Guangzhou Shirui Electronics R812USA2 WIFI module User Manual

Guangzhou Shirui Electronics Co., Ltd WIFI module Users Manual

Users Manual

WIFI-2-R812USA2 IEEE 802.11a/ b/g/n/ac 2T2R USB2.0 WiFi Module 特性 Features： ¾ 接收制式 Reserving System IEEE Std. 802.11a IEEE Std. 802.11b IEEE Std. 802.11g IEEE Std. 802.11n IEEE Std. 802.11ac ¾ 双波段 Dual Band 2.4G&5.8G ¾ 结构大小 Size 27.00mm x 17.80mm x 3.7mm 四川爱联科技有限公司 Sichuan iLink Technology Co.,Ltd 地址 Add: 四川省绵阳市安州工业园区 Anzhou,Industrial park,Mianyang,Sichuan 传真 Fax : +86-0816-2416943 网 址: http://www.changhong.com 技术 热线：
WIFI-2-R812USA2 Dual Band 11ac USB WiFi Module with RTL8812AU 四川爱联科技有限公司 Sichuan iLink Technology Co.,Ltd. page 2 of 21 客户确认反馈 Feedback of customer’s Confirmation 经确认，我方承认该规格书 We accept the specification after Confirmed 客户名称 Customer name 客户签字 Customer signature 确认日期 Confirmation Date 请签字后将此页与首页按以下地址回传我公司，谢谢！ Please feed back this paper and first paper after your signature by the address,thanks! 地址：四川省绵阳市安州工业园区 ADD： Anzhou,Industrial park,Mianyang,Sichuan 公司：四川爱联科技有限公司 Factory： Sichuan iLink Technology Co.,Ltd. 批准 Approved 审核 Checked 拟制 Designed 产品 ProductWIFI 模组 WIFI MODULE 型号 Model WIFI-2-R812USA2 日期 Date 2017-8-18
WIFI-2-R812USA2 Dual Band 11ac USB WiFi Module with RTL8812AU 四川爱联科技有限公司 Sichuan iLink Technology Co.,Ltd. page 3 of 21 更改记录 Record of Modification 序号 No 更改日期 Date of modification 主要更改内容 Main content of modification 更改原因 Reason of modification 更改通知编号 Serial number of modification 确认 Confirm 1 2016-5-27 初版 覃达开 2 2016-6-30 1、刷新产品图片 标签更改为高温 覃达开 3 2016-9-15 1、刷新产品图片 刷新标签格式 覃达开 4 2017-2-6 1、刷新产品包装 1、增加真空要求 2、删除外箱图案 覃达开 5 2017-8-12 1、 更改标签 2、 刷新标签二维码格式 1、产品增加认证号2、提高识别率 覃达开 6 2017-8-18 增加 FCC NOTE 产品进行 FCC 认证 覃达开
WIFI-2-R812USA2 Dual Band 11ac USB WiFi Module with RTL8812AU 四川爱联科技有限公司 Sichuan iLink Technology Co.,Ltd. page 4 of 21 1. Introduction WIFI-2-R812USA2 is based on realtek RTL8812AU, is a WLAN 11ac Dual Band module, which fully supports the features and functional compliance of IEEE 802.11 a/b/g/n/ac standards. This documentation describes the engineering requirements specification. 1.1 RF module Overview The general HW architecture for the module is shown in Figure 1. This WLAN Module design is based on Realtek RTL8812AU. It is a highly integrated single-chip MIMO(Multiple In Multiple Out) Wireless LAN (WLAN) USB2.0 network interface controller complying with the 802.11ac specification. It combines a MAC, a 2T2R capable baseband, and RF in a single chip. The RTL8812AU provides a complete solution for a high throughput performance wireless client. Figure 1 Module Block Diagram 1.2 Specification reference This specification is based on additional references listed below. _ IEEE Std. 802.11a _ IEEE Std. 802.11b _ IEEE Std. 802.11g _ IEEE Std. 802.11n _ IEEE Std. 802.11ac
WIFI-2-R812USA2 Dual Band 11ac USB WiFi Module with RTL8812AU 四川爱联科技有限公司 Sichuan iLink Technology Co.,Ltd. page 5 of 21 1.3 System Functions Table1: General Specification as below: Main Chipset Realtek RTL8812AU-VS Operating Frequency 2.4GHz & 5GHz Wi-Fi Standard 802.11a/b/g/n/ac Modulation 11b: DBPSK, DQPSK and CCK and DSSS 11a/g: BPSK, QPSK, 16QAM, 64QAM and OFDM 11n: BPSK, QPSK, 16QAM, 64QAM and OFDM 11ac: BPSK, QPSK, 16QAM, 64QAM, 256QAM and OFDM Data rates up to 867Mbps Host Interface USB2.0 PCB Stack 4-layers design Dimension Typical，27.00mm x 17.80mm x 3.7mm Operation Temperature 0℃ to +60℃ Storage Temperature -25℃ to +85℃ Operation Voltage 3.3V +/-10%
WIFI-2-R812USA2 Dual Band 11ac USB WiFi Module with RTL8812AU 四川爱联科技有限公司 Sichuan iLink Technology Co.,Ltd. page 6 of 21 2. Mechanical Specification 2.1 Mechanical Outline Drawing Typical Dimension ( L x W x H): 27.00 x17.8 x3.7mm NOTE1:General tolerance ±0.15mm unless otherwise stated 2.2Pin definition Pin # Name Pin # Name Pin # Name 1 PDN 6 LED 11 ANT1 2 VDD(3.3V) 7 GND 12 GND 3 DM- 8 ANT0 4 DP+ 9 GND 13 NC 5 GND 10 GND 14 NC
WIFI-2-R812USA2 Dual Band 11ac USB WiFi Module with RTL8812AU 四川爱联科技有限公司 Sichuan iLink Technology Co.,Ltd. page 7 of 21 3. Electrical Specification This Specification is based-on conductive DVT testing result. The extreme condition include overall temperature (0℃,+25℃,+60℃) and overall voltage (3.0V,3.3V,3.6V). 3.1 IEEE 802.11a Section: Items Contents Specification IEEE802.11a Mode OFDM Channel CH36 to CH165 Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps TX Characteristics Min. Typ. Max. Unit Remark1. Power Levels 1) 13dBm Target (For Each antenna port) 11 13 15 dBm 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz - - -20 dBr 2) at fc +/-20MHz - - -28 dBr 3) at fc > +/-30MHz - - -40 dBr 3. Constellation Error(EVM) @ Target Power 1) 6Mbps - - -5 dB 2) 9Mbps - - -8 dB 3) 12Mbps - - -10 dB 4) 18Mbps - - -13 dB 5) 24Mbps - - -16 dB 6) 36Mbps - - -19 dB 7) 48Mbps - - -22 dB 8) 54Mbps - -30 -25 dB 4. Frequency Error -20 20 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) 1) 6Mbps (PER ≦10%) - -85 -82 dBm 2) 9Mbps (PER ≦10%) - -84 -81 dBm 3) 12Mbps (PER ≦10%) - -82 -79 dBm 4) 18Mbps (PER ≦10%) - -80 -77 dBm 5) 24Mbps (PER ≦10%) - -77 -74 dBm 6) 36Mbps (PER ≦10%) - -73 -70 dBm 7) 48Mbps (PER ≦10%) - -69 -66 dBm 8) 54Mbps (PER ≦10%) - -68 -65 dBm 6. Maximum Input Level (PER ≦10%) -30 - - dBm
WIFI-2-R812USA2 Dual Band 11ac USB WiFi Module with RTL8812AU 四川爱联科技有限公司 Sichuan iLink Technology Co.,Ltd. page 8 of 21 3.2 IEEE 802.11b Section: Items Contents Specification IEEE802.11b Mode DSSS / CCK Channel CH1 to CH13 Data rate 1, 2, 5.5, 11Mbps TX Characteristics Min. Typ. Max. Unit Remark1. Power Levels 1) 17dBm Target (For Each antenna port) 15 17 19 dBm 2. Spectrum Mask @ Target Power 1) fc +/-11MHz to +/-22MHz - - -30 dBr 2) fc > +/-22MHz - - -50 dBr 3. Constellation Error(EVM) @ Target Power 1) 1Mbps - - -10 dB 2) 2Mbps - - -10 dB 3) 5.5Mbps - - -10 dB 4) 11Mbps - -20 -10 dB 4. Frequency Error -20 - 20 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) 1) 1Mbps (FER ≦8%) - -83 -76 dBm 2) 2Mbps (FER ≦8%) - -80 -76 dBm 3) 5.5Mbps (FER ≦8%) - -79 -76 dBm 4) 11Mbps (FER ≦8%) - -76 -76 dBm 6. Maximum Input Level (FER ≦8%) -10 - - dBm
WIFI-2-R812USA2 Dual Band 11ac USB WiFi Module with RTL8812AU 四川爱联科技有限公司 Sichuan iLink Technology Co.,Ltd. page 9 of 21 3.3 IEEE 802.11g Section: Items Contents Specification IEEE802.11g Mode OFDM Channel CH1 to CH13 Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps TX Characteristics Min. Typ. Max. Unit Remark2. Power Levels 1) 15dBm Target (For Each antenna port) 13 15 17 dBm 3. Spectrum Mask @ Target Power 1) at fc +/-11MHz - - -20 dBr 2) at fc +/-20MHz - - -28 dBr 3) at fc > +/-30MHz - - -40 dBr 4. Constellation Error(EVM) @ Target Power 1) 6Mbps - - -5 dB 2) 9Mbps - - -8 dB 3) 12Mbps - - -10 dB 4) 18Mbps - - -13 dB 5) 24Mbps - - -16 dB 6) 36Mbps - - -19 dB 7) 48Mbps - - -22 dB 8) 54Mbps - -30 -25 dB 5. Frequency Error -20 - 20 ppm RX Characteristics Min. Typ. Max. Unit 6 Minimum Input Level Sensitivity(each chain) 1) 6Mbps (PER ≦10%) - -85 -80 dBm 2) 9Mbps (PER ≦10%) - -84 -79 dBm 3) 12Mbps (PER ≦10%) - -82 -77 dBm 4) 18Mbps (PER ≦10%) - -80 -75 dBm 5) 24Mbps (PER ≦10%) - -77 -72 dBm 6) 36Mbps (PER ≦10%) - -73 -68 dBm 7) 48Mbps (PER ≦10%) - -69 -64 dBm 8) 54Mbps (PER ≦10%) - -68 -63 dBm 6. Maximum Input Level (PER ≦10%) -20 - - dBm
WIFI-2-R812USA2 Dual Band 11ac USB WiFi Module with RTL8812AU 四川爱联科技有限公司 Sichuan iLink Technology Co.,Ltd. page 10 of 21 3.4 IEEE 802.11n HT20 (2.4G) Section: Items Contents Specification IEEE802.11n HT20 @ 2.4GHz Mode OFDM Channel CH1 to CH13 Data rate (MCS index) MCS0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/15 TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels 1) 14dBm Target (For Each antenna port) 12 14 16 dBm 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz - - -20 dBr 2) at fc +/-20MHz - - -28 dBr 3) at fc > +/-30MHz - - -45 dBr 3. Constellation Error(EVM) @ Target Power 1) MCS0 - - -5 dB 2) MCS1 - - -10 dB 3) MCS2 - - -13 dB 4) MCS3 - - -16 dB 5) MCS4 - - -19 dB 6) MCS5 - - -22 dB 7) MCS6 - - -25 dB 8) MCS7 - -31 -28 dB 4. Frequency Error -20 - 20 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) 1) MCS0 (PER ≦10%) - -85 -82 dBm 2) MCS1 (PER ≦10%) - -84 -79 dBm 3) MCS2 (PER ≦10%) - -82 -77 dBm 4) MCS3 (PER ≦10%) - -80 -74 dBm 5) MCS4 (PER ≦10%) - -76 -70 dBm 6) MCS5 (PER ≦10%) - -72 -66 dBm 7) MCS6 (PER ≦10%) - -70 -65 dBm 8) MCS7 (PER ≦10%) - -69 -64 dBm 6. Maximum Input Level (PER ≦10%) -20 - - dBm
WIFI-2-R812USA2 Dual Band 11ac USB WiFi Module with RTL8812AU 四川爱联科技有限公司 Sichuan iLink Technology Co.,Ltd. page 11 of 21 3.5 IEEE 802.11n HT20 (5G) Section: Items Contents Specification IEEE802.11n HT20 @ 5GHz Mode OFDM Channel CH36 to CH165 Data rate (MCS index) MCS0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/15 TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels 1) 12dBm Target (For Each antenna port) 10 12 14 dBm 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz - - -20 dBr 2) at fc +/-20MHz - - -28 dBr 3) at fc > +/-30MHz - - -45 dBr 3. Constellation Error(EVM) @ Target Power 1) MCS0 - - -5 dB 2) MCS1 - - -10 dB 3) MCS2 - - -13 dB 4) MCS3 - - -16 dB 5) MCS4 - - -19 dB 6) MCS5 - - -22 dB 7) MCS6 - - -25 dB 8) MCS7 - -31 -28 dB 4. Frequency Error -20 - 20 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) 1) MCS0 (PER ≦10%) - -85 -82 dBm 2) MCS1 (PER ≦10%) - -84 -79 dBm 3) MCS2 (PER ≦10%) - -82 -77 dBm 4) MCS3 (PER ≦10%) - -80 -74 dBm 5) MCS4 (PER ≦10%) - -76 -70 dBm 6) MCS5 (PER ≦10%) - -72 -66 dBm 7) MCS6 (PER ≦10%) - -70 -65 dBm 8) MCS7 (PER ≦10%) - -69 -64 dBm 6. Maximum Input Level (PER ≦10%) -30 - - dBm
WIFI-2-R812USA2 Dual Band 11ac USB WiFi Module with RTL8812AU 四川爱联科技有限公司 Sichuan iLink Technology Co.,Ltd. page 12 of 21 3.6 IEEE 802.11n HT40 (2.4G) Section: Items Contents Specification IEEE802.11n HT40 @ 2.4GHz Mode OFDM Channel CH3 to CH11 Data rate (MCS index) MCS0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/15 TX Characteristics Min. Typ. Max. Unit Remark1. Power Levels 1) 14dBm Target (For Each antenna port) 12 14 16 dBm 2. Spectrum Mask @ Target Power 1) at fc +/-21MHz - - -20 dBr 2) at fc +/-40MHz - - -28 dBr 3) at fc > +/-60MHz - - -45 dBr 3. Constellation Error(EVM) @ Target Power 1) MCS0 - - -5 dB 2) MCS1 - - -10 dB 3) MCS2 - - -13 dB 4) MCS3 - - -16 dB 5) MCS4 - - -19 dB 6) MCS5 - - -22 dB 7) MCS6 - - -25 dB 8) MCS7 - -31 -28 dB 4. Frequency Error -20 - 20 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) 1) MCS0 (PER ≦10%) -85 -79 dBm 2) MCS1 (PER ≦10%) -82 -76 dBm 3) MCS2 (PER ≦10%) -79 -74 dBm 4) MCS3 (PER ≦10%) -77 -71 dBm 5) MCS4 (PER ≦10%) -72 -67 dBm 6) MCS5 (PER ≦10%) -69 -63 dBm 7) MCS6 (PER ≦10%) -68 -62 dBm 8) MCS7 (PER ≦10%) - -66 -61 dBm 6. Maximum Input Level(PER ≦10%) -20 - - dBm
WIFI-2-R812USA2 Dual Band 11ac USB WiFi Module with RTL8812AU 四川爱联科技有限公司 Sichuan iLink Technology Co.,Ltd. page 13 of 21 3.7 IEEE 802.11n HT40 (5G) Section: Items Contents Specification IEEE802.11n HT40 @ 5GHz Mode OFDM Channel CH38 to CH163 Data rate (MCS index) MCS0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/15 TX Characteristics Min. Typ. Max. Unit Remark1. Power Levels 1) 12dBm Target (For Each antenna port) 10 12 14 dBm 2. Spectrum Mask @ Target Power 1) at fc +/-21MHz - - -20 dBr 2) at fc +/-40MHz - - -28 dBr 3) at fc > +/-60MHz - - -45 dBr 3. Constellation Error(EVM) @ Target Power 1) MCS0 - - -5 dB 2) MCS1 - - -10 dB 3) MCS2 - - -13 dB 4) MCS3 - - -16 dB 5) MCS4 - - -19 dB 6) MCS5 - - -22 dB 7) MCS6 - - -25 dB 8) MCS7 - -31 -28 dB 4. Frequency Error -20 - 20 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) 1) MCS0 (PER ≦10%) -85 -79 dBm 2) MCS1 (PER ≦10%) -82 -76 dBm 3) MCS2 (PER ≦10%) -79 -74 dBm 4) MCS3 (PER ≦10%) -77 -71 dBm 5) MCS4 (PER ≦10%) -72 -67 dBm 6) MCS5 (PER ≦10%) -69 -63 dBm 7) MCS6 (PER ≦10%) -68 -62 dBm 8) MCS7 (PER ≦10%) - -66 -61 dBm 6. Maximum Input Level(PER ≦10%) -30 - - dBm
WIFI-2-R812USA2 Dual Band 11ac USB WiFi Module with RTL8812AU 四川爱联科技有限公司 Sichuan iLink Technology Co.,Ltd. page 14 of 21 3.8 IEEE 802.11ac HT20 Section: Items Contents Specification IEEE802.11ac HT20 @ 5GHz Mode OFDM Channel CH36 to CH165 Data rate (MCS index) Nss1 MCS0/1/2/3/4/5/6/7/8 Nss2 MCS0/1/2/3/4/5/6/7/8 TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels 1) 11dBm Target (For Each antenna port) 9 11 13 dBm mcs8 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz - - -20 dBr 2) at fc +/-20MHz - - -28 dBr 3) at fc > +/-30MHz - - -40 dBr 3. Constellation Error(EVM) @ Target Power 1) Nss1 MCS0 - - -5 dB 2) Nss1 MCS1 - - -10 dB 3) Nss1 MCS2 - - -13 dB 4) Nss1 MCS3 - - -16 dB 5) Nss1 MCS4 - - -19 dB 6) Nss1 MCS5 - - -22 dB 7) Nss1 MCS6 - - -25 dB 8) Nss1 MCS7 - - -27 dB 9) Nss1 MCS8 - -34 -30 dB 4. Frequency Error -20 - 20 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) 1) Nss1 MCS0 (PER ≦10%) - -85 -82 dBm 2) Nss1 MCS1 (PER ≦10%) - -82 -79 dBm 3) Nss1 MCS2 (PER ≦10%) - -80 -77 dBm 4) Nss1 MCS3 (PER ≦10%) - -77 -74 dBm 5) Nss1 MCS4 (PER ≦10%) - -73 -70 dBm 6) Nss1 MCS5 (PER ≦10%) - -69 -66 dBm 7) Nss1 MCS6 (PER ≦10%) - -68 -65 dBm 8) Nss1 MCS7 (PER ≦10%) - -67 -64 dBm 9) Nss1 MCS8 (PER ≦10%) -62 -59 dBm 6. Maximum Input Level (PER ≦10%) -30 - - dBm
WIFI-2-R812USA2 Dual Band 11ac USB WiFi Module with RTL8812AU 四川爱联科技有限公司 Sichuan iLink Technology Co.,Ltd. page 15 of 21 3.9 IEEE 802.11ac HT40 Section: Items Contents Specification IEEE802.11ac HT40 @ 5GHz Mode OFDM Channel CH38 to CH159 Data rate (MCS index) Nss1 MCS0/1/2/3/4/5/6/7/8/9 Nss2 MCS0/1/2/3/4/5/6/7/8/9 TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels 1) 10dBm Target (For Each antenna port) 8 10 12 dBm mcs9 2. Spectrum Mask @ Target Power 1) at fc +/-21MHz - - -20 dBr 2) at fc +/-40MHz - - -28 dBr 3) at fc > +/-60MHz - - -40 dBr 3. Constellation Error(EVM) @ Target Power 1) Nss1 MCS0 - - -5 dB 2) Nss1 MCS1 - - -10 dB 3) Nss1 MCS2 - - -13 dB 4) Nss1 MCS3 - - -16 dB 5) Nss1 MCS4 - - -19 dB 6) Nss1 MCS5 - - -22 dB 7) Nss1 MCS6 - - -25 dB 8) Nss1 MCS7 - - -27 dB 9) Nss1 MCS8 - - -30 dB 10) Nss1 MCS9 - -35 -32 dB 4. Frequency Error -20 - 20 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) 1) Nss1 MCS0 - -82 -79 dBm 2) Nss1 MCS1 - -79 -76 dBm 3) Nss1 MCS2 - -77 -74 dBm 4) Nss1 MCS3 - -74 -71 dBm 5) Nss1 MCS4 - -70 -67 dBm 6) Nss1 MCS5 - -66 -63 dBm 7) Nss1 MCS6 - -65 -62 dBm 8) Nss1 MCS7 - -64 -61 dBm 9) Nss1 MCS8 - -59 -56 dBm 10) Nss1 MCS9 - -57 -54 dBm 6. Maximum Input Level (PER ≦10%) -30 - - dBm
WIFI-2-R812USA2 Dual Band 11ac USB WiFi Module with RTL8812AU 四川爱联科技有限公司 Sichuan iLink Technology Co.,Ltd. page 16 of 21 3.10 IEEE 802.11ac HT80 Section: Items Contents Specification IEEE802.11ac HT80 @ 5GHz Mode OFDM Channel CH42 to CH155 Data rate (MCS index) Nss1 MCS0/1/2/3/4/5/6/7/8/9 Nss2 MCS0/1/2/3/4/5/6/7/8/9 TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels 1) 10dBm Target (For Each antenna port) 8 10 12 dBm mcs9 2. Spectrum Mask @ Target Power 1) at fc +/-41MHz - - -20 dBr 2) at fc +/-80MHz - - -28 dBr 3) at fc > +/-120MHz - - -40 dBr 3. Constellation Error(EVM) @ Target Power 1) Nss1 MCS0 - - -5 dB 2) Nss1 MCS1 - - -10 dB 3) Nss1 MCS2 - - -13 dB 4) Nss1 MCS3 - - -16 dB 5) Nss1 MCS4 - - -19 dB 6) Nss1 MCS5 - - -22 dB 7) Nss1 MCS6 - - -25 dB 8) Nss1 MCS7 - - -27 dB 9) Nss1 MCS8 - - -30 dB 10) Nss1 MCS9 - -35 -32 dB 4. Frequency Error -20 - 20 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) 1) Nss1 MCS0 - -79 -76 dBm 2) Nss1 MCS1 - -76 -73 dBm 3) Nss1 MCS2 - -74 -71 dBm 4) Nss1 MCS3 - -71 -68 dBm 5) Nss1 MCS4 - -67 -64 dBm 6) Nss1 MCS5 - -63 -60 dBm 7) Nss1 MCS6 - -62 -59 dBm 8) Nss1 MCS7 - -61 -58 dBm 9) Nss1 MCS8 - -56 -53 dBm 10) Nss1 MCS9 - -54 -51 dBm 6. Maximum Input Level (PER ≦10%) -30 - - dBm 4 Software Requirements The driver supports the following operating systems: Linux and Win OS.
WIFI-2-R812USA2 Dual Band 11ac USB WiFi Module with RTL8812AU 四川爱联科技有限公司 Sichuan iLink Technology Co.,Ltd. page 17 of 21 5 Antenna matching The 8th&11th Pin connect to antenna, please refer to design demand a).模块和天线要求远离干扰源，模块地和天线地要求为一个整体。b).PIN8PIN11为WIFI模组的RF接口，与天线之间布线要求共面阻抗为50Ω，建议使用弧线和直线，长度尽可能短。c).L1,L2,C1组成π型匹配网络并靠近天线接口设计，具体根据天线推荐及排版设计的实测效果进行调整。
WIFI-2-R812USA2 Dual Band 11ac USB WiFi Module with RTL8812AU 四川爱联科技有限公司 Sichuan iLink Technology Co.,Ltd. page 18 of 21 6. Package Information
WIFI-2-R812USA2 Dual Band 11ac USB WiFi Module with RTL8812AU 四川爱联科技有限公司 Sichuan iLink Technology Co.,Ltd. page 19 of 21 7、Refelow Standard Condition 升 温 区：温度：<150℃，时间：60～90 秒之间, 斜率控制在 1～3℃/S 之间。 预热恒温区：温度：150℃～200℃，时间：60-120 秒之间，斜率在 0.3-0.8 之间。 回流焊接区：峰值温度 235℃~250℃(建议峰值温度＜245℃），时间 30-70 秒。 冷 却 区：温度：217℃~170℃，斜率在 3～5℃/S 之间。 焊料为锡银铜合金无铅焊料/ Sn&Ag&Cu Lead-free solder(SAC305)。 注意：产品可承受极限温度 255 度5秒，为保证产品质量，回流曲线应该在保证焊点质量时不损害 PCB 和元器件之间寻求平衡，并在以上曲线区间内进行为宜.
WIFI-2-R812USA2 Dual Band 11ac USB WiFi Module with RTL8812AU 四川爱联科技有限公司 Sichuan iLink Technology Co.,Ltd. page 20 of 21 8、Product Picture TOP VIEW BOTTOM VIEW Detail 备注：图片仅供参考，背面字符中供应商标示、批次号等信息会稍有不同。
WIFI-2-R812USA2 Dual Band 11ac USB WiFi Module with RTL8812AU 四川爱联科技有限公司 Sichuan iLink Technology Co.,Ltd. page 21 of 21 FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‐ Reorient or relocate the receiving antenna. ‐ Reorient or relocate the receiving antenna. ‐ Reorient or relocate the receiving antenna. ‐Consult the dealer or an experienced radio/TV technician for help important announcement Important Note:Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/Canada. This device is intended only for OEM integrators under the following conditions: 1. The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2. The transmitter module may not be co-located with any other transmitter or antenna, Important Note: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Any company of the host device which install this modular with limit modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C:15.247 and 15.209 requirement, Only if the test result comply with FCC part 15.247 and 15.209 requirement, then the host can be sold legally. End Product Labeling If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: 2AFG6-R812USA2. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. When the module is installed inside another device, the user manual of this device must contain below warning statements; 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product.Custom design antennas may be used, however the OEM installer must following the FCC 15.21 requirements and verify if new FCC approval will be necessary.

Navigation menu