HARRIS TR-0150-E XL-185P, VHF, PORTABLE LAND MOBILE RADIO User Manual

HARRIS CORPORATION XL-185P, VHF, PORTABLE LAND MOBILE RADIO

UserManual.wiki >

TR 0150 E User Manual

User Manual

Operator’s Manual 14221-1800-2000 Rev. F, March 2017 XL-200P Full-Spectrum Multiband XL-185P Single Band Portable Radios

14221-1800-2000, Rev. F 3 This device is a RF transceiver intended for land mobile radio applications. The device may have use restrictions, which require that the national authority be contacted for any system licensing requirements, frequency use, allowable power level, etc.

14221-1800-2000, Rev. F 4

14221-1800-2000, Rev. F 5 DECLARATION OF CONFORMITY Česky [Czech] Harris Corporation tímto prohlašuje, že tento XL-200P je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede Harris Corporation erklærer herved, at følgende udstyr XL-200P overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch [German] Hiermit erklärt Harris Corporation, dass sich das Gerät XL-200P in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti [Estonian] Käesolevaga kinnitab Harris Corporation seadme XL-200P vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. English Hereby, Harris Corporation, declares that this XL-200P is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Español [Spanish] Por medio de la presente Harris Corporation declara que el XL-200P cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Ελληνική [Greek] ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Harris Corporation ΔΗΛΩΝΕΙ ΟΤΙ XL-200P ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ. Français [French] Par la présente Harris Corporation déclare que l'appareil XL-200P est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano [Italian] Con la presente Harris Corporation dichiara che questo XL-200P è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian] Ar šo Harris Corporation deklarē, XG 25P UHF-L(378-470 MHz), 7/800 (764-870MHz) atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. Lietuvių [Lithuanian] Šiuo Harris Corporation deklaruoja, kad šis XL-200P atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederlands [Dutch] Hierbij verklaart Harris Corporation dat het toestel XL-200P in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti [Maltese] Hawnhekk, Harris Corporation, jiddikjara li dan XL-200P jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Magyar [Hungarian] Alulírott, Harris Corporation nyilatkozom, hogy a XL-200P megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Polski [Polish] Niniejszym Harris Corporation oświadcza, że XL-200P jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Português [Portuguese] Harris Corporation declara que este XL-200P está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Slovensko [Slovenian] Harris Corporation izjavlja, da je ta XL-200P v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. Slovensky [Slovak] Harris Corporation týmto vyhlasuje, že XL-200P spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES. Suomi [Finnish] Harris Corporation vakuuttaa täten että XL-200P tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Svenska [Swedish] Härmed intygar Harris Corporation att denna XL-200P står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. Íslenska [Icelandic] Hér með lýsir Harris Corporation yfir því að XL-200P er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC. Norsk [Norwegian] Harris Corporation erklærer herved at utstyret XL-200P er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.

14221-1800-2000, Rev. F 6 TABLE OF CONTENTS Section Page 1. REGULATORY AND SAFETY INFORMATION ........................................................................... 11 1.1 SAFETY CONVENTIONS ........................................................................................................ 11 1.2 SAFETY TRAINING INFORMATION .................................................................................... 11 1.2.1 RF Exposure Guidelines ................................................................................................ 12 1.2.2 Electromagnetic Interference/Compatibility .................................................................. 13 1.3 REGULATORY APPROVALS ................................................................................................. 14 1.3.1 Part 15 ............................................................................................................................ 14 1.3.2 Industry Canada ............................................................................................................. 14 1.4 OPERATING TIPS .................................................................................................................... 14 1.4.1 Efficient Radio Operation .............................................................................................. 14 1.4.2 Antenna Care and Replacement ..................................................................................... 14 1.4.3 Electronic Devices ......................................................................................................... 15 1.4.4 Aircraft ........................................................................................................................... 15 1.4.5 Electric Blasting Caps .................................................................................................... 15 1.4.6 Potentially Explosive Atmospheres ............................................................................... 15 2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ ....................................... 16 2.1 CONVENTIONS SUR LES SYMBOLES DE SÉCURITÉ ...................................................... 16 2.2 RENSEIGNEMENTS SUR LA FORMATION SUR LA SÉCURITÉ ...................................... 16 2.2.1 Directives sur l’exposition aux RF ................................................................................ 17 2.2.2 Interférence/Compatibilité Électromagnétique .............................................................. 18 2.3 INTERFÉRENCE DES RADIOFRÉQUENCES ....................................................................... 18 2.3.1 Partie 15 de la FCC ........................................................................................................ 18 2.3.2 Industrie Canada ............................................................................................................ 18 2.4 CONSEILS D’UTILISATION ................................................................................................... 18 2.4.1 Utilisation Efficace de la Radio ..................................................................................... 18 3. HAZARDOUS LOCATIONS .............................................................................................................. 21 4. INTRODUCTION ................................................................................................................................ 23 4.1 DESCRIPTION .......................................................................................................................... 23 4.2 STORAGE GUIDELINES ......................................................................................................... 23 4.3 BASIC SETUP ........................................................................................................................... 24 4.3.1 Assemble the Radio ....................................................................................................... 24 4.3.2 Removing the Battery .................................................................................................... 25 4.3.3 Removing the Optional Belt Clip or D-Post .................................................................. 25 4.3.4 Install the SIM Card ....................................................................................................... 26 4.4 UNIVERSAL DEVICE CONNECTOR ..................................................................................... 27 4.5 CLEANING ................................................................................................................................ 27 4.6 OPTIONS AND ACCESSORIES .............................................................................................. 28 4.7 RELATED PUBLICATIONS .................................................................................................... 30 5. BASIC OPERATION ........................................................................................................................... 31 5.1 RADIO CONTROLS .................................................................................................................. 31 5.2 SOFT DTMF KEYPAD ............................................................................................................. 33 5.3 BEFORE FIRST USE ................................................................................................................. 33 5.4 POWER ON AND SET VOLUME ............................................................................................ 34 5.5 RADIO DISPLAYS .................................................................................................................... 34 5.5.1 Top Display ................................................................................................................... 34 5.5.2 Front Display ................................................................................................................. 35 5.6 MANDOWN ............................................................................................................................... 37

14221-1800-2000, Rev. F 7 TABLE OF CONTENTS Section Page 5.7 STATUS MESSSAGES ............................................................................................................. 37 5.8 PREDEFINED MENU LAYOUTS............................................................................................ 38 5.9 MENU ........................................................................................................................................ 39 5.10 ALERT TONES.......................................................................................................................... 42 5.11 SELECT ZONE/SYSTEM ......................................................................................................... 43 5.12 SELECT GROUP/CHANNEL AND BANK ............................................................................. 44 5.13 LOCK/UNLOCK KEYPAD....................................................................................................... 44 5.14 GROUP CALLS ......................................................................................................................... 45 5.14.1 Transmit a Group Call ................................................................................................... 45 5.14.2 Receive a Group Call ..................................................................................................... 45 5.15 INDIVIDUAL CALLS ............................................................................................................... 46 5.15.1 Transmit an Individual Call ........................................................................................... 46 5.15.2 Receiving an Individual Call ......................................................................................... 46 5.16 USER PROFILES ....................................................................................................................... 47 5.17 NOISE CANCELLATION ......................................................................................................... 48 5.17.1 Enable Noise Cancellation ............................................................................................. 48 5.17.2 Using Noise Cancellation .............................................................................................. 49 5.17.3 The Effect of Distance from the Microphone ................................................................ 49 5.17.4 Primary versus Secondary Microphone ......................................................................... 49 5.17.5 When using an SCBA Mask .......................................................................................... 49 5.18 PTT OPTIONS ........................................................................................................................... 50 5.19 VOICE ANNUNCIATION ........................................................................................................ 50 5.20 ENABLE/DISABLE ENCRYPTION ........................................................................................ 51 5.21 TRANSMIT ENABLE/DISABLE ............................................................................................. 51 5.22 CHANNEL GUARD (ANALOG CONVENTIONAL ONLY) ................................................. 52 5.23 USE TALKAROUND TO BYPASS REPEATER (ANALOG AND P25 CONVENTIONAL ONLY) ........................................................................................................................................ 53 5.24 TYPE 99 OPERATION .............................................................................................................. 54 5.24.1 Enable/Disable Type 99 ................................................................................................. 54 5.24.2 Disable After PTT.......................................................................................................... 55 5.24.3 Auto Reset ..................................................................................................................... 55 5.25 CALL ALERT (PAGE) .............................................................................................................. 55 5.25.1 Send Alert ...................................................................................................................... 55 5.25.2 Receive Alert ................................................................................................................. 55 5.26 DTMF ......................................................................................................................................... 55 5.27 AUDIO PLAYBACK ................................................................................................................. 56 5.28 START SCAN ............................................................................................................................ 57 5.29 STOP SCAN ............................................................................................................................... 58 5.30 MONITOR AND SQUELCH TYPES (CONVENTIONAL ONLY) ........................................ 59 5.31 NUISANCE DELETE ................................................................................................................ 60 5.32 CONVENTIONAL FAILSOFT (EDACS ONLY) .................................................................... 61 5.33 EMERGENCY OPERATION .................................................................................................... 62 5.33.1 Declaring an Emergency Call ........................................................................................ 62 5.33.2 Receiving an Emergency Call ....................................................................................... 62 5.33.3 Stealth Emergency ......................................................................................................... 63 5.34 MDC-1200 (ANALOG CONVENTIONAL ONLY) ................................................................. 63 5.34.1 Normal PTT Operation .................................................................................................. 63 5.34.2 MDC PTT ID Receive Handling ................................................................................... 63

14221-1800-2000, Rev. F 8 TABLE OF CONTENTS Section Page 5.34.3 Emergency Declaration ................................................................................................. 63 5.35 BEON OPERATION .................................................................................................................. 64 6. ADVANCED OPERATIONS .............................................................................................................. 65 6.1 VIEW/CHANGE PERSONALITIES ......................................................................................... 65 6.1.1 View Personalities ......................................................................................................... 65 6.1.2 Change Active Personality ............................................................................................ 66 6.2 SITUATIONAL AWARENESS (SA) – P25 CONVENTIONAL ONLY ................................. 67 6.3 USER-DEFINED ZONES/SYSTEMS ....................................................................................... 68 6.3.1 Command Tactical Zone ................................................................................................ 68 6.3.2 Mixed System Zone ....................................................................................................... 69 6.4 CH INFO MENU ........................................................................................................................ 70 6.5 AUDIO SETTINGS .................................................................................................................... 70 6.6 DISPLAY SETTINGS ................................................................................................................ 71 6.7 GPS SETTINGS ......................................................................................................................... 72 6.8 POSITION INFO ........................................................................................................................ 72 6.9 WI-FI .......................................................................................................................................... 73 6.10 BLUETOOTH ............................................................................................................................ 74 6.10.1 Enable Bluetooth ........................................................................................................... 74 6.10.2 Pair Devices ................................................................................................................... 75 6.11 CLOCK SETTINGS ................................................................................................................... 76 6.12 BATTERY INFO ........................................................................................................................ 76 6.13 SELECT LANGUAGE............................................................................................................... 77 6.14 SET UP SCAN ........................................................................................................................... 77 6.14.1 Default, Priority 1, and Priority 2 Channels .................................................................. 78 6.14.2 Trunked/Conventional Scanning ................................................................................... 78 6.14.3 Vote Scan (Analog and P25 Conventional Only) .......................................................... 79 6.14.4 Edit Scan List ................................................................................................................. 79 6.14.5 Set or Remove Priority 1 and Priority 2 Channels ......................................................... 80 6.14.6 Custom Scan Lists ......................................................................................................... 81 6.14.7 Wide Area System Scan (P25 Trunked and EDACS) ................................................... 83 6.15 RADIO STATUS ........................................................................................................................ 83 6.16 RADIO MESSAGE .................................................................................................................... 84 6.17 RADIO TEXTLINK ................................................................................................................... 84 6.17.1 Radio TextLink Messages ............................................................................................. 85 6.17.2 Radio TextLink Forms ................................................................................................... 85 6.17.3 View Received Messages .............................................................................................. 86 6.18 FAULTS/ALERTS ..................................................................................................................... 86 6.19 TONE ENCODE ........................................................................................................................ 87 6.20 ENCRYPTION ........................................................................................................................... 87 6.20.1 Create and Load Keys .................................................................................................... 87 6.20.2 Zeroize Keys from Radio ............................................................................................... 88 6.20.3 Protected Keys ............................................................................................................... 88 6.20.4 Global Encryption .......................................................................................................... 88 6.20.5 Select Keyset ................................................................................................................. 89 6.20.6 View Key List ................................................................................................................ 90 6.20.7 Delete Individual Keys .................................................................................................. 90 6.20.8 OTAR Configuration ..................................................................................................... 91 7. PROGRAMMING ................................................................................................................................ 92

14221-1800-2000, Rev. F 9 TABLE OF CONTENTS Section Page 7.1 PROGRAMMING VIA RPM2 .................................................................................................. 92 7.2 EDIT CHANNEL (ANALOG AND P25 CONVENTIONAL ONLY) ..................................... 92 7.3 OTAP .......................................................................................................................................... 94 7.4 PROGRAMMABLE BUTTONS AND SWITCHES ................................................................. 94 7.4.1 Programmable Buttons .................................................................................................. 94 7.4.2 Programmable A/B (Ø/O) Switch ................................................................................. 96 7.4.3 Programmable A/B/C/D Switch .................................................................................... 96 7.5 PROGRAMMABLE ICONS ...................................................................................................... 97 7.5.1 Top display .................................................................................................................... 97 7.5.2 Front display .................................................................................................................. 98 8. REFERENCE ...................................................................................................................................... 100 8.1 MARINE FREQUENCIES ...................................................................................................... 100 8.2 NARROWBANDING .............................................................................................................. 105 9. GLOSSARY ........................................................................................................................................ 106 10. BASIC TROUBLESHOOTING ........................................................................................................ 109 10.1 ERROR MESSAGES ............................................................................................................... 109 10.2 OTAR ERRORS/INFORMATION .......................................................................................... 110 11. TECHNICAL ASSISTANCE ............................................................................................................ 111 12. WARRANTY ...................................................................................................................................... 111 APPENDIX A WI-FI PROGRAMMING ......................................................................................... 112 LIST OF FIGURES Page Figure 4-1: Radio Assembly .......................................................................................................................... 24 Figure 4-2: Remove the Battery ..................................................................................................................... 25 Figure 4-3: Remove Belt Clip ........................................................................................................................ 25 Figure 4-4: SIM Card Installation .................................................................................................................. 26 Figure 4-5: Universal Device Connector ....................................................................................................... 27 Figure 5-1: Radio Controls ............................................................................................................................ 31 Figure 5-2: Using the Soft DTMF Keypad .................................................................................................... 33 Figure 5-3: Top Display ................................................................................................................................. 34 Figure 5-4: Sample Idle Front Display .......................................................................................................... 35 Figure 5-5: Using Noise Cancellation ............................................................................................................ 49 Figure 6-1: Enabling Wi-Fi ............................................................................................................................ 73 Figure 6-2: Wi-Fi Install Active ..................................................................................................................... 74 Figure A-1: Options  Network Configuration .......................................................................................... 113 Figure A-2: Wi-Fi Configuration ................................................................................................................. 113 Figure A-3: Service Name ........................................................................................................................... 114 Figure A-4: Enable Wi-Fi in RPM2 ............................................................................................................. 114 Figure A-5: Enable Wi-Fi Programming Mode on Radio ........................................................................... 115 Figure A-6: RPM2 Radio Tab: Wi-Fi .......................................................................................................... 116 LIST OF TABLES Page Table 1-2: RF Exposure Compliance Tested Distances (Worst Case Scenario) ............................................ 12 Table 1-3: Worst Case Reported SAR Level ................................................. Error! Bookmark not defined. Table 1-4: Simultaneous Transmission Scenarios ......................................................................................... 13

14221-1800-2000, Rev. F 10 TABLE OF CONTENTS Section Page Tableau 2-1 : Distances de test de conformité des expositions aux RF(pire des scénarios) .......................... 17 Table 4-1: Options and Accessories ............................................................................................................... 28 Table 5-1: Radio Controls, Indicators, and Connectors ................................................................................. 31 Table 5-2: Radio Icons ................................................................................................................................... 35 Table 5-3: Status Messages ............................................................................................................................ 37 Table 5-4: Predefined Menu Layouts ............................................................................................................. 38 Table 5-5: Menu Navigation ......................................................................................................................... 39 Table 5-6: Alert Tones ................................................................................................................................... 42 Table 7-1: Valid Frequency Ranges ............................................................................................................... 94 Table 7-2: Programmable Button Options ..................................................................................................... 95 Table 7-3: Programmable Ø/O Switch Options ............................................................................................. 96 Table 7-4: Single-Instance Features ............................................................................................................... 96 Table 7-5: Indexed Features ........................................................................................................................... 97 Table 8-1: Marine Frequencies .................................................................................................................... 100 Table 10-1: Displayed Error Messages, Reasons, and Resolutions ............................................................ 109 Table 12-1: Wi-Fi Feature Support .............................................................................................................. 116 Harris Corporation, Public Safety and Professional Communications (PSPC) Business continually evaluates its technical publications for completeness, technical accuracy, and organization. You can assist in this process by submitting your comments and suggestions to the following: Harris Corporation fax your comments to: 1-434-455-6851 PSPC Business or Technical Publications e-mail us at: PSPC_TechPubs@harris.com 221 Jefferson Ridge Parkway Lynchburg, VA 24501

14221-1800-2000, Rev. F 11 1. REGULATORY AND SAFETY INFORMATION 1.1 SAFETY CONVENTIONS The following conventions are used throughout this manual to alert the user to general safety precautions that must be observed during all phases of operation, service, and repair of this product. Failure to comply with these precautions or with specific warning elsewhere in this manual violates safety standards of design, manufacture, and intended use of the product. Harris assumes no liability for the customer’s failure to comply with these standards. The WARNING symbol calls attention to a procedure, practice, or the like, which, if not correctly performed or adhered to, could result in personal injury. Do not proceed beyond a WARNING symbol until the conditions identified are fully understood or met. The CAUTION symbol calls attention to an operating procedure, practice, or the like, which, if not performed correctly or adhered to, could result in damage to the equipment or severely degrade the equipment performance. The NOTE symbol calls attention to supplemental information, which may improve system performance or clarify a process or procedure. 1.2 SAFETY TRAINING INFORMATION The Harris XL-200P/XL-185P portable radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only,” meaning it must be used only during the course of employment by individuals aware of the hazards and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment. The XL-200P/XL-185P portable radio has been tested and complies with the FCC RF exposure limits for “Occupational Use Only.” In addition, this Harris radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans: • FCC KDB Publication 447498 General RF Exposure Guidance • American National Standards Institute (C95.1 – 19921), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. • American National Standards Institute (C95.3 – 1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields – RF and Microwave. • IC Standard RSS-102. Radiofrequency Exposure Compliance of Radiocommunication Apparatus (All Frequency Bands). • European Council Directive 89/391/EEC. 1 Tested to ANSI C95.1-1992 in compliance with 47 CFR 2.1093. Meets or exceeds safety requirements of ANSI C95.1-2005. WARNINGCAUTIONNOTEWARNING

14221-1800-2000, Rev. F 12 1.2.1 RF Exposure Guidelines To ensure that exposure to RF electromagnetic energy is within the EU/AU/FCC/IC allowable limits for occupational use, always adhere to the following guidelines: • DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may also cause the FCC RF exposure limits to be exceeded. A proper antenna is the antenna supplied with this radio by Harris or an antenna specifically authorized by Harris for use with this radio. (Refer to Table 4-1.) • DO NOT transmit for more than 50% of total radio use time (“50% duty cycle”). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the “TX” indicator appears in the display. The radio will transmit by pressing the “PTT” (Push-To-Talk) button. • ALWAYS transmit using low power when possible. In addition to conserving battery charge, low power can reduce RF exposure. • ALWAYS use Harris authorized accessories (antennas, batteries, belt clips, speaker/mics, etc.). Use of unauthorized accessories may cause the FCC Occupational/Controlled Exposure RF compliance requirements to be exceeded. (Refer to Table 1-1.) • As noted in Table 1-1, ALWAYS keep the housing of the transmitter AT LEAST 0.47 inches (1.2 cm) from the body and at least 0.98 in (2.5 cm) from the face when transmitting to ensure EU/AU/FCC/IC RF exposure compliance requirements are not exceeded. However, to provide the best sound quality to the recipients of your transmission, Harris recommends you hold the microphone at least 2 in (5 cm) from mouth, and slightly off to one side. • Refer to Standard EN 62311:2008. Table 1-1: RF Exposure Compliance Tested Distances (Worst Case Scenario) RADIO FREQUENCY Body2 Face VHF (136 - 174 MHz) 0.47 in (1.2 cm) 0.98 in (2.5 cm) UHF (378 - 522 MHz) 0.47 in (1.2 cm) 0.98 in (2.5 cm) 700/800 MHz (768 - 776 MHz) (798 - 806 MHz) (806 - 824 MHz) (851 - 870 MHz) 0.47 in (1.2 cm) 0.98 in (2.5 cm) 900 MHz (935-944 MHz) (896-902 MHz) 0.47 in (1.2 cm) 0.98 in (2.5 cm) 2400 MHz (2412 - 2472 MHz) 0.47 in (1.2 cm) 0.98 in (2.5 cm) 5 GHz (5.18 - 5.825 GHz) 0.47 in (1.2 cm) 0.98 in (2.5 cm) 2 This is worst case based on the thinnest body mount accessory (belt clip). CAUTION

14221-1800-2000, Rev. F 13 SAR Evaluation: 1g averaged, 50% PTT Duty Factor, Occupational/Controlled Exposure. This device contains multiple transmitters that may operate simultaneously, see Table 1-3 Simultaneous Transmission Scenarios for the capable transmit configurations. Table 1-2: Simultaneous Transmission Scenarios NO. CAPABLE TRANSMIT CONFIGURATION HEAD BODY-WORN ACCESSORY 1 LTE B13/14/4 + VHF YES YES 2 LTE B13/14/4 + UHF YES YES 3 LTE B4 + 700 MHz YES YES 4 LTE B13/14/4 + 800 MHz YES YES 5 LTE B13/14/4 + Bluetooth YES YES 6 LTE B13/14/4 + 2.4 GHz WLAN YES YES 7 LTE B13/14/4 + 5 GHz WLAN YES YES 8 LTE B13/14/4 + VHF + Bluetooth YES YES 9 LTE B13/14/4 + UHF + Bluetooth YES YES 10 LTE B4 + 700 MHz + Bluetooth YES YES 11 LTE B13/14/4 + 800 MHz + Bluetooth YES YES 12 LTE B13/14/4 + VHF + WLAN YES YES 13 LTE B13/14/4 + UHF + WLAN YES YES 14 LTE B4 + 700 MHz + WLAN YES YES 15 LTE B13/14/4 + 800 MHz + WLAN YES YES 16 LTE B13/14/4 + 900 MHz (XL-185P Only) YES YES 17 LTE B13/14/4 + 800 MHz + Bluetooth YES YES 18 LTE B13/14/4 + 800 MHz + WLAN YES YES LTE B13/14 + 700 MHz combination is not supported by this device. The information in this section provides the information needed to make the user aware of RF exposure, and what to do to assure that this radio operates within the FCC RF exposure limits. 1.2.2 Electromagnetic Interference/Compatibility During transmissions, this Harris radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites. NOTENOTE

14221-1800-2000, Rev. F 14 1.3 REGULATORY APPROVALS Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. 1.3.1 Part 15 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. 1.3.2 Industry Canada This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. 1.4 OPERATING TIPS Antenna location and condition are important when operating a portable radio. Operating the radio in low-lying areas or terrain, under power lines or bridges, inside of a vehicle, or in a metal framed building can severely reduce the range of the unit. Mountains can also reduce the range of the unit. In areas where transmission or reception is poor, some improvement may be obtained by ensuring that the antenna is vertical. Moving a few yards in another direction or moving to a higher elevation may also improve communications. Vehicular operation can be aided with the use of an externally mounted antenna. Battery condition is another important factor in the trouble free operation of a portable radio. Always properly charge the battery. 1.4.1 Efficient Radio Operation Keep the antenna in a vertical position when receiving or transmitting a message. Do NOT hold onto the antenna when the radio is powered on! 1.4.2 Antenna Care and Replacement Do not use the portable radio with a damaged or missing antenna. A minor burn may result if a damaged antenna comes into contact with the skin. Replace a damaged antenna immediately. Operating a portable radio with the antenna missing could cause personal injury, damage the radio, and may violate FCC regulations. WARNINGWARNING

14221-1800-2000, Rev. F 15 Use only the supplied or approved antenna. Unauthorized antennas, modifications, or attachments could cause damage to the radio unit and may violate FCC regulations. (Refer to Table 4-1.) 1.4.3 Electronic Devices RF energy from portable radios may affect some electronic equipment. Most modern electronic equipment in cars, hospitals, homes, etc. is shielded from RF energy. However, in areas in which you are instructed to turn off two-way radio equipment, always observe the rules. If in doubt, turn it off! 1.4.4 Aircraft • Always turn off a portable radio before boarding any aircraft! • Use it on the ground only with crew permission. • DO NOT use while in-flight!! 1.4.5 Electric Blasting Caps To prevent accidental detonation of electric blasting caps, DO NOT use two-way radios within 1000 feet of blasting operations. Always obey the "Turn Off Two-Way Radios" signs posted where electric blasting caps are being used (OSHA Standard: 1926.900). 1.4.6 Potentially Explosive Atmospheres Areas with potentially explosive atmospheres are often, but not always, clearly marked. These may be fueling areas, such as gas stations, fuel or chemical transfer or storage facilities, and areas where the air contains chemicals or particles, such as grain, dust, or metal powders. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Turn off two-way radios when in any area with a potentially explosive atmosphere. It is rare, but not impossible that a radio or its accessories could generate sparks. CAUTIONCAUTIONWARNINGWARNINGWARNING

14221-1800-2000, Rev. F 16 2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ 2.1 CONVENTIONS SUR LES SYMBOLES DE SÉCURITÉ Les conventions suivantes sont utilisées dans le présent manuel pour avertir l’utilisateur des précautions générales de sécurité qui doivent être observées pendant toutes les phases d’opération, d’entretien et de réparation de ce produit. Le non-respect de ces précautions ou d’avertissements précisés ailleurs enfreint les normes de sécurité de la conception, de la fabrication et de l’utilisation prévue du produit. Harris n’assume aucune responsabilité pour le non-respect de ces normes par le client. Le symbole MISE EN GARDE attire l’attention sur une procédure ou une pratique qui, si elle n’est pas correctement effectuée ou observée, pourrait entraîner une blessure personnelle. Ne pas poursuivre au-delà d’un symbole de MISE EN GARDE avant que les conditions identifiées soient complètement comprises ou satisfaites. Le symbole AVERTISSEMENT attire l’attention sur une procédure ou une pratique opérationnelle qui, si elle n’est pas correctement effectuée ou observée, pourrait entraîner un bris d’équipement ou une importante baisse de rendement de l’équipement. Le symbole REMARQUE attire l’attention sur des renseignements supplémentaires qui peuvent améliorer le rendement du système ou clarifier un processus ou une procédure. 2.2 RENSEIGNEMENTS SUR LA FORMATION SUR LA SÉCURITÉ La radio portative Harris XL-200P/XL-185P produit de l’énergie électromagnétique des RF lorsqu’en mode de transmission. Cette radio est conçue et classée pour une « Utilisation professionnelle seulement », ce qui signifie qu’elle ne doit être utilisée que dans le cadre d’un emploi par des individus conscients des risques et des moyens de limiter ceux-ci. Cette radio N’EST PAS conçue pour une utilisation par la « Population générale » dans un environnement non contrôlé. La radio portative XL-200P/XL-185P a été testée et est conforme aux limites d’exposition aux RF de la FCC pour une « Utilisation professionnelle seulement ». De plus, cette radio Harris est conforme aux normes et directives suivantes quant à l’énergie des RF et aux niveaux d’énergie électromagnétique, ainsi qu’à l’évaluation de ces niveaux pour l’exposition aux humains: • FCC KDB 447498 • American National Standards Institute (C95.1 – 1992), norme de l’IEEE sur les niveaux sécuritaires d’exposition humaine aux champs électromagnétiques des radiofréquences, 3 kHz à 300 GHz. • American National Standards Institute (C95.3 – 1992), pratique recommandée par l’IEEE pour la mesure des champs électromagnétiques potentiellement dangereux – RF et micro-ondes. MISE EN GARDEAVERTISSEMENTREMARQUEMISE EN GARDE

14221-1800-2000, Rev. F 17 2.2.1 Directives sur l’exposition aux RF Pour s’assurer que l’exposition à l’énergie électromagnétique des RF se situe dans les limites acceptables de la FCC pour l’utilisation professionnelle, respectez toujours les directives suivantes : • N’utilisez PAS la radio sans qu’une antenne appropriée y soit connectée, car ceci peut endommager la radio et également causer un dépassement des limites d’exposition aux RF de la FCC. Une antenne appropriée est celle fournie par Harris avec cette radio, ou une antenne spécifiquement autorisée par Harris pour être utilisée avec cette radio. (Reportez-vous à Tableau 2-1.) • Ne transmettez PAS pendant plus de 50 % de la durée d’utilisation totale de la radio (« cycle de service de 50 % »). La transmission pendant plus de 50 % du temps peut causer un dépassement des exigences de conformité de la FCC en matière d’exposition aux RF. La radio transmet lorsque l’indicateur « TX » apparaît sur l’affichage. La radio transmet lorsqu’on appuie sur le bouton « PTT » (bouton de microphone). • Transmettez TOUJOURS en basse puissance lorsque possible. En plus de préserver la charge de la pile, une faible puissance réduit l’exposition aux RF. • Utilisez TOUJOURS des accessoires autorisés Harris (antennes, piles, pinces de ceinture, haut-parleurs/micros, etc.). L’utilisation d’accessoires non autorisés peut entraîner un dépassement des exigences de conformité pour une exposition aux RF professionnelle ou contrôlée de la FCC. (Reportez-vous à Table 4-1.) • Tel qu’indiqué dans Tableau 2-1, conservez TOUJOURS l’appareil et son antenne à AU MOINS 1,2 cm du corps, et à au moins 2,5 cm du visage pendant la transmission, pour vous assurer de ne pas dépasser les exigences de conformité de la FCC en matière d’exposition aux RF. Cependant, pour offrir la meilleure qualité sonore aux auditeurs de votre transmission, Harris recommande de tenir le microphone à au moins 5 cm (2 po) de votre bouche et légèrement déplacé sur un côté. Tableau 2-1 : Distances de test de conformité des expositions aux RF(pire des scénarios) RADIOFRÉQUENCES Corps3 Visage VHF (136 - 174 MHz) 1,2 cm 2,5 cm UHF (378 - 522 MHz) 1,2 cm 2,5 cm 700/800 MHz (768 - 776 MHz) (798 - 806 MHz) (806 - 824 MHz) (851 - 870 MHz) 1,2 cm 2,5 cm 900 MHz (935-944 MHz) (896-902 MHz) 1,2 cm 2,5 cm 2400 MHz (2412 - 2472 MHz) 1,2 cm 2,5 cm 3 Ce est le pire des cas basée sur le corps plus mince monter accessoire (clip ceinture). AVERTISSEMENT

14221-1800-2000, Rev. F 18 RADIOFRÉQUENCES Corps3 Visage 5 GHz (5.18 - 5.825 GHz) 1,2 cm 2,5 cm Dans cette section figurent les renseignements nécessaires pour sensibiliser l’utilisateur à l’exposition aux RF et sur ce qu’il faut faire pour s’assurer que cette radio fonctionne dans les limites d’exposition aux RF de la FCC. 2.2.2 Interférence/Compatibilité Électromagnétique Pendant les transmissions, cette radio Harris produit de l’énergie des RF qui peut causer de l’interférence avec d’autres appareils ou systèmes. Pour éviter de telles interférences, fermez la radio dans les zones où il est indiqué de le faire. N’utilisez PAS le transmetteur dans des zones sensibles aux radiations électromagnétiques, comme les hôpitaux, les avions et les sites de détonation. 2.3 INTERFÉRENCE DES RADIOFRÉQUENCES 2.3.1 Partie 15 de la FCC Cet appareil est conforme à la Partie 15 de la réglementation de la FCC. Le fonctionnement est soumis aux deux conditions suivantes : 1. Cet appareil ne doit pas causer une interférence nuisible; et 2. Cet appareil doit accepter toute interférence reçue, y compris une interférence qui peut causer un fonctionnement non souhaité. 2.3.2 Industrie Canada Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. 2.4 CONSEILS D’UTILISATION L’emplacement et l’état de l’antenne sont importants pour l’utilisation d’une radio portative. L’utilisation de la radio dans des zones de faible élévation, sous des lignes électriques ou des ponts, à l’intérieur d’un véhicule ou dans un immeuble à ossature métallique, peut réduire la portée de l’appareil de manière considérable. Les montagnes peuvent également réduire la portée de l’unité. Dans les zones où la transmission ou la réception est insatisfaisante, certaines améliorations peuvent être obtenues en s’assurant que l’antenne est verticale. Se déplacer de quelques mètres dans une autre direction ou à un emplacement plus élevé peut également améliorer les communications. L’utilisation d’une antenne fixée à l’extérieur peut faciliter le fonctionnement dans un véhicule. L’état de la pile est un autre facteur important d’une utilisation sans tracas d’une radio portative. Chargez toujours correctement la pile. 2.4.1 Utilisation Efficace de la Radio Gardez l’antenne dans une position verticale pendant la réception ou la transmission d’un message.

14221-1800-2000, Rev. F 19 Ne tenez PAS l’antenne lorsque la radio est allumée! 2.4.1.1 Entretien Et Remplacement De L’antenne N’utilisez pas la radio portative si son antenne est endommagée ou absente. Une brûlure légère peut se produire au contact d’une antenne endommagée avec la peau. Remplacez immédiatement une antenne endommagée. L’utilisation d’une radio portative alors que l’antenne est absente peut causer des blessures, endommager la radio et pourrait enfreindre la réglementation de la FCC. Utilisez seulement l’antenne fournie ou une antenne approuvée. Des antennes non autorisées, des modifications ou des ajouts à une antenne peuvent endommager la radio et enfreindre la réglementation de la FCC. (Reportez-vous à Table 4-1.) 2.4.1.2 Appareils Électroniques L’énergie des RF provenant de radios portatives peut affecter certains appareils électroniques. La majorité de l’équipement électronique moderne dans les voitures, les hôpitaux, les maisons, etc. est blindé contre l’énergie des RF. Cependant, dans les zones où l’on vous demande de fermer l’équipement de radio bidirectionnelle, respectez toujours les règles. En cas de doute, éteignez-le! 2.4.1.3 Avion • Éteignez toujours une radio portative avant d’embarquer à bord d’un avion! • Ne l’utilisez au sol qu’avec la permission de l’équipage. • NE l’utilisez PAS durant le vol! 2.4.1.4 Détonateurs Électriques Pour prévenir la détonation accidentelle des détonateurs électriques, n’utilisez PAS de radios bidirectionnelles à moins de 305 m (1 000 pi) des opérations de détonation. Respectez toujours les indications « Éteindre les radios bidirectionnelles » situées là où des détonateurs électriques sont utilisés. (Norme OSHA : 1926.900) MISE EN GARDEMISE EN GARDEAVERTISSEMENTAVERTISSEMENTMISE EN GARDEMISE EN GARDE

14221-1800-2000, Rev. F 20 2.4.1.5 Atmosphère Potentiellement Explosive Les zones ayant une atmosphère potentiellement explosive sont souvent, mais pas toujours, identifiées clairement comme telles. Il peut s’agir de zones d’alimentation en carburant, comme les postes d’essence, les installations de stockage ou de transfert de carburant ou de produits chimiques, ainsi que les zones dont l’air contient des produits chimiques ou des particules, comme des grains, de la poussière ou des poudres métalliques. Des étincelles dans de telles zones peuvent provoquer une explosion ou un incendie, causant ainsi des blessures ou même la mort. Éteignez les radios bidirectionnelles dans toute zone ayant une atmosphère potentiellement explosive. Il est rare, mais pas impossible qu’une radio ou ses accessoires produisent des étincelles. MISE EN GARDE

14221-1800-2000, Rev. F 21 3. HAZARDOUS LOCATIONS Radios ordered with the Class 1, Division 2 option are suitable for use in Class 1, Division 2, Groups A, B, C, and D or non-hazardous (unclassified) locations only. Les radios commandées avec l’option Classe 1, Division 2 sont adéquates pour utilisation en Classe 1, Division 2, Groupes A, B, C et D, ou en lieux non-hasardeux (non-classifiés) seulement EXPLOSION HAZARD – REPLACE BATTERY PACK ONLY IN AN AREA KNOWN TO BE NON-HAZARDOUS, AND ONLY WITH HARRIS PART NO. 14035-4010-01. AVERTISSEMENT – RISQUE D’EXPLOSION – LES BATTERIES DOIVENT ÊTRE REMPLACÉES DANS UNE ZONE RECONNUE NON-HASARDEUSE SEULEMENT, ET SEULEMENT AVEC UNE BATTERIE HARRIS PORTANT LE NUMÉRO DE PIÈCE 14035-4010-01. EXPLOSION HAZARD – Substitution of any component may impair suitability for Class I, Division 2. AVERTISSEMENT – RISQUE D’EXPLOSION – Une substitution de toute composante pourrait compromettre la convenance pour la Classe I, Division 2. EXPLOSION HAZARD – Do not exceed maximum battery charging current of 5.250 A or maximum charging voltage of 12.0 V DC at any time. CAUTION - The battery used in this device may present a risk of fire or explosion when heated above 100°C (212°F) or incinerated. Replace battery with Harris Part No. 14035-4010-01 only. Use of another battery may present a risk of fire or explosion. Battery replacement instructions: Remove battery by 1) depressing battery latches then 2) remove battery from radio chassis. Install replacement battery by inserting battery in radio chassis opening and depressing battery into chassis until both battery latches are engaged. Dispose of used battery promptly. Keep away from children. Do not disassemble and do not dispose of in fire. EXPLOSION HAZARD – In addition to any simple single-ended coil antenna, only the following Harris accessories may be used with this radio: PART NUMBER DESCRIPTION 12082-0600-01 Speaker Microphone 12082-0600-02 Speaker Microphone, Emergency Button 12082-0650-01 Microphone, Palm,2 Wire, Black 12082-0650-02 Microphone,Palm,2 Wire, Beige 12082-0650-03 Microphone, Mini-Lapel,3 Wire, Black 12082-0650-04 Microphone, Mini-Lapel,3 Wire, Beige 12082-0650-05 Earphone Kit, Black 12082-0650-06 Earphone Kit, Beige 12082-0650-07 Headset, In-Ear, Boom Mic, In-Line PTT 12082-0650-08 Headset, Lightweight, Over-the-Head, Single Ear, In-Line PTT WARNINGWARNINGWARNINGWARNINGWARNING

14221-1800-2000, Rev. F 22 PART NUMBER DESCRIPTION 12082-0650-09 Headset, Lightweight, Behind-the-Head, Dual Ear, In-Line PTT 12082-0650-10 Headset, Lightweight, Behind-the-Head, Dual Ear, Pigtail PTT 12082-0650-13 Headset, Heavy Duty, Behind-the-Head, w/PTT 12082-0650-14 Headset, Heavy Duty, Over-the-Head, w/PTT 12082-0650-15 Headset, Behind-the-Head, Boom Mic, Earpiece, w/PTT 12082-0650-16 Headset, Tactical, Boom Mic, Earpiece, w/PTT 12082-0650-17 Skull Mic, w/Body PTT and Earcup 12082-0650-18 Throat Mic, W/Acoustic Tube & Body PTT 12082-0650-19 Throat Mic, w/Acoustic Tube, Body and Ring PTT LS103239V1 Earphone, Lapel Microphone, 2.5mm LS103239V2 Earphone, Lapel Microphone, 2.5mm, RT Angle 12150-1000-01 Speaker Mic, Premium, Fire (FSM), Noise Cancelling

14221-1800-2000, Rev. F 23 4. INTRODUCTION 4.1 DESCRIPTION The XL-Series portable radios provide the advanced connectivity that first responders require while addressing evolving voice and data communications. They meet MIL-STD-810G for durability and are certified to more stringent MIL-STD parameters for contamination by fluids and explosive atmospheres. XL portable radios support P25 Trunking, P25 Conventional, Enhanced Digital Access Communications System (EDACS), analog conventional, and BeOn® over a Wi-Fi® or LTE network. EDACS operation is not supported in UHF or VHF. Refer to Feature Manual 14221-7200-6130 for details on configuring and using BeOn on the XL Series radios. Radio features include: • Extremely Rugged – exceeds the standards of other radios on the market. • Multiband Operation – supports any combination of VHF, UHF, and 700/800 MHz frequencies. Also allows different bands to be enabled for selected users. • Single-key DES Encryption – provides basic secure communications without having to buy the complete encryption option. • Instant Recall of Received Audio – allows user to replay the last transmission received to avoid unnecessary repetition. • Active Noise Cancellation – with three internal microphones to transmit intelligible audio from users in loud environments. • Built-in GPS – for location reporting and rapid response for emergencies. • Integrated Bluetooth® – for wireless interface to selected accessories. • Wi-Fi Connectivity – permits simple and easy radio software and personality updates. • Wi-Fi Access Point – Radios that include the LTE option can be configured via RPM2 to act as a Wi-Fi access point and/or router, providing access to broadband data for Wi-Fi devices. Refer to RPM2’s online help when configuring the radio for these functions. • Covert Mode – allows users to quickly configure the radio for operation in a covert environment. • Fully Programmable Keypad – each key can be programmed to a variety of functions. • 4-position switch – provides added configuration flexibility. • Unique User Interface – tools specially designed by first responders make radio operation simple and intuitive. An easy-to-read multi-color front display and a monochromatic top display with optional colored backlighting enhance communications for improved user safety. For optional accessories, refer to Table 4-1. Additional accessories may have been added since publication of this manual; contact Harris for more information. 4.2 STORAGE GUIDELINES Store your radio and batteries in a clean, cool (not exceeding 86 °F [+30 °C]), dry, and ventilated storage area. NOTE

14221-1800-2000, Rev. F 24 4.3 BASIC SETUP 4.3.1 Assemble the Radio Only use a Harris charger approved for the battery chemistry. Injury could occur from improper charger use. Do not over-tighten the antenna as damage could result. Please charge battery fully before first use. Due to government regulations, batteries ship in a discharged state and may require up to two (2) minutes in a charger for successful initialization. During initialization, the charger will not show any charge indication. After this initialization period, charging will resume normally. 1. Make sure batteries are charged per the manual supplied with the charger. 2. To attach optional belt clip, remove the existing tab from the back of the radio above the battery compartment. Slide the belt clip into the groove. 3. Lift clip, if installed, and slide top of battery into top of battery compartment at the rear of the radio. 4. Press down on bottom side of battery until it snaps into place. Figure 4-1: Radio Assembly WARNINGCAUTIONNOTE

14221-1800-2000, Rev. F 25 4.3.2 Removing the Battery To remove, press and hold the two tabs at the bottom of the battery and then pull battery up and out of the radio. Figure 4-2: Remove the Battery 4.3.3 Removing the Optional Belt Clip or D-Post Remove the battery before removing the belt clip or D-Post. To remove the belt clip, pry up on the metal spring towards the top of the battery compartment (see Figure 4-3) using a flat head screwdriver and slide the belt clip or D-Post out of the groove in the back of the radio. Figure 4-3: Remove Belt Clip

14221-1800-2000, Rev. F 26 4.3.4 Install the SIM Card Figure 4-4 shows how to install the SIM card in the LTE version of the radio. Figure 4-4: SIM Card Installation

14221-1800-2000, Rev. F 27 4.4 UNIVERSAL DEVICE CONNECTOR The Universal Device Connector (UDC) provides connections for external accessories such as a headset, a speaker-microphone, audio test box, audio test cables, and programming cables. The UDC is located on the right side of the radio, opposite the PTT Button. The UDC facilitates programming and testing the radio. The UDC pins perform different functions depending on the accessory attached to the UDC. Figure 4-5: Universal Device Connector 4.5 CLEANING Keep the exterior of the radio, battery, antenna, and radio accessories clean. Periodically clean using the following procedures: 1. To remove dust and dirt, clean using damp clean cloth (warm water and mild detergent soap). 2. Follow by wiping with damp (warm water) clean cloth. Wipe dry with clean cloth. 3. Remove the battery and wipe the battery and radio contacts using a soft dry cloth to remove dirt or grease. This will ensure efficient power transfer from the battery to the radio. 4. Remove any accessories and clean the UDC contacts using a clean dry cloth. When the UDC is not in use, cover the connector with the protective dust cap to prevent the build-up of dust or water particles. 5. If the radio is used in a harsh environment (such as driving rain, salt fog, etc.), it may be necessary to periodically dry and clean the battery and radio contacts with a soft dry cloth or soft-bristle non-metallic brush.

14221-1800-2000, Rev. F 28 For more rigorous cleaning, use the following procedure: Do not use chemical cleaners, spray, or petroleum-based products. They may damage the radio housing. We recommend using Chemtronics® Electro-Wash® PR (ES-1603) or equivalent. 1. Apply the cleaning solution to a clean damp cloth and clean the radio. Do not spray cleaning solution directly on radio. To clean the radio in the speaker and microphone areas, carefully wipe these areas but prevent the cleaning solution from entering the speaker or microphone openings. 2. Wipe off the radio with clean damp cloth using mild warm soapy water. 3. Follow up by wiping off the radio with clean damp cloth using warm water only. 4. Wipe dry with clean cloth. 4.6 OPTIONS AND ACCESSORIES Only use Harris approved accessories. Refer to Harris’ Product and Services catalog for the complete list of options and accessories available. Contact Harris for requirements not contained in this list: Always use the correct options and accessories (battery, antenna, speaker/mic, etc.) for the radio. Immersion rated options must be used with an immersion rated radio. Refer to Table 4-1. Table 4-1: Options and Accessories DESCRIPTION PART NUMBER OPTION NUMBER ANTENNAS Antenna, Full Spectrum XL-200P Only 14035-4000-01 XL-NC5Z Antenna, Whip Wideband 378-520 MHz, 762-870 MHz XL-200P Only 14035-4420-01 XL-NC8E Antenna, Whip, 1/4 Wave, 762-870 MHz XL-200P Only 14035-4440-02 XL-NC8F Antenna, Whip, 1/2 Wave, 762-870 MHz XL-200P Only 14035-4440-01 XL-NC8D Antenna, Whip, 1/4 Wave, 762-944 MHz XL-185P Only (Not approved w/LTE Option) 14035-4450-02 XL-NC9F Antenna, Whip, 1/2 Wave, 762-944 MHz XL-185P Only (Approved w/LTE Option) 14035-4450-01 XL-NC9D Antenna, 896-941 MHz XL-185P Only (Not approved w/LTE Option) KRE1011223/02 MAEX-NNC1Z BATTERIES/CHARGERS Battery, Lithium, Standard Capacity 14035-4010-01 XL-PA3V Battery, Li-Ion, 3100 mAH 14035-4010-04 XL-PA3V Battery, Li-Ion, 3100 mAH, UL 14035-4010-05 Charger, Single Bay 14035-1800-01 XL-CH4X Charger, Multi Bay 14035-1800-02 XL-CH5A Charger, Vehicular 14035-4100-01 XL-CH4W AUDIO ACCESSORIES Speaker Microphone 12082-0600-01 XL-AE9N Speaker Microphone, Emergency Button 12082-0600-02 XL-AE4B Speaker Microphone, Wireless, Bluetooth 12082-0681-01 XL-AE6K Speaker Microphone, Premium, Fire, Noise Cancelling 12150-1000-01 XL-AE1T Speaker Microphone, Premium, Fire, Noise Cancelling, High Visibility Yellow 12150-1000-05 XL-AE1X CAUTIONNOTECAUTION

14221-1800-2000, Rev. F 29 DESCRIPTION PART NUMBER OPTION NUMBER Microphone, Palm, 2-Wire, Black 12082-0650-01 XL-AE6G Microphone, Palm, 2-Wire, Beige 12082-0650-02 XL-AE6M Microphone, Mini-Lapel, 3-Wire, Black 12082-0650-03 XL-AE6H Microphone, Mini-Lapel, 3-Wire, Beige 12082-0650-04 XL-AE6N Earphone Kit, Black 12082-0650-05 Earphone Kit, Beige 12082-0650-06 Headset, In-Ear, Boom Mic, In-Line PTT 12082-0650-07 XL-AE2A Headset, Light Weight, Over-the-Head, Single Ear, In-Line PTT 12082-0650-08 XL-AE2B Headset, Light Weight, Behind-the-Head, Dual Ear, In-Line PTT 12082-0650-09 XL-AE2C Headset, Light Weight, Behind-the-Head, Dual Ear, Pig Tail PTT 12082-0650-10 XL-AE2D Headset, Light Weight, Behind-the-Head, Dual In-Ear, In-Line PTT 12082-0650-11 XL-AE2E Headset, Light Weight, Behind-the-Head, Dual In-Ear, Pig Tail PTT 12082-0650-12 XL-AE2F Headset, Heavy Duty, Behind-the-Head, w/PTT 12082-0650-13 XL-AE1P Headset, Heavy Duty, Over-the-Head, w/PTT 12082-0650-14 XL-AE1R Headset, BTH Boom Mic, Earpiece, w/PTT 12082-0650-15 XL-AE2G Headset, Tactical, Boom Mic, Earpiece, w/PTT 12082-0650-16 XL-AE1H Skull Mic, w/Body PTT, Earcup 12082-0650-17 XL-AE1L Throat Mic, w/Acoustic Tube, Body PTT 12082-0650-18 XL-AE1M Throat Mic, w/Acoustic Tube, body and Ring PTT 12082-0650-19 XL-AE1N Bluetooth, Covert, Earpiece/MIC/PTT, Radios 12082-0684-01 XL-AE1S Earphone, Lapel Microphone LS103239V1 XL-AE3Z Earphone, Speaker Mic, Right Angle, 2.5 MM LS103239V2 XL-AE1K MISCELLANEOUS ACCESSORIES Cable, Data Interface 12082-0445-A1 XL-CJ4A Cable, MATQ-03424, Test 12082-0435-A1 Cable, USB, Key Loading/Programming 12082-0410-A1 XL-CJ3A Cable, KVL, Key Loading 12082-0400-A1 XL-CJ3B Adapter, 6-Pin Hirose 14002-0197-01 XL-CJ4B Holster, Leather, Radio, Premium 14035-4200-01 Holster, Leather W/Rings, Radio, Premium 14035-4200-02 Holster, Nylon, Black, Radio, Premium 14035-4200-03 Holster, Ring, Leather, Radio, Premium 14035-4200-04 Case, Leather, Premium, Belt Loop, D-swivel 14035-4201-01 XL-HC4K Case, Leather, Premium, Shoulder Strap 14035-4201-02 XL-HC4L Case, Leather, Premium, Shoulder Strap 14035-4202-01 Holster, Leather W/Rings, Radio, Standard 14035-4202-02 Holster, Nylon, Black, Radio, Standard 14035-4202-03 Holster, Ring, Leather, Radio, Standard 14035-4202-04 Belt Loop, Leather, Premium 14002-0218-01 XL-HC4A D-Swivel 12082-3230-01 Strap, Shoulder CC103333V1 Metal Belt Clip 12082-1290-01 XL-HC3L Case, Leather, Premium, Shoulder Strap 14035-4201-02 XL-HC4L Belt Loop, Leather KRY1011609/1 Holster, Leather, Premium 14036-4000-01 Holster, Leather W/Rings, Premium 14036-4000-02 Side Connector Cover 12082-1398-01 XL-ZN7V

14221-1800-2000, Rev. F 30 4.7 RELATED PUBLICATIONS The following publications contain additional information about the radio and related products: MANUAL NUMBER DESCRIPTION 14221-1800-2010 Portable Radio Product Safety Manual 14221-1800-1000 XL-200P/XL-185P Portable Radio Quick Guide 14221-1800-2000 XL-200P/XL-185P Portable Radio Operator’s Manual 14221-1800-8000 XL-200P/XL-185P Portable Radio Software Release Notes MM1000019423 Key Manager and Key Admin Overview and Operation Manual MM1000019424 Key Manager and Key Loader Overview and Operation Manual 14221-1600-2090 Single-Bay Desktop Charger Operator Manual 14221-1600-2110 VC4000 Vehicular Charger Operator Manual 14221-7200-6110 Voice Annunciation Feature Manual 14221-2100-3000 Advanced Access Control/Radio Personality Manager Overview Manual 14221-1100-8170 Radio Personality Manager 2 (RPM2) Software Release Notes 14221-7200-6130 BeOn Configuration and Use Feature Manual The product safety manual and the quick guide are included with the radio equipment package when the radio ships from the factory. All publications listed above are available at www.pspc.harris.com via an Information Center login and Tech Link.

14221-1800-2000, Rev. F 31 5. BASIC OPERATION 5.1 RADIO CONTROLS Figure 5-1: Radio Controls Table 5-1 describes the default functions of buttons, knobs, and controls. Most can be programmed for different functions; see Section 7.4 for more information. Table 5-1: Radio Controls, Indicators, and Connectors CONTROL/INDICATOR FUNCTION Group/Channel Knob Selects groups/channels. Power/Volume Knob Turn clockwise to power on radio and increase volume of audio heard from speaker. Minimum volume levels may be programmed into the radio to prevent missed calls due to a low volume setting. A/B (Ø/O) Switch User-programmable switch (see Section 7.4.2). NOTE

14221-1800-2000, Rev. F 32 CONTROL/INDICATOR FUNCTION Microphone (Secondary) When noise cancellation is enabled, the secondary and primary microphones are used together to form a dual microphone system. Noise cancellation improves the quality of transmitted voice. When noise cancellation is disabled, only the primary microphone is used. See Section 5.17 for detailed information on using noise cancellation. A/B/C/D Switch User-programmable switch (see Section 7.4.3). By default, selects one of four channel banks (see Section 5.12). User-Programmable Buttons Used to select a commonly used function as an alternative to navigating menus. This is configured via programming using Radio Personality Manager 2 (RPM2). See Section 7.4.1 for the options that can be programmed to these buttons. Push-To-Talk (PTT) Button Press to transmit. Make sure Push-To-Talk (PTT) is enabled (Section 6.5). Battery Battery - Refer to Section 4.3 for battery connection and removal. Antenna Connector Antenna connector. Emergency Button Used to place radio in emergency mode (see Section 5.32). This button can be disabled via programming using RPM2. In addition, this button can be used in conjunction with a User-Programmable Button to clear emergencies if configured to do so. Indicator Light Emitting Diode (LED) Indicates radio status: • Red = actively transmitting. • Green = actively receiving. • Orange = actively transmitting encrypted. Top Display Shows summary of radio operation, including channel/talkgroup (which can be color coded), as well as a variety of programmable icons. Display orientation can be configured for viewing from the front or rear of the radio. (Section 6.6). Speaker Radio speaker which can be muted (Section 6.5). Adjust volume using the Power/Volume knob. Microphone (Primary) When noise cancellation is enabled, the primary and secondary microphones are used together to form a dual microphone system. Noise cancellation improves the quality of transmitted voice. When noise cancellation is disabled, only the primary microphone is used. See Section 5.8 for detailed information on using noise cancellation. Front Display Front display shows complete status and radio menus. User-Programmable Soft Keys User-programmable dynamic keys that have their current function labeled on the radio display directly above each button. See Section 7.4.1 for the options that can be programmed to these buttons. Menu/Select Button From the Main Display, press this button to access the menu. Also selects highlighted menu items.

14221-1800-2000, Rev. F 33 CONTROL/INDICATOR FUNCTION Navigation Buttons Navigates menu items. In addition: Press  while on the idle display to access Channel Information (see Section 6.4). Press  while on the idle display to display the functions assigned to programmable buttons (see Section 7.4). Press  to display Missed Call info. Press  to end or reject an I-Call. Keypad By default, used to enter text or numbers. Can be programmed for various functions (see Section 7.4). 5.2 SOFT DTMF KEYPAD The partial keypad model of the radio supports a “soft” DTMF keypad. This allows the radio user to utilize a graphical DTMF keypad in place of a physical DTMF keypad. On screens that require keypad entry, press the KEYPAD softkey to display the keypad. Use , , , and  to navigate, press the Menu/Select button to select highlighted digit, and then press the ENTER softkey. For example, when placing an Individual Call to a numeric address, the soft DTMF keypad can be used to enter the address as shown: Figure 5-2: Using the Soft DTMF Keypad 5.3 BEFORE FIRST USE Make sure the radio has: • Fully charged battery • Antenna attached • Personality and radio programmed using RPM2 • Encryption keys loaded if using encrypted channels • Personality activated

14221-1800-2000, Rev. F 34 5.4 POWER ON AND SET VOLUME The power switch and volume control are the same knob on top of the radio (see Figure 5-1). Turn the Power/Volume Knob clockwise to power on radio and increase the volume. A minimum volume level can be programmed into the radio to prevent missed calls due to a low volume setting. The radio can be programmed to require the entry of a PIN in order to operate the radio. Check with your System Administrator if you forget your PIN. As the PIN is entered, an asterisk is displayed for each digit; the actual value is not displayed. 5.5 RADIO DISPLAYS 5.5.1 Top Display The top display (Figure 5-3) shows a summary of status, such as channel number/bank, channel short name, battery, scanning, and emergency mode. The display can be configured for viewing from the front or rear of the radio (see Section 6.6). The channel short name is programmed using RPM2. Figure 5-3: Top Display NOTENOTE

14221-1800-2000, Rev. F 35 5.5.2 Front Display Figure 5-4 shows a sample front display while on the idle screen. The idle screen appears after power up or after exiting from the menus. Figure 5-4: Sample Idle Front Display The radio can be programmed to display the User ID on the System line of the display. Table 5-2 describes some of the icons that may be displayed by the radio. The radio menu also contains an icon glossary in the Utility Menu (see Section 5.8). Icons and their location can be customized using RPM2. Table 5-2: Radio Icons ICON DESCRIPTION ICON DESCRIPTION ICON DESCRIPTION (Blue) Trunked Signal Strength Bluetooth Enabled Monitor On (Red) TX Power (Blue) Bluetooth Connected VDOC (Green) Receive Signal Strength Encryption Enabled Receiving Data (No Color) Channel Idle Global Encryption Transmitting Data (Orange) Transmitting Encrypted OTAR Disabled Alert(s) Present Battery Fully Charged OTAR Registered Vote Scanning Battery Level 100% Capacity OTAR Registering Scanning Enabled Battery Level 75% Capacity OTAR Rekeying Emergency NOTE

14221-1800-2000, Rev. F 36 ICON DESCRIPTION ICON DESCRIPTION ICON DESCRIPTION Battery Level 50% Capacity Transmit Power Level High RX Mail Battery Level 25% Capacity Transmit Power Level Low Noise Cancellation Enabled Battery Level 5% Capacity (Low Battery Audio Indicator) RX Only Fire Speaker Mic Attached Battery Level Battery Exhausted (RX-Only State) Speaker Muted Nuisance Channel Battery Charging TX Disabled Conventional Site Unregistered Talkaround Enabled Tones Disabled Conventional Site Registered Failsoft PTT Disabled Type 99 Enabled LTE – Registered Foreign Network LTE – Denied or Unknown Registration Status GPS Tracking LTE – Registered Home LTE – No Signal Wi-Fi Clients Connected

14221-1800-2000, Rev. F 37 5.6 MANDOWN If enabled via radio programming, the following conditions can be configured to trigger a Mandown condition: • MOTION - Mandown is declared with lack of motion. • TILT - Mandown is declared when the radio is tilted. • BOTH - Mandown is declared by radio tilting and lack of motion. This can be useful if, for example, a radio user is in danger and has not moved for a certain amount of time. If the user’s movement falls below the configured level, then a tone begins playing. An Emergency is declared on the channel/group based on the radio’s Emergency configuration. 5.7 STATUS MESSSAGES The radio may display various radio Status Messages during operation. These messages are described in Table 5-3. Table 5-3: Status Messages MESSAGE DESCRIPTION PTT DENIED P25 Trunked and EDACS - The radio or talkgroup is not authorized to operate on the selected system and/or talkgroup. CALL QUEUED P25 Trunked and EDACS - The system has placed the call in a request queue. SYSTEM BUSY P25 Trunked and EDACS - The system is busy, no channels are currently available, the queue is full, or an individual call is being attempted to a radio that is currently transmitting. SCANNING The radio is scanning. TX EMERGENCY An emergency call is being transmitted. RX EMERGENCY An emergency call is being received. The radio displays the unit name or unit ID. WIDE AREA SCAN P25 Trunked and EDACS - The radio has entered the Wide Area Scan mode to search for a new system. INVALID TALKGROUP P25 Trunked and EDACS - The current talkgroup is not valid for the current system. This could happen if the site denies registration due to an unrecognized talkgroup ID. INVALID UNIT P25 Trunked and EDACS - The current unit is not valid for the current system. REGISTERING P25 Trunked only - Displayed when the radio is performing a registration/affiliation on a P25 trunking site. CTRL CHANNEL SCAN P25 Trunked and EDACS - The control channel is lost and the radio has entered the Control Channel Scan mode to search for the control channel (usually out of range indication). BAND SCANNING P25 Trunked and EDACS - Only displayed if the system is configured for "EnhancedCC" mode of operation. When the radio cannot find a Control Channel in either the trunked frequency set or the list of discovered adjacencies, the radio is able to perform a full spectrum frequency scan to find a new Control Channel. MISSED CALL P25 Modes and EDACS - Another user has tried to call or page this radio. The user can view who the caller was by pressing the key. OTAR REKEY COMPLETE OTAR Rekey operation completed successfully.

14221-1800-2000, Rev. F 38 5.8 PREDEFINED MENU LAYOUTS Depending on radio programming, some menu options described in this manual may not be available. The radio supports three predefined menu layouts: Full, Custom, and Restricted. Table 5-4 details what is available in each layout: The Custom predefined menu layout allows the administrator to customize the list of menu items that are available to the radio user. Table 5-4 lists the default settings. Table 5-4: Predefined Menu Layouts MENU FULL CUSTOM (Default Settings) RESTRICTED Call Menu Yes Yes Yes Exit Emergency Yes Yes Yes Talkaround Yes Yes Yes Individual Call Yes Yes Yes Change Talkgroup Yes Yes Yes Call Alert/Page Yes Yes Yes Channel Guard Yes Yes Yes Audio Playback Yes Yes No Tone Encode Yes Yes Yes T99 Yes Yes Yes Audio Settings Yes No No Display Settings Yes Yes Yes GPS Settings Yes No No Clock Settings Yes Yes No Bluetooth Settings Yes Yes No Scan Menu Yes Yes Yes Enable/Disable Scan Yes Yes Yes View Scan List Yes Yes No Edit Zone Scan List Yes No No View Custom Channels Yes Yes No Edit Custom Scan List Yes No No Custom Scan Yes Yes No Site Roam Yes Yes No Security Menu Yes Yes Yes Encryption Enable Yes Yes Yes Zeroize Yes No No Global CKR Enable Yes No No GCKR Key Select Yes No No Active Key Set Yes Yes Yes Key List Yes Yes No OTAR Enable Yes Yes No OTAR Rekey Yes Yes Yes NOTE

14221-1800-2000, Rev. F 40 MENUS DESCRIPTION SCAN MENU: START SCAN/STOP SCAN Start or stop scan operation. See Sections 5.28 and 5.29. SCAN LISTS View/Edit available scan lists. See Section 6.14. ASSIGNED CUSTOM LIST Create, View, and Edit Custom Scan Lists. See Section 6.14.6. SITE ROAMING Enable/Disable Wide Area System Scan. See Section 6.14.7. SECURITY MENU: ZEROIZE KEYS Removes all encryption keys from the radio. See Section 6.20.2. ENCRYPTION Enable/Disable encryption. See Section 5.20. GLOBAL ENCRYPTION Enable/Disable Global Encryption. See Section 6.20.4. GLOBAL KEY Select the Global Key. Only available if Global Encryption is Enabled. See Section 6.20.4. ACTIVE KEYSET Select the Active Keyset. See Section 6.20.5. KEY LIST View available key lists. See Section 6.20.6. OTAR Enable/disable Over-the-Air Rekeying (OTAR). See Section 6.20.7. OTAR REKEY Request that the KMF updates the keys in the radio. See Section 6.20.7. MESSAGES MENU: RADIO STATUS Used to send a particular status condition to the site without making a voice call. See Section 6.15. RADIO MESSAGE Used to send a particular message to the site without making a voice call. See Section 6.16. TEXTLINK MESSAGES Allows the user to send a Radio TextLink message. See Section 6.17. TEXTLINK FORMS Allows the user to send a Radio TextLink form. See Section 6.17. TEXTLINK MAILBOX Contains received Radio TextLink messages. See Section 6.17. FAULTS/ALERTS Displays radio faults and alerts. See Section 6.18. UTILITY MENU: AUDIO SETTINGS: • SPEAKER (MUTE/UNMUTE) Mute or unmute the speaker audio. • NOISE CANCELLATION Enable or disable Noise Cancellation. See Section 5.17. • PTT Enable or disable Push-To-Talk (PTT). Disable PTT to prevent accidental keying, such as when radio is in the holster or you are getting into a car. • TONES Enable or disable radio side tones. • KEYPAD TONES Enable or disable tones that sound when the radio’s keypad buttons are pressed. DISPLAY SETTINGS: • COLOR SCHEME Press the Menu/Select button to toggle the front and top display’s COLOR SCHEME for optimum visibility in day or night conditions (NORMAL or INVERTED). • FRONT BACKLIGHT Press the Menu/Select button to toggle the front display backlighting between ON/OFF/MOMENTARY/MOMENTARY (OFF). • FRONT BRIGHTNESS Press  or  to dim or brighten the display. • FRONT TIMEOUT When the FRONT BACKLIGHT setting is MOMENTARY, this value specifies how long the radio needs to be inactive before the front display’s backlight turns off. Press  or  to change the time in 0.5 second increments. • FRONT DISPLAY OFF Turns the front display off completely. Press the Menu/Select button to turn the front display back on. • TOP BACKLIGHT Press the Menu/Select button to toggle the top display backlighting ON/OFF/MOMENTARY. • TOP BRIGHTNESS Press  or  to dim or brighten the display. • TOP TIMEOUT When the TOP BACKLIGHT setting is MOMENTARY, this value specifies how long the radio needs to be inactive before the top display’s backlight turns off. Press  or  to change the time in 0.5 second increments. • TOP ORIENTATION Set orientation of top display to be viewed from radio: FRONT, BACK, or AUTO. When AUTO is selected, the radio changes the top display to be viewed from the back if an external microphone or speaker is attached. Otherwise, the display can be viewed from the front. • INDICATOR LED Press the Menu/Select button to toggle the indicator LED ON or OFF. BLUETOOTH: • ENABLED (YES/NO) Enable/disable Bluetooth. See Section 6.10 for more information. • PAIRING MGMT Pair Bluetooth devices with the radio. See Section 6.10 for more information.

14221-1800-2000, Rev. F 42 5.10 ALERT TONES The radio provides audible Alert Tones or “beeps” to indicate various operating conditions. Some of the most common tones are described in Table 5-6. Table 5-6: Alert Tones TONE DESCRIPTION SOUND/DURATION Ready To Talk Tone Unencrypted (Analog FM or P25 digital) After a PTT is pressed, this is an audible indication (tone) for you to begin speaking into the microphone. 1000 Hz tone for 25 ms Ready to Talk Tone Encrypted P25 digital After a PTT is pressed, this is an audible indication (tone) for you to begin speaking into the microphone. 1200 Hz tone for 25 ms PTT Denied PTT not possible. Momentary tone is present: • Receive only • Key not found • PTT button disabled • Emergency button disabled • Emergency not supported for current channel • Clear transmit denied • Trunking Channel unavailable 544 Hz tone for 75 ms Maximum transmit duration expires Maximum transmit duration is exceeded. 5 beeps of 2400 Hz tone and then a 544 Hz tone for as long as PTT is pressed Low Battery Alarm Alarm sounds upon initial detection of low battery and every 30 seconds thereafter. Tone stops upon detection of a battery charging state. Sequence of tones: • 937 Hz tone for 50 ms • Silence for 60 ms • 1300 Hz tone for 50 ms Emergency Call Received Radio is receiving an emergency call or priority call. 600 Hz tone for 250 ms and 1800 Hz tone for 250 ms Out of Range Radio fails to find a local control channel. Programmable via RPM2: • Disabled (no tone) • Slow (tone every 15s) • Medium (tone every 10s) • Fast (tone every 5s) • Tones is 544 Hz tone for 75 ms

14221-1800-2000, Rev. F 43 5.11 SELECT ZONE/SYSTEM A System is a group of channels or talkgroups that share a common set of parameters as programmed using RPM2. For example, a Trunking system defines the parameters needed to communicate on a particular infrastructure by agency or geographical region, such as WACN, System ID, Talkgroups, etc. A conventional system defines the channel set used and any specific signaling attributes (See RPM2 for more information on System attributes). Systems are designated by the XX icon in the Zone/System menu. A Zone is an OPTIONAL container that can hold channels or talkgroups from a variety of systems (see Section 6.3.2). In other words, each member of a Zone belongs to an underlying system. (See RPM2 for more information on Zone attributes). Zones are always listed first in the Zone/System menu and are designated by the icon. A button on the radio can be programmed to scroll through available zones/systems (see Section 7.4). Or To select a zone/system via the menu: 1. Press the Menu/Select button to access the menus. 2. Use  or  to display the ZONE menu. The currently selected zone/system will be highlighted. A personality can have up to 512 systems and up to 50 Zones, independent of banks or channels. 3. Use  or  to highlight the desired zone/system. The  and  buttons may be held to scroll repetitively, and the menu will wrap to allow quick access to a particular zone/system, 4. Press the VIEW ZONE soft key to view channels in the zone/system, or Select the desired zone/system using the Menu/Select button.

14221-1800-2000, Rev. F 44 5.12 SELECT GROUP/CHANNEL AND BANK The radio can be programmed with 1,250 talkgroups or 1000 channels per personality. Use the Group/Channel knob to select groups/channels 1 - 16. Use the A/B/C/D switch to set the bank. The selected bank is indicated on the display. • Bank A: Channel A1 - A16 (1-16) • Bank B: Channel B1 - B16 (17-32) • Bank C: Channel C1 - C16 (33-48) • Bank D: Channel D1 - D16 (49-64) If your system has more than 64 groups/channels, a button on the radio can be programmed for the SEL CHAN/GRP option. This allows you to select a “super bank,” providing access to groups/channels beyond the first 64. Note that ZONES have a limit of 64 entries per zone and cannot be “superbanked.” Direct Channel Entry A button on the radio can be programmed for Direct Channel Entry, which allows the user to enter the talkgroup/channel number directly from the keypad. The radio can be programmed for one of the following Direct Channel Entry options: • When a Zone is selected on the radio, Direct Channel Entry performs a lookup using the currently selected system’s group list Or • When a Zone is selected on the radio, Direct Channel Entry performs a lookup using the currently selected Zone’s system/group list. 5.13 LOCK/UNLOCK KEYPAD There are two levels of keypad lock available. Keypad lock and Radio lock. Keypad lock only locks the navigation keys (except for use in unlock), programmable softkeys, and DTMF keypad. Radio lock disables all physical keys and knobs except: • The 4-position switch • PTT • Emergency Button • Any User Programmable Button (UPB) programmed for Monitor/Clear. (This is required to allow Monitor/Clear to function for 2-button emergency clear.) The A/B switch, ABCD switch, or a button on the radio can be programmed to lock the keypad/radio. If the keypad was locked via a switch, moving the switch to another position will unlock the keypad. If locked via a button, the navigation keys must be used to enter the unlock sequence of Left, Right, Up Down. See Section 7.4 for the various options that can be programmed to the radio buttons and switches. NOTE

14221-1800-2000, Rev. F 45 5.14 GROUP CALLS 5.14.1 Transmit a Group Call A talkgroup is a group of radios that you want to have private conversations with. These groups can be divided into areas such as state, region, county, or large special events. A group call can only be made on digital channels. Turn the Channel/Group knob to select the desired group (see Figure 5-1). Press PTT to transmit. Or A button on the radio can be programmed for DIRECT CHANNEL ENTRY to allow the user to enter the talkgroup/channel number. Press PTT to transmit. Or To transmit a group call: 1. In P25 Conventional, the talkgroup for the selected channel may be overridden as follows: Press the Menu/Select button to access the main menu. 2. Press  or  to display the CALL menu. 3. Press  or  to highlight CHANGE TLKGRP and press the Menu/Select button. 4. Press  or  to highlight and the desired talkgroup and press the Menu/Select button. After selecting the new talkgroup, the radio returns to the main screen. 5. Press the PTT button to transmit. 5.14.2 Receive a Group Call When receiving a group call, the status area of the idle display toggles between the Unit Name and the Group Name of the transmitting radio. Note that if either of those names is not programmed the corresponding ID number is displayed.

14221-1800-2000, Rev. F 46 5.15 INDIVIDUAL CALLS An individual call is used to make a call to one radio as opposed to a group of radios. An individual call can only be made on a digital channel. 5.15.1 Transmit an Individual Call 1. Press Menu/Select button to access the main menu. 2. Press  or  to display the CALL menu. 3. Press  or  to highlight INDIVIDUAL CALL and press the Menu/Select button. 4. Use  or  to highlight the unit to call and press the Menu/Select button, or select KEYPAD to enter the Unit ID. 5. Press PTT to make the call. When transmitting an Individual Call, the radio displays the called radio’s name or Unit ID. If the radio is programmed for Acknowledged Individual Call, the radio displays “CALL QUEUED” until the callee answers or rejects the call. 6. After the callee answers, press PTT to respond. 7. Press  to end the call. How long the radio remains in Individual Call mode with no activity is programmable. 5.15.2 Receiving an Individual Call 1. When receiving an Individual Call, the radio displays the calling radio’s name or Unit ID. The radio will also display “Press  to END.” 2. Press PTT to respond or  to END/REJECT the call. How long the radio remains in the Individual Call mode with no activity is programmable.

14221-1800-2000, Rev. F 49 5.17.2 Using Noise Cancellation When using the noise cancellation feature, observe the following: • Verify NOISE CANCELLATION is enabled (see Section 5.17.1). • Talk within two (2) inches of the primary microphone (see Figure 5-5). • Ensure the primary and secondary microphones are not covered. See Section 5.17.4 for more information on the primary and secondary microphones. • Speak clearly, loudly, and with authority. • In very noisy environments, it is o.k. to yell into the radio. The radio can handle loud input levels. Figure 5-5: Using Noise Cancellation 5.17.3 The Effect of Distance from the Microphone Unlike a normal microphone system, noise cancellation makes the level of your voice diminish quickly as you move away from the radio. In essence, the radio starts to see your voice as surrounding noise. Whereas, you may be comfortable speaking up to a foot away under normal operation, noise cancellation requires that you hold the radio close. 5.17.4 Primary versus Secondary Microphone 5.17.4.1 Without a Speaker Microphone Attached The primary microphone is located on top of the radio and the secondary is on the bottom of the radio (refer to Figure 5-1 for microphone locations). 5.17.4.2 With a Speaker Microphone Attached When a speaker microphone is attached, the radio electronically switches over to use the radio’s top left microphone as secondary. The microphone on the attached speaker microphone becomes primary. 5.17.5 When using an SCBA Mask When using an SCBA mask, the primary microphone can be held directly against the voice port. If the SCBA has a voice amplifier, the same rule applies. Ensure that the secondary microphone is uncovered. If possible, point the secondary microphone toward the noise source.

14221-1800-2000, Rev. F 50 5.18 PTT OPTIONS The radio can be programmed via RPM2 with one of the following PTT options: • Radio and Accessory - In this mode, when the radio is PTT’d the audio source will correspond with the PTT source.  If the source of PTT is radio, the audio is routed via the radio microphone.  If the source of PTT is an external microphone accessory, the audio is routed via the external microphone accessory. • Accessory Only - Any PTT input will have the audio routed through the external microphone accessory. The Bluetooth Speaker Mic is unaffected by this setting. PTTing the Bluetooth Speaker Mic always results in audio being routed via the Bluetooth Speaker Mic. 5.19 VOICE ANNUNCIATION When enabled via programming, Voice Annunciation provides audible feedback for various radio operations. The radio can be programmed to play an audio message for any or all of the following. This message can be a pre-recorded (canned) message or a user-recorded message. • Zone changes • Channel changes • System changes • Encryption On/Off • Noise Cancellation On/Off • Scan On/Off • Talkaround On/Off • Monitor Mode On/Off • 2 or 4 Position switch change For more information on configuring the radio for Voice Annunciation, refer to the Voice Annunciation Feature manual 14221-7200-6110. NOTE

14221-1800-2000, Rev. F 51 5.20 ENABLE/DISABLE ENCRYPTION A switch or a button on the radio can be programmed to enable/disable encryption. See Section 7.4 for the various options that can be programmed to the radio buttons and switches. Or Turn encryption on or off via the Security Menu: 1. Press the Menu/Select button to access the menus. 2. Use the  or  button to highlight and select the SECURITY menu. 3. Use the  or  button to highlight ENCRYPTION. Toggle encryption enabled/disabled using the Menu/Select button. This option is grayed out if any switch is programmed for encryption, or if Encryption Mode in the radio’s personality is programmed “Forced On.” • If a channel is programmed to be encrypted, an optional key icon appears on the main display when encryption is enabled. The system must also be programmed for encryption. • When encryption is enabled and you use any channel not configured for encryption, the radio allows PTT. The signal is transmitted unencrypted. • Systems configured for Global Encryption (enabled in the Security menu) can display an optional Global Encryption icon in addition to or instead of a key icon (Section 6.20.3). 5.21 TRANSMIT ENABLE/DISABLE When transmit is disabled, all forms of transmission from the radio are disabled, including Bluetooth. This is designed for use in explosive atmospheres. If enabled via programming, use the A/B switch to enable or disable transmit. See Section 7.4 for the various options that can be programmed to the radio buttons and switches. NOTENOTE

14221-1800-2000, Rev. F 52 5.22 CHANNEL GUARD (ANALOG CONVENTIONAL ONLY) Channel Guard is Harris’s trademark for CTCSS (tone squelch) and CDCSS (digital tone squelch). The Channel Guard menu is only accessible if the System is setup for CG SEL in the radio’s personality. To select the Channel Guard tone: 1. Press Menu/Select button to access the main menu. 2. Use  or  to display the CALL menu. 3. Use  or  to highlight CHANNEL GUARD and press the Menu/Select button. 4. Use  or  to highlight RECEIVE GUARD or TRANSMIT GUARD and press the Menu/Select button. 5. Use  or  to highlight the desired option from the list and select using the Menu/Select button. 6. The Channel Guard frequency is displayed on the main display. The Channel Info screen and Channel Edit screen will change depending on this selection. See Sections 6.4 and 7.2 for more information. A button on the radio can be programmed for Channel Guard Override (see Section 7.4). NOTENOTE

14221-1800-2000, Rev. F 53 5.23 USE TALKAROUND TO BYPASS REPEATER (ANALOG AND P25 CONVENTIONAL ONLY) You can bypass the repeater system to communicate directly with other radios on your current channel’s receive frequency. This is useful if you are out of range of a repeater or if a repeater is busy. You will need to be in range of the other radio. In XLP R4A and later, talkaround can be enabled/disabled on a per-channel basis. To enable talkaround: 1. Press Menu/Select button to access the main menu. 2. Press  or  to display the CALL menu. 3. Press  or  to highlight TALKAROUND MODE. 4. Press the Menu/Select button to toggle TALKAROUND MODE to ENABLED. 5. The optional Talkaround icon appears. Calls are now made on the receive frequency until you disable talkaround mode via the CALL menu. Power cycling the radio does not disable talkaround. Or A button or switch can be programmed to toggle talkaround enable/disabled. See Section 7.4 for the various options that can be programmed to the radio buttons and switches. If the Talk-Around Indication feature is enabled using RPM2, the radio will play a unique grant tone when a call is placed on a simplex channel or when Talk-Around has been enabled on a duplex channel. This feature applies to both Analog and P25 Conventional systems. It optionally allows the radio to also play the same tone when it receives a call while operating in simplex or Talk-Around. If configured, the radio plays the tone at the selected volume level. NOTE

14221-1800-2000, Rev. F 54 The tone will not play on systems configured with MDC. Talk-Around Indication can be specified for each individual Analog and P25 Conventional system configured in personality. The following options can be selected, and apply only when the radio is on a simplex channel or when Talk-Around has been enabled by the user: • Disabled: (This is the default option.) When this option is selected, the radio plays the standard grant tone when a call is placed. The radio does not play a tone when a call is received. • Transmit Only: When this option is selected, the radio plays a different “Talk-Around” grant tone when a call is placed. The radio does not play a tone when a call is received. • Transmit & Receive: When this option is selected, the radio plays a different “Talk-Around” grant tone when a call is placed, and at the beginning of a received call. In the radio personality, the “Alert Tone” parameter needs to be enabled for each channel on the Conventional Frequency Set. The “Ready To Talk Tone” parameter must also be enabled for the Talk Around Indication tone to be played when the radio is keyed. 5.24 TYPE 99 OPERATION Type 99 is Harris' name for in-band, two-tone sequential signaling. It is a conventional signaling protocol used to control the muting and unmuting of a radio. This signaling is commonly used for selective calling of individual units or groups of units in a conventional system. In Type 99 tone systems, calls are not heard until the radio detects the proper two-tone sequence. This, in conjunction with squelch, prevents the user from hearing noise or undesired conversations. When the radio detects the second tone, it sounds the appropriate Type 99 alert tone. After the second tone stops, the receiver audio path is opened in order for the user to receive messages. 5.24.1 Enable/Disable Type 99 To enable Type 99: 1. Press Menu/Select button to access the main menu. 2. Press  or  to display the CALL menu. 3. Press  or  to highlight T99 TOGGLE. 4. Press the Menu/Select button to change T99 TOGGLE between ENABLED and DISABLED. T99 is displayed in the top of the radio display when Type 99 is enabled. Or A button or switch can be programmed to enable/disable Type 99 (see Section 7.4). NOTENOTE

14221-1800-2000, Rev. F 55 5.24.2 Disable After PTT If this option is programmed using RPM2, Type 99 is disabled after the radio user activates the PTT. This allows the radio user to monitor traffic on the channel (after a PTT action) without pressing the monitor button. Can be used in conjunction with the “Auto Reset” option (see Section 5.24.3) to disable Type 99 after a PTT and automatically reset, or enable, Type 99 after 30 seconds. 5.24.3 Auto Reset If this option is programmed using RPM2, Type 99 is automatically reset, or turned back on, after 30 seconds. Can be used in conjunction with the “Disable After PTT” option (see Section 5.24.2) to disable Type 99 after a PTT and automatically reset, or enable, Type 99 after 30 seconds. 5.25 CALL ALERT (PAGE) 5.25.1 Send Alert To send an alert: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the CALL menu. 3. Press  or  to highlight CALL ALERT and press the Menu/Select button. 4. Press  or  to highlight the desired unit from the list and press the Menu/Select button, or select KEYPAD to enter the Unit ID. 5. Press PTT to send the page. 5.25.2 Receive Alert 1. When receiving a Call Alert, the radio displays the calling radio’s name or Unit ID. 2. The radio rings and indicates a missed call. The ring sounds continuously until you press PTT, press the CLR MISSED softkey, change group/system, or power cycle the radio. 5.26 DTMF The XL-Portable supports the transmission of DTMF tones corresponding to the numbers/characters on the keypad. To overdial numbers/characters, press and hold the PTT button, and then press the corresponding keys one at a time on the keypad. Valid keys for DTMF tones are: 1, 2, 3, 4, 5, 6, 7, 8, 9, *, 0, and #.

14221-1800-2000, Rev. F 56 For conventional or P25 Conventional systems, DTMF tones only play if the current system is programmed for DTMF (part of general System configuration). DTMF tones are always enabled for P25 Trunking systems. 5.27 AUDIO PLAYBACK The Audio Playback feature allows the user to playback a previously received call. Recordings are stored in the radio’s RAM and are not persistent across power cycles. The radio stores the last five (5) recorded calls up to 1 minute each. A button on the radio can be programmed to replay the last recorded call. To playback the last received call from a button: 1. Press the button programmed for audio playback. The last call received before the button was pressed is played each time the button is pressed. 2. Additional incoming calls will be recorded in the background, but pressing the button continues to replay the captured call until reset. 3. To reset the feature and allow a new call to be captured, press and hold the button until you hear a 2-tone chirp. At this point the button can be used to capture an new incoming call. You can also playback one of the last five calls received via the menu. To playback a previously received call from the menu: 1. Press the Menu/Select button. 2. Press  or  to display the CALL menu. 3. Press  or  to highlight AUDIO PLAYBACK and press the Menu/Select button. 4. Select the desired call from the list (the most recent call is at the top of the list) and press the select button. The selected call will be played. • If a button is also programmed for Audio Playback, pressing the button replays the call that selected in the menu. The feature must be reset as above in order to use the button to capture a new call. • If a button is not programmed for Audio Playback, then you must navigate back to the menu to play the call again. Any incoming call that occurs during playback preempts the playback. NOTENOTE

14221-1800-2000, Rev. F 57 5.28 START SCAN This procedure assumes that the scan list has been added and the radio is not in active scan. Refer to Section 6.13 for scan setup or Section 5.29 for stopping scan. Refer to Section 6.14.1.1, Section 6.14.1.2, and Section 6.14.1.3 for home and priority channel descriptions. To start scan: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the SCAN menu. 3. Press  or  to highlight START SCAN and press the Menu/Select button. START SCAN text changes to STOP SCAN. 4. Press the BACK soft key to exit the scan menu. 5. The scan icon is displayed on the idle display when scanning is enabled. Or To start scan: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the SCAN menu. 3. Press  or  to highlight SCAN LISTS and press the Menu/Select button. 4. Press  or  to highlight the desired SCAN LIST and press the START SCAN soft key. Or A switch or button on the radio can be programmed to start/stop scan.

14221-1800-2000, Rev. F 58 If a switch is programmed for start/stop scan, the menu for starting and stopping scan is disabled. See Section 7.4 for the various options that can be programmed to the radio buttons and switches. 5.29 STOP SCAN 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the SCAN menu. 3. Press  or  to highlight STOP SCAN and press the Menu/Select button. 4. Press the BACK soft key to exit the scan menu. Or 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the SCAN menu. 3. Press  or  to highlight SCAN LISTS and press the Menu/Select button. 4. Press the STOP SCAN soft key. Or A switch or button on the radio can be programmed to start/stop scan. If a switch or button is programmed for start/stop scan, the menu for starting and stopping scan are disabled. NOTENOTENOTE

14221-1800-2000, Rev. F 59 See Section 7.4 for the various options that can be programmed to the radio buttons and switches. 5.30 MONITOR AND SQUELCH TYPES (CONVENTIONAL ONLY) The monitor function allows you to temporarily turn off selected squelch to monitor for traffic that may not normally break squelch. The type of squelch used depends on an analog or digital channel. A button or switch on the radio can be programmed to start or stop Monitor (see Section 7.4 for the various options that can be programmed to the radio buttons and switches.). For analog channels, there is: • Noise squelch - any received signal breaks squelch. • Continuous Tone Coded Squelch (CTCSS) - squelch is selective based on tone code. • Continuous Digital Coded Squelch (CDCSS) - squelch is selective based on digital code. For digital channels, there is: • Monitor squelch - any received digital signal breaks squelch. • Normal squelch - Received Network Access Code (NAC) must be correct to break squelch. • Selective squelch - Received NAC and talkgroup Identification (ID) or unit ID must be correct to break squelch. During encrypted operations, the radio only unmutes when receiving with the same key. NOTENOTE

14221-1800-2000, Rev. F 60 5.31 NUISANCE DELETE A channel can temporarily be deleted from the scan list. The selected channel, priority 1, and priority 2 channels cannot be nuisance deleted. A button or switch on the radio can be programmed for nuisance delete (see Section 7.4 for the various options that can be programmed to the radio buttons and switches). Nuisance delete can only be performed on the active scan list. To perform nuisance delete from the menu: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the SCAN menu. 3. Press  or  to highlight SCAN LISTS and press the Menu/Select button. 4. Press  or  to highlight the scan list and press the Menu/Select button. When scanning is started, indicates the active scan list; when scanning is stopped, indicates the active scan list. 5. Press  or  to highlight the desired channel. 6. Press the OPTIONS soft key. 7. Press  or  to highlight NUISANCE and press the Menu/Select button. 8. The icon appears next to the channel and it will not be scanned. NOTE

14221-1800-2000, Rev. F 61 9. Highlight the channel, press the OPTIONS soft key, and select ADD BACK to add channel back to scan list. If you do not add the channel back to the list, the channel will return to the scan list when you cycle radio power or activate a personality. 10. Press the BACK soft key to exit the channel list. 11. Press the BACK soft key to exit the scan list display. 5.32 CONVENTIONAL FAILSOFT (EDACS ONLY) In the unlikely event of an EDACS system failure, communications can take place in Conventional Failsoft mode. The radio is automatically directed to a communications channel set up for this purpose. An increase in activity on the channel during Conventional Failsoft operation may be noticed, so be careful not to transmit until the channel is clear. Operation during Conventional Failsoft is the same as operation on a conventional system, except that it is not possible to select a communications channel, or use emergency and special call. When trunking is restored, the radio automatically returns to normal operation. Emergency and special calls are not operational during Conventional Failsoft. NOTE

14221-1800-2000, Rev. F 62 5.33 EMERGENCY OPERATION The radio can be programmed to enable emergency mode. Unit name displays on dispatcher console if an emergency signal is received from another radio on a digital channel. 5.33.1 Declaring an Emergency Call To declare an emergency: 1. Press and hold the emergency button on the radio or the speaker microphone. The length of time you need to hold the button is configured using RPM2. 2. The emergency icon is displayed on the idle display. • For digital channels, the radio transmits the talkgroup or radio ID to the dispatch console and receiving radio. • The radio can be programmed to have a dedicated emergency channel, which can be activated from analog or digital channels. • The radio can also be programmed to send an Emergency Alarm in addition to or in place of the emergency call (P25 modes). • If enabled via programming, the declaring radio sounds a recurring tone until the battery drains or the radio is powered off. Alert tone continues to play even after clearing the emergency. This tone stops during PTT and resumes when PTT is released. This tone is played at max volume and cannot be controlled with the volume knob. The radio goes through transmit and receive cycles if so configured. Speak into the microphone while the radio is transmitting or press PTT to talk. 3. To exit emergency, power cycle the radio or select EXIT EMERGENCY from the CALL menu. If enabled via programming, you can clear an emergency by pressing the button programmed for the Monitor/Clear function and then the emergency button. 5.33.2 Receiving an Emergency Call When receiving an Emergency Call, an alert beep sounds (if tones are enabled) and an emergency indication is displayed. The unit ID and/or unit name of the unit in emergency is displayed. While the emergency display is active, press PTT to respond to the emergency caller.

14221-1800-2000, Rev. F 63 5.33.3 Stealth Emergency The radio can be programmed with the following emergency behavior: • No audio indications when declaring an emergency. Or • No visual indications when declaring an emergency. Or • No audio and no visual indications when declaring an emergency. During stealth mode, the radio will not receive any type of call. Once the user presses the PTT button, the radio display and audio return to normal. 5.34 MDC-1200 (ANALOG CONVENTIONAL ONLY) MDC-1200 is a legacy in-band signaling protocol that provides the radio with the ability to transmit and receive a unique PTT ID. This PTT ID can be decoded by receiving radios and displayed as a hexadecimal number or an alias string. In addition, MDC-1200 provides radios with the ability to transmit emergency status to a console. Refer to the MDC-1200 Feature Manual, 14221-7200-6000, for complete instructions on configuring and using this feature. 5.34.1 Normal PTT Operation If MDC signaling on PTT press is enabled using RPM2, the radio transmits an MDC PTT ID message when PTT is pressed. If the Sidetone option is enabled using RPM2, the radio plays a Ready-to-Talk (RTT) tone after the MDC pre-signaling has been transmitted. If MDC signaling on PTT release is enabled (using RPM2), the radio transmits post-call MDC signaling when PTT is released. • IF STE is enabled (using RPM2), the MDC post-call signaling is transmitted after STE is sent on PTT release only. • MDC post-call signaling is also sent when there is a radio unkey due to Carrier Control Timeout (CCT). Normal CCT alert tones occur prior to unkey. 5.34.2 MDC PTT ID Receive Handling When the radio receives an MDC PTT ID, it searches the MDC ID Alias List for an alias associated with the ID. If one is found, it displays the alias. If none is found, the radio displays the ID in hexadecimal. 5.34.3 Emergency Declaration Emergency declaration is accomplished by the radio generating an MDC Emergency PTT message. An Emergency is considered acknowledged when the radio receives an “Ack To Emergency” PTT message with an ID which matches its own ID. If Emergency Audio is enabled and the PTT Sidetone option is enabled, the radio plays the Ready-to-Talk tone after the MDC Emergency PTT signaling is transmitted. • If an MDC Alert on ACK is enabled, the radio plays an ACK tone when the MDC emergency is acknowledged. • If audio tones are enabled, the radio plays an ACK tone if the emergency is not acknowledged within the programmed number of retries.

14221-1800-2000, Rev. F 64 5.35 BEON OPERATION The BeOn solution is a Voice over IP (VoIP) based, Push-to-Talk (PTT) communications system operating over public or private wireless networks. The solution extends traditional Land Mobile Radio (LMR) services onto the broadband capable third generation (3G) and 4G/LTE cellular networks. This includes the ability to provide highly integrated interoperability services between BeOn users on the cellular network and users of traditional LMR networks. Harris’ VIDA® IP core network switching technology is the foundation for the BeOn application infrastructure. As a result, the application and product suite provide many advanced features not found in competing technologies, and provide internetworking of those services between public and private communications networks. The XL-Portable supports BeOn operation on Wi-Fi or LTE. It may be necessary to consult one or more of the following when configuring and using BeOn: • BeOn Configuration and Use Feature Manual: 14221-7200-6130 • BeOn LAS/LAP Installation and Configuration Manual: 14221-710-3010 • Unified Administration System User’s Manual: MM24374 • RPM2 online help NOTE

14221-1800-2000, Rev. F 65 6. ADVANCED OPERATIONS 6.1 VIEW/CHANGE PERSONALITIES Personalities contain radio programming information such as frequencies, channels, stations, and talk groups. Up to 10 different personalities can be stored in the radio, but only one can be activated at a time. 6.1.1 View Personalities 1. At main display, press the Menu/Select button to access the main menu. 2. Press  or  to display the UTILITY menu. 3. Press  or  to highlight PROGRAM and press the Menu/Select button. An arrow indicates the currently active personality. 4. Press the OPTIONS soft key. 5. Select VIEW PLAN INFO to view. 6. The radio displays the plan’s filename. Personality information appears if the field was filled out using RPM2.

14221-1800-2000, Rev. F 66 6.1.2 Change Active Personality To change the active personality: 1. At main display, press the Menu/Select button to access the main menu. 2. Press  or  to display the UTILITY menu. 3. Press  or  to highlight PROGRAM and press the Menu/Select button. 4. Press  or  to highlight the desired personality and press the Menu/Select button. indicates the currently active personality. 5. Press the YES soft key to confirm personality activation. If the personality has a power-up PIN, you are prompted to enter the PIN before activation continues. 6. The IN PROGRESS screen is displayed while plan activation is in progress. 7. If personality is activated, the radio displays PLAN COMPLETE followed by the name of the personality. Press the OK soft key. • You cannot activate a personality when the radio is transmitting an emergency. • A FAILED message may be displayed for errors such as invalid syntax in the fill or some other invalid parameter.

14221-1800-2000, Rev. F 67 6.2 SITUATIONAL AWARENESS (SA) – P25 CONVENTIONAL ONLY Situational Awareness is a feature in which the radio receives SA position from other units configured to send the SA packets. The SA display shows the positions of the other radios (units) relative to the radio. To make use of SA, all radios need to have a uniquely programmed Unit ID. To display Situational Awareness Info: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the UTILITY menu. 3. Press  or  to select GPS and press the Menu/Select button. 4. Press  or  to select POSITION INFO and press the Menu/Select button. 5. Press the NEXT soft key. 6. Press  or  to view the location of each unit. The color of each unit indicates its status as follows. Only one status can be shown at a time and are listed in priority order: • Grey – Unselected, no status • Red – Unselected, In Emergency • Orange – Unselected, Low Battery • Blue - Unselected, Scanning • Green – Selected, no status • Green/Red – Selected, In Emergency • Green/Orange – Selected, Low Battery • Green/Blue – Selected, Scanning 7. GPS of this radio is shown by the center dot as follows: • Green – Tracking • Orange – Last known position • Red – Searching 8. Press  or  to zoom the display distance of current unit.

14221-1800-2000, Rev. F 68 9. Press the OPTIONS soft key. From here, select UNIT INFO to display details about the selected unit, select REFRESH to update information, or select EXIT. 6.3 USER-DEFINED ZONES/SYSTEMS 6.3.1 Command Tactical Zone A Command Tactical Zone is defined at the radio. A Command Tactical Zone is reset when a Personality is activated. To create a Command Tactical Zone: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the ZONE menu. 3. Press  or  to highlight <USER-DEFINED> and press the VIEW ZONE soft key. 4. Press the OPTIONS soft key. 5. Press  or  to select EDIT ZONE to create a zone, or RENAME ZONE to rename the Command Tactical Zone (up to 16 characters are allowed). 6. Press  or  to scroll through existing systems. Press  or  to highlight desired channel/group. 7. Press the Menu/Select button to add or remove channel/group. 8. After adding all desired channels/groups, press the BACK soft key. NOTE

14221-1800-2000, Rev. F 69 9. Activate the Command Tactical Zone by selecting the SET ACTIVE soft key on the USER DEFINED screen, or by pressing the Menu/Select button when <USER DEFINED> is highlighted on the Zone menu. 10. After a creating a Command Tactical Zone, select OPTIONS to edit the Command Tactical Zone, delete channels/groups, clear the zone, and rename the zone. 6.3.2 Mixed System Zone Mixed System Zones are defined using RPM2 and cannot be edited on the radio. If a Mixed System Zone is not configured using RPM2, it will not appear on the radio. Up to 50 Mixed System Zones can be defined. You can view details about each channel/group. A user programmable button can be defined to scroll through just the mixed system zones. To view Mixed System Zones: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the ZONE menu. 3. Press  or  to highlight the desired zone (Note: Zones are indicated by the icon) and select VIEW ZONE to view the groups/channels in the zone list.

14221-1800-2000, Rev. F 70 6.4 CH INFO MENU The Channel Information (CH INFO) menu displays information about the currently selected channel. The information displayed varies between conventional and trunked systems. To display channel information: 1. Press  while on the idle display. 2. Press  or  to scroll through the programmed channel settings. CONVENTIONAL OR P25 CHANNELS ONLY: 3. Press the EDIT soft key. 4. Enter the password. You may now select and change the values of the displayed channel parameters. The password remains active until power cycle. Refer to Section 7.2 for more information. 6.5 AUDIO SETTINGS From this menu, you can set audio settings such as speaker mute, noise cancellation, PTT, and tones. 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the UTILITY menu. 3. Press  or  highlight AUDIO SETTINGS and press the Menu/Select button. 4. Press  or  to scroll through available audio settings. Press the Select/Menu button to change settings as desired: • SPEAKER - Mute or Unmute the speaker audio. • NOISE CANCELLATION - Enable or disable noise cancellation. Noise cancellation reduces background noise during transmit. • PTT - Enable or disable Push-To-Talk (PTT). Disable PTT to prevent accidental keying, such as when the radio is in a holster or you are getting into a car. • TONES - Enable or disable alert tones (see Table 5-6).

14221-1800-2000, Rev. F 71 • KEYPAD TONES - Enable or disable keypad tones. When enabled, the radio plays a tone when a button on the keypad is pressed. 5. Press the BACK soft key to exit menu. 6.6 DISPLAY SETTINGS To change display settings: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the UTILITY Menu. 3. Press  or  to highlight DISPLAY SETTINGS and press the Menu/Select button. 4. Press  or  and the Select/Menu button to change settings as desired: • COLOR SCHEME - Change the color scheme of the top and front displays for optimum viewing in day/night conditions. • FRONT BACKLIGHT - Turn front display backlight on, off, momentary, or momentary (off). Momentary (off) is similar to momentary, but the backlight turns off completely and only comes on when the center navigation button is pressed. • FRONT BRIGHTNESS - Set brightness level of front display. A level of 0 has same effect as turning off backlight. • FRONT TIMEOUT - Specify how long the radio needs to be inactive before the front display’s backlight turns off. • TOP BACKLIGHT - Specify how long the top display’s backlight will remain lit: MOMENTARY, ON, or OFF. • TOP BRIGHTNESS - Set the brightness level of the top display. A level of 0 turns off top display and indicator (TX/RX) LED. • TOP TIMEOUT - Specify how long the radio needs to be inactive before the top display’s backlight turns off. • TOP ORIENTATION - Set orientation of top display to be viewed from radio: FRONT, BACK, or AUTO. When AUTO is selected, the radio changes the top display to be viewed from back if an external microphone or speaker is attached. Otherwise, the display can be viewed from the front. • INDICATOR LED - Toggle the indicator LED ON/OFF. 5. Press the BACK soft key to exit the menu.

14221-1800-2000, Rev. F 72 6.7 GPS SETTINGS The GPS SETTINGS menu item only appears if enabled using RPM2 and the feature is installed. To access GPS settings: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the UTILITY menu. 3. Press  or  to highlight GPS and press the Menu/Select button. 4. Use  or  and the Select/Menu button to change settings as desired: • GPS - Enable or disable internal GPS. • POSITION INFO - See Section 6.8. • LINEAR UNITS - Set unit of measurement of displayed linear units: STATUTE, METRIC, or NAUTICAL. • ANGULAR UNITS - Set unit of measurement of displayed angular units: CARDINAL, DEGREES, or MILS. • POSITION FORMAT- Set format of displayed position information: Latitude/Longitude Degrees Minutes Seconds (LAT/LONG DMS), LAT/LONG DM, Military Grid Reference System (MGRS), or Universal Transverse Mercator (UTM). 5. Press the BACK soft key to exit the menu. 6.8 POSITION INFO The Position Info screen displays the radio user’s location information. GPS must be enabled in the GPS Settings (see Section 6.7). To display position info: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the UTILITY menu. 3. Press  or  to highlight POSITION INFO and press the Menu/Select button. NOTE

14221-1800-2000, Rev. F 73 4. Press  or  to scroll through available location information. 6.9 WI-FI The XL-Portable supports programming via Wi-Fi. Refer to Appendix A for information on configuring Wi-Fi. To enable Wi-Fi programming mode on the radio: 1. Ensure the radio is powered off. 2. Press and hold the bottom side button and PTT button (see Figure 4-1). Figure 6-1: Enabling Wi-Fi 3. Power on the radio. 4. The WIFI INSTALL ACTIVE screen is displayed (Figure 6-2). The radio displays DISCONNECTED if not connected to a wireless network, or CONNECTED if connected to a wireless network.

14221-1800-2000, Rev. F 74 Figure 6-2: Wi-Fi Install Active 6.10 BLUETOOTH The BLUETOOTH menu item only appears if enabled using RPM2 and if the feature is installed. 6.10.1 Enable Bluetooth To enable Bluetooth: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the UTILITY menu. 3. Press  or  to highlight BLUETOOTH and press the Menu/Select button. 4. Press  or  to highlight ENABLED and press the Menu/Select button to toggle YES/NO. NOTE

14221-1800-2000, Rev. F 75 6.10.2 Pair Devices To pair devices: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the UTILITY menu. 3. Press  or  to highlight BLUETOOTH and press the Menu/Select button. 4. Press  or  to highlight PAIRING MGMT and press the Menu/Select button. 5. Make sure device being paired is powered on and has discovery mode enabled in order to pair with the radio. If no devices are found and Bluetooth is enabled, only the ADD NEW soft key is available. If devices are paired, the OPTIONS soft key appears. 6. Press the ADD NEW soft key to select a device to pair. 7. A list of available Bluetooth devices appears. 8. Press the REFRESH soft key to refresh the device list if the desired device does not appear. 9. Press  or  highlight the desired device and press the PAIR softkey. 10. Pairing progress is displayed. • For Bluetooth 2.0 devices, a pin code screen appears. Enter the pin code and select OK. • For Bluetooth 2.1 devices, a PASSKEY accept/deny screen appears. Select ACCEPT. Accept the passkey on the Bluetooth 2.1 device as well.

14221-1800-2000, Rev. F 76 11. A PAIRING COMPLETE message appears when pairing is complete. Select OK. The paired device is then displayed in the PAIRED DEVICES list. 6.11 CLOCK SETTINGS To view/change clock settings: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the UTILITY menu. 3. Press  or  to highlight CLOCK SETTINGS and press the Menu/Select button. 4. Use  or  and Menu/Select button to change settings as desired: • TIME FORMAT- Set 12 or 24 hour time display format. • TIME ZONE - Set time zone relative to Universal Time Coordinated (UTC). 5. Press the BACK soft key to exit. 6.12 BATTERY INFO To display battery information: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the UTILITY menu. 3. Press  or  to highlight MAINTENANCE and press the Menu/Select button. 4. Press  or  to highlight BATTERY INFO and press the Menu/Select button.

14221-1800-2000, Rev. F 77 5. Battery information is displayed (state, voltage, capacity, and chemistry). Use only Harris approved batteries. Injury could occur from using incorrect battery. 6.13 SELECT LANGUAGE To change the language displayed by the radio: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the UTILITY menu. 3. Press  or  to highlight CHANGE LANGUAGE and press the Menu/Select button. 4. Press  or  to highlight the desired language and press the Menu/Select button. 6.14 SET UP SCAN These procedures are used to set up the scan list, home channels, and priority channels. To access the scan lists: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the SCAN menu. 3. Press  or  to highlight SCAN LISTS and press the Menu/Select button. Refer to the following sections. WARNING

14221-1800-2000, Rev. F 78 When using Preemptive Priority Scan, the frequencies in the list need to be unique. 6.14.1 Default, Priority 1, and Priority 2 Channels 6.14.1.1 Default Channel This is the currently selected channel and is the channel you transmit on by default when you press PTT while the radio is actively scanning and is not responding to a just received call. Responding to a call the radio just received while scanning is called hang time. If hang time is set to 0 using RPM2, the radio always transmits on the default channel in scan. 6.14.1.2 Priority 1 Channel This channel will be scanned more often than other channels in the list and will be scanned in between every other channel in the scan list. An example scan sequence would be P1 (priority 1), C2, P1, C3, P1, C4, etc. In addition, the priority channel will be scanned even while actively receiving on a non-priority channel. For example, if the radio is actively receiving on C3 and activity is detected on P1, the radio will drop C3 and switch to P1. 6.14.1.3 Priority 2 Channel This channel will also be scanned more often than others. An example scan sequence would be P1, C2, P1, C3, P1, C4, P2, C5, P1, C6, P1, C7, P1, C8, P2, C9 etc. In addition, this channel will be scanned even while actively receiving on a non-priority channel. For example, if the radio is actively receiving on C3 and activity is detected on P2, the radio will drop C3 and switch to P2. Additionally, activity on P1 can also preempt P2, but P2 cannot preempt P1. 6.14.2 Trunked/Conventional Scanning Trunked/conventional scanning adds the ability to scan multiple conventional and P25 conventional channels while still maintaining trunked radio operation. In essence, the radio is able to scan a conventional scan list while still receiving a trunked control channel and receiving trunked calls. Selection of which conventional scan list is associated with a given trunked system is done using RPM2 and cannot be changed on the radio. However, a user with access to the necessary menu layout (see Section 5.8) is allowed to edit the scan list members (both trunked groups and conventional channels on the selected Conventional Priority System). As the number of conventional channels being scanned increases, the time between scanning each channel increases (roughly 250 milliseconds per channel), with the consequent increase in the number of calls that will late-enter. In order to avoid missing calls, it is recommended to keep the number of conventional channels being scanned to eight (8) or fewer. The trunking site must have roaming set to Enhanced CC. NOTENOTE

14221-1800-2000, Rev. F 79 6.14.3 Vote Scan (Analog and P25 Conventional Only) If vote scan is enabled via RPM2, the radio automatically selects the strongest signal ensuring that the best audio quality is delivered to the user. If vote scan is enabled, the radio is always scanning. You cannot stop scanning, start normal scanning, or monitor the channel. The scanning icon on the idle screen indicates that the radio is vote scanning versus, regular scanning. If Talkaround is enabled, Vote Scan is disabled until Talkaround is disabled again. 6.14.4 Edit Scan List Depending on the scan list options selected via RPM2, you may be able to add or remove channels/groups from the scan list. To edit the scan list: 1. Press the Menu/Select button. 2. Press  or  to display the SCAN menu. 3. Press  or  to select SCAN LISTS. 4. Press  or  to highlight the scan list and press the Menu/Select button. 5. Press  or  to highlight channel/group. 6. Select OPTIONS. 7. Press  or  to select ADD CHAN/DELETE CHAN, SET PRI1, SET PRI2, REMOVE PRI, or NUISANCE/ADD BACK. NOTE

14221-1800-2000, Rev. F 80 When a channel is not grayed out in the list, DELETE CHAN appears. When a channel/group is grayed out (not in list), ADD CHAN appears. 8. Press the Menu/Select button to toggle selection. 6.14.5 Set or Remove Priority 1 and Priority 2 Channels Priority channels are scanned more often than non-priority channels. Note that P1 and P2 can only be set if configured as “Keypad” and the scan list is not set to “Fixed” using RPM2. To set or remove priority 1 and priority 2 channels: 1. Press the Menu/Select button. 2. Press  or  to display the SCAN menu. 3. Press  or  to highlight SCAN LISTS and press the Menu/Select button. 4. Press  or  to highlight the desired scan list and press the Menu/Select button. 5. Press  or  to highlight the desired channel/group. 6. Select OPTIONS. 7. Press  or  to highlight SET PRI1 or SET PRI2 and press the Menu/Select button. A Priority 1 channel appears with a P1 and a Priority 2 channel appears with a P2. 8. Select REMOVE PRI to remove priority.

14221-1800-2000, Rev. F 81 6.14.6 Custom Scan Lists The Mixed Zone Scan (MZS) feature gives the user the capability to scan based on a custom scan list that is assigned at the system level. The Custom Scan (CS) list can contain System and Channel/Group configurations across P25 Trunked, P25 Conventional, and Analog Systems. When a Custom Scan List is assigned to a P25T system, the radio can scan P25T, P25C and Analog systems. When assigned to a P25C or Analog system, the radio only scans conventional channels. MZS also gives the user the capability to scan beyond the selected system group set. • P25T Scan When a custom scan list is assigned to a P25T system, the user has the ability to scan P25T, P25C, and Analog groups/channels. All P25T systems must have the same WACN, System ID, and Unit ID to be added to the custom scan list. If P25C and/or analog channels are added to the custom scan list, the radio will scan them using the Trunked/Conventional scan feature described in section 6.14.2, and will override any other conventional scan list that may have been programmed using RPM2. • P25C and Analog Scan When a custom scan lists is assigned to a P25C or Analog System, the user has the ability to scan P25C and Analog channels. P25T systems are ignored. Custom scan list can be created using RPM or at the radio. The radio supports up to 10 Custom Scan lists, with up to 100 channels/groups in each.

14221-1800-2000, Rev. F 82 6.14.6.1 Create Custom Scan List To create a custom scan list at the radio: 1. Press the Menu/Select button. 2. Press  or  to display the SCAN menu. 3. Press  or  to highlight ASSIGNED CUSTOM LIST and press the Menu/Select button. 4. Press the OPTIONS softkey. 5. Select ADD SCAN LIST. 6. Press  or  to highlight the newly added scan list and press the VIEW/EDIT soft key. 7. Press  or  to display the desired system. 8. Press  or  to highlight the desired group/channel and press the OPTIONS softkey. From here, you can add/delete channels from the scan list, and set/remove Priority 1 and Priority 2 channels.

14221-1800-2000, Rev. F 83 When a custom scan list is selected, that list is scanned any time scanning is enabled for any Trunked, conventional, or P25 Conventional system. To scan only the channels assigned to a particular system, custom scanning must be turned off. 6.14.7 Wide Area System Scan (P25 Trunked and EDACS) Wide Area System Scan (WASCAN) causes the radio to roam across mobile systems when the currently selected system's control channel is lost. The radio will scan the control channels of other systems. To enable/disable Wide Area System Scan: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the SCAN menu. 3. Press  or  to highlight SITE ROAMING and press the Menu/Select button to toggle Wide Area System Scan ENABLED/DISABLED. 4. Select BACK to exit the scan menu. 6.15 RADIO STATUS The status feature allows the radio user to send a particular status condition to the site without making a voice call. There can be up to 10 status conditions programmed into the radio. For each status defined, there is an ID and an alphanumeric name. The ID is sent to the site and the alphanumeric name appears on the radio display when the ID corresponds with the information programmed at the site. A button on the radio can be programmed to send a radio status (see Section 7.4). To send a radio status: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the MESSAGES menu. 3. Press  or  to highlight RADIO STATUS and press the Menu/Select button. 4. Use  or  and the Menu/Select button to highlight and select desired status. NOTENOTE

14221-1800-2000, Rev. F 84 6.16 RADIO MESSAGE The message feature is used to send a particular message to the site without making a voice call. There can be up to 10 messages programmed into the radio. For each message defined, there is an ID and an alphanumeric name. The ID is sent to the site and the alphanumeric name appears on the radio display when the ID corresponds with the information programmed at the site. A button on the radio can be programmed to send a radio message (see Section 7.4). To send a radio message: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the MESSAGES menu. 3. Press  or  to highlight RADIO MESSAGE and press the Menu/Select button. 4. Use  or  and the Menu/Select button to highlight and select the desired message. 6.17 RADIO TEXTLINK Radio TextLink provides short text messaging functionality for radios. Due to the difficulty of entering text messages on a radio, predefined "canned" messages and predefined replies can be stored in the radio. To facilitate sending messages where information must be provided at send time, text message forms can also be stored in the radio. A form can contain up to four (4) text prompts, for which the operator enters alphanumeric values before sending the message. NOTE

14221-1800-2000, Rev. F 85 6.17.1 Radio TextLink Messages To send a canned Radio TextLink message: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the MESSAGES menu. 3. Press  or  to highlight TEXTLINK MESSAGES and press the Menu/Select button. 4. Press  or  to display the desired message. • Press the Menu/Select button to send the message. • Select CHG CALLEE to change the destination for the message. • Select TOD QUERY to get the time of day. 6.17.2 Radio TextLink Forms Form messages are displayed and stored in the radio as a message in which each field to be filled is indicated by a question mark (?) followed by one or more asterisks(*). The number of asterisks indicates the maximum number of alphanumeric characters allowed for that field. To send a Radio TextLink form: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the MESSAGES menu. 3. Press  or  to highlight TEXTLINK FORMS and press the Menu/Select button. 4. Press  or  to display the desired message and press the Menu/Select button. 5. Enter text into blank field(s) (up to eight alphanumeric characters) and press the NEXT soft key. 6. Select SEND to send the message. Select CHG CALLEE to change the destination for the message. Select TOD QUERY to get the time of day.

14221-1800-2000, Rev. F 86 6.17.3 View Received Messages When the icon appears on the idle display, there are Radio TextLink messages waiting to be read. To view received Radio TextLink messages: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the MESSAGES menu. 3. Press  or  to highlight TEXTLINK MAILBOX and press the Menu/Select button. From the mailbox, select OPTIONS to delete messages, view details of messages, and reply to messages. 6.18 FAULTS/ALERTS is displayed on the idle display when there is a fault. To view and clear faults/alerts: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the MESSAGES menu. 3. Press  or  to highlight FAULTS/ALERTS and press the Menu/Select button. 4. Fault messages are displayed. Press  or  to highlight the desired fault. Press the OPTIONS soft key delete faults. Press the DETAILS soft key to view details for the highlighted fault. Possible faults include: • BATTERY FAULT- Replace battery. • EEPROM FAULT - Contact Harris. • RF FAULT - Contact Harris. • OVERCURRENT - Check antenna and antenna connection. Try replacing antenna.

14221-1800-2000, Rev. F 87 • INVALID SYSTEM - Feature not installed. • CHANNEL FAULT - Channel frequency programmed is not valid for this radio. 5. If you view but do not delete the fault, the alert icon goes away on the idle display. Contact Harris for assistance with diagnosing a fault. 6.19 TONE ENCODE Tone Encode is a generic tone encoding scheme for call identification when transmitting on a conventional system. It supports generic user-definable tone encode (up to 15 tones), Type 99 (up to 2 tones) and 5/1 Tone (up to 5 tones) encoding formats. Tone encoding schemes are used to transmit calls to one or more target radios that have been programmed with the correct tone decode sequence. When the receiving radio detects its tone decode sequence, it unmutes on the call. To select a Tone Encode option: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the CALL menu. 3. Press  or  to highlight TONE ENCODE and press the Menu/Select button. 4. Select the desired Tone Encode option from the list. 6.20 ENCRYPTION 6.20.1 Create and Load Keys Refer to the following documentation for advanced programming and setup instructions: • Harris OTAR Overview Manual - MM-008069-001 • Network Key Manager Installation and Configuration Manual - MM-008070-001 • Harris UAS Key Management Application Manual - MM-008068-001 • Harris Key Manager Key Admin Overview and Operation Manual - MM1000019423 • Harris Key Manager Key Loader Overview and Operation Manual - MM1000019424 • Motorola® KVL 3000 Plus Key Variable Loader (KVL) User's Guide • Motorola KVL 4000 Key Variable Loader (KVL) User's Guide

14221-1800-2000, Rev. F 88 6.20.2 Zeroize Keys from Radio It may be necessary to remove keys because of compromise or expiration. To zeroize keys from the radio: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the SECURITY menu. 3. Press  or  highlight ZEROIZE KEYS and press the Menu/Select button. 4. Press the YES softkey to remove the keys. This will also remove the keysets. 6.20.3 Protected Keys The Protected Keys feature transfers P25 Voice Keys, from Harris Key Loader to the radio, that have been wrapped (AES) or encrypted (DES) with Key Protection Keys (KPKs). KPKs are nothing more than unprotected Key Encryption Keys (KEKs). The KPKs need to be loaded into the radio before the Protected Keys are loaded. Once loaded into the radio, the KPKs are used to unwrap (AES) or decrypt (DES) the Protected Keys. 6.20.4 Global Encryption Global Encryption can be enabled when encryption keys are loaded on the radio and the selected Zone/System is encrypted. When Global Encryption is enabled on the radio, a Global Key is used for all encrypted transmissions until: • Global Encryption is disabled. • A new personality is activated. • The active keyset is changed. • The system is changed.

14221-1800-2000, Rev. F 89 Global Encryption behavior is available on all channels that support encrypted communications. To enable Global Encryption and/or change Global Encryption Key: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the SECURITY menu. 3. Press  or  to highlight GLOBAL ENCRYPTION. Press the Menu/Select button. 4. Press  or  to highlight the desired Global Key and press the Menu/Select button to enable Global Encryption. 5. To change the selected global key, press  or  to highlight GLOBAL KEY on the SECURITY menu. Press the Menu/Select key. 6. Press  or  to highlight the global key and press the Menu/Select button. 7. RPM2 allows Key Numbers to be given Key Names. 8. The optional global key icon is displayed on the main display. 6.20.5 Select Keyset To select a keyset: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the SECURITY menu. 3. Press  or  to select ACTIVE KEYSET. Press the Menu/Select button to toggle to the inactive keyset.

14221-1800-2000, Rev. F 90 6.20.6 View Key List To view the key list: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the SECURITY menu. 3. Press  or  to select KEY LIST and press the Menu/Select button. 4. The available key lists are displayed. 6.20.7 Delete Individual Keys To delete individual keys from a keyset: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the SECURITY menu. 3. Press  or  to select KEY LIST and press the Menu/Select button. 4. The available key lists are displayed. 5. Select the desired keyset and press the Menu/Select button to display the individual keys. Highlight the desired key and press the Delete softkey.

14221-1800-2000, Rev. F 91 6.20.8 OTAR Configuration OTAR is the over-the-air-rekeying from a KMF and must be enabled for the digital only channel using RPM2. For OTAR operation, the appropriate KEKs must be loaded into the radio using the Harris Key Loader or a KVL device. The KMF Configuration must include the RSI of the KMF and the appropriate Message Number Period. To enable OTAR and request rekey: 1. Press the Menu/Select button to access the main menu. 2. Press  or  to display the SECURITY menu. 3. Press  or  to highlight OTAR and press the Menu/Select button to toggle ENABLED/DISABLED. 4. Press  or  to select OTAR REKEY and press the Menu/Select button to request that the KMF updates the keys in the radio. OTAR REKEY is only enabled if the radio has successfully registered for data operations. If enabled via programming, the radio plays an audible confirmation tone to indicate successful OTAR rekey.

14221-1800-2000, Rev. F 92 7. PROGRAMMING This section provides information on front panel programming. Programming can also be accomplished by creating a plan using a computer with RPM2 installed. 7.1 PROGRAMMING VIA RPM2 Radio Personality Manager (RPM2) is used for the bulk of programming the radio. With RPM2, you can fully program the XL-Portable using cable 12082-0410-A1. Removing power during radio programming, or programming the radio with low battery power could corrupt installation of firmware. Ensure that the radio is turned off before connecting the programming cable. After the cable is connected, then power on the radio. 7.2 EDIT CHANNEL (ANALOG AND P25 CONVENTIONAL ONLY) Channels can be edited from the Channel Information (CH INFO) menu display. Most of the displayed channel parameters can be modified here. Channel edits persist across a power cycle. Loading a personality clears any channel edits. Available parameters vary depending on whether the channel is a P25 or analog channel. To edit a channel: 1. From the main display, press  to access the CH INFO screen. 2. Press  or  to scroll through the programmed channel settings. 3. Press the EDIT soft key. Only authorized users should attempt channel editing. 4. Enter the password programmed via RPM2. You do not have to re-enter the password until you power cycle the radio. 5. Press the ENTER soft key. CAUTIONNOTECAUTION

14221-1800-2000, Rev. F 93 6. Highlight and select the parameter to edit. For P25 channels, modify remaining channel settings: • CHANNEL NAME - The Channel Name cannot be changed from this screen; RPM2 is required to change the Channel Name. • RX FREQUENCY - Receive frequency. Note that if the new frequency is invalid, the display reverts to the old frequency (Table 7-1). • TX FREQUENCY - Transmit frequency. • TX POWER - Transmit power. Toggle between LOW and HIGH. • TALKGROUP - Select a talkgroup for the channel. Talkgroup name cannot be set here. • RX NAC - Network Access Code (NAC) radio uses for Normal squelch in receive. • TX NAC - NAC radio transmits to break Normal squelch on receiving radio. • P25 SQUELCH - Select type the radio uses in receive. Select NORMAL, SELECTIVE, or MONITOR. • RX CHAN GUARD – Squelch type radio uses in receive. Select Noise, CTCSS, or CDCSS. For a digital channel, the RX CHAN GUARD is used to receive from a Conventional analog channel that is on the same frequency and uses the selected Channel Guard.  RX CODE - Code radio looks to unmute the speaker on the receiving radio when CDCSS squelch is used in conventional mode.  RX TONE - Tone radio looks to unmute the speaker on the receiving radio when CTCSS squelch is used in conventional mode. 7. For analog channel, modify remaining channel settings: • CHANNEL NAME - The Channel Name cannot be changed from this screen; RPM2 is required to change the Channel Name. • TX FREQUENCY - Transmit frequency. • TX POWER - Transmit power. Toggle between HIGH and LOW. • RX CHAN GUARD - Squelch type radio uses in receive. Select Noise, CTCSS, or CDCSS.  RX TONE - Tone radio uses to break selective squelch on receiving radio. This is available when RX squelch is set to CTCSS.  RX CODE - Code radio uses to break selective squelch on receiving radio. This is available when RX squelch is set to CDCSS. RX CHAN GUARD is not available on this screen if it was enabled from the CALL menu as per Section 5.22. • TX CHAN GUARD - Squelch type radio uses in transmit. Select None, CTCSS, or CDCSS. NOTE

14221-1800-2000, Rev. F 95 Table 7-2: Programmable Button Options FUNCTION DESCRIPTION No Operation Monitor Toggle Toggles Monitor On/Off. Monitor/Clear Temporarily turn off selected squelch to monitor for traffic that may not normally break squelch. Also, press this button followed by the emergency button to clear an emergency. Audio Playback Accesses the AUDIO PLAYBACK menu. See Section 5.27. Lock Keypad Locks the DTMF keypad, programmable function keys and navigation keys. Nuisance Delete Performs a Nuisance Delete. See Section 5.31 for more information. System Up Scrolls up through the list of available systems, stopping at the top of the list. System Down Scrolls down through the list of available systems, stopping when the end of the list is reached. System Up Wrap Scrolls up through the list of available systems, wrapping to the end when the beginning of the list is reached. System Down Wrap Scrolls down through the list of available systems, wrapping to the top when the bottom of the list is reached. Zone Up Scrolls up through the list of available mixed system zones, stopping at the top of the list. If no mixed system zones are defined, or there is only one, the user will hear a deny tone when the button is pressed. Zone Down Scrolls down through the list of available mixed system zones, stopping when the end of the list is reached. If no mixed system zones are defined, or there is only one, the user will hear a deny tone when the button is pressed. Zone Up Wrap Scrolls up through the list of available mixed system zones, wrapping to the end when the beginning of the list is reached. If no mixed system zones are defined, or there is only one, the user will hear a deny tone when the button is pressed. Zone Down Wrap Scrolls down through the list of available mixed system zones, wrapping to the top when the bottom of the list is reached. If no mixed system zones are defined, or there is only one, the user will hear a deny tone when the button is pressed. Channel/Group Bank Select Select the channel/group bank. If your system has more than 64 channels, this allows you to select a channel group with channels 65 to 127, 128 to 191, etc. Drop Call Drop or terminate any group call that the radio receives. Send Status Sends a preconfigured status. See Section 6.15 for more information. Send Message Sends a preconfigured message. See Section 6.16 for more information. TX Power High/Low Toggle TX Power between LOW and HIGH. Scan Enable Enable/disable scan. Secure Enable Toggle Toggles Encryption Mode On/Off. See Sections 5.20 and 6.20 for information on Encryption. Home Goes to home channel. Adjust Squelch Allows the user to adjust the analog squelch level. Front Backlight Toggles front display’s backlight On/Off/Momentary. Top Orient Toggles Top Display Front/Back. Top Backlight Toggles the top display’s backlight On/Off/Momentary. Flashlight Mode Press and hold to turn on the front and top display backlights. Release the button to turn off both displays. Speaker Mute Toggle Toggles Speaker Muted/Unmuted. Talkaround Toggles Talkaround On/Off. See Section 5.23. Voice Announce Enable/disable Voice Annunciation. See Section 5.19

14221-1800-2000, Rev. F 97 FUNCTION DESCRIPTION Keypad Lock Locks DTMF, programmable, and navigation soft keys. Radio Lock When set, prevents the radio software from responding to the following physical inputs on the radio: • Volume Knob Change (power off is not prevented) • 2-Position Switch • Channel Knob • Side User-Programmable Buttons and Keypad (DTMF, programmable, and navigation/soft keys) NOTE: Exception is the emergency button and if any key is programmed for Monitor/Clear, it can be used with the emergency button to clear emergency, if so programmed. Channel Bank Selects channels 1-16 in position A; 17-32 in position B; 33-48 in position C; and 49-64 in position D. If Channel Bank is selected for any single position, all 4 positions (A, B, C, and D) will be set to Channel Bank. 7.4.3.2 Indexed Features These features can be assigned to any number of positions as long as each index value selected for it is unique across multiple assignments of the same feature; for example, you cannot assign a Zone with a particular index (e.g., “ZONE A”) to both positions A and B. Table 7-5: Indexed Features FUNCTION DESCRIPTION Zone Selection Sets to the Zone index value. • When setting the A/B/C/D switch to an indexed zone assigned position, the radio sets, but does not “hold,” that zone. This has the resulting effects:  This sets the channel knob to be zone-based system/channel selection just like selecting a zone from the main “Zone” menu or ramping up/down using the side user-programmable buttons.  If a user then changes to a different system or zone via another method (menu, button, etc.), it will override the Zone selection switch setting accordingly and not require it to remain in the zone where the switch assignment is set. • When changing away from a Zone assigned position, no actions/changes will be taken by the radio. System Selection Sets to the System index value. • When setting the A/B/C/D switch to an indexed System assigned position, the radio sets, but does not “hold,” that System. This has the resulting effects:  This sets the channel knob to be system-based channel selection, just like selecting a system from the main “Zone” menu or ramping up/down using the side user-programmable buttons.  If a user then changes to a different system or zone via another method (menu, button, etc.), it will override the System selection switch setting accordingly and not require it to remain in the system where the switch assignment is set. • When changing away from a System assigned position, no actions/changes will be taken by the radio. 7.5 PROGRAMMABLE ICONS 7.5.1 Top display The top display has space for up to seven configurable icons, which can be programmed to display any of the following:

14221-1800-2000, Rev. F 98 • Blank • Signal Strength • Battery Status • Bluetooth enabled • Encryption enabled • Scan/Vote Scan enabled • Talkaround enabled • Emergency mode active The radio can be programmed to change the color of the top display backlight relative to the currently selected channel/group. The backlight remains the color programmed for the currently selected channel/group except during an emergency, in which case the color changes to orange. 7.5.2 Front display The front display has space for up to 10 configurable icons, which can be programmed to display any of the following: • Blank • Signal Strength • Battery Status • Bluetooth enabled • Encryption enabled • Global Encryption • Talkaround enabled • TX Disabled • Tones Disabled • PTT Disabled • Speaker Muted • Monitor • OTAR Status (Disabled, Registering, Registered, Rekeying) • TX Power level (Low/High/RX Only) • GPS Status • VDOC • Failsoft • Data Status (TX/RX) • Alert(s) • RX Mail • Noise Cancellation Enabled

14221-1800-2000, Rev. F 99 • Type 99 Enabled • Conventional Site Status (Unregistered/Registered)

14221-1800-2000, Rev. F 100 8. REFERENCE 8.1 MARINE FREQUENCIES Refer to Table 8-1: Marine Frequencies for a list of maritime frequencies per United States Coast Guard (USCG), National Oceanic and Atmospheric Administration (NOAA), and Canadian Department Fisheries and Oceans, August 2009: • United States (US) • International (Intl) • Canada (CA) Table 8-1: Marine Frequencies US CH. INTL CH. CA CH. SHIP (MHZ) SHORE (MHZ) CHANNEL USAGE 1 1 T: 156.05 R: 160.65 T: 160.65 R: 156.05 International: Public Correspondence, Port Operations 1a T/R: 156.05 T/R: 156.05 US: Port Operations and Commercial, Vessel Traffic Service (VTS). New Orleans/Lower Mississippi area. 2 2 T: 156.10 R: 160.70 T: 160.70 R: 156.10 International: Public Correspondence, Port Operations 3 3 T: 156.15 R: 160.75 T: 160.75 R: 156.15 International: Public Correspondence, Port Operations 4 T: 156.20 R: 160.80 T: 160.80 R: 156.20 International: Public Correspondence, Port Operations 4a T/R: 156.20 T/R: 156.20 Canada: Department Fisheries Ocean (DFO)/Canadian Coast Guard only in British Columbia coast area. Commercial fishing in east coast area 5 T: 156.25 R: 160.85 T: 160.85 R: 156.25 International: Public Correspondence, Port Operations 5a 5a T/R: 156.25 T/R: 156.25 US: Port Operations or VTS in Houston, New Orleans and Seattle areas. 6 6 6 T/R: 156.30 T/R: 156.30 US: Intership Safety International: Intership Canada: May be used for search and rescue communications between ships and aircraft. 7 T: 156.35 R: 160.95 T: 160.95 R: 156.35 International: Public Correspondence, Port Operations 7a 7a T/R: 156.35 T/R: 156.35 US: Commercial 8 8 8 T/R: 156.40 T/R: 156.40 US: Commercial (Intership only) International: Intership Canada: Also assigned for intership in the Lake Winnipeg area. 9 9 9 T/R: 156.45 T/R: 156.45 US: Boater Calling. Commercial and Non-Commercial. International: Intership, Port Operations Canada: Commercial - British Columbia coast area. May be used to communicate with aircraft and helicopters in predominantly maritime support operations.

14221-1800-2000, Rev. F 101 US CH. INTL CH. CA CH. SHIP (MHZ) SHORE (MHZ) CHANNEL USAGE 10 10 10 T/R: 156.50 T/R: 156.50 US: Commercial International: Intership, Port Operations Canada: Commercial - British Columbia coast area. May also be used for communications with aircraft engaged in coordinated search and rescue and antipollution operations. 11 11 11 T/R: 156.55 T/R: 156.55 US: Commercial. VTS in selected areas. International: Port Operations Canada: VTS - British Columbia coast area. Also used for pilotage purposes. 12 12 12 T/R: 156.60 T/R: 156.60 US: Port Operations. VTS in selected areas. International: Port Operations Canada: VTS - British Columbia coast area. Also used for pilotage purposes. 13 13 13 T/R: 156.65 T/R: 156.65 US: Intership Navigation Safety (Bridge-to-bridge). Ships >20m length maintain a listening watch on this channel in US waters. International: Intership, Port Operations Canada: VTS - British Columbia coast area. Also used for pilotage purposes. 14 14 14 T/R: 156.70 T/R: 156.70 US: Port Operations. VTS in selected areas. International: Port Operations Canada: VTS - British Columbia coast area. Also used for pilotage purposes. 15 15 15 T/R: 156.75 T/R: 156.75 US: Environmental (Receive only). Used by Class C Emergency Position-Indicating Radio Beacons (EPIRBs). International: Intership, Port Operations Canada: Port operations and Ship Movement - British Columbia coast area. All operations limited to 1-watt maximum power. May also be used for on-board communications. 16 16 16 T/R: 156.80 T/R: 156.80 US: International Distress, Safety and Calling. Ships required to carry radio, US Coast Guard (USCG), and most coast stations maintain a listening watch on this channel. International: International Distress, Safety and Calling Canada: International Distress, Safety and Calling 17 17 17 T/R: 156.85 T/R: 156.85 US: State Control International: Intership, Port Operations Canada: Port operations and Ship Movement - British Columbia coast area. All operations limited to 1 watt maximum power. May also be used for on-board communications. 18 T: 156.90 R: 161.50 T: 161.50 R: 156.90 International: Public Correspondence, Port Operations 18a 18a T/R: 156.90 T/R: 156.90 US: Commercial Canada: Towing - British Columbia coast area. 19 T: 156.95 R: 161.55* T: 161.55* R: 156.95 International: Public Correspondence, Port Operations 19a 19a T/R: 156.95 T/R: 156.95 US: Commercial Canada: DFO/Canadian Coast Guard. Pacific Pilots - British Columbia coast area. 20 20 20 T: 157.00 R: 161.60 T: 161.60 R: 157.00 US: Port Operations (Duplex) International: Public Correspondence, Port Operations Canada: Port operations only with 1 watt maximum power.

14221-1800-2000, Rev. F 102 US CH. INTL CH. CA CH. SHIP (MHZ) SHORE (MHZ) CHANNEL USAGE 20a T/R: 157.00 T/R: 157.00 US: Port Operations 21 T: 157.05 R: 161.65* T: 161.65* R: 157.05 International: Public Correspondence, Port Operations 21a 21a T/R: 157.05 T/R: 157.05 US: US Coast Guard only Canada: DFO/Canadian Coast Guard only. 21b - - T/R: 161.65 22 T: 157.10 R: 161.70 T: 161.70 R: 157.10 International: Public Correspondence, Port Operations 22a 22a T/R: 157.10 T/R: 157.10 US: Coast Guard Liaison and Maritime Safety Information Broadcasts. Broadcasts announced on channel 16. Canada: For communications between Canadian Coast Guard and non-Canadian Coast Guard stations only. 23 23 T: 157.15 R: 161.75 T: 161.75 R: 157.15 International: Public Correspondence, Port Operations 23a T/R: 157.15 T/R: 157.15 US: US Coast Guard only 23b - - T/R: 161.75 Canada: Continuous Marine Broadcast (CMB) service. 24 24 24 T: 157.20 R: 161.80 T: 161.80 R: 157.20 US: Public Correspondence (Marine Operator) International: Public Correspondence, Port Operations 25 25 25 T: 157.25 R: 161.85 T: 161.85 R: 157.25 US: Public Correspondence (Marine Operator) International: Public Correspondence, Port Operations Canada: Also assigned for operations in the Lake Winnipeg area. 25b T/R: 161.85 26 26 26 T: 157.30 R: 161.90 T: 161.90 R: 157.30 US: Public Correspondence (Marine Operator) International: Public Correspondence, Port Operations 27 27 27 T: 157.35 R: 161.95 T: 161.95 R: 157.35 US: Public Correspondence (Marine Operator) International: Public Correspondence, Port Operations 28 28 28 T: 157.40 R: 162.00 T: 162.00 R: 157.40 US: Public Correspondence (Marine Operator) International: Public Correspondence, Port Operations 28b - - T/R: 162.00 Canada: Continuous Marine Broadcast (CMB) service. 60 60 T: 156.025 R: 160.625 T: 160.625 R: 156.025 International: Public Correspondence, Port Operations 61 T: 156.075 R: 160.675 T: 160.675 R: 156.075 International: Public Correspondence, Port Operations 61a 61a T/R: 156.075 T/R: 156.075 Canada: DFO/Canadian Coast Guard only in British Columbia coast area. 62 T: 156.125 R: 160.725 T: 160.725 R: 156.125 International: Public Correspondence, Port Operations 62a T/R: 156.125 T/R: 156.125 Canada: DFO/Canadian Coast Guard only in British Columbia coast area.

14221-1800-2000, Rev. F 103 US CH. INTL CH. CA CH. SHIP (MHZ) SHORE (MHZ) CHANNEL USAGE 63 T: 156.175 R: 160.775 T: 160.775 R: 156.175 International: Public Correspondence, Port Operations 63a 63a T/R: 156.175 T/R: 156.175 US: Port Operations and Commercial, VTS. New Orleans/Lower Mississippi area. Canada: Tow Boats - British Columbia coast area. 64 64 T: 156.225 R: 160.825 T: 160.825 R: 156.225 International: Public Correspondence, Port Operations 64a 64a T/R: 156.225 T/R: 156.225 Canada: Commercial fishing only. 65 T: 156.275 R: 160.875 T: 160.875 R: 156.225 International: Public Correspondence, Port Operations 65a 65a T/R: 156.275 T/R: 156.275 US: Port Operations Canada: Search and rescue and antipollution operations on the Great Lakes. Towing on the Pacific Coast. Port operations only in the St. Lawrence River areas with 1 watt maximum power. Intership in inland Manitoba, Saskatchewan, and Alberta areas. 66 T: 156.325 R: 160.925 T: 160.925 R: 156.325 International: Public Correspondence, Port Operations 66a 66a T/R: 156.325 T/R: 156.325 US: Port Operations Canada: Port operations only in the St. Lawrence River/Great Lakes areas with 1 watt maximum power. 1 watt marina channel - British Columbia coast area. 67 67 67 T/R: 156.375 T/R: 156.375 US: Commercial. Used for Bridge-to-bridge communications in lower Miss. River. Intership only. International: Intership, Port Operations Canada: May also be used for communications with aircraft engaged in coordinated search and rescue and antipollution operations. Commercial fishing only in east coast and inland Manitoba, Saskatchewan, and Alberta areas. Pleasure craft - British Columbia coast area. 68 68 68 T/R: 156.425 T/R: 156.425 US: Non-Commercial International: Port Operations Canada: For marinas, yacht clubs and pleasure craft. 69 69 69 T/R: 156.475 T/R: 156.475 US: Non-Commercial International: Intership, Port Operations Canada: Commercial fishing only - east coast area. Pleasure craft - British Columbia coast area. 70 70 70 T/R: 156.525 T/R: 156.525 US: Digital Selective Calling (voice communications not allowed) International: Digital selective calling for distress, safety and calling Canada: Digital selective calling for distress, safety and calling 71 71 71 T/R: 156.575 T/R: 156.575 US: Non-Commercial International: Port Operations Canada: Ship Movement - British Columbia coast area. Marinas and yacht clubs - east coast and on Lake Winnipeg. 72 72 72 T/R: 156.625 T/R: 156.625 US: Non-Commercial (Intership only) International: Intership Canada: May be used to communicate with aircraft and helicopters in predominantly maritime support operations. Pleasure craft - British Columbia coast area

14221-1800-2000, Rev. F 104 US CH. INTL CH. CA CH. SHIP (MHZ) SHORE (MHZ) CHANNEL USAGE 73 73 73 T/R: 156.675 T/R: 156.675 US: Port Operations International: Intership, Port Operations Canada: May also be used for communications with aircraft engaged in coordinated search and rescue and antipollution operations. Commercial fishing only in east coast and inland Manitoba, Saskatchewan, and Alberta areas. 74 74 74 T/R: 156.725 T/R: 156.725 US: Port Operations International: Port Operations Canada: VTS and Ship Movement British Columbia coast area. 75 75 75 T/R: 156.775 T/R: 156.775 International: Port Operations Canada: Simplex port operation, ship movement and navigation related communication only. 1 watt maximum. 76 76 76 T/R: 156.825 T/R: 156.825 International: Port Operations Canada: Simplex port operation, ship movement and navigation related communication only. 1 watt maximum. 77 77 77 T/R: 156.875 T/R: 156.875 US: Port Operations (Intership only) International: Intership Canada: Pilotage - British Columbia coast area; 25 watts. Port operations only in the St. Lawrence River/Great Lakes areas with 1 watt maximum power. 78 T: 156.925 R: 161.525 T: 161.525 R: 156.925 International: Public Correspondence, Port Operations 78a 78a T/R: 156.925 T/R: 156.925 US: Non-Commercial Canada: Fishing Industry - British Columbia coast area. 79 T: 156.975 R: 161.575 T: 161.575 R: 156.975 International: Public Correspondence, Port Operations 79a 79a T/R: 156.975 T/R: 156.975 US: Commercial. Non-Commercial in Great Lakes only Canada: Fishing Industry - British Columbia coast area. 80 T: 157.025 R: 161.625 T: 161.625 R: 157.025 International: Public Correspondence, Port Operations 80a 80a T/R: 157.025 T/R: 157.025 US: Commercial. Non-Commercial in Great Lakes only Canada: Fishing Industry - British Columbia coast area. 81 T: 157.075 R: 161.675 T: 161.675 R: 157.075 International: Public Correspondence, Port Operations 81a 81a T/R: 157.075 T/R: 157.075 US: US Government only - Environmental protection operations Canada: DFO/Canadian Coast Guard use only. 82 T: 157.125 R: 161.725 T: 161.725 R: 157.125 International: Public Correspondence, Port Operations 82a 82a T/R: 157.125 T/R: 157.125 US: US. Government only Canada: DFO/Canadian Coast Guard use only. 83 T: 157.175 R: 161.775 T: 161.775 R: 157.175 International: Public Correspondence, Port Operations 83a 83a T/R: 157.175 T/R: 157.175 US: US Coast Guard only Canada: DFO/Canadian Coast Guard and other Government agencies. 83b - - T/R: 161.775

14221-1800-2000, Rev. F 105 US CH. INTL CH. CA CH. SHIP (MHZ) SHORE (MHZ) CHANNEL USAGE 84 84 84 T: 157.225 R: 161.825 T: 161.825 R: 157.225 US: Public Correspondence (Marine Operator) International: Public Correspondence, Port Operations 85 85 85 T: 157.275 R: 161.875 T: 161.875 R: 157.275 US: Public Correspondence (Marine Operator) International: Public Correspondence, Port Operations 86 86 86 T: 157.325 R: 161.925 T: 161.925 R: 157.325 US: Public Correspondence (Marine Operator) International: Public Correspondence, Port Operations 87 87 87 T: 157.375 R: 161.975 T: 161.975 R: 157.375 US: Automatic Identification System duplex repeater International: Port Operations Canada: Port operation and ship movement - east coast area. Pleasure craft - British Columbia coast area. 87a T/R: 157.375 T/R: 157.375 US: Public Correspondence (Marine Operator) 87b T/R: 161.975 T/R: 161.975 Canada: Automatic Ship Identification and Surveillance System. 88 88 T: 157.425 R: 162.025 T: 162.025 R: 157.425 US: Commercial, Intership only. International: Port Operations Canada: Port operation and ship movement - British Columbia coast area. 88a T/R: 157.425 T/R: 157.425 US: Commercial, Intership only. Canada: Automatic Ship Identification and Surveillance System. 88b T/R: 162.025 T/R: 162.025 WX1 WX1 R: 162.55 WX2 WX2 R: 162.4 WX3 WX3 R: 162.475 WX4 R: 162.425 WX5 R: 162.45 WX6 R: 162.5 WX7 R: 162.525 8.2 NARROWBANDING The FCC has mandated that all public safety radios manufactured after January 1, 2013 comply with narrowbanding restrictions. Radios manufactured after the above date will comply with these restrictions. Existing radio personalities that contain frequencies that violate these FCC rules will cause an invalid channel error indication on the radio display. The user will need to change the radio personality to comply with the new rules. Note that there are multiple exceptions to the narrowbanding mandate, including the Marine Frequencies listed in Section 8.1.

14221-1800-2000, Rev. F 106 9. GLOSSARY -A- AES Advanced Encryption Standard AES-256 Advanced Encryption Standard, 256-bit AMBE+2 Advanced Multi-Band Excitation implementation 2 ANSI American National Standards Institute ASCII American Standard Code for Information Interchange -B- -C- C Celsius CA Canada CDCSS Continuous Digital Coded Squelch System CH INFO Channel Information CKR Common Key References CMB Continuous Marine Broadcast CTCSS Continuous Tone Coded Squelch System -D- DES Digital Encryption Standard DES-OFB Digital Encryption Standard Output Feedback DFO Department Fisheries Ocean DMS Degrees Minutes Seconds -E- EPIRB Emergency Position-Indicating Radio Beacons -F- F Fahrenheit FCC Federal Communications Commission FM Frequency Modulation -G- GHz Giga (109) Hertz GEOTRANS Geographic Translator GPS Global Positioning System -H- Hz Hertz HKL Harris Key Loader -I- ID Identification IEEE Institute of Electrical & Electronics Engineers INTL International -J-

14221-1800-2000, Rev. F 107 -K- KEK Key Encryption Key kHz kilo (103) Hertz KID Key Identification KMF Key Management Facility KMS Key Management System KS Key Set KVL Key Variable Loader (Motorola KVL Device) -L- LAT/LONG DMS Latitude/Longitude Degrees Minutes Seconds LED Light Emitting Diode Li-ION Lithium-ION -M- MHz Megahertz mm Millimeter MR Mobile Radio ms milli (10-3) seconds -N- NAC Network Access Code Ni-MH Nickel Metal Hydride NOAA National Oceanic and Atmospheric Administration -O- OET Office of Engineering and Technology OTAR Over The Air Rekey -P- P25 Project 25 POS Position PRI Priority (Channel) PTT Push-to-Talk -Q- -R- RF Radio Frequency RPM2 Radio Personality Manager 2 RSI Radio Set Identifier RSM Remote Speaker Microphone RX Receive -S- SA Situational Awareness SMA Subminiature version A -T- TIA Telecommunications Industry Association TX Transmit

14221-1800-2000, Rev. F 108 -U- UHF Ultra High Frequency UKEK Unique Key Encryption Key US United States USCG United States Coast Guard UTC Universal Time Coordinated UTM Universal Transverse Mercator -V- VDC Volts, Direct Current VHF Very High Frequency VIDA Voice Interoperability Data Access VTS Vessel Traffic Service -W- WEEE Waste from Electric and Electronic Equipment -X- -Y- -Z-

14221-1800-2000, Rev. F 109 10. BASIC TROUBLESHOOTING When upgrading from XLP R1A/C to R1D/E, the radio displays . XLP R1D installs an image that is capable of installing future software releases and is required prior to upgrading to R2. Do not power cycle when this screen is displayed on the radio or R1D will have to be reinstalled prior to upgrading to R2. When installing XLP R2A and later, if the upgrade is interrupted by a power cycle, the radio displays . This indicates a partial install occurred and a reinstall is required. The radio should be connected via USB and the software should be installed again. For radios with XLP R3A and later, if is displayed, the radio has lost its factory information and needs to be returned for updating. 10.1 ERROR MESSAGES This section provides a list of error messages, as well as possible causes and solutions. Table 10-1: Displayed Error Messages, Reasons, and Resolutions SCREEN/ MENU DISPLAYED ERROR MESSAGE REASON RESOLUTION Top-Level Screen INVALID KEYSTORE ZEROIZE NEEDED Corrupt key database or incorrect database configuration. Zeroize database. Bluetooth Pairing Screen PAIRING FAILED Bluetooth pairing failed. Ensure device is discoverable and attempt to re-pair the device. Channel Edit Screen EDIT FAILED Unable to modify P25 Channel. Power cycle and try again--contact Harris if problem persists. Channel Edit Screen INVALID RX FREQUENCY Entered Rx frequency is invalid. Ensure frequency follows band spacing rules. Channel Edit Screen INVALID TX FREQUENCY Entered Tx frequency is invalid. Ensure frequency follows band spacing rules. Install Operations INSTALL FAILED Error during install process. Transfer file again and reattempt install. Contact Harris if problem persists. Install Operations INSTALL FAILED Extraction of compressed file failed. Transfer file again and reattempt install. Contact Harris if problem persists. Install Operations INSTALL FAILED Removal of existing SW failed. Attempt install again and contact Harris if problem persists. Mission Plan In Progress Screen Mission plan activation failed. Use RPM2 to ensure plan validity. Contact Harris if failures persist. Security Menu ZEROIZE FAILED Radio could not zeroize. Radio problem—power cycle and contact Harris if problem persists. Security Menu NO KEYS TO ZEROIZE Key database empty. Nothing to zeroize. Utilities Menu INCORRECT PASSWORD Maintenance password invalid. Enter valid maintenance password. Channel Info Screen INCORRECT PASSWORD Channel edit password invalid. Enter valid channel edit password.

14221-1800-2000, Rev. F 110 10.2 OTAR ERRORS/INFORMATION WORKAROUNDS: 1. Zeroize. 2. Load proper KEK from the Harris Key Loader or Motorola KVL. IF RADIO INDICATES: 1. INVALID KEYSTORE ZEROIZE NEEDED - This occurs if the radio’s keys were loaded by the Harris Key Loader followed by an attempt to load UKEKs with the Key Loader or keys with the Motorola KVL. - Fix by performing workaround 1, followed by 2. 2. NO UKEK – Displayed during a zeroize performed from the radio or a zeroize initiated from the KMF. - Fix by performing workaround 2. 3. Zeroize Complete – KMF has zeroized the radio. - Fix by performing workaround 2. 4. Disabled OTAR Icon (red slash) – OTAR is disabled while in scan, talkaround, emergency, and monitor. - Fix by disabling these features. Icon will be corrected (no red slash). 5. Gray OTAR Icon (no red slash) – OTAR has not registered with tower (Conventional or Trunked system). - Fix by verifying proper frequencies. - If the radio is turned to the OTAR channel out of range of a conventional tower, and then comes in range after 3 minutes, fix by issuing an OTAR. Rekey, leaving and re-enter the OTAR channel. 6. Green OTAR Icon – OTAR is registered, all is well. - If update fails, verify you are in range of the tower and the KEK is correct. 7. Blue OTAR Icon – OTAR is attempting to rekey. - If rekey fails, verify you are in range of the tower and the KEK is correct.

14221-1800-2000, Rev. F 111 11. TECHNICAL ASSISTANCE The Technical Assistance Center's (TAC) resources are available to help with overall system operation, maintenance, upgrades and product support. TAC is the point of contact when answers are needed to technical questions. Product specialists, with detailed knowledge of product operation, maintenance and repair provide technical support via a toll-free (in North America) telephone number. Support is also available through mail, fax and e-mail. For more information about technical assistance services, contact your sales representative, or contact the Technical Assistance Center directly: North America: 1-800-528-7711 International: 1-434-385-2400 Fax: 1-434-455-6712 E-mail: PSPC_tac@harris.com 12. WARRANTY Please register this product within 10 days of purchase. Registration validates the warranty coverage, and enables Harris to contact you in case of any safety notifications issued for this product. Registration can be made on-line at the Customer Care center webpage: https://www.harris.com//solution/pspc-customer-service While on the webpage, please review the applicable battery and/or product warranty literature.

14221-1800-2000, Rev. F 112 APPENDIX A WI-FI PROGRAMMING Due to numerous issues with discovering and programming radios connected to Enterprise Wireless networks, it is strongly suggested that a single Access Point Wireless network be used for programming radios with RPM2. See Section A.7 for more information. These instructions assume the user has a basic familiarity with Wireless (Wi-Fi) networks, their configuration, and how to connect devices. If you are unfamiliar with the terms and/or procedures mentioned in these instructions, please contact your IT department for help before attempting to configure Wi-Fi programming. For radios to be discoverable on the Wi-Fi network, your wireless router must be configured to allow Multicast (mDNS). This varies by router manufacturer; refer to your router’s documentation for specific settings needed to enable Multicast (mDNS). A.1 OVERVIEW Perform the following to program a radio over Wi-Fi. For first time setup, see Section A.8.1. 1. Configure the Access Point (Section A.2). 2. Configure the personality (Section A.3). 3. Configure the RPM2 application (Section A.4). 4. Put the radio in Wi-Fi Programming Mode (Section A.5). 5. Discovery and programming in the RPM2 application (Section A.6). 6. Support for Enterprise Wireless Networks (Section A.7). 7. Helpful Hints (Section A.8). CAUTIONNOTENOTE

14221-1800-2000, Rev. F 113 A.2 CONFIGURE THE ACCESS POINT • Setup an Access Point (wireless router) as follows. The bold values provided below are the default values in the personality.  Wireless Networking Name (SSID): harrisradios  Shared Key (Network Password): password  Wireless Authentication/Security Mode (Encryption Type): WPA WPA and WPA2-PSK are the available Encryption Types in the RPM2 application • Ensure that the Access Point has Multicast (mDNS) enabled. See the second note at the top of Appendix A for more information. The following are examples of how to allow Multicast (mDNS) message to be relayed and not filtered out on two different routers.  In the Buffalo Router (AC 1750), it is located in Advanced settings  Wireless  Multicast Control. Check the Enable checkbox beside “Snooping.”  In the Linksys router (WRT54GS), it is located under the Security tab. Uncheck “Filter Multicast” to prevent the Multicast (mDNS) messages from being filtered out. A.3 CONFIGURE THE PERSONALITY For a radio to be programmed over Wi-Fi, the active personality on the radio must be configured for connecting with the values that were set in Section A.2. The following steps detail how to configure an existing radio personality. 1. In the personality, navigate to Options  Network Configuration. Figure A-1: Options  Network Configuration 2. Under the Wi-Fi Configuration section, set the Encryption Type, Network (SSID), and Network Password. Figure A-2: Wi-Fi Configuration 3. Under Network Service Configuration, the default values can remain the same. If the wireless network is managed by another department, please coordinate with them to get it setup correctly.

14221-1800-2000, Rev. F 114 The Network Discovery Configuration  Service Name is a Unique name used by RPM2 and radios to communicate with each other. There is more information about this in Section A.8.2. Figure A-3: Service Name 4. After the personality is configured and saved, write it to the radio over USB and then activate it. A.4 CONFIGURE THE RPM2 APPLICATION To ensure that RPM2 can discover radios over Wi-Fi, ensure that the Enable Wi-Fi checkbox is checked on the RPM2 Preferences screen as shown in Figure A-4. This checkbox is unchecked by default. Figure A-4: Enable Wi-Fi in RPM2 Also as shown in Figure A-4, the Service Name must be updated to reference the value in the active personalities for the radios you need to discover. See #3 in Section A.3 and Section A.8.2 for more information. For default operation using the network as described in Section A.2, no other configuration of the radio or RPM2 is required.

14221-1800-2000, Rev. F 115 A.5 PUT THE RADIO IN WI-FI PROGRAMMING MODE To put the radio in Wi-Fi programming mode: 1. Turn the radio off and remove the USB cable (optional). 2. Press and hold the bottom side and PTT buttons. 3. Power on the radio while continuing to hold the buttons. 4. Release the buttons when the WIFI INSTALL ACTIVE screen appears on the radio. 5. Initially, the radio displays DISCONNECTED. When the IP address is displayed, the radio is available to be programmed. Figure A-5: Enable Wi-Fi Programming Mode on Radio A.6 DISCOVERY AND PROGRAMMING IN THE RPM2 APPLICATION 1. Start RPM2. 2. Disconnect the radio from the programming cable. 3. Select the Radio tab (Figure A-6) and click the Wi-Fi connection button as shown in Figure A-6.

14221-1800-2000, Rev. F 116 Figure A-6: RPM2 Radio Tab: Wi-Fi 4. When the Wi-Fi connection button is pressed, a “Discovering Wi-Fi Radios” message is displayed for several seconds and the radios connected to that access point with that Service Name populate the connection list. To connect over Wi-Fi, the currently active personality MUST have the correct Wi-Fi parameters. Therefore, care must be taken that all personalities on a given radio have the correct Wi-Fi parameters for the desired network. Otherwise, activation of another personality on the radio will result in the inability to establish a Wi-Fi connection. 5. Select a radio or radios and perform the desired action. Only Read Personality, Write Personality, and Load Code are supported over Wi-Fi. See the table below for the supported combinations. Table 12-1: Wi-Fi Feature Support SINGLE RADIO MULTIPLE RADIOS (UP TO 16) Read Single Personality Yes No Read Multiple Personalities Yes No Write Single Personality Yes Yes Write Multiple Personalities No No Load Single Code File Yes Yes Load Multiple Code Files Yes Yes Voice Annunciation No No Feature Data No No Radio Name Yes No Install Splash Screen Yes Yes 6. In the Status Panel, all Wi-Fi related actions will have the prefix of “WIFI.” To help in displaying the radios, the “Connection” and “IP Address” columns are sortable. If the Access Point is not configured to the default values from Section A.2 and the active personality in the radio is removed, the radio loses connection to the Access Point and must be connected over USB to write/activate a personality to reconnect to the Access Point. NOTENOTE

14221-1800-2000, Rev. F 117 A.7 RPM2 WI-FI SUPPORT FOR ENTERPRISE NETWORKS. Enterprise Networks have certain limitations when it comes to Discovering/Programming Radios in RPM2. There is a 4500 second (75 minute) caching affect inherent to implementation with the Cisco® Wi-Fi solution that utilizes the Access Point (AP)/Wireless LAN Controller (WLC) components. Radios remain ‘seen’ in RPM2 even after the radio leaves Wi-Fi or is turned off. It is cached in RPM2 for the 4500 second time period. This issue has only been observed with the Cisco AP and WLC solution, however other enterprise wireless solutions may observe this caching affect. Operation with a lower tiered Wi-Fi router that does not operate with a WLC will likely not observe this behavior. Please see Release Notes for Media Kit SK-019007-001 version R7A06 for more information. A.8 HELPFUL HINTS A.8.1 Initial Setup and Configuration Since radio discovery is dependent on whether or not Multicast (mDNS) messages are being received by RPM2, it is best to keep things as simple as possible. Here are the suggested steps if this is being setup and configured for the first time. 1. Configure the Access Point with the default personality values provided in Section A.2. 2. Create a basic personality with a single system, set and channel, write it to the radio and activate it over USB. 3. Complete Sections A.4 through A.6. If the radio was not discovered in RPM2 but an IP address is displayed on the radio screen as seen in Figure A-5, this may mean that the Multicast (mDNS) messages are not making it through the Access Point. Consult the Access Point’s manual and make sure that those messages are not being filtered out. A.8.2 Grouping Radios by Service Name One benefit of using a unique Service Name is that it allows the user to create logical groupings of radios in order to reduce the number of radios discovered in RPM2 and help reduce the overhead of keeping track of which radios have been configured. For example, if there are 100 radios in Wi-Fi programming mode (see Section A.5) with the same Service Name, all 100 radios are displayed in the Radio tab after discovery has been completed. This makes it difficult to select and program multiple radios simultaneously. However, if the Service Name in the active personality on 16 of the radios are set to something unique like “fire1” and the RPM2 application Service Name (see Section A.4) is also updated to “fire1,” only those radios with a Service Name of “fire1” are discovered and displayed in the Radio tab.

14221-1800-2000, Rev. F 118 This page intentionally left blank.

About Harris Corporation Harris Corporation is a leading technology innovator, solving customers’ toughest mission-critical challenges by providing solutions that connect, inform and protect. Harris supports government and commercial customers in more than 100 countries and has approximately $6 billion in annual revenue. The company is organized into three business segments: Communication Systems, Space and Intelligence Systems and Electronic Systems. Learn more at harris.com. FLORIDA NEW YORK VIRGINIA BRAZIL UNITED KINGDOM UAE SINGAPORE

Product Safety Manual 14221-1800-2010 Rev. D, April 2017 This booklet contains important safety information regarding specific absorption rate (SAR) and RF exposure limits included in United States and international standards. Read the information in this booklet before operating your radio. XL-200P Full-Spectrum Multiband XL-185P Single Band Portable Radios

14221-1800-2010, Rev. D 3 This product conforms to the European Union WEEE Directive 2012/19/EU. Do not dispose of this product in a public landfill. This product should be taken to a recycling center at the end of its life. Harris products comply with the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS) Directive. The voice coding technology embodied in this product is protected by intellectual property rights including patent rights, copyrights, and trade secrets of Digital Voice Systems, Inc. The user of this technology is explicitly prohibited from attempting to decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into human-readable form. Repairs to this equipment should be made only by an authorized service technician or facility designated by the supplier. Any repairs, alterations, or substitution of recommended parts made by the user to this equipment not approved by the manufacturer could void the user’s authority to operate the equipment in addition to the manufacturer’s warranty. This manual is published by Harris Corporation, without any warranty. Improvements and changes to this manual necessitated by typographical errors, inaccuracies of current information, or improvements to programs and/or equipment, may be made by Harris Corporation, at any time and without notice. Such changes will be incorporated into new editions of this manual. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose, without the express written permission of Harris Corporation. Copyright © 2015 - 2017 Harris Corporation.

4 14221-1800-2010, Rev. D This device is a RF transceiver intended for land mobile radio applications. The device may have use restrictions, which require that the national authority be contacted for any system licensing requirements, frequency use, allowable power level, etc. The LTE version of radio does not support operation outside the U.S. and Canada. NOTE

14221-1800-2010, Rev. D 5

6 14221-1800-2010, Rev. D

14221-1800-2010, Rev. D 7 Česky [Czech] Harris Corporation tímto prohlašuje, že tento XL-200P je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede Harris Corporation erklærer herved, at følgende udstyr XL-200P overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch [German] Hiermit erklärt Harris Corporation, dass sich das Gerät XL-200P in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti [Estonian] Käesolevaga kinnitab Harris Corporation seadme XL-200P vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. English Hereby, Harris Corporation, declares that this XL-200P is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Español [Spanish] Por medio de la presente Harris Corporation declara que el XL-200P cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Ελληνική [Greek] ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Harris Corporation ΔΗΛΩΝΕΙ ΟΤΙ XL-200P ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ. Français [French] Par la présente Harris Corporation déclare que l'appareil XL-200P est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.

8 14221-1800-2010, Rev. D Italiano [Italian] Con la presente Harris Corporation dichiara che questo XL-200P è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian] Ar šo Harris Corporation deklarē, XG 25P UHF-L(378-470 MHz), 7/800 (764-870MHz) atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. Lietuvių [Lithuanian] Šiuo Harris Corporation deklaruoja, kad šis XL-200P atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederlands [Dutch] Hierbij verklaart Harris Corporation dat het toestel XL-200P in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti [Maltese] Hawnhekk, Harris Corporation, jiddikjara li dan XL-200P jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Magyar [Hungarian] Alulírott, Harris Corporation nyilatkozom, hogy a XL-200P megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Polski [Polish] Niniejszym Harris Corporation oświadcza, że XL-200P jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Português [Portuguese] Harris Corporation declara que este XL-200P está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Slovensko [Slovenian] Harris Corporation izjavlja, da je ta XL-200P v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. Slovensky [Slovak] Harris Corporation týmto vyhlasuje, že XL-200P spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.

14221-1800-2010, Rev. D 9 Suomi [Finnish] Harris Corporation vakuuttaa täten että XL-200P tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Svenska [Swedish] Härmed intygar Harris Corporation att denna XL-200P står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. Íslenska [Icelandic] Hér með lýsir Harris Corporation yfir því að XL-200P er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC. Norsk [Norwegian] Harris Corporation erklærer herved at utstyret XL-200P er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.

10 14221-1800-2010, Rev. D TABLE OF CONTENTS Page 1. REGULATORY & SAFETY INFORMATION 11 1.1 SAFETY SYMBOL CONVENTIONS.......... 11 1.2 SAFETY TRAINING INFORMATION ....... 12 1.3 REGULATORY APPROVALS .................... 16 1.4 OPERATING TIPS ....................................... 17 2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ ............. 20 2.1 CONVENTIONS SUR LES SYMBOLES DE SÉCURITÉ .............................................. 20 2.2 RENSEIGNEMENTS SUR LA FORMATION SUR LA SÉCURITÉ ............. 21 2.3 INTERFÉRENCE DES RADIOFRÉQUENCES ................................. 24 2.4 CONSEILS D’UTILISATION ...................... 24 3. OPTIONS AND ACCESSORIES ....................... 28 4. BATTERY PACKS .............................................. 29 4.1 CONDITIONING LITHIUM-ION BATTERY PACKS ....................................... 30 4.2 STORING LI-ION BATTERY PACKS ........ 30 4.3 ADDITIONAL INFORMATION .................. 30 4.4 BATTERY DISPOSAL ................................. 30 5. TECHNICAL ASSISTANCE .............................. 32 6. WARRANTY ....................................................... 33 Harris Corporation, Public Safety and Professional Communications (PSPC) Business continually evaluates its technical publications for completeness, technical accuracy, and organization. You can assist in this process by submitting your comments and suggestions to the following: Harris Corporation PSPC Business Technical Publications 221 Jefferson Ridge Parkway Lynchburg, VA 24501 Or Fax your comments to: 1-434-455-6851 Or E-mail us at: PSPC_TechPubs@harris.com

14221-1800-2010, Rev. D 11 1. REGULATORY & SAFETY INFORMATION 1.1 SAFETY SYMBOL CONVENTIONS The following conventions are used to alert the user to general safety precautions that must be observed during all phases of operation, service, and repair of this product. Failure to comply with these precautions or with specific warnings elsewhere violates safety standards of design, manufacture, and intended use of the product. Harris assumes no liability for the customer's failure to comply with these standards. The WARNING symbol calls attention to a procedure, practice, or the like, which, if not correctly performed or adhered to, could result in personal injury. Do not proceed beyond a WARNING symbol until the conditions identified are fully understood or met. The CAUTION symbol calls attention to an operating procedure, practice, or the like, which, if not performed correctly or adhered to, could result in a risk of danger, damage to the equipment, or severely degrade the equipment performance. The NOTE symbol calls attention to supplemental information, which may improve system performance or clarify a process or procedure. WARNINGCAUTIONNOTE

12 14221-1800-2010, Rev. D 1.2 SAFETY TRAINING INFORMATION The Harris XL-200P/XL-185P portable radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only,” meaning it must be used only during the course of employment by individuals aware of the hazards and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment. The XL-200P/XL-185P portable radio has been tested and complies with the FCC RF exposure limits for “Occupational Use Only.” In addition, this radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans: • FCC KDB Publication 447498 General RF Exposure Guidance • American National Standards Institute (C95.1 – 19921), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. • American National Standards Institute (C95.3 – 1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields – RF and Microwave. • IC Standard RSS-102. Radio frequency Exposure Compliance of Radio communication Apparatus (All Frequency Bands). 1 Tested to ANSI C95.1-1992 in compliance with 47 CFR 2.1093. Meets or exceeds safety requirements of ANSI C95.1-2005. WARNING

14221-1800-2010, Rev. D 13 • European Council Directive 89/391/EEC. 1.2.1 RF Exposure Guidelines To ensure that exposure to RF electromagnetic energy is within the EU/AU/FCC/IC allowable limits for occupational use, always adhere to the following guidelines: • DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may also cause the FCC RF exposure limits to be exceeded. A proper antenna is the antenna supplied with this radio by Harris or an antenna specifically authorized by Harris for use with this radio. • DO NOT transmit for more than 50% of total radio use time (“50% duty cycle”). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the “TX” indicator appears in the display. The radio will transmit by pressing the “PTT” (Push-To-Talk) button. • ALWAYS transmit using low power when possible. In addition to conserving battery charge, low power can reduce RF exposure. • ALWAYS use Harris authorized accessories (antennas, batteries, belt clips, speaker/mics, etc.). Use of unauthorized accessories may cause the FCC Occupational/Controlled Exposure RF compliance requirements to be exceeded. (Refer to Table 1-1.) • As noted in Table 1-1, ALWAYS keep the housing of the transmitter AT LEAST 0.47 inches (1.2 cm) from the body and at least 0.98 inches (2.5 cm) from the face when transmitting to ensure FCC RF exposure compliance requirements are not exceeded. However, to provide the best sound quality to the recipients of your transmission, Harris recommends you CAUTION

14 14221-1800-2010, Rev. D hold the microphone at least 5 cm (2 inches) from mouth, and slightly off to one side. • Refer to Standard EN 62311:2008. Table 1-1: RF Exposure Compliance Tested Distances2 RADIO FREQUENCY BAND TESTED DISTANCES (worst case scenario) Body3 Face VHF (136 - 174 MHz) 0.47 in (1.2 cm) 0.98 in (2.5 cm) UHF (378 - 522 MHz) 0.47 in (1.2 cm) 0.98 in (2.5 cm) 700/800 MHz (768 - 776 MHz) (798 - 806 MHz) (806 - 824 MHz) (851 - 870 MHz) 0.47 in (1.2 cm) 0.98 in (2.5 cm) 900 MHz (935-944 MHz) (896-902 MHz) 0.47 in (1.2 cm) 0.98 in (2.5 cm) 2400 MHz (2412 - 2472 MHz) 0.47 in (1.2 cm) 0.98 in (2.5 cm) 5 GHz (5.18 - 5.825 GHz) 0.47 in (1.2 cm) 0.98 in (2.5 cm) SAR Evaluation: 1g averaged, 50% PTT Duty Factor, Occupational/ Controlled Exposure. 2 Minimum safe operating distances for the radio are based on the Harmonized Standards and SAR evaluation. 3 This is worst case based on the thinnest body mount accessory (belt clip). NOTE

14221-1800-2010, Rev. D 15 This device contains multiple transmitters that may operate simultaneously, see Table 1-3 Simultaneous Transmission Scenarios for the capable transmit configurations. Table 1-2: Simultaneous Transmission Scenarios NO. CAPABLE TRANSMIT CONFIGURATION HEAD BODY-WORN ACCESSORY 1 LTE B13/14/4 + VHF YES YES 2 LTE B13/14/4 + UHF YES YES 3 LTE B4 + 700 MHz YES YES 4 LTE B13/14/4 + 800 MHz YES YES 5 LTE B13/14/4 + Bluetooth YES YES 6 LTE B13/14/4 + 2.4 GHz WLAN YES YES 7 LTE B13/14/4 + 5 GHz WLAN YES YES 8 LTE B13/14/4 + VHF + Bluetooth YES YES 9 LTE B13/14/4 + UHF + Bluetooth YES YES 10 LTE B4 + 700 MHz + Bluetooth YES YES 11 LTE B13/14/4 + 800 MHz + Bluetooth YES YES 12 LTE B13/14/4 + VHF + WLAN YES YES 13 LTE B13/14/4 + UHF + WLAN YES YES 14 LTE B4 + 700 MHz + WLAN YES YES 15 LTE B13/14/4 + 800 MHz + WLAN YES YES 16 LTE B13/14/4 + 900 MHz (XL-185P Only) YES YES 17 LTE B13/14/4 + 800 MHz + Bluetooth YES YES 18 LTE B13/14/4 + 800 MHz + WLAN YES YES

16 14221-1800-2010, Rev. D LTE B13/14 + 700 MHz combination is not supported by this device. The information in this section provides the information needed to make the user aware of a RF exposure, and what to do to assure that this radio operates within the FCC RF exposure limits. 1.2.2 Electromagnetic Interference/Compatibility During transmissions, Harris radios generate RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radios in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites. 1.3 REGULATORY APPROVALS Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. 1.3.1 Part 15 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. 1.3.2 Industry Canada This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept NOTE

14221-1800-2010, Rev. D 17 any interference, including interference that may cause undesired operation of the device. 1.4 OPERATING TIPS Antenna location and condition are important when operating a portable radio. Operating the radio in low lying areas or terrain, under power lines or bridges, inside of a vehicle or in a metal framed building can severely reduce the range of the unit. Mountains can also reduce the range of the unit. In areas where transmission or reception is poor, some improvement may be obtained by ensuring the antenna is vertical. Moving a few yards in another direction or moving to a higher elevation may also improve communications. Vehicular operation can be aided with the use of an externally mounted antenna. Battery condition is another important factor in the trouble free operation of a portable radio. Always properly charge the batteries. 1.4.1 Efficient Radio Operation Keep the antenna in a vertical position when receiving or transmitting a message. Do NOT hold onto the antenna when the radio is powered on. 1.4.2 Antenna Care and Replacement Always keep the antenna at least 0..47 inches (1.2 cm) away from the body and 0.98 inches (2.5 cm) from the face when transmitting to ensure FCC RF exposure compliance requirements are not exceeded. WARNINGWARNING

18 14221-1800-2010, Rev. D Do not use the portable radio with a damaged or missing antenna. A minor burn may result if skin comes into contact with a damaged antenna. Replace a damaged antenna immediately. Operating a portable radio with the antenna missing could cause personal injury, damage the radio, and may violate FCC regulations. Use only the supplied or approved antenna. Unauthorized antennas, modifications, or attachments could cause damage to the radio unit and may violate FCC regulations. 1.4.3 Electronic Devices RF energy from portable radios may affect some electronic equipment. Most modern electronic equipment in cars, hospitals, homes, etc., are shielded from RF energy. However, in areas in which you are instructed to turn off two-way radio equipment, always observe the rules. If in doubt, turn it off! 1.4.4 Aircraft Always turn off a portable radio before boarding any aircraft! • Use it on the ground only with crew permission. • DO NOT use while in-flight!! WARNINGCAUTIONCAUTIONWARNING

14221-1800-2010, Rev. D 19 1.4.5 Electric Blasting Caps To prevent accidental detonation of electric blasting caps, DO NOT use two-way radios within 1000 feet of blasting operations. Always obey the "Turn Off Two-Way Radios" signs posted where electric blasting caps are being used. (OSHA Standard: 1926.900) 1.4.6 Potentially Explosive Atmospheres Areas with potentially explosive atmospheres are often, but not always, clearly marked. These may be fuelling areas, such as gas stations, fuel or chemical transfer or storage facilities, and areas where the air contains chemicals or particles, such as grain, dust, or metal powders. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Turn OFF two-way radios when in any area with a potentially explosive atmosphere. It is rare, but not impossible that a radio or its accessories could generate sparks. DO NOT remove, install, or charge batteries in potentially explosive atmosphere areas. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. WARNINGWARNINGWARNING

20 14221-1800-2010, Rev. D 2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ 2.1 CONVENTIONS SUR LES SYMBOLES DE SÉCURITÉ Les conventions suivantes sont utilisées dans le présent manuel pour avertir l’utilisateur des précautions générales de sécurité qui doivent être observées pendant toutes les phases d’opération, d’entretien et de réparation de ce produit. Le non-respect de ces précautions ou d’avertissements précisés ailleurs enfreint les normes de sécurité de la conception, de la fabrication et de l’utilisation prévue du produit. Harris n’assume aucune responsabilité pour le non-respect de ces normes par le client. MISE EN GARDE Le symbole MISE EN GARDE attire l’attention sur une procédure ou une pratique qui, si elle n’est pas correctement effectuée ou observée, pourrait entraîner une blessure personnelle. Ne pas poursuivre au-delà d’un symbole de MISE EN GARDE avant que les conditions identifiées soient complètement comprises ou satisfaites. AVERTISSEMENT Le symbole AVERTISSEMENT attire l’attention sur une procédure ou une pratique opérationnelle qui, si elle n’est pas correctement effectuée ou observée, pourrait entraîner un bris d’équipement ou une importante baisse de rendement de l’équipement.

14221-1800-2010, Rev. D 21 REMARQUE Le symbole REMARQUE attire l’attention sur des renseignements supplémentaires qui peuvent améliorer le rendement du système ou clarifier un processus ou une procédure. 2.2 RENSEIGNEMENTS SUR LA FORMATION SUR LA SÉCURITÉ MISE EN GARDE La radio portative Harris XL-200P/XL-185P produit de l’énergie électromagnétique des RF lorsqu’en mode de transmission. Cette radio est conçue et classée pour une « Utilisation professionnelle seulement », ce qui signifie qu’elle ne doit être utilisée que dans le cadre d’un emploi par des individus conscients des risques et des moyens de limiter ceux-ci. Cette radio N’EST PAS conçue pour une utilisation par la « Population générale » dans un environnement non contrôlé. La radio portative XL-200P/XL-185P a été testée et est conforme aux limites d’exposition aux RF de la FCC pour une « Utilisation professionnelle seulement ». De plus, cette radio Harris est conforme aux normes et directives suivantes quant à l’énergie des RF et aux niveaux d’énergie électromagnétique, ainsi qu’à l’évaluation de ces niveaux pour l’exposition aux humains: • FCC KDB 447498 • American National Standards Institute (C95.1 – 1992), norme de l’IEEE sur les niveaux sécuritaires d’exposition humaine aux champs électromagnétiques des radiofréquences, 3 kHz à 300 GHz.

22 14221-1800-2010, Rev. D • American National Standards Institute (C95.3 – 1992), pratique recommandée par l’IEEE pour la mesure des champs électromagnétiques potentiellement dangereux – RF et micro-ondes. 2.2.1 Directives sur l’exposition aux RF AVERTISSEMENT Pour s’assurer que l’exposition à l’énergie électromagnétique des RF se situe dans les limites acceptables de la FCC pour l’utilisation professionnelle, respectez toujours les directives suivantes : • N’utilisez PAS la radio sans qu’une antenne appropriée y soit connectée, car ceci peut endommager la radio et également causer un dépassement des limites d’exposition aux RF de la FCC. Une antenne appropriée est celle fournie par Harris avec cette radio, ou une antenne spécifiquement autorisée par Harris pour être utilisée avec cette radio. • Ne transmettez PAS pendant plus de 50 % de la durée d’utilisation totale de la radio (« cycle de service de 50 % »). La transmission pendant plus de 50 % du temps peut causer un dépassement des exigences de conformité de la FCC en matière d’exposition aux RF. La radio transmet lorsque l’indicateur « TX » apparaît sur l’affichage. La radio transmet lorsqu’on appuie sur le bouton « PTT » (bouton de microphone). • Transmettez TOUJOURS en basse puissance lorsque possible. En plus de préserver la charge de la pile, une faible puissance réduit l’exposition aux RF. • Utilisez TOUJOURS des accessoires autorisés Harris (antennes, piles, pinces de ceinture, haut-parleurs/micros, etc.). L’utilisation d’accessoires non autorisés peut entraîner un dépassement des

14221-1800-2010, Rev. D 23 exigences de conformité pour une exposition aux RF professionnelle ou contrôlée de la FCC. (Reportez-vous à Tableau 2-1.) • Tel qu’indiqué dans Tableau 2-1, conservez TOUJOURS l’appareil et son antenne à AU MOINS 1,2 cm (0,47 po) du corps, et à au moins 2,5 cm (0,98 po) du visage pendant la transmission, pour vous assurer de ne pas dépasser les exigences de conformité de la FCC en matière d’exposition aux RF. Cependant, pour offrir la meilleure qualité sonore aux auditeurs de votre transmission, Harris recommande de tenir le microphone à au moins 5 cm (2 po) de votre bouche et légèrement déplacé sur un côté. Tableau 2-1 : Distances de test de conformité des expositions aux RF RADIOFRÉQUENCES DISTANCES TESTÉES (pire des scénarios) Corps4 Visage VHF (136 - 174 MHz) 1,2 cm 2,5 cm UHF (378 - 522 MHz) 1,2 cm 2,5 cm 700/800 MHz (768 - 776 MHz) (798 - 806 MHz) (806 - 824 MHz) (851 - 870 MHz) 1,2 cm 2,5 cm 900 MHz (935-944 MHz) (896-902 MHz) 1,2 cm 2,5 cm 2400 MHz (2412 - 2472 MHz) 1,2 cm 2,5 cm 5 GHz (5.18 - 5.825 GHz) 1,2 cm 2,5 cm Dans cette section figurent les renseignements nécessaires pour sensibiliser l’utilisateur à l’exposition aux RF et sur ce qu’il faut faire pour 4 Ce est le pire des cas basée sur le corps plus mince monter accessoire (clip ceinture).

24 14221-1800-2010, Rev. D s’assurer que cette radio fonctionne dans les limites d’exposition aux RF de la FCC. 2.2.2 Interférence/Compatibilité Électromagnétique Pendant les transmissions, cette radio Harris produit de l’énergie des RF qui peut causer de l’interférence avec d’autres appareils ou systèmes. Pour éviter de telles interférences, fermez la radio dans les zones où il est indiqué de le faire. N’utilisez PAS le transmetteur dans des zones sensibles aux radiations électromagnétiques, comme les hôpitaux, les avions et les sites de détonation. 2.3 INTERFÉRENCE DES RADIOFRÉQUENCES 2.3.1 Partie 15 de la FCC Cet appareil est conforme à la Partie 15 de la réglementation de la FCC. Le fonctionnement est soumis aux deux conditions suivantes : 1. Cet appareil ne doit pas causer une interférence nuisible; et 2. Cet appareil doit accepter toute interférence reçue, y compris une interférence qui peut causer un fonctionnement non souhaité. 2.3.2 Industrie Canada Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. 2.4 CONSEILS D’UTILISATION L’emplacement et l’état de l’antenne sont importants pour l’utilisation d’une radio portative. L’utilisation de la radio dans des zones de faible élévation, sous des lignes électriques ou des ponts, à l’intérieur d’un

14221-1800-2010, Rev. D 25 véhicule ou dans un immeuble à ossature métallique, peut réduire la portée de l’appareil de manière considérable. Les montagnes peuvent également réduire la portée de l’unité. Dans les zones où la transmission ou la réception est insatisfaisante, certaines améliorations peuvent être obtenues en s’assurant que l’antenne est verticale. Se déplacer de quelques mètres dans une autre direction ou à un emplacement plus élevé peut également améliorer les communications. L’utilisation d’une antenne fixée à l’extérieur peut faciliter le fonctionnement dans un véhicule. L’état de la pile est un autre facteur important d’une utilisation sans tracas d’une radio portative. Chargez toujours correctement la pile. 2.4.1 Utilisation Efficace de la Radio Gardez l’antenne dans une position verticale pendant la réception ou la transmission d’un message. MISE EN GARDE Ne tenez PAS l’antenne lorsque la radio est allumée! 2.4.1.1 Entretien et Remplacement de l’antenne MISE EN GARDE Conservez TOUJOURS l’appareil et son antenne à au moins 1,5 cm (0,59 po) du corps, et à au moins 2,5 cm (1,0 po) du visage pendant la transmission, pour vous assurer de ne pas dépasser les exigences de conformité de la FCC en matière d’exposition aux RF.

26 14221-1800-2010, Rev. D MISE EN GARDE N’utilisez pas la radio portative si son antenne est endommagée ou absente. Une brûlure légère peut se produire au contact d’une antenne endommagée avec la peau. Remplacez immédiatement une antenne endommagée. L’utilisation d’une radio portative alors que l’antenne est absente peut causer des blessures, endommager la radio et pourrait enfreindre la réglementation de la FCC. AVERTISSEMENT Utilisez seulement l’antenne fournie ou une antenne approuvée. Des antennes non autorisées, des modifications ou des ajouts à une antenne peuvent endommager la radio et enfreindre la réglementation de la FCC. 2.4.1.2 Appareils Électroniques AVERTISSEMENT L’énergie des RF provenant de radios portatives peut affecter certains appareils électroniques. La majorité de l’équipement électronique moderne dans les voitures, les hôpitaux, les maisons, etc. est blindé contre l’énergie des RF. Cependant, dans les zones où l’on vous demande de fermer l’équipement de radio bidirectionnelle, respectez toujours les règles. En cas de doute, éteignez-le!

14221-1800-2010, Rev. D 27 2.4.1.3 Avion MISE EN GARDE • Éteignez toujours une radio portative avant d’embarquer à bord d’un avion! • Ne l’utilisez au sol qu’avec la permission de l’équipage. • NE l’utilisez PAS durant le vol! 2.4.1.4 Détonateurs électriques MISE EN GARDE Pour prévenir la détonation accidentelle des détonateurs électriques, n’utilisez PAS de radios bidirectionnelles à moins de 305 m (1 000 pi) des opérations de détonation. Respectez toujours les indications « Éteindre les radios bidirectionnelles » situées là où des détonateurs électriques sont utilisés. (Norme OSHA : 1926.900)

28 14221-1800-2010, Rev. D 2.4.1.5 Atmosphère Potentiellement Explosive MISE EN GARDE Les zones ayant une atmosphère potentiellement explosive sont souvent, mais pas toujours, identifiées clairement comme telles. Il peut s’agir de zones d’alimentation en carburant, comme les postes d’essence, les installations de stockage ou de transfert de carburant ou de produits chimiques, ainsi que les zones dont l’air contient des produits chimiques ou des particules, comme des grains, de la poussière ou des poudres métalliques. Des étincelles dans de telles zones peuvent provoquer une explosion ou un incendie, causant ainsi des blessures ou même la mort. Éteignez les radios bidirectionnelles dans toute zone ayant une atmosphère potentiellement explosive. Il est rare, mais pas impossible qu’une radio ou ses accessoires produisent des étincelles. 3. OPTIONS AND ACCESSORIES A complete list of Options and Accessories approved for use with the XL-200P/XL-185P portable radio can be found online in the Operator’s Manual 14221-1800-2000 at www.harris.com/solution/xl-200p-two-way-portable-radio. Also reference the Products and Services Catalog for all available options and accessories, including those items that do not adversely affect the RF energy exposure.

14221-1800-2010, Rev. D 29 Always use Harris authorized accessories (antennas, batteries, belt clips, speaker/mics, etc). Use of unauthorized accessories may cause the FCC Occupational/Controlled Exposure RF compliance requirements to be exceeded. Always use the correct options and accessories (battery, antenna, speaker/mic, etc.) for the radio. See Operator Manual 14221-1800-2000, available online at www.harris.com/solution/xl-200p-two-way-portable-radio, for the list of accessories. 4. BATTERY PACKS The XL-200P/XL-185P series portable radios use rechargeable, recyclable Lithium-Ion (Li-Ion) battery packs. Please follow the directions below to maximize the useful life of each type of battery pack. Do not disassemble or modify Lithium battery packs. The Lithium battery packs are equipped with built-in safety and protection features. Should these features be disabled or tampered with in any way, the battery pack can leak electrolyte, overheat, emit smoke, burst, and/or ignite. If the battery pack is ruptured or is leaking electrolyte that results in skin or eye contact with the electrolyte, immediately flush the affected area with water. If the battery electrolyte gets in the eyes, flush with water for 15 minutes and consult a physician immediately. WARNINGCAUTIONWARNINGWARNING

30 14221-1800-2010, Rev. D Always use Harris authorized chargers and conditioners. Use of unauthorized chargers and conditioners may void the warranty. 4.1 CONDITIONING LITHIUM-ION BATTERY PACKS Li-Ion battery packs do not suffer from memory effect and therefore do not require conditioning. 4.2 STORING LI-ION BATTERY PACKS If a battery pack is expected to be idle for a month or more, it should be properly prepared. Li-Ion battery packs should not be stored fully charged. Before storing the battery pack, discharge it to 40% capacity. If the battery is not discharged prior to storage, its overall capacity may be reduced. Although all battery packs experience some capacity loss during storage, the shelf life for Li-Ion battery packs is about 3 months. However, note that any capacity drop which occurs during storage is permanent and cannot be reversed. Li-Ion battery packs should be purchased and used immediately. They should not be stock-piled without a rotating stock plan. 4.3 ADDITIONAL INFORMATION For more information regarding the proper care of portable radio battery packs or establishing a battery maintenance program, refer to ECR-7367 which may be ordered by calling toll free 1-800-368-3277 (international - 1-434-455-6403) or via https://premier.pspc.harris.com/infocenter/. 4.4 BATTERY DISPOSAL In no instance should a battery pack be incinerated. Disposing of a battery pack by burning will cause an explosion. CAUTIONCAUTION

14221-1800-2010, Rev. D 31 RECHARGEABLE BATTERY PACK DISPOSAL – The product you have purchased contains a rechargeable battery pack. The battery pack is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery pack into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal. Canadian and U.S. users may call Toll Free 1-800-8-BATTERY® for information and/or procedures for returning rechargeable batteries in your locality.

32 14221-1800-2010, Rev. D 5. TECHNICAL ASSISTANCE The Technical Assistance Center's (TAC’s) resources are available to help with overall system operation, maintenance, upgrades and product support. TAC is your point of contact when answers are needed to technical questions. Product specialists, with detailed knowledge of product operation, maintenance, and repair, provide technical support via a toll-free (in North America) telephone number. Support is also available through mail, fax and e-mail. For more information about technical assistance services, contact your sales representative, or call the Technical Assistance Center directly at: North America: 1-800-528-7711 International: 1-434-385-2400 Fax: 1-434-455-6712 E-mail: PSPC_tac@harris.com

14221-1800-2010, Rev. D 33 6. WARRANTY If any part of the system equipment is damaged on arrival, contact the shipper to conduct an inspection and prepare a damage report. Save the shipping container and all packing materials until the inspection and the damage report are completed. In addition, contact the Customer Care center to make arrangements for replacement equipment. Do not return any part of the shipment until you receive detailed instructions from a Harris representative. North America: Phone Number: 1-800-368-3277 Fax Number: 1-321-409-4393 E-mail: PSPC_CustomerFocus@harris.com International: Phone Number: 1-434-455-6403 Fax Number: 1-321-409-4394 E-mail: PSPC_InternationalCustomerFocus@harris.com Please register this product within 10 days of purchase. Registration validates the warranty coverage, and enables Harris to contact you in case of any safety notifications issued for this product. Registration can be made on-line at the Customer Care center webpage: https://www.harris.com//solution/pspc-customer-service While on the webpage, please review the applicable battery and/or product warranty literature.

34 14221-1800-2010, Rev. D NOTES

About Harris Corporation Harris Corporation is a leading technology innovator, solving customers’ toughest mission-critical challenges by providing solutions that connect, inform and protect. Harris supports government and commercial customers in more than 100 countries and has approximately $6 billion in annual revenue. The company is organized into three business segments: Communication Systems, Space and Intelligence Systems and Electronic Systems. Learn more at harris.com. FLORIDA NEW YORK VIRGINIA BRAZIL UNITED KINGDOM UAE SINGAPORE

Navigation menu