Hansol LCD B17DF-1 17" LCD MONITER User Manual model

Hansol LCD Inc. 17" LCD MONITER model

manual

  User’s Guide H750D(B17DF) TFT-LCD Monitor Regulatory Information.......................................................................................................................... 2 Introduction Package ....................................................................................................................................................3 The range of control Angle ....................................................................................................................... 3 Connection to Signal Source .................................................................................................................... 4 Controls Front panel ................................................................................................................................................5 Functions .................................................................................................................................................. 5 Adjusting OSD .......................................................................................................................................... 6 HOT KEY ................................................................................................................................................ 11 Power Management Feature............................................................................................................... 12 Standard Signal Table .......................................................................................................................... 12 Specifications ........................................................................................................................................ 13 Pin assignment table D-Sub Mini 15pin connector ...................................................................... 14 Troubleshooting .................................................................................................................................... 15Table of Contents
TFT-LCD Monitor2 Regulatory Information - FCC Information CautionChanges or modifications not expressly approved by the party responsible for compliance could void the user’sauthority to operate the equipment. - Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. - Avis Canadien Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur duCanada. - Energy Star As an ENERGY STAR partner, Hansol Electronics Inc. has determined that this product meets energy Star guidelines for energy efficiency.NoticeThe information contained in this document is subject to change without notice.This equipment has been tested and found to comply with limits for a class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residential installation.This equipment can generates, uses, and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation.If this equipment does cause unacceptable interference to radio and television reception, which can be determinedby turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures.  Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced Radio/TV technician for help.
TFT-LCD Monitor3 Introduction - Package - The range of control AngleLCD MonitorUKU.S.A/CanadaEuropeAustraliaKoreaAC Power CableSignal Cable C D(User’s Guide & etc)Warranty CardCongratulations on your purchase of this top quality color monitor!The items illustrated below are contained in the carton.First, be sure that your carton includes all of them.If any items are missing or damaged, please contact your local dealer or supplier.▲ Forward 3° ▲ Default ▲ Backward 30° How to Adjust the StandStereo Cable(Option)Signal Cable(DVI)(Analog)
TFT-LCD Monitor4. Introduction - Connection to Signal Source <Power Source Connection> <Signal Cable Connection>①① Port for AC power cable.② Port for Audio cable from audio source.③ Port for Head Phone or External Speaker.④ Port for signal cable from DVI signal source.⑤ Kensington Lock.⑥Port for signal cable from analog signal source.②③④ ⑤ ⑥ General For Macintosh Adapter for Macintosh(Optional) Refer to the table on the rear side of the optional Macintosh adapter and adjust DIP switch by the resolution.1. Use 220V or 110 V.(Free Voltage)2. Connect monitor and Signal Source via Signal cable.3. Power on the monitor and computer.4. Connection is finished. Basic Connection
TFT-LCD Monitor5 Controls - Front panel - Functions Power button Power button is located in the lower center of the Front Bezel. You can push the button to trun on/off the power.Power Indicating LED Dark : Power off Green : Normal mode Green blinking : DPMS mode or Check Signal Cable mode.On Screen Display(OSD) Function Button OSD buttons on the front of bezel perform the following functions. SOURCE : Press this button to change Analog/DVI display. MENU/EXIT : Press this button to display menus. if you press this button when OSD is displayed, you can switch display to the previous menu and exit menu. SELECT/AUTO : Press this button, when OSD is not displayed, to perform automatic setting. When OSD is displayed, You can select icons. POWER : Power button. + / , – / : By pressing these button when OSD is displayed, You can move cursor into the menus which you want. After press the SELECT button, you can change gauge level or select submenus. When OSD is not displayed, you can adjust brightness or contrast. VOLUME/MUTE : Press this button for volume control. When Control is displayed, You can control mute by pressing this button. / – BUTTONMENU/EXIT BUTTONSELECT/AUTO BUTTON POWER BUTTON(Power indicating LED) / + BUTTONSOURCE BUTTON VOL/MUTE BUTTON
TFT-LCD 모니터6  Controls - Adjusting OSD MENU – + SELECTInput Source1. Press the MENU button to access main menu.2. Use –,+ to move Input source ICON.3. Press SELECT button into the submenu.Digital Input – + SELECT 1. Use –,+ to move Digital input ICON.2. Press SELECT button to select DVI display.Analog Input – + SELECT Brightness & Contrast MENU – + SELECT1. Press the MENU button to access main menu.2. Use –,+ to move Brightness and Contrast ICON.3. Press SELECT button into the submenu.◈ Input Source Submenu◈ Input Source Submenu1. Use –,+ to move Analog input ICON.2. Press SELECT button to select Analog display.
TFT-LCD 모니터7BrightnessContrast – + SELECT – + Clock Phase – + SELECT – + 1. Use –,+ to move Contrast ICON.2. Press SELECT button to select it.3. Use –,+ to adjust the contrast.1. Press the MENU button to access main menu.2. Use –,+ to move Clock Phase ICON.3. Press SELECT button into the submenu.Horizontal Position1. Use –,+ to move H-Position ICON.2. Press SELECT button to select it.3. Use –,+ to adjust display left or right.1. Use –,+ to move Brightness ICON.2. Press SELECT button to select it.3. Use –,+ to adjust the brightness.◈ Brightness & Contrast Submenu◈ Brightness & Contrast Submenu◈ Clock Phase Submenu MENU – + SELECT – + SELECT – + According to the characteristic of video card, control range can be changed.
TFT-LCD 모니터8Vertical Position1. Use –,+ to move V-Position ICON.2. Press SELECT button to select it.3. Use –,+ to adjust display upward or downward.Clock Phase – + SELECT – +1. Press –,+ to move Clock Phase ICON.2. Use SELECT button to select it.3. Use –,+ to correct fine trembling or Video noise. Clock – + SELECT – + 1. Use –,+ to move Clock ICON.2. Press SELECT button to select it.3. Press – or + to remove vertical noise. (Adjusting clock phase is required after the adjustment of clock.) Color MENU – + SELECT1. Press MENU button to access main menu. 2. Use –,+ to move Color ICON.3. Press SELECT button into the submenu.◈ Clock Phase Submenu◈ Clock Phase Submenu◈ Clock Phase Submenu – + SELECT – + According to the characteristic of video card, control range can be changed.
TFT-LCD 모니터9Preset Color – + MENU 1. Use –,+ to select the 6500K, and 9300K.2. Press the Menu button to return previous state.※ 6500K : Reddish white / 9300K : Bluish whiteUser Color – + SELECT – + MENU1. Use –,+ to move User color ICON.2. Press SELECT button to select it.3. Use –,+ to Shift the color what you want.4. Use select button to select it.5. Use –,+ to increase or decrease each color.6. Press the menu button to return previous state.Special 1. Press MENU button to access main menu.2. Use –,+ to move Special ICON.3. Press SELECT button into the submenu.Language1. Use –,+ to move Language ICON.2. Press SELECT button to select it.3. Use –,+ to select language. MENU – + SELECT – + ◈Color Submenu◈Color Submenu◈ Special SubmenuMENU – + SELECT
TFT-LCD 모니터10 – + SELECT – + – + SELECT – + Factory Reset – + SELECT1. Use –,+ to move the Factory Reset ICON.2. Press SELECT button to return to default setting.Information 1. Use –,+ to move the Information ICON.2. Press SELECT button to select it.OSD H-Position1. Use –,+ to move OSD H-Position ICON.2. Press SELECT button to select it.3. Use –,+ to adjust OSD left or right.OSD V-Position1. Use –,+ to move OSD V-Position ICON.2. Press SELECT button to select it.3. Use –,+ to adjust OSD upward or downward.◈ Special Submenu MENU – + SELECT◈ Special Submenu◈Special Submenu◈ Special SubmenuYou can know display information* Accoding to the characteristic of video card, display information can be incorrect.
TFT-LCD 모니터11 - HOT KEY When change DVI display into Analog display, select source button located in the left. Analog display will be showed after Analog input message. When change Analog display into DVI display, select source button located in the left. DVI display will be showed after DVI input message. No signal input message will be displayed when video card output is not mated with monitor source. OSD Time1. Use –,+ to move OSD Time ICON.2. Press SELECT button to select it.3. Use –,+ to adjust OSD display time. – + SELECT – + Sound(Option)1. Use –,+ to move Sound ICON.2. Press SELECT button to select it.3. Use –,+ to control volume.4. Press MENU button to return previous state. MENU – + ANALOG & DVI◈Special SubmenuSELECT orVOL BUTTON
TFT-LCD Monitor12Resolution Horizontal Frequency(kHz)Vertical Frequency(Hz)Clock Frequency(MHz)Sync Polarity(H/V)VGA (720 x 400) 31.469 70.087 28.322 － / +VGA (640 x 480) 31.469 59.940 25.175 － / －VGA (640 x 480) 37.500 75.000 31.500 － / －SVGA (800 x 600) 37.900 60.320 40.000 + / +SVGA (800 x 600) 46.875 75.000 49.500 + / +XGA (1024 x 768) 48.363 60.004 65.000 + / +XGA (1024 x 768) 60.023 75.029 78.750 + / +SXGA (1280 x 1024) 63.981 60.020 108.000 + / +SXGA (1280 x 1024) 79.976 75.025 135.000 + / +MAC (640 x 480) 35.000 66.667 30.240 － / －MAC (832 x 624) 49.726 74.551 57.284 － / － MAC (1152 x 870) 68.681 75.062 100.000 － / －DPMS with Audio(Option)Mute ON 1W or Below(Analog) / 3.5 W or Below(DVI)Mute OFF 10W or Below Power Management FeatureThe monitor is equipped with a power saving circuit that confirms to the world-standard Display Power Manager Signalling (DPMS) mode of Video Electronics Standard Association(VESA).The power management feature requires that the video card of the computer should support DPMS function. Standard Signal TableStatus LED Sign Power ConsumptionNormal mode Green ON Normal PowerDPMS mode Green Blinking 1 W or Below(Analog)/3.5 W or Below(DVI)No image is displayed with Green blinking.Monitor is in power saving mode.Use mouse or keyboard to release power saving mode.No image is displayed without LED on.Power cable plug must be pulled out.Check the power plug on monitor and on the wall."Out of range" displayed on the screen.This message is displayed when the signal from video card exceeds the maximumfrequency of the monitor. Readjust resolution and frequency in accordance with the monitorcapacity.(Refer to Standard Signal Table)
TFT-LCD Monitor13 Specifications ITEM H750D(B17DF)LCDPanelType Amorphous active matrix super TFT LCDScreen Size 43.2cm (Diagonal)Maximum Resolution 1280 X 1024 @ 75HzPixel Range 0.264mm X 0.264mmDisplay Colors 16.7M ColorContrast Ratio 350 : 1Viewing Angle 70° / 70° / 60° / 60° (Left / Right / Up / Down)Response Time 25 msecLuminance 250 cd/m2Synchronization Horizontal Frequency 79.9 kHz(Max.)Vertical Frequency 75 Hz-Analog / 72Hz-DVI(Max.)Video InputVideo Signal Analog RGB (0.714 Vpp) 75 ohmSynchronous Signal Mode H, V Separate TTL Sync.Power ConsumptionMaximum 48 WPower Saving Mode Under 1 W(Analog)/Under 3.5 W(DVI)Contol Key Front Part SOURCE, MENU/EXIT, AUTO/SELECT, POWER, – / , + / , VOL/MUTEAudio Output Normal 1W / ChMax 1.5W / ChPower Supply Input : 100~240 Vac(50~60Hz), 0.6AWall Mount VESA StandardSafety Standard&EMISafety Standard UL, CE, TUV, CBEMI FCC, RRLLow Radiation MPR - IIDimension Size and Weight 380 X 176 X 368 / 5.8Kg
TFT-LCD 모니터14 Pin assignment table D-Sub Mini 15pin connector Pin No. Assignment Pin No. Assignment1TX2 – 15 Ground2TX2 + 16 5V input3DVI input detect 17 TX0 –4NC 18 TX0 +5NC 19 Ground6 (D_DSCL) 20 NC7(D_DSDA) 21 NC8NC 22 Ground9TX1 – 23 TXC +10 TX1 + 24 TXC –11 Ground 25 NC12 NC 26 NC13 NC 27 NC14 DVI_I ground 28 NCPin No. Assignment Pin No. Assignment1Red Video 95V Input2Green Video 10 Ground3Blue Video 11 Ground4 N.C 12 SDA5Ground 13 H-Sync.6Red Video Ground 14 V-Sync.7Green Video Ground 15 SCL8Blue Video GroundDVI CableAnalog Cable 1 5610 11 15(15 pin D-Sub)1 8 D117 24 D39D2D4
TFT-LCD Monitor15 Troubleshooting Problem SolutionPower LED is dark.No picture.  Check the power connection (Refer to Introduction)OSD, “check signal.” is displayed on the screen.  Check the computer power is on.Message, “check cable.” is displayed on the screen. Check the signal cable between monitor and computer. (Refer to Introduction)Screen looks to be run down.  Perform Auto-config.Screen is not clear. Remove attaches to the signal line(Video extension cable and others) and switch on. Perform Auto-config. Adjust clock and PHASE.Display is unstable and trembling. Check the resolution and frequency of computer and video card, and set up again refer to the current monitor mode and standard signal mode table.Color is irregular.  Adjust COLOR at User Mode in OSD Color Menu.Double images or ‘ghosts’.  Check the resolution and frequency of computer and video card, and set up again in reference to the current monitor mode and standard signal mode table.Picture is dark.  Adjust COLOR at User Mode in OSD Color Menu.Picture is biased or cut or toowide.  Perform Auto-config.Power LED turns into Greenblinking.  Monitor is in DPMS mode.No SOUND.  Check the voice signal connection code or adjust volume.
User’s Guide TFT-LCD MONITOR Visit for more Information www.hansollcd.com
TFT-LCD Monitor2 Table of Contents Introduction - Good Posture Guide Look down the monitor below the horizon. Adjust the monitor to prevent reflection. Relax shoulders and arms, and sit back on the chair. Adjust the monitor stand to acquire required angle. Maintain the arms horizontally and place hands softly on the keyboard. Keep feet flat on the ground.about 50cmIntroduction Good Posture Guide ............................................................................................................................................2 Safety Information ...............................................................................................................................................3 Connection to Signal Source .............................................................................................................................. 5Installing Monitor Driver ............................................................................................................................ 6Service Center ............................................................................................................................................. 10* Place the monitor to face the user and then adjust the monitor angle.* Take a break(for about 10 minutes) at every hour during the work with monitor.* Refer to the following figure to take the correct posture
TFT-LCD Monitor3 Introduction - Safety infomation When connecting/disconnecting the plug, pull out the plug itself, and never pull the cord to prevent fire caused by short. To prevent electric shock, do not connect/disconnect the plug with wet hand. If you see smoke or smell something burning, stop using the unit, switch off the power, pull out the plug, and then contact your local service station. To prevent fire and electric shock, pull out the plug in case of thunder and lightening. To prevent fire, do not connect a large number of equipments in a single line.To prevent damage or loss, please read this warning carefully.
TFT-LCD Monitor4 Install the monitor near an outlet that you can reach easily. Disconnect the product by grasping the plug firmly and pulling in from the outlet. Never disconnect it by pulling the cord. Slots and openings in the cabinet are provided for ventilation; these openings must not be blocked or covered. Never push objects of any kind into cabinet slots or other openings. To prevent fire and electric shock, do not try to take the monitor apart or repair it yourself. Contact your local sevice station or customer sevice center for inspection, modification or repair. Unplug the monitor from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp, lint-free cloth for cleaning. Never insert anything metallic into the monitor openings. Doing so may create a danger of electric shock
TFT-LCD Monitor5 Introduction - Connection to Signal Source<Power Source Connection> <Signal Cable Connection>① ② ③ ① ② ① Port for 12V DC cable from adapter or stand.② Port for signal cable from signal source.③ Port for AC power cable. General For Macintosh Adapter for Macintosh(Optional) Refer to the table on the rear side of the optional Macintosh adapter and adjust DIP switch by the resolution.1. Use 220V or 110 V.(Free Voltage)2. Connect monitor and Signal Source via Signal cable.3. Power on the monitor and computer.4. Connection is finished. Basic Option Basic Option
TFT-LCD Monitor6 Installing Monitor Driver - Automatic Installation - Manual Installation(Windows 2000)1. Insert the CD to the CD-ROM driver.2. Double-click “Install.exe”.3. Select the model and click “OK” button.4. Select inf file, and then click “OK” button.5. Click “Exit” button to close the installation.1. Insert the CD to the CD-ROM driver.2. Click ‘My Computer’ and follow the procedure below.① Click 'Control Panel'. ② Click ‘Display’. ③ Click ‘Settings’.④ Click ‘Advanced..’.⑦ Click ‘Driver’.⑧ Click ‘Update Driver’.⑨ Click ‘Next>’.⑤ Click ‘Monitor’.⑥ Click ‘Properties’.
TFT-LCD Monitor7●Click ‘Finish’.(ex : H711, 730ED...)⑩ Click ‘Display a list of all...’.⑪ Click ‘Next>’.⑫ Click ‘Have Disk...’⑭ Click ‘Next>’. ⑮ Click ‘Next>’⑬ Select the driver and click ‘OK’.3. Select “Exit” if the monitor model is changed, and then reboot the Windows.(ex : H711, 730ED...)(ex : H711, 730ED...) (ex : H711, 730ED...)
TFT-LCD Monitor8(Windows XP) Microsoft ® Windows ® XP Operating System1. Insert CD into the CD-ROM driver. 2. Click "Start" →"Control Panel" then click the "Appearance and Themes" Icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced..".4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button.6. Select "Don't search ,I will.." then click "Next" and then click "Have disk".7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.8. Click the "Close" button then click "OK" button continually.9. Monitor driver installation is completed.(Windows Me) Microsoft ® Windows ® Millennium Operating System1. Click "Start" , "Setting" , "Control Panel". 2. Double click "Display" icon. 3. Select the "Settings" tab and click "Advanced Properties" button. 4. Select the "Monitor" tab. 5. Click the "Change" button in the "Monitor Type" area. 6. Choose "Specify the location of the driver". 7. Choose "Display a list of all the driver in a specific location.." then click "Next" button. 8. Click the "Have Disk" button.9. Specify A:\(D:\driver) then click "OK" button. 10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". 11. Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box. (You can get some other screen for warning message or others, then click the appreciate option for your monitor.)Microsoft ® Windows ® 98 Operating System1. Click "Start" , "Setting" , "Control Panel". 2. Double click "Display" icon. 3. Select the "Settings" tab and click "Advanced Properties" button. 4. Select the "Monitor" tab. 5. Click the "Change" button in the "Monitor Type" area then click "Next" button. 6. Choose "Display a list of all the driver.." then click "Next" button. 7. Click the "Have Disk" button, then click "browse.." button. 8. Specify A:\(D:\driver) then click "OK" button. 9. The "Select Device" dialogue box will appear. Select "Show all devices" then choose the monitor that corresponds to the one you connected to your computer and click OK. 10. Continue choosing "Close" button and "O.K" button until you close the Display Properties dialogue box. (Windows 98)
TFT-LCD Monitor9(Windows 95) Microsoft ® Windows ® 95 Operating System.First determine the Windows 95 version installed on your computer by right-clicking the My Computer icon on PC andselecting Properties. The version number is listed under System. Perform the steps for the appropriate version. Version 4.00.950A 1. Click Start, Settings, Control Panel, and then double-click "Display" icon. 2. In the "Display Properties" window, click the "Settings" tab and click "Change Display Type". 3. In the "Change Display Type" window, click "Change" and then click "Have Disk". 4. Click "browse.." button and specify A:\(D:\driver) and click "OK". 5. In the Select Device window, click the appropriate monitor model and then click OK. 6. Continue choosing "Close" button and "OK" button until you close the "Display Properties" dialogue box. Version 4.00.950B 1. Click Start, Settings, Control Panel, and then double-click "Display" icon. 2. In the "Display Properties" window, click the Settings tab and then click "Advanced Properties" button. 3. In the "Advanced Display Properties" window, click the "Monitor" tab and then click "Change" button. 4. In the "Select Device" window, click "Have Disk" button. 5. Click "browse.." button and specify A:\(D:\driver) and click "OK". 6. In the "Select Device" window, click the appropriate monitor model and then click "OK". 7. Continue choosing "Close" button and "OK" button until you close the "Display Properties" dialogue box. Microsoft ® Windows ® NT Operating System1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Information window, click Settings Tab and then click All Display Modes. 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK. 4. Click Apply button if you see the screen working normally after clicking Test. If the screen is not normal, change to a different mode (lower mode of resolution, colors or frequency). Note: If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Display Modes in the user guide. (Linux) Linux Operating SystemTo execute X-Window, you need to make the X86Config file, which is a type of system setting file. 1. Press Enter at the first and the second screen after executing the X86Config file. 2. The third screen is for setting your mouse. 3. Set a mouse for your computer. 4. The next screen is for selecting a keyboard. 5. Set a Keyboard for your computer. 6. The next screen is for setting your monitor. 7. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.) 8. Set a vertical frequency for your monitor. (You can enter the frequency directly.) 9. Enter the model name of your monitor. This information will not affect the actual execution of X-Window. 10. You have finished setting up your monitor. Execute X-Window after setting other requested hardware. (Windows NT)
10Service Center Country ASC Tel Country ASC TelU. K Pulse Service Centre Ltd. 44-(0)-870-013-4470 Hungary Profit Service Center Kft. 36 1 399 0405Germany BITRONICS GmbH 49-3634-683313 Bulgaria RTS 359-2-971-2020France DATEX 33-1- 69- 310101 SWITZERLANDS TPA PANATLANTIC AG 41 1 886 10 16Spain FREE ELECTRONICA S.A 34 91 6774787 SLOVAKIA BGS-Distribution a.s 421 7 49101563Finland PowerMill OY 358 9 561 86130 LATVIA ELKO-RIGA 371-709-3240Ireland Power Supplies Repair Agency LTD 353 1 286 1343 Greece Alman Hellas Ltd. 3010 2409150Belgium SIMEX NV 32 16 40 58 44 SLOVENIA ACORD 92 d.o.o. 386 1 583 72 62Norway Effekt A/S 47 333 00 630 Croatia ZEL-COS d.o.o 358-1-615-9644Portugal CorpoTecnico 351 21 317 0210 Romania S.C. Shark Industries S.A 40 1 224 22 58Sweden ANOVO Nordic 46 13 202 428 Romania Flamingo Computers SA 4 236 2000(231)Denmark Strax 45 70 10 7101 Yugoslavia PAKOM A.D. 381 18 52 11 16Czech ExtraPoint(Karma) 42022576650 Ukraine MTI 380 44 458 00 32 EUROPECountry ASC TelUSAThink AT(West Area) 1-562-531-3815Far East(East Area) 1-201-935-5939Techpoint(South Area) 1-813-249-5808CANADAKo-Am Electronics(West Area) 1-604-273-5622Electrodesign(East Area) 1-514-331-3202 U.S.A , CANADA

Navigation menu