Gobiz Electronics G711 Two way car alarm system - remote unit User Manual PISCISPLUS B52 Manual for FCC

Gobiz Electronics Ltd. Two way car alarm system - remote unit PISCISPLUS B52 Manual for FCC

Users Manual

Table of contentsFunction button instructionsDescription of the icons on the remote LCD screenBasic FunctionSound & Light ArmingMute ArmingDisarming2.Emergency A lert3.Stop A lert4.Emergency Disarming5.Alarming MemoryRemind Arming Reminder & Automatic Armingutomatic back to arming mode(avoid mistaken disarming).3. Close Door ReminderCentral Control Door Lock AutomationThe Selection Of Dynamo Electronic / Pneumatic Lock6.Open Doors and Parking Light Flash SelectionAutomatic Closing Window Selection. Auto-arming On/ Off10. Remote Vibration On /Off11.Remo te Button Lock 12.Turn On Remote Back Light 13 The Busy Tone Reminder Of Remote ...............15.Remote Battery Low Reminder16. Remote Turn On / Off Engine and Air-condition (Optional Feature) settingTechnical ParameterTroubleshooting Special reminder 12Attention to the use of the remote .......... 12..........................................................................................1....................................................2....................................................................................................................31. ...................................................................................................32. ....................................................................................................................33. .......................................................................................................................34.Remote Trunk Release....................................................................................................35.Sound & Light Searching Car.........................................................................................36.Anti-hijacking mode...........................................................................................................4Alarming Function............................................................................................................51.Shock Alert........................................................................................................................5................................................................................................................5...........................................................................................................................5.......................................................................................................5..............................................................................................................5Additional Function..........................................................................................................61. ..............................................................62.A .........................................6......................................................................................................64. ............................................................................65. ...................................................6.............................................................7 7. .............................................................................78. Door Positive / Negative Trigger Selection .......................................................................7 9 ........................................................................................................7.................................................................................................7...................................................................................................8.........................................................................................8.Signal Indication...........................................................................................................814. ...........................................................8...................................................................................8.............................8Parameter ...............................................................................................................9Remote code learning & deleting..................................................................................10........................................................................................................10.....................................................................................................11...................................................................................................................................................................................
Function Button Instructions1Arming Button Ø After vehicle is parked, press button shortly to lock the door and enter into sound & light arming mode; Ø During the driving, press button shortly to lock the door; Ø Hold to press button for 2 seconds, the remote buttons will be locked.Disarming Button Ø Press button shortly to disarm the system, door will be unlocked Ø During the driving, press button shortly to unlock the door. Mute arming Ø After vehicle is parked, press button shortly, door will be locked and enter into mute arming mode; Ø After vehicle is parked, press button for 2 seconds, remote engine start and air-condition on; Ø During the driving, press button for 2 seconds, enter into anti-hijack mode.Car finding Ø Press button shortly, enter into sound & light searching car mode; Ø Press button for 2 seconds, enter into light flash searching car mode. + Trunk open Ø Press + button for 2 seconds simultaneously, trunk will be opened ØPress + button shortly simultaneously, remote back light will be illumined. + Setting mode Ø Press + button for 1 second simultaneously, enter into setting mode. + Vibration function setting shortcut button Ø Press + button for 1 second simultaneously, remote control vibration function turn on/off. + Auto rearming function setting shortcut button Ø Press + button for 1 second simultaneously, auto rearming function turned on/off.
Trunk openedLEDBatttery lifeMute Arming ArmingShock AlertDisarmingAuto rearmingDoor openedParking lightsEngine startedVibrationClockAlarm clock Signal IndicationUnlock/lock buttonSETSETSetting mode 2Description of the icons on the remote LCD screenFCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following Changes or modifications not expressly approved by the party responsible for two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. compliance could void the user's authority to operate the equipment.
1 Sound & Light ArminghAfter parked the vehicle and closed the door properly, press button shortly, door will be locked automatically, main unit siren will beep once, the parking lights will flash once and status indicator LED will be flashing, Remote responds a sound and illumines back light simultaneously. Icon and will appear, icon will flash once, icon will be flashing on the remote LCD screen, system enter into sound and light arming mode, at the same time, remote will show the corresponding vehicle information.2 Mute Arming hAfter parked the vehicle and closed the door properly, press button shortly, door will be locked automatically, the parking lights will flash once and status indicator LED will be flashing, Remote responds a sound and illumines back light simultaneously. Icon and will appear, icon will flash once, icon will be flashing on the remote LCD screen, system enter into mute arming mode, at the same time, remote will show the corresponding vehicle information.3 Disarming hPress button shortly in arming mode, door will be unlocked, main unit siren will beep twice(the siren will not respond in the mute arming mode), parking lights will flash twice, LED off, the system is disarmed. Remote responds a sound, icon will appear, icon will disappear, icon will flash twice on the remote LCD screen.4 Remote Trunk ReleasehAfter parked the vehicle, press + button over 2 seconds, trunk will be unlocked (this function only for the vehicle had been installed motor of trunk release) remote responds a sound and illumines back light simultaneously. Icon will flash for 5 seconds on the remote LCD screen to indicate the trunk is already opened. 5 Sound & Light Searching CarhAfter stopped engine and parked the vehicle :Press button shortly, siren will sound for 15 seconds and parking lights will flash simultaneously, press any button could stop this function.Press button over 2 seconds, parking lights will flash for 15 seconds to find vehicle by light, press any button could stop flash.Basic Function3
6 Anti-hijacking modehThis function will protect your vehicle in the event that there is an attempt to Hi-jack the vehicle. Alternative Remote Anti-hijack or Auto Anti-hijack is available by programming, when user need Remote Anti-hijack function, please select jumper JP5 in the main unit which is in the position of Remote Anti-hijack (details in the main unit installation guide); when user need Auto Anti-hijack function, please select jumper JP5 in the main unit which is in the position of Auto Anti-hijack (details in the main unit installation guide). While trigger anti-hijack mode, parking lights will flash once and the LED will flash quickly to show the system is entering anti-hijacking mode. 1). Remote Anti-hijack:If user select this mode, Turn ignition to ON position in disarming status, press button for 3 seconds, the parking lights will flash once and the LED will flash quickly to show the system is entering anti-hijack mode. Exit: Within 15 seconds after enter this mode, press button or press reset switch for 1 seconds, LED will OFF to confirm exit this anti-hijacking mode; If pass 15 seconds, press reset switch for 1 seconds, parking lights flash once,siren chirps once and LED will OFF to confirm exit this anti-hijacking mode. 2). Auto Anti-hijack: If user select this mode,Turn ignition to ON position or when driving the car, if the door is forced to open, the system will activate anti-hijack immediately. The parking lights will flash once and the LED will flash quickly to show the system is entering anti -hijack mode. EXIT: Within 15 seconds after enter this mode, press button or press reset switch for 1 seconds, LED will OFF to confirm exit this anti-hijacking mode; If pass 15 seconds, press reset switch for 1 seconds, parking lights flash once, siren chirps once and LED will OFF to confirm exit this anti car-jacking mode. hWhen the system enter into anti-hijacking:From beginning to 15 secnods, LED flash quickly, 16seconds, LED flash slowly, from 45 seonds to 75 seconds, parking lights flash and siren chirps intermittently, after 75 seconds, parking lights flashing and siren keeps chirping, the engine will be disabled after 90 seconds.Basic Function40sec.TimerEngine stopperSiren chirpLights flashLED flashLED flash quicklyOne flashLED flash slowlyParking lights flashing twice per secondSiren chirps intermittentlySiren keeps chirpingEngine stopper15sec. 45sec. 75sec. 90sec.
1 Shock AlerthDuring arming mode, if your vehicle’s shock sensor is triggered at first time, siren will beep 5 times (siren has not respond in mute arming mode), parking lights will flash 5 times simultaneously, this time the vehicle can’t start, remote will send out Bi...Bisound 5 times and vibrate twice, illumine back light simultaneously. Icon & will be flashing on the remote LCD screen.hWhen the vehicle is triggered by second time within 15 seconds, main unit siren keep long beep for 30 seconds, parking lights flash , vehicle can not start. Remote will send out shock alarming sound and vibrate, back light turn on, icon & will flash on the remote LCD screen.hDuring mute arming mode if your vehicle’s shock sensor is triggered , main unit siren will not sound, only parking lights flash, remote alarm responds the same as sound & light arming’s.2 Emergency AlerthDuring arming mode, if door/trunk is opened, step the foot brake or turn the ignition key to ON position, main unit siren will alarm for 30 seconds, parking lights will flash, this time the vehicle can’t start-up. Remote send out emergency alarming music for 30 seconds and vibrate, back light flash. Icon Flash.hDuring emergency alarming, if the main unit has detected that shock sensor is triggered, the remote LCD screen shall show the corresponding shock alarm icon simultaneously.3 Stop AlerthDuring arming mode, if you need to cancel alarming, press one of or button will stop the alert, the system will return to the previous arming status.4 Emergency disarminghProvided the remote is lost, damaged accidently, if user needs to disarm the vehicle, two method as follows:1. Open the door by the car key and keep the door opening, the siren chirps at this moment, step the foot brake and insert the key, turn ACC from OFF to ON 10 times, the last time should keep ON position over 2 seconds, vehicle is disarmed. This time, only press button to disarm the status or it will auto disarm this status after learn code to the new remote.2. Open the door by the car key and keep the door opening, the siren chirps at this moment, then turn ACC to ON position, step the foot brake and then press the reset switch for 3 times continuously, vehicle is disarmed. This time, only press button to disarm the status or it will auto disarm this status after learn code to the new remote.5 Alarming MemoryhIf the vehicle has been triggered and alarmed in arming mode, when you disarm the system and open the door, it sounds the voices:1). If the shock sensor has been triggered , main unit siren will beep twice.2). If the door, trunk, foot brake and ACC have been triggered, main unit siren will beep 4 times.5Alarming Function
1 Remind Arming Reminder & Automatic ArminghAfter turned off the engine and closed the door, if the owner did not set alarm within 10 seconds, the parking lights will flash simultaneously to remind owner to set alarm. hAfter owner get off the vehicle for 20 seconds without setting alarm, the main unit will notify the remote on which the back lights will turn on and sound with the remind arming chord at the same time , icon will flash 5 seconds on the remote LCD screen to remind the owner to arm the system.hProvided owner still leave the vehicle without setting alarm after 1 minutes, if the auto-arming functions were turned on and the alarming system might transfer into the situation of mute alarming automatically, remote back light will flash and send out a long chord, meanwhile icon will appeared on the LCD screen, icon flash 5 seconds then turn into icon to remind owner the door is still unlocked.2 Automatic back to arming mode(avoid mistaken disarming )hbutton turn on with setting the alarming system, icon will display on the LCD screen.hAfter armed the system, if door or trunk are not closed, the main unit siren will beep 3 times, and parking lights flash simultaneously. Remote back light will turn on, vibrate and sound Bi-Bi twice, icon or on the LCD screen will flash to remind owner to close the door. If owner leave the door opening after 15 seconds, the main unit siren will chirp and remote alerts.hIf owner continue driving and leaving the door opened after 15 seconds, and step foot brake, the parking lights flash twice, if leave the door open after 15 seconds, the main unit will remind one more time only.hWhen closed door, and continue driving for 15 seconds and step on the foot brake, the door will be locked; then when turn off the engine, door lock will unlocked, press button door lock will be locked when you are driving, and press button door will be unlocked.hWhen select the jumper JP1 in the main unit which is in the position of dynamo electronic lock (details in the main unit installation guide), press remote or button, the time for locking or unlocking is less, when the vehicle is using dynamo electronic lock may apply this mode.hWhen select the jumper JP1 in the main unit which is in the position of pneumatic lock (details in the main unit installation guide), press remote or button, the time for locking or unlocking is longer, when the car is using pneumatic lock may apply this mode, it needs to select when installing the car alarm system.When in the arming mode, press would disarm the system, if the door is not opened within 25 seconds, the arming system might taken as mistaken disarming and back to the arming status automatically. Remote back light will and send out a respond chord which is the same3 Closing door reminder4 Central Control Door Lock Automation5 The Selection of Dynamo Electronic/ Pneumatic lockNotice: this product has been set as dynamo electronic lock before leave the factory.6Additional Function
6 Open Door and Parking Light Flash SelectionNotice: this product has been set as before leave the factory.7 Automatic Closing Window SelectionAttention: this function is suitable for the vehicle which have the Auto closing window function, it can close the windows with the key turn in a twisting or spinning way, such as Passat, Bora, Golf and so on, if the condition is not available and do not try to operate this function ,otherwise it would made some damage to the central control lock.Notice: this product has been set as without automatic closing window before leave the factory.8 Door Positive /Negative Trigger SelectionNotice: this product has been set as before leave the factory, you can select according to the type of the automobiles.9 Auto-arming On/OffNotice: the auto arming function for this product has been turned on before leave the factory.10 Remote Vibration On/OffhWhen select the jumper JP2 in the main unit which is in the position of open door and parking light flash (details in the main unit installation guide), while you open the door, the parking lights flash 15 seconds at once to remind the cars behind.hWhen select the jumper JP2 in the main unit which is in the position of open door and parking light OFF (details in the main unit installation guide). While you open the doors, the parking lights shall not flash.hopen door and parking light flashhAfter enter into arming mode then operate this function, the alarm system could control the auto window machine to close the window. When need auto-closing window function, select jumper JP3 in the main unit which is in the position of Automatic closing window (details in the main unit installation guide), it could operate this function successfully when you are setting the arming system; select jumper JP3 in the main unit which is in the position of Without automatic closing window (details in the main unit installation guide), this function has been cancelled. hWhen select the jumper JP4 in the main unit which is in the position of Door negative trigger (details in the main unit installation guide),it is in the door negative trigger mode.hWhen select the jumper JP4 in the main unit which is in the position of Door positive trigger (details in the main unit installation guide),it is in the door positive trigger mode.Door negative triggerhWhen disabled the engine starter, hold to press + button for 1 second simultaneity, main unit siren chirp 5 times and the parking lights flash simultaneously, it means the auto arming function has been turned on, the icon shows on the LCD screen, you can terminate this operation with the same way, the siren chirps 3 times and parking light flash simultaneously, icon will disappear from the LCD screen. Repeat this operation, the auto arming function shall switch between on and off. hhHold to press + button for 1 second, icon disappear from the remote LCD screen which shows the vibration function has been turned off; you can turn it on in the same way, the icon shows on the LCD screen and remote vibrates twice at this time.7Additional Function
11 Remote Button Lock12 Turn On Remote Back Light Notice: You can continue operating this function after locked the button.13 Signal Indication 14 The Busy Tone Reminder of Remote uch as the main unit is sending the signal to the remote which will sound busy tone means this channel has been occupied(about 3 seconds), please try this operation later. 15 Remote Battery Low Reminder 16 Remote Turn On/Off the Engine & Air-condition (Optional Feature)Notice: when the door is opened. ACC is turned to ON position or even step the foot brake, all could not turn on the engine effectively .Notice: Before remote starts the engine, owner have to make sure that the car is in neutral and parking brake(you may fail if without pulling parking brake), otherwise it might incur danger. If you would like to switch on the air-condition with remote control, make sure the air-condition was turned on after the last parking, otherwise you may fail to fulfill this operation. After remote engine started, engine will be off after 15 minutes. In this period, if the vehicle has foot brake or ignition key turned, the engine will be off immediately.hHold to press button for 2 seconds, remote will sound Bi-Bi , icon OFF in the right corner of the LCD shows remote has been locked, press button 2 seconds again to release button lock, and the remote sound Bi-Bi-Bi , you can see ON in the right corner. Only you can press button to release button lock or press + button to turn on the back light in button lock status, other buttons will not be function. In the operation when the clock display changed to OFF and flash 6 times, to remind remote button lock on, and then will change to display clock again.hHold to press + button at the same time, the remote back light will be on for 3seconds, it is convenient to check the time in the night.hIf the remote fail to receive the signal of the main unit in 2.5 minutes, the signal strength indication icon on the LCD will disappear, only the antenna icon shows that the remote has go beyond the service range; after remote control has return to the service scope within 2 minutes, the signal strength indication icon on the LCD will display again, which reminds that the remote is in the service scope.hWhen manipulate the remote provided encounter a problem s hWhen the remote is battery low, when pressing any buttons will sound Bi-Bi 5 times to remind battery low. When icon flash, you should exchange the battery in time.hTurn on: hold to press button for 2 seconds , the remote will receive the respond music, engine has been turned on, then icon rotates on the LCD screen.hTurn off: press button or button could turn off the engine and enter into the arming status.hTurn on/off air-condition: after the engine was turned on successfully, perform the same operation to turn on/off the air-condition; when switch on the air-condition, starter icon on the LCD screen will flash speedily; when switch off the air-condition, icon turn into rotate.8Additional Function
hHold to press + button for 1 second, remote will sound a remind tone, back light will be turned on, icon SET flash and enter into setting mode.hThen press button,it will circulate exchange and select among time/minutetime/hour (alarm clock)ON/OFF (alarm clock)/minute (alarm clock)/hour (vibration)ON/OFF (auto-arming)ON/OFF EXIT, the corresponding icon will flash with icon SET simultaneously.hPress button you can set the corresponding parameter of the flashing icon, ON means turn on the function, OFF means turn off the function. After set the present parameter, press button to select next one and perform the same operation, when you are setting the time and alarm clock’s parameters, hold to press button parameters shall change speedily.hDuring the course of setting the parameters, hold to press + button for 1 second any time, icon SET and EXIT flash simultaneously, you can save the parameters and the present status you have set and exit from the operation, the remote control send out a remind tone meanwhile.hWhen you press button select item to icon EXIT , hold to press + button for 1 second at the same time, you can save the parameters and the present status you have set and exit from the operation, press button you can exit from the present operation directly and without saving the modifications.hWhen reached the alarm clock time you have set, remote control will sends out Bi-Bi remind tone and vibrates, icon flash at one time for 30 seconds. press any key could stop the alarm clock.Reminder:About setting vibrate function ON/OFF, auto-arming function ON/OFF . The user could via parameter setting, also could via double button operation to set quickly according to additional function description.9Parameter Setting
Remote code learninghWhen the vehicle is not in the alarming mode, hold to press the Learning button on the main unit, the main unit siren sounds Du 1 time, and the parking lights flash once simultaneously, the LED indicator light on, then you can press any key on the remote once, the remote sounds respond chord music 3 times after you have finished it successfully, the main unit siren sounds Du3 times, and parking lights flashes 3 times. Pay attention not to release the Learning button , continue pressing any key from the 2nd to the 4th on the remote once and to learn, LED off indicates the learning code was finished. Method two:hWhen in disarming mode, step the foot brake, turning the key from OFF ON 8 times, leave the key from OFF ON and maintain ON when it is the 8th times, the main unit siren sounds Du once and the parking lights flash once simultaneously, LED indicator light on, then you can press any key on the remote once, the remote control beeps 3 times with the respond chord music, the main unit siren sounds Du 3 times, and the parking lights flash 3 times. Attention do not release the foot brake, continue pressing any key from the 2nd to the 4th on the remote control once and to learn, LED off indicates the learning code was finished. hHold to press Learning button on the main unit, LED indicator light of the main unit will be off after 10 seconds, the siren voices out a long tone, and the parking lights keep on once indicates the remote which code had been learnt has been deleted.Method one:Remote code deleting:10Remote code learning & deletingTechnical parameterMAIN UNIT:Working voltage 12V 3VQuiescent current 10mAWorking frequency 433.92MHzSiren sound level 110~125dBWorking temperature -20 ~+85REMOTE CONTROLWorking voltage 1.1V 1.5V Quiescent current 0.1mAWorking frequency 433.92MHzTransmitting power 10mWWorking temperature -20 ~+60
Problem Solution1.The continuous beeps of the siren can not be stopped by the remote control after the installation of the main unit.2.After disarming the system, parking lights do not flash or after set the arming, it does not alarm when open doors by force.3.After set the sound & light arming, it alarms if with slight touch or when the heavy vehicle passes by .Check the door switch pin in stalled in a correct way; Check whether the sensitivity of the door switch is cut or in disconnection.This phenomenon caused by highly sensitivity of the shock sensor, adjust the knob for regulating the sensitivity of the shock sensor to reduce the sensitivity, if you fail to solve it then change a sensor. The plug is improperly inserted or not; The line is improperly connected or not; The fuse of the main unit is broken or not;The codes of the remote control and the main unit are identical or not.4.Remote control set arming system successfully, but failed to the central lock. Check whether the wiring of the central control lock has been destroyed, cut or in short circuit: the installation of the wiring is in a correct way;Check whether the wiring fuse of the central control lock has been cut, if you can see the wire has been burned, which shows the mistakes in installation, please recheck the connection wire;Plese reread the central control lock installation manual and the wiring installation manual in details. 5.The vehicle could not operate with remote or it is still in ignition mode after started successfully.The manual brake checking line hasn't connecting properly; The engine oil lamp checking line haven't connecting properly.Troubleshooting11
hThe system could realize the maximum distance for wireless sending and receiving between remote control and vehicle, and show the vehicle situation clearly, but it will affected by the factor of building, geographical environments or weather condition, The radio wave propagation might be hampered, and affect the sending and receiving distances.hBefore the installation, please make sure that whether the car you are desired to install is in dynamo electronic mode or pneumatic mode, and you also have to confirm the type of trigger, and set the correct jumper line position on the main unit (this product has set in a dynamo electronic position mode before leaves the factory), and standard the operation, wiring, installation stringently which in accordance with the automobiles technical standard of the country. Please have the experiential and skilled technician whom hold the automobiles electrician qualified certificate installed .hThe remote is precision electronic product. Don't make it broken and soggy.hThe system is intended mainly to alarming, intimidating the robbery, increasing the stealing difficulty and reminding the owner. Owner have to still keep your alert.hThe user manual has covered all the detailed information which the owner need to know, suggesting you read the manual in details before you install or use the product.hDo not break it heavily or put it in a moist circumstance, do not touch the screen of the liquid surface with your hands. hDo not try to disassembly or maintain it, forbid using the remote when you are on the air-craft.hAvoiding keep close to the high-frequency electric waves or place it in a circumstance in which the temperature is above 60 degrees.hWhen the remote is in power shortage time, please exchange the battery.hWhen use the remote in the car which have pasted the explosion-proof membrane, the remote control’s distance might be affected to some extent.Attention to the Use of the Remote Special reminder12
Central Lock Installation DiagramA WIRE OF CENTRAL LOCK LockUnlockWhite/BlackYellow/BlackOrange/BlackYellowOrangeWhiteWhite/BlackWhite/BlackWhite/BlackWhite/BlackWhite/BlackYellow/BlackYellow/BlackYellow/BlackYellow/BlackYellow/BlackOrange/BlackOrange/BlackOrange/BlackOrange/BlackOrange/BlackYellowYellowYellowYellowYellowOrangeOrangeOrangeOrangeOrangeWhiteWhiteWhiteWhiteWhiteNC COM NO NC COM NO B -PULSES""LOCKGROUNDUNLOCKGROUND"COLORS1 GREEN/BLUE2 BROWN3 RED/BLUEGroundCentral Lock+12VELECTRIC VACUUM PUMP123PS THE WIRE1 CHANGE THE POLARITYC VACUUM PUMP TYPEFOR MERCEDES. BENZ.AND.AUDI.ETCE +/-PULSES OUTPUTGROUND+12VGROUND+12V+12VCENTRAL LOCKF CARS EQUIPPED WITH CENTRAL LOCKLOCKUNLOCKACTUATORACTUATOR""D +12V PULSESLOCK+12VUNLOCK+12VCentral Lock Installation GuideThis system can control several common central locks without any other additional parts.Type A :For vehicles equipped with central lock, first recommendation. (FIG. B)Type B :For vehicles equipped with central lock but no motor on driver's side, add a master motor and rod into the driver side door. (FIG. E)This type of installation is applicable to vehicles equipped with factory central lock unit such as some Ford, Mitsubishi, Mazda,and Nissan models.INSTALLATION NOTICE : First, install the actuator near the door's manual latch, and then fix the rod of the actuator on themanual latch.Type C : For vehicles equipped with central lock and with motor on driver's side. (FIG.D)Type D : For vehicles equipped with electrical-activated vacuum-pump controlled door locks. (FIG. C) The timing of actuator mechanism can be set as shorter(dynamo electronic lock) or longer(pneumatic lock).This type of installation is applicable for some Mercedes-Benz and Audi models.Type E : For some GM vehicles equipped with factory central lock unit.(FIG. F)For some vehicles not mentioned above, please consult professional installers.NOTE: Type B installation method (FIG. E) is suitable for most vehicles.Warning :1. Please ask the experienced automobile electrician to install this product.2. The connection wires avoid the high temperature, the high- Pressured nstallation. 3.The broken wiring place must insulate wraps up .Main Unit InstallationThe main unit is placed under the vehicle control panel. Afterfixing the main unit in a suitable place, start connecting all the wiring according to the Wire Connection Diagram. Before putting back all the parts, simply test system functions first.Sensitivity adjustment of shock sensorIt is recommended to mount the shock sensor under the dashboard and stick it closely to inner wall of car body without any shock pad.Please remember the place where the shock sensor is mounted. It will cause false alarm if it is too sensitive, or it will miss alarm, if it is too insensitive. The sensitivity of shock sensor can be adjusted moderately according to the environment and user’s demand to make it work availably.Antenna PositionThe ideal position for the antenna is in the top corner of the front windscreen right up of the wheel side. Please keep the antenna free from any obstructions to prevent reception interference.NOTICE: If the vehicle is parked in urban area with many buildings around,or under a strong electric field environment, the receiving and dispatching distance will be affected.Dynamo electronic lockJP1Pneumatic lockOpen door and parking light flashJP2Open door and parking light OFFWithout automatic closing windowJP3Automatic closing windowDoor negative triggerRemote Anti-hijackDoor positive trigger Auto Anti-hijack JP4JP5Remark: When partial vehicle types enable the engine starter, Not only the third gear to start the ignition wire and output +12V, but also the another wire to output +12V simultaneously. Thus, the yellow wire of engine starter relay should connect with it. Partial vehicle types there are two air condition control wires, just connecting the black wire and the brown wire of the air condition relay separately, do not connect the black wire to +12V. The majority of vehicle types connect the black wire with +12V, the brown one connect with the air condition control wire of the lock.Yellow/BlackRed/Black +Trunk releaseBlue Door pin switchWhite/BlackOrange/BlackYellowWhiteOrange12V VDDCar BatteryFUSE 10AFUSE 10AFUSE 20ALEDReset switchSwitchOil pump+12V/Air-conditioner control wireAir-conditioner controlIgnitionEngine startBlack Start motor Yellow Engine stopperGray IgnitionPurple Air conditionerHand brake inputBluePurpleRedHand brake inputDetecting of engine starterRed Green Detecting of engine starter+12VShock sensorRed/VDDSirenFoot brake switchFoot brake lightOrangeYellow no connectingWhiteONACCSTREngine cut off+12VPinkBlack/Ground12P4P6P2PLearning button3P2PPISCIS PLUSBrownBrown Parking light Parking lightOil lightBrake light Oil light switchAntennaACC+12VOnSTRBrownBrownWhiteYellowYellowGreenGreenCentral Door Lock ConnectorMain UnitDefault factory setting:VDynamo electronic lockJumperVOpen door and parking light flashVWithout automatic closing windowVV Door negative trigger Remote Anti-hijackMax Min6PRemote engine starter moduleTWO WAY VEHICLE SECURITYTWO WAY VEHICLE SECURITYTWO WAY VEHICLE SECURITYTWO WAY VEHICLE SECURITY ALARM SYSTEM ALARM SYSTEM ALARM SYSTEM ALARM SYSTEMMain Unit Installation GuideMain Unit Installation GuideMain Unit Installation GuideMain Unit Installation Guide

Navigation menu