Handheld Group 14249-RF2 Handheld Device User Manual 1

Handheld Group AB Handheld Device Users Manual 1

Users Manual-1

NAUTIZ X9 MANUAL
Ver 1.0 2COPYRIGHT Copyright © 2018 Handheld Group AB. All Rights Reserved. This document contains proprietary information protected by copyright. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer. DISCLAIMER The information in this document is subject to change without prior notice in order to improve the reliability, design and function. It does not represent a commitment on the part of the manufacturer. Under no circumstances will the manufacturer be liable for any direct, indirect, special, incidental, or consequential damages arising from the use or inability to use the product or documentation, even if advised of the possibility of such damages. ABOUT THIS MANUAL This user’s manual provides the general information and installation instructions for the product. The manual is meant for the experienced users and integrators with hardware knowledge of personal computers. If you are not sure about any description in this manual, consult your vendor before further handling. We recommend that you keep one copy of this manual for the quick reference for any necessary maintenance in the future. Thank you for choosing a Handheld product.
Ver 1.0 3DECLARATION OF CONFORMITY CE The CE symbol on your product indicates that it is in compliance with the directives of the Union European (EU). A Certificate of Compliance is available by contacting Technical Support. This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. FCC RF Exposure Information (SAR) This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are conducted using standard operating positions accepted by the FCC with the EUT transmitting at the specified power level in different channels. The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/eot/ea/fccid . To ensure that RF exposure levels remain at or below the tested levels, use a belt clip, holster, or similar accessory that have no metallic component in the assembly and must maintains a minimum separation distance of 10mm between your body and the device. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation.
Ver 1.0 4RoHS Handheld Group AB certifies that all components in its products are in compliance and conform to the European Union’s Restriction of Use of Hazardous Substances in Electrical and Electronic Equipment (RoHS) Directive 2002/95/EC. The above mentioned directive was published on 2/13/2003. The main purpose of the directive is to prohibit the use of lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB), and polybrominated diphenyl ethers (PBDE) in electrical and electronic products. Member states of the EU are to enforce by 7/1/2006. Handheld Group AB hereby states that the listed products do not contain unintentional additions of lead, mercury, hex chrome, PBB or PBDB that exceed a maximum concentration value of 0.1% by weight or for cadmium exceed 0.01% by weight, per homogenous material. Homogenous material is defined as a substance or mixture of substances with uniform composition (such as solders, resins, plating, etc.). Lead-free solder is used for all terminations (Sn(96-96.5%), Ag(3.0-3.5%) and Cu(0.5%)). SVHC / REACH To minimize the environmental impact and take more responsibility of the earth where we live, Handheld hereby confirms all products comply with the restriction of SVHC (Substances of Very High Concern) in (EC) 1907/2006 (REACH--Registration, Evaluation, Authorization, and Restriction of Chemicals) regulated by the European Union. All substances listed in SVHC < 0.1 % by weight (1000 ppm)
Ver 1.0 5 Symbols Description This symbol of “CAUTION” indicates that there is a danger of injury to the user or a risk of damage to the product, should warning notices be disregarded. Important Safety Instructions Read these safety instructions carefully: 1. Read all cautions and warnings on the equipment. 2. Place this equipment on a reliable surface when installing. Dropping it or letting it fall may cause damage 3. Make sure the correct voltage is connected to the equipment. 4. For pluggable equipment, the socket outlet should be near the equipment and should be easily accessible. 5. Keep this equipment away from humidity. 6. Disconnect this equipment from the A/C outlet before cleaning it. Use a moist cloth. Do not use liquid or sprayed detergent for cleaning. 7. To fully disengage the power to the unit, please disconnect the power from the AC outlet. 8. Do not scratch or rub the screen with a hard object. 9. Never use any of the solvents, such as Thinner Spray-type cleaner, Wax, Benzene, Abrasive cleaner, Acid or Alkaline solvent, on the display. Harsh chemicals may cause damage to the cabinet and the touch sensor. 10. Remove dirt with a lightly moistened cloth and a mild solvent detergent. 1. Then wipe the cabinet with a soft dry cloth. 11. The openings on the enclosure are for air convection and protect the equipment from overheating. DO NOT COVER THE OPENINGS 12. Position the power cord so that people cannot step on it. Do not place anything over the power cord. 13. If the equipment will not be used for a long time, disconnect it from the power source to avoid damage by transient overvoltage. 14. Never pour any liquid into openings. This may cause fire or electrical shock. 15. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.
Ver 1.0 616. If one of the following situations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped or damaged. f. The equipment has obvious signs of breakage. 17. The sound pressure level at the operator’s position, according to IEC 704-:1982, is no more than 70dB(A). 18. Keep this User’s Manual for later reference. 19. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). THIS MAY DAMAGE THE EQUIPMENT. Do not use the power adapter that isn’t made for the equipment. Supplying the equipment with inappropriate voltage may cause harm to the battery or, even worse, burn the equipment. To prevent possible hearing damage, do not listen at high volume levels for long periods
Ver 1.0 7Rechargeable Battery Pack Safety With very little care, you can optimize the battery life and maximize the lifespan of the battery. Most importantly, use only the equipment in its ideal operating temperature – do not leave it in a hot trunk during the summer. Important Terms to Understand “Battery life” means the time the equipment will run before it must be recharged (sometimes this is also called “playtime” or “runtime”). “Battery lifespan” means the total amount of time your battery will last before it must be replaced. Using the Equipment for the First Time Be sure to fully charge the equipment when charging the equipment for the first time. Long-Term Storage & Maintenance If you are putting away the battery for more than three months, it is recommended that the battery should be stored separately and fully charged, and get recharged every three months. If you store an uncharged battery, it could fall into a deep worn-out state which would render it incapable of holding any charge. Be sure to store the equipment and battery at the proper temperature (as described in 1.5 Specifications). Battery Lifespan The removable batteries for the equipment are designed to retain up to 80% of their original capacity after 300 charging and recharging cycles when properly maintained. You may choose to purchase new battery when it no longer holds the sufficient charge that meets your needs. • The lithium-ion battery is currently one of the most popular battery packs. • The best advantage is that it has no memory effect, so users needn’t worry about that issue. Users can charge the battery anytime whether it is fully drained or not. However, it’s recommended that users drain the battery until the system shows power shortage warning and then recharge the battery. Doing so is helpful to the reliability of your battery. • Don’t use the battery pack as a power supply for other equipment. • Don’t expose the battery to elevated heat situations such as under direct sunlight in a car or near fire. • Don’t disassemble the battery, or the battery leakage might cause skin or eye injury. If electrolyte leaking from the battery contacts your skin or clothing, immediately flush it with running water. If it splashes into eye, rinse the eye at least 15 minutes with clean water and then seek medical attention. • To avoid battery leakage or explosion, don’t discard the battery into water or fire, or put them near a heat source such as a gas stove or an oven. • If you are putting away the battery for more than three months, it is recommended that the battery should be stored separately and fully charged, and get recharged every three months. If you store an uncharged battery, it could fall into a deep worn-out state which would render it incapable of holding any charge. Be sure to store the equipment and battery at the proper temperature (as described in 1.5 Specifications). • Use the appropriate container to store the battery such as a paper box. Do not allow a metal object to touch the terminal of the battery. • The battery consists of precise electrical components and cells. Do not drop or hit the battery.
Ver 1.0 8Disposing of the Equipment Within the European Union EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic products carrying the mark (left) must be disposed of separately from normal household waste. This includes monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your display products, please follow the guidance of your local authority, or ask the shop where you purchased the product, or if applicable, follow any agreements made between yourself. The mark on electrical and electronic products only applies to the current European Union Member States. Outside the European Union If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority so as to comply with the correct disposal method. Additional Information & Technical Support You can download the related technical documents such as datasheet and user’s manual as well as driver on our website. Please do not hesitate to call or e-mail our customer service when you still cannot get the information you need. https://www.handheldgroup.com/support-rugged-computers/knowledgebase/ E-mail: support@handheldgroup.com
Ver 1.0 9Warranty This product is warranted to be in good working order during the warranty period. Should this product fail to be in good working order at any time during this period, we will, at our option, replace or repair it at no additional charge except as set forth in the following terms. This warranty does not apply to products damaged by misuse, modifications, accident or disaster. Vendor assumes no liability for any damages, lost profits, lost savings or any other incidental or consequential damage resulting from the use, misuse of, or inability to use this product. Vendor will not be liable for any claim made by any other related party. Vendors disclaim all other warranties, either expressed or implied, including but not limited to implied warranties of merchantability and fitness for a particular purpose, with respect to the hardware, the accompanying product’s manual(s) and written materials, and any accompanying hardware. This limited warranty gives you specific legal rights. Return authorization must be obtained from the vendor before returned merchandise will be accepted. Authorization can be obtained by calling or faxing the vendor and requesting a Return Merchandise Authorization (RMA) number. Returned goods should always be accompanied by a clear problem description.
Ver 1.0 101. INTRODUCTION 1.1. Product Highlights • Support Android 7.0 • Quad-core ARM Cortex-A53 1.3GHz • Multiple connectivity including WLAN, WWAN, Bluetooth, NFC and 2G/3G/LTE • Worldwide modem capability (Support FDD/TDD-LTE, WCDMA, CDMA2000 1xEV-DO GSM/GPRS/EDGE) • IP67 rated water and dust resistance • Drop proof: Up to 1.5m • Accelerometer, Magnetometer, Gyroscope, Light sensor, GPS & Barometer • Built-in 1D/2D barcode reader 1.2 Package Contents Upon opening the package, carefully inspect the contents. If any of the items is missing or appears damaged, contact your local dealer or distributor. The package should contain the following items: Nautiz X9 Main Body Standard Battery Power Adapter Quick Start Guide
Ver 1.0 111.3 Parts of the Device NOTE Do not remove transparent film unless you are using the pistol grip accessory
Ver 1.0 121.4 Dimensions
Ver 1.0 131.5 Specifications System CPU Quad Core ARM Cortex-A53 1.3GHz OS Android 7.0 Memory 2GB LPDDR2 Storage 16 GB eMMC Peripherals and Devices Camera Front: 2.0 MP camera Rear: 13.0 MP camera with Auto-Focus and Flashlight Sensor Magnetometer (M-Sensor/E-Compass) Accelerometer (G-sensor) Gyroscope Barometer Proximity sensor Ambient light sensor Magnetometer (M-Sensor/E-Compass) Accelerometer (G-sensor) Gyroscope Barometer Proximity sensor Ambient light sensor Barcode Scanner 2D barcode reader with physical trigger button Audio & Vibrator 1 x built-in microphone 1 x built-in speaker (1W) 1 x 3.5mm stereo headphone/microphone combo jack 1 x vibrator FM radio Wireless WLAN Integrated IEEE 802.11a/b/g/n Bluetooth Bluetooth 4.1 (BLE, HS compliant) WWAN (Global) WWAN (NA) 2G GSM/GPRS/EDGE (900/1800) 3G WCDMA (B5, B8) 4G (B1, B3, B8, B20, B38, B39, B40) 2G GSM/GPRS/EDGE (900/1800) 3G WCDMA (B2, B5) 3G CDMA2000 (BC0/BC1) LTE (B2, B4, B12, B13, B17)
Ver 1.0 14GPS GPS/GLONASS NFC Yes I/O Interface USB Port 1 x micro USB 2.0 port High Speed / OTG Compatible SD Slot 1 x microSD card slot SIM Cart 1 x micro-SIM (3FF) socket supporting 2G/3G/LTE 1 x micro-SIM (3FF) socket supporting 2G only LCD Display Size/Type 5“ TFT LCD Resolution 720(W) x 1280(H) Brightness (cd/m²) 400 cd/m² Touch Screen 5 points capacitive touch (PCT) Power Supply Battery Type Lithium-ion rechargeable battery, field replaceable Battery Capacity Typical 3.7V, 4800mAh Battery Life TBD Adapter Input AC100~240C, 50~60 Hz Adapter Output 5V/2A (10W) Mechanical & Environmental Ingress Protection IP67, Up to 1.5m drop resistance. Operating Temp. -20°C ~ 55°C (-4°F ~ 131°F ) Storage Temp. -20°C ~ 60°C (-4°F ~ 140°F) Operating Humidity 5~95% RH Dimensions (mm) 165.8(H) x 86(W) x 25.6(D) Weight under 385g (0.85lb) (with battery)
Ver 1.0 152. GETTING STARTED 2.1 Installing microSD and SIM Card To install the microSD card and/or SIM card(s): 1. Pull the back cover release latch towards the bottom of the phone to unlock the latch. Latch locked Latch unlocked 2. Insert a small flathead screwdriver into the notch and gently pry up the cover. 3. Remove the battery, if inserted. The battery is secured by a red slider. Move the slider to the right so that you can remove the battery. Move the slider to the right to unlock the battery.
Ver 1.0 16 4. Insert the SIM cards / microSD card following the direction as shown in the graphic.  To insert SIM card(s): The device comes with two SIM card slots, each with their own supported networks. SIM card slot 1 supports 2G, 3G and 4G while slot 2 supports 2G network. Make sure to insert your SIM cards correctly. SIM slot 2: 2G SIM slot 1: 2G/3G/4G  To insert a microSD card: Push the microSD card cover toward SIM slot 1 to lift it up. Insert a microSD card following the direction as shown in the graphic. Then push the microSD card cover back into its original position to lock it. 5. Insert the battery back to the compartment while ensuring gold contacts align with the device contacts. Then move the slider to the left to secure the battery. Move the slider to the left to secure the battery.
Ver 1.0 176. Replace the back cover and push the latch towards the cover to lock it. After the SIM card(s) are properly installed, the device is ready to use the cellular network. See 3.3 Using Cellular Network to know how to use them. 2.2 Charging the Battery You can charge the Nautiz X9 via the provided power adapter or computer USB connection.  Due to shipment, the battery is partially drained when the package is delivered to you. Be sure to charge the battery to full when you are charging it for the first time.  To use the power adapter: Connect the power adapter to your power outlet and connect the USB end to the USB port on the device.  To use a computer USB connection: Using a USB cable, connect small end to the USB port on the device and the other end to the USB port on a computer. WARNING: Use only the power adapter that comes with your device. Using a different power adapter may damage your device and may result in poor performance. It may also invalidate warranty applying to the device. 2.2.1 Checking the Battery Level When you charge the Nautiz X9, the LED indicator will show the charging status as below:  Charging in progress: Red, solid  Fully charged: Green, solid

Navigation menu