser spot superimposed inthe optical sight, you can always clearlyand reliably aim at the target.We recommend use of the PDA 50 targetplate for long distances and bright lightconditions.
207.4.10 Taking measurements to transpar-ent surfacesIt is not possible to measure distances totransparent materials, e.g. liquids, poly-styrene foam, etc. This is because lightpenetrates these materials and thereforemeasuring errors may occur. Measuringerrors may also occur if measurements aretaken through glass or if obstructions arepresent within the line of the laser beam. 7.4.11 Measuring ranges7.4.11.1 Increased distances– Taking measurements in the dark, atdawn, dusk and to shaded targets or withthe front of the range meter shaded, gen-erally leads to an increase in the measur-ing range.– Taking measurements to the PDA 50target plate also results in an increase inthe measuring range.7.4.11.2 Reduced distances– Taking measurements in very brightambient light, e.g. in sunshine or a verybright spotlight etc, can lead to a reduc-tion in range.– Taking measurements through glass orother objects in the target beam can leadto reduced measuring range.– Taking measurements to matt green, blueor black, wet or shiny surfaces can leadto reduced measuring range.7. Operation7.4.7 Taking measurements to rough sur-facesWhen measuring to rough surfaces, e.g.coarse render, stucco, etc, an average dis-tance value is measured with the centre oflaser spot weighted higher than the edgesof the laser spot.7.4.8 Taking measurements to round orinclined surfacesIf the laser beam strikes the target surfaceat a very narrow angle, the light reflectedmay be inadequate.Conversely, too much light may be reflect-ed toward the range meter in certain situa-tions where the laser beam strikes the tar-get perpendicularly.We recommend use of the PDA 50 targetplate in both of these situations.7.4.9 Taking measurements to wet orshiny surfacesAs long as the range meter can be aimedtowards the surface, the distance to thetarget will be reliably measured. In the caseof highly reflective surfaces, a reduction inrange or measurement of the distance tothe actual point of reflection must beexpected.
218. Applications and functions8. Applications and functionsThe individual steps within all functions aresupported by the graphical display.-NOTE-– Continuous measurement can be usedwithin all functions where single measure-ments are possible.– If measuring errors occur during conti-nuous measurement or if continuousmeasurement is stopped by pressing the“Measure” button again, the last validdistance will be shown.All PD 38 on-board functions such as area,volume, plus and minus are disabled whilea Bluetooth connection is active.An active connection is indicated by thesymbol.8.1 Measurement data memoryThe range meter continuously saves themeasured values and the results of calcula-tions while measuring.8.1.1 Saving measurementsWhen measuring several distances, up tothree previous distances are displayed inthe intermediate result lines. This meansthat, in total, the last four measured dis-tances are displayed or saved.4. measured value3. measured value2. measured value1. last measuredvalue8.1.2 Historical data memoryThe range meter saves the last five meas-urements or calculations including thegraphics. This saved data can be shownconsecutively in the display by pressing theplus and minus buttons immediately afterswitching on the range meter with theon/off button (as long as no function hasbeen carried out or distance measurementtaken).The symbol “Historical data mode active”shows the data stored in the memory.Example of the display of a saved volumemeasurement:8.2 Area measurement Areas can be determined easily and quickly.Press the “Area” function button. Thisswitches the laser beam on – ready formeasuring.The individual steps for determining an areaare supported by a corresponding graphicdisplay. To determine the floor space of aroom, for example, the procedure is as fol-lows:ab= a . bm1669.7835.489mmm12.34924.6343M+
22The individual steps for determining a vol-ume are supported by a correspondinggraphic display. To determine the volumeof a room, for example, the following pro-cedure must be followed:1. At the start of the volume function, thelaser beam is switched on. 2. Aim the range meter towards at the tar-get.3. Press the “Measure” button.The room width will be measured andshown.4. After this, the graphic display will auto-matically request measurement of theroom length.5. Aim the range meter at the next targetto obtain the room length.6. Press the “Measure” button.The room length will be measured.7. After this, the graphic display will auto-matically request measurement of theroom height.8. Aim the range meter at the next targetto obtain the room height.9. Press the “Measure” button.The room height will be measured, thevolume immediately calculated and theresult shown in the result line.All three distances required to calculate thevolume appear in the intermediate resultlines and can be conveniently noted afterthe measurements and the calculation.-NOTE-To determine another volume, press the“Volume” function button again. m1669.7835.489mmm12.34924.63438. Applications and functions1. At the start of the area function, thelaser beam is switched on.2. Aim the range meter at the target.3. Press the “Measure” button.The room width will be measured andshown.4. After this, the graphic display will auto-matically request measurement of theroom length.5. Aim the range meter at the next targetto obtain the room length.6. Press the “Measure” button.The second distance will be measured,the area immediately calculated and theresult shown in the result line.Both distances required to calculate thearea appear in the intermediate result linesand can be conveniently noted after themeasurements and the calculation.-NOTE-To determine another area, press the“Area” function button again.8.3 Volume measurement Volumes can be determined in one measur-ing operation.Press the “Volume” function button. Thisswitches the laser beam on – ready formeasuring.MENx+-I=PD 25m67.7845.489mm12.3492
238. Applications and functions8.4 Adding distancesIndividual distances can be convenientlyadded. This is useful for determining thetotal length of the inner face of door orwindow openings or for adding severalpartial distances that form a perimeter. 1. Press the “Measure” button.(The laser beam will be switched on).2. Direct the range meter towards the tar-get.3. Press the “Measure” button.The first distance will be measured andshown. (The laser will be switched off.)4. Press the “Plus” button to add the nextdistance. The first distance will appearin the middle (intermediate) result lineand a plus sign in the lower line. (Thelaser beam will be switched on.)5. Aim the range meter at the next target.6. Press the “Measure” button.The second distance will be measuredand shown in the lower (intermediate)result line. The calculation result willappear in the result line at the sametime.The current total of the distances is alwaysshown in the result line.This procedure can be repeated until alldistances have been added.17.838mm12.349+5.489mMENx+-I=PD 25MENx+-I=PD 25MENx+-I=PD 25MENx+-I=PD 25MENx+-I=PD 25MENx+-I=PD 25To terminate the addition of distances, sim-ply measure a distance without first press-ing the “Plus” button. The previous threemeasurement and calculation results willbe shown in the intermediate displays.8.5 Subtracting distances Individual distances can be convenientlysubtracted from each other. This is usefulfor determining, for example, offsets toinaccessible places or the distance fromthe underside of a pipe to the ceiling. Todo so, the distance from the floor to theunderside of the pipe is subtracted fromthe distance from the floor to the ceiling. If,additionally, the pipe diameter is deducted,the result is the distance from the top ofthe pipe to the ceiling.1. Press the “Measure” button.(The laser beam will be switched on.)2. Aim the range meter at the target.3. Press the “Measure” button.The first distance will be measured andshown. (The laser beam will switch off.)4. Press the “Minus” button for subtrac-tion.The first distance will appear in themiddle (intermediate) result line and aminus sign in the lower line. (The laserbeam will switch on.)5. Aim the range meter at the next target.6. Press the “Measure” button.The second distance will be measuredand shown in the lower (intermediate)result line. The result of the subtractionwill appear in the result line.879546213.0=CIPD 28?!+x879546213.0=CIPD 28?!+x?
8.6 Setting out Predetermined dimensions, such as forinstalling drywall tracks, can be set out andmarked with the range meter.The continuous measurement mode isused when transfering dimensions fromdrawings. (See also section 7.4.3.2 “Con-tinuous measurement.”)Hold the “Measure” button pressed forapprox. 2 seconds to activate the continu-ous measurement mode. When doing so, itdoes not matter whether the range meteror the laser beam are switched on or off.The range meter always switches to thecontinuous measurement mode. Move therange meter slowly until the desired dis-tance is reached or appears in the display.Press the “Measure” button once again toend the continuous measurement mode.248. Applications and functionsThe current difference between dis-tances is always shown in the resultline.This procedure can be followed until alldistances have been subtracted.To terminate the subtraction of distances,simply measure a distance without firstpressing the “Minus” button. The previousmeasurement and calculation results willbe shown in the intermediate displays.0.625mm3.947-3.322m
259. Measuring using a Bluetooth connection-NOTE-Only PDAs/MDAs running the Windows CEoperating system are compatible with thePD 38.9.1 Setting up the PDA/MDAIf you intend to use a new PDA/MDA out ofthe box for the first time with a PD 38, it isrequired to first connect the PDA/MDA tothe PC. Please follow the user instructionsfor the PDA/MDA which describe how tomake a PC connection and how to set upthe PDA/MDA for data exchange with a PC.Section 9.1.1 can be used as a generalguideline. Please refer to the instructionssupplied with your PDA/MDA for moredetailed information.If your PDA/MDA running the WindowsCE operating system is already set up fordata exchange using “Active Sync”, pleasego to section 9.2 “Establishing a connec-tion between PDA/MDA and PD 38”.9.1.1 Installation and connection ofPDA/MDA and PC General step-by-step instructions for con-necting a PDA/MDA and a PC:1. The CD-ROM supplied with the PDA/MDAcontains the Windows connection soft-ware Active Sync. Install this softwareon the PC in accordance with the instruc-tions of the PDA/MDA manufacturer.2. Connect the PDA/MDA docking stationto the PC with a USB cable.3. Place the PDA/MDA in the docking sta-tion and switch it on.4. Active Sync should activate itself auto-matically on the PC after the PDA/MDAhas been placed in the docking stationand switched on. Alternatively, ActiveSync can be started manually on the PC.9. Messen mit Bluetooth-Verbinduung5. Follow the instructions of “Active Sync” toestablish a guest partnership with the PC.-NOTE-Read the instructions for the PDA/MDAcarefully about setting up the connection tothe PC using the Windows software “ActiveSync”.9.1.2 Installation of Hilti PD 38 applicationsoftware on a PDA/MDA Installation of Hilti PD 38 application soft-ware on a PDA/MDA:Before beginning the installation, it isessential that the connection between thePDA/MDA and the PC has been establishedby installing the Active Sync Windows PCsoftware.1. Place the PDA/MDA in the docking sta-tion and switch it on.2. Follow the instructions of “Active Sync” toestablish a guest partnership with the PC.3. Insert the Hilti PD 38 CD-ROM in theCD-ROM drive. The installation will startautomatically.Please follow the instructions on thescreen.Remove the PDA/MDA from the dockingstation after successful installation of theHilti PD 38 application software.9.2 Establishing a connection betweenPD 38 and PDA/MDABefore the connection can be established itis essential that the Hilti PD 38 applicationsoftware has been successfully installed onthe PDA/MDA.1. Switch on the PD 38 by pressing the“On” button . Check that the sym-bol is displayed. If this symbol is notdisplayed, check that Bluetooth isswitched on (refer to section 6.4.4“Switching Bluetooth on and off”).
269. Measuring with a bluetooth connection2. Switch on the PDA/MDA and proceed asfollows:– Select Windows Start– Select Programs– Select the Hilti PD 38 symbol The Hilti PD 38 application then startswith the following screen:A search for all nearby Hilti PD 38 laserrange meters with active Bluetooth modewill start as soon as the above screen isshown. The search can take up to 2 minu-tes. The displayed list shows the serialnumbers of all PD 38s found. Select theserial number of your PD 38. The serialnumber can be found on the back of thePD 38. Press the button to make theconnection.The connection is established after approx-imately 30 seconds. The symbol pro-vides verification of a successful connec-tion.3. On successful connection betweenPDA/MDA and PD 38 the display of thePDA/MDA changes to the start-up dis-play of the Hilti PD 38 applications andshows the serial number of the connec-ted PD 38 in the lower window.9.3 Measuring using Bluetooth connec-tion to PDA/MDA -NOTE-During an active Bluetooth connection allPD 38 on-board functions such as area,volume, plus and minus are disabled. Thesymbol indicates an active Bluetoothconnection.Distance measurement functions using thePDA/MDA are shown either with theicon or with the icon.Distance measurement can always be trig-gered from the PDA/MDA if one of abovesymbols is available or by pressing themeasuring button on the PD 38 laserrange meter.Hilti PD 38 15805701
10. PDA/MDA Windows CE application Hilti PD 38 10. PDA/MDA Windows CE withHilti PD 38 applicationThe Hilti PD 38 application is installed on aPDA/MDA as described in chapter “9.1.2Installation of Hilti PD 38 application soft-ware on a PDA/MDA”. The program con-tains four major functions, Image Sketch,Line Draw, Data Table and Formulary. Themeasurements are transferred to the par-ticular function by wireless communication– all measurements can also be enteredmanually.-NOTE-Further instructions about the separatefunctions can be found in the help texts forthe particular function on the PDA/MDA.1. “Image Sketch” Some PDAs and most MDAs are equip-ped with a digital camera which allowsphotos to be taken of a particular objecton the spot, e.g. window, door, room, etc.Existing digital images can also be trans-ferred to the PDA/MDA. Measuredlengths, shown as lines with dimensions,can be added directly to the photostaken on the spot with the PDA/MDA orthose transferred from the PC.These photos with measurements canthen be printed out or transferred to thePC for further use.Using an MDA, the photos can be sentas an E-mail from the photo location, forexample, to an office.All relevant output formats, e.g. bitmap(*.bmp) or JPEG (*.jpg) can be trans-ferred to the PC.2. “Line Draw” This drawing function creates outlineplans – combining measuring and scaledrawing – on the spot.Other possible uses are the design anddrawing of non-rectangular objects andfeatures.The calculation of the area of enclosedgeometrical figures is also possible, evenwhen several are joined together.All common CAD output formats are supported for transfer to the PC– Felixcad (*.flx)– AutoCad DXF (*.dxf) for release 12 up torelease 14 and AutoCad 2000/2002– AutoCad Format (*.dwg) for release 12up to release 14 and also AutoCad2000/2002All drawings can also be transferred aspixel data to the PC– Bitmap (*.bmp)– JPEG (*.jpg)This allows the drawings to be displayedon a PC without a CAD system.3. “Data Table” The Data Table function creates a table fullycompatible with Windows Excel, withmeasurements entered directly in theappropriate cells.However, measurements are activated(from the PDA/MDA or from the PD 38)only when the “Hilti Measuring Interface”in the lower right-hand window has beenactivated.Once active, the symbol is shown inthe lower section of the PDA/MDA display.-NOTE-Take note of the units used in Excel asthese are not saved.27
10. PDA/MDA Windows CE application Hilti PD 38/11. Data transfer from PDA/MDA to PCDifferent options exist when using thedata table– The data table can be used with the cellssimply containing measurements, with-out any line or column description.– The structure of the table can be estab-lished on the PDA/MDA, i.e. the lines andcolumns are pre-defined according to themeasurement needs and the measure-ments entered into the respective cells.– The structure of the table can be definedand established in Windows Excel on thePC, i.e. a relevant structured measure-ment table fully pre-defined on the PC.This can also contain formats and formu-las which can be used as checks on thespot.-NOTE-Measurements initiated from the PD 38 aredisplayed on the PDA only when the HiltiMeasuring Interface is active.On completion of the measurements, thetable can be transferred to the PC for fur-ther use.4. “Formulary” .The functions of the formulary serve toassist with less common measuringtasks, e.g. measuring length at inacces-sible places, angle and area determina-tions of non-rectangular areas and muchmore …Measurements are transferred directly tothe relevant location within the function.Measurements can also be entered man-ually. The user is guided step by step bythe graphical user interface.List of functions:– Area computations– Volume computations– Indirect distance measurement usingPythagorean function (3 options)– Circle computations (area and circumference)– Inclination computations (roof slope,pipe slope, etc … in inaccessible places)– Minimum and maximum measurementsfor diagonals and much more– Average computations from eight con-secutive measurements Computation results can be copied for fur-ther use in other programs, as far as thisoption exists.11. Data transfer from PDA/MDA to PC Data is transferred between the PDA/MDAand the PC using the Windows Active Syncsoftware. It is essential that Active Sync ispreviously installed on the PC and a con-nection established between the PDA/MDAand the PC.The exchange of data files between the PCand PDA/MDA is carried out using the“Copy” and “Insert” functions.The data must be saved in the correct for-mat before it can be transferred from thePDA/MDA to the PC.– Data from “Image sketch” must be savedin an appropriate folder in the *.bmp or*.jpg format.– Data from “Line draw” must be stored inone of the many optional data formats.– Data from “Data table” is already savedin the Windows Excel *.xls format.28
2911. Data transfer from PDA/MDA to PC/12. Data transfer from PDA/MDA to PCExample of data transfer from PDA/MDAto PC1. Place the PDA/MDA in the docking sta-tion and switch it on.2. For access to the data memory in thePDA/MDA select “File” and then“Search” in the Active Sync window.3. The complete contents of data memoryin the PDA/MDA are then displayed.4. Select the applicable folder and then thefile to be transferred to the PC.5. Mark the file and then select “Copy”.6. Select the applicable PC drive, e.g. drive“C:” from the bar at the top of the ActiveSync window.7. Then select the folder on the PC driveinto which the file from the PDA/MDA isto be transferred.8. Select “Insert” and the applicable filewill then be transferred from the PDA/MDA to the PC.The procedure for transferring data fromthe PC to the PDA/MDA is very similar, themain difference being that the file is firstselected on the PC before being transferredto the PDA/MDA.12. Calibration and adjustment12.1 CalibrationInspection and testing of the range meterfor users (companies) certified in accor-dance with ISO 900X...You may carry out the inspection, and test-ing of the PD 38 laser range meter asspecified in ISO 900X... by yourself. (SeeISO 17123-4 Field Process for AccuracyExaminations of Geodetic Instruments:Part 6, Close-range Opto-electrical RangeMeters.)Select a readily accessible measuring dis-tance of a known length approx. 1 to5meters (3–15 ft) long which does notvary with time and take five measurementsof the same distance.Determine the mean of the deviations tothe known distance. This value should bewithin the specific accuracy tolerance forthe range meter.Keep a record of this value and note thetime for the next test.Repeat this check measurement at regularintervals as well as before and after impor-tant measuring tasks.Apply a sticker to the PD 38 documentingthis control of the measuring, inspectionand test equipment for the range meter andkeep a record of the entire control process,inspection procedure and the results.Please refer to the technical data containedin the operating instructions and the infor-mation concerning measuring accuracy.
3012. Data transfer from PDA/MDA to PC/13. Care and maintenance12.2 AdjustmentFor optimum accuracy, have the laserrange meter adjusted at a Hilti workshopwhere accurate adjustment of the rangemeter will be confirmed with a calibrationcertificate.12.3 Hilti calibration serviceWe recommend that you undertake a regu-lar check of the laser range meter throughthe Hilti calibration service in order to veri-fy its reliability in accordance with stan-dards and legal requirements.The Hilti calibration service is available atall times, but a check at least once a year isrecommended.As a part of the Hilti calibration service, itis verified that on the day of the check thespecifications of the range meter complywith the technical information given in theoperating instructions.If there are deviations from the manufac-turer's specifications, the range meter willbe re-adjusted. After the check and adjust-ment, a calibration sticker will be applied tothe range meter and it will be verified inwriting in a calibration certificate that therange meter functions in compliance withthe manufacturer's specification.Calibration certificates are always requiredfor companies certified in accordance withISO 900X...Your local Hilti contact/representative willbe pleased to provide further information.13. Care and maintenance13.1 Cleaning and drying– Blow dust off the lens.– Do not touch the lens with your fingers.– Use only a clean, soft cloth for cleaning. If necessary, slightly moisten the clothswith pure alcohol or a little water.-NOTE-– Do not use any other liquids as thesemight damage the plastic parts.– Observe the temperature limits whenstoring your equipment. This is particu-larly important in winter or summer,especially if the equipment is kept insidea vehicle (storage temperatures: –30 °Cto +70 °C/–22 °F to +158 °F).– Replace damaged parts.13.2 Storage– Remove the range meter from its case ifit has become wet. Clean the rangemeter, carrying case and accessories.Re-pack the equipment only when it iscompletely dry.– Check the accuracy of the equipmentbefore it is used after a long period ofstorage or transportation.– Remove the batteries if the range meteris not going to be used for a consider-able time. The range meter can be dam-aged by leaking batteries.13.3 TransportationUse either the original Hilti cardboard boxthe tool was delivered in or packaging ofequivalent quality for transporting or ship-ping your equipment.-NOTE-Always remove the batteries before ship-ment.
3114. Disposal/15. Warranty15. WarrantyHilti warrants that the product supplied isfree of defects in material and workman-ship. This warranty is valid as long as theproduct is operated and handled correctly,cleaned and serviced properly and inaccordance with the Hilti operating instruc-tions, all warranty claims are made within12 months from the date of the sale(invoice date), and the technical system ismaintained. This means that only genuineHilti consumables, components and spareparts may be used in the product. Thiswarranty provides the free-of-charge repairor replacement of defective parts only.Parts requiring repair or replacement as aresult of normal wear and tear are not cov-ered by this warranty.Additional claims are excluded, unlessstringent national rules prohibit suchexclusion. In particular, Hilti is not obli-gated for direct, indirect, incidental orconsequential damages, losses orexpenses in connection with, or by rea-son of, the use of, or inability to use theproduct for any purpose. Implied war-ranties of merchantability or fitness for aparticular purpose are specificallyexcluded.Send the product and/or related partsimmediately upon discovery of the defectto the address of the local Hilti marketingorganization for repair or replacement. This constitutes Hilti's entire obligationwith regard to warranty and supersedes allprior or contemporaneous comments andoral or written agreements concerning war-ranties.14. Disposal-CAUTION-Improper disposal of the equipment mayhave serious consequences:Burning plastic parts/components gener-ates toxic fumes which may present ahealth hazard.Batteries might explode if damaged orexposed to very high temperatures. Thiscould cause poisoning, burns, acid burns orenvironmental pollution. Careless disposalmight permit unauthorized and improper useof the equipment, possibly leading to seriouspersonal injury, injury to third parties and pol-lution of the environment.Most of the materials from which Hiltirange meters are manufactured can berecycled. A prerequisite for recycling isproper separation of the materials. In manycountries, Hilti has already made arrange-ments for old range meters (and othertools and machines) to be taken back forrecycling. Ask Hilti customer service oryour local Hilti representative for furtherinformation.Dispose of batteries inaccordance with national regula-tionsOnly for EU countriesDisposal of electric tools together with household waste is not permissible!In observance of European Directive2002/96/EC on waste electrical and electron-ic equipment and its implementation inaccordance with national law, electric toolsthat have reached the end of their life mustbe collected separately and returned to anenvironmentally compatible recycling facility.
3216. FCC statement (applicable in US)-WARNING-This equipment has been tested and hasbeen found to comply with the limits for aclass B digital device, pursuant to part 15of the FCC rules.These limits are designed to provide rea-sonable protection against harmful interfer-ence in a residential installation. Thisequipment generates, uses, and can radiateradio frequency energy and, if not installedand used in accordance with the instruc-tions, may cause harmful interference toradio communications. However, there isno guarantee that interference will notoccur in a particular installation. If thisequipment does cause harmful interferenceto radio or television reception, which canbe determined by turning the equipment onand off, the user is encouraged to try tocorrect the interference by one or more ofthe following measures:– Re-orient or re-locate the receivingantenna.– Increase the separation between theequipment and receiver.– Connect the equipment to an outlet on acircuit different from that to which thereceiver is connected.– Consult the dealer or an experiencedTV/radio technician for assistance.This device complies with Part 15 of theFCC Rules and RSS-210 of IC. Operation issubject to the following two conditions:1. this device may not cause harmful inter-ference, and2. this device must accept any interferencereceived, including interference that maycause undesired operation.16. FCC statement (applicable in US)
3317. Troubleshooting/18. Bluetooth declaration of compliance17. TroubleshootingNo connection between PDA/MDA and PCNo connection between PDA/MDA and PD 38 when Hilti PD 38 application is startedHilti PD 38 application softwareestablishes no connection to PD 38 after installationNo measurements transferred but PDA and PD 38 are connectedData is transferred but no longervisiblePDA/MDA doesn’t reactNo measurements in data table•Check the cable connection between docking station and PC•Restart PC•Switch on the PD 38•Switch on Bluetooth on the PD 38•Reduce distance between PDA/MDA und PD 38•Switch off Bluetooth on PDA/MDA and restart HiltiPD 38 application on PDA•Reset PDA •Reset PDA •Switch on the PD 38•Check if PDA is equipped with Bluetooth •Reduce distance between PDA/MDA und PD 38•Check serial numbers to verify connection to theright PD 38•Reduce distance between PDA/MDA und PD 38•Reset PDA •Check the folders where files are stored•Check folder before copying•Reset PDA •Activate “Hilti Measuring Interface”18. Bluetooth declaration of complianceThis product is qualified in accordance withBluetooth identifier B01839.
3419. EC declaration of conformityDesignation: Laser range meterType: PD 38Year of design: 2005In conformance with We declare, on our own responsibility, thatthis product complies with the followingstandards or directives: EN 301489-17; EN 300328 and EN 60950-1; 2001 accord-ing to the stipulations of the directive89/336/EEC.Hilti CorporationMatthias GillnerHead BUMeasuring Systems11/ 2005Dr. Heinz-Joachim SchneiderExecutive Vice PresidentBA Electric Tools &Accessories11/ 200519. EC declaration of conformityProduct information plate

Navigation menu