Hafele America 104 Wall-mounted door and lock control User Manual PW3104

Hafele America Co. Wall-mounted door and lock control PW3104

PW3104 User Manual

Wall TerminalMounting instructions
Mounting instructionsengl. 15Technical informationAll wall terminals are supplied in the basic method of operation.With this method of operation, electronic keys are given accessauthorisations directly at the wall terminal with a special programmingkey stick (green). Up to 100 electronic keys can be allocated per wallterminal. With a clearing key stick (red), the access authorisations of anauthorised electronic key can be withdrawn directly at the wall terminal.If a different method of operation needs to be chosen, please contactyour Dialock sales office.Technical dataVoltage supply 10 - 12 VDC, 8 - 10 VACContinuous current intake <200 mAPeak current intake 250 - 400 mA, depending onnumber of relaysNumber of relays 1 - 3Contact load relayVoltage on contact max. 60 VDC, max. 125 VACCurrent on contact max. 2 A, (short term)Contact rating max. 30 W, max. 60 VAContinuous current max. 1 AData retention in case of power cut 10 yearsfor externalsector for internalsectorProtection levelReader module IP 68 IP 54Control electronics module IP 66 IP 66Temperature-operating rangeReader module -20 - 80 °C 0 - 60 °CControl electronics module 0 - 60 °C 0 - 60 °Crelative air humidity (noncondensating)0 - 95 % 0 - 95 %
Mounting instructions16 engl.Range of applicationWall terminals control electric door openers and motor locks for:external or internal doorsor:automatic roller shuttersbarriersappliances and installations, such as goods dispensers or sun bedscan also be monitored via wall terminals.Important characteristics:suitable for surface- and flush fitted installationcan be used as cash terminalcan be connected to a central unit (PC) via online adapterSupply scheduleThe configuration supplied, consists of:reader module with approx. 2.5m long, round, flat band cable andplug for connection to the control electronics modulefront foil to apply onto the reader modulespacer plate for the surface installation of the reader modulecontrol electronics module with one relay (optionally up to 3)screw fixings for the casing of the control electronics modulePG-9-screw fixing for connecting the flat band cable to the controlelectronics modulefeeder implement to connect cables to the control electronics modulespare plug for the flat band cable
Mounting instructionsengl. 17InstallationThe following steps are necessary for the installation:install the reader moduleinstall the control electronics moduleelectrical installation6 5 4310789121 flat band cable (round, shielded)2 reader module3 element to be switched (appliance)4 power supply for element to be switched (appliance)5 distributor6 control electronics module7 power supply for control electronics module8 conductor9 interface cable (optional)10 online-adapter (optional)During the planning phase, the following installation measures need tobe considered:internal or external installation of the modulesexact location for the modules to be installed, considering theposition of the elements to be switched (i.e. door lock, barrier)surface- or flush fitted installation of the modulesconnection of the wall terminals to a central unit (PC) via online-adapter
Mounting instructions18 engl.Install the reader modulePreparations:drill a hole into the wall for the connecting cable between the readermodule and the control electronics module. Lay a protective pipewith an internal diameter of at least 12 mm or a cable channel.flush fitted installation: install a flush fitted container with a diameter of70 mm and a minimum depth of 60 mm.surface installation: drill a 25 mm diameter hole and minimum 48 mmdepth for the PG-9-screw fixing.123min. 4845min. 25123min. 60470Flush fitted installation (left) and surface installation (right) of the reader module1 protective pipe (internal diameter min. 12 mm)2 cable (diameter = 8 to 9 mm, length = 2,5 m)3 flush fitted container, resp. drilling for PG-9-screw fixing4 reader module5 spacer plate1. for flush fitted installation: drill a 12 mm diameter hole in the centreof the flush fitted container.2. for flush fitted installation: remove the spacer plate of the readermodule.
Mounting instructionsengl. 191 spacer plate2 reader module3 10-mm-hole4 front foil3. For installation on brick work:Ødrill holes for 6 mm dowels into the wall to fix the reader module.Øfix the reader module with 4 Hospa screws, 4x50 mm. Makesure, that the 10 mm hole is at the bottom and that the screwsdo not protrude over the countersinkings.4. For installation on metal:Ødrill four holes for an M4 thread.Øcut the threadØfix the reader module with four countersunk screws. Make sure,that the 10 mm hole is at the bottom and that the screws do notprotrude over the countersinkings.5. guide the free end of the cable through the hole in the brick work tothe control electronics module.If the plug does not fit through the hole in the brick work:Øcut off the plug.Øloosen the PG-9-screw fixing and strip it off the cable.
Mounting instructions20 engl.Øguide the free end of the cable through the hole to the controlelectronics module.Øcut the cable to length.Øre-fit the PG-9-screw fixing to the cable.Øguide the flat band cable through the aperture in the spare plug,such that the arrow on the plug is on the same side as the redmarking of the flat band cable (polarity!)Øsqueeze the spare plug shut with water pump pliers or withspecial squeezing pliers.6. Apply the front foil onto the reader module. Line up the cut outs ofthe front foil with the apertures in the reader module for coverage.
Mounting instructionsengl. 21Install the control electronics moduleConditions:cables and power supply for all appliances to be connected havebeen laidfor flush fitted installation: a sufficiently large drilling has beenprepared123434251Flush fitted installation (left) and surface installation (right) of the controlelectronics module1 protective pipe (internal diameter min. 12 mm)2 cable (diameter = 8 to 9 mm, length = 2,5 m)3 control electronics module4 connection for power supply5 inspection flapØDrill four holes for 6 mm dowels into the wall to fix the controlelectronics module.
Mounting instructions22 engl.Electrical installation24+RxDataTxDataGNDRTSCTSNONCCOMNONOCOMCOM78Input1Input2S-Input1635NCNC1Occupancy schedule of the control electronics module1 Plate of control electronics module2 TTL-entrances, to be approached via a switch3 relay 3 (optional)4 relay 2 (optional)5 relay 16 flat band cable connection to the reader module (pin bar)7 supply voltage8 serial RS-232-interface to the PC or online adapter
Mounting instructionsengl. 234 321654 3215Switch example: joint (top) and separate (bottom) power supply for theconsuming device and the terminal1 transformer (adapted to the voltage and output requirements of theelement to be switched)2 element to be switched (appliance)3 relay 14 connection for the reader module5 plate of control electronics module6 transformer (adapted to the voltage and output requirements of theelement to be switched)
Mounting instructions24 engl.Danger of death through an electric shock!ØMake sure, that the electrical installation is carried out by qualifiedpersonnel.Destruction of the relay contacts when operating the dooropener with direct current!ØUse a free running diode.1. turn off the fuses of all consuming devices to be connected and thepower supply for the wall terminal!2. make sure, all cables are voltage-free.3. drill holes to feed the cables of the PG-9-screw fixings for thereader module, power supply, elements to be switched and ifnecessary the cable of the online adapter into the casing of thecontrol electronics module.4. cut the cable to length.5. slide the PG-9-screw fixings onto the cable to be connected.6. fix the casing of the control electronics module to the wall with fourHospa-screws 4 x 50 mm.7. guide the cables through the holes in the casing.8. slide the nuts of the PG-9-screw fixings onto the cables and tightenthe PG-9-screw fixings.
Mounting instructionsengl. 25The plate is destroyed, if inappropriate tools are used!ØConnect the cables of the appliances to be connected only with theenclosed feeder implement.121 feeder implement2 contact clamp9. open the contact clamps with the feeder implement.10. slide the cable into the contact apertures.11. remove the feeder implement.12. insert the cable of the sensor head into the pin bar.13. fix the casing lid onto the casing with the enclosed plastic screws.14. if the control electronics module is flush-fitted: install an inspectionflap.
Mounting instructions26 engl.Initiation for basic method of operationAllocate the programming and deletion key-stickIn the basic method of operation, the programming and deletion key-sticks are allocated during the initiation.This step is only possible straight after the installation of the supplyvoltage for the wall-terminal.Prevent the misuse by unauthorised persons!ØKeep the programming and deletion key-sticks in a safe place, asthese can allocate and withdraw locking authorisations to/ from anelectronic key.1. Have the green programming key-stick and the red deletion key-stick ready.2. If there is voltage already at the wall terminal, interrupt the voltage.3. Produce voltage supply.The green indicator (LED) flashes for a few seconds.4. Place the green programming key-stick in front of the readermodule, whilst the green LED flashes.The red indicator (LED) flashes briefly to confirm the successfulallocation.5. Place the red deletion key-stick in front of the reader module, whilstthe red LED flashes.The red indicator (LED) is illuminated.If errors have occurred during the allocation:Ødisconnect and re-connect the voltage.ØRe-allocate the programming and deletion key-stick.If continuous errors occur:Øcontact your Dialock-sales office.
Mounting instructionsengl. 27Brief operating instructions for basic method of operationAllocate access authorisations1. Place the green programming key-stick in front of the readermodule.The green indicator (LED) flashes.2. Place the key to be introduced in front of the reader module within5 seconds.The green indicator (LED) flashes briefly.The locking authorisation for the electronic key to be introduced hasbeen allocated.3. Remove the introduced key.If the red indicator (LED) is illuminated, the attempt has beenunsuccessful:Ørepeat the allocation of the access authorisations.4. Place the next electronic key to be introduced in front of the readermodule in intervals of 5 seconds.Withdraw access authorisations1. Place the red deletion key-stick in front of the reader module.The red indicator (LED) flashes.2. Place the electronic key to be deleted in front of the reader module.The red indicator (LED) flashes briefly.The access authorisations are withdrawn.Withdraw the access authorisations of all electronic keysIf an electronic key has been lost and should no longer have lockingauthorisations, all electronic keys have to be deleted at the readermodule. Afterwards, all electronic keys which should have accessauthorisations, have to be re-allocated.1. Place the red deletion key-stick in front of the reader module.The red indicator (LED) flashes.2. Place the green programming key-stick in front of the readermodule.The red indicator (LED) flashes briefly.3. All electronic keys, which need to retain the locking authorisation,will be re-allocated with access authorisations.
Mounting instructions28 engl.How to operate the Wall TerminalØPlace the electronic key with locking authorisation in front of thereader module at a distance of a few centimetres.The green indicator (LED) lights up, the red indicator (LED) switchesoff.The element to be switched is activated, i. e. the door opener isunlocked.If the LEDs do not switch from red to green:ØPlace the electronic key closer to the terminal.If the LEDs still do not switch from red to green:The electronic key has no access authorisation.ØPlace the access authorised electronic key in front of the readermodule.
Mounting instructions 732.29.101The reprint of the mounting instructions, even extracts, or copying of the illustrations and drawings as wellas copying of the layout are prohibited.No liability is accepted for printing errors or errors occurred during the creation of the mounting instructions.We reserve the right for technical changes and changes of availability.Status 06.00CopyrightHäfele GmbH & CoAdolf-Häfele-Strasse 1 · D-72202 NagoldPostfach 1237 · D-72192 NagoldTelefon +49 (0) 74 52 / 95-0Telefax +49 (0) 74 52 / 95-200E-Mail: info@haefele.de · www.haefele.deNOTICE: Any changes or modifications made to the Wall Terminal will voidthe user's authority to operate this equipment in compliance with FCCregulations.NOTE: This equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to Part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses andcan radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures: Reorient or relocatethe receiving antenna. Increase the separation between the equipment andreceiver. Connect the equipment into an outlet on a circuit different from thatto which the receiver is connected. Consult the factory or an experiencedradio/TV technician for help.

Navigation menu