Go Networks MBW-510F-000 WIRELESS LAN ACCESS POINT User Manual GO MBW 510 Installation Guide

Go Networks Inc. WIRELESS LAN ACCESS POINT GO MBW 510 Installation Guide

manual

GO MBW 510 Installation Guide Document # 0510-30-000-A02 Nov 15, 2007
GO MBW 510 Installation Guide Trademarks and Licensing Agreement © 2007 GO Networks, Inc. All rights reserved. All information contained in this document is protected by international copyright treaties. No information may be copied or reproduced without the express written consent of GO Networks Inc. GO Metro Broadband Wireless, GO MBW, WLAN Sector Base Station, WLS, GO WLAN Pico Base Station, WLP, GO Wireless Network Controller, and WNC are all trademarks of GO Networks Inc. Any duplication, transmission by any method, or storage in an information retrieval system of any part of this publication for other purposes other than those stated above is strictly prohibited without the specific written permission of GO Networks, Inc. This includes, but is not limited to, transcription into any form of computer system for audio, text, print, or visual retrieval. All rights under federal copyright laws and international laws will be strictly enforced. All other trademarks and registered trademarks are the property of their respective owners. GO Networks Inc. 1943 Landings Drive • Mountain View, CA 94043 • USA Tel +1.650.962.2000 • Fax +1.650.962.2010 Email support@gonetworks.com
GO MBW 510 Installation Guide The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency when using its antennas. Any changes or modifications not expressly approved by GO Networks could void the user's authority to operate the equipment. FCC Compliance Status The following information is for FCC compliance: This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment, this equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference. However, there is no guarantee that interference will not occur. To meet regulatory restrictions, the outdoor access point must be professionally installed. The antennas used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
GO MBW 510 Installation Guide Table of Contents Introduction........................................................................................................................................1 Key Product Features ................................................................................................................................1 Organization of this Document...................................................................................................................2 GO MBW 510 Femto Cellular-Mesh Wi-Fi Base Station .................................................................3 MBW 510 Package Components.................................................................................................................3 MBW 510 Safety Information.......................................................................................................................3 RF Exposure..............................................................................................................................................3 MBW 510 Lightning Protector....................................................................................................................4 Information de sécurité pour MBW 510......................................................................................................5 Exposition aux fréquences RF...................................................................................................................5 Paratonnerre pour MBW 510....................................................................................................................5 Installation..........................................................................................................................................6 Installation Process......................................................................................................................................6 Site Survey ................................................................................................................................................6 Assembling and Mounting...........................................................................................................................7 Mounting Brackets.....................................................................................................................................9 Mounting the MBW 510 ...........................................................................................................................11 Mounting the Antenna..............................................................................................................................12 Cable Connections.....................................................................................................................................14 Cable Installation Tools ...........................................................................................................................15 Grounding Cable......................................................................................................................................15 Ethernet Connection................................................................................................................................16 Power Connection ...................................................................................................................................17 Computer Connection..............................................................................................................................18 Power Up and Software Configuration.....................................................................................................19 Appendix A: List of Acronyms........................................................................................................20 Appendix B: Wiring Specifications.................................................................................................22
- Page 1 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved. Introduction GO Networks MBW (Mobile Broadband Wireless) 500 series complements GO Networks MBW 2000 series and 1000 series products by offering femto cell Wi-Fi coverage. This product is ideal for providing fill-in coverage in conjunction with micro and pico level coverage that the MBW 2000 series and MBW 1000 series offer. The MBW 500 series comprises the MBW 510 Femto Cellular-Mesh Wi-Fi Base Station with an omni-directional, multi-radio, weather-proof design. This design has been optimized for streetlight or utility pole Wi-Fi applications. The MBW 510 is equipped with one 802.11b/g access radio for femto cell access and coverage with a separate 802.11a radio for high-performance mesh networking. Together with the MBW 2000 series and/or MBW 1000 series, the GO Networks’ solutions provide a high-performing, cost-effective Wi-Fi solution. Key Product Features • • • • • • • Cost-effective femto cellular-mesh Wi-Fi base station Designed for simple, fast and economical deployment Dual-radio design o 802.11b/g access o 802.11a for mesh networking Multiple virtual APs with multiple BSSIDs Advanced automatic mesh Designed for streetlight, wall, or pole deployment Support for all standard security scheme
- Page 2 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved. Organization of this Document The GO MBW 510 Installation Guide for the Femto Cellular-Mesh Wi-Fi Base Station offers information and instructions for quickly installing and configuring the MBW 510. The instructions and information are presented in one volume as follows: Introduction Contains introductory information about the MBW 510. GO MBW 510 Presents a general description and overview of the MBW 510 including content and safety procedures. Installation Process Describes the installation process for the MBW 510. Appendix A Lists the acronyms that appear in the manual. Appendix B Details the wiring specifications.
- Page 3 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved. GO MBW 510 Femto Cellular-Mesh Wi-Fi Base Station MBW 510 Package Components The MBW 510 package items are listed in Table 1: DESCRIPTION REV QTY Poll/Wall Mounting Kit Assembly 1.0 1 Connectors Kit for MBW 510 Package 1.0 1 MBW 510 unit 1.0 1 MBW 510 Access Antenna 2.4GHz 4dBi Gain, Omni 1 802.11a 5Ghz 6dBi Omni Antenna (Backhaul) 1 Table 1: MBW 510 Package Contents Deployments of gateway devices connected by wire to an indoor switch/router would include installation of a lightning protector. A lightning protector is not supplied as part of the standard package. It can be ordered from GO Networks as an accessory. Specific installation may require different Power/Ethernet connections. See Cable Connections for more details. MBW 510 Safety Information RF Exposure The MBW 510, an outdoor access point, is compliant with the requirements set forth in CFR 47 section 1.1307, addressing RF Exposure from radio frequency devices as defined in OET Bulletin 65. The outdoor access point antennas should be installed to provide a separation distance of at least 3 feet (1 meter) from humans.
- Page 4 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved. MBW 510 Lightning Protector A lightning protector is required when the MBW 510 unit is installed in an outdoor location and the Ethernet cable connects to an indoor network device. The purpose of the lightning protection is to protect people and equipment located indoors from lightning that might strike the MBW 510 or its outdoor cables. Therefore, the lightning protector device should be installed indoors, as close as possible to the point where the cables enter the building. The lightning protector can also be installed outdoors, as long as the cables that go from the lightning protector to the indoors are well protected from lightning between the box and the building entrance. Verify that you have shared grounding. GO Networks offers a lightning protector that can be ordered separately.
- Page 5 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved. Information de sécurité pour MBW 510 Exposition aux fréquences RF Le point d’accès extérieur MBW 510 est compatible avec la norme CFR 47 section 1.1307 concernant l’exposition aux appareils émetteurs de fréquences radio RF définis par le Bulletin 65 de l’OET. Les antennes doivent être installées à une distance minimum d’un mètre de personnes humaines. Paratonnerre pour MBW 510 Un paratonnerre est nécessaire lorsque le point d’accès MBW 510 est installe à l’extérieur et lié à un network intérieur par un câble Ethernet. La fonction du paratonnerre est de protéger les personnes et équipement situés en intérieur des éclairs qui pourraient frapper le MBW 510 ou son câble extérieur. Par conséquent, le paratonnerre doit être installé en intérieur le plus près possible du point où le câble de liaison pénètre le bâtiment. Le paratonnerre peut aussi être installé en extérieur à la condition que les câbles a l’intérieur du bâtiment soient protégés des éclairs entre le point d‘accès et l’entrée du bâtiment Vérifier que la prise de terre est partagée. GO Networks met a disposition à la vente un paratonnerre.
- Page 6 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved. Installation Installation Process Installing the Femto Cellular-Mesh Wi-Fi Base Station involves the following steps: 1. 2. 3. 4. 5. 6. 7. Performing a Site Survey Assembling and Mounting Mounting the MBW 510 unit Connecting the Antennas Connecting the cables Powering up the unit and configuring the software Performing a Post-installation Testing Procedure to verify connectivity and operation Site Survey Most wireless LANs include many access points installed in various locations in an overlapping radio-cell pattern. It is important to carefully identify each access point’s position and the assignment of its radio channels. Therefore, a site survey becomes an essential first step before physically deploying the MBW 510. Installation of the access points requires a backhaul to interface the corporate network or Internet. This backhaul connection can be a mesh configuration, an Ethernet-wired connection, or a third-party solution. When using any method other then a wired connection, keep in mind the MBW 510 has to have a good reception on its backhaul side so it will not limit the access-channel performance. Conclude the site survey with a detailed plan of the MBW system deployment. The system deployment plan should include MBW 510 mounting points and the routes for the power and backhaul cables. Note: When mounting the MBW 510 on a pole (or wall mount), the pole should be able to support four times the weight of the MBW 510, as well as the wind loading created by the MBW 510. Since the mounting structure itself is a potential source of interference, the cell should be mounted with at least 4 feet of clearance between the antennas and the mounting structure.
Assembling and Mounting The universal mount is used to attach and secure the MBW 510 to a wall, a streetlight arm, or a variety of poles. The MBW 510 mounting consists of the following stages and should be performed in the following order: - Page 7 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved. 1. 2. 3. 4. 5. 6. Connect the MBW 510 unit to the brackets using the ‘L’ adaptor. Secure the mounting brackets to a streetlight arm, wall, or pole. Assemble the MBW 510 unit to the bracket. Ground the MBW 510 unit. Align the MBW 510 unit. Mount the Antenna to the MBW 510 unit. Table 2 lists the universal mount parts: Item No. Description Qty Picture A Wall/Poll Bracket 1 B Clamping Bracket 1 C MBW 510 ‘L’ Adapter Wall/Poll Mount 1 D Hex Bolt M8x70 2 E Hex Bolt M8 x25 1 F Hex Bolt M8x40 1 G Flat Washer M8 3
- Page 8 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved. Item No. Description Qty Picture H Spring Washer M8 4 I Nut M8 1 Table 2: Mounting Kit Part List Hardware and Connectors Installation Tools The following tools are required to mount the MBW 510 on a pole. Description Picture Combination Wrench (13 mm) 13 mm Level Table 3: Mounting Tools and Equipment Note: All hardware and tools used for assembling and mounting the MBW 510 are Metric. To assemble the ‘L’ adaptor [C] to the MBW 510 unit: Attach the ‘L’ adapter to the MBW 510 using an M8 x25 hex bolt [E], a spring washer [H], and a flat washer [G], as illustrated in Figure 1. •
L AdapterHex BoltFlat WasherSpring Washer Figure 1: Mount ‘L’ Assembly Mounting Brackets To secure the mounting brackets: 1. Select an optimal mounting location on the pole. Select the highest mounting location with minimal obstacles to the antennas for optimal performance. NOTE: When mounting the MBW 510 on a pole, it should be placed on a pole that can support four times the weight of the MBW 510, as well as the wind loading created by the MBW 510. 2. Installation of the mounting brackets to a streetlight arm or a pole differs according to the width of the pole, as illustrated in Figure 2. Narrow pole1"-1.75" Normal pole1.75"-3" Large pole,greater than 3" Figure 2: Pole Bracket Assembly - Page 9 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
- Page 10 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved. 3. For narrow poles (1”–1.75” diameter): a) Place the two brackets, [A] and [B], around the pole at the approximate height where you wish to place the unit. When placing the clamping bracket [B], the small notch side should be in contact with the pole. b) Use two M8x70 hex bolts [D] and spring washers, insert them through both brackets and tighten them around the pole so that the two brackets are securely fastened. 4. For normal poles (1.75”–3” diameter): a) Place the two brackets, [A] and [B], around the pole at the approximate height where you wish to place the unit. When placing the clamping bracket [B], the large notch side should be in contact with the pole. b) Use two M8x70 hex bolts [D] and spring washers [H], insert them through both brackets and tighten them around the pole so that the two brackets are securely fastened. 5. For poles larger than 3” in diameter: a) The wall/poll bracket [A] and two 0.5" (13mm) wide stainless steel hose clamps (not supplied with mounting kit) are used. The hose clamps must be the appropriate size to fit around the pole and bracket. b) Open the each hose clamp by rotating the screw on the clamp counterclockwise. There may be additional resistance just before the clamp is completely open. This is normal and you should continue rotating the screws until the clamps are open. c) Insert the band of each clamp through both slots and over the bracket [A]. d) Place the bracket [A] and hose clamps around the pole at the approximate height where you wish to place the unit. e) Close each clamp by reinserting the band under the screw and rotate the screw clockwise. f) Position the bracket in the appropriate location and tighten the clamps around the pole so that the bracket is securely fastened.
6. For wall mounting: a) Fasten the wall/poll bracket [A] to the wall using four 3/16” (5mm) bolts, as shown in Figure 3. Use the appropriate bolts and fasteners, which is dependent on the material of the wall. Wall-mounting bolts and fasteners are not supplied with the mounting kit. b) Place the wall/poll bracket [A] at the appropriate location where you wish to place the unit. Using the four holes at the corners of the bracket, mark the location where the fasteners need to be installed. c) Install the four fasteners in the wall. d) Insert the four bolts through the bracket and securely fasten the bracket to the wall. Wall Mounting Holes Figure 3: Bracket Wall Mounting Mounting the MBW 510 To mount the MBW 510 unit: 1. After assembling the brackets, mount the MBW 510 unit on to the bracket as shown in Figure 4. Use a flat washer [G], a spring washer [H] and a nut [I]. - Page 11 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
Flat WasherNutSpring WasherMBW 510 Figure 4: MBW 510 Unit Mounting 2. Once the MBW 510 unit is mounted, release the bolts slightly and align the MBW 510 unit horizontally using the level, as shown in Figure 5. When the unit is perfectly aligned, firmly close all bolts, applying 120 inch-lbs of torque. Figure 5: Aligning the MBW 510 Mounting the Antenna The MBW 510 includes two antennas. One Wi-Fi antenna is used for user access, which operate on the 2.4 GHz band, marked A2. One antenna is used for the mesh networking connections, which operate on the 5 GHz band, marked B2. - Page 12 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
To mount the antennas on the MBW 510: 1. Attach the 2.4 GHz band antenna to terminal A2 and screw the antenna into place by hand. Rotate the antenna at its metallic base. The antenna should rotate easily. Tighten the antenna by hand only. Do not apply excessive force by using any tool, as this may damage the unit. 2.4 GHzAntennasTerminal A2 Figure 6: 2.4 GHz Band Antennas Installation 2. Attach the 5 GHz band antenna to terminal B2. Tighten the antenna by hand at its metallic base. The antenna should rotate easily. Do not apply excessive force by using any tool, as this may damage the unit. 5GHzAntennasTerminalB2 Figure 7: 5 GHz Band Antennas Installation - Page 13 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
Cable Connections When the MBW 510 is properly aligned, the connecters are located at the bottom of the unit. Cable requirements are often unique to the location and deployment topology of each installation. As a result of this limitation, the Ethernet and grounding cables are not included in the installation kit. The following cables are required to install the MBW 510 unit and should be connected in the following order: - Page 14 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved. • • • Grounding Cable – Provides the necessary electrical safety functions. Ethernet Cable – Required only for MBW 510 units connected to a wired network. Power Cable – Supplies AC power to the MBW 510 unit. The supplied AC power cable is designed to connect directly to a photocell power adapter. Table 4 lists the MBW 510 Connectors Kit parts: Item No. Description Qty Picture A Solderless Ring Terminal 1 B Sealed RJ45 connector 1 Table 4: Mounting Kit Part List
Cable Installation Tools The following special tools are required to install and connect cables related to the MBW 510. Description Picture Slotted Screwdriver 1/8” (3mm) wide Terminal Crimp Tool RJ45 Crimp Tool HT-210A Volt Meter Table 5: Cable Installation Tools and Equipment Grounding Cable Connect a grounding wire to the grounding screw at the bottom of the MBW 510 unit. A 10 AWG grounding cable is required to ground the MBW 510 unit. Figure 8: Grounding Connection - Page 15 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
To ground the MBW 510 unit: 1. Crimp the solderless ring terminal [A] contained in the MBW 510 Connectors Kit to the grounding cable. 2. Attach the solderless ring terminal [A] to the bottom of the MBW 510 unit using the grounding screw. 3. Connect the other end of the grounding cable to a proper ground. Note: Connect the 10 AWG grounding cable before connecting any other cables. When removing the MBW 510, the grounding cable should be the last cable removed. Noter: Connecter la prise de terre 10 AWG avant de connecter tout autre câble. Pendant la désinstallation du MBW 510, la prise de terre doit être le dernier câble retiré. Ethernet Connection Ethernet connection is used for wired backhaul connection or an interface to a third party wireless backhaul solution. Use outdoor rated CAT5 shielded cables or better. The outer diameter of the Ethernet cable should be 4.8 – 7 mm. When using CAT5 shielded cables the cable can be up to 100 meters. Following is a diagram explaining how the Ethernet cable should be assembled prior to connecting it to the MBW 510 unit: Figure 9: Ethernet Cable Connector - Page 16 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
- Page 17 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved. Power Connection The MBW 510 unit can be connected to an AC power source by one of several methods. It can be connected directly to a power source or by using an adapter to connect to the streetlight photocell (photo-control). The MBW 510 unit can support input voltage of 100 to 240 VAC (50 to 60 Hz). Note: Connect the grounding cable before connecting any other cables. When removing the MBW 510, the grounding cable should be the last cable removed. Noter: Connecter la prise de terre 10 AWG avant de connecter tout autre câble. Pendant la désinstallation du MBW 510, la prise de terre doit être le dernier câble retiré. To connect the AC power to the MBW 510 via the streetlight photocell: 1. Check the input voltage to the streetlight photocell. The voltage must be between 100 to 240 VAC. If yes, continue with this procedure. Otherwise, use a different method for the power connection. 2. Remove the streetlight photocell. Turn the photocell counterclockwise and lift the photocell out of the socket. 3. Insert the Auxiliary Power Adapter in the socket of the photocell. Note that one prong is larger than the other two. Align the larger prong on the adapter with the larger slot in the socket. Insert the Auxiliary Power Adapter into the socket and rotate the adapter clockwise. 4. Insert the photocell into the Auxiliary Power Adapter. Align the larger prong on the photocell with the larger slot in the socket on top of the adapter. Insert the photocell into the socket and rotate the photocell clockwise. 5. Connect the Auxiliary Power Adapter cable to the power connector socket on the MBW 510. 6. After connecting the power, verify that the Power (PWR) LED is lit. 7. Check the photocell. Cover the photocell and verify that the streetlight operates.
Computer Connection Figure 10 illustrates the Ethernet cable connections used to connect the MBW 510 to a notebook computer. This connection is typically used for the initial configuration. For more information regarding the configuration, see the GO MBW Configuration Guide. For more information regarding the Ethernet cable, see Appendix B: Wiring Specifications. - Page 18 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved. Figure 10: Connect and Access the MBW 510 MBW 510 Consol Port: RJ45 Consol Port: RJ45 Notebook PC
- Page 19 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved. Power Up and Software Configuration The MBW 510 unit is normally mounted on a streetlight (pole or wall) where it is inconvenient to configure. Therefore, it is recommended that wireless communication be established to the unit prior to installation, so that the unit can later be configured and monitored from the ground. To verify communications when installing the MBW 510 unit, the Mesh-Gateways must be installed and powered up first. The LEDs on the MBW 510 unit indicate the status of communications between the MBW 510 unit and the network. See Table 6 for more information on the LED indicators. When powering up a Mesh-Node, the BH LED should be lit to verify that the MBW 510 unit’s wireless communication is connected. MBW 510 boot time is about 2.5 minutes. The BH LED indicator will light up after the boot is completed. LED Function PWR Green – There is power to the unit. Unlit – There is no power to the unit. ETH Green – When the LED is on, there is a communication connection. When the LED is flashing, traffic is flowing though the MBW 510 unit. Unlit – There is no communication connection. Table 6: MBW 510 LED Indicators
- Page 20 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved. Appendix A: List of Acronyms Acronym Explanation 802.11 A family of specifications related to wireless networking, including: 802.11a, 802.11b, and 802.11g. AP Access Point. The hub of a wireless network. Wireless clients connect to the access point, and traffic between two clients must travel through the access point. Access points are often abbreviated to AP BH Backhaul BSSID Broadcast Service Set Identifier CPE Customer Premises Equipment. DHCP Dynamic Host Configuration Protocol. A protocol which enables a server to automatically assign an IP address to clients so that the clients do not have to configure the IP addresses manually. EAP Extensible Authentication Protocol. A standard form of generic messaging used in 802.1X. ESSID EGOed Service Set Identifier MBW Mobile Broadband Wireless PMK Pairwise Master Key SSID Service Set Identifier, a set of characters that give a unique name to a WLAN. TKIP Temporal Key Integrity Protocol VLAN Virtual Local Access Network WDS Wireless Distribution System
- Page 21 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved. Acronym Explanation WEP Wired Equivalent Privacy. An encryption system created to prevent eavesdropping on wireless network traffic. WLP Pico Cellular-Mesh Wi-Fi Base Station (MBW 1100) WLS Micro Cellular-Mesh Wi-Fi Sector Base Station (MBW 2100) WMG Wireless Media Gateway of the GO Networks MBW solution. GO Media dedicated CPE. WNC Wireless Network Controller of the GO Networks MBW solution. WPA Wi-Fi Protected Access. A modern encryption system created to prevent eavesdropping on wireless network traffic. It is considered more secure than WEP. WPA-EAP WPA-Extensible Authentication Protocol WPA-PSK WPA-Pre-shared key
- Page 22 of 22 - All contents are Copyright © 2007 GO Networks, Inc. All rights reserved. Appendix B: Wiring Specifications RJ-45-to-RJ-45 Straight Cable Signal RJ-45 Pin RJ-45 Pin Tx + 1 1 Tx - 2 2 Rx + 3 3 No connection 4 4 No connection 5 5 Rx - 6 6 No connection 7 7 No connection 8 8 Table 7: Computer Port Signaling and Cabling with a RJ-45 Adapter for the MBW 510 Unit

Navigation menu