Head Connection Systems 101-460 FRS transceiver PAWN 101-460 User Manual FCC statement on page 7

Head Connection Systems Ltd FRS transceiver PAWN 101-460 FCC statement on page 7

Contents

FCC statement on page 7

HCSHEAD CONNECTION SYSTEMS LTd.Private Address Wireless NetworkTwo Way Communication System forExtreme Noise EnvironmentPAWN 101-MODEL 460OPERATING MANUALThank you for buying this HCS transceiver.This instruction manual contains important safety and operating instruction.Please read it carefully before using the Headset.HEAD CONNECTION SYSTEMS LTd.112 Soundview Drive, Port WashingtonNY, 11050 - 1750Tel: (516) 944-7559/3 Fax: (516) 944-7556For Extreme Noise Environment
-2-1. PAWN 101-460 (Private Address Wireless Network) was tested and approved according theFCC part 95 for UHF licence free. FCC ID: M5U-101-460DESCRIPTIONPAWN is a two-way, 8 frequencies\ channels, wireless FM transceiver, rechargeable battery operated,built into a highly efficient hearing protection device, developed by HCS for secure voicecommunications in noisy environments. The unit provides intelligible speech in noise levels up to 140dB(A)!.FUNCTIONALITYPAWN allows wireless communication with an optional base-station on the same frequency. Thenoise-suppressing microphone efficiently reduces background noise and improves voice intelligibilityin noisy environments. Transmission can be initiated by manually operating the push-to-talk switch orhands free VOX system.APPLICATIONSThe applications for PAWN are many; Floor shop, Power plants, Forestry, Construction, Quarry, Education and other areas where secure communicationover short distances are essential, in noisy areas.2. OPERATING INSTRUCTIONSSimplified controls make PAWN Headsets easy to use and simple to set-up. A four-position switchselects the operating mode, either VOX /PTT or PTT. Rotary switch controls On/Off/Volume. Four-position rotary switch for easy pre-set frequencies changing.PRODUCT LAYOUT1. Volume and On/Off control foradjusting the volume level in theheadset.2. 4-way switch-VOX/PTT setting withthree alternatives for adjusting VOXcircuit’s sensitivity, to ensure "Hands-Free" correct microphone activationin relation to external noise levels.The PTT position which is activatingvia the ”talk” button.3. Frequency setting, a four -positionpre-set channels.4. Charging socket.5. PTT - ”talk” button for manualtransmission.52143
-3-TRANSMITTING AND RECEIVING:The headset is in receiving mode, when it turned on by the Volume/ On/Off switch.To transmit voice makes sure that the microphone is very close to your mouth (about ½ “) and thewhite dot on the microphone is against your mouth. Push the PTT button or adjust the VOX sensitivityand start talking.After releasing the PTT or when you stop talking in VOX mod, you and all other recipients will hear abeep tone.ADJUSTMENT OF THE VOX SENSITIVITY: • Maximum sensitivity (first VOX level) is appropriate for communication in low noise levels. Alow voice signal will activate the transmission. • The third VOX level (lowest sensitivity) is appropriate for transmissions in high noise levels andrequire an increased voice signal in order to activate the transmitter. The optimum choice ofsensitivity adjustment is dependent upon the actual noise level. • When manual operation of the transmitter is desired, the VOX/PTT switch must be in PTTposition. Press the PTT switch during transmit, release for receiving.NOTE:WHEN TRANSMITTING, YOU SHOULD HEAR YOUR OWN VOICE THROUGH THE SPEAKERS.Should the transmitter not work properly in VOX mode: • Is the VOX sensitivity setting appropriate for the level of your voice? • Is the microphone positioned in close proximity to your mouth? • Is the other user transmitting, or is the VOX sensitivity set so high that the transmitter isconstantly activated? • Are you speaking loud enough?Suggestions for proper operation: • When using VOX mode, speak in a constant flow and avoid silent periods between words. • Inform the other listener when your transmission stops. • When you receive a transmission, the PAWN block VOX transmission, PTT is always available.3. BATTRY MAINTENANCE AND CHARGING PROCEDUREImportant: Before first use charge the battery for 10 hours. 1st. Always charge with power turned off. 2nd. To save battery power, the unit is programmed to self shut-off within 60 min. if no activity,receiving or transmitting is detected. A chirp tone will be herd 30 second before shutdown. 3rd. When the battery is almost empty, A number of alert short tone beep will be heard beforeshutdown, and the red LED light will blink.
-4-Important: For best functionality, remove hair around the ears from under the cushions to improvethe acoustical seal against the head. Eyeglass temples should be as thin as possible and conform closeto the head. Turn on the headset and adjust the volume for best listening level.4. Hard Hat Attachment Slide the hard hat attachment into the hard hat slot and press down until itsnaps into position. When the cups are in either store or ventilationposition, the operating position is accomplished by pressing the cupsagainst the head until the clicking sound indicates that the cups are inoperating position. In order to prevent leakage, ensure that the neither thecup or the suspension touches the hard hat when the cups are in theoperating position.5. HEADSET MAINTENANCE AND USER INFORMATIONPAWN must be worn, adjusted, cleaned and maintained in accordance with the instructions in thismanual. ♦ In order to fully benefit from the superior noise attenuation, wear PAWN 100% of the time you areexposed to noise! ♦ Regularly cleans the outside of PAWN using warm water and a mild detergent. ♦♦♦♦ WORNNING: The unit must not be submerged in water. ♦ Do not store or place PAWN in temperatures exceeding +55 C (13O F). Do not place the unitbehind a car windshield or in direct sunlight. ♦ Certain chemicals may negatively effect this product. The manufacturer can provide furtherinformation. ♦ PAWN and especially the cushions may degrade over time and should be examined regularly toverify that they are not cracked or otherwise damaged. Replacement cushions are available. Forcushion replacement gust pull off the old ones. Snap in the new cushions.Important- If these instructions are not followed properly, the noise attenuation properties andfunctionality of the unit may be negatively effected.
-5-6. TECHNICAL SPECIFICATIONSOperating Distance: Approx. 2800 m (8400 ft) over level terrain.500 - 1500 m (1500-4500 ft) in dense building district depend on the constructions site and RF electronic noiselevel.Frequency Coverage MHz 462.5625 ~ 467.7125 MHz*CTCSS TONE (OPTION) 77 HzAntenna Impedance 50 Ohms UnbalanceFrequency Stability +/-2.5 ppmSignal Type F3E (FM)Power Supply Requirements 3.6V ~ 4.5V DC rechargeable (4.5V standard with 3 AA batteries)Current Consumption@4.5V Transmitting: Approx. 500mA (High Power Receiving: Approx. 100mA Squelched)Operating Temperature -10 to +60 Degrees Celsius 14 to 140 Degrees FahrenheitGround NegativeWeight Approx. 14.5oz. (Batteries Included) 400 gr.TRANSMITTER*Output Power Max 500mW high power, 50mW low power / 10mW ERPEmission Mode F3E (FM)Modulation System Variable Reactance FMMax. Freq. Deviation +/- 2.5KHzSpurious Emission -60dB Or Under Below Carrier LevelMicrophone Dynamic differentialOperating Mode Simplex / half duplexRECEIVERReceiver System Super Heterodyne Dual ConversionSensitivity 12dB SINAD : Less Than -15dBuSquelch Sensitivity Less Than -17dBuIntermediate Frequency 1st IF: 21.7MHz; 2nd IF: 450KHzSelectivity More Than +/- 7.5KHz at -6dBAudio Output No More Than 82 dBASpeaker Impedance 220 Ohms*Can be changed by the userinternallySpecifications are subject tochange without notice orobligation.ATTENUATION:``Tested according to ANSI S3.19-1974Frequency Hz 125 250 500 1000 2000 3150 4000 6300 8000 NRR valueTSQ - ON/OFFON = 462 -467OFF = 433-434ON = HIGHOFF=LOWON = GRP 2OFF=GRP 1
-6-Mean Value dB 16 17.5 26.9 34.2 34.3 36.5 36.9 35.8 36.8Std Deviation dB 2.7 2.3 22 2.9 2.5 2.1 2.5 2.6 3.0 26 dBINFORMATION REQUIRED BY E.P.A.The level of nose entering a person's ear, when hearing protection is worn as directed, is closely approximated by the difference between the A-weightedenvironmental level and the NRRExample:1. The environmental noise level at the ear is 100 dB (A).2. The NRR is 23 decibels (dB)3. The level of noise entering the ear is approximately equal to 77 dB (A).CAUTION: For noise environments dominated by frequencies below 500 Hz. the C-weighted environmental noise level should be used. Improper fit ofthis device will reduce its effectiveness in attenuating noise. Although hearing protectors can be recommended for protection against the harmful effectsof impulse noise, the Noise Reduction Rating (NRR) is based on the attenuation of continuous noise and may not be an accurate indicator of theprotection attainable against impulse noise such as gunfire.NOTE: The Noise Reduction Rating is derived from testing procedures at an independent laboratory and in accordance to acceptable ANSI standards.Actual noise reduction can vary from laboratory results as labelled Protection is maximised when proper protector is selected for application.7. SPARE PARTS AND ACCESSORIESTwo easily replaced cushions and damping pads. The replacement cushions are easily installed with a simple press-and-snap function. It is recommendedthat the hearing protector cushions and damping pads are replaced with 6 month intervals Is in order to guarantee continued good noise attenuation,hygiene and comfort.Clean disposable headset protective pads – Cool II: The ultimate and comfortable alternative when using headsets in dirty environments or in extreme heat. Clean is a disposable hygiene pad that is applieddirectly on the hearing protector cushions. Package consists of 100 pairs of pads.LIMITED WARRANTYTHIS PRODUCT IS WARRANTED AGAINST DEFECTS FOR ONE YEAR FROM DATE OF PURCHASE FROM HEAD CONNECTIONCOMPANY AND AUTHORIZED HEAD CONNECTION FRANCHISEES AND DEALERS. WITHIN THIS PERIOD, WE WILL REPAIR ITWITHOUT CHARGE FOR PARTS AND LABOR. SIMPLY BRING YOUR SALES SLIP AS PROOF OF PURCHASE DATE TO ANY HCS STORES.WARRANTY DOES NOT COVER TRANSPORTATION COSTS. NOR DOES IT COVER A PRODUCT SUBJECTED TO MISUSE ORACCIDENTAL DAMAGE. EXCEPT AS PROVIDED HEREIN, HCS MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIESARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES.Copyright © 1998 HCS Head Connection SystemsPS0460A
-7-PAWN-101 460 FCC ID: M5U-101-460 Manufacturer: HCS Ltd.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including I interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCCRules. These limits are designed to provide reasonable protection against harmful Interferes in a residential installation. This equipmentgenerates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may causeharmful interference to radio communications, However there is no guarantee that interference will not occur in a particular installation. Ifthis equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off andon, the user is encouraged to try to correct the interference by one or more of the following measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected,-Consult the dealer or an experienced radio/TV technician for helps.Changes or modifications to this equipment not expressly approved by the party responsible for compliance (HCS Ltd.) could void the user'sauthority to operate the equipment.

Navigation menu