Gilbarco LFADV RFID Module User Manual 13 0074 Exhibit Cover

Gilbarco Inc. RFID Module 13 0074 Exhibit Cover

UserManual.wiki >

Gilbarco >

LFADV User Manual

Manual

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: N6SLFADV IC: 827B-LFADV FCC Rule Part: 15.209 IC Radio Standards Specification: RSS-210 ACS Report Number: 13-0073 Manufacturer: Gilbarco Inc. Model: LFADV Manual

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 1Table of Contents PreliminaryTable of Contents1 – Introduction 1TRIND Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1About TRIND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1How TRIND Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Related Documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3TRIND Kit Coverage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 – Important Safety Information 53 – Systems Overview 9Full Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Hand Held Only Tag System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114 – Major Hardware Components 13Card Cage Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13T20229-G1 Card Cage Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13T20229-G1 Card Cage Assembly Parts List 4- . . . . . . . . . . . 14T20606-G2 Card Cage Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 T20606-G2 Card Cage Assembly Parts List 4-. . . . . . . . . . . . .15T20606-G3 Card Cage Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15T20606-G3 Card Cage Assembly Parts List 4- . . . . . . . . . . . . .16T20606-G5 Card Cage Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16T20606-G5 Card Cage Assembly Parts List 4- . . . . . . . . . . . . .17Disassembly and Installation For MPD®-3 Units with SID Displays . . . .17Disassembly and Installation For All MPD-3 Units. . . . . . . . . . . . . . . . . .17AC EMI Line Filter Q10895 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Transformers R20600 and R20719 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Power Supply Boards T20138 and T20314 . . . . . . . . . . . . . . . . . . . . . . .18T20138 Power Supply Board. 4- . . . . . . . . . . . . . . . . . . . . . . . . .18T20314 Power Supply Board. 4- . . . . . . . . . . . . . . . . . . . . . . . . .19 Data Control Boards Q13563 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19UHF Receiver Board Q13564 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20Transmitter Board Q13579. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21Gateway Boards T20128, T20678 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22Card Cage Cable Harness T20662-G2 . . . . . . . . . . . . . . . . . . . . . . . . . .23Full System TRIND R20520-G1 Transmitter Cable . . . . . . . . . . . . . . . . .23Full System TRIND R20525-G1 RS-485 Communication Cable . . . . . . .24Full System TRIND R20763-GX Power Supply Cables . . . . . . . . . . . . . .24Hand-Held TRIND System M00507 Ribbon Cable . . . . . . . . . . . . . . . . .25Hand-Held TRIND System M01366 Power Cable . . . . . . . . . . . . . . . . . .25TRIND Overhead Antennas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26T20231 Mobil Overhead Antenna Assembly . . . . . . . . . . . . . . . . . . . . . .26 T20231 Mobil Overhead Antenna Assembly Parts List 4- . . . . .26T20231 Mobil Overhead Antenna Bracket Assemblies and Hardware for The Advantage Series 4-. . . . . . . . . . . . . . . . . . . .28

Table of ContentsPage 2 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryT20231 Mobil Overhead Antenna Bracket Assemblies and Hardware for the MPD-3 4- . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28T20632 Single-Loop Overhead Antenna Assembly . . . . . . . . . . . . . . . . 29T20632 Single-Loop Overhead Antenna Assembly Parts List (Domestic) 4- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30T20632 Single-Loop Overhead Antenna Assembly Parts List (International) 4-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31T20632 Single Loop Antenna Assembly Bracket Kits for The Advantage Series 4- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32T20632 Single Loop Antenna Assembly Bracket Kits for the MPD-3 Series 4-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32T20632 Single Loop Antenna Assembly Bracket Kit for the Encore Unit 4- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Ultra High Frequency Antenna Q13851-01 and Q13851-02. . . . . . . . . . 33Antenna Tuning Board T20579-GX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33TRIND Option Doors With Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34MPD-3 Bezel Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35T20616-G1 MPD-3 Bezel Assembly Parts List 4- . . . . . . . . . . . 35T20616-G2 MPD-3 Bezel Assembly Parts List 4- . . . . . . . . . . . 36T20251-G1 MPD-3 Bezel Assembly Parts List 4- . . . . . . . . . . . 37Advantage Wide Frame Option Door Assemblies. . . . . . . . . . . . . . . . . . 38T20228-G1 Advantage Wide Frame Option Door Assembly Parts List 4- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38T20613 Advantage Wide Frame Option Door Assembly Parts List 4- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Advantage Narrow Frame Option Door Assemblies . . . . . . . . . . . . . . . . 40T20614 Narrow Frame Option Door Assembly Parts List 4- . . . 40T20253-G1 Narrow Frame Option Door Assembly Parts List 4- 41Encore CIM Door Option Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Encore CIM Door Option Assembly Parts List 4- . . . . . . . . . . . . 42Eclipse Ovendoor Option Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Eclipse Ovendoor Option Assembly Parts List 4- . . . . . . . . . . . 43Light/Microreader PCB T20446-G1, T20601-GX, M01580A001, and M01580A002 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Light/Microreader PCB M01218A001 and M01218A002 . . . . . . . . . . . . 45Hand-Held Antenna PCB T20143-G1 . . . . . . . . . . . . . . . . . . . . . . . . . . . 46TRIND Antenna PCA T20524-G1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46System Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47M00878 Low/High Frequency Antenna Cable . . . . . . . . . . . . . . . . . . . . 47R20773 Power and Data Option Door Cable . . . . . . . . . . . . . . . . . . . . . 47R20437-G01 TRIND to CRIND Logic Cable (Advantage and MPD-3) . . 48M00515A002 TRIND to CRIND Logic Cable For Encore 500 and Eclipse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48M001804A001 TRIND to CRIND Logic Cable for Encore 300 . . . . . . . . 49R20580 and M00811A001 AC Power Cables. . . . . . . . . . . . . . . . . . . . . 49Full System Cable Connections on the Legacy Advantage Series Dispensers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Full System Cable Connections on the MPD-3 Dispensers . . . . . . . . . . 51Full System Cable Connections on The Advantage Series and MPD-3 Dispensers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Hand-Held System Cable Connections on The Advantage Series and MPD-3 Dispensers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Full System Cable Connections on Encore 500 Dispensers. . . . . . . . . . 54Hand-Held System Cable Connections on Encore 500 and Eclipse Dispensers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 3Table of Contents PreliminaryM00878A001 and M00878A002 Antenna Cable Pin-to-Pin Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56M00515A002 Ribbon Cable Pin-to-Pin Connections . . . . . . . . . . . . . . . .56R20509-G1 Antenna Cable, Low Frequency Pin-to-Pin Connections . . .56R20519-G1, -G2 and -G3 Light/Microreader Cables Pin-to-Pin Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57R20521-G1 and -G2 Interface Microreader Cables Pin-to-Pin Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57R20522-G1 Interface Hand Held Antenna Cable Pin-to-Pin Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57R20522-G2 Interface Hand Held Antenna Cable Pin-to-Pin Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57R20526 TI/RFID Dummy Load Transmitter Cable Pin-to-Pin Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57R20437-G01 TRIND to CRIND Logic Cable Pin-to-Pin Connections . . .58Advantage Option R20773-G2 TRIND Data and Power Cable Pin-to-Pin Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58Encore Option R20773-G2 TRIND Data and Power Cable Pin-to-Pin Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59T20662-G2 TRIND Card Cage Cable Harness Cable Pin-to-Pin Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .595 – System Accessories 61ASC TRIND Tool Kit K94577-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61Standalone Jumper Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61Standalone Jumper Cable R20602-G1 For LF/UHF Full System . . . . . .61Standalone Jumper Cable R20602-G2 For Enhanced Gateway . . . . . . .63Dummy Load Transmitter R20526 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64Co-Axial Cable Tool Q13628-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64Field Strength Sensor Board Q13626-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65Test Tags Q13630-01 and Q13630-02 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66Q13630-01 Hand-Held Test Tag 5-. . . . . . . . . . . . . . . . . . . . . . .66Q13630-02 Car-Mount Test Tag 5-. . . . . . . . . . . . . . . . . . . . . . .66Tuning Tool Q13631-01 and Q13631-02. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .676 – Procedures for Factory Installed TRIND 69Positioning Overhead Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .697 – Dispenser Set-Up 71Addressing Dither Sync Address for LF/UHF Full System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71Setting Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72Addressing the Gateway/Enhanced Gateway Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72CRIND Address Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74Preparation for Tuning Antennas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75Tuning Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75Tuning Single-Loop Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75Mobil Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .778 – Testing and Troubleshooting 79

Table of ContentsPage 4 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryStatus Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79T20128 Gateway Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79T20678 Enhanced Gateway Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80Q13563 Data Control Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81T20601/M01560 Light/Micro Reader Boards . . . . . . . . . . . . . . . . . . . . . 83Isolating TRIND from CRIND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Tag Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Car Mounted Test Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Hand Held Test Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85Alternative Testing Using Laptop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86Troubleshooting Printed Circuit Boards on the T20229-G1 Card Cage Assembly. . . . . . . . . . . . . . . . 87Light/Micro-Reader Board T20295-G1 . . . . . . . . . . . . . . . . . . . . . . . . . . 87Gateway PCB T20128-G1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88Transmitter PCB Q13579-01. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88Data Control Board Q13563-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89TI/RFID Power Supply T20138-G1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89Troubleshooting Flow Charts for the T20606 Card Cage System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90TRIND Troubleshooting Flow Chart (Sheet 1 of 4) . . . . . . . . . . . . . . . . . 90TRIND Troubleshooting Flow Chart (Sheet 2 of 4) . . . . . . . . . . . . . . . . . 91TRIND Troubleshooting Flow Chart (Sheet 3 of 4) . . . . . . . . . . . . . . . . . 92TRIND Troubleshooting Flow Chart (Sheet 4 of 4) . . . . . . . . . . . . . . . . . 93Field Problem Survey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 949 – Glossary Glossary-95Appendix A - Radio Frequency Identification Defined A-97Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-97What is RFID? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-99Wireless Communication and Air Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-100Data Transfer Rate and Bandwidth. . . . . . . . . . . . . . . . . . . . . . . . . . A-101Range and Power Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-102Transponders/Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-103Basic Features of an RFID Transponder . . . . . . . . . . . . . . . . . . . . . A-103Powering Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-104Data Carrying Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-104Data Read Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-105Data Programming Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-105Physical Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-105Costs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-106Reader/Interrogator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-106RF Transponder Programmers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-106RFID System Categories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-107Appendix B - Cable Block Diagrams and Interconnects B-109R20515 Cable Block Diagram, Revision F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-109R20516 Interconnect Diagrams, Sheet 1 of 3, Revision E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-110R20516 Interconnect Diagrams, Sheet 2 of 3, Revision C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-111R20516 Interconnect Diagrams, Sheet 3 of 3, Revision E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-112R20762 Cable Block Diagrams, Sheet 1 of 2, Revision J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-113R20762 Cable Block Diagrams, Sheet 2 of 2, Revision J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-114T20607 Interconnect Diagrams, Sheet 1 of 4, Revision H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-115T20607 Interconnection Diagrams, Sheet 2 of 4, Revision H. . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-116T20607 Interconnection Diagrams, Sheet 3 of 4, Revision H. . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-117

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 5Table of Contents PreliminaryT20607 Interconnection Diagrams, Sheet 4 of 4, Revision H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-118R20775 Cable Block Diagrams, Sheet 1 of 2, Revision D. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-119R20775 Cable Block Diagrams, Sheet 2 of 2, Revision D. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-120T20663 Interconnect Diagrams, Sheet 1 of 3, Revision C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-121T20663 Interconnection Diagrams, Sheet 2 of 3, Revision C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-122T20663 Interconnection Diagrams, Sheet 3 of 3, Revision C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-123

Table of ContentsPage 6 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013Preliminary This page is intentionally left blank.

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 1TRIND OverviewPreliminary1 – IntroductionTRIND OverviewThe TRIND system is similar to the technology successfully used by many toll ways. It uses an electronic system located in the pump or register to “talk” with a miniature radio-like device (a tag). Together, these electronic devices provide “cashless” access to gasoline, food and merchandise by charging purchases to a credit card, check card, or other account you already have. The TRIND system operates on a dedicated tag identification code. Your credit card or check card account numbers are not typically used with the tag signal system, which protects your account from unauthorized use. And if your tag is ever lost or stolen, your liability is limited to the amount set by your financial institution. The TRIND device is an option available as a retrofit kit or factory installed device for The Advantage® Series, MPD®-3, Eclipse®, and Encore™ lines of fuel dispensers. The device is connected to the CRIND® device via a Gateway or serial interface board. In this application, the TRIND device is a software slave to the CRIND and the associated Point Of Sale (POS) Controller/Host. This means that a properly working TRIND system will look for and read tags, but only when “told” to by the controller, through the CRIND application. About TRIND The TRIND devices are developed to utilize Texas Instruments Radio Frequency Identification (RFID) technology. These devices provide two-way communications between an interrogator system in the fuel dispenser and the consumer’s hand held or car mounted transponder tag. This two-way communication authorizes and records sales, eliminating the need for the consumer to engage in a cash or credit card transaction.

Page 2 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013How TRIND WorksPreliminaryHow TRIND WorksTRIND utilizes radio frequency (RF) waves to communicate with a customer’s transponder. Transmitters located on overhead assemblies transmit radio waves that serve as a “wake up” call. As a car mounted transponder or hand held transponder enters the transmitter’s effective read zone, the transponder is activated. The transponder then transmits a code which is received by the TRIND antennas mounted overhead or on the option doors.This transmitted code is communicated from the TRIND to the CRIND unit, and from there to the POS (point of sale). The POS system communicates with a host to obtain authorization.Car mounted transponders are activated when they are within six feet of the front of the dispenser perpendicular to front of dispenser. Hand held transponders, usually on a key chain, function when pointed at a target graphic on the option door. Two-way communication is indicated when the option door target graphic light comes on, whether by car mount or hand held transponder signal.Figure 1-1: Encore and Eclipse Target Graphic LocationEclipseTarget GraphicEncoreMPD-3Advantage Narrow Frame (36") Advantage Wide Frame (48")Target Graphic

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 3Related DocumentsPreliminaryRelated DocumentsDocument Number Title GOLD LibraryMDE-2530 Pump and Dispenser Installation Manual Advantage & Legacy ModelsMDE-2531 Start-up and Service Manual for The Advantage Series Service ManualMDE-2540 The Advantage, Legacy & MPD Series Owners Manual Advantage & Legacy ModelsMDE-2562 CRIND Service Manual CRIND and TRINDMDE-3425 CRIND Retrofit Kit and CRIND Kit Selection Guide CRIND and TRINDMDE-3591 TRIND Retrofits Kits C00011-002-XXXX CRIND and TRINDMDE-3801 TRIND Multi 1 Retrofits Kits Manual CRIND and TRINDMDE-3883 TRIND TIRIS C00011-005 Kit Installation Manual CRIND and TRINDMDE-3917 TRIND TIRIS Encore 500 Retrofit Kit Installation Manual CRIND and TRINDMDE-3920 Encore 300 & 500 TRIND Retrofit Kit Installation CRIND and TRINDMDE-4063 TRIND TIRIS Advantage and MPD-3 Retrofit Kit Installation ManualCRIND and TRINDMDE-4073 TRIND TIRIS C00011-006 Retrofit Kit Installation CRIND and TRINDPT-1728 The Advantage Illustrated Parts Manual Parts ManualPT-1736 The Advantage/MPD/CRIND Illustration Parts Manual Parts Manual TRIND Kit CoverageThe following table provides TRIND kit numbers and the relative system coverage that applies to each.Kit Number Product Coverage Frequencies Interface Type Tag SystemC00011-001 Advantage, MPD-3 LF/UHF T20229-G1 Card Cage Hand Held/Car MountedC00011-002 Advantage, MPD-3 LF/UHF (note 2) T20606-G2 Card Cage Hand Held/Car MountedC00011-005 Advantage, MPD-3 LF (note1) T20606-G3 Card Cage Hand HeldC00011-004 Encore 500 LF/UHF T20606-G2 Card Cage Hand Held/Car MountedC00011-006 Encore 500, Eclipse LF T20606-G3 Card Cage Hand HeldC00011-007 Advantage, MPD-3 LF/UHF (ETSI) (note 3) T20606-G5 Card Cage Hand Held/Car MountedC00011-008 Encore 500 LF/UHF (ETSI) T20606-G2 Card Cage Hand Held/Car MountedC00011-009 Advantage, MPD-3 LF/UHF T20606-G5 Card Cage Hand Held/Car MountedC00011-010 Advantage, MPD-3 LF/UHF T20606-G2 Card Cage Hand Held/Car MountedC00012-00X Advantage, MPD-3 HF (note 4) T20538-G1/G2 Card Cage Hand HeldNotes:1. LF = Low Frequency (134 kHz) send and receive for Hand Held Tags.2. LF/UHF = Low Frequency (134kHz) send, and Ultra High Frequency (902 MHz) receive for Car Tags. Low Frequency (134 kHz) for Hand Held Tags.3. LF/UHF (ETSI) = Low Frequency (134 kHz) send and Ultra High Frequency (868 MHz) receive for Car Tags. Low Frequency (134 kHz) for Hand Held Tags.4. HF = High Frequency (13.56 MHz) send and receive for Hand Held Tags.

Page 4 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013TRIND Kit CoveragePreliminaryThis page is intentionally left blank.

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 5Important Safety InformationPreliminary2 – Important Safety InformationNotes: 1) Save this Important Safety Information section in a readily accessible location. 2) Although DEF is non-flammable, Diesel is flammable. Therefore, for DEF cabinets that are attached to Diesel dispensers, follow all the notes in this section that pertain to flammable fuels.This section introduces the hazards and safety precautions associated with installing, inspecting, maintaining or servicing this product. Before performing any task on this product, read this safety information and the applicable sections in this manual, where additional hazards and safety precautions for your task will be found. Fire, explosion, electrical shock or pressure release could occur and cause death or serious injury, if these safe service procedures are not followed. Preliminary PrecautionsYou are working in a potentially dangerous environment of flammable fuels, vapors, and high voltage or pressures. Only trained or authorized individuals knowledgeable in the related procedures should install, inspect, maintain or service this equipment.Emergency Total Electrical Shut-OffThe first and most important information you must know is how to stop all fuel flow to the pump/dispenser and island. Locate the switch or circuit breakers that shut off all power to all fueling equipment, dispensing devices, and Submerged Turbine Pumps (STPs). The EMERGENCY STOP, ALL STOP, and PUMP STOP buttons at the cashier’s station WILL NOT shut off electrical power to the pump/dispenser. This means that even if you activate these stops, fuel may continue to flow uncontrolled. You must use the TOTAL ELECTRICAL SHUT-OFF in the case of an emergency and not the console’s ALL STOP and PUMP STOP or similar keys.!WARNING!Total Electrical Shut-Off Before AccessAny procedure that requires access to electrical components or the electronics of the dispenser requires total electrical shut off of that unit. Understand the function and location of this switch or circuit breaker before inspecting, installing, maintaining, or servicing Gilbarco equipment.Evacuating, Barricading and Shutting OffAny procedure that requires access to the pump/dispenser or STPs requires the following actions:• An evacuation of all unauthorized persons and vehicles from the work area • Use of safety tape, cones or barricades at the affected unit(s)• A total electrical shut-off of the affected unit(s)Read the ManualRead, understand and follow this manual and any other labels or related materials supplied with this equipment. If you do not understand a procedure, call a Gilbarco Authorized Service Contractor or call the Gilbarco Support Center at 1-800-800-7498. It is imperative to your safety and the safety of others to understand the procedures before beginning work.Follow the RegulationsApplicable information is available in National Fire Protection Association (NFPA) 30A; Code for Motor Fuel Dispensing Facilities and Repair Garages, NFPA 70; National Electrical Code (NEC), Occupational Safety and Health Administration (OSHA) regulations and federal, state, and local codes. All these regulations must be followed. Failure to install, inspect, maintain or service this equipment in accordance with these codes, regulations and standards may lead to legal citations with penalties or affect the safe use and operation of the equipment.Replacement PartsUse only genuine Gilbarco replacement parts and retrofit kits on your pump/dispenser. Using parts other than genuine Gilbarco replacement parts could create a safety hazard and violate local regulations.Safety Symbols and Warning WordsThis section provides important information about warning symbols and boxes.Alert Symbol This safety alert symbol is used in this manual and on warning labels to alert you to a precaution which must be followed to prevent potential personal safety hazards. Obey safety directives that follow this symbol to avoid possible injury or death.Signal WordsThese signal words used in this manual and on warning labels tell you the seriousness of particular safety hazards. The precautions below must be followed to prevent death, injury or damage to the equipment:DANGER: Alerts you to a hazard or unsafe practice which will result in death or serious injury.WARNING: Alerts you to a hazard or unsafe practice that could result in death or serious injury. CAUTION with Alert symbol: Designates a hazard or unsafe practice which may result in minor injury.CAUTION without Alert symbol: Designates a hazard or unsafe practice which may result in property or equipment damage.Working With Fuels and Electrical EnergyPrevent Explosions and FiresFuels and their vapors will explode or burn, if ignited. Spilled or leaking fuels cause vapors. Even filling customer tanks will cause potentially dangerous vapors in the vicinity of the dispenser or island.DEF is non-flammable. Therefore, explosion and fire safety warnings do not apply to DEF fluid lines.!!!

Page 6 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013Important Safety InformationPreliminaryNo Open FireOpen flames from matches, lighters, welding torches or other sources can ignite fuels and their vapors.No Sparks - No Smoking Sparks from starting vehicles, starting or using power tools, burning cigarettes, cigars or pipes can also ignite fuels and their vapors. Static electricity, including an electrostatic charge on your body, can cause a spark sufficient to ignite fuel vapors. Every time you get out of a vehicle, touch the metal of your vehicle, to discharge any electrostatic charge before you approach the dispenser island.Working AloneIt is highly recommended that someone who is capable of rendering first aid be present during servicing. Familiarize yourself with Cardiopulmonary Resuscitation (CPR) methods, if you work with or around high voltages. This information is available from the American Red Cross. Always advise the station personnel about where you will be working, and caution them not to activate power while you are working on the equipment. Use the OSHA Lockout/Tagout procedures. If you are not familiar with this requirement, refer to this information in the service manual and OSHA documentation.Working With Electricity SafelyEnsure that you use safe and established practices in working with electrical devices. Poorly wired devices may cause a fire, explosion or electrical shock. Ensure that grounding connections are properly made. Take care that sealing devices and compounds are in place. Ensure that you do not pinch wires when replacing covers. Follow OSHA Lockout/Tagout requirements. Station employees and service contractors need to understand and comply with this program completely to ensure safety while the equipment is down.Hazardous MaterialsSome materials present inside electronic enclosures may present a health hazard if not handled correctly. Ensure that you clean hands after handling equipment. Do not place any equipment in the mouth. The pump/dispenser contains a chemical known to the State of California to cause cancer.WARNING! The pump/dispenser contains a chemical known to the State of California to cause birth defects or other reproductive harm.WARNING!In an EmergencyInform Emergency PersonnelCompile the following information and inform emergency personnel:• Location of accident (for example, address, front/back of building, and so on)• Nature of accident (for example, possible heart attack, run over by car, burns, and so on)• Age of victim (for example, baby, teenager, middle-age, elderly)• Whether or not victim has received first aid (for example, stopped bleeding by pressure, and so on)• Whether or not a victim has vomited (for example, if swallowed or inhaled something, and so on)Gasoline/DEF ingested may cause unconsciousness and burns to internal organs. Do not induce vomiting. Keep airway open. Oxygen may be needed at scene. Seek medical advice immediately.DEF generates ammonia gas at higher temperatures. When opening enclosed panels, allow the unit to air out to avoid breathing vapors.If respiratory difficulties develop, move victim away from source of exposure and into fresh air. If symptoms persist, seek medical attention.WARNING!WARNING!Gasoline inhaled may cause unconsciousness and burns to lips, mouth and lungs.Keep airway open.Seek medical advice immediately.WARNING!Gasoline/DEF spilled in eyes may cause burns to eye tissue.Irrigate eyes with water for approximately 15 minutes.Seek medical advice immediately.WARNING!Gasoline/DEF spilled on skin may cause burns.Wash area thoroughly with clear water.Seek medical advice immediately.WARNING!DEF is mildly corrosive. Avoid contact with eyes, skin, and clothing. Ensure that eyewash stations and safety showers are close to the work location. Seek medical advice/recommended treatment if DEF spills into eyes.WARNING!IMPORTANT: Oxygen may be needed at scene if gasoline has been ingested or inhaled. Seek medical advice immediately.Lockout/TagoutLockout/Tagout covers servicing and maintenance of machines and equipment in which the unexpected energization or start-up of the machine(s) or equipment or release of stored energy could cause injury to employees or personnel. Lockout/Tagout applies to all mechanical, hydraulic, chemical, or other energy, but does not cover electrical hazards. Subpart S of 29 CFR Part 1910 - Electrical Hazards, 29 CFR Part 1910.333 containsspecific Lockout/Tagout provision for electrical hazards.

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 7Important Safety InformationPreliminaryHazards and ActionsWARNINGSpilled fuels, accidents involving pumps/dispensers, or uncontrolled fuel flow create a serious hazard.Fire or explosion may result, causing serious injury or death.Follow established emergency procedures.DEF is non-flammable. However it can create a slip hazard. Clean up spills promptly.!Collision of a Vehicle with Unit Fire at Island Fuel SpillThe following actions are recommended regarding these hazards:• Do not go near a fuel spill or allow anyone else in the area.• Use station EMERGENCY CUTOFF immediately. Turn off all system circuit breakers to the island(s).• Do not use console E-STOP, ALL STOP, and PUMP STOP to shut off power. These keys do not remove AC power and do not always stop product flow.• Take precautions to avoid igniting fuel. Do not allow starting of vehicles in the area. Do not allow open flames, smoking or power tools in the area.• Do not expose yourself to hazardous conditions such as fire, spilled fuel or exposed wiring.• Call emergency numbers.

Page 8 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013Important Safety InformationPreliminaryThis page is intentionally left blank.

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 9Full SystemsPreliminary3 – Systems OverviewFull SystemsThe Full System product is an option available as a retrofit kit or factory installed equipment on the Advantage, MPD-3 and Encore, and Eclipse lines of fuel dispensers. The TRIND device is connected to the CRIND via a gateway or serial interface board. In this application TRIND is a software slave to the CRIND and the associated POS controller/host. This means that a properly working TRIND system will look for and read tags, but only when told to by the controller, through the CRIND application. This system is to be installed in accordance with all Underwriter’s Laboratories (UL), Federal Communications Commission (FCC), federal, state and local regulations associated with it. The following illustrations depict the system component used in the Original, Advantage, MPD-3, and Encore full systems.Figure 3-1: Original Full System Block DiagramOverhead Antenna AssemblySide AT20231-G1LF Transmitter (134kHz IntentionalRadiator)Q13579-01Control DataUHF Receiver Module902 - 928 MHz115 VAC(FROM DispenserAC POWERDISTRIBUTION)RS-232 RS-232Gateway BoardT20128 SERIAL DATAto CRIND logic boards(Dispenser Electronics)J7 J8J4P187P250P18522VDC,5VDC, GND5VDC,GND22VDC,5VDC, GNDJ6J322VDC, 5VDC, GND22VDC, 5VDC, GNDJ5 J5J2A J2B JA JBLF TXUHF RX Overhead Antenna AssemblySide BT20231-G1UHF RXLF TXPOWER REGULATINGCircuit BoardT20138-G1P177P179P176P175P178Light Board Assembly(T20295, T20446)on Dispenser Bezel Face (Side A)P181P180,P182RS-232, DigitalControl and LightControl CircuitP180,P182P181RS-232, DigitalControl and LightControl CircuitWhen overhead antennas are not part ofthe product, Dummy Load R20526-G1plugs into JA and JB. J2A and J2B areleft unconnected.DATA CONTROL BOARDQ13563-01 or -0260VACPower SupplyR20600-G1AC Power EMC FilterQ10895-01Micro-ReaderQ13551-01(134 KHzIntentional)Micro-ReaderQ13551-01(134 KHzIntentional)T20143BezelAntennaR20522-G2CableT20143BezelAntennaR20522-G2CableLight Board Assembly(T20295, T20446)on Dispenser Bezel Face (Side B)RS-232LF TX/RXLF TX/RXRS-485

Page 10 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013Full SystemsPreliminaryFigure 3-2: Advantage Series Full System Block DiagramOverhead Antenna AssemblySide AT20231-G1LF Transmitter (134kHz IntentionalRadiator)Q13579-01Control DataUHF Receiver ModuleRI-RFM-HREA902 - 928 MHz115 VAC(FROM DispenserAC POWERDISTRIBUTION)RS-232RS-232Gateway BoardT20128SERIAL DATAto CRIND logic boards(Dispenser Electronics)J7J8J4P187P250P18522VDC,5VDC, GND5VDC,GND22VDC,5VDC, GNDJ6J322VDC, 5VDC, GND22VDC, 5VDC, GNDJ5J5J2AJ2BJAJBOverhead Antenna AssemblySide BT20231-G1Light Board Assembly (T20601-GX orM01560A00X)on Dispenser Bezel Face (Side A)POWER REGULATINGCircuit BoardT20314-G1P177P179P176P175P178Light Board Assembly(T20601-GX orM01560A00X)on Dispenser Bezel Face (Side A)P181P182RS-232, DigitalControl and LightControl CircuitP182P181RS-232, DigitalControl and LightControl CircuitM00878A002M00878A002M00878A002CableCableCableWhen overhead antennas are not part ofthe product, Dummy Load R20526-G1plugs into JA and JB. J2A and J2B areleft unconnected.R20773-G2, door cable,provides power and RS232communicationsR20773-G2, door cable,provides power and RS232communicationsX is color of LEDsDATA CONTROL BOARDQ13563-02 or -045 MHz (UHF Clock - selectedby jumper)10 MHz (Local Clock - notselected for this application)24 VACPower SupplyAC PowerEMCFilterQ10895-01Micro-ReaderQ13551-01(134 KHzIntentional)Micro-ReaderQ13551-01(134 KHzIntentional)M00878A002CableT20524BezelAntennaR20522-G2CableT20524BezelAntennaR20522-G2CableRS-232LF TX/RXLF TX/RXUHF RCVUHF RCVLF TXLF TXRS-485

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 11Full SystemsPreliminaryFigure 3-3: Encore Full System Block DiagramOverhead Antenna AssemblySide ALF Transmitter (134kHz IntentionalRadiator)Q13579-01Control DataUHF Receiver ModuleRI-RFM-HRUA902 - 928 MHz115 VAC(FROM DispenserAC POWERDISTRIBUTION)RS-232RS-232Gateway BoardT20128SERIAL DATAto CRIND logic boards(Dispenser Electronics)P187P250P18522VDC, 5VDC,GND5VDC,GND22VDC,5VDC, GND22VDC, 5VDC, GND22VDC, 5VDC, GNDJ2A J2BLF Transmit AntennaUHF Receive AntennaOverhead Antenna AssemblySide BLF Transmit AntennaUHF Receive AntennaLight Board AssemblyM01218A00Xon Dispenser Bezel Face (Side A)POWER REGULATINGCircuit BoardT20314-G1P177P179P176P175P178Light Board AssemblyM01218A00Xon Dispenser Bezel Face (Side A)P182RS-232, DigitalControl and LightControl CircuitP182RS-232, DigitalControl and LightControl CircuitJ1AJ3AJ3BJ1BM00878A001M00878A001M00878A001CableCableCableTuner Board T20579Tuner Board T20579Q13851-01 Q13851-01 WO3889 WO3889When overhead antennas are not part ofthe product, Dummy Load R20526-G1plugs into JA and JB. J2A and J2B areleft unconnected.R20773-G2, door cable,provides power and RS232communicationsR20773-G2, door cable,provides power and RS232communicationsX is color of LEDsDATA CONTROL BOARDQ13563-02 or -045 MHz (UHF Clock - selectedby jumper)10 MHz (Local Clock - notselected for this application)24 VACPower SupplyAC Power EMC FilterQ10895-01Micro-ReaderQ13551-01(134 KHzIntentional)Micro-ReaderQ13551-01(134 KHzIntentional)M00878A001CableEncoreAntenna(on boardEncorekeytagAntenna(on boardRS-232RS-485UHF RCVUHF RCVLF TX LF TX

Page 12 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013Hand Held Only Tag System OverviewPreliminaryHand Held Only Tag System OverviewThis product is an option available as a retrofit kit or factory installed equipment in Advantage, MPD-3, and Encore lines of fuel dispensers. The TRIND Enhanced Gateway Board (T20678) manages RFID processing and provides simple, generic event messages to the pump electronics via Transistor-Transistor Logic (TTL). In this application, TRIND is a software slave to the CRIND and the associated POS controller/host. This means that a properly working Low Frequency (LF) TRIND system will look for and read tags, but only when told to by the controller, through the CRIND application.This system is to be installed in accordance with all UL, FCC, federal, state and local regulations. The following block diagram depicts the components for the Hand Held Only Tag System.Figure 3-4: Hand Held Only Tag System Block Diagram115 VAC(FROM DispenserAC POWERDISTRIBUTION)R20580-G124 VACClass II EnergyLimitingTransformerR20719-G1115 VACT20524BezelAntennaT20524BezelAntennaEnhanced GatewayBoardT20678SerialDatato CRIND™ logic boards(Dispenser Electronics)RS-232, +22VDC, +5VDC, GNDRS-232, +22VDC, +5VDC, GNDP282A P282BP250P18522VDC,5VDC,GNDLight Board Assembly(T20601-G1)on Dispenser Bezel Face(Side B)RFID Power SupplyT20314-G1P174P177P178P176P175P179Light Board Assembly(T20601-G1)on Dispenser Bezel Face(Side A)P181P182RI-STU-MRD1Micro-Reader(134kHzIntentionalRadiator)RS-232, DigitalControl and LightControl CircuitP182P181RI-STU-MRD1Micro-Reader(134kHzIntentionalRadiator)RS-232, DigitalControl and LightControl CircuitEMI Line FilterQ10895-01 115 VAC

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 13Card Cage Assemblies Major Hardware ComponentsPreliminary4 – Major Hardware ComponentsCard Cage AssembliesThere are four main card cage versions used for the TRIND system. These four card cages are the T20229-G1, T20606-G2, T20606-G3, and the T20606-G5. The T20229 card cage is no longer available and is discussed in this manual simply for the service and support of the installed base. There are other G-levels of the T20606 card cage, but these are variations of the -G2 and -G3. Therefore, being familiar with these base card cages and their parts will provide the technician with valuable information in servicing the other G-levels if encountered. Note: Many parts look similar in the T20229 and T20606 card cages, but they are not the same. Always replace the removed part with the same part number or risk voiding the UL listings, FCC certifications, warranty, if applicable.T20229-G1 Card Cage AssemblyThe T20229 card cage was the installed card cage for the original Mobil Speedpass program. With a few cable changes, this card cage can be replaced by the T20606-G2, which contains the new Multi-Port DCB from Texas Instruments.Figure 4-1: Card Cage Assembly T20229-G112354

Major Hardware Components Card Cage AssembliesPage 14 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryT20229-G1 Card Cage Assembly Parts List Item Description Part Number1Power Supply PCB T20138-G12Transmitter PCB Assembly Q13579-013Data Control Board Q13563-014UHF Receiver Assembly on DCB Q13564-015Gateway Board T20128-G1T20606-G2 Card Cage AssemblyThe T20606-G2 card cage is the updated version of the T20229-G1. It features a Multi-Port DCB, LF Transmitter and a High-Gain UHF receiver. It also has a card cage harness, which reduces the number of field connections that must be made (compared to the T20229). This card cage comes ready to mount in an Encore unit, and is easily modified to also work in Eclipse, Advantage and MPD-3 units.Figure 4-2: Card Cage Assembly T20606-G218910117654321213

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 15Card Cage Assemblies Major Hardware ComponentsPreliminary T20606-G2 Card Cage Assembly Parts List Item Description Part Number1TRIND Gateway PCB T20128-G32Circuit Board Support Q10651-163TRIND PCB Bracket M00624A0014Multi-Port Data Control Board Q13563-045Radio PCB Shield R20545-G16PCB Insulator Board R20590-017Low Frequency Transmitter Module Q13579-01824 VAC Transformer R20719-G19Recessed Power Receptacle R20206-G1410 10 AMP EMI Filter Q10895-0111 TRIND PCB Shield Bracket M00621A00112 Regulator PCB Shield T20198-0113 Regulator PCB T20314-G1T20606-G3 Card Cage AssemblyThe T20606-G3 card cage supports “keytag only” operation and features an Enhanced Gateway board, which serves as the local controller for the RF modules (taking the place of the DCB) and the protocol handler for payment messaging (to CRIND or other Host Controller device). This card cage comes ready to mount in Encore, Advantage, Eclipse and MPD-3, with no modifications required. Figure 4-3: Card Cage Assembly T20606-G314253

Major Hardware Components Card Cage AssembliesPage 16 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryT20606-G3 Card Cage Assembly Parts List Item Description Part Number1Regulator PCB T20314-G12Shield, Regulator, PCB T20198-013Transformer, 24 VAC R20719-G14Enhanced Gateway PCB T20678-G15Filter, EMI, 10 AMP Q10895-01T20606-G5 Card Cage AssemblyThe T20606-G5 card cage is a variation of the T20606-G2 card cage required for many international “full system” TRIND applications (Europe and southeast Asia). It features a European Telecommunications Standards Institute (ETSI) Data Control Board (DCB), LF Transmitter and a High-Gain UHF receiver. It also has a card cage harness, which reduces the number of field connections that must be made (compared to the original T20229). This card cage comes ready to mount in an Encore unit, and is easily modified to also work in Eclipse, Advantage and MPD-3 units.Figure 4-4: Card Cage Assembly T20606-G518910117654321213

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 17Card Cage Assemblies Major Hardware ComponentsPreliminaryT20606-G5 Card Cage Assembly Parts List Item Description Part Number1TRIND Gateway PCB T20128-G32Circuit Board Support Q10651-163TRIND PCB Bracket M00624A0014ETSI Data Control Board Q13563-075Radio PCB Shield R20545-G16PCB Insulator Board R20590-017Low Frequency Transmitter Module Q13579-01824 VAC Transformer R20719-G19Recessed Power Receptacle R20206-G1410 10 AMP EMI Filter Q10895-0111 TRIND PCB Shield Bracket M00621A00112 Regulator PCB Shield T20198-0113 Regulator PCB T20314-G1Disassembly and Installation For MPD®-3 Units with SID DisplaysIn some older installations, a screw and two nuts were installed under the Card Cage on side B of a unit. This causes the installed card cage to rest at an angle, higher on side B. This hardware must remain in place in order to prevent contact between the Card Cage and the SID boards when the bezel door is closed.Disassembly and Installation For All MPD-3 UnitsIn field retrofits, the TRIND units’ top (center) screw from the card cage was removed, and replaced by tie wraps at either side after the card cage was installed in the cabinet. The card cage can only be removed or installed when separated into two pieces. See Figure4-5 for locations of the screw (1) and tie wraps (2).Figure 4-5: Screw and Tie Wrap Locations122

Major Hardware Components Card Cage AssembliesPage 18 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryAC EMI Line Filter Q10895AC EMI Line Filter Q10895-01, is a Corcom dual T section RFI power line filter. These filters are well suited for low impedance loads where noisy RFI environments are present. They control pulsed, continuous and/or intermittent interference, insuring protection of the TRIND equipment from power line noise in addition to protecting the line from equipment noise. Transformers R20600 and R20719Transformer R20600-G1 is used in T20229-G2 card cage assembly. Transformer R20719-G1 is used in T20606-G2 LF/UHF full system, and T20606-G2 Enhanced Gateway system card cages. Each transformer performs step down of 120VAC to a usable level for the RFID Power supply. The R20600 steps 120VAC down to 60VAC, which is used by the T20138-G1 Power Supply board. The R20719 steps 120VAC down to 24VAC, which is used by the T20314-G1 Power Supply board.Power Supply Boards T20138 and T20314Power Supply Board T20138-G1 is used in T20229-G1 full system card cage assembly. Power Supply Board T20314-G1 is used in T20606 line of card cages. The supplies take the output of their respective AC to AC transformers and make the proper DC voltages for use by the TRIND system components. Both supplies utilize a gate-driven MOSFET (for +22VDC) and a buck switched mode power supply (for +5VDC). Both supplies monitor the current on the output to turn off the gate drive, rather than fail permanently, should one of the TRIND system components develop a voltage problem. This arrangement allows for any of the outputs to be shorted directly to ground with out harming the power supply because it turns itself off until the problem is discovered and removed, and AC power is cycled.T20138 Power Supply Board. This board has jump-jack locations to set the dither sync (“Glossary” on page 1) address for the TRIND unit, with a 10-position ribbon cable (at P173) that goes to the DCB (J6). These addresses only matter to the site itself, not the pump or CRIND.Figure 4-6: Power Supply Board T201385VGND22VGND GND5V 22VGNDNote: P176, 177, and P178 are identical.JP1 through JP4: must be unique address for each dispenser at site22V 5V5V

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 19Card Cage Assemblies Major Hardware ComponentsPreliminaryT20314 Power Supply Board. Must be used in conjunction with R20719 transformer.Figure 4-7: Power Supply Board T203145VGND22VGND GND5V 22VGNDNote: P176, 177, and P178 are identical.22V5VData Control Boards Q13563Data Control Boards Q13563-01 and Q13563-02 are used in T20229-G1 full system card cage assembly. The Q13563-04 board is used in T20606-G2 full system card cage assembly. These DCBs handle tag reader control and pass the system status and tag data up to the Gateway board. The earlier versions (-01, -02) of this board made use of jump jacks on the power supply board for dither sync addressing, subsequent versions (-04 and above) contain dip switches for this site-specific addressing.Figure 4-8: Data Control Boards Q13563-01 and Q13563-02CR5 - pulsing (heartbeat) CR11 - RS485 - TXCR10 - RS485 - RXNote: In normal operation will be in sync.CR3 - 12VCR2 - 5VOn continuously

Major Hardware Components Card Cage AssembliesPage 20 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryFigure 4-9: Data Control Boards Q13563-03 and AboveQ13563-04 and AboveHeart BeatRS-485 TXRead ANT 1Read ANT 3Bezel I/0 ErrorBit RestoreBit FailRS-485 RX+12 Vdc+5 VdcUHF Receiver Board Q13564Mounted on the DCB, the UHF Receiver Board receives 12VDC from the DCB. The board also receives information from UHF antennas over J2A or J2B and processes the UHF signal. This receiver has to comply with FCC and in-country communication protocols such as ETSI. For this application the ETSI protocol is required for Asia and Europe.Figure 4-10: UHF Receiver Board Q13564

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 21Card Cage Assemblies Major Hardware ComponentsPreliminaryThe UHF Receiver Module contained on the DCB, handles the uplink signal from the vehicle tag. It receives the signal from the vehicle tag that transmits data on a UHF carrier, and down converts and demodulates this signal to binary data. The UHF Receiver also includes the master oscillator for the DCB and provides all clock signals for other elements within the DCB to keep signal paths as short as possible. The UHF receive antenna connections are made via Sub Miniature A (SMA) connectors on antenna cables M00878A001, M00878A002, and Q13578-01.Transmitter Board Q13579Transmitter Board Q13579-01 is used in the T20229-G1 and T20606-G2 full system card cages. The Transmitter Board is actually a three board assembly containing two identical transmitter modules (one each for Sides 1 and 2) mounted on a larger printed circuit board. The Transmitter Module (Q13579-01) contains all the functions to activate vehicle tags. The module includes a carrier board onto which are mounted two transmit-only Radio Frequency Modules (RFMs), the power supply, oscillator and tuning connector for the RFMs, logic circuitry to determine RFM selection, power level adjustment capability, and a pulse width modulation circuit. This board receives +22VDC, +5VDC and GND through J6. If this board is replaced, overhead antennas will need to be retuned. The transmitter provides an approximate 134 kHz signal for TRIND antennas, through JA for Side 1 and JB for Side 2 of the dispenser.Figure 4-11: Transmitter Board Q13579

Major Hardware Components Card Cage AssembliesPage 22 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryGateway Boards T20128, T20678Gateway Board T20128-GX is used in the T20229-G1 and T20606-G2 full system card cages. The T20678 Gateway Board is used in the T20606-G3 card cage. These boards manage events and message processing to/from the Controller (CRIND, POS, host controller) and the readers. On the full systems, the gateway board manages RFID processing through the DCB (which communicates with the vehicle tags via overhead antennas and with hand-held tags via bezel readers). On Enhanced Gateway systems, the board manages hand-held RFID processing through direct communication with the bezel readers.Figure 4-12: Gateway Boards T20128 and T20678TX = To A Side CRINDRX = From B Side CRINDPWR = 5VMust match corresponding CRIND addressT20128-GXCPU = Software RunningCPU = Software RunningPWR = 5VRX = From A Side CRINDTX = To A Side CRINDRX = From B Side CRINDTX = To B Side CRINDTX = To A Side CRINDT20678-GX

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 23Card Cage Assemblies Major Hardware ComponentsPreliminaryCard Cage Cable Harness T20662-G2The T20662-G2 card cage cable harness assembly provides power and data distribution to/from the card cage and the Light/MicroReader PCA. It comes already installed on the T20606-G2 card cage from the factory.Figure 4-13: Card Cage Cable Harness T20662-G2Full System TRIND R20520-G1 Transmitter CableThe R20520-G1 Transmitter Cable is a 26-pin connector cable that is routed between the Q13579 Low Frequency Transmitter Board and the Q13563 Data Control Board.Figure 4-14: Transmitter Cable R20520-G1

Major Hardware Components Card Cage AssembliesPage 24 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryFull System TRIND R20525-G1 RS-485 Communication CableThe R20525-G1 RS-485 Communication Cable is a 4-pin and 5-pin connector cable that is connected between the Q13563 Data Control Board and the T20128 Gateway Board.Figure 4-15: RS-485 Communication Cable R20525To Gateway Board To Data Control BoardFull System TRIND R20763-GX Power Supply CablesThe R20763-GX Power Supply Cables connect the LF Transmitter (-G1), the DCB (-G2) and the Gateway(-G3) boards to the T20314 power supply.Figure 4-16: Power Supply CablesR20763-G1R20763-G2R20763-G3

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 25Card Cage Assemblies Major Hardware ComponentsPreliminaryHand-Held TRIND System M00507 Ribbon CableThe M00507 Ribbon Cable is a 14-pin cable routed between T12678 Gateway Board and the R20773 TRIND Option Door Data and Power Cable. The R20773 cable leads to the T20601 Light/Microreader Board. The -A001 cable is used for Side A (or Side 1 based on the dispenser). The -A002 cable is used for Side B (or Side 2 based on the dispenser).Figure 4-17: Hand-Held TRIND System Ribbon Cable M00507Hand-Held TRIND System M01366 Power CableThe M01366 TRIND Power Cable is a 3-wire cable routed between the T20314 Power Supply Assembly and the T20678 Gateway Board.Figure 4-18: Hand-Held TRIND System Power Cable M01366

Major Hardware Components TRIND Overhead AntennasPage 26 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryTRIND Overhead AntennasFull System TRIND has six antennas, four active and two passive. The active antennas can further be divided as transmit only (overhead antennas) and transmit and receive (option door/CIM door antennas). All four operate in the Low Frequency (LF) band at 134.2 kHz. The two passive antennas receive in the UHF Band at 902 MHz (in the US) and at 868 MHz (Asia & Europe) and are used in conjunction with the overhead antennas to utilize the car tags. There are two basic variations of the full system TRIND. The fundamental differences are based on the card cage and the overhead antennas used. The antennas can be divided into two sections, the original Mobil antennas (no longer available) and the single-loop antennas, which are currently being shipped with full system TRIND. T20231 Mobil Overhead Antenna AssemblyThe Mobil overhead antenna assembly consists of a multiple loop (47 uH) coil for LF transmission, a tuning board, and sheet metal slot antenna for UHF receive. This assembly is no longer available, but is still a part of the installed base at Mobil Stations. These antennas have been replaced by T20632 family of overhead antennas.Figure 4-19: Mobil Overhead Antenna Assembly T2023156431, 2T20231 Mobil Overhead Antenna Assembly Parts ListItem Description Part Number1902.858 MHz high frequency antenna Q13580-012868.4 MHz High Frequency Antenna Q13580-023Molded Antenna Q13582-014Tuning Board Q13582-025Tuner Gasket Q13582-046Tuner Cover Q13582-03

Major Hardware Components TRIND Overhead AntennasPage 28 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryT20231 Mobil Overhead Antenna Bracket Assemblies and Hardware for The Advantage SeriesItem Description Wide Frame Single-Sided Wide Frame Double-Sided Narrow Frame Single-Sided Narrow Frame Double Sided1antenna top cover T20213-01 T20213-01 T20215-01 T20215-012bracket, universal antenna T20212-01 T20212-01 T20212-01 T20212-013bracket, antenna mounting T20211-01 T20211-01 T20211-01 T20211-013a bracket, antenna mounting (note 1) T20211-02 -T20211-02 -4screw, 10-32 black K85736-45 K85736-45 K85736-45 K85736-455antenna assembly T20231-G1 T20231-G1 T20231-G1 T20231-G161/4-20 bolt x 4" black K01914-70 K01914-70 K01914-70 K01914-7071/4-20 nut, black Q11890-08 Q11890-08 Q11890-08 Q11890-088over head antenna cables R20509-G1Q13578-01R20509-G1Q13578-01R20509-G1Q13578-01R20509-G1Q13578-019connector, tube fitting Q13591-01 Q13591-01 Q13591-01 Q13591-0110 conduit, flexible black plastic Q13592-02 Q13592-02 Q13592-02 Q13592-02Notes:1. Not shown on page 28, single-sided antenna bracket has no antenna mounting arms.T20231 Mobil Overhead Antenna Bracket Assemblies and Hardware for the MPD-3Item Description PMI BezelSingle-Sided PMI BezelDouble-Sided Mack BezelSingle-Sided Mack BezelDouble Sided1antenna top cover T20214-01 T20214-01 T20214-01 T20214-012bracket, universal antenna T20212-01 T20212-01 T20212-01 T20212-013bracket, antenna mounting T20211-01 T20211-01 T20211-01 T20211-013a bracket, antenna mounting (note 1) T20211-02 -T20211-02 -4screw, 10-32 black K85736-45 K85736-45 K85736-45 K85736-455antenna assembly T20231-G1 T20231-G1 T20231-G1 T20231-G161/4-20 bolt x 4" black K01914-70 K01914-70 K01914-70 K01914-7071/4-20 nut, black Q11890-08 Q11890-08 Q11890-08 Q11890-088over head antenna cables R20509-G1Q13578-01R20509-G1Q13578-01R20509-G1Q13578-01R20509-G1Q13578-019connector, tube fitting Q13591-01 Q13591-01 Q13591-01 Q13591-0110 conduit, flexible black plastic Q13592-02 Q13592-02 Q13592-02 Q13592-02Notes:1. Not shown on page 28, single-sided antenna bracket has no antenna mounting arms.

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 29TRIND Overhead Antennas Major Hardware ComponentsPreliminaryT20632 Single-Loop Overhead Antenna AssemblyThe T20632-GX Single-Loop Overhead Antenna Assemblies are made up from a single turn (loop) antenna; a high efficiency tuning board, and a UHF receive antenna. These parts are all mounted in a molded polycarbonate set of boxes and then mounted with brackets on top of the dispenser. These parts are discussed in further in the following sections.Note: There are eight different “G” levels of this antenna assembly, due to the different widths and heights of the dispensers. T20632 “G” Level Dispenser Antenna is used on G1/G5 Advantage Wide Frame and MPD-3G2/G6 Advantage Narrow FrameG3/G7 EncoreG4/G8 Advantage Wide Frame With Exxon Light BoxSub Miniature A (SMA) connections should be treated with care and not overtightened. The maximum torque rating on these connectors is usually measured in inch poundsToo severe a turn or bend in the cable may damage the center conductor or compromise the shield/drain portion of the cable. This can result in an observance of intermittent reads or other problems. The poor performance will in turn generate a premature field service call. Replacing this cable is labor intensive after the system is installed the first time.Turns or bends in coaxial cable must be gradual loops, no sharper than a 1-inch radius (2-inch diameter).CAUTIONCAUTIONIt is critical that the proper tool is used when tuning the overhead antennas on TRIND systems. Only the Q13631-02 (part of ASC Tool Kit K94577-01) plastic tuning tool (or similar plastic 0.10in. hex tool) should be used for tuning overhead antennas. Using a metal screwdriver or Allen wrench has two negative effects. First, a proper tuning is impossible as the metal of the tool used changes the properties of the variable inductor used for tuning. Second, the ferrite slug used in the variable inductor is extremely brittle and is broken or stripped easily by metal tools, preventing the proper tuning of the antenna. If the antenna is not properly tuned the read range can be significantly reduced

Major Hardware Components TRIND Overhead AntennasPage 30 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryFigure 4-21: T20632 Single-Loop Overhead Antenna Assembly8432165117109T20632 Single-Loop Overhead Antenna Assembly Parts List (Domestic)Item Description T20632-G1 T20632-G2 T20632-G3 T20632-G41Bottom Right Antenna Box T20615-04 T20615-04 T20615-04 T20615-042Top Right Antenna Box T20615-02 T20615-02 T20615-02 T20615-023 Antenna W03889-01 W03889-02 W03889-03 W03889-044Bottom Left Antenna Box T20615-03 T20615-03 T20615-03 T20615-035Screw Thread Form #6-19 Q12011-17 Q12011-17 Q12011-17 Q12011-176Antenna Tuner PCA T20579-G1 T20579-G2 T20579-G3 T20579-G47Lock Washer K46212 K46212 K46212 K462128Top Left Antenna Box T20615-01 T20615-01 T20615-01 T20615-019Hex Nut Q11890-04 Q11890-04 Q11890-04 Q11890-0410 UHF Receiver Antenna Q13851-01 Q13851-01 Q13851-01 Q13851-0111 Neoprene Adhesive Tape Q11899-12 Q11899-12 Q11899-12 Q11899-12

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 31TRIND Overhead Antennas Major Hardware ComponentsPreliminaryT20632 Single-Loop Overhead Antenna Assembly Parts List (International)Item Description T20632-G5 T20632-G6 T20632-G7 T20632-G81Bottom Right Antenna Box T20615-04 T20615-04 T20615-04 T20615-042Top Right Antenna Box T20615-02 T20615-02 T20615-02 T20615-023 Antenna W03889-01 W03889-02 W03889-03 W03889-044Bottom Left Antenna Box T20615-03 T20615-03 T20615-03 T20615-035Screw Thread Form #6-19 Q12011-17 Q12011-17 Q12011-17 Q12011-176Antenna Tuner PCA T20579-G1 T20579-G2 T20579-G3 T20579-G47Lock Washer K46212 K46212 K46212 K462128Top Left Antenna Box T20615-01 T20615-01 T20615-01 T20615-019Hex Nut Q11890-04 Q11890-04 Q11890-04 Q11890-0410 UHF Receiver Antenna Q13851-02 Q13851-02 Q13851-02 Q13851-0211 Neoprene Adhesive Tape Q11899-12 Q11899-12 Q11899-12 Q11899-12Figure 4-22: T20632 Single Loop Antenna Brackets and Hardware13566465623

Major Hardware Components TRIND Overhead AntennasPage 32 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryT20632 Single Loop Antenna Assembly Bracket Kits for The Advantage SeriesItem Description W/F & N/F RID Plus Exxon (K96647-01) With Canopy (K96647-02)With Or With Out Blue Hats (K96647-03)With Milwaukee Light Box (K96647-06)1Antenna Bracket, Left T20623-01 T20624-01 - -2Antenna Bracket, Right T20623-02 T20624-02 - -1Antenna Bracket, W/F & N/F - - T20625-01 -2Antenna Bracket, W/F & N/F - - T20625-02 -1Antenna Bracket, ADV & MPD-3 - - - T20628-012Antenna Bracket, ADV & MPD-3 - - - T20628-023Gasket, Mounting Bracket N23958-01 N23958-01 N23958-01 N23958-014Gasket, Antenna Wire Bracket N23959-01 N23959-01 N23959-01 N23959-015Screw, Hex Head Q11889-104 Q11889-104 Q11889-104 Q11889-1046Fastener, Self-Drilling - - - Q13897-01T20632 Single Loop Antenna Assembly Bracket Kits for the MPD-3 SeriesItem Description With Canopy (K96647--04)With Out Canopy (K96647-05)With Milwaukee Light Box (K96647-06)1Antenna Bracket, Left T20626-01 T20627-01 -2Antenna Bracket, Right T20626-02 T20627-02 -1Antenna Bracket, ADV & MPD-3 - - T20628-012Antenna Bracket, ADV & MPD-3 - - T20628-023Gasket, Mounting Bracket N23958-01 N23958-01 N23958-014Gasket, Antenna Wire Bracket N23959-01 N23959-01 N23959-016Screw, Hex Head Q11889-104 Q11889-104 Q11889-1046Fastener, Self-Drilling - - Q13897-01T20632 Single Loop Antenna Assembly Bracket Kit for the Encore UnitItem Description K96647--071Antenna Bracket, Encore T20630-012Antenna Bracket, Encore T20630-023Gasket, Bracket Mounting N23958-014Gasket, Antenna Wire Bracket N23959-015Screw, Hex Head Q11889-104

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 33TRIND Overhead Antennas Major Hardware ComponentsPreliminaryUltra High Frequency Antenna Q13851-01 and Q13851-02This antenna is specifically used to receive the UHF response from the vehicle mount tag. It has a “pigtail” RG-316 coaxial cable with a Sub Miniature A (SMA) jack on the other end connected to it for ease of manufacture and installation purposes. Q13851-01 is intended for domestic use and is found in the T20632-G1 through T20632-G4 Single Loop Antenna Assemblies. Q13851-02 is intended for international use and is found in the T20632-G5 through T20632-G8 Single Loop Antenna Assemblies.Antenna Tuning Board T20579-GXThe Antenna Tuning Board (T20579-GX) allows the resonance tuning of the low frequency downlink antenna to match with the Transmitter Module to compensate for product tolerances at manufacturing, and to achieve the maximum field strength. The antenna circuit is tuned to resonance by adjusting the ferrite core of the on-board coil with a 0.10-inch hex tuning tool located in K94577-01 ASC TRIND Tool Kit. Important: The “G” level of this board must match the “G” level of the final assembly. Capacitance values are different between the boards due to the different sizes of the single loop antenna itself.

Major Hardware Components TRIND Option Doors With AntennasPage 34 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryTRIND Option Doors With AntennasThis section provides descriptions and parts information for TRIND options contained in the doors of the Advantage, MDP-3, Encore and Eclipse dispensers. This version of TRIND consists of RFID components, including the antenna, mounted on the door. The antennas used for the option doors on the Advantage and the Encore/Eclipse, perform transmit and receive functions and interact directly with a microreader that’s contained on a light board located in the door. The inductive antennas utilize the magnetic near field (air interface) generated by the microreader to interact with the hand-held tags.The T20601-G1/G2 Light MicroReader PCA is used on the Advantage and MPD-3 dispensers. The T20601-G1 board has red LEDs, the T20601-G2 board has orange LED's. The LEDs light to provide an indication to the consumer that the key tag has been read. In addition, the board processes data received from the key tag antenna, and sends the processed data to the DCB or Enhanced Gateway board. The Key-Tag Antenna (T20524-G1) is used on Advantage and MPD-3 dispensers. It connects to the T20601-GX PCA, and is used as an antenna for the key tag portion of the system. An R20522-G2 cable provides a connection between the T20524 and T20601 PCAs.The M01218A001/A002 Light MicroReader/Antenna PCA is used on the Encore/Eclipse dispensers. The M01218A001 board has red LEDs, M01218A002 board has orange LED's. The board provides indication to the consumer that the tag has been read. In addition, the board processes data received from the key tag antenna, and sends the process data to the DCB or Enhanced Gateway board. The antenna for key-tag portion of the system has been integrated into this assembly. This board also has the ability to be re-configured from red to orange LEDs, and vice-versa, in the field.

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 35TRIND Option Doors With Antennas Major Hardware ComponentsPreliminaryMPD-3 Bezel AssembliesThe following sections provides parts information for the MPD-3 Bezel Assemblies.Figure 4-23: T20616-G1 MPD-3 Bezel Assembly7510116431892 T20616-G1 MPD-3 Bezel Assembly Parts List Item Description Part Number1Housing, MPD-3 T20417-G12Tape, Single Coated Neoprene Sponge Q11899-023TI/RFID Antenna Assembly T20524-G14Light Micro Reader PCA T20601-G15Inside Cover Gasket R20584-016Inside Cover, MPD-3 Housing T20216-017Bezel Panel Assembly T17446-G88 Interface Hand Held Antenna Cable R20522-G29TRIND Option Door Data and Power Cable R20773-G210 Cable Access Gasket N23881-0111 Plate, Lock N23873-G1

Major Hardware Components TRIND Option Doors With AntennasPage 36 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryFigure 4-24: T20616-G2 MPD-3 Bezel Assembly7510643189211131214 T20616-G2 MPD-3 Bezel Assembly Parts List Item Description Part Number1Housing, MPD-3 T20179-012Tape, Single Coated Neoprene Sponge Q11899-023TI/RFID Antenna Assembly T20524-G14Light Micro Reader PCA T20601-G15Inside Cover Gasket R20584-016Inside Cover, MPD-3 Housing T20216-017Bezel Panel Assembly (Note 1) T17534-G058 Interface Hand Held Antenna Cable R20522-G29TRIND Option Door Data and Power Cable R20773-G210 Cable Access Gasket N23881-0111 Spacer, Split (Note 2) K87404-0112 Gasket, 0.88 O.D. (Note 2) Q11659-0113 Washer (Note 2) N16599-7814 Nut, Self Locking Hex (Note 2) Q10218-01Notes:1. Bolt-On Panel for Mack Bezels.2. Bezel Assembly requires a quantity of six (6).

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 37TRIND Option Doors With Antennas Major Hardware ComponentsPreliminaryFigure 4-25: T20251-G1 MPD-3 Bezel Assembly61254397141112151381016T20251-G1 MPD-3 Bezel Assembly Parts List Item Description Part Number1housing, MPD-3 T20179-012tape, single coated neoprene sponge Q11899-023o-ring, 4.25 x 4.28 Q13575-024lens, Mobil Q13575-015diffuser Q13575-036bracket, lens retainer Q13575-047TI/RFID Antenna PCB assembly T20143-G18TI/RFID Light/Microreader PCB T20446-G19gasket, inside cover R20584-0110 inside cover, MPD-3 housing T20216-0111 bezel panel assembly T17446-G8 (note 1)12 gasket, cable access N23881-0113 plate, lock N23873-G114 cable, hand held antenna interface R20522-G115 cable, light microreader R20519-G316 interface/microreader, cable R20521-G3Notes:1. Slide-in panel for PMI bezels.

Major Hardware Components TRIND Option Doors With AntennasPage 38 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryAdvantage Wide Frame Option Door AssembliesThis section provides parts data for the Advantage Wide Frame Option Doors. Assemblies.Figure 4-26: T20228-G1 Advantage Wide Frame (48-Inches) Option Door Assembly19876542310T20228-G1 Advantage Wide Frame Option Door Assembly Parts ListItem Description Part Number1TI/RFID Door Antenna T20143-G12Light microreader PCB (note1) T20446-G13antenna shield T20210-014lens retainer bracket Q13575-045diffuser, Wayne Q13575-036logo lens Q13575-017O-ring Q13575-028door gasket R20424-019option door, right T17499-0610 Antenna Interface Cable R20522-G1Notes:1. Replaced T20182-G1 and T20295-G1

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 39TRIND Option Doors With Antennas Major Hardware ComponentsPreliminaryFigure 4-27: T20613 Advantage Wide Frame (48-Inches) Option Door Assembly654312 T20613 Advantage Wide Frame Option Door Assembly Parts ListItem Description Part Number1Wide Frame Shield T20570-G12Solid Strip Grommet Q10315-063RFID Light/ Microreader PCA (note 1) M01580A00X4TRIND Antenna PCB T20524-G15Door Gasket R20424-016Right Option Door (note 2) T20415-0XNotes:1. Order entry item available as -A001 and -A0022. Order entry item available as -01 through -08.

Major Hardware Components TRIND Option Doors With AntennasPage 40 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryAdvantage Narrow Frame Option Door AssembliesThis section provides parts data for the Advantage Narrow Frame Option Doors.Figure 4-28: T20614 Advantage Narrow Frame (36-Inches) Option Door Assembly67524318T20614 Narrow Frame Option Door Assembly Parts ListItem Description Part Number1Solid Strip Grommet Q10315-062N/F Door Shield T20571-G13RFID Light/Micro Reader (note 1) M01580A00X4TRIND Antenna Assembly PCB T20524-G15Display PCB Assembly T20262-G16Access Door Gasket R20424-017N/F Option Door T20416-01Notes:1. Order entry item available as -A001 and -A002

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 41TRIND Option Doors With Antennas Major Hardware ComponentsPreliminaryFigure 4-29: T20253-G1 Advantage Narrow Frame (36-Inches) Option Door Assembly2134567910111213814T20253-G1 Narrow Frame Option Door Assembly Parts ListItem Description Part Number1N/F Option Door (note 1) T20125-0X2O-ring Q13575-023Mobil lens Q13575-014Diffuser Q13575-035Lens Retainer Bracket Q13575-046TI/RFID Light/Microreader PCB (note 2) T20446-G17antenna shield T20210-028Cable, Hand Held Interface R20522-G19Display PCB Assembly T20262-G110 TI/RFID Antenna PCB T20143-G111 Display Lens Mounting Bracket R20586-0112 Display Lens R20585-0113 Display Lens Gasket N23879-0114 Access Door Gasket R20424-01Notes:1. Order entry item available as -01 and -02.2. Replaced T20295-G1.

Major Hardware Components TRIND Option Doors With AntennasPage 42 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryEncore CIM Door Option AssemblyThis section provides the parts for the Encore CIM Door Option Assembly.Figure 4-30: 654321Encore CIM Door Option AssemblyEncore CIM Door Option Assembly Parts ListItem Description Part Number1Screw, Hex Head 6-20 Q11677-242TRIND Light and Indicator Assembly M01218A00X (note 1)3CIM Door with CRIND Assembly M01208A0014TRIND Panel Gasket M01160B0015TRIND Display Window Lens M01234B0016Screw, Phillips M00419B117Notes:1. Order entry item available as red (-A001) or orange (-A002).

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 43TRIND Option Doors With Antennas Major Hardware ComponentsPreliminaryEclipse Ovendoor Option AssemblyThis section provides the parts for the Eclipse Ovendoor Option Assembly.Figure 4-31: 12345Eclipse Ovendoor Option AssemblyEclipse Ovendoor Option Assembly Parts ListItem Description Part Number1Eclipse TRIND/Cash Acceptor Ovendoor M01509A0012Eclipse Ovendoor TRIND Assembly M01661A0013TRIND PCB Cover M01408B0014Slotted 6-20X.3125 Screw Q11677-235TRIND Light and Indicator Assembly M01218A00X (note 1)Notes:1. Order entry item available as red (-A001) or orange (-A002).

Major Hardware Components TRIND Option Doors With AntennasPage 44 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryLight/Microreader PCB T20446-G1, T20601-GX, M01580A001, and M01580A002 Note: T20446 replaced Light/Microreader PCB T20182-G1 and T20295-G1. M01580A001 and M01580A002 replaced Light/Microreader PCB T20601-G1 and G2The PCB is mounted on the right options door on The Advantage Series units or in an enclosure mounted on the bezel for MPD-3 units. The PCB processes data received from the hand-held transponder and provides tag read indicator lights for the TRIND system. The PCB requires both 5VDC and 22.5VDC supplied at plug P182. The PCB also provides hand-held transmitter information to the DCB or Enhanced Gateway board. In addition, the PCB receives information regarding light control from the DCB. These activities are also done through plug P182.Figure 4-32: Light/Microreader Printed Circuit Board T20446-G1Note: Used With Card Cage T20229 In Kit C00011-001.Figure 4-33: Light/Microreader Printed Circuit Board T20601-G1Note: Used With Card Cage T20606-GX In Kits C00011-002 And Above.

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 45TRIND Option Doors With Antennas Major Hardware ComponentsPreliminaryFigure 4-34: Light/Microreader Printed Circuit Board M01580A00X Note: Used With Card Cage T20606-GX In Kits C00011-002 And Above.Light/Microreader PCB M01218A001 and M01218A002Mounted on the CIM Door on Encore and Eclipse units, this PCB processes information received from hand-held transponder (only), as well as provide indicator lights for the TRIND system. The PCB requires both 5VDC and 22.5VDC supplied at P182. The PCB provides transmitter activity data to the DCB, and receives light control information from the DCB. These activities are done through P182. The antenna is integrated into this assembly.Figure 4-35: Light/Microreader Printed Circuit Board M01218A00X

Major Hardware Components TRIND Option Doors With AntennasPage 46 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryHand-Held Antenna PCB T20143-G1Hand-Held PCB T20143-G1 is used on the original system and is connected to Light/Microreader PCB (i.e. T20182) at P181 and mounted on options or bezels doors.Figure 4-36: Hand Held Antenna Printed Circuit Board T20143-G1 TRIND Antenna PCA T20524-G1The T20524-G1 PCAs are 47uH antennas that work with the Microreader. They are energized by the Microreader at 132 kHz to generate the exciter frequency of 134.2 kHz.Figure 4-37: TRIND Antenna PCA T20524-G1

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 47System Cables Major Hardware ComponentsPreliminarySystem CablesThis section provides a description and parts information for the TRIND system cables. These cables are used to make connections between the various TRIND and dispenser components that comprise the TRIND system.M00878 Low/High Frequency Antenna CableThe overhead antenna cable assemblies M00878A001 and M00878A002, connect the overhead antennas to the TRIND UHF receiver and LF transmitter. The M00878A001 cable is used for the Encore units, the M00878A002 is used for the Advantage and MPD-3 units. Note: If the unit has an Exxon Lightbox, there is an overhead antenna cable extension (M01380A001) used for this configuration.Figure 4-38: M00878A001M00878A002Low/High Frequency Antenna CableR20773 Power and Data Option Door Cable The R20773 cable is a power and data option door cable that connects the Light/Micro-Reader PCA to the TRIND card cage. Note: This cable exists in some quantities as 55 inches long. This was eventually changed to 70 inches long (Revision C and above). If you encounter the shorter version, you will need an extender cable (M01557A001) for each side of the dispenser. Figure 4-39: Power and Data Option Door Cable R20773To DCB or Enhanced Gateway BoardTo TRIND Light Board

Major Hardware Components System CablesPage 48 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryR20437-G01 TRIND to CRIND Logic Cable (Advantage and MPD-3)The R20437-G01 TRIND to CRIND Logic Cable connects the TRIND Gateway Broads (T20128 and T20678) to CRIND Logic boards.Figure 4-40: TRIND to CRIND Logic Cable R20437M00515A002 TRIND to CRIND Logic Cable For Encore 500 and EclipseThe M00515A002 TRIND to CRIND Logic Cable for Encore 500 and Eclipse connects the Gateway Boards to the CRIND Logic Boards.Figure 4-41: TRIND to CRIND Logic Cable M00515A002

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 49System Cables Major Hardware ComponentsPreliminaryM001804A001 TRIND to CRIND Logic Cable for Encore 300The M001804A001 TRIND to CRIND Logic Cable for Encore 300 connects the Gateway Boards to the CRIND Logic Boards.Figure 4-42: TRIND to CRIND Logic Cable M001804A001 R20580 and M00811A001 AC Power CablesThe R20580 and M00811A001 AC Power Cables are used to provide system power to the TRIND card cage assembly. Connections for these cables are unit specific. Use appropriate connector to intercept power on existing unit power cable.Figure 4-43: AC Power CablesR20580M00811A001

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 51System Cables Major Hardware ComponentsPreliminaryFull System Cable Connections on the MPD-3 DispensersFor all single-sided units, install dummy load connector R20526-01 on JB on transmitter PCB and skip all ‘B’ side connections.Note: If power is applied to card cage without the antenna cables or dummy load connected, the transmitter board will be damaged.Note: Asterisk(*) indicates connection point is on card cage assembly.On Cable Connect To OnR20509-G2 (marked for ‘A’ side) P1/2 J1 ‘A’ side overhead antenna (low freq)PA/B *JA Transmitter PCB Q13564R20509-G2 (‘B’ side, unmarked) P1/2 J2 ‘B’ side overhear antenna (low freq)PA/B *JB Transmitter PCB Q13564R20519-G3 (marked for ‘A’ side) J182 P182 Light/microreader PCB assembly T20182 on ‘A’ side faceplate assemblyP7 *J7 DCB PCB Q13563R20519-G3 (‘B’ side, unmarked) J182 P182 Light/microreader PCB assembly T20182 on ‘B’ side faceplate assembly P8 *J8 DCB PCB Q13563R20521-G3 (marked for ‘A’ side) J180 P180 Light/microreader PCB assembly T20182 on ‘A’ side faceplate assemblyJ177 *P177 Power supply PCB T20138GRD *Ground stud Card cageR20521-G3 (‘B’ side, unmarked) J180 P180 Light/microreader PCB assembly T20182 on ‘B’ side faceplate assemblyJ176 *P176 Power supply PCB T20138GRD *Ground stud Card cageQ13578-01 -01 (marked for ‘A’ side) P1 J1 ‘A’ side overhead antenna (high freq)P1 *J2B Receive PCBQ13578-01 (‘B’ side, unmarked) P1 J2 ‘B’ side overhead antenna (high freq)P1 *J2A Receive PCBR20437-G01 J250 *P250 TI Gateway PCB T20128-G1J258A P258 ‘A’ side CRIND logic PCB T17764J258B P258 ‘B’ side CRIND logic PCB T17764R20580-G1 P601J6013 prong F 3 prong M Card cage, rear

Major Hardware Components System CablesPage 56 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryM00878A001 and M00878A002 Antenna Cable Pin-to-Pin ConnectionsP1B To J1 Pin # on Side 1 Overhead Low Frequency AntennaP1A To J1 Pin # on Side 2 Overhead Low Frequency AntennaP3B To J2 Pin # on Side 1 Overhead High Frequency AntennaP3A To J2 Pin # on Side 2 Overhead High Frequency AntennaPB To JB for Side 1 Pin # on Q13579 Transmitter BoardPB To JB for Single-Side Units Only With R20526-G1 Power Resistor PA To JA for Side 2 Pin # on Q13579 Transmitter BoardP2A To J2A for Side A Pin # on Q13564 UHF Receive BoardP2B To J2B for Side B Pin # on Q13564 UHF Receive Board11111N.C. 1112 2 - - 2 N.C. 2 - -- - - - 3 - 3 - -M00515A002 Ribbon Cable Pin-to-Pin Connections J/PA To P250 Pin # On Gateway PCB T20128 To P3110 Pin # on CRIND Control Node M00089 Function112 RX_A213 GND_A314 TX_A411 +5V_A5 - SPARE_IN_A6 - N.C.7 - SPARE_OUT_A8 5 RX_B9 6 GND_B10 -TX_B11 4+5_B12 -SPARE_IN_B13 - N.C.14 -SPARE_OUT_BR20509-G1 Antenna Cable, Low Frequency Pin-to-Pin ConnectionsFor single-sided units R20526 (see below) replaces R20509-G1 cable used on side B. To JA/JB Pin # on Low Frequency Transmitter Board Q13579 To J1/J2 Pin # on Over Head Low Frequency Antenna1 12 23* unusedNote: Asterisk (*)To Ground

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 57System Cables Major Hardware ComponentsPreliminaryR20519-G1, -G2 and -G3 Light/Microreader Cables Pin-to-Pin ConnectionsTo J7/J8 Pin # on Data Control Board Q13563 To P182 on Light/Microreader PCB T20182 Function1 1 TX 2322 2 GPO 2323 3 AX 2324 4 Light 2325 5 RDEN6 6 GNDR20521-G1 and -G2 Interface Microreader Cables Pin-to-Pin ConnectionsTo P176/P177 Pin # on Power Supply Board T20314 To P180 Pin # on Light/Microreader PCB T20182 Function1 1 +22v2 2 +5v3 3 GNDR20522-G1 Interface Hand Held Antenna Cable Pin-to-Pin ConnectionsTo P190 Pin # on Hand Held Antenna T20143 To P181 Pin # on Light/Microreader PCB T201821 12 2R20522-G2 Interface Hand Held Antenna Cable Pin-to-Pin ConnectionsTo P190 Pin # on Hand Held Antenna T20524 To P181 Pin # on Light/Microreader PCB T206011 12 2R20526 TI/RFID Dummy Load Transmitter Cable Pin-to-Pin ConnectionsUsed for single-sided units in place of ‘B’ side R20509-G1 cable to provide dummy load. If TRIND® unit is powered without load on both ‘A’ and ‘B’ side of Low Frequency Transmitter Board Q13579 board will be damaged. R20526 Pin # To JB Pin # on Low Frequency Transmitter Board Q135791 12 23 3

Major Hardware Components System CablesPage 58 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryR20437-G01 TRIND to CRIND Logic Cable Pin-to-Pin ConnectionsPin # on T20128 Gateway PCB Pin # Side A P258 of CRIND™ Logic Board Pin # on Side B P258 of CRIND™ Logic Board Function1 1 - RX-A2 2 - GND-A3 3 - TX-A4 4 - +5V-A5 5 - Spare-In-A6 6 - N.C.7 7 - Spare-Out-A8 - 1 RX-B9 - 2 GND-B10 - 3 TX-B11 - 4 +5V-B12 - 5 Spare-In-B13 - 6 N.C.14 - 7 Spare-Out-BAdvantage Option R20773-G2 TRIND Data and Power Cable Pin-to-Pin ConnectionsTo Pin # on Side 1 and Side 2 M01218A001/A002 Microreader PCB Plug P182 To Pin # on TRIND Card Cage Harness Cable T20662-G2 Plug P1 and P2 Function1 1 TX2 2 RX3 3 GPO4 4 GND5 5 VCC6 6 N.C.7 7 -8 8 ILLUM9 9 GND10 10 +22V11 11 RDEN12 12 N.C.

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 59System Cables Major Hardware ComponentsPreliminaryEncore Option R20773-G2 TRIND Data and Power Cable Pin-to-Pin ConnectionsTo Pin # on Side A and Side B T20601 Light/Microreader PCB Plug P182 To Pin # on TRIND Card Cage Harness Cable T20662-G2 Plug P1 and P2 Function1 1 TX2 2 RX3 3 GPO4 4 GND5 5 VCC6 6 N.C.7 7 -8 8 ILLUM9 9 GND10 10 +22V11 11 RDEN12 12 N.C.T20662-G2 TRIND Card Cage Cable Harness Cable Pin-to-Pin ConnectionsFrom P1 Pin # on T20662 TRIND Card Harness CableTo J1/J2 Pin # on Side 1 R20773 TRIND Data and Power CableFrom P2 Pin # on T20662 TRIND Card Harness CableTo J1/J2 Pin # on Side 2 R20773 TRIND Data and Power CableFrom P7 Pin # on T20662 TRIND Card Harness CableTo J7 Pin # For Q13563 Data Control Board From P8 Pin # on T20662 TRIND Card Harness CableTo J8 Pin # For Q13563 Data Control Board From J176 Pin # on T20662 Card Harness Cable To P176 Pin # on T20314 Power Supply PCBFrom J177 Pin # on T20662 Card Harness Cable To P177 Pin # on T20314 Power Supply PCB1 1 1 1 1 1 1 1 1 1 1 12 2 2 2 2 2 2 2 2 2 2 23 3 3 3 3 3 3 3 3 3 3 34 4 4 4 4 4 4 4 - - - -5 5 5 5 5 5 5 5 - - - -6 6 6 6 6 6 6 6 - - - -7 7 7 7 - - - - - - - -8 8 8 8 - - - - - - - -9 9 9 9 - - - - - - - -10 10 10 10 - - - - - - - -11 11 11 11 - - - - - - - -12 12 12 12 - - - - - - - -

Major Hardware Components System CablesPage 60 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryThis page is intentionally left blank.

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 61ASC TRIND Tool Kit K94577-01 System AccessoriesPreliminary5 – System AccessoriesASC TRIND Tool Kit K94577-01Authorized Service Contractor (ASC) TRIND Tool Kit contains specialized tools required for installation and service of TRIND equipped units.Kit Contents The K94577-01 tool kit contains the following itemsDescription Part Number Quantity cable, standalone jumper R20602-G1 1cable, standalone jumper R20602-G2 1co-axial cable tool Q13628-01 1field strength sensor board Q13626-01 1test tag, TI/RFID car mount Q13630-01 1test tag, TI/RFID hand held Q13630-02 1threaded rod, 3/8-16 x 4" N23880-01 4tuning tool, plastic tipped Q13631-01 1tuning tool, plastic tipped Q13631-02 1.Standalone Jumper CablesStandalone Jumper Cable R20602-G1 For LF/UHF Full SystemThis cable is used for MPD-3 installation or troubleshooting on any unit that requires placing the unit the standalone mode. After powering down unit, either A or B side R20519-G3 cable is disconnected from either J8 (B side) or J7 (A side) on DCB in the TRIND card cage, and R20602-G1 is connected in-line (between J8 and P8 or between J7 and P7). A standard alkaline 9 volt battery (not supplied with kit) must be connected to R20602-G1 cable.Figure 5-1: Standalone Jumper Cable R20602-G1

System Accessories Standalone Jumper CablesPage 62 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryNote: If Standalone Jumper or 9 volt battery is not available, unit can be put in standalone using the jump jack on JP3.Connector on R20602-G1 Connects To OnJ7/J8 Either J7 or J8 DCB PCB on card cageP182 Either P7 or P8 A or B side R20519-G3 cableBattery connectors Battery terminals standard 9 volt alkaline batteryFigure 5-2: R20602-G1 Card Cage Connections and Wiring Diagram J8 and J7on TRIND card cageWiring Diagram

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 63Standalone Jumper Cables System AccessoriesPreliminaryStandalone Jumper Cable R20602-G2 For Enhanced GatewayThis cable is used for installation or troubleshooting, and for placing a unit in the “standalone” mode. The hand-held key tag units contain the T20606-G3 Card Cage Assembly and the T20678-G1 Enhanced Gateway PCB. After powering down unit, the P1 end of the M00507A001 cable coming out of the card cage on Side A is disconnected. The P1/P2 end of the R20602-G2 cable is connected to the P1 end of the M00507A001 cable, and the J1/J2 end of the R20602-G2 cable is connected to the J1/J2 end of the R20773-02 cable that is connected to the M01218A001 Light Board Assembly. TRIND is in the “standalone” mode when power is restored to the unit. Connector on R20602-G2 Connects To OnP1/P2 P1 M00507A001 Cable (Side A)J1/J2 J1/J2 R20773-G2 CableFigure 5-3: R20602-G2 Standalone Jumper Cable and Wiring Diagram

System Accessories Dummy Load Transmitter R20526Page 64 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryDummy Load Transmitter R20526Dummy Load Transmitter R20526 must be installed on JB of Transmitter PCB.Figure 5-4: Dummy Load Transmitter R20526 To JBCo-Axial Cable Tool Q13628-01The Co-Axial Cable Tool is hex socket tool with a slit down its length. Co-axial cables M00878A001, M00878A002, and Q13578-01 are used for transmission from TRIND overhead antennas and come with hex connectors at either end. The co-axial cable tool allows the installer to tighten cable connections in tight areas of the TRIND card cage and overhead connection box.Note: Co-axial cable Q13578-01 fits in to the slotted side of the co-axial cable tool, allowing the socket to surround the hex head of the cable connector. This allows connections to be made and tightened straight on, rather than from the side. Figure 5-5: Co-axial Cable Tool Q13628-01

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 65Field Strength Sensor Board Q13626-01 System AccessoriesPreliminaryField Strength Sensor Board Q13626-01The TRIND installation manuals and this document detail the installation test for positioning of the field strength sensor board during antenna field tuning.Figure 5-6: Field Strength Sensor Board Q13626-01 Red and black leads The red and black leads of a standard multi-meter, set to DC voltage, are connected to the field strength sensor board leads. As the antennas are tuned by incremental adjustments to the antenna’s variable inductor (similar to a tuning pot), voltage reading increases or decreases. The field strength sensor board allows you to find the voltage peak, which is the tuning target.

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 67Tuning Tool Q13631-01 and Q13631-02 System AccessoriesPreliminaryTuning Tool Q13631-01 and Q13631-02Only the Q13631-01 (part of ASC Tool Kit K94577-01) plastic tuning tool (or similar plastic 0.10-inch hex tool) should be used for tuning overhead antennas. Using a metal screwdriver or Allen wrench has two negative effects. First, proper tuning is impossible as the metal of the tool used changes the properties of the variable inductor used for tuning. Secondly, the ferrite slug used in the variable inductor is extremely brittle and is broken or stripped easily by metal tools, preventing the proper tuning of the antenna. If the antenna is not properly tuned the read range can be significantly reduced.CAUTIONIn conjunction with field strength sensor board Q13626-01, tuning tools Q13631-01 and Q13631-02 are used to make variable inductor adjustments to tune the overhead antennas. The tools are plastic and non-reactive to the variable inductor or board on the overhead antennas, and should only be used to adjust variable inductor.Figure 5-8: Tuning Tool Q13631-01 and Q13631-02 Q13631-01Q13631-02Variable InductorQ13582-02T20579-GXThe Q13631-01 plastic flat blade is used the same as a screwdriver. It’s used with Q13582-02 and fits the slotted head of the variable inductor located on the overhead antenna printed circuit board.The Q13631-02 plastic blade is used the same as an Allen wrench. The wrench is used with T20579-GX and fits the Allen head of the variable inductor located on the overhead antenna printed circuit board (T20579-GX, located in T20632-GX Assemblies).

System Accessories Tuning Tool Q13631-01 and Q13631-02Page 68 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryThis page is intentionally left blank.

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 69Positioning Overhead Antennas Procedures for Factory Installed TRINDPreliminary6 – Procedures for Factory Installed TRINDPositioning Overhead AntennasTRIND overhead antennas are shipped mounted to the unit in the down position. Figure6-1 shows the TRIND antenna hardware and final antenna positioning on the unit.Figure 6-1: TRIND Antenna Hardware Positioning Perform the following procedures to position each overhead antenna:Note: If installing the Mobil Display Cabinet (Blue Hat), leave the antennas in the down position until after the display cabinet is installed. For display cabinet installation instructions, turn to “Dispenser Set-Up” on page 77.Refer to Figure6-1 and perform the following steps to position the overhead antenna into its final position. Perform these steps for each side of the unit.1Loosen the bolts the on each side of the unit that secure the antenna boxes to the antenna brackets using a 3/8-inch nut driver.2Slide the antenna forward and away from the fueling unit in the bracket slots.3Rotate the antenna to the upright position parallel to the ground.Molded TabBolt SlotWiresBolt

Procedures for Factory Installed TRIND Positioning Overhead AntennasPage 70 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013Preliminary4Slide the antenna back towards the unit until the bolts stops in the slots and the molded part of the antenna bracket is secure inside the bracket fork.Note: Prior to tightening the bolts, ensure that the cables coming from the antenna are securely positioned inside the stamped groove part of the bracket and are not trapped under the bracket.5Tighten the bolts that secure the antenna into position using the 3/8-inch nut driver or equivalent.

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 71Addressing Dither Sync Address for LF/UHF Full System Dispenser Set-UpPreliminary7 – Dispenser Set-UpAddressing Dither Sync Address for LF/UHF Full SystemEach dispenser on the G-SITE® system controller must be addressed differently; no two dispensers may have the same address. Addresses are at discretion of the installer.Note: Before installing the card cage inside the dispenser, locate the dip switches on the Data Control Board (DCB) inside the Card Cage Assembly (Figure7-1).Figure 7-1: Data Control Board and Dip Switch Location Switch Numbers = Value1 = Standalone Mode2 = 13 = 24 = 45 = 812345Dip switch downDip switch UpData Control Board (DCB)1From Side A of unit, locate the dip switches on the DCB inside the card cage.2Using switches 2, 3, 4, and 5, address each dispenser so that no two at one site are identical.

Dispenser Set-Up Setting Baud RatePage 72 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminarySetting Baud RateFor major oil company (MOC) TRIND installations, there is no requirement to set or change baud rate.Addressing the Gateway/Enhanced Gateway BoardAddresses for the TRIND device must match the addresses on CRIND® logic board.1Access the unit’s CRIND logic board. Refer to MDE-2562 CRIND Service Manual.2Locate jump jacks on A and B side CRIND logic boards T17764-XX (Figure7-3).3Note position of jump jacks and set jump jacks on Gateway/Enhanced Gateway Board (Figure7-2) to match address on CRIND logic boards (Figure7-3) for both A and B sides.Note: The Gateway Boards are assessable at the upper left hand corner at the front of the card cage.Figure 7-2: Gateway Boards Jump Jack LocationsJump jack locations on Enhanced Gateway Board T20678Jump jack locations on Gateway Board T20128

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 73Addressing the Gateway/Enhanced Gateway Board Dispenser Set-UpPreliminaryFigure 7-3: CRIND T17764-XX Logic BoardU7 Chip orientation notchT17764-XX CRIND logic board (-G3 shown)JP1-16

Dispenser Set-Up Addressing the Gateway/Enhanced Gateway BoardPage 74 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryCRIND Address TableThe following table provides a cross-reference between addresses on CRIND Logic Board T17764 and the Gateway Boards.MOC and Generic CRIND AddressesAddress On CRIND Logic Board T17764-XX JP8 JP7 JP6 JP5 JP4= Address on Gateway Board ‘A’ Side JP6 JP7 JP8 JP9 JP10= Address on Gateway Board ‘B’ Side JP14 JP15 JP16 JP17 JP181IN OUT OUT OUT OUT2OUT IN OUT OUT OUT3IN IN OUT OUT OUT4OUT OUT IN OUT OUT5IN OUT IN OUT OUT6OUT IN IN OUT OUT7IN IN IN OUT OUT8OUT OUT OUT IN OUT9IN OUT OUT IN OUT10 OUT IN OUT IN OUT11 IN IN OUT IN OUT12 OUT OUT IN IN OUT13 IN OUT IN IN OUT14 OUT IN IN IN OUT15 IN IN IN IN OUT16 OUT OUT OUT OUT IN17 IN OUT OUT OUT IN18 OUT IN OUT OUT IN19 IN IN OUT OUT IN20 OUT OUT IN OUT IN21 IN OUT IN OUT IN22 OUT IN IN OUT IN23 IN IN IN OUT IN24 OUT OUT OUT IN IN25 IN OUT OUT IN IN26 OUT IN OUT IN IN27 IN IN OUT IN IN28 OUT OUT IN IN IN29 IN OUT IN IN IN30 OUT IN IN IN IN31 IN IN IN IN IN32 OUT OUT OUT OUT OUT

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 75Preparation for Tuning Antennas Dispenser Set-UpPreliminaryPreparation for Tuning AntennasAntenna tuning requires use of field strength sensor board Q13626-01 supplied with ASC tool kit. See “Field Strength Sensor Board Q13626-01” on page 71.1For units without G-SITE® put unit in ‘standalone’ mode. Refer to “Standalone Jumper Cable R20602-G1 For LF/UHF Full System” on page 67 and “Standalone Jumper Cable R20602-G2 For Enhanced Gateway” on page 69. 2Restore power to unit(s).3After restoring power to the unit, verify that the unit is in “standalone” mode by observing that the LEDs on the light board are flashing.Tuning AntennasThe following sections provide instructions on tuning the Single-Loop and Mobil antennas.Tuning Single-Loop AntennasPerform the following steps in to tune a Single-Loop Antenna.1Locate the access port for the tuning pot in the over-head antenna connection box on Side 1. Note: Use tuning tool Q13631-XX from the ASC TRIND tool kit to make pot adjustments. Refer to MDE-3640 ASC TRIND Tool Kit for instructions. Hex end of tuning tool matches hex shape of tuning pot.2Lay field strength sensor on the antenna as shown on Figure7-4. Exact location is not critical.Figure 7-4: Field Strength Senor Positioning Tuning Pot Access Port Location In Overhead Antenna Connection BoxField Strength SensorUnderside of Antenna View

Dispenser Set-Up Tuning AntennasPage 76 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013Preliminary3On the card cage, move the three position “tune” toggle switch (Figure7-5) from center position to “A”.Figure 7-5: Tune Toggle Switch LocationsBAABTune Toggle Switch Location4Connect the leads to field strength sensor. Position the multi-meter selector switch to DC voltage.5By fine adjustments to tuning pot, set to highest DC voltage reading.6Voltage will peak at a point, and then decrease with turns in either direction. Set at peak.7Repeat Steps 1 through 5 for position “B” and then return tune toggle switch to center position.

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 77Tuning Antennas Dispenser Set-UpPreliminaryMobil AntennasPerform the following steps to tune a Mobil Antenna.1Locate variable inductor on printed circuit board in the over-head antenna connection box. The variable inductor, similar to a tuning pot, has a slot for the tuning tool. See “T20231 Mobil Overhead Antenna Assembly” on page 32.2The variable inductor on the side A over head antenna connection box should be turned out 5 to 6 turns as a starting point. Note: Use tuning tool Q13631-01 from the ASC TRIND tool kit to make adjustments.Figure 7-6: Variable Inductor LocationVariable inductor location in overhead antenna connection boxVariable inductor Use tuning tool to adjustJ13Lay field strength sensor flat at a position (Figure7-7) on the “A” side plastic antenna housing, to the right of connection box.Figure 7-7: Field Strength Sensor Location on Side A Position field strength sensorQ13626-01Note: For consistent readings always place sensor board in the same spot during testing.

Dispenser Set-Up Tuning AntennasPage 78 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013Preliminary4On card cage, move the three position “tune” toggle switch from the center position to “A”.Figure 7-8: Tune Toggle Switch Location ‘Tune’ toggle switch location5Connect the leads on the multi-meter to field strength sensor. Set the meter to the DC voltage range.6By fine adjustments to variable inductor, set to the highest DC voltage reading.Note: Voltage will peak at a point between 12VDC and 20VDC, and then decrease with turns in either direction. Set at peak.7Repeat Steps 1 through 6 for ‘B’ side.8 When finished, return the tune toggle switch to the center position.

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 79Status Indicators Testing and TroubleshootingPreliminary8 – Testing and TroubleshootingThe following sections provide testing and troubleshooting information for the TRIND system. The status indicator section describes the characteristics of key TRIND indicators when the TRIND system is operating properly. The troubleshooting flow chart section provides a graphical guide to assist in troubleshooting the TRIND system.Note: The majority of failures that occur are attributed to insufficient initial setup detail. Proper Gateway Board addressing and accurate cable connections are crucial to the effective operation of the TRIND system.Status IndicatorsThe following sections describe the display characteristics of key indicators when the TRIND system is functioning properly.T20128 Gateway BoardStatus indicators for Gateway Board T20128 are depicted on Figure8-1. Figure 8-1: Gateway Board T20128 CR9 CR8CR6CR5CR4CR10T20128 Gateway Board CR7

Testing and Troubleshooting Status IndicatorsPage 80 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryThe T20128 Gateway Board will have the following indicator characteristics when operating properly:• +5VDC LED on solid (CR8)• Blinking CPU LED (CR6). A dimly lit LED can also indicate proper operation because the blink rate has become so fast that the LED appears dimmer than the +5VDC LED (CR8)• Rapidly Blinking CRIND A&B LEDs. Side A is CR4 (TX), CR5 (RX), Side B is CR9 (TX). These LEDs indicate good communication with the CRIND. They mimic the LEDs on the T17764 series of CRIND boards. The Encore 500 Series CRIND node has two TRIND LEDs, D12 and D13, present on board beneath the TRIND connector.T20678 Enhanced Gateway BoardStatus indicators for Enhanced Gateway Board T20678 are depicted on Figure8-2.Figure 8-2: Enhanced Gateway Board T20678 CR9CR8CR6CR5CR4CR10T20678 Enhanced Gateway BoardCR7

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 81Status Indicators Testing and TroubleshootingPreliminaryEnhanced Gateway Board T20678 will have the following indicator characteristics when operating properly:• +5VDC LED on solid (CR8)• Blinking CPU LED (CR6). A dimly lit LED can also indicate proper operation because the blink rate has become so fast that the LED appears dimmer than the +5VDC LED (CR8)• Rapidly Blinking CRIND A&B LEDs. Side A is CR4 (TX), CR5 (RX), Side B is CR9 (TX). These LEDs indicate good communication with the CRIND. They mimic the LEDs on the T17764 series of CRIND boards. The Encore 500 Series CRIND node has two TRIND LEDs, D12 and D13, present on board beneath the TRIND connector.Q13563 Data Control BoardStatus indicators for Data Control Board Q13563-01 is shown on Figure8-3, the status indicator s for Data Control Board Q13563-04 are depicted on Figure8-4.Figure 8-3: Data Control Board Q13563-01 Heart Beat (CPU)RS-485 (TX)Read Ant 1Read Ant 3Bezel I/O ErrorRS-485 (RX)12 VDCVcc (+5VDC)J8 Bezel BJ7 Bezel A

Testing and Troubleshooting Status IndicatorsPage 82 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryFigure 8-4: Data Control Board Q13563-04 Heart Beat (CPU)RS-485 (TX)Read Ant 1 (Overhead)Read Ant 3 (Overhead)Bezel I/O ErrorRS-485 (RX)+12VDCVcc (+5VDCJ8 Bezel BJ7 Bezel AThe Q13563 Data Control Board will have the following indicator characteristics when operating properly:• VCC and +12VDC LEDs on solid (D14 & D13, respectively)• Heartbeat LED (CPU) blinking (D9)• RS-485 LED's strobbing rapidly (D2 &D3) Note: One may watch the communications begin between the Gateway board and the DCB with these LEDs. The first several sequences are the waking up of the DCB and then commands sent down. This LED activity looks spurious. After a few rounds of that behavior, the RS-485 LEDs will begin firing at a regular pace, indicating that a link has been established. The RS-485 LEDs fire at a regular pace only when the Gateway board is looking for tags. When the CRIND doesn’t want the Gateway to look for tags (or has never initiated communication with the Gateway), the RS-485 LEDs fire once every 10 seconds after any initial wakeup.• When a car tag has been presented, the READ ANT 1 (D8) or READ ANT 3 (D7) LED will light, depending upon the side. •If the Bezel I/O error LED (D6) is on, then one of the Light/MicroReader boards is not connected or has lost communication

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 83Status Indicators Testing and TroubleshootingPreliminaryT20601/M01560 Light/Micro Reader BoardsThe T20601/M01560 Light/Micro Reader Boards (Figure8-5) will exhibit the following characteristic when operating properly:Note: The M01560 is a subassembly of M01218 Light and Inductor PCB Assembly•SYNC LED blinking (CR1)• OKT LED on solid (CR2) until a tag is presented, then it will flicker while a key tag is in the field• STAT LED (CR3) blinking in unison with the SYNC LED• If these LEDs are solid, then the TRIND has not been told to look for tags, and consequently will never light the LEDs on the Light/MicroReader board. Figure 8-5: RFID Light/Micro Reader Boards SYNC OKT STATM01560 RFID Light/Micro Reader BoardSYNC OKT STATT20601 RFID Light/Micro Reader Board

Testing and Troubleshooting Isolating TRIND from CRINDPage 84 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryIsolating TRIND from CRINDTo isolate the TRIND system from CRIND, do the following:1Shut off all power to unit.2Disconnect either A or B side R20519-G3 cable from either J8 (B side) or J7 (A side) on the DCB in the TRIND card cage, and insert the standalone jumper in-line (between J8 and P8 or between J7 and P7). For jumper details refer to “Standalone Jumper Cable R20602-G1 For LF/UHF Full System” on page 67.Note: If Standalone Jumper Cable R20602-G1 or 9 volt alkaline battery is not available, unit can be put in standalone mode by installing jump jack on JP3 on Light/Microreader Board (see “Light/Microreader PCB T20446-G1, T20601-GX, M01580A001, and M01580A002” on page 50). Perform for Side A only for the T20606-G3 Card Cage.3Remove J4 from Data Control Board.4Restore power to unit, and test TRIND operation (see “Dummy Load Transmitter R20526” on page 70). If TRIND functions properly the problem is with CRIND or CRIND related equipment. Refer to MDE-2562 CRIND Service Manual.Tag TestingPerform the following procedures to begin TRIND tag testing. To test the full controller drive capability do not place TRIND in the standalone mode. Allow the dispenser network to detect the other subsystems (pump, CRIND, TRIND, etc.). The standalone procedure will verify that TRIND hardware is good (or not). The standalone procedure isolates TRIND from CRIND.Car Mounted Test Tags1Place the unit into the standalone mode. Refer to “Standalone Jumper Cable R20602-G1 For LF/UHF Full System” on page 67 for the appropriate standalone cable connection.2From “A” side of the unit, hold the car mount test tag (Q13630-01 from the ASC TRIND tool kit) in front of unit at a distance of approximately 6 feet from the face of unit. Observe that the door or faceplate TRIND indicator will light.3Repeat Steps 1 and 2 for the “B” side.

MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013 Page 85Tag Testing Testing and TroubleshootingPreliminaryHand Held Test TagsPerform the following steps to test the Hand Held tag.1Place the unit into the standalone mode. Refer to “Standalone Jumper Cable R20602-G2 For Enhanced Gateway” on page 69 for the appropriate standalone cable connection.2From Side 1 of the unit, point the hand held test tag (Q13630-02 from the ACS TRIND tool kit) at the TRIND target graphic (Figure8-6). The TRIND indicator will light when the tag is approximately 3 inches or less away for the target graphic. Repeat for side 2.Note: If the indicator fails to light, check whether the light on the other side is on; if so, it indicates a crossing of side 1 and 2 cables. Check the connections.Figure 8-6: TRIND Hand Held Test Tag PositioningTarget GraphicPOINT MUST BE WITHIN 3 TO 6 INCHES OF TARGET IMPORTANT!3Repeat Steps 1 and 2 for Side 2.

$Testing and Troubleshooting Tag TestingPage 86 MDE-3664B TRIND Start-Up, Service, and Parts Manual . March 2013PreliminaryAlternative Testing Using LaptopPerform the following steps to implement TRIND testing using the Laptop Tool.1Connect laptop to RS232 port on DCB.Note: The directory paths shown in steps 2 through 4, are representative of a directory structure that may be found on a laptop personal computer. Some directory paths may differ depending upon the computers software setup and hardware configuration.2Go to: “C:\windows program (hyperterminal)\Accessories\Terminal\Settings\Communications”3Set for:• 9600 baud•8 bit• No parity• Comm 14Then go to:• Help screen\Antenna scanNext, at “Antenna scan”, select 1, 2, 3 and 4Note: This will test both antennas5From Side A of unit position the hand held test tag (Q13630-02 from the ACS TRIND tool kit) in front of the TRIND target graphic. Observe that the door or faceplate TRIND indicator lights.6From Side A of unit hold the car mount test tag (Q13630-01 from the ASC TRIND tool kit) in front of unit, at a distance of approximately 6 feet from overhead antenna. Observe that the door or faceplate TRIND indicator lights.7Repeat Steps 5 and 6 for Side B.$

Gilbarco LFADV RFID Module User Manual 13 0074 Exhibit Cover

Gilbarco Inc. RFID Module 13 0074 Exhibit Cover

Manual

Navigation menu

Namespaces

Views

Navigation