Gibson Innovations SHB4305 In-ear Bluetooth Headphones User Manual

Gibson Innovations Limited In-ear Bluetooth Headphones Users Manual

Users Manual

SHB4305BASS+User manualRegister your product and get support atwww.philips.com/support
1ENContentsContents1 Important safety instructions 2Hearing Safety 2General information 22 Your Bluetooth in-ear headphones 3What's in the box 3Other devices 3Overview of your Bluetooth in-ear headphones 33 Get started 5Charge your headphones 5Pair the headphones with your mobile phone 54 Use your headphones 6Connect the headphones to a Bluetooth device 6Manage your calls and music 6How to wear 7Choose your best t for big, bold bass 75 Technical data 86 Notice 9Declaration of conformity 9Disposal of your old product and battery 9Compliance with EMF 9Trademarks 107 Frequently asked questions 11
2EN1 Important safety instructionsHearing Safety Danger •To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is.Be sure to observe the following guidelines when using your headset.• Listen at reasonable volumes for reasonable periods of time.• Be careful not to adjust the volume continuously upwards as your hearing adapts.• Do not turn up the volume so high that you can’t hear what’s around you.• You should use caution or temporarily discontinue use in potentially hazardous situations.• Excessive sound pressure from earphones and headphones can cause hearing loss.• Using headphones with both ears covered while driving is not recommended and may be illegal in some areas while driving.• For your safety, avoid distractions from music or phone calls while in trac or other potentially dangerous environments.General informationTo avoid damage or malfunction:Caution •Do not expose headphones to excessive heat. •Do not drop your headphones. •Headphones shall not be exposed to dripping or splashing. •Do not allow your headphones to be submerged in water. •Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives. •If cleaning is required use a soft cloth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product. •The integrated battery shall not be exposed to excessive heat such as sunshine, re or the like. •Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.About operating and storage temperatures and humidity• Operate or store in a place where temperature is between -15ºC (5ºF) and 55ºC (131ºF) (up to 90% relative humidity.• Battery life may be shorter in high or low temperature conditions.
3EN2 Your Bluetooth in-ear headphonesCongratulations on your purchase, and welcome to Philips! To fully benet from the support that Philips oers, register your product at www.philips.com/welcome.With this Philips wireless in-ear headphones, you can:• enjoy convenient wireless handsfree calls;• enjoy and control wireless music;• switch between calls and music.What's in the box Philips Bluetooth in-ear headphones SHB4305 Replaceable ear tips USB charging cable (for charging only) Quick start guideOther devicesA mobile phone or device (e.g. notebook, PDA, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible to the headphones (see ‘Technical data’ on page 8).Overview of your Bluetooth in-ear headphones R35124
4ENa Multi-function buttonb Microphone (back side)c Volume/Track control buttond LED indicatore Micro USB charging slot
5EN3 Get startedCharge your headphonesWarning •Only charged with certied USB adapter DC 5V/0.5A.Note •Before you use your headphones for the rst time, charge the battery for 3 hours for optimum battery capacity and lifetime. •Use only the original USB charging cable to avoid any damage. •Finish your call before charging the headphones, as connecting the headphones for charging will power the headphones o.Connect the supplied USB charging cable to: • the micro USB charging slot on the headphones and; • the charger/USB port of a computer. » LED turns white during charging and turns o when the headphones is fully charged.Tip •Normally, a full charge takes 2 hours.Pair the headphones with your mobile phoneBefore you use the headphones with your mobile phone for the rst time, pair it with a mobile phone. A successful pairing establishes a unique encrypted link between the headphones and mobile phone. The headphones store the last 8 devices in the memory. If you try to pair more than 8 devices, the earliest paired device is replaced by the new one. 1 Make sure that the headphones are fully charged and turned o.2 Press and hold the multi-function button for 6 seconds until the blue and white LED ashes alternately. » The headphones remain in pairing mode for 5 minutes.3 Make sure that the mobile phone is turned on and its Bluetooth feature is activated.4 Pair the headphones with the mobile phone. For detailed information, refer to the user manual of your mobile phone.The following example shows you how to pair the headphones with your mobile phone.1 Activate the Bluetooth feature of your mobile phone, select BASS+ In-Ear.2 Enter the headset password "0000" (4 zeros) if prompted. For those mobile phones featuring Bluetooth 3.0 or higher, no need to enter a password.BASS+ In-EarSHB4405
6EN4 Use your headphonesConnect the headphones to a Bluetooth device1 Turn on your mobile phone/Bluetooth device. 2 Press and hold the multi-function button for 2 seconds to turn the headphones on. » The blue LED ashes. » The headphones are reconnected to the last connected mobile phone/Bluetooth device automatically. If the last one is not available, the headphones try to reconnect to the second last connected device.Tip •If you turn on the mobile phone/Bluetooth device or activate the Bluetooth feature after turning on the headphones, you have to reconnect the headphones and mobile phone/Bluetooth device manually.Note •If the headphones fail to connect to any Bluetooth device within range in 5 minutes, it will switch o automatically to save the battery life.Manage your calls and musicOn/o Task Button OperationTurn the headphones on.Multi-function buttonPress and hold for 2 seconds. » The blue LED ashes.Turn the headphones o.Multi-function buttonPress and hold for 6 seconds. » The white LED is on and fades out. Music control Task Button OperationPlay or pause music.Multi-function buttonPress once.Adjust volume.+/-Press once.Skip forward. +Press and hold for 2 seconds.Skip backward.-Press and hold for 2 seconds.
7ENCall controlTask Button OperationPick up/hang up a call.Multi-function buttonPress once. » 1 beep.Switch caller during a call.Multi-function buttonPress twice.Other headphones indicator status Headphones statusIndicatorThe headphones are connected to a Bluetooth device, while the headphones in standby mode or while you are listening to music.The blue LED ashes for every 8 seconds.The headphones are ready for pairing.The LED ashes blue and white alternately.The headphones are on but not connected to a Bluetooth device.The blue LED ashes quickly.If no connection can be made, the headphones will turn itself o within 5 minutes.Low battery level. The white LED ashes 2 times for every 150 seconds until it is out of power.Battery is fully charged.The white LED is o.How to wear1 23 4Choose your best t for big, bold bass L M S
8EN5 Technical data• Music time: 6 hours• Talk time: 5.5 hours• Standby time: 110 hours• Normal time for a full charge: 2 hours• Rechargeable lithium polymer battery (110 mAh)• Bluetooth 4.1, Bluetooth mono support (Headset Prole - HSP, Hands-Free Prole - HFP), Bluetooth stereo supported (Advanced Audio Distribution Prole - A2DP; Audio Video Remote Control Prole - AVRCP)• Frequency range: 2.402-2.480GHz• Transmitter power: <20dBm• Operating range: Up to 10 meters (33 feet)• Digital echo & noise reduction • Auto power oNote •Specications are subject to change without notice.
9EN6 NoticeDeclaration of conformityHereby, Gibson Innovations declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can nd the Declaration of Conformity on www.p4c.philips.com.Disposal of your old product and battery Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. This symbol on a product means that the product is covered by European Directive 2012/19/EU. This symbol means that the product contains a built-in rechargeable battery covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. We strongly advise you to take your product to an ocial collection point or a Philips service centre to have a professional remove the rechargeable battery. Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health.Remove the integrated batteryNote •Make sure the headphones are disconnected from the USB charging cable before removing the battery.If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing the headphones. Compliance with EMFThis product complies with all applicable standards and regulations regarding exposure to electromagnetic elds.Environmental informationAll unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three
10 ENmaterials: cardboard (box), polystyrene foam (buer) and polyethylene (bags, protective foam sheet.)Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.TrademarksBluetoothThe Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Gibson Innovations Limited is under license. Other trademarks and trade names are those of their respective owners.
7 Frequently asked questionsMy Bluetooth headphones do not switch on.The battery level is low. Charge the headphones. I cannot pair my Bluetooth headphones with a mobile phone.The Bluetooth is disabled. Enable the Bluetooth feature on your mobile phone and turn on the mobile phone before you turn on the headphones. Pairing does not work.Make sure the headphones are in pairing mode.• Follow the steps described in this user manual (see ‘Pair the headphones with your mobile phone’ on page 5). • Make sure that the LED light ashes blue and white alternately before you release the multi-function button. Do not stop holding the button if you see the blue LED only. The mobile phone cannot nd the headphones. •The headphones may be connected to a previously paired device. Turn o the connected device or move it out of range. •Pairing may have been reset or the headphones have been previously paired with another device. Pair the headphones with the mobile phone again as described in the user manual. My Bluetooth headphones are connected to a Bluetooth stereo enabled mobile phone, but music only plays on the mobile phone speaker.Refer to the user manual of your mobile phone. Select to listen to music through the headphones. The audio quality is poor and crackling noise can be heard.The Bluetooth device is out of range. Reduce the distance between your headphones and Bluetooth device, or remove obstacles between them. The audio quality is poor when streaming from the mobile phone is very slow, or audio streaming does not work at all.Make sure your mobile phone not only supports (mono) HSP/HFP but also supports A2DP (see ‘Technical data’ on page 8). I hear but cannot control music on my Bluetooth device (e.g. play/pause/skip forward/backward).Make sure the Bluetooth audio source supports AVRCP (see ‘Technical data’ on page 8).
12How do I get the best bass performance from my earphones? For optimum bass performance, a good seal is required between the earphones and your ear canals. Human ears are all unique – size and shape varies from person to person, which is why the earphones come with three pairs of dierently designed ear tips. Try each of them when playing music, and choose the pair that oers the best comfort and bass performance. You should notice that the correctly tting ear tips also block out more of the background noise. For further support, visit www.philips.com/support.
2017 © Gibson Innovations Limited. All rights reserved.This product has been manufactured by, and is sold under the responsibility of Gibson Innovations Ltd., and Gibson Innovations Ltd. is the warrantor in relation to this product. Philips and the Philips’ Shield Emblem are registeredtrademarks of Koninklijke Philips N.V.UM_SHB4305_00_EN_V1.0WK1723
正面 反面尺寸为：89*141.5mm

Navigation menu