Hansol LCD B15BF-A LCD Monitor User Manual ENG H530vi

Hansol LCD Inc. LCD Monitor ENG H530vi

User Manual

Parts 3Connection to Computer 4The range of control Angle 5Installing Monitor Driver 6Name and Function of Front 8Power Management Feature 10Adjusting OSD 11Standard Signal Table 17Specification 18Troubleshooting 19Warning 21Table of ContentsINFORMATION TO USER :This equipment has been tested and found to comply with the limits of a ClassB digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmfulinterference in a residential installation.This equipment generates, uses and canradiate radio frequency energy and,if not installed and used in accordance withthe instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particularinstallation; if this equipment does cause harmful interference to radio ortelevision reception, which can be determined by determined by turning theequipment off and on, the user is encouraged to try to correct the interference byone or more of the fllowing measures:1. Reorient/Relocate the receiving antenna.2. Increase the separation between the equipment and receiver.3. Connect the equipment into an outlet on a circuit differencefrom that to which the receiver is connected.4. Consult the dealer or an experienced radio/TV technician for help.Shielded interface cable has to be used to ensure product compliance. CAUTION : Changes or modifications not expressly approved by themanufacturer responsible for compliance could void the user's authority to operate the equipment
32PartsLCD MonitorPlace the monitor to face the user and then adjust the monitor angle.Take a break (for about 10 minutes) at every hour during the work with monitor. Refer to the following figure to take the correct posture. about 50cmLook down the monitorbelow the horizon.Relax shoulders and arms, and sit back on the chair.Adjust the monitor to prevent reflection.Adjust the monitor stand to acquire required angle.Keep feet flat on the ground.Maintain the arms horizontallyand place hands softly on the keyboard.Good Posture Guide12V-DC Adapter (Option)User's Manual /Warranty CardSignal Cable AC Power CableInstallation DisketteFor use only with power supplyMANUFACTURER: AcBelMODEL : API-208-98010MANUFACTURER: MODEL : PSCV45114AMANUFACTURER: MODEL : U048-S012035HAMANUFACTURER: MODEL : LS-42S
Option Basic 54Connection to Signal Source 1. Use 220 V or 110 V. (Free Voltage)2. Connect monitor and Signal Source via Signal cable3. Power on the monitor and computer.4. Connection is finished.Basic General For MacintoshAdapter for Macintosh (Optional)Refer to the table on the rear side ofthe optional Macintosh adapter andadjust DIP switch by the resolution. T he range of control AnglePower Adapter FormPower Stand FormOption Forward 4 Default Backward 31Forward 4 Default Backward 31Port For12V DC Cable Fromadapter or Stand.Port For Signal Cable From Signal Source.Port For AC Power Cable< Power source connection > < SIgnal cable connection>
76Click 'Finish'.Click 'Next>'.Click 'Advanced..'. Click 'Next>'.Click 'Monitor'. Click 'Change..'.Click 'Display a list of all...'.Click 'Next>'.Click 'Have Disk..'.Select the driver and click 'OK'. Click 'Next>'.3. Select "Exit" if the monitor model is changed, and then reboot the Windows.Installing Monitor Driver1. Insert the Diskette to the Floppy Diskette driver. 2. Double-click "Install.exe". 3. Select the model and click "OK" button.4. Select inf file, and then click "OK" button.5. Click "Exit" button to close the installation.Automatic InstallationManual Installation1. Insert the Diskette to the Floppy Diskette driver.2. Click 'My Computer' and follow the procedure below.Click 'Control Panel'. Click 'Display'. Click 'Settings'.Run (Click) "Install" at Floppy driver and select the model name to set theoptimum display in Window 95, 98 or 2000.Use the Driver provided.
98, +/-/Power buttonPower button is located in the lower center of the Front Bezel.You can push the button to turn on/off the power.Power Indicating LEDIf the green LED around the power switch turns into blinking, it indicates the monitor is in power saving mode.On Screen Display (OSD) Function ButtonOSD buttons on the front of bezel perform the following functions.MENU : Press the button to display menus. If you press this button when OSD is displayed, you can switch display to the previous menu and exit menu. SELECT/ AUTO : Press this button, when OSD is displayed, to select the menu.. When OSD is not displayed, you can perform automatic setting.. POWER : Power button.: By pressing these button when OSD is displayed, you can move cursor into the menus which you want.After the SELECT button, you can change gauge level or select sub menus.When OSD is not displayed, you can adjust brightness and contrast. FunctionsName and Function of Front Front panelSELECT/AUTO BUTTONMENU BUTTONPOWER BUTTON+/ BUTTON- / BUTTON
1110Horizontal PositionAdjusting OSDBrightnessContrastMENU1. Press the Menu button.2. Use to move Brightness ICON.3. Use SELECT button to select it.4. Use to adjust the brightness. 5. Press SELECT button to exit.6. Press MENU button to finish adjusting OSD. SELECTMENU SELECTMENU SELECT1. Press the Menu button.2. Use to move Contrast ICON.3. Use SELECT button to select it.4. Use to adjust the contrast.5. Press SELECT button to exit.6. Press MENU button to finish adjusting OSD. 1. Press the Menu button.2. Use to move H-Position ICON.3. Use SELECT button to select it.4. Use to adjust display left or right.5. Press SELECT button to exit.6. Press MENU button to finish adjusting OSD. No image is displayed with Green blinking.Monitor is in power saving mode.Use mouse or keyboard to release power saving mode.No image is displayed without LED on.Power cable plug must be pulled out.Check the power plug on monitor and on the wall."Out of range" displayed on the screen.This message is displayed when the signal from video card exceeds themaximum frequency of the monitor. Readjust resolution and frequency inaccordance with the monitor capacity. (Refer to Standard Signal Table)Power Management FeatureWhen not in use for a long time, the monitor automatically reduces its power consumption, meeting power savingstandards of EPA and NUTEK. The monitor is equipped with a power saving circuit that confirms to the world-standard Display Power Manager Signalling(DPMS) mode of Video Electronics Standard Association (VESA).The power management feature requires that the video card of thecomputer should support DPMS function. Status LED Sign Power ConsumptionNormal Green ON Normal PowerDPMS mode Green Blinking( 2 second interval ) 5 W or Below
1312Clock PhaseUser Color1. Press the Menu button.2. Use to move Color ICON.3. Use SELECT button to select it.4. Press MENU button to return previous menu.1. Use to move Red, Green, Blue ICON.2. Use SELECT button to select color what you want.3. Use to increase or decrease each color.4. Press SELECT button to exit.5. Press MENU button to return previous menu. 1. Press to move I or II.2. Press SELECT button to select.3. Press SELECT to exit. 4. Press MENU button to return previous menu. I:Bluish white II : Reddish whiteMENUMENU SELECTMENUSELECTColorPreset ColorClock Phase1. Press the Menu button.2. Use to move V-Position ICON.3. Use SELECT button to select it.4. Use to adjust display upward or downward.5. Press SELECT button to exit.6. Press MENU button to finish adjusting OSD. 1. Press the Menu button.2. Use to move Clock Phase ICON.3. Use SELECT button to select it.4. Use to correct fine trembling or Video noise.5. Press SELECT button to exit.6. Press MENU button to finish adjusting OSD. 1. Press the Menu button.2. Use to move Clock ICON.3. Use SELECT button to select it.4. If Auto-cnfig function fails to remove Video noise, Use orto remove vertical noise.( Adjusting clock phase is required after the adjustment of clock.) 5. Press SELECT button to exit.6. Press MENU button to finish adjusting OSD. MENU SELECTMENU SELECTMENU SELECTVertical PositionClockClock Phase
15141. Use to move OSD Overlay ICON.2. Use SELECT button to select it.3. Press to select what you want.4. Press SELECT button to exit.5. Press MENU button to return previous menu. 1. Use to move Sharpness ICON.2. Use SELECT button to select it.3. Press to select what you want.4. Press SELECT button to exit.5. Press MENU button to return previous menu.1. Press the Menu button.2. Use to move Language ICON.3. Use SELECT button to select it.4. Use to select language in order.5. Press SELECT button to exit.6. Press MENU button to finish adjusting OSD.MENU SELECTMENUSELECTMENUSELECTLanguageSharpnessSharpnessOSD OverlayOSD Overlay1. Press the Menu button.2. Use to move SPECIAL ICON.3. Use SELECT button to select it.4. Press MENU button to return previous menu.1. Use to move Video Level ICON.2. Use SELECT button to select it.3. Use to select level.4. Press SELECT button to exit.5. Press MENU button to return previous menu.1. Use to move OSD Timing ICON.2. Use SELECT button to select it.3. Press to adjust OSD Timing 4. Press SELECT button to exit.5. Press MENU button to return previous menu. MENU SELECTMENUSELECTMENUSELECTOSD Timing SharpnessVideo LevelOSD OverlaySpecial
1716Standard Signal TablePin assignment table D-SubMini 15pin connectorVGA (720 X 400)VGA (640 X 480)VGA (640 X 480)SVGA (800 X 600)XGA (1024 X 768)XGA (1024 X 768)MAC (640 X 480)MAC (832 X 624)31.46931.46937.50046.87548.36360.02335.00049.72670.08759.94075.00075.00060.00475.02966.66774.55128.32225.17531.50049.50065.00078.75030.24057.284ResolutionHorizontal Frequency (KHz)Vertical Frequency(Hz) Clock Frequency(MHz)1511 1561015pin D-SubPin No. Assignment Pin No. Assignment 1 Red Video 9 5V Input 2 Green Video 10 Ground3 Blue Video 11 Ground4 N.C 12 SDA5 Ground 13 H.Sync6 Red Video Ground 14 V.Sync7 Green Video Ground 15 SCL 8 Blue Video Ground1. Press the Menu button.2. Use to move the Auto-config ICON.3. Press SELECT button to see S/W revision date. 4. Press SELECT button to exit.5. Press MENU button to finish adjusting OSD. You can know a display information(Horizontal, Vertical Frequency) 1. Press the Menu button.2. Use to move the Auto-config ICON.3. Press SELECT button to select it.( After auto configuration OSD disappear.) In most case, Auto-Config adjusts displayappropriately. Use PH or adjust CLKin accordance with graphic card to fine tunethe display.MENU SELECTMENUMENU SELECT1. Press the Menu button.2. Use to move the Reset ICON.3. Press SELECT button to select it.4. Press MENU button to finish adjusting OSD. (By selecting Reset ICON, you can initialize OSD menu.) Auto-ConfigAuto-ConfigAuto-ConfigInformationAuto-ConfigMenu Reset
1918TroubleshootingCheck the power connection. (Refer to page 4)Power LED is off.No picture.Check the signal cable between monitor and computer. (Refer to page 4)Perform Auto_config.Check the computer power is on.Message, "No signal."is displayed on thescreen.Screen looks to be rundown.Screen is not clear.Check the resolution and frequency of computer and video card, and set up again refer to the current monitor mode and standard signal mode table.Display is unstable andtrembling.Remove attaches to the signal line(Video extension cable and others) and switch on.Perform Clock and Adjust PHASE.Switch off/on the monitor.Check the computer connection cable. (Refer to page 4)Message, "No cable"is displayed on thescreen.SpecificationType Amorphous active matrix super TFT LCDScreen Size 38.1cm (Diagonal)Maximum Resolution1024 X 768 @ 75 HzPixel Range0.297 mm X 0.297 mmDisplay Colors 262,144 ColorContrast Rate 300 : 1Visual Angle 70° / 70° / 55° / 60° (Left / Right / Up / Down)Response Speed 25 msBrightness 250 cd/m2Horizontal Frequency 60kHz (Max.)Vertical Frequency 75 Hz (Max.)Video Signal Analog RGB (0.714 Vpp) 75 ohmSynchronous Signal Mode H, V Separate TTL Sync, Maximum 32WPower Saving Mode Under 5 WMENU, SELECT/AUTO, POWER,Input: 90/264V (50~60 Hz)Output: 12V, 3.35 A, 40WInput: 90/264V (50~60 Hz)Output: 12V, 3.5A, 42WVESA StandardSafety Standard UL, CE, TUV, CBEMI FCCLow Radiation MPR-IIPower Stand 358 X 214 X 353.5 / 3.98 KgPower Adapter 358 X 128 X 346 / 3.8 KgLCDPanelSynchronizationModel H530(B15BF) VideoInputPower ConsumptionControl keyFront Part SafetyStandard& EMIDimensionPower Stand Power Adapter (option) Wall Mount, +/-/Size and Weight
2120WarningTo prevent damage or loss, please read this warning carefully.When connecting/disconnecting the plug, pull out the plug itself, and never pull the cord to prevent fire caused by short.To prevent electric shock, do not connect/dis-connect the plug with wet hand.To prevent fire, do not connect a large number ofequipments in a single line.To prevent fire and electric shock, pull out the plug incase of thunder and lightening.To prevent fire and electric shock, do not try to takethe monitor apart or repair it yourself. Contact yourlocal service station or customer service center forinspection, modification or repair.If you see smoke or smell something burning, stopusing the unit, switch off the power, pull out the plug,and then contact your local service station.Check the resolution and frequency of computer and video card, and set up again in reference to the current monitor mode and standard signal mode table.Double images or'ghosts'.Perform Auto-Config.Adjust COLOR at User Mode in OSD Color Menu.Picture is dark.Picture is biased or cutor too wide.Monitor is in power saving mode.Power LED turns intoblinking.Adjust COLOR at User Mode in OSD Color Menu.Color is irregular.
22Memo

Navigation menu