HUIZHOU GAOSHENGDA TECHNOLOGY BT02B150 Bluetooth Module User Manual 4 BT02B150 Usermanual

HUIZHOU GAOSHENGDA TECHNOLOGY CO., LTD Bluetooth Module 4 BT02B150 Usermanual

Manual

PRODUCTS USERMANUAL PAGE 1 OF 1 BT02B150 Version 1.0 Bluetooth 4.0 Module Model Number: BT02B150 GSD BT02B150 is to specify the product requirements for Bluetooth 4.0 Module. This Card is based on Broadcom BCM20705 chipset that can support BT2.1+EDR/BT3.0+HS and BT4.0+EDR. ◆ Bluetooth 4.0+EDR compliant ◆Programmable output power control meets Class1,Class2,or Class3 requirements. ◆Use supply voltages up to 5.5V. ◆Supports Broadcom SmartAudioTM,wide-band speech,SBC codec,and packet lose concealments. ◆Ultra-low power consumption. ◆ARMTDMI-STM-based microprocessor with integrated ROM and RAM ◆Supports mobile and PC applications without external memory. Product Features Product Description
PRODUCTS USERMANUAL PAGE 2 OF 1 BT02B150 Version 1.0 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interferencereceived, including interference that may cause undesired operation. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void FCC Important Notes: (1) FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. Modular could be only used in mobile or fix device, and could not be used in any portable device.
PRODUCTS USERMANUAL PAGE 3 OF 1 BT02B150 Version 1.0Caution! The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment. (2) Co-location Warning: This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. (3) OEM integration instructions: This device is intended only for OEM integrators under the following conditions: The thetransmitter module may not be co-located with any other transmitter or antenna. The module shall be only used with the intergral antenna(s) that has been originally tested and certified with this module. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirementsrequired with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). (4) Validity of using the module certification: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization for this module in combination with the host equipment is no longer considered valid and the FCC ID of the module cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. (5) End product labeling: The final end product must be labeled in a visible area with the following: “Contains Transmitter Module FCC ID: 2ACVA-BT02B150”. (6) Information that must be placed in the end user manual: The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

Navigation menu